Search Results

Search found 2415 results on 97 pages for 'asus motherboard'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 93/97 | < Previous Page | 89 90 91 92 93 94 95 96 97  | Next Page >

  • XenServer 6.0.2 path to installation media contains non-ascii characters

    - by cmaduro
    XenServer 6.0.2 install fails no matter what I do. I have confirmed that the md5 checksum on my ISO file is good. I tried installing from a mounted ISO file (remotely via iKVM). I tried installing from physical media. I tried installing from a bootable USB stick (using syslinux + contents of the ISO) All attempts have yielded the same result: When verifying the installation media, at 0% initializing, the following is reported: "Some packages appeared to be damaged." followed by a list of pretty much all the gz2 and rpm packages. If I skip the media verification the installer proceeds and then gives me an error when it reaches "Installing from base pack" at 0% which states "An unrecoverable error has occurred. The error was: 'ascii' codec can't decode byte 0xff in position 20710: ordinal not in range(128) Please refer to your user guide, or contact a Technical Support Representative, for further details" there is one option left which is to reboot. Apparently at some point during the processing of the repositories on the installation media non-ascii characters are found, which causes the installer to quit. How do I fix this? Here are my specs TYAN S8236 motherboard 2 AMD Opteron 6234 processors LSI2008 card connected to 2 1TB Seagate Constellation drives SATA, 1 500GB Corsair m4 SSD SATA and 1 Corsair Forse 3 - 64GB SSD SATA Onboard SATA connected to a slim DVD-+RW. Onboard SAS connected to 2 IBM ESX 70GB 10K SAS drives (for XenServer) 256GB memory ================================================================================= Comments: According to pylonsbook.com "chances are you have run into a problem with character sets, encodings, and Unicode" – cmaduro 10 hours ago A clue is provided by "vmware.com/support/vsphere5/doc/…; Data migration fails if the path to the vCenter Server installation media contains non-ASCII characters When this problem occurs, an error message similar to: 'ascii' codec can't decode byte 0xd0 in position 30: ordinal not in range(128) appears, and the installer quits unexpectedly during the data migration process. – cmaduro 10 hours ago This is an error that python throws. And guess what, the .py extention of the file you have to edit in this link community.spiceworks.com/how_to/show/1168 means the installer is written in python. Python is interpreted, so now to find the install file responsible for this error. – cmaduro 6 hours ago The file that generates the error upon verification is /opt/xensource/installer/tui/repo.py. The error message appears around line 359. – cmaduro 2 hours ago I am fairly sure that the install error is generated somewhere in repository.py as the backend.py file throws errors while methods in that file are being called. Perhaps all errors can be traced back to this file. – cmaduro 1 hour ago

    Read the article

  • Using a 64bit Linux kernel, can't see more than 4GB of RAM in /proc/meminfo

    - by Chris Huang-Leaver
    I'm running my new computer which has 8GB of RAM installed, which is visable from BIOS page, does not show in /proc/meminfo uname -a Linux localhost 3.0.6-gentoo #2 SMP PREEMPT Sat Nov 19 10:45:22 GMT-- x86_64 AMD Phenom(tm) II X4 955 Processor AuthenticAMD GNU/Linux The result of /proc/meminfo is as follows: (thans Andrey) MemTotal: 4021348 kB MemFree: 1440280 kB Buffers: 23696 kB Cached: 1710828 kB SwapCached: 4956 kB Active: 1389904 kB Inactive: 841364 kB Active(anon): 1337812 kB Inactive(anon): 714060 kB Active(file): 52092 kB Inactive(file): 127304 kB Unevictable: 32 kB Mlocked: 32 kB SwapTotal: 8388604 kB SwapFree: 8047900 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 492732 kB Mapped: 47528 kB Shmem: 1555120 kB Slab: 267724 kB SReclaimable: 177464 kB SUnreclaim: 90260 kB KernelStack: 1176 kB PageTables: 12148 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 10399276 kB Committed_AS: 3293896 kB VmallocTotal: 34359738367 kB VmallocUsed: 317008 kB VmallocChunk: 34359398908 kB AnonHugePages: 120832 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 2048 kB DirectMap4k: 23552 kB DirectMap2M: 3088384 kB DirectMap1G: 1048576 kB I have tried using mem=8G as a kernel boot parameter, I read a post about setting HIGHMEM64G to yes, before realising that only applies to 32bit kernels. Trying dmindecode -t memory SMBIOS 2.7 present. Handle 0x0026, DMI type 16, 23 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: Multi-bit ECC Maximum Capacity: 32 GB Error Information Handle: Not Provided Number Of Devices: 4 Handle 0x0028, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM0 Bank Locator: BANK0 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer0 Serial Number: SerNum0 Asset Tag: AssetTagNum0 Part Number: Array1_PartNumber0 Rank: Unknown Handle 0x002A, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM1 Bank Locator: BANK1 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer1 Serial Number: SerNum1 Asset Tag: AssetTagNum1 Part Number: Array1_PartNumber1 Rank: Unknown Handle 0x002C, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: 64 bits Data Width: 64 bits Size: 4096 MB Form Factor: DIMM Set: None Locator: DIMM2 Bank Locator: BANK2 Type: <OUT OF SPEC> Type Detail: Synchronous Speed: 1333 MHz Manufacturer: Manufacturer2 Serial Number: SerNum2 Asset Tag: AssetTagNum2 Part Number: Array1_PartNumber2 Rank: Unknown Handle 0x002E, DMI type 17, 34 bytes Memory Device Array Handle: 0x0026 Error Information Handle: Not Provided Total Width: Unknown Data Width: 64 bits Size: No Module Installed Form Factor: DIMM Set: None Locator: DIMM3 Bank Locator: BANK3 Type: Unknown Type Detail: Synchronous Speed: Unknown Manufacturer: Manufacturer3 Serial Number: SerNum3 Asset Tag: AssetTagNum3 Part Number: Array1_PartNumber3 Rank: Unknown

    Read the article

  • Can't detect wireless networks, running ubuntu 9.10 on eeepc 1000he

    - by David Brown
    Hi, I am running Ubuntu 9.10 on an ASUS eeepc 1000HE, and my wireless card, RaLink RT 2860, is failing to recognize any wireless networks. It was working fine this morning, until I accidentally hit Fn F2, disabling the wireless card. I hit Fn F2 again to reenable it, but it no longer will detect any wireless networks (and other computers in the household do recognize them). Any help at all will be greatly appreciated! I googled quite a bit and talked to a human about this but could not fix it. We tried dhclient ra0, which returned There is already a pid file /var/run/dhclient.pid with pid 2438 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.2 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ Listening on LPF/ra0/00:25:d3:13:f4:20 Sending on LPF/ra0/00:25:d3:13:f4:20 Sending on Socket/fallback DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 9 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 10 DHCPDISCOVER on ra0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. No working leases in persistent database - sleeping. Other data: iwconfig returns (other stuff here...) ra0 RT2860 Wireless ESSID:"" Nickname:"RT2860STA" Mode:Auto Frequency=2.412 GHz Bit Rate=1 Mb/s RTS thr:off Fragment thr:off Link Quality=10/100 Signal level:0 dBm Noise level:-87 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ifconfig returns (other stuff here...) ra0 Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet6 addr: fe80::225:d3ff:fe13:f420/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:583 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:19 ra0:avahi Link encap:Ethernet HWaddr 00:25:d3:13:f4:20 inet addr:169.254.7.117 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 Interrupt:19

    Read the article

  • Low framerate on background apps

    - by user1698923
    My problem is that when a game is running in the foreground, in Full Screen mode, any applications on my second monitor (such as youtube videos, videos, not app specific) drop their frame-rate to about 2-3 FPS. It seems like some sort of power management option that I can't track down. As far as I can tell, it's not due to the GPU not being able to keep up. For instance, my PC can play League of Legends at about 280FPS when the framerate is uncapped. If i cap it at 60FPS using the in-game option, it has no affect on the performance of the background app. Summary Operating System Windows 8 Pro 64-bit CPU Intel Core i7 3820 @ 3.60GHz 42 °C Sandy Bridge-E 32nm Technology RAM 12.0GB Triple-Channel DDR3 @ 533MHz (7-7-7-20) Motherboard Gigabyte Technology Co., Ltd. X79-UD3 (SOCKET 0) 37 °C Graphics DELL U2713HM (2560x1440@59Hz) DELL U2713HM (2560x1440@59Hz) 1280MB NVIDIA GeForce GTX 570 (Gigabyte) 58 °C Hard Drives 212GB Volume0 (RAID) 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 36 °C 1863GB Western Digital WDC WD20EARS-00MVWB0 (SATA) 34 °C Optical Drives No optical disk drives detected Audio ASUS Xonar Essence STX Audio Device Operating System Windows 8 Pro 64-bit Computer type: Desktop Graphics Monitor 1 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Secondary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY4\Monitor0 Monitor 2 Name DELL U2713HM on NVIDIA GeForce GTX 570 Current Resolution 2560x1440 pixels Work Resolution 2560x1400 pixels State Enabled, Output devices support Multiple displays Extended, Primary, Enabled Monitor Width 2560 Monitor Height 1440 Monitor BPP 32 bits per pixel Monitor Frequency 59 Hz Device \\.\DISPLAY5\Monitor0 NVIDIA GeForce GTX 570 Manufacturer NVIDIA Model GeForce GTX 570 GPU GF110 Device ID 10DE-1086 Revision A2 Subvendor Gigabyte (1458) Series GeForce GTX 500 Current Performance Level Level 3 Current GPU Clock 845 MHz Current Memory Clock 1900 MHz Current Shader Clock 1690 MHz Voltage 0.988 V Technology 40 nm Die Size 520 mm² Release Date Dec 07, 2010 DirectX Support 11.0 OpenGL Support 5.0 Bus Interface PCI Express x16 Temperature 57 °C Driver version 9.18.13.2018 BIOS Version 70.10.55.00.01 ROPs 40 Shaders 512 unified Memory Type GDDR5 Memory 1280 MB Bus Width 64x5 (320 bit) Filtering Modes 16x Anisotropic Noise Level Moderate Max Power Draw 219 Watts Count of performance levels : 3 Level 1 - "Default" GPU Clock 50 MHz Memory Clock 135 MHz Shader Clock 101 MHz Level 2 - "2D Desktop" GPU Clock 405 MHz Memory Clock 324 MHz Shader Clock 810 MHz Level 3 - "3D Applications" GPU Clock 845 MHz Memory Clock 1900 MHz Shader Clock 1690 MHz Things I've tried: 1) Updating the graphics driver 2) Setting windows power mode to High Performance 3) Reset Nvidia Global Performance settings to default

    Read the article

  • ubuntu hardrive repartition without uninstalling ubuntu or windows 7 and losing data of hardrive

    - by user141692
    I have and asus r500v with 750 gb gpt system uefi motherboard core i7 3610qm, nvidia geforce gt, with ubuntu and w7 dual boot, I had problems installing ubuntu because of the grub but I fix it with https://bugs.launchpad.net/ubuntu/+source/grub2/+bug/807801, but I still have the problem of "warning: the partition is misaligned by 3072 bytes. this may result iin very poor performance. Repartitioning is suggested" in every linux partitioin I made and my 750 gb is not being used at the maximun capacity it only uses 698 gb. I want to make partitions so that the warning doesnt show up and I can use the maximum capacity of the HDD, as I did with another dual boot laptop (compaq presario cq40). I have the following partitions: unknown 1.0Mb: partition type: lynux Basic DAta partition, device: /dev/sda2 Usage: --, Partition flags: --, partition label:-- warning: the partition is misaligned by 3072 bytes. this may result in very poor performance. repartitioning is suggested. -system 210 Mb FAt, usage: Filesystem, partition type: EFI system Partition, Partition Flags:--, Label: system, Device: /dev/sda1, partition label: EFI system partition, Capacity 210MB, avilable:--, Mount Point: mounted at /boot/efi -134 Mb NTFS, usage: filesystem, partition type: linux basic data partition, partition flags:.--, device: /dev/sda7, partition label: --, capacity: 134MB,available:--, mount point: not mounted -OS 250 GB NTFS, usage: file system, partititon type: linux basic data partition, partition flags: --, type: NTFS, label: OS, device: /dev/sda3, partition label: basic data partition, capacity: 250 GB, available:-, mount point: not mounted -10GB FAT 32, usage: filesystem, partition type: EFI system partition, partition flags:--, type: FAT 32, label: --, device: /dev/sda4, partition label: --, capacity: 10GB, available:--, mount point: not mounted warning: the partition is misaligned by 3072 bytes. this may result in very poor performance. repartitioning is suggested. -10gb ext 4, usage: file system, partition type: linux basic data partition, partition flags:--, type: EXT4(version1) label:--, device: /dev/sda9, partition label:--, capacity: 10 GB, available:--, mount point at / warning: the partition is misaligned by 1536 bytes. this may result in very poor performance. repartitioning is suggested. -478GB ext4, usage: filesystem, partition type: linux basic data partition, partition flags:--, type: EXT4, label:--, device: /dev/sda5, partition label:--, capacity: 478gb, available:--, mount point: mounted at /home warning: the partition is misaligned by 512 bytes. this may result in very poor performance. repartitioning is suggested. -2.0gb Swap 2.0Gb, usage: swap space, partition type: linux swap partitioin, partition flags:-, device: /dev/sda6, partition label: capacity: 2.0gb warning: the partition is misaligned by 512 bytes. this may result in very poor performance. repartitioning is suggested. and as you can see it is not well organized so please help me to organize the partitions witahout uninstalling the w7, and if possible the grub2

    Read the article

  • How to diagnose repeated "Starting up database '<dbname>'"

    - by Richard Slater
    I have a SQL 2008 server which is predominantly used as a development server, in the last two weeks it has been having occasional "fits", I have isolated the cause of these fits as CHECKDB being run almost continuiously, the following log information is logged to the Windows Event Log (Source: MSSQLSERVER, Category: Server): Event: 1073758961, Message: Starting up database 'DBName1'. Event: 1073758961, Message: Starting up database 'DBName2'. Event: 1073759397, Message: CHECKDB for database 'DBName1' finished without errors on 2010-07-19 20:29:26.993 (local time). This is an informational message only; no user action is required. Event: 1073759397, Message: CHECKDB for database 'DBName1' finished without errors on 2010-07-19 20:29:26.993 (local time). This is an informational message only; no user action is required. This is repeated every 1-2 seconds untill SQL Server is restarted or the offending databases are detatched. I initially thought that it was a problem with the databases so I took a backup and restored them to a SQL Express instance, all of the data is in tact, and CHECKDB runs without problem. The two databases that were causing a problem last week were not being used; so I took full backups of them and detached the databases, this resolved the problem. However at 0100 GMT this morning to other totally unrelated databases started showing the same problems. There is nothing in the event log to suggest that something happened to the server such as a restart, there are no messages about processes crashing or issues being detected with the storage controller. Speaking to the owner of the company this computer has suffered from "gremlins" in the past, however advice was taken and the motherboard was replaced and the computer rebuilt, memory and processor are the same. Stats: O/S: Windows 2008 Standard Build 6002 CPU: 2x Pentium Dual-Core E5200 @ 2.5GHz RAM: 2GB SQL: 2008 Standard 10.0.2531 Edit: someone posted then deleted a comment about AutoClose, it was turned on on the databases affected. It seems that best practice is to disable it so I have done that with the folllowing. EXECUTE sp_MSforeachdb 'IF (''?'' NOT IN (''master'', ''tempdb'', ''msdb'', ''model'')) EXECUTE (''ALTER DATABASE [?] SET AUTO_CLOSE OFF WITH NO_WAIT'')' I won't know if the problem recurs for some time so I am still open to further answers.

    Read the article

  • Why do I see a large performance hit with DRBD?

    - by BHS
    I see a much larger performance hit with DRBD than their user manual says I should get. I'm using DRBD 8.3.7 (Fedora 13 RPMs). I've setup a DRBD test and measured throughput of disk and network without DRBD: dd if=/dev/zero of=/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 4.62985 s, 116 MB/s / is a logical volume on the disk I'm testing with, mounted without DRBD iperf: [ 4] 0.0-10.0 sec 1.10 GBytes 941 Mbits/sec According to Throughput overhead expectations, the bottleneck would be whichever is slower, the network or the disk and DRBD should have an overhead of 3%. In my case network and I/O seem to be pretty evenly matched. It sounds like I should be able to get around 100 MB/s. So, with the raw drbd device, I get dd if=/dev/zero of=/dev/drbd2 bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 6.61362 s, 81.2 MB/s which is slower than I would expect. Then, once I format the device with ext4, I get dd if=/dev/zero of=/mnt/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 9.60918 s, 55.9 MB/s This doesn't seem right. There must be some other factor playing into this that I'm not aware of. global_common.conf global { usage-count yes; } common { protocol C; } syncer { al-extents 1801; rate 33M; } data_mirror.res resource data_mirror { device /dev/drbd1; disk /dev/sdb1; meta-disk internal; on cluster1 { address 192.168.33.10:7789; } on cluster2 { address 192.168.33.12:7789; } } For the hardware I have two identical machines: 6 GB RAM Quad core AMD Phenom 3.2Ghz Motherboard SATA controller 7200 RPM 64MB cache 1TB WD drive The network is 1Gb connected via a switch. I know that a direct connection is recommended, but could it make this much of a difference? Edited I just tried monitoring the bandwidth used to try to see what's happening. I used ibmonitor and measured average bandwidth while I ran the dd test 10 times. I got: avg ~450Mbits writing to ext4 avg ~800Mbits writing to raw device It looks like with ext4, drbd is using about half the bandwidth it uses with the raw device so there's a bottleneck that is not the network.

    Read the article

  • OCZ Vertex 2 not recognized by Ubuntu installer

    - by Zsub
    As I boot into the Ubuntu 10.10 (or 11.04, doesn't matter) live environment or installer, it just refuses to recognise my Vertex 2. It reports the disk as ATA and not supporting smart, shows no serial number, and doesn't list the size correctly. All fdisk tells me is Unable to read /dev/sda (it's the only storage in the PC). I'm now running a temporary install of Windows 7 off of it, which worked like a charm, so where am I going wrong with Ubuntu... Specs: Asus M4N68T-M LE V2 (BIOS 0702, most recent) OCZ Vertex 2 SSD 60 GB Amd Athlon II X4 640 Patriot PSD34G13332 4GB DDR3 ram (two banks) EDIT I installed a second drive, installed Ubuntu on that and booted, it recognised the SSD just fine. I'm now trying to apt-get upgrade the live-environment. I wonder if there is any way to sort of install Ubuntu from Ubuntu (I boot into the working install on the other drive, install it on the SSD and then boot from the SSD). EDIT2 Ok, so that doesn't work. The install detects the SSD, however, it cannot format it. EDIT3 After a fresh boot I can read out SMART-data and even perform a read-benchmark, but if I try to format it, or do a write-bench, it'll crap out and after that it says SMART is not supported. So basically it seems I can't write to the disk, as it will stop working when I do, I will try to run repeated read-benchmarks to see if that has any effect. EDIT4 I'm running several read benchmarks on the drive right now, they give results that are to be expected from an SSD. If the read-benches don't fail, I can use fdisk on the disk, but it is now stuck trying to re-read the partition table after issueing the 'w' command. EDIT5 Parted Magic did recognize the drive and with hdparm -I even could tell me the drive was in a frozen state. I powercycled it (just pull out the plug from the SSD and plug it back in) and it wasn't frozen anymore. After that I could upgrade the firmware on the drive (still using Parted Magic) and format it to Ext4. After I rebooted into the Ubuntu installer, it wouldn't get recognized and hdparm didn't want to talk to it saying HDIO_DRIVE_CMD(identify) failed: Invalid exchange. EDIT6 For some reason if I enable one of the RAID controllers (the one the SSD is connected to, obviously) Ubuntu will let me format it, mount it and write to it. The installer also recognizes it. However if the raid controller is enabled but no array is defined the motherboard can't boot from it :(

    Read the article

  • Bladecenter-E Power Module fault

    - by Lihnjo
    We have problem on IBM Bladecenter-E Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy What is the best solution for this problem? Thanks AMM Service Data Help SPAPP Capture Available 10/13/2010 17:03:47 1090347 bytes Time: 11/19/2012 11:02:31 UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 MAC Address xx:xx:xx:xx:xx:xx MM Information Name: nnnnn Contact: aaa, bbb, ccc, England Location: [email protected] IP address: 111.222.333.444 Date Time Information GMT offset: +1:00 - Central Europe Time (Western Europe, Algeria, Nigeria, Angola) Adjust for DST: Yes NTP: Enabled NTP Hostname/IP: 111.222.333.444 System Health: Critical System Status Summary One or more monitored parameters are abnormal. Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy CHASSIS (BladeCenter-E) in CHASSIS slot: 01 TopoPath is "CHASSIS[1]". Description : BladeCenter-E Width : 1 Sub Type : BladeCenter (BC) Power Mode : 220 v KVM Owner : CHASSIS[1]/BLADE[9] MT Owner : CHASSIS[1]/MGMT_MOD[1] Component Type : CHASSIS Inventory: VPD ID: 336 (decimal) POS ID EXT: 0 (decimal) POS ID: 8 (decimal) Machine Type/Model: 86773RG Machine Serial Number: 99ZL816 Part Number: 39R8561 FRU Number: 39R8563 FRU Serial Number: YK109174W1HV Manufacturer ID: IBM Hardware Revision: 3 (decimal) Manufacture Date: 18 (wk), 07 (yr) UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 (hex) Type Code: 97 (decimal) Sub-type Code: 0 (decimal) IANA Num: 336 (decimal) Product ID: 8 (decimal) Manufacturer Sub ID: FOXC Enviroment data: -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0xa Sensor Label: : Midplane Sensor ID: : 0x0 MGMT MOD (Advanced Management Module) in MGMT_MOD slot: 01 TopoPath is "CHASSIS[1]/MGMT_MOD[1]". Description : Advanced Management Module Name : kant Width : 1 Component Role : Primary Component Type : MGMT MOD Insert Time : 28050132 Inventory: VPD ID: 288 (decimal) POS ID EXT: 0 (decimal) POS ID: 4 (decimal) Part Number: 39Y9659 FRU Number: 39Y9661 FRU Serial Number: YK11836CE2RC Manufacturer ID: IBM Hardware Revision: 4 (decimal) Manufacture Date: 50 (wk), 06 (yr) UUID: 1D95 9937 8CA5 11DB 9499 0014 5EDF 1C98 (hex) Type Code: 81 (decimal) Sub-type Code: 1 (decimal) IANA Num: 20301 (decimal) Product ID: 65 (decimal) Manufacturer Sub ID: ASUS Firmware data: Type : AMM firmware Build ID : BPET50P File Name : CNETCMUS.PKT Release Date : 03/26/2010 Release Level : 50 Revision - Major: 80 Port info: ======================================================== Topology Path ID : 1 Label : External Phy Orientation : EXTERNAL Port Number : 1 Type : MGT Physical Meidum : Copper Number of Link Intferfaces : 1 ------------------------------------ Link Ifc ID Number : 1 Link Ifc Transport Protocol : ENET Link Ifc Addr Type : MAC Link Ifc Burned-in Addr : xx:xx:xx:xx:xx:xx Link Ifc Admin Addr : 00:00:00:00:00:00 Link Ifc Addr in use : xx:xx:xx:xx:xx:xx ---------------------------------------------------------- Configuration behaviors: Save Only Enviroment data: -------------- Type: : TEMPERATURE Unit: : DEGREES_C Reading: : 38.00 Sensor Label: : MM Ambient Sensor ID: : 0x0 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +4.81 Sensor Label: : +5V Sensor ID: : 0x1b -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +3.26 Sensor Label: : +3.3V Sensor ID: : 0x19 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +11.97 Sensor Label: : +12V Sensor ID: : 0x16 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : -4.88 Sensor Label: : -5V Sensor ID: : 0x1e -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +2.47 Sensor Label: : +2.5V Sensor ID: : 0x18 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +1.76 Sensor Label: : +1.8V Sensor ID: : 0x15 -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0x19 Sensor Label: : kant Sensor ID: : 0x0

    Read the article

  • Share 3G connection over WiFi-LAN network

    - by kush.impetus
    This is how I have established network between my PC and my laptop at home (being novice in networking, it took me few days to achieve the feat). And it is working perfectly. I can easily share files between them. Laptop IP Address: 192.168.1.4 Subnet mask: 255.255.255.0 Default Gateway: 192.168.1.2 Desktop IP Address: 192.168.1.5 Subnet mask: 255.255.255.0 Default Gateway: 192.168.1.2 ASUS RT-N10+ Router IP Address: 192.168.1.4 Default Gateway: 192.168.1.2 I have connected the Desktop PC to the router using a LAN cable, and laptop to router over WiFi. Both, PC and laptop are running on Windows 7 OS, are on same HomeGroup, have same username / password. Also, I have connected the Ethernet cable to LAN port 1 of the router. Click here to view a graphical representation of the network. Can't post image here, because I don't have 10 reputation points. Now, what I want is use connect to Internet using a 3G USB modem on one device and share it over the network on the other. I tried Huawei and Micromax 3G USB modem. Both obtain a new IP address whenever I connect to Internet (means they have dynamic IPs). Rest, both have Subnet Mask as 255.255.255.255 and Default Gateway as 0.0.0.0. In that case, I cannot directly share Internet from the modem. Preferred DNS is blank for now in both, laptop and PC. What I am planning to do is to connect to Internet on laptop using the 3G modem and share the Internet connection over laptop's Wi-Fi (as hotspot) using Connectify, which I have done already. That, I suppose, will broadcast a static IP to connect to. Now what I can't figure out is that what changes should I make to the network settings of the router and the PC so that PC connects to the Internet broadcast by Connectify? Is that possible on the first hand? Please note that I am trying to implement the network without spending anything extra (for purchasing as USB WiFi adapter for PC, of course, which could have made the life lot easier for me). Thanks in advance

    Read the article

  • Best Processor for MediaSmart Server?

    - by Kent Boogaart
    I'm trying to figure out what the best possible processor is that I can stick in my HP MediaSmart server. I'm clueless when it comes to correlating CPUs to motherboards. I suspect it's the socket type I care about, but I worry that there's more to it. CPU-Z gives me (excerpt): Processors Information ------------------------------------------------------------------------- Processor 1 ID = 0 Number of cores 1 (max 1) Number of threads 1 (max 1) Name AMD Sempron LE-1150 Codename Sparta Specification AMD Sempron(tm) Processor LE-1150 Package Socket AM2 (940) CPUID F.F.1 Extended CPUID F.7F Brand ID 1 Core Stepping DH-G1 Technology 65 nm Core Speed 1000.0 MHz Multiplier x FSB 5.0 x 200.0 MHz HT Link speed 800.0 MHz Stock frequency 2000 MHz Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, x86-64 L1 Data cache 64 KBytes, 2-way set associative, 64-byte line size L1 Instruction cache 64 KBytes, 2-way set associative, 64-byte line size L2 cache 256 KBytes, 16-way set associative, 64-byte line size FID/VID Control yes Max FID 10.0x Max VID 1.350 V P-State FID 0x2 - VID 0x12 (5.0x - 1.100 V) P-State FID 0xA - VID 0x0C (9.0x - 1.250 V) P-State FID 0xC - VID 0x0A (10.0x - 1.300 V) K8 Thermal sensor yes K8 Revision ID 6.0 Attached device PCI device at bus 0, device 24, function 0 Attached device PCI device at bus 0, device 24, function 1 Attached device PCI device at bus 0, device 24, function 2 Attached device PCI device at bus 0, device 24, function 3 Chipset ------------------------------------------------------------------------- Northbridge SiS 761GX rev. 02 Southbridge SiS 966 rev. 59 Graphic Interface AGP AGP Revision 3.0 AGP Transfer Rate 8x AGP SBA supported, enabled Memory Type DDR2 Memory Size 2048 MBytes Channels Single Memory Frequency 200.0 MHz (CPU/5) CAS# latency (CL) 5.0 RAS# to CAS# delay (tRCD) 5 RAS# Precharge (tRP) 5 Cycle Time (tRAS) 15 Bank Cycle Time (tRC) 21 Command Rate (CR) 1T DMI ------------------------------------------------------------------------- DMI BIOS vendor Phoenix Technologies, LTD version R03 date 05/08/2008 DMI System Information manufacturer HP product MediaSmart Server version unknown serial CN68330DGH UUID A482007B-B0CC7593-DD11736A-407B7067 DMI Baseboard vendor Wistron model SJD4 revision A.0 serial unknown DMI System Enclosure manufacturer HP chassis type Desktop chassis serial unknown DMI Processor manufacturer AMD model AMD Sempron(tm) Processor LE-1150 clock speed 2000.0 MHz FSB speed 200.0 MHz multiplier 10.0x DMI Memory Controller correction 64-bit ECC Max module size 4096 MBytes DMI Memory Module designation A0 size 2048 MBytes (double bank) DMI Memory Module designation A1 DMI Memory Module designation A2 DMI Memory Module designation A3 DMI Port Connector designation PS/2 Mouse (internal) port type Mouse Port connector PS/2 connector PS/2 DMI Port Connector designation USB0 (external) port type USB DMI Physical Memory Array location Motherboard usage System Memory correction None max capacity 16384 MBytes max# of devices 4 DMI Memory Device designation A0 format DIMM type unknown total width 64 bits data width 64 bits size 2048 MBytes DMI Memory Device designation A1 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A2 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A3 format DIMM type unknown total width 64 bits data width 64 bits How do I figure out what options I have for an upgrade?

    Read the article

  • DVD Drive Failing on Windows 7

    - by Seth Spearman
    Hello, I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

    Read the article

  • Some apps very slow to load on Windows 7, copy & paste very slow.

    - by Mike
    Hello, I searched here and couldn't find a similar issue to mine but apologies if I missed it. I've searched the web and no one else seems to be having the same issue either. I'm running Windows 7 Ultimate 64bit on a pretty high spec. machine (well, apart from the graphics): Asus M4A79T Deluxe AMD Phenom II 965 black edition (quad core, 3.4GHz) 8GB Crucial Ballistix DDR 1333MHz RAM 80GB Intex X25 SSD for OS 500GB mechanical drive for data. ATi Radeon HD 4600 series PCI-e Be Quiet! 850W PSU I think those are all the relevant stats, if you need anything else let me know. I've updated chipset, graphics and various other drivers all to no avail, the problem remains. I have also unplugged and replugged every connection internally and cleaned the RAM edge connectors. The problems: Video LAN (VLC) and CDBurnerXP both take ages to load, I'm talking 30 seconds and 1 minute respectively which is really not right. Copy and paste from Open Office spread sheet into Fire Fox, for example, is really, really slow, I'll have pressed control V 5 or 6 times before it actually happens, if I copy and then wait 5 to 10 seconds or so it'll paste first time so it's definitely some sort of time lag. Command and Conquer - Generals: Zero Hour. When playing it'll run perfectly for about 10 or 20 seconds then it'll just pause for 3 or 4 then run for another 10 or 20 seconds and pause again and so on. I had the Task Manager open on my 2nd monitor whilst playing once and I noticed it was using about 25% of the CPU, pretty stable but when the pause came another task didn't shoot up to 100% like others on the web have been reporting (similar but not the same as my issue, often svchost.exe for them) but dropped to 2 or 3% usage then back up to 25% when it started playing properly again. Very odd! But it gets even odder... I had a BSOD and reboot last week, when it rebooted the problem had completely gone, I could play C&C to my heart's content and both the other apps loaded instantly, copy and paste worked instantly too. I did an AVG update earlier this week which required a reboot, rebooted and the problem's back. I don't think it's AVG related though, I think it was just coincidence that's the app that required a reboot. I think any reboot would have brought the issue back. A number of reboots later and it hasn't gone away again. If any one could make any suggestions as to the likely cause and solution to these issues I'd be most grateful, it's driving me nuts! Thanks, Mike....

    Read the article

  • DVD Drive Failing on Windows 7

    - by Seth Spearman
    I have x64 Windows 7 running on an ASUS M50VM. The DVD drive works completely unreliably if not at all. But the story is not that simple so bear with me...here are the gory details. When I first got the machine it came with Windows XP and I upgraded it to Windows Vista X64 and the DVD worked fine. When Windows 7 RC2 came out I tried it on a Virtual Machine and I liked it so much that I upgraded the machine to Win7 RC1. The DVD worked fine. Of course, RC1 was going to start spontaneously rebooting, so when Windows 7 was released I DID A CLEAN INSTALL of Windows 7. Just to clarify...by clean install I mean I did a FORMAT of the HARD DRIVE and INSTALLED it from scratch. EVER since then the DVD mostly doesn't work. I can sometime read from disk but that will often hang. (Please see my description below of HANG for details.) CD or DVD writes ALWAYS fail with a HANG (I have done a successful write only one time.) Here is what I mean by HANG... *Explorer Window is unresponsive. *Any software accessing the DVD drive is unresponsive. *The DVD tray will not eject. *Using a paper clip will eject but the disk is usually spinning real hard. *Attempting to shut down windows will fail. I have waited as long as ten minutes but the whole OS seems to hang. I do a hard shutdown. *Sometimes accessing the DVD (when it does not cause a HANG) will still fail and the device will actually seem to disappear from the system until I reboot. A couple of other things. It is NOT a hardware failure. It is the Windows OS. I know this because I swapped out my DVD drive with a friend with the same model...his machine is fine (he is still running Vista X64) and my machine still fails. For what it is worth. I swapped out my primary disk with the INTEL 160GB SSD. EDIT Here is what System Information shows about my DVD drive Drive D: Description CD-ROM Drive Media Loaded No Media Type DVD Writer Name HL-DT-ST DVDRAM GSA-T50N ATA Device Manufacturer (Standard CD-ROM drives) Status OK Transfer Rate -1.00 kbytes/sec SCSI Target ID 0 PNP Device ID IDE\CDROMHL-DT-ST_DVDRAM_GSA-T50N________________RR04____\5&2B5B7F1D&0&1.0.0 Driver c:\windows\system32\drivers\cdrom.sys (6.1.7600.16385, 144.00 KB (147,456 bytes), 7/13/2009 7:19 PM) Any ideas? HELP! Seth B Spearman

    Read the article

  • Easiest way to replace preinstalled Windows 8 with new hard drive with Windows 7

    - by Andrew
    There are all kinds of questions and answers relevant moving Windows 8 to a new hard drive. I'm not seeing anything quite applicable to my situation. I have a new, unopened, unbooted notebook with pre-installed Windows 8. I will be replacing the hard drive before ever booting, unless that is not possible for some reason. I want to "downgrade" to Windows 7 Pro, and I want a clean installation. To do so legitimately, I apparently either need to: Upgrade Windows 8 to Windows 8 Pro using Windows 8 Pro Pack, then downgrade; or Just install a newly-licensed copy of Windows 7 Pro. (Let me know if I've missed an option.) Installation media is likely not a problem, though if I need something vendor-specific that I cannot otherwise download, that could present an issue (Asus notebook, if that matters). If I could, I would just buy the Pro Pack upgrade, swap the hard drive (without ever booting), then install Windows 7 Pro directly on the new hard drive, using the Pro Pack key for activation. Will this work? Are there any activation issues? Edited to clarify, as some comments and answers indicate confusion: Here is, ideally, what I want to do: Before ever powering on the notebook, remove the current hard drive. Replace this hard drive with a new, blank hard drive. Install a clean copy of Windows 7 Pro on this new, blank hard drive. Unless I have no choice to accomplish the end result (a clean install of Win7 Pro on the newly-installed, previously-blank hard drive), I am not wanting to: Install Windows 7 "over" the current Windows 8 install (after upgrading to Win8 Pro). That would involve using the currenly-installed hard drive. I want to use a new, different hard drive. Copy the Win8 install to the new hard drive, then install Windows 7 "over" that installation. Install Windows 7 "over" the current Windows 8 install (after upgrading to Win8 Pro), then copy the installation to the new hard drive. If I have to use one of those three options, I will, but only if there is no other choice. Please note that this question is not about licensing: I will purchase the necessary license(s) to accomplish this procedure legally (apparently either Win8 Pro Pack or Win7 Pro -- the former currently appears less expensive).

    Read the article

  • GeForce 8800GT not even giving basic output

    - by Sam
    My Dad bought a GeForce 8800GT graphics card quite a long time ago now. It has never worked in his PC. Print out from a dxdiag: System Information Time of this report: 4/13/2010, 19:52:40 Machine name: USER-PC Operating System: Windows Vista™ Home Premium (6.0, Build 6001) Service Pack 1 (6001.vistasp1_gdr.091208-0542) Language: English (Regional Setting: English) System Manufacturer: To Be Filled By O.E.M. System Model: To Be Filled By O.E.M. BIOS: Default System BIOS Processor: Intel(R) Core(TM)2 Quad CPU Q6600 @ 2.40GHz (4 CPUs), ~2.3GHz Memory: 2046MB RAM Page File: 1045MB used, 3296MB available Windows Dir: C:\Windows DirectX Version: DirectX 10 DX Setup Parameters: Not found DxDiag Version: 6.00.6001.18000 32bit Unicode DxDiag Notes Display Tab 1: No problems found. Sound Tab 1: No problems found. Sound Tab 2: No problems found. Sound Tab 3: No problems found. Input Tab: No problems found. DirectX Debug Levels Direct3D: 0/4 (retail) DirectDraw: 0/4 (retail) DirectInput: 0/5 (retail) DirectMusic: 0/5 (retail) DirectPlay: 0/9 (retail) DirectSound: 0/5 (retail) DirectShow: 0/6 (retail) Display Devices Card name: ATI Radeon HD 2400 PRO Manufacturer: ATI Technologies Inc. Chip type: ATI Radeon Graphics Processor (0x94C3) DAC type: Internal DAC(400MHz) Device Key: Enum\PCI\VEN_1002&DEV_94C3&SUBSYS_00000000&REV_00 Display Memory: 1012 MB Dedicated Memory: 245 MB Shared Memory: 767 MB Current Mode: 1280 x 960 (32 bit) (75Hz) Monitor: Generic PnP Monitor Driver Name: atiumdag.dll,atiumdva.dat,atitmmxx.dll Driver Version: 7.14.0010.0523 (English) DDI Version: 10 Driver Attributes: Final Retail Driver Date/Size: 8/22/2007 02:43:14, 3021312 bytes That info is from the current card that is installed in it and has been installed since its purchase roughly 3-4 years ago. When I physically install the card I put it into a purple slot on the motherboard that the old card was in (if I go into the device manager and select properties on the current card it confirms that the slot is a "PCI Slot 16 (PCI bus 2, device 0, function 0)") and boot up the computer but get absolutely no output. The screen that we have registers that it is connected to something (by not displaying the screen it does when the cable is unplugged) but just remains blank, no output at all. I recently took the card to my University and one of my friends who is better with hardware issues than I am tried it in his system and it worked perfectly. No issues whatsoever. I do not have a spec list for his system but I could get one if you need it. If you need any more information on this issue I will be happy to supply you with it as I am starting to get very annoyed with this problem ^_^

    Read the article

  • Win 8: Adding a boot volume to an MBR dynamic disk [NOT about changing to basic disks]

    - by Stilez
    (This is NOT aiming to convert to basic disk. In this question, the disk stays dynamic but becomes bootable) There doesn't seem to be a clear, well stated answer I can find, for the question "What are the criteria for Windows 8 to successfully boot from an MBR dynamic disk", or "how do I fix a dynamic MBR partition that's failing boot"? I've tried to educate myself but can't find crucial information to clear it all up. My existing HDD/SSD setup: DISK 0 ~ 60GB SSD/MBR/basic: (350MB recovery)(60GB windows 8 bootable) DISK 1 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB unallocated)(410GB mirrored data) DISK 2 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB unallocated)(410GB mirrored data) DISKS 3, 4, 5: (ignored for simplicity: 2xHDD RAID1 + caching SSD) I'm heavy duty on data crunching and virtualisation, just maxxed out 32GB RAM @ 2133 and moved to 4960X + 64GB. Disk 0 is a pure system disk of little value, and virtualisations runs off mirrored SSDs (Samsung 840 Pro 512 x 2) for double speed reading and so they snapshot in reasonable time. I'm using 4 SATA3 ports and the board only has two decent Intel ports (onboard Marvell are poorer quality). I'm wary of choosing between LSI, HighPoint and other 3rd party controllers as I'm unfamiliar with the maze of decent RAID cards (that's a whole other issue!). I want to cut down my SSD needs by moving the boot volume and caching volume to the 840 pros, giving a setup with 2 fewer SSDs: DISK 0 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(60GB boot)(410GB mirrored data) DISK 1 ~ 512GB SSD/MBR/dynamic: (350MB recovery)(30GB cache for the ICH10R mirror)(30GB temp)(410GB mirrored data) DISKS 2, 3: (2xHDD RAID1) Intel's RST allows this, Win 8 allows booting off a MBR/dynamic disk, and the two 60GB SSDs are hardly the fastest SSDs anyway, they'll get repurposed. Moving the caching volume is easy. Moving the boot volume has me stumped. The difficulty is, I'm hitting a wall of knowledge here. I have a UEFI Asus motherboard with an previous traditional MBR/basic boot disk, and I want it to boot from a disk and volume that's MBR/dynamic. The disk copy is physically ok (Partition Wizard Server will copy to dynamic volumes) but then hits a light blue 0xc000000e boot error. No real surprise, I expected to have some boot fixing, but had expected Windows to boot-fix it (all drivers exist), or the usual manual fixes to work. Specifically, I don't know enough, to know what's got to be manually checked and perhaps corrected for the disk to boot (legacy/uefi/bios, odd partitions, boot tables, disk IDs, hidden boot files, oh my!), or if I need to change any of this secure boot/UEFI/legacy stuff in the bios, convert a 512 SSD to basic and then back to dynamic when working, or if the issue is pure OS config using "diskpart", "bootsect" and "bootrec" from the Win8 DVD. The old system disk still boots but I don't know enough to figure what to fix, to make the system boot as I want. The answers probably aren't hard but the real issue is my confusion and missing information. Thanks for helping!

    Read the article

  • Crashes and freezes after fixing "BOOTMGR is missing" error

    - by Greg-J
    I came back from a 3-day weekend to a computer that was off. I leave my PC on 24/7, so this was odd. Turn it on to get the dreaded "BOOTMGR is missing" screen. Two attempts at Windows Recovery and it booted into Windows fine. After an hour or so, I get a frozen Chrome and my start bar disappears. Ctrl+Alt+Del brings up an error box telling me that Ctrl+Alt+Del failed to work properly. Clicking on any open application triggers an error (I can't recall the error now, but it essentially just said that the application couldn't be found running or something along those lines). I restart, and again, the same thing happens after a while of use. I turn it on, install the 47 updates I have or so, and then restart it. After a while of use (under an hour), it just freezes completely. My thoughts are: SSDs, RAM or PS. My system specs below: (RAID0) 2 x Crucial M4 CT128M4SSD2 2.5" 128GB SATA III MLC Internal Solid State Drive (SSD) CORSAIR Vengeance 16GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model CML16GX3M4A1600C9 CORSAIR HX Series HX750 750W ATX12V 2.3 / EPS12V 2.91 SLI Ready CrossFire Ready 80 PLUS GOLD Certified Modular Active 1 x ASUS Maximus IV Gene-Z/GEN3 LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard 1 x Hitachi GST Deskstar 7K1000.C 0F10383 1TB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive 1 x Intel Core i7-2600K Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 1 x SAPPHIRE 21197-00-40G Radeon HD 7970 3GB 384-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card 1 x Noctua NH-D14 120mm & 140mm SSO CPU Cooler This is all crammed in a pretty small case (NZXT Vulcan) and has been running perfectly problem-free since January. The only thing out of the ordinary is that there is a fan in the case that is now making noise whereas the case has previously been completely silent. I have no reason to believe this is anything more then correlation, but felt it is worth mentioning. I believe it MAY be the SSDs simply because of the BOOTMGR error, but not sure how to test that theory. My belief that it may be the RAM is simply from experience with frozen machines. I haven't had the time to memtest it, but will. The PS being the culprit is something I've picked up by reading similar threads on various forums, and it seems plausible. I am unsure how to test this though. ANY insight whatsover would be greatly appreciated!

    Read the article

  • CPU overheating after cleaning it

    - by Roberts
    I wanted to clean my computer CPU heatsink and fan itself, because the temperature is not what I wanted. About (50C ~ 70C). I have Intel Core 2 Duo E4300 @1.8 GHz (LGA775). The heatsink wasn't so scary filled with dust but I wanted to clean it anyway. I didn't know how to get heatsink with fan from the socket. So after 25 minutes I've figured it out. But I didn't know how to get it back on so I spent a lot time getting out the motherboard from the case. The fan and heatsink... The case and all components are clear of dust. (I'm tired now). Then I put all back just the way it was, well did few things on cable management. But the problem was that I didn't know how to connect front audio connectors. I had Windows XP hibernated. So I started the PC and everything was normal, except CMOS memory was clear. I configured the BIOS just the way it was and while I was doing that I saw about 58C CPU temperature and fan at 1789 RPM. Restarted the computer with new settings applied. But Windows halted with Blue Screen (I forgot what error it was but something with KERNEL). Restarted the PC and deleted hibernation session and everything was back normal. But couldn't record any sound from front panel microphone. The problem was that I messed ground wire with mic. Again after fixing it I turned computer on. No problems. The fan currently is noisy and temperature was 78C. The temperature before was 55C - 60C at idle. Now it's about 60C. If I do something then temperature raises to 79C. While speaking in skype the temperature was 82C. Could this problem occur because of the thermal grease (it's old and never replaced)? Edit The problem wasn't in thermal paste (because I didn't touch it). The problem was that I installed heatsink wrong. Now instead of regular 60C CPU temperature the CPU is at 48C (cool).

    Read the article

  • Setting up a WPA-PSK network card to connect to a WPA2 network

    - by mattshepherd
    I'm currently doing a spare-parts build to put a media computer in the living room, and having a devil of a time getting my Rosewill RNX-6300 wireless card to connect to my network. I'm trying to set it up using Windows as opposed to the proprietary Rosewill software -- the Rosewill software is a little over my head. It can find the network fine, but when I try to connect, I don't get the password prompt -- it moves straight to "validating identity," scans, and then says "Windows was not able to find a certificate to log you on to the wireless network Foo." The maddening thing is that the card was working fine a week ago, in the same box, using the same OS. I pulled everything out, swapped out the motherboard, and reinstalled Windows on a freshly wiped hard drive, and now I can't get it up and running again. Suggestions? I've taken several runs at it, including attempting to manually change the settings for the network to include WPA-PSK and AES and the password, and I'm a bit worried that I've totally boned everything. My router settings: ipconfig/all results from the XP box: Again, this card was working on this network a week ago. I can't figure out why I can't get it up and running now. There's no WPA2 on the card, just WPA and WPA-PSK: WPA-PSK was the only setting that would let me enter a network key. I had TKIP and AES as options there, but cipher type is AES on the router, so I chose that. (I tried TKIP later, when this didn't work, with the same results as described below.) So I set it to WPA-PSK / AES and entered my security key. It's mixed letters and numbers, 32 characters long. No joy. Still "waiting for reply" in the main screen, and "cannot find certificate" on the pop-up. And if I try again and return to the settings again, it is reset to Open/AES. It also re-enables 802.1x in the Authentication tab if I've deselected it with WPA-PSK. It also reshortens the password. I have no idea how I blundered into getting this working in the past. I am, as you can tell, far from proficient at this. It was working before, though. What am I getting wrong?

    Read the article

  • recommendations for efficient offsite remote backup solution of vm's

    - by senorsmile
    I am looking for recommendations for backing up my current 6 vm's(and soon to grow to up to 20). Currently I am running a two node proxmox cluster(which is a debian base using kvm for virtualization with a custom web front end to administer). I have two nearly identical boxes with amd phenom II x4's and asus motherboards. Each has 4 500 GB sata2 hdd's, 1 for the os and other data for the proxmox install, and 3 using mdadm+drbd+lvm to share the 1.5 TB's of storage between the two machines. I mount lvm images to kvm for all of the virtual machines. I currently have the ability to do live transfer from one machine to the other, typically within seconds(it takes about 2 minutes on the largest vm running win2008 with m$ sql server). I am using proxmox's built-in vzdump utility to take snapshots of the vm's and store those on an external harddrive on the network. I then have jungledisk service (using rackspace) to sync the vzdump folder for remote offsite backup. This is all fine and dandy, but it's not very scalable. For one, the backups themselves can take up to a few hours every night. With jungledisk's block level incremental transfers, the sync only transfers a small portion of the data offsite, but that still takes at least a half an hour. The much better solution would of course be something that allows me to instantly take the difference of two time points (say what was written from 6am to 7am), zip it, then send that difference file to the backup server which would instantly transfer to the remote storage on rackspace. I have looked a little into zfs and it's ability to do send/receive. That coupled with a pipe of the data in bzip or something would seem perfect. However, it seems that implementing a nexenta server with zfs would essentially require at least one or two more dedicated storage servers to serve iSCSI block volumes (via zvol's???) to the proxmox servers. I would prefer to keep the setup as minimal as possible (i.e. NOT having separate storage servers) if at all possible. I have also briefly read about zumastor. It looks like it could also do what I want, but it appears to have halted development in 2008. So, zfs, zumastor or other?

    Read the article

  • Why is my new Phenom II 965 BE not significantly faster than my old Athlon 64 X2 4600+?

    - by Software Monkey
    I recently rebuilt my 5 year old computer. I upgraded all core components, in particular from an Athlon 64 X2 4600+ at 2.4 GHz with DDR2 800 to a Phenom II 965 BE (quad core) at 3.6 GHz with DDR3 1333 (actually 1600, but testing consistently detected memory errors at 1600). The motherboard is also much newer and better. The HDD's (x3), DVD writer and card reader are the same. The BIOS memory config is auto-everything except the base timing which I overrode to 1T instead of 2T. The BIOS CPU multiplier is slightly over-clocked to 3.6 GHz from the stock 3.4 GHz. I noticed compiling Java is slower than I expected. As it happens I have some (single-threaded) Java pattern-matching code which is CPU and memory bound and for which I have performance numbers recorded on a number of hardware platforms, including my old system. So I did a test run on the new equipment and was stunned to find that the numbers are only slightly better than my old system, about 25%. The data set it is operating on is a 148,975 character array, which should easily fit in caches, but in any event the new CPU has larger caches all around. The system was, of course, otherwise idle for the test and the test run is a timed 10 seconds to eliminate scheduling anomalies. A long while ago, when I upgraded only memory from DD2 667 to DDR2 800 there was no change in performance of this test, which subjectively supports that the test cycle does not need to (significantly) access main memory, but yes it is creating and garbage collecting a large number of objects in the process of this test (low millions of matches are found for the pattern set). I am about 99.999% certain the code hasn't changed since I last ran it on 2009-03-17 - but I can't easily retest the old hardware, because it is currently in pieces on my work-bench waiting to be built into a new computer for my kids. Note that Windows (XP) reports a CPU speed of 795 MHz unless I have some thing running. With stuff running it seems to jump all over the place each time I use ALT-Pause to display the system properties, everywhere from 795 MHz to 3.4 Ghz. So why might my shiny new hardware under-performing so badly? EDIT: The old memory was Mushkin DDR2 800 with timings set for auto which should have been 5-5-5-12. The new memory is Corsair DDR3 1600, running at 1333 with timings also auto which are 9-9-9-21. In both cases they are a paired set of dual channel DIMMs. I was waiting to ensure my system was stable before tweaking with memory timings.

    Read the article

  • Wake On Lan only works on first boot, not sequent ones

    - by sp3ctum
    I have converted my old Dell Latitude D410 laptop to a server for tinkering. It is running an updated Debian Squeeze (6) with a Xen enabled kernel (I want to toy with virtual machines later on). I am running it 'headless' via an ethernet connection. I am struggling to enable Wake On Lan for the box. I have enabled the setting in the BIOS, and it works nicely, but only for the first time after the power cord is plugged in. Here is my test: Plug in power cord, don't boot yet Send magic Wake On Lan packet from test machine (Ubuntu) using the wakeonlan program Server expected to start (does every time) Once server has booted, log in via ssh and shut it down via the operating system After shutdown, wake server up via WOL again (fails every time) Some observations: Right after step 1 I can see the integrated NIC has a light on. I deduce this means the NIC gets adequate power and that the ethernet cable is connected to my switch. This light is not on after step 4 (the shutdown stage). The light becomes back on after I disconnect and reconnect the power cord, after which WOL works as well. After step 4 I can verify that wake on lan is enabled via the ethtool program (repeatable each time) This blog post suggested the problem may lay in the fact the motherboard might not be giving adequate power to the NIC after shutdown, so I copied an acpitool script that supposedly should signal the system to give the needed power to the card when shut down. Obviously it did not fix my issue. I have included the relevant power settings in the paste below. I have tried different combinations of parameters of shutdown (the program) options, as well as the poweroff program. I even tried "telinit 0", which I figured would do the most direct boot via software. If I keep the laptop's power button pressed down and do a hard boot this way, the light on the ethernet port stays lit and a WOL is possible. I copied a bunch of hopefully useful information in this paste I have tried this with the laptop battery connected and without it. I get the same result. Promptly pressing the power button causes the system to shut down with the message "The system is going down for system halt NOW!", and WOL is still unsuccessful.

    Read the article

  • Scoping a home dev server

    - by AbhikRK
    Hi. I’m looking to build a multi-purpose home development server. In this post, I’m looking to outline what I want from such a system, and the ‘why’s of it, to some limited extent, and finally, some rudiments of how I’m looking to go about that. I’m mostly a developer, with just about some sysadmin familiarity. So, please excuse, correct me, and suggest on any ignorance which would come across in the following ;-) It will serve the following goals to start with:- NAS (Looking at using ZFS) Source control repo e.g Git server Database e.g MySQL server Continuous Integration e.g Hudson server Other stuff as and when they come up e.g RabbitMQ etc A development sandbox to play around with new stuff I want to achieve a high uptime for 2-5 as much as possible. They should run as independent services and with minimal maintenance. (e.g TurnKey Linux appliances) I’m thinking of running them as individual Xen DomUs. Then, maybe the NAS can be a Dom0 and 6 can be another DomU. The User for this would be mostly me. I can see 2-4 being sometimes used by 2-3 users, but that would be infrequent. I’m looking for a repeatable setup. Ideally I’d like to automate this setup through Chef or Puppet or something similar. Once everything runs, I want to be able to ssh/screen/tmux into 1-6 from my laptop or any other computer on the LAN/on-the-go. My queries are:- Is putting 1-6, all of them on a single box, a good idea? If so, what kind of hardware should I be looking at, for a low-cost, low-power setup? Although not at present, but in future I might be looking at adding audio/media servers to the mix. Would that impact the answers to 1? I have an old Pentium 3 and 810e motherboard combination. Is there any way I could put it to use? I had a look at the Sheevaplug, and was wondering if I could split off the NAS on its own using that. But ruled it out preliminarily due to its reported heating issues. Is it something i should still consider? Thanks in advance

    Read the article

  • Scoping a home dev server

    - by AbhikRK
    Hi. I’m looking to build a multi-purpose home development server. In this post, I’m looking to outline what I want from such a system, and the ‘why’s of it, to some limited extent, and finally, some rudiments of how I’m looking to go about that. I’m mostly a developer, with just about some sysadmin familiarity. So, please excuse, correct me, and suggest on any ignorance which would come across in the following ;-) It will serve the following goals to start with:- NAS (Looking at using ZFS) Source control repo e.g Git server Database e.g MySQL server Continuous Integration e.g Hudson server Other stuff as and when they come up e.g RabbitMQ etc A development sandbox to play around with new stuff I want to achieve a high uptime for 2-5 as much as possible. They should run as independent services and with minimal maintenance. (e.g TurnKey Linux appliances) I’m thinking of running them as individual Xen DomUs. Then, maybe the NAS can be a Dom0 and 6 can be another DomU. The User for this would be mostly me. I can see 2-4 being sometimes used by 2-3 users, but that would be infrequent. I’m looking for a repeatable setup. Ideally I’d like to automate this setup through Chef or Puppet or something similar. Once everything runs, I want to be able to ssh/screen/tmux into 1-6 from my laptop or any other computer on the LAN/on-the-go. My queries are:- Is putting 1-6, all of them on a single box, a good idea? If so, what kind of hardware should I be looking at, for a low-cost, low-power setup? Although not at present, but in future I might be looking at adding audio/media servers to the mix. Would that impact the answers to 1? I have an old Pentium 3 and 810e motherboard combination. Is there any way I could put it to use? I had a look at the Sheevaplug, and was wondering if I could split off the NAS on its own using that. But ruled it out preliminarily due to its reported heating issues. Is it something i should still consider? Thanks in advance Have posted this question previously on SuperUser but no responses yet. So was wondering if this is a more apt forum for this.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 89 90 91 92 93 94 95 96 97  | Next Page >