Search Results

Search found 9952 results on 399 pages for 'big al'.

Page 93/399 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

• Can a USB/IDE/SATA adapter be flaky?

  - by Ward

  I use USB/IDE/SATA converters a lot and on the two that I have now, I sometimes get errors copying files to drives. It only happens when I'm copying big files to the drive (big can mean as little as 100MB, I think it happens more often with bigger files - 300MB or more), and basically the copy will fail and I'll get one or more error messages about "Delayed write failed." But if I disconnect the drive and re-connect it, I'll usually be able to continue. (The file that was being copied will be corrupt, but otherwise the drive is fine.) I just noticed a new type of flakiness: the data transfer rate can vary widely. I copied one set of files (5x300MB files) and it took 10+minutes, then I copied another set (approx. the same sizes) and it took less than a minute. I haven't done systematic testing, the other things I'm doing on my laptop at the same time might have some impact, and I haven't cross-checked the two adapters I have and the 3 hard drives I'm working with to see if there's a pattern. I'm more wondering if anyone else has seen anything like this.

  Read the article

• Why is my rsync so slow compared to pure cp or even scp?

  - by nfm

  I'm transfering the files from Linux to Windows 7 via a mounted share (the share is mounted from Windows on Linux).. I'm copying lots of data (i.e. nearly a TB) from the old to the new machine within my LAN. I'm unfortunate enough already that I only have 100MBit. Naturally I blindly used rsync but already wondered after a day why it feels so slow. Enabling the progress meter showed my a transfer rate of about 2MBit/s . So I took a reasonable big file (800MB) and tracked the transfer timing: cp : 05:33 scp (*): 06:33 rsync : 21:51 *) scp via localhost to the same Linux machine directly onto the share; completely useless but provided a progress meter The tests were as simple as (cp|scp|rsync) <source> <destination> No special arguments except host/port for scp. I even tried the -W switch for rsync but cancelled after ten minutes. rsync is 3.0.3 running on Lenny. To be able to interrupt the copy process anytime and resume lead me to rsync, but now I think I seriously need to reconsider this requirement. How's such a big difference possible?

  Read the article

• What kind of hosting do I need? [closed]

  - by Robert Smith

  I have been trying to answer this question but I haven't found an specific answer to my situation. As I want to pay for what I need, I thought I could get a good answer here. I have custom made forum (rather than a built-in forum like the ones you can find as plugins, e.g. WP-Forum or phpBB type of software) in Django. I don't want to use Apache and modwsgi because it's usually very memory-hungry and I can't afford a big server. I prefer a combination of nginx and gunicorn which I think is very efficient (maybe you can also tell me what you think about that). I'm expecting to receive 10,000 to 20,000 visits each month with 15,000 to 30,000 page impressions. I have reviewed some cloud services like Amazon EC2 or Rackspace and other more traditional services (Linodo). This site won't use videos or big images and I certainly don't need a huge amount of bandwidth (200GB would be definitely too much). I need shell access so shared hosting is out of the question. What do I need to run a website like that without problems? What about RAM? 256MB would be enough (that's the amount of RAM offered by small instances in Amazon and Rackspace)? Do you know of any alternative to those I mentioned? If you need more information to provide a useful answer, please don't hesitate to ask. Thanks a lot.

  Read the article

• Tuning up a MySQL server

  - by NinjaCat

  I inherited a mysql server, and so I've started with running the MySQLTuner.pl script. I am not a MySQL expert but I can see that there is definitely a mess here. I'm not looking to go after every single thing that needs fixing and tuning, but I do want to grab the major, low hanging fruit. Total Memory on the system is: 512MB. Yes, I know it's low, but it's what we have for the time being. Here's what the script had to say: General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries When making adjustments, make tmp_table_size/max_heap_table_size equal Reduce your SELECT DISTINCT queries without LIMIT clauses Increase table_cache gradually to avoid file descriptor limits Your applications are not closing MySQL connections properly Variables to adjust: query_cache_limit (> 1M, or use smaller result sets) tmp_table_size (> 16M) max_heap_table_size (> 16M) table_cache (> 64) innodb_buffer_pool_size (>= 326M) For the variables that it recommends that I adjust, I don't even see most of them in the mysql.cnf file. [client] port = 3306 socket = /var/run/mysqld/mysqld.sock [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_buffer_pool_size = 220M innodb_flush_log_at_trx_commit = 2 innodb_file_per_table = 1 innodb_thread_concurrency = 32 skip-locking big-tables max_connections = 50 innodb_lock_wait_timeout = 600 slave_transaction_retries = 10 innodb_table_locks = 0 innodb_additional_mem_pool_size = 20M user = mysql socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /var/lib/mysql tmpdir = /tmp skip-external-locking bind-address = localhost key_buffer = 16M max_allowed_packet = 16M thread_stack = 192K thread_cache_size = 4 myisam-recover = BACKUP query_cache_limit = 1M query_cache_size = 16M log_error = /var/log/mysql/error.log expire_logs_days = 10 max_binlog_size = 100M skip-locking innodb_file_per_table = 1 big-tables [mysqldump] quick quote-names max_allowed_packet = 16M [mysql] [isamchk] key_buffer = 16M !includedir /etc/mysql/conf.d/

  Read the article

• How to find what files / directories are not copied yet?

  - by user8676

  Hi all, I found the following 'nice' situation: An archive of few disks (actually three disks) which has a bunch of photos (more or less) organized. Well, this is good. A big disk shared on a network which has a bunch of photos which has another folder structure (even if is somewhat recognizable for a human being) than the archive described above, but some of the files on this big network share are the same with the files from the archive. Well, this is bad. What we need is to move the different (new) files from the network share in the archive (perhaps we'll use for this a new disk added to archive). The program that we need is different from a regular File Duplicate Finder program because usually the File Duplicate Finder finds the duplicates from all sources comparing each file with another. We want to find the differences between the two sources. It is fine for us to have a report generated in text file which after this we'll use to do our move. A Windows solution will be preferred. Any ideas? TIA

  Read the article

• Difference between all servers in one cluster and more than one cluster with servers?

  - by silla

  Not sure I understand what´s the difference or how it works when servers a running in one cluster or if there are more than one clusters with servers in it - regard High availability & Load Balancing. For me they are somehow the same, there is not really a big difference. Let´s make a simple example: 2 Servers in 1 Cluster 2 Clusters with each 1 Server - 1. If one Server failure, the other one is able to continue the work. The same for Load Balancing, these two Servers are able to balance the work together. - 2. The same thing! If one Server failure... The only thing that could be a problem with point 1. is if the Cluster fails (then both of the Server are dead). But is this even possible? I was reading stuff about clustering and high availability but I think I do not get this really. Probably I did not really understand how a cluster is working. Are these 2 points with 1 Cluster and 2 Clusters somehow the same or are there really some big differences? What should I know about it? Thank you

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by user57019

  I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

• Ubuntu server 10.04 disconnects after short periods of inactivity on my site

  - by Melot

  Hi! I'm new to Ubuntu (installed it for the first time just a couple of days ago on my server). I've Ubuntu Server 10.04 and am just using the terminal, no GUI like Gnome. So far it's working pretty great except for one big thing. Whenever I go to sleep and there's no activity on my server (it's not a big site so active users drop to 0 during the night), the server kind of disconnects. The only thing that can bring the site back online is to restart the whole server. I've tried disabling powersaving by using setterm but that changes nothing. Even if I wake up the server by pressing any key or so the site wont go back online! I've tried just restarting both Apache and MySQL (I'm using LAMP-server btw) but not even that works. But as soon as I turn the power off and on at the server, everythings work like normal for a couple of minutes of inactivity (~5-15 minutes I'd guess) and then it's down again unless someone logs in to the site and is active. I was previously using XAMPP on my laptop with Windows XP and that worked 24/7 so I don't think it's anything with my router or ISP. This is driving me crazy! My site is down all the time I'm in school as I have no possibility to restart the server if it becomes offline. Does anyone have a clue to what could be wrong?

  Read the article

• Windows 7, network transmit (send) not working

  - by user326287

  My Win 7 works 2 years without problem. But now, I can't transmit (send) big data on LAN/Internet. I can: - Ping anything - Browse Internet, download files at full speed - Send e-mails with very small attachments. - Testing download speed on Speedtest.net, measure stable full speed. I can't: - Testing upload speed on Speedtest.net. Upload stuck.. - Save/send email messages with big (128k) attachment, independent from e-mail provider or e-mail box. THIS IS NOT A HARDWARE/CABLE/CARD OR OTHER NETWORK DEVICES PROBLEM! When I boot from a Linux Live CD, without ANY hardware change, all data sending, testing works correctly, at full speed. I have tried already in Win 7: - Disable Windows/3rd party Firewall completely - Reset IP stack parameters (netsh int ip reset c:\resetlog.txt) - Computer restore - Reinstall LAN driver When I inspect the packets in Wireshark in Windows, I see lot's of (maybe 60% of sent packets) "TCP Retransmission". Sometimes receive "TCP Dup Ack" or "TCP Out-of-Order". Linux don't do this. Thank you for the help.

  Read the article

• Jabber client for windows 7

  - by Anders

  I am looking for a jabber client with some specific functions. I have spent 1½ day looking for one and it is getting tiresome. Clients that I have been using, that have what I need, but I am not interesting for a reason in are: Pidgin, does not show complete messages in their popups. Miranda IM, I have a constant disconnect issue that does not seem to be resolved in my case. What I need are: Popups A popup that shows broadcasts to users. A popup that show when my username is typed in a conference chat. I need to be able to view the full message in the popup. No configuration of a theme to make this enabled, or if there is a working theme for it already. Preferable placement is on the top right of the screen. Able to 'popup' when running full screen applications, much like games. Conferences Easy access to bookmarked conferences. I do not want to go through submenus to rejoin a disconnected or closed conference. If I close the conference window I want to be connected to the conference until I exit the client. Tabbed interface. Configuration Sober configurations, options are great but there is a limit and the above needs to be availble in the options in a understandable manner. What I wish for: MSN Not needed! If it is avaible then it is a big plus. Facebook Not needed! If it is avaible then it is a big plus. Conferences/chats Not needed! Eyecandy is always nice.

  Read the article

• Deploying Memcached as 32bit or 64bit?

  - by rlotun

  I'm curious about how people deploy memcached on 64 bit machines. Do you compile a 64bit (standard) memcached binary and run that, or do people compile it in 32bit mode and run N instances (where N = machine_RAM / 4GB)? Consider a recommended deployment of Redis (from the Redis FAQ): Redis uses a lot more memory when compiled for 64 bit target, especially if the dataset is composed of many small keys and values. Such a database will, for instance, consume 50 MB of RAM when compiled for the 32 bit target, and 80 MB for 64 bit! That's a big difference. You can run 32 bit Redis binaries in a 64 bit Linux and Mac OS X system without problems. For OS X just use make 32bit. For Linux instead, make sure you have libc6-dev-i386 installed, then use make 32bit if you are using the latest Git version. Instead for Redis <= 1.2.2 you have to edit the Makefile and replace "-arch i386" with "-m32". If your application is already able to perform application-level sharding, it is very advisable to run N instances of Redis 32bit against a big 64 bit Redis box (with more than 4GB of RAM) instead than a single 64 bit instance, as this is much more memory efficient. Would not the same recommendation also apply to a memcached cluster?

  Read the article

• Macports Apache not starting at Mac osx snow leopard boot

  - by greg

  Macports Apache2 not starting at Mac Osx snow leopard boot. I've done the launchctl load command, the symlinks point to my /opt/local//etc/LaunchDaemeons/org.macports.apache2/org.macports.apache2.plist, but it never starts. I can start it manually, works fine after that. Just wont load on startup. My server is named in my /opt/localapache2/conf/httd.conf, I had read that sometimes makes a difference. I've done the launchctl unload and load trick, al with no results. I'm out of ideas.

  Read the article

• Macports Apache not starting at Mac osx snow leopard boot

  - by greg

  Macports Apache2 not starting at Mac Osx snow leopard boot. I've done the launchctl load command, the symlinks point to my /opt/local//etc/LaunchDaemeons/org.macports.apache2/org.macports.apache2.plist, but it never starts. I can start it manually, works fine after that. Just wont load on startup. My server is named in my /opt/localapache2/conf/httd.conf, I had read that sometimes makes a difference. I've done the launchctl unload and load trick, al with no results. I'm out of ideas.

  Read the article

• How to install libv8 using a specific version of g++?

  - by Catfish

  I'm trying to install therubyracer gem for a rails project - http://stackoverflow.com/questions/13793533/unable-to-install-therubyracer-on-centos-errors-with-v8-and-gcc and i'm thinking that now that i installed g++44, that all i need to do is get gem install libv8 to use g++44 instead of g++. Is there a way to run gem install libv8 and to have it look at my updated g++ version? Or is there a way to set the default g++ to the g++44 location? some helpful output [root@allthingswebdesign current]# which g++ /usr/bin/g++ [root@allthingswebdesign current]# which g++44 /usr/bin/g++44 [root@allthingswebdesign current]# [root@allthingswebdesign current]# cd /usr/bin/ [root@allthingswebdesign bin]# ls -al g++* -rwxr-xr-x 4 root root 218432 May 10 2012 g++ -rwxr-xr-x 2 root root 263704 Feb 21 2012 g++44 lrwxrwxrwx 1 root root 12 Dec 9 17:21 g++-4.4 -> /usr/bin/g++

  Read the article

• Install Glibc2 using Yum

  - by Nerrve

  I'm trying to install glibc2 version 2.11 that's needed for openoffice 3.4 https://issues.apache.org/ooo/show_bug.cgi?id=119393 but i can't seem to find the dependency with yum. I already have the following dependencies installed. glibc.i686 2.5-49.el5_5.7 installed glibc.x86_64 2.5-49.el5_5.7 installed glibc-common.x86_64 2.5-49.el5_5.7 installed glibc-devel.x86_64 2.5-49.el5_5.7 installed glibc-headers.x86_64 2.5-49.el5_5.7 installed libc-client.x86_64 2004g-2.2.1 installed and glibc.i686 2.5-81.el5_8.2 updates glibc.x86_64 2.5-81.el5_8.2 updates glibc-common.x86_64 2.5-81.el5_8.2 updates glibc-devel.i386 2.5-81.el5_8.2 updates glibc-devel.x86_64 2.5-81.el5_8.2 updates glibc-headers.x86_64 2.5-81.el5_8.2 updates glibc-utils.x86_64 2.5-81.el5_8.2 updates I ran the following to get the version but it shows something different [root@***** /]# ./lib64/libc.so.6 GNU C Library stable release version 2.5, by Roland McGrath et al. Can someone please help? Thanks! EDIT : I'm using CentOS 2.6.18-128.1.10.el5

  Read the article

• Improper output in SSH session on OSX using FreeSSHd on Windows with cygwin bash/sh shell

  - by Tyler Clendenin

  I am testing out running an SSH server on a local Windows VM. I have installed FreeSSHd and set the command shell to "c:\cygwin\bin\sh --login -i" (bash as well) with "Use new console engine" unchecked. (When it was enabled no output would show through the ssh connection anyway) The shell seems to work, but when connecting from my OS-X terminal using ssh all of the shell results comes out ill formatted. $ ls -al total 17 drwxr-xr-x+ 1 SYSTEM Administrators 4096 Feb 2 01:00 . drwxrwxrwt+ 1 Administrator Administrators 0 Feb 2 01:01 .. -rw------- 1 SYSTEM Administrators 128 Feb 2 01:30 .bash_history -rwxr-xr-x 1 SYSTEM Administrators 1150 Feb 2 00:55 .bash_profile -rwxr-xr-x 1 SYSTEM Administrators 3754 Feb 2 00:55 .bashrc -rwxr-xr-x 1 SYSTEM Administrators 1461 Feb 2 00:55 .inputrc Any ideas on why this is happening, how I can fix this?

  Read the article

• httpd not starting with systemd on F17

  - by malfy

  Title says it all. This is a fresh Fedora 17 system running on a Xen hypervisor. No idea why it won't start [root@box~]  uname -a Linux box.localhost 3.5.4-2.fc17.i686.PAE #1 SMP Wed Sep 26 22:10:23 UTC 2012 i686 i686 i386 GNU/Linux [root@box~]  cat /etc/redhat-release Fedora release 17 (Beefy Miracle) [root@box~]  systemctl enable httpd.service ln -s '/usr/lib/systemd/system/httpd.service' '/etc/systemd/system/multi-user.target.wants/httpd.service' [root@box~]  systemctl start httpd.service Job failed. See system journal and 'systemctl status' for details. [root@box~]  systemctl status httpd.service httpd.service - The Apache HTTP Server (prefork MPM) Loaded: loaded (/usr/lib/systemd/system/httpd.service; enabled) Active: failed (Result: exit-code) since Fri, 19 Oct 2012 22:43:37 -0500; 3s ago Process: 18225 ExecStart=/usr/sbin/httpd $OPTIONS -k start (code=exited, status=226/NAMESPACE) CGroup: name=systemd:/system/httpd.service Oct 19 22:43:37 box.localhost systemd[18225]: Failed at step NAMESPACE spawning /usr/sbin/httpd: No such file or directory [root@box~]  ls -al /usr/sbin/httpd -rwxr-xr-x 1 root root 343496 Apr 30 04:56 /usr/sbin/httpd

  Read the article

• Ethernet interface number changed, and old one does not exist, but does not leave IP address

  - by Sagar

  I have a virtual machine with Mandriva 2007.0 (yes, old - unfortunately we do not have a choice here). Anyway, the problem: Before reboot: active network interface = eth0. No other interfaces present, and network manager confirms this. Static IP address set to 172.31.2.22. No issues, everything working properly, routing et al. -------Reboot--------- After reboot: active network interface = eth1, with a DHCP address. Network manager shows eth0 as disconnected, and not connectable. When I try to set eth1 up with the static IP address (same one), it says "In Use". I then tried ifconfig eth0 172.31.2.29 just to free it up from the eth0 interface so I could use it with eth1 (since this is connected). Result: ifconfig eth0 172.31.2.29 SIOCSIFADDR: No such device eth0: unknown interface: No such device Nothing else changed. Any ideas what could be happening, or at least how I can get my IP address back?

  Read the article

• Is RAID 0 or JBOD better for home media server?

  - by Donald Hughes

  I have an external two-bay drive enclosure (the OWC Mercury Elite-AL Pro) connected to a Mac Mini (my home media server) over FireWire 800. I'm streaming media to other computers in the house over wired gigabit. I have two 1.5 TB drives that I'm using independently right now. The media is on one, and I'm mirroring the files to the other drive at night as a backup. But as I approach filling up the drive I'm wanting to span those two drives together to give me a total of about 3 TB, and then buy another drive for backups. The external enclosure supports both RAID 0 and JBOD, but I'm not clear on which would be better in this situation. Would RAID 0 provide any performance improvements over JBOD for streaming video (possibly several streams at once? How does each affect the MTBF of the drives? In general, should I choose RAID 0, JBOD, or keep them independent?

  Read the article

• directory listing on Mac OS X

  - by user27150

  I dumped a bunch of files (music and otherwise) onto my shiny new Macbook, and since I'm more comfortable with linux than Mac (at this point) I tend to use the terminal. I did a ls -al on the files I'd transfered, and some had an "@" at the end of the permissions string, and some did not. Something like: drwxrwxr--@ 93 user staff etc. drwxrwxr-- 107 user staff etc. The ones without "@" could be seen in Finder and accessed by other programs-- the "@" files and directories were invisible. Can anyone explain what the "@" means, and how to chmod (or whatever) so I can use these files? I assume it is some sort of system flag but I don't know how to unset it. Chmod 777 had no effect and I already own the files. Thanks

  Read the article

• MySQL dump, output each table row on a new line whilst using --extended-insert

  - by soopadoubled

  I'm having an issue, where for ease of use, I'd like to be able to format a command line MySQL dump so that each row of a given table is on a new line when using the --extended-insert option. Usually when using --extended-insert, every row of a given table is outputted on one line, and as far as I am aware there's no way to change this, other than post-processing the dump with perl or such like. The format I'm looking for is: -- -- Dumping data for table `ww_tbCountry` -- INSERT INTO `ww_tbCountry` (`iCountryId_PK`, `vCountryName`, `vShortName`, `iSortFlag`, `fTax`, `vCountryCode`, `vSageTaxCode`) VALUES (22, 'Albania', 'AL', 1, 0.00, '8', 'T9'), (33, 'Austria', 'AT', 1, 15.00, '40', 'T9'), (40, 'Belarus', 'BY', 1, 0.00, '112', 'T9'), (41, 'Belgium', 'BE', 1, 15.00, '56', 'T9'), (51, 'Bulgaria', 'BG', 1, 15.00, '100', 'T9' However, when I dump a database using Phpmyadmin, using --extended-insert, each row is dumped on a new line (as shown by the example above). I've gone through Phpmyadmin and can't find any documentation that would explain this. Is anyone able to shed any light on this? Thanks in advance, Ian

  Read the article

• Improper output in SSH session on OSX using FreeSSHd on Windows with cygwin bash/sh shell

  - by Tyler Clendenin

  I am testing out running an SSH server on a local Windows VM. I have installed FreeSSHd and set the command shell to "c:\cygwin\bin\sh --login -i" (bash as well) with "Use new console engine" unchecked. (When it was enabled no output would show through the ssh connection anyway) The shell seems to work, but when connecting from my OS-X terminal using ssh all of the shell results comes out ill formatted. $ ls -al total 17 drwxr-xr-x+ 1 SYSTEM Administrators 4096 Feb 2 01:00 . drwxrwxrwt+ 1 Administrator Administrators 0 Feb 2 01:01 .. -rw------- 1 SYSTEM Administrators 128 Feb 2 01:30 .bash_history -rwxr-xr-x 1 SYSTEM Administrators 1150 Feb 2 00:55 .bash_profile -rwxr-xr-x 1 SYSTEM Administrators 3754 Feb 2 00:55 .bashrc -rwxr-xr-x 1 SYSTEM Administrators 1461 Feb 2 00:55 .inputrc Any ideas on why this is happening, how I can fix this?

  Read the article

• Project management software that syncs with smartphone?

  - by overtherainbow

  Hello, I went through the archives here and the Wikipedia page on Project management software, but didn't find information on this type of application to manage projects: Native Windows application (don't like web-based solutions; prefer native to cross-platform) Free or affordable, ie. not an Enterprise solution Scalable from one to a few concurrent users Like MS Projet et al., a project consists in tasks which can be further divided into sub-tasks, and the whole thing is displayed in an tree list An item that has a date set (either start/due) must be displayed in a Calendar view, so it's easy to know what work must be done each day The Calendar view must somehow sync with smartphones (at least BlackBerry) At this point, the apps I know either don't provide a Calendar at all, or do but they can't sync with smartphones, which forces me to copy/paste scheduled items into Outlook so they are synced with my BlackBerry :-/ Thank you for any help.

  Read the article

• How do I restore my system from a "Backup and Restore Center" backup?

  - by Daniel R Hicks

  The Windows (Vista) documentation and available online info is comprehensively vague. If I have a moderately brain dead system and want to restore it, and I have a "Backup and Restore Center" backup whose "delta" is not quite a week old (but with a "full backup" behind it), what steps do I go through to recover my box back to that backup point? It's totally unclear whether simply doing "restore all" from the (advanced) "Center" is sufficient, or do I need to first take the box back to day zero with the system restore DVD, et al? (Just editing this to get my correct ID associated with it.)

  Read the article

• Weird bug in 'tar' not including files named .__init__.py

  - by Sridhar Ratnakumar

  Does anyone know why tar is not including files named .__init__.py (note the dot)? $ mkdir /tmp/work && cd /tmp/work $ mkdir foo $ touch foo/.__init__.py $ touch foo/.namespace__init__.py $ tar czf foo.tar.gz foo $ mkdir e && mv foo.tar.gz e/ && cd e/ $ tar zxf foo.tar.gz $ ls -al foo/ total 0 drwxr-xr-x 2 sridharr wheel 102 14 Mar 17:16 . drwxr-xr-x 3 sridharr wheel 136 14 Mar 17:17 .. -rw-r--r-- 1 sridharr wheel 0 14 Mar 17:16 .namespace__init__.py $ $ echo ".__init__.py file is missing. WTF? This is OSX 10.6"

  Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >