Search Results

Search found 4786 results on 192 pages for 'traffic shaping'.

Page 92/192 | < Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >

• Secondary IP (eth0:0) acts like main server IP

  - by George Tasioulis

  I have a CentOS server, configured with 4 consecutive IPs: eth0 5.x.x.251 eth0:0 5.x.x.252 eth0:1 5.x.x.253 eth0:2 5.x.x.254 The problem is that all traffic goes out to the internet with eth0:0 (5.x.x.252) as the source IP, instead of eth0. # curl ifconfig.me 5.x.x.252 How can I fix this, so that all traffic goes out via eth0, ie my main IP? PS: My server is VPS running on a Xen dom0, the latter being configured in routed mode networking. Thanks in advance! Server configuration # ifconfig eth0 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.251 Bcast:5.x.x.255 Mask:255.255.255.255 inet6 addr: fe80::x:x:x:x/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14675569 errors:0 dropped:0 overruns:0 frame:0 TX packets:9463227 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4122016502 (3.8 GiB) TX bytes:25959110751 (24.1 GiB) Interrupt:23 eth0:0 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.252 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 eth0:1 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.253 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 eth0:2 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.254 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 # cat /etc/hosts 127.0.0.1 localhost.localdomain localhost 5.x.x.251 [fqdn] [hostname] # cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=static ONBOOT=yes IPADDR=5.x.x.251 NETMASK=255.255.255.224 SCOPE="peer 5.x.y.82" # cat ifcfg-eth0:0 DEVICE=eth0:0 BOOTPROTO=static ONBOOT=yes IPADDR=5.x.x.252 NETMASK=255.255.255.224 # cat route-eth0 ADDRESS0=0.0.0.0 NETMASK0=0.0.0.0 GATEWAY0=5.x.y.82 # netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 5.x.y.82 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 5.x.x.224 0.0.0.0 255.255.255.224 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 5.x.y.82 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Squid Authentication & streaming

  - by Steve Butler

  I've got squid setup using Kerberos authentication. I'm also using squidguard as an URL redirector to block out the usual nastiness of the web. There are some sites though that we allow certain users to, and others not. This all works well, assuming I'm not using any streaming. From what i can determine from the squid logs and the wireshark traces I've done, when the initial request to stream is sent, everything is good, the authenticated username is sent with the request to squidguard. The problem is that on subsequent traffic the username is not sent to squidguard, causing it to be blocked based on default policy. I've tried using the squid built-in allow/deny stuff, but its relatively clunky, and so far squidguard has been pretty easy and fast. Here comes the question(s): How do i get Squid to pass username on all requests? (something tells me this isn't the best way) How do i get squidguard to see traffic is authenticated to a specific user even when a username isn't passed? Is there any other way of accomplishing this? A few details that may be of importance: I'm using a list of users stored in a text file for squidguard to compare against. I'm using full kerberos auth with Squid. CentOS 6.0 Squid 3.1.4 Squidguard 1.3

  Read the article

• Apache2 - 500 internal server error

  - by Lucio Coire Galibone

  i'm running a VPS with Linux CentOs 6 with 4 GB of RAM, 10 GB of HD and 2 virtual CPU Intel(R) Xeon(R)CPU L5640 @ 2.27GHz. As my host says each virtual CPU must be at least 0.5 physical cpu. At certain times of the day, those with more traffic, trying accessing my php script i receive intermittently "500 internal server error". I activate logging to debug level from apache, and also the PHP logging with E_ALL, but I can't find reference to Error 500 in any logs(I checked the right logs!). I haven't got any .htaccess file in path script. The strange thing is that the error start at first php line in the script (the previous html displays correctly, but at the first php line the script send 500 error). The cpu load is always good (max 0.15 0.08 0.01) and RAM is close to 95% but it arrived to swap just 2 times in a month with 2-5 MB. Apache works with prefork with this values: <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 280 MaxClients 280 MaxRequestsPerChild 4000 </IfModule> Everthing works correctly and I don't get any error in quiet times, but i start receive errors when traffic rises (6-9000 visits per hour). Can i solve the problem increasing resources? (i can upgrade RAM up to 16 GB). It can depend from reaching MaxClients (but apache must write it on log, right?)? If I upgrade RAM to 6 or 8 GB i have to calculate MaxClients value with this? MaxClients = Total RAM dedicated to the web server / Max child process size Max child process size is around 20M. How else can the problem be? Thanks in advance

  Read the article

• How do I determine the cause of a sustained spike in mysql queries/activity?

  - by mattmcmanus

  So this is more of a "I'm trying to learn about how this works" question rather than "there is a serious problem I can't figure out!" question. I'm setting up a VPS and have been tweaking and changing things here and there. I recently installed munin (like two days ago) and yesterday I noticed a significant increase in mysql activity. So now my curiosity is going crazy. How do I setup/access mysql's query log? I have about 5 databases on the server so I want to see which one is getting all the action. Is there anything else I can do to keep a better eye on what's going on? Here are the graphs. As you can tell, it's not that much activity at all but I'm just curious at the change. The sites that are on the server right now do not get a lot of traffic. It's running a couple drupal sites, only one of which is live. The live one hasn't had a spike in traffic and the last spike was 250 visitors so it's barely a spike at all.

  Read the article

• NAT ports - how do they work?

  - by Davidoper

  I have the following network schema: Computer A: three nics: NIC 1 (eth0): dhcp, public internet NIC 2 (eth1): static 192.168.1.1, gateway for Computer B NIC 3 (eth2): static 192.168.2.1, gateway for Computer C Computer B: static 192.168.1.2, using gateway 192.168.1.1 (NIC 2). Computer C: static 192.168.2.2, using gateway 192.168.2.1 (NIC 3). So I applied this to get NAT working: iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE Every computer can connect to the internet now. I have been applying rules to the main computer (Computer A), like dropping connections to some ports, e.g ssh: iptables -A INPUT -p tcp --dport 22 -j DROP But for instance, now I would like only allow connections for ports 20,21,22,53 and 80 in Computer C, and ignore the outside traffic if it's not related to those ports. The allowed connections should be FROM Computer C to outside, but not from outside to Computer C (I mean - Computer C is not hosting any HTTP or SSH, but it is going to use them as a client). I guess this sould be done like this: iptables -A OUTPUT -i eth2 -o eth0 -p tcp --dport 21 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth2 -o eth0 -p tcp --sport 21 -m state --state ESTABLISHED -j ACCEPT The last rule (dropping any other traffic different from those) is at the end of the configuration, so -A should be working correctly. The thing is... it is not working. If I put the last rule like this: iptables -A FORWARD -i eth2 -o eth0 -j DROP It just drops everything and, for instance, port 21 (previously opened as you can see above) is not either working. Can you tell me what could I have done wrong? I have been struggling with this problem for some time and I am unable to solve it. Thanks!

  Read the article

• IPTables: NAT multiple IPs to one public IP

  - by Kaemmelot

  I'm looking for a way how to nat 2 or more inner IPs (in my case xen doms) to one outer IP. I tried to use iptables -t nat -A PREROUTING -d 123.123.123.123 -j DNAT --to 1.2.3.4 --to 1.2.3.7 iptables -t nat -A POSTROUTING -s 1.2.3.4 -j SNAT --to 123.123.123.123 iptables -t nat -A POSTROUTING -s 1.2.3.7 -j SNAT --to 123.123.123.123 And got an error: iptables v1.4.14: DNAT: Multiple --to-destination not supported Try `iptables -h' or 'iptables --help' for more information. I found this in the manpage: Later Kernels (= 2.6.11-rc1) don't have the ability to NAT to multiple ranges anymore. So my question is: Why is it not possible anymore and is there a workaround? Maybe I should use an other method I don't know yet? EDIT: The idea is to use the system like a router, so I have one address but multiple users behind. The problem is I don't know which connection reffers to a user (for example 1.2.3.4). But I know, they all have different ports open for incomming traffic. So my solution (for DNAT) would be to nat all incoming connections to all users and filter all unused ports, so the connection goes to one single user. For outgoing traffic I would use iptables -A FORWARD -i eth0 -d 1.2.3.4 -m state --state ESTABLISHED,RELATED -j ACCEPT

  Read the article

• Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

  - by Bo102010

  (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

  Read the article

• KVM guest VLAN aware problems

  - by baraka

  Hi, We are using Centos 5.5. as KVM host. It has two nics. One for management and the other one for services. As we have services in multiple vlans this nic is configured as a 802.1Q trunk. Any VM must be able to have access to any vlan, so host trunk interface is bridged to its tap interface and vlan is configured inside VM. Everything works fine while there is not heavy traffic. I can not find any log on guest or host, but, after some certain sustained big file transfer (about 6Gb) bridging stop working. Other guest on the same host continue working without problems. tcpdump on bridge interface is Ok, but on guest tap inferface I can see only outgoing traffic. Restarting bridge or rejoining tap interface doesn't provide any clue. Rebooting guest turns on bridge again. Bridge configuration is minimal: just addbr and addif (no stp). Any idea welcome!

  Read the article

• Changing Mac OS X 10.6 Routing after VPN'd In

  - by Matt Rogish

  I have a coffee shop around the corner that I use to do some work when I want to get away from home. They offer free wi-fi and I then use my Mac 10.6 VPN to log into my work network. I have "Send all traffic over VPN connection" checked. Before, their network was 10.0.0.x. I think they got a new router because it's now 192.168.2.x However, this interferes with one of the subnets at work so now I can't visit 192.168.2.x at work. So: 1) Office network: VPN gives IPs as 192.168.1.x. Another network is 192.168.2.x 2) Coffee network: Gives IPs as 192.168.2.x I think if I set a route to send all 2.x traffic over the tunnel, it would blow up my routing to their system, right? What should I do? I know the individual IPs of the servers I want... Maybe I could add each one, or can I add all of them minus the default gateway of their router? How do I set that up "temporarily" in my Mac? Thanks!!

  Read the article

• Possible to IPSec VPN Tunnel Public IP Addresses?

  - by caleban

  A customer uses an IBM SAS product over the internet. Traffic flows from the IBM hosting data center to the customer network through Juniper VPN appliances. IBM says they're not tunneling private IP addresses. IBM says they're tunneling public IP addresses. Is this possible? What does this look like in the VPN configuration and in the packets? I'd like to know what the source/destination ip/ports would look like in the encrypted tunneled IPSec Payload and in the IP packet carrying the IPSec Payload. IPSec Payload: source:1.1.1.101:1001 destination:2.2.2.101:2001 IP Packet: source:1.1.1.1:101 destination:2.2.2.1:201 Is it possible to send public IP addresses through an IPSec VPN tunnel? Is it possible for IBM to send a print job from a server on their network using the static-nat public address over a VPN to a printer at a customer network using the printer's static-nat public address? Or can a VPN not do this? Can a VPN only work with interesting traffic from and to private IP addresses?

  Read the article

• VMware Server Host-Only Network Routing

  - by Chris

  I have a windows 2008 web server machine running VMware server. I have 3 VM's - All 3 are test servers so security isn't really a concern... each of them running windows 2008 standard and some of them serving web content. My ISP only allows one MAC address to access the physical switch, however they give me 10 public IP addresses to use. My question is, if I put each VM on their own Host only network, how can I route all traffic from a specific public IP on the host, to the corresponding host only adapter, therefore routing to the specific VM? For example: A single physical Adapter on the Host has the following public IP's assigned to it in windows networking: 74.208.14.10 74.208.14.20 74.208.14.30 Each VM is on a host-only network vm1 - 192.168.196.1 vm2 - 192.168.197.1 vm3 - 192.168.198.1 On the host, I want to route all traffic from 74.208.14.10 to VM1 and 74.208.14.20 to VM2 and 74.208.14.30 to vm3 without using VMware NAT, or bridged connections. I want each server to appear to have its own public IP address. My guess is i can modify the route tables somehow, or perhaps in ICS...but i'm not sure how.

  Read the article

• MS SQL Server Firewall Ports

  - by mmacaulay

  Hi, I've recently found myself in the position of quickly deploying a production app on SQL Server 2008 (EXPRESS), and I've been having some issues with configuring firewall rules between our web server running the ASP.NET app and our database server. Everything that I can find on the internet claims that I should only need to have TCP ports 1433/1434 and UDP port 1434 accessible on the database server. However, we were unable to get connectivity going between the web app and the database with just those ports. With the help of one of the guys in our datacentre, we discovered that there was traffic also going to TCP port 2242 on the database server. After opening this port, everything worked, but we're not sure why. Later on, I had to reinstall SQL Server due to some disk space issues, and found that the problem had resurfaced - after another session with the packet sniffer, we discovered that this time traffic was going to TCP port 4541 on the database server. My question is, is there some configuration option that I'm missing in SQL server that's making it choose random ports? I'd like to have our firewall rules locked down as much as possible, and of course we'd like to avoid any future mysterious connectivity issues, especially once the app is live. Both servers are running Windows 2003 R2 X64.

  Read the article

• Amazon VPC NAT not working

  - by rpkelly

  I'm trying to create a NAT instance for my VPC to allow instances on private subnets connect to the internet (most importantly, S3). I tried following the instructions here: http://docs.amazonwebservices.com/AmazonVPC/2011-07-15/UserGuide/index.html?VPC_NAT_Instance.html . Unfortunately, the instances in the private subnet (call it 10.10.2.0/24) cannot reach the internet. I have done the following: Create a NAT instance (Amazon's ami-vpc-nat-1.0.0-beta.i386-ebs (ami-d8699bb1)) in public subnet (call it 10.10.1.0/24). Changed "Source / Dest Check" to disabled. Created a new entry in the default routing table (which is used by 10.10.2.0/24) and had it point to the ID of the newly created instance. Associated an Elastic IP address with the NAT instance. Allowed all outbound traffic on the security group of the NAT instance. Ensured that all traffic could pass between the two subnets. I've tried also doing this with an existing instance using iptables, but had no luck. And I have verified that sys.net.ipv4.ip_forward is 1, just in case anyone was wondering. And I still have no internet connectivity from the instances on 10.10.2.0/24. Does anyone have any suggestions?

  Read the article

• FreeBSD slow transfers - RFC 1323 scaling issue?

  - by Trey

  I think I may be having an issue with window scaling (RFC 1323) and am hoping that someone can enlighten me on what's going on. Server: FreeBSD 9, apache22, serving a static 100MB zip file. 192.168.18.30 Client: Mac OS X 10.6, Firefox 192.168.17.47 Network: Only a switch between them - the subnet is 192.168.16/22 (In this test, I also have dummynet filtering simulating an 80ms ping time on all IP traffic. I've seen nearly identical traces with a "real" setup, with real internet traffic/latency also) Questions: Does this look normal? Is packet #2 specifying a window size of 65535 and a scale of 512? Is packet #5 then shrinking the window size so it can use the 512 scale and still keep the overall calculated window size near 64K? Why is the window scale so high? Here are the first 6 packets from wireshark. For packets 5 and 6 I've included the details showing the window size and scaling factor being used for the data transfer. Code: No. Time Source Destination Protocol Length Info 108 6.699922 192.168.17.47 192.168.18.30 TCP 78 49190 http [SYN] Seq=0 Win=65535 Len=0 MSS=1460 WS=8 TSval=945617489 TSecr=0 SACK_PERM=1 115 6.781971 192.168.18.30 192.168.17.47 TCP 74 http 49190 [SYN, ACK] Seq=0 Ack=1 Win=65535 Len=0 MSS=1460 WS=512 SACK_PERM=1 TSval=2617517338 TSecr=945617489 116 6.782218 192.168.17.47 192.168.18.30 TCP 66 49190 http [ACK] Seq=1 Ack=1 Win=524280 Len=0 TSval=945617490 TSecr=2617517338 117 6.782220 192.168.17.47 192.168.18.30 HTTP 490 GET /utils/speedtest/large.file.zip HTTP/1.1 118 6.867070 192.168.18.30 192.168.17.47 TCP 375 [TCP segment of a reassembled PDU] Details: Transmission Control Protocol, Src Port: http (80), Dst Port: 49190 (49190), Seq: 1, Ack: 425, Len: 309 Source port: http (80) Destination port: 49190 (49190) [Stream index: 4] Sequence number: 1 (relative sequence number) [Next sequence number: 310 (relative sequence number)] Acknowledgement number: 425 (relative ack number) Header length: 32 bytes Flags: 0x018 (PSH, ACK) Window size value: 130 [Calculated window size: 66560] [Window size scaling factor: 512] Checksum: 0xd182 [validation disabled] Options: (12 bytes) No-Operation (NOP) No-Operation (NOP) Timestamps: TSval 2617517423, TSecr 945617490 [SEQ/ACK analysis] TCP segment data (309 bytes) Note: originally posted http://forums.freebsd.org/showthread.php?t=32552

  Read the article

• SCM8014 to FVS338

  - by Jack

  I have a SMC8014 Router/Modem that Comcast provided me with their business class service. It was not filtering malicious traffic as aggressively as I had hoped, so I purchased a NetGear ProSafe FVS338, and put this behind the SMC8014, and all my machines behind that. After some brief configuration, all machines can see out to the internet. I also have a single web server, and I have not been able to configure things so that incoming requests can reach it. This is where I need help! I would like to have the FVS339 do NAT, so that I can assign a 192.168 address to my webserver. I've tried everything I know of, and I can't get things going. I set the SMC8014 to have a LAN facing IP of 10.0.0.1, and I assigned the FVS339 a WAN facing IP of 10.0.0.2. I would like to be able to tell the SMC8014 to just forward all traffic to 10.0.0.2, but I haven't had any success. In my (unfortunately limited) understanding, what I probably want here is a static route, but I don't know how to cofigure one, or if this is really what I want. The SMC8014 wants a Destination IP, a Subnet Mask and a Gateway IP. Any help would be appreciated.

  Read the article

• Internet slowed down because of SQUID Server setup

  - by Ranjith Kumar

  Recently I have setup a squid server for our office. I have computer (A) with two ethernet cards, one for internet and the second one for local networkIt has Ubuntu server OS with squid-server and dhcp3-server installedI have added few iptable rules to work like a router and redirect all http traffic to 3128 port This link is my reference. Everything worked fine for 2 days. All of a sudden internet speed went down drastically. When I connected the internet cable to my laptop to test the internet speed it was fine. Again when I reconnected it back to computer A everything was normal. This happened 4 times in a week. Could anyone here please help me why the internet speed is going down and it becomes normal when I reconnect the cable. EDIT: Rebooting the system (computer A) didn't make a difference. I have changed iptables so that http traffic doesn't redirect to 3128 port any further, still no change in the internet speed. I think the problem is not with squid but with something else. Here are my iptable rules SQUID_SERVER="10.1.1.1" INTERNET="eth1" LAN_IN="eth0" SQUID_PORT="3128" PROXYSERVERS=(Atlanta Baltimore Boston Chicago Dallas Denver Houston KansasCity LosAngeles Miami NewYork Philadelphia Phoenix SanAntonio SanDiego SanJose Seattle Washington) SERVERLEN=${#PROXYSERVERS[*]} I=0 iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X modprobe ip_conntrack modprobe ip_conntrack_ftp echo 1 /proc/sys/net/ipv4/ip_forward iptables -P INPUT DROP iptables -P OUTPUT ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A OUTPUT -o lo -j ACCEPT iptables -A INPUT -i $INTERNET -m state --state ESTABLISHED,RELATED -j ACCEPT iptables --table nat --append POSTROUTING --out-interface $INTERNET -j MASQUERADE iptables --append FORWARD --in-interface $LAN_IN -j ACCEPT iptables -A INPUT -i $LAN_IN -j ACCEPT iptables -A OUTPUT -o $LAN_IN -j ACCEPT while [ $I -lt $SERVERLEN ]; do iptables -t nat -A PREROUTING -i $LAN_IN -p tcp -d ${PROXYSERVERS[$I]}.wonderproxy.com --dport 80 -j ACCEPT let I++ done iptables -t nat -A PREROUTING -i $LAN_IN -p tcp --dport 80 -j DNAT --to $SQUID_SERVER:$SQUID_PORT iptables -A INPUT --protocol tcp --dport 80 -j ACCEPT iptables -A INPUT --protocol tcp --dport 443 -j ACCEPT iptables -A INPUT --protocol tcp --dport 22 -j ACCEPT iptables -A INPUT -j LOG iptables -A INPUT -j DROP

  Read the article

• Wireless Activity Monitoring for PCI DSS Compliance

  - by dkusleika

  In an effort to be PCI DSS compliant, I took a trustkeeper.net questionnaire. I failed the question that asks Is the presence of wireless access points tested for by using a wireless analyzer at least quarterly or by deploying a wireless IDS/IPS to identify all wireless devices in use? (SAQ #11.1) My only wireless access point is outside my firewall, so even if you cracked my wireless you couldn't get inside my domain (unless you crack that too). My firewall doesn't have IPS and I couldn't tell if it had IDS. I looked around for a wireless analyzer, but what I found was $500, which is a little pricey for my size business. And even if I got it, I'm not sure I would understand what it tells me. Surely there are smaller/less sophisticated businesses that take credit cards and have solved this. My questions are: What are the risks if someone were to crack my wireless? (Could they read all internet traffic? Just wireless traffic? Just use my internet connection?) And what is the best/cheapest way to test my connection point quarterly? Should I buy the $500 analyzer? Domain is Windows Server 2000. Firewall is Sonicwall Pro 2040. Router is 8 port D-link.

  Read the article

• How to setup Mac server to use two gateways

  - by Brady

  I recently asked this question: How to set Mac server to use different Gateway for internet bound traffic The answer given works but has presented me with another issue that I didnt make clear in that question. Here is my network layout as it stands: At the moment outside staff members use some services on the existing internet 1 link. Those services are hosted by the Mac server. If I change the gateway of the Mac server to the second modem those outside staff lose visabilty on those services. Now I dont know how to go about solving this issue. I want the second link to be used when the Mac server goes to rsync data offsite but everything else use link one. How do I do this? Thanks Scott EDIT: This has been resolved by setting the default gateway on the Mac server to 192.168.1.254 Thus leaving everything on the network as it was before. but to get the Mac server to use the other link for rsync I've added a route to the Mac server to route traffic to the rsync server through the second gateway. sudo route add -net {server IP's}/{Netmask} 192.168.1.1 I've awarded the answer to gravyface for pointing me to a post on how to make this route persistant in Mac

  Read the article

• Widespread misinterpretation of DNS rules in resolving wildcards

  - by Dominic Sayers

  [EDITED to add: This problem has gone away on its own. I believe Cloudflare's name resolution may have been to blame. See my own answer below] Here is a snippet of my zone file *.example.com. 300 IN CNAME proxy.herokuapp.com. foo.example.com. 300 IN A 111.111.111.111 If I dig @8.8.8.8 foo.example.com I get the answer I expect: ;; ANSWER SECTION: foo.example.com. 30 IN A 111.111.111.111 The same is true of all other public DNS servers I've tried. However, when I try to set up a check with Pingdom to a URL on foo.example.com it instead sends the traffic to my Heroku app referenced by the *.example.com RR. The same is true of checks set up on New Relic, Errplane and traffic generated by the Heroku app itself. So on the one side, all public DNS servers interpret the zone file one way. Yet four service providers all interpret it a different way, one that differs to the standard suggested by RFC 4592. My question is: are these reputable, mature service providers all wrong? Or is it little me?

  Read the article

• Using IIS7 as a reverse proxy

  - by Eric Petroelje

  I'm setting up a server at home to host a few small websites. One of them is .NET based and needs IIS, the others are PHP based and need Apache. So, I have both IIS 7 and Apache 2.2.x installed on my server with IIS on port 80 and Apache running on port 8080. I would like to set up IIS to work as a reverse proxy, forwarding the requests for the Apache sites to port 8080 and serving the requests for the .NET site itself based on the host headers. Like this: www.mydotnetsite.com/* -> IIS -> serve from IIS www.myapachesite.com/* -> IIS -> forward to apache on port 8080 www.myothersite.com/* -> IIS -> forward to apache on port 8080 I did a bit of googling and it seemed like the Application Request Routing feature would do what I needed, but I can't seem to get it to work the way I want it to. I can get it to forward ALL traffic to the Apache server and I can get it to forward traffic with a specific URL pattern to the Apache server, but I can't seem to get it to forward based on the host headers (e.g. "forward all requests for www.apachesite.com - localhost:8080") So the question is, how would I go about configuring ARR to do this? Or do I need a different tool? I'm also open to using Apache as the reverse proxy and forwarding the .NET site requests to IIS instead if that's easier (running Apache on port 80 and IIS on 8080).

  Read the article

• SQL Server 2008 Web VS SQL Server 2008 Enterprise

  - by Jeremy

  I wrote an application a few months ago, and was hosting it out of our offices on a workstation with an Intel Core 2 Quad Q8200 @ 2.33GHz, 8 GB RAM, Windows Server 2008 Enterprise and SQL Server 2008 Enterprise. Both the webserver and database server were run on the same machine. We had a huge influx in traffic, and moved ClubUptime.com, and got 2 of their top teir windows VMs. The Database server runs Windows 2008 R2 Standard and SQL Server 2008 R2 Web on 8 GB ram and an Intel Xeon e5620 @ 2.40GHz. Ever since switching, the database which used to run at around 400MB in RAM now runs at around 4-7GB, and there haven't been any changes to it (other than a couple columns here and there). Our traffic has quadrupled, and our DB is 6 GB on disk, why would SQL server take up 7 GB if the DB is only 6. And why would it be storing the ENTIRE database in memory? Another thing is why growing 4 times in size did the database's memory footprint grow 12 times? Last question: Why does the CPU peg at 100% now where it didn't before? The design is simple, VERY few joins, NO subqueries. I am just at a loss, unless it is the SQL server edition, or the fact that I moved from real hardware to a VM.

  Read the article

• Spammer relaying via Postfix mail server

  - by Paddington

  I have a Plesk 9.5 mail server (cm.snowbarre.co.za) on Ubuntu 8.04 LTS which forwards all SMTP traffic to an anti-spam server cacti.snowbarre.co.za. Many times I see the headers on the anti-spam server to contain from addresses not hosted on the mail server and I have checked and confirmed that my server is not an open relay server. How can a spammer be using my server to relay spam traffic? How can I stop this? Open relay test: paddington@paddington-MS-7387:~$ telnet cm 25 Trying 196.201.x.x... Connected to cm. Escape character is '^]'. 220 cm.snowbarre.co.za ESMTP Postfix (Ubuntu) mail from:[email protected] 250 2.1.0 Ok rcpt:[email protected] 221 2.7.0 Error: I can break rules, too. Goodbye. Connection closed by foreign host. paddington@paddington-MS-7387:~$ A typical headers is: *Received from cm.snowbarre.co.za (cm.snowbarre.co.za[196.201.x.x]) by cacti.snowbarre.co.za (Postfix) with ESMTPS id 00B601881AD; Mon, 27 Aug 2012 14:03:29 +0200 (SAST) Received from cm.snowbarre.co.za (localhost [127.0.0.1]) by cm.snowbarre.co.za (Postfix) with ESMTP id 81627367E007; Mon, 27 Aug 2012 14:02:50 +0200 (SAST) Received from User (ml82.128.x.x.multilinksg.com [82.128.x.x]) by cm.snowbarre.co.za (Postfix) with ESMTP; Mon, 27 Aug 2012 14:02:49 +0200 (SAST) Reply-To <[email protected]> From "Ms Nkeuri Aguiyi"<[email protected]> Subject Your Unpaid Fund. Date Mon, 27 Aug 2012 05:03:22 -0700 MIME-Version 1.0 Content-Type text/html; charset="Windows-1251" Content-Transfer-Encoding 7bit X-Priority 3 X-MSMail-Priority Normal X-Mailer Microsoft Outlook Express 6.00.2600.0000 X-MimeOLE Produced By Microsoft MimeOLE V6.00.2600.0000 X-Antivirus avast! (VPS 120821-0, 08/21/2012), Outbound message X-Antivirus-Status Clean Message-Id <[email protected]> To undisclosed-recipients:;*

  Read the article

• How do I create a wifi network bridge with qemu on OS X?

  - by a paid nerd

  I grabbed a small FreeBSD live CD and QEMU, and I'm trying to bridge my Mac OS X 10.8 wifi connection so that the guest OS is available on my LAN. However, the guest OS never gets a DHCP lease. This works perfectly with VirtualBox in their "bridged" network mode, so I know it can be done. I need to get it working with QEMU because VirtualBox doesn't support the architecture that I need for this project. Here's what I've done so far based on hours of googling: Installed TUNTAP for OS X Told OS X to supposedly forward all packets, even ARP: (NOTE: This doesn't appear to work.) $ sudo sysctl -w net.inet.ip.forwarding=1 $ sudo sysctl -w net.link.ether.inet.proxyall=1 $ sudo sysctl -w net.inet.ip.fw.enable=1 Created a bridge: $ sudo ifconfig bridge0 create $ sudo ifconfig bridge0 addm en0 addm tap0 $ sudo ifconfig bridge0 up $ ifconfig bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether ac:de:xx:xx:xx:xx Configuration: priority 0 hellotime 0 fwddelay 0 maxage 0 ipfilter disabled flags 0x2 member: en0 flags=3<LEARNING,DISCOVER> port 4 priority 0 path cost 0 member: tap0 flags=3<LEARNING,DISCOVER> port 8 priority 0 path cost 0 tap0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether ca:3d:xx:xx:xx:xx open (pid 88244) Started tcpdump with -I in the hopes that it enables promiscuous mode on the wifi device: $ sudo tcpdump -In -i en0 Run QEMU using the bridged network instructions: $ qemu-system-x86_64 -cdrom mfsbsd-9.2-RELEASE-amd64.iso -m 1024 \ -boot d -net nic -net tap,ifname=tap0,script=no,downscript=no But the guest system never gets a DHCP lease: If I tcpdump -ni tap0, I see lots of traffic from the wireless network. But if I tcpdump -ni en0, I don't see any DHCP traffic from the QEMU guest OS. Any ideas? Update 1: I tried sudo defaults write "/Library/Preferences/SystemConfiguration/com.apple.Boot" "Kernel Flags" "net.inet.ip.scopedroute=0" and rebooting per this mailing list suggestion, but this didn't help. In fact, it made VirtualBox bridged mode stop working.

  Read the article

• ntop to analyse bandwidth usage on multiple ASA 5505

  - by dunxd

  I have set up a netflow server at our data centre, which is connected via VPN to ~40 remote offices using Cisco ASA 5505. The aim is to analyse usage data and find out exactly how the remote connections are being used. I followed through http://techowto.files.wordpress.com/2008/09/ntop-guide.pdf to set up ntop and https://supportforums.cisco.com/docs/DOC-6114 to set up the ASAs. I can see from the Plugin Netflow Statistics page that netflow packets from my ASAs are being received - the counter is increasing. However, I am not seeing any breakdown on the Global Traffic Statistic page after switching to the Netflow interface. I'm just seeing a pie chart showing 100% traffic for eth0. The interfaces and documentation are a little hard to follow so I am not sure I have got things configured correctly. When setting up my NetFlow-device.2 I can specify Virtual NetFlow Interface Network Address - the web UI says This value is in the form of a network address and mask on the network where the actual NetFlow probe is located. is this a Network address (e.g. 192.168.0.0/24) or an actual host IP address (192.167.0.1/24)? If that should be a network address, is this the network in which one of my ASAs is or the network in which my ntop server is? If a host IP address, is this the IP address used by eth0 on my ntop server, the IP address of an ASA, or something else? Do I need a separate virtual interface for each ASA I am collecting netflow data from? Any guidance would be greatly welcome.

  Read the article

• How to set minimum SQL Server resource allocation for a database?

  - by Jeff Widmer

  Over the past Christmas holiday week, when the website I work on was experiencing very low traffic, we saw several Request timed out exceptions (one on each day 12/26, 12/28, 12/29, and 12/30) on several pages that require user authentication. We rarely saw Request timed out exceptions prior to this very low traffic week. We believe the timeouts were due to the database that it uses being "spun down" on the SQL Server and taking longer to spin up when a request came in. There are 2 databases on the SQL Server (SQL Server 2005), one which is specifically for this application and the other for the public facing website and for authentication; so in the case where users were not logged into the application (which definitely could have been for several hours at a time over Christmas week) the application database probably received no requests. We think at this point SQL Server reallocated resources to the other database and then when a request came in, extra time was needed to spin up the application database and the timeout occurred. Is there a way to tell SQL Server to give a minimum amount of resources to a database at all times?

  Read the article

< Previous Page | 88 89 90 91 92 93 94 95 96 97 98 99  | Next Page >