Search Results

Search found 3296 results on 132 pages for 'executable compression'.

Page 92/132 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

• Windows 7 - "A disk read error occured. Press Ctrl + Alt + Del to restart"

  - by Senthil

  Problem: When I switch on my PC, after BIOS POST, a cursor is blinking for about 5 seconds and then I am getting this error message: A disk read error occurred. Press Ctrl + Alt + Del to restart. I am able to go into BIOS. But Windows loader doesn't even start. This message is shown after my motherboard logo comes and goes. Symptoms: I DID notice my system freezing for minutes at a time for past two days. Also, in the past two days, it stopped half way through the Window booting process. I had to do hard reset couple of times to get it working. But since today morning, I only get this error message. Configuration: Operating System: Windows 7 Ultimate 32-bit only. Hard disk: 1 Physical Disk - 80GB SATA Partitions: Two (2) - C: and D: File System: NTFS No drive encryption or compression is turned on. After I searched on the net, I have found people mentioning these possible causes: Hard Disk is physically failing Corrupt MBR Bad Sector I am planning to buy a new hard disk, install Windows on it and continue. But I need data from the old hard disk. The data I want is in D: drive, outside any Windows user folder, is not encrypted or compressed or protected in anyway. I think if someone/something can get the disk working again and knows NTFS, the data can be hopefully read. What steps should I follow to recover files from the defective disk? Update: I bought a new disk, installed windows on it and added the defective one as a slave. Then I was able to read the data from the defective hard disk. Though chkdsk found lots of errors, the files I wanted were not affected and I got them back :) I am not using that hard disk anymore though it seems to be working at the moment.

  Read the article

• adding an existing implementation file to an xcode project won't work

  - by karsten

  As I write most of my code using MacVIM, I need to add the new files to the XCode project in order to compile them into the executable. Today however I encoutered an implementation file (.m) wich XCode won't allow to be added. It appears light gray the appropriate finder window as if it were already included in the project, but when I try to build, I get a linker error, stating that the symbol defined this implementation file could not be found. The corresponding header file could be added without problems. Any idea what could have caused this problem? Btw. I deleted a former version of the same file from the "Classes" tree before, as well as many others wich were successfully re-added. Thanks in advance.

  Read the article

• Code Access Security - Basics and Example

  - by jobless-spt

  I was going through this link to understand CodeAccessSecurity: http://www.codeproject.com/KB/security/UB_CAS_NET.aspx It's a great article but it left me with following questions: If you can demand and get whatever permissions you want, then any executable can get Full_Trust on machine. If permissions are already there, then why do we need to demand those? Code is executing on Server, so the permissions are on server not on client machine? Article takes an example of removing write permissions from an assembly to show security exception. Though in real world, System.IO assembly (or related classes) will take care of these permissions. So is there a real scenario where we will need CAS?

  Read the article

• Dual Monitor support rdp 7 to win 7 on esxi

  - by rphilli5

  I am trying to RDP from a Windows 7 Professional dual monitor physical machine to a Windows 7 Professional VM hosted on esxi 4.0. I can get the spanning option to work to both monitors, but I have tried 3 different methods of connecting but have not been able to use true multiple monitors. At different times, I tried checking the "use all monitors" option, command line mstsc /multimon and added the line use multimon:i:1 to the .rdp file. None of these worked. Any ideas? The physical machine can connect to other Windows 7 physical machines with true multi monitor access. I also have the same issue when going from a 32bit RC1 machine to a Windows 7 Professional x64, but not when going in the reverse direction. Here's the .rdp: screen mode id:i:2 use multimon:i:1 desktopwidth:i:1440 desktopheight:i:900 session bpp:i:16 winposstr:s:0,1,341,118,1139,568 compression:i:1 keyboardhook:i:2 audiocapturemode:i:0 videoplaybackmode:i:1 connection type:i:1 displayconnectionbar:i:1 disable wallpaper:i:1 allow font smoothing:i:0 allow desktop composition:i:0 disable full window drag:i:1 disable menu anims:i:1 disable themes:i:1 disable cursor setting:i:0 bitmapcachepersistenable:i:1 full address:s:192.168.1.5 audiomode:i:0 redirectprinters:i:1 redirectcomports:i:0 redirectsmartcards:i:1 redirectclipboard:i:1 redirectposdevices:i:0 redirectdirectx:i:1 autoreconnection enabled:i:1 authentication level:i:2 prompt for credentials:i:0 negotiate security layer:i:1 remoteapplicationmode:i:0 alternate shell:s: shell working directory:s: gatewayhostname:s: gatewayusagemethod:i:4 gatewaycredentialssource:i:4 gatewayprofileusagemethod:i:0 promptcredentialonce:i:1 use redirection server name:i:0 drivestoredirect:s:

  Read the article

• Why is uploading to S3 so slow?

  - by Tom Marthenal

  I am using s3cmd to upload to S3: # s3cmd put 1gb.bin s3://my-bucket/1gb.bin 1gb.bin -> s3://my-bucket/1gb.bin [1 of 1] 366706688 of 1073741824 34% in 371s 963.22 kB/s I am uploading from Linode, which has an outgoing bandwidth cap of 50 Mb/s according to support (roughly 6 MB/s). Why am I getting such slow upload speeds to S3, and how can I improve them? Update: Uploading the same file via SCP to an m1.medium EC2 instance (SCP from my Linode to the instance's EBS drive) gives about 44 Mb/s according to iftop (any compression done by the cipher is not a factor). Traceroute: Here's a traceroute to the server it's uploading to (according to tcpdump). # traceroute s3-1-w.amazonaws.com. traceroute to s3-1-w.amazonaws.com. (72.21.194.32), 30 hops max, 60 byte packets 1 207.99.1.13 (207.99.1.13) 0.635 ms 0.743 ms 0.723 ms 2 207.99.53.41 (207.99.53.41) 0.683 ms 0.865 ms 0.915 ms 3 vlan801.tbr1.mmu.nac.net (209.123.10.9) 0.397 ms 0.541 ms 0.527 ms 4 0.e1-1.tbr1.tl9.nac.net (209.123.10.102) 1.400 ms 1.481 ms 1.508 ms 5 0.gi-0-0-0.pr1.tl9.nac.net (209.123.11.62) 1.602 ms 1.677 ms 1.699 ms 6 equinix02-iad2.amazon.com (206.223.115.35) 9.393 ms 8.925 ms 8.900 ms 7 72.21.220.41 (72.21.220.41) 32.610 ms 9.812 ms 9.789 ms 8 72.21.222.141 (72.21.222.141) 9.519 ms 9.439 ms 9.443 ms 9 72.21.218.3 (72.21.218.3) 10.245 ms 10.202 ms 10.154 ms 10 * * * 11 * * * 12 * * * 13 * * * 14 * * * 15 * * * 16 * * * 17 * * * 18 * * * 19 * * * 20 * * * 21 * * * 22 * * * 23 * * * 24 * * * 25 * * * 26 * * * 27 * * * 28 * * * 29 * * * 30 * * * The latency looks reasonable, at least until the server stopped responding to ping requests.

  Read the article

• getting "implicit declaration of function 'fcloseall' is invalid in C99" when compiling to gnu99

  - by Emanuel Ey

  Consider the following C code: #include <stdio.h> #include <stdlib.h> void fatal(const char* message){ /* Prints a message and terminates the program. Closes all open i/o streams before exiting. */ printf("%s\n", message); fcloseall(); exit(EXIT_FAILURE); } I'm using clang 2.8 to compile: clang -Wall -std=gnu99 -o <executable> <source.c> And get: implicit declaration of function 'fcloseall' is invalid in C99 Which is true, but i'm explicitly compiling to gnu99 [which should support fcloseall()], and not to c99. Although the code runs, I don like the have unresolved warnings when compiling. How can i solve this?

  Read the article

• What are the Build Settings for a Universal iPhone and iPad Application

  - by McPragma

  What would be the settings to build and have accepted an universal app for both the iPad and iPhone? That is, what would be the settings in Project X Info Build for Architectures [ARCHS] ("Standard(armv6)" or "Optimized(armv6 armv7)" or other) Valid Architectures [VALID_ARCHS] ("armv6 armv7" or other) Build Active Architecture Only (checked or unchecked) and what would we select in the dropdown (Device - 3.2|Distribution|armv?) ? We're either getting warnings at build time that we haven't built for armv7, or the app upload is rejected on account of "The binary you uploaded was invalid. When supporting iPhone, the executable must include support for the armv6 architecture". Thank you for your help.

  Read the article

• Java "constant string too long" compile error. Only happens using Ant, not when using Eclipse

  - by Allan

  I have a few really long strings in one class for initializing user information. When I compile in Eclipse, I don't get any errors or warnings, and the resulting .jar runs fine. Recently, I decided to create an ant build file to use. Whenever I compile the same class with ant, I get the "constant string too long" compile error. I've tried a number of ways to set the java compiler executable in ant to make sure that I'm using the exact same version as in Eclipse. I'd rather figure out how to get the same successful compile I get in Eclipse in Ant than try to rework the code to dynamically concatenate the strings.

  Read the article

• Real-time local backup with versioning on Windows 7/8

  - by Borda

  I'm looking for a reliable backup solution on Windows, something with a feature set similar to Yadis. I've been using CrashPlan for 2 months, but their software lost more than 1TB of my data, that's why I'm looking for alternatives. Requirements: Real-time folder-to-folder backup: I don't need online features, I want to use this to duplicate my files between my local disks. Versioning support: Should be able to choose how many versions to keep of the files. Plain backup: I'd like to be able to open the backup without special software. No proprietary file format. External disk support: Shouldn't have any problem using external disks, at least on the source side. Backup every file, even locked/system files. (Yadis fails this one) Should start automatically, and have a comfortable GUI. Should use actively maintained and/or popular software. I don't want to use discontinued products. Optional requirements: Low RAM usage I'm not really comfortable with something that eats 1GB of my RAM. Compression support Preferably ZIP, but I'm not picky about this. Any ordinary everyday format is acceptable. Freeware or Open Source Preferred, but not necessary. I can do a one-time payment within reasonable bounds. (preferably under $100) I only need Windows support, but if it works on Linux, that's a plus. I've already searched and tried lots of software, most of them failed at the plain backup, the versioning or the locked file backup requirements.

  Read the article

• Forward all traffic through an ssh tunnel

  - by Eamorr

  I hope someone can follow this and I'll explain as best I can. I'm trying to forward all traffic from port 6999 on x.x.x.224, through an ssh tunnel, and onto port 7000 on x.x.x.218. Here is some ASCII art: |browser|-----|Squid on x.x.x.224|------|ssh tunnel|------<satellite link>-----|Squid on x.x.x.218|-----|www| 3128 6999 7000 80 When I remove the ssh tunnel, everything works fine. The idea is to turn off encryption on the ssh tunnel (to save bandwidth) and turn on maximum compression (to save more bandwidth). This is because it's a satellite link. Here's the ssh tunnel I've been using: ssh -C -f -C -o CompressionLevel=9 -o Cipher=none [email protected] -L 7000:172.16.1.224:6999 -N The trouble is, I don't know how to get data from Squid on x.x.x.224 into the ssh tunnel? Am I going about this the wrong way? Should I create an ssh tunnel on x.x.x.218? I use iptables to stop squid on x.x.x.224 from reading port 80, but to feed from port 6999 instead (i.e. via the ssh tunnel). Do I need another iptables rule? Any comments greatly appreciated. Many thanks in advance,

  Read the article

• Where is a good place for a code review?

  - by Carlos Nunez

  Hi, all! A few colleagues and I created a simple packet capturing application based on libpcap, GTK+ and sqlite as a project for a Networks Engineering course at our university. While it (mostly) works, I am trying to improve my programming skills and would appreciate it if members of the community could look at what we've put together. Is this a good place to ask for such a review? If not, what are good sites I can throw this question up on? The source code is hosted by Google Code (http://code.google.com/p/nbfm-sniffer) and an executable is available for download (Windows only, though it does compile on Linux and should compile on OS X Leopard as well provided one has gtk+ SDK installed). Thanks, everyone! -Carlos Nunez

  Read the article

• Setting Xcode's target to iPhone NOT iPad

  - by Garry

  I just upgraded to iPhone SDK 3.2 Beta 4. Since doing so, I have not been able to get the app to launch in the iPhone simulator - it keeps launching in the iPad simulator. I have tried option-clicking the drop-down menu in the top left-corner of Xcode and setting 'Active Executable' to iPhone simulator 3.1.3 but it keeps going back to iPad simulator instead. What gives? I have no interest in my app running on the iPad and I don't want to test it in the 2X mode in the simulator. Thanks,

  Read the article

• Batch File input validation - Make sure user entered an integer

  - by B2Ben

  I'm experimenting with a DOS batch file to perform a simple operation which requires the user to enter a non-negative integer. I'm using simple batch-file techniques to get user input: @ECHO OFF SET /P UserInput=Please Enter a Number: The user can enter any text they want here, so I would like to add some routine to make sure what the user entered was a valid number. That is... they entered at least one character, and every character is a number from 0 to 9. I'd like something I can feed the UserInput into. At the end of the routine would be like an if/then that would run different statements based on whether or not it was actually a valid number. I've experimented with loops and substrings and such, but my knowledge and understanding is still slim... so any help would be appreciated. I could build an executable, and I know there are nicer ways to do things than batch files, but at least for this task I'm trying to keep it simple by using a batch file.

  Read the article

• problem in decoupling urls.py , while following a tutorial of django

  - by Nitin Garg

  http://docs.djangoproject.com/en/dev/intro/tutorial03/ I was at the step Decoupling the URLconfs where the tutorial illustrates how to decouple urls.py. On doing exactly what it says, i get the following error- error at /polls/1/ nothing to repeat Request Method: GET Request URL: http://localhost:8000/polls/1/ Exception Type: error Exception Value: nothing to repeat Exception Location: C:\jython2.5.1\Lib\re.py in _compile, line 241 Python Executable: C:\jython2.5.1\jython.bat Python Version: 2.5.1 Python Path: ['E:\\Programming\\Project\\django_app\\mysite', 'C:\\jython2.5.1\\Lib\\site-packages\\setuptools-0.6c11-py2.5.egg', 'C:\\jython2.5.1\\Lib', '__classpath__', '__pyclasspath__/', 'C:\\jython2.5.1\\Lib\\site-packages'] Server time: Mon, 12 Apr 2010 12:02:56 +0530

  Read the article

• gcc linking shared libraries with dependent libraries

  - by Geng

  I have a complicated project with multiple executable targets and multiple shared libraries. The shared libraries currently don't have their dependent shared libraries linked in, and the result is that linker arguments to build the executables are hideously long and hard to maintain. I'd like to add in the dependencies so the Makefiles become much cleaner. I want to add the following (example): gcc -shared -o libshared.so -lshared_dependent1 -lshared_dependent2 objfile1.o objfile2.o Is there a way to test if all the symbols in libshared.so will resolve based on that line? Is there a way to print out if any of the shared_dependent libraries specified were unnecessary? Thanks in advance.

  Read the article

• What's the best way to resolve a filepath?

  - by BillyONeal

  Hello everyone :) I've got a series of filepaths that look something like this: C:\Windows\System32\svchost.exe -k LocalSystemNetworkRestricted C:\Windows\System32\svchost C:\Program Files (x86)\Common Files\Steam\SteamService.exe /RunAsService "C:\Program Files (x86)\Common Files\Steam\SteamService.exe" /RunAsService and I need to find these paths' actual locations. So, respectively, the above would be: C:\Windows\System32\svchost.exe C:\Windows\System32\svchost.exe C:\Program Files (x86)\Common Files\Steam\SteamService.exe C:\Program Files (x86)\Common Files\Steam\SteamService.exe What's the best way to go about doing this? Does windows have an API function to accomplish it? I essentially am trying to figure out what executable CreateProcess will call if I pass it that path. Thanks! Billy3

  Read the article

• Is Private Bytes >> Working Set normal?

  - by Jacob

  OK, this may sound weird, but here goes. There are 2 computers, A (Pentium D) and B (Quad Core) with almost the same amount of RAM running Windows XP. If I run the same code on both computers, the allocated private bytes in A never goes down resulting in a crash later on. In B it looks like the private bytes is constantly deallocated and everything looks fine. In both computers, the working set is deallocated and allocated similarly. Could this be an issue with manifests or DLLs (system)? I'm clueless. Also, I compiled the executable on A and ran it on B and it worked. Note: I observed the utilized memory with Process Explorer. Question: During execution (where we have several allocations and deallocations) is it normal for the number of private bytes to be much bigger (1.5 GB vs 70 MB) than the working set?

  Read the article

• How to create a web framework in C# without ASPX?

  - by Mark

  I've managed to get a C# asp page running under ubuntu/apache/mono, but I don't want to write my framework in these ASP pages, I want to use straight C# and then I'll use a templating language for my views. But I don't know where to begin? C# is a compiled language, so... how would I do this? Would I compile everything and then have apache hook into the (single) executable and pass in the the request URL? Could I request specific .cs pages and then have apache tell it to compile and then "display" it only if it's been updated? Can the "view" files be compiled individually to avoid having to recompile everything every time there's a change? Is there some "base" I can work from, or am I going to have to reinvent accessing GET and POST variables (by reading header info) and all sorts of other stuff we take for granted in languages like PHP?

  Read the article

• App store name and info.plist

  - by user346194

  Hi guys, I've just completed my first app and having tested I'm ready for submission. However, despite numerous web searches and reading, I'm struggling to finalise the method required to enable me to have a different name on the app store to the name that appears under the app on the device home screen. In the plist.info file there is reference to bundle display name, executable name, bundle name, bundle identifier, product name etc. So, for example, say I would like the app store name to display as: HELLO WORLD and I would like the name below the icon on the device home screen to display as: HELLO How should I enter the data in the plist.info file to achieve the above? Many thanks in advance for your help. Gav.

  Read the article

• Disassemble Microsoft Visual Studio 2003 compiler output

  - by Carl Norum

  I'm seeing what I think is strange behaviour from object files output by the Microsoft Visual Studio 2003 tools. The file utility tells me: asmfile.obj: 80386 COFF executable not stripped - version 30821 For objects created by the assembler, but for objects coming from C files, I get just: cfile.obj: data Using Microsoft's dumpbin utility and the objdump I got from cygwin, I can disassemble the assembly-built file, but I get no useful results from either utility for the C-built files. I have a couple of questions related to this difference: What is the object file format generated by the MSVC2003 compiler? How can I disassemble that object file? I am particularly interested in getting the disassembly in AT&T syntax - I'm doing a port of a large source base to make it work with GCC, and I would like to use this method as a shortcut for some of the inline assembly routines in the project. Thanks!

  Read the article

• Problems Executing iPhone "GenericKeychain" Example

  - by AO

  I can't get apple's "GenericKeychain" example to run. I have replaced all 5 occurrences, as mentioned in the readme file, of "YOUR_APP_ID_HERE.com.yourcompany" with my own string: se.[company name].[project name].demo. The compilation goes fine but when trying to run it on the phone, an error saying "The executable was signed with invalid entitlements" appears. And yes, I have an ad hoc provisioning profile installed. I've tried to add "Entitlements.plist" with "get-task-allow" checked but with the same result. Has anyone been able to run the example? If that is the case, provide me with instructions on how you got it to run, please. URL: http://developer.apple.com/iphone/library/samplecode/GenericKeychain/index.html

  Read the article

• i386-mingw32-g++: error trying to exec 'cc1plus': execvp: No such file or directory

  - by Cathy

  If I compile this QT c++ program in SuSE Linux include using namespace std; int main () { cout << "Hello World!"; return 0; When I type i386-mingw32-g++ helloworld.cpp I get the following error i386-mingw32-g++: error trying to exec 'cc1plus': execvp: No such file or directory Is this because MinGW package which i installed contains only gcc in it.. hence i downloaded gcc-g++-3.4.5.rpm package and just copy pasted i386-mingw32-g++ and cc1plus executable along with C++ include files. Pls reply. Thanking You

  Read the article

• Modifying an old Windows program not to call exit after a keypress without source access

  - by rustyn2

  I have an older C++ Windows program that I've been asked to get run in a kiosk style environment for a student project. From the main menu, hitting ESC will exit the program, which is undesirable. In ye olden days I would have trapped the keyboard interrupt or whatever and dug around to NOOP whatever JMP or CALL was getting referenced in the case statement that likely decides all that, but on Windows everything goes through various registered event handlers, and I haven't done any windows internals work in about 10 years. Is there a good tool to breakpoint a program on certain WM_EVENT (WM_KEYDOWN being a prime target) messages or similar, so that I can narrow down where in the executable the check is made? I'm currently stepping back from various potential system calls made before the various thread cleanups and final exit calls but it seems like there has to be a better way to do this that I'm forgetting.

  Read the article

• Server Directory Not Accessible

  - by GusDeCooL

  I got strange things happen on live server, but normal in local server. My local server is using mac, and my live server is linux. Consider i try to access some files http://redddor.babonmultimedia.com/assets/images/map-1.jpg This work correctly. http://redddor.babonmultimedia.com/assets/modules/evogallery/check.php Return 404, I'm pretty sure my file is in there and there is no typo mistake. How come it give me 404? There is only one .htaccess on the root server and it's configuration is like this. # For full documentation and other suggested options, please see # http://svn.modxcms.com/docs/display/MODx096/Friendly+URL+Solutions # including for unexpected logouts in multi-server/cloud environments # and especially for the first three commented out rules #php_flag register_globals Off #AddDefaultCharset utf-8 #php_value date.timezone Europe/Moscow Options +FollowSymlinks RewriteEngine On RewriteBase / <IfModule mod_security.c> SecFilterEngine Off </IfModule> # Fix Apache internal dummy connections from breaking [(site_url)] cache RewriteCond %{HTTP_USER_AGENT} ^.*internal\ dummy\ connection.*$ [NC] RewriteRule .* - [F,L] # Rewrite domain.com -> www.domain.com -- used with SEO Strict URLs plugin #RewriteCond %{HTTP_HOST} . #RewriteCond %{HTTP_HOST} !^www\.example\.com [NC] #RewriteRule (.*) http://www.example.com/$1 [R=301,L] # Exclude /assets and /manager directories and images from rewrite rules RewriteRule ^(manager|assets)/*$ - [L] RewriteRule \.(jpg|jpeg|png|gif|ico)$ - [L] # For Friendly URLs RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)$ index.php?q=$1 [L,QSA] # Reduce server overhead by enabling output compression if supported. #php_flag zlib.output_compression On #php_value zlib.output_compression_level 5

  Read the article

• integrating cc.net with uppercut

  - by deepasundarip

  Hi, I installed uppercut in my system successfully, Then i installed cc.net, for automated build revision number, I followed all the steps in the following site, http://ferventcoder.com/archive/2009/05/21/uppercut---automated-builds---cruisecontrol.net-integration.aspx The same config code in that site i used to integrate but still i could find the following error when i run the cc.net svn folder Unable to execute file [D:\CodeBuild\abc\svn]. The file may not exist or may not be executable. --- System.ComponentModel.Win32Exception: The system cannot find the file specified.. Is there any different procedure to install cc.net?? I just run the exe and it said set virtual memory manually, When does the build and revision number increase?? Please help me......... I m n trouble

  Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >