Search Results

Search found 4534 results on 182 pages for 'dns q'.

Page 93/182 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

• Creating static NAT blocks outbound traffic Cisco ASA

  - by natediggs

  Hi Everyone, I have two web servers sitting behind a Cisco ASA 5505, which I don't have much experience with. I'm trying to create two static NATs. One static NAT that goes to xx.xx.xx.150 and another that goes to xx.xx.xx.151. I've created the static NAT for the .150 web server and it works FINE. Incoming and outgoing traffic work great. This is the staging web server. I now need to duplicate the setup for the production web server. So, I connect the webserver to the firewall, change the public IP address on one of the NICs reboot the server and I have outbound internet access. Then I run the command: static (inside,outside) xx.xx.xx.150 192.168.1.x which is successful. I then run the command: access-list acl-outside permit tcp any host xx.xx.xx.150 eq 80 Which is successful. I then try to browse the internet and I get nothing. I try to telnet in through port 80 and I get nothing (though I'm guessing because the response to the telnet request is being blocked). I've tried this with the production web server and then I tried it with another web server that is for internal testing and have the exact same problem. Both work fine until I run the static NAT rule and then no outbound internet access. I have a feeling that it's something simple that I'm missing, but my limited experience with this device is killing me. Below I've pasted the current configuration. I'm currently trying to get this to work on the .153 server which is the internal testing server. Once I can verify that works, I'll try it with production. : Saved : ASA Version 8.2(4) ! hostname QG domain-name XX.com enable password passwd names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address XX.XX.XX.148 255.255.255.0 ! interface Vlan3 shutdown no forward interface Vlan1 nameif dmz security-level 50 ip address dhcp ! boot system disk0:/asa824.bin ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name fw.XXgroup.com same-security-traffic permit inter-interface access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.150 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq www access-list acl-outside extended permit tcp any host XX.XX.XX.151 eq https access-list acl-outside extended permit tcp any host XX.XX.XX.153 eq www access-list inside_access_in extended permit ip 192.168.1.0 255.255.255.0 any access-list inside_nat0_outbound extended permit ip any 192.168.1.32 255.255.255.240 pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 mtu dmz 1500 ip local pool VPNIPs 192.168.1.35-192.168.1.44 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-635.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) XX.XX.XX150 192.168.1.100 netmask 255.255.255.255 static (inside,outside) XX.XX.XX153 192.168.1.102 netmask 255.255.255.255 access-group acl-outside in interface outside route outside 0.0.0.0 0.0.0.0 XX.XX.XX129 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authorization command LOCAL http server enable http 192.168.1.0 255.255.255.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group1 crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication crack encryption 3des hash sha group 2 lifetime 86400 no crypto isakmp nat-traversal client-update enable telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd dns 208.77.88.4 interface inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn enable outside svc image disk0:/sslclient-win-1.1.0.154.pkg 1 svc image disk0:/anyconnect-win-2.5.2019-k9.pkg 2 svc enable group-policy ATSAdmin internal group-policy ATSAdmin attributes dns-server value 208.77.88.4 208.85.174.9 vpn-tunnel-protocol IPSec svc webvpn webvpn url-list none svc keep-installer installed svc rekey method ssl svc ask enable username qgadmin password /oHfeGQ/R.bd3KPR encrypted privilege 15 username benl password 0HNIGQNI0uruJvhW encrypted privilege 0 username benl attributes vpn-group-policy ATSAdmin username kuzma password rH7MM7laoynyvf9U encrypted privilege 0 username kuzma attributes vpn-group-policy ATSAdmin username nate password BXHOURyT37e4O5mt encrypted privilege 0 username nate attributes vpn-group-policy ATSAdmin tunnel-group ATSAdmin type remote-access tunnel-group ATSAdmin general-attributes address-pool VPNIPs default-group-policy ATSAdmin tunnel-group SSLVPN type remote-access tunnel-group SSLVPN general-attributes address-pool VPNIPs default-group-policy ATSAdmin ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global privilege cmd level 3 mode exec command perfmon privilege cmd level 3 mode exec command ping privilege cmd level 3 mode exec command who privilege cmd level 3 mode exec command logging privilege cmd level 3 mode exec command failover privilege show level 5 mode exec command running-config privilege show level 3 mode exec command reload privilege show level 3 mode exec command mode privilege show level 3 mode exec command firewall privilege show level 3 mode exec command interface privilege show level 3 mode exec command clock privilege show level 3 mode exec command dns-hosts privilege show level 3 mode exec command access-list privilege show level 3 mode exec command logging privilege show level 3 mode exec command ip privilege show level 3 mode exec command failover privilege show level 3 mode exec command asdm privilege show level 3 mode exec command arp privilege show level 3 mode exec command route privilege show level 3 mode exec command ospf privilege show level 3 mode exec command aaa-server privilege show level 3 mode exec command aaa privilege show level 3 mode exec command crypto privilege show level 3 mode exec command vpn-sessiondb privilege show level 3 mode exec command ssh privilege show level 3 mode exec command dhcpd privilege show level 3 mode exec command vpn privilege show level 3 mode exec command blocks privilege show level 3 mode exec command uauth privilege show level 3 mode configure command interface privilege show level 3 mode configure command clock privilege show level 3 mode configure command access-list privilege show level 3 mode configure command logging privilege show level 3 mode configure command ip privilege show level 3 mode configure command failover privilege show level 5 mode configure command asdm privilege show level 3 mode configure command arp privilege show level 3 mode configure command route privilege show level 3 mode configure command aaa-server privilege show level 3 mode configure command aaa privilege show level 3 mode configure command crypto privilege show level 3 mode configure command ssh privilege show level 3 mode configure command dhcpd privilege show level 5 mode configure command privilege privilege clear level 3 mode exec command dns-hosts privilege clear level 3 mode exec command logging privilege clear level 3 mode exec command arp privilege clear level 3 mode exec command aaa-server privilege clear level 3 mode exec command crypto privilege cmd level 3 mode configure command failover privilege clear level 3 mode configure command logging privilege clear level 3 mode configure command arp privilege clear level 3 mode configure command crypto privilege clear level 3 mode configure command aaa-server prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily Cryptochecksum:0ed0580e151af288d865f4f3603d792a : end asdm image disk0:/asdm-635.bin no asdm history enable

  Read the article

• Python CGI on Amazon AWS EC2 micro-instance -- a how-to!

  - by user595585

  How can you make an EC2 micro instance serve CGI scripts from lighthttpd? For instance Python CGI? Well, it took half a day, but I have gotten Python cgi running on a free Amazon AWS EC2 micro-instance, using the lighttpd server. I think it will help my fellow noobs to put all the steps in one place. Armed with the simple steps below, it will take you only 15 minutes to set things up! My question for the more experienced users reading this is: Are there any security flaws in what I've done? (See file and directory permissions.) Step 1: Start your EC2 instance and ssh into it. [Obviously, you'll need to sign up for Amazon EC2 and save your key pairs to a *.pem file. I won't go over this, as Amazon tells you how to do it.] Sign into your AWS account and start your EC2 instance. The web has tutorials on doing this. Notice that default instance-size that Amazon presents to you is "small." This is not "micro" and so it will cost you money. Be sure to manually choose "micro." (Micro instances are free only for the first year...) Find the public DNS code for your running instance. To do this, click on the instance in the top pane of the dashboard and you'll eventually see the "Public DNS" field populated in the bottom pane. (You may need to fiddle a bit.) The Public DNS looks something like: ec2-174-129-110-23.compute-1.amazonaws.com Start your Unix console program. (On Max OS X, it's called Terminal, and lives in the Applications - Utilities folder.) cd to the directory on your desktop system that has your *.pem file containing your AWS keypairs. ssh to your EC2 instance using a command like: ssh -i <<your *.pem filename>> ec2-user@<< Public DNS address >> So, for me, this was: ssh -i amzn_ec2_keypair.pem [email protected] Your EC2 instance should let you in. Step 2: Download lighttpd to your EC2 instance. To install lighttpd, you will need root access on your EC2 instance. The problem is: Amazon will not let you sign in as root. (Not straightforwardly, at least.) But there is a workaround. Type this command: sudo /bin/bash The system prompt-character will change from $ to #. We won't exit from "sudo" until the very last step in this whole process. Install the lighttpd application (version 1.4.28-1.3.amzn1 for me): yum install lighttpd Install the FastCGI libraries for lighttpd (not needed, but why not?): yum install lighttpd-fastcgi Test that your server is working: /etc/init.d/lighttpd start Step 3: Let the outside world see your server. If you now tried to hit your server from the browser on your desktop, it would fail. The reason: By default, Amazon AWS does not open any ports to your EC2 instance. So, you have to open the ports manually. Go to your EC2 dashboard in your desktop's browser. Click on "Security Groups" in the left pane. One or more security groups will appear in the upper right pane. Choose the one that was assigned to your EC2 instance when you launched your instance. A table called "Allowed Connections" will appear in the lower right pane. A pop-up menu will let you choose "HTTP" as the connection method. The other values in that line of the table should be: tcp, 80, 80, 0.0.0.0/0 Now hit your EC2 instance's server from the desktop in your browser. Use the Public DNS address that you used earlier to SSH in. You should see the lighttpd generic web page. If you don't, I can't help you because I am such a noob. :-( Step 4: Configure lighttpd to serve CGI. Back in the console program, cd to the configuration directory for lighttpd: cd /etc/lighttpd To enable CGI, you want to uncomment one line in the < modules.conf file. (I could have enabled Fast CGI, but baby steps are best!) You can do this with the "ed" editor as follows: ed modules.conf /include "conf.d\/cgi.conf"/ s/#// w q Create the directory where CGI programs will live. (The /etc/lighttpd/lighttpd.conf file determines where this will be.) We'll create our directory in the default location, so we don't have to do any editing of configuration files: cd /var/www/lighttpd mkdir cgi-bin chmod 755 cgi-bin Almost there! Of course you need to put a test CGI program into the cgi-bin directory. Here is one: cd cgi-bin ed a #!/usr/bin/python print "Content-type: text/html\n\n" print "<html><body>Hello, pyworld.</body></html>" . w hellopyworld.py q chmod 655 hellopyworld.py Restart your lighttpd server: /etc/init.d/lighttpd restart Test your CGI program. In your desktop's browser, hit this URL, substituting your EC2 instance's public DNS address: http://<<Public DNS>>/cgi-bin/hellopyworld.py For me, this was: http://ec2-174-129-110-23.compute-1.amazonaws.com/cgi-bin/hellopyworld.py Step 5: That's it! Clean up, and give thanks! To exit from the "sudo /bin/bash" command given earlier, type: exit Acknowledgements: Heaps of thanks to: wiki.vpslink.com/Install_and_Configure_lighttpd www.cyberciti.biz/tips/lighttpd-howto-setup-cgi-bin-access-for-perl-programs.html aws.typepad.com/aws/2010/06/building-three-tier-architectures-with-security-groups.html Good luck, amigos! I apologize for the non-traditional nature of this "question" but I have gotten so much help from Stackoverflow that I was eager to give something back.

  Read the article

• Windows periodically disconnects, reconnects to the network

  - by einpoklum

  My setup: I have a PC with a Gigabyte GA-MA78S2H motherboard (Realtek Gigabit wired Ethernet on-board). I have the latest drivers (at least the latest driver for the NIC. I'm connecting via an Edimax BR-6216Mg (again, wired connection). For some reason I experience short periodic disconnects and reconnects. Specifically, Skype disconnects, tries to connect, succeeds after a short while; incoming SFTP sessions get dropped; using a browser, I sometime get stuck in the DNS lookup or connection to the website and a page won't load. A couple of seconds later, a reload works. All this happens with Windows XP SP3. With Windows 7, it also happens. (When I initially wrote this question I didn't notice it.) ipconfig for my adapter: Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 00-1D-7D-E9-72-9E Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.0.2 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.254 DHCP Server . . . . . . . . . . . : 192.168.0.254 DNS Servers . . . . . . . . . . . : 192.117.235.235 62.219.186.7 Lease Obtained. . . . . . . . . . : Saturday, March 10, 2012 8:28:20 AM Lease Expires . . . . . . . . . . : Friday, January 26, 1906 2:00:04 AM A result of some tests a couple of the disconnects: C:\Documents and Settings\eyalroz.BAKNUNIN>nslookup google.com DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 192.117.235.235: Timed out DNS request timed out. timeout was 2 seconds. *** Can't find server name for address 62.219.186.7: Timed out *** Default servers are not available Server: UnKnown Address: 192.117.235.235 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. *** Request to UnKnown timed-out C:\Documents and Settings\eyalroz.BAKNUNIN>ping 194.90.1.5 Pinging 194.90.1.5 with 32 bytes of data: Control-C ^C C:\Documents and Settings\eyalroz.BAKNUNIN>tracert -d 194.90.1.5 Tracing route to 194.90.1.5 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.0.254 2 * * 11 ms 10.168.128.1 3 14 ms 13 ms 14 ms 212.179.160.142 4 * * * Request timed out. 5 * * * Request timed out. 6 * * 47 ms 62.219.189.169 7 31 ms 27 ms 32 ms 62.219.189.150 8 15 ms 14 ms 16 ms 192.114.65.202 9 15 ms 15 ms 11 ms 212.143.10.66 10 13 ms 29 ms 31 ms 212.143.12.234 11 35 ms 15 ms 18 ms 212.143.8.72 12 22 ms 22 ms 16 ms 194.90.1.5 I usually ping 194.90.1.5 (which is not at my ISP) with 15ms response time and no losses. Things I've done/tried: [2012-03-26] I replaced the cable; I thought that made a difference, but the disconnects were back a while later, so that wasn't it. Updated the NIC driver. Tried reducing the MTU (used a utility called Dr. TCP); there was no effect. I updated my board BIOS revision (which caused all the HW to be "reinstalled" or re-identified - successfully). I installed another NIC, and tried switching to it - same effect with the on-board NIC. A while back I tried another router (although it was an Edimax model) - same problem. Connected the computer directly, with no router. Same problem. ping -t to the router (192.168.0.254) gives pongs, nothing is lost, and time is < 1 ms almost always (sometimes it says 1 or 2 ms). This is the case also during the disconnects.

  Read the article

• DKIM, SPF, PTR records are not working properly with my domain

  - by shihon

  I configured my server and well authenticate email system with DKIM key, SPF record and PTR records, when i start to sent out mails from phplist interface to my users ~50000, my domain is spammed by google. In headers, signed by and mailed by tag shows by my domain : appmail.co, I also test my domain via check mail provide by port25, report is: This message is an automatic response from Port25's authentication verifier service at verifier.port25.com. The service allows email senders to perform a simple check of various sender authentication mechanisms. It is provided free of charge, in the hope that it is useful to the email community. While it is not officially supported, we welcome any feedback you may have at . Thank you for using the verifier, The Port25 Solutions, Inc. team ========================================================== Summary of Results SPF check: pass DomainKeys check: neutral DKIM check: pass Sender-ID check: pass SpamAssassin check: ham ========================================================== Details: HELO hostname: app.appmail.co Source IP: 108.179.192.148 mail-from: [email protected] SPF check details: Result: pass ID(s) verified: [email protected] DNS record(s): appmail.co. SPF (no records) appmail.co. 14400 IN TXT "v=spf1 +a +mx +ip4:108.179.192.148 ?all" appmail.co. 14400 IN A 108.179.192.148 DomainKeys check details: Result: neutral (message not signed) ID(s) verified: [email protected] DNS record(s): DKIM check details: Result: pass (matches From: [email protected]) ID(s) verified: header.d=appmail.co Canonicalized Headers: content-type:multipart/alternative;'20'boundary=047d7b2eda75d8544d04c17b6841'0D''0A' to:[email protected]'0D''0A' from:shashank'20'sharma'20'<[email protected]>'0D''0A' subject:Test'0D''0A' message-id:<CADnDhbH9aDBk3Ho2-CrG7gwOoD6RNX0sFq4bWL64+kmo=9HjWg@mail.gmail.com>'0D''0A' date:Sat,'20'2'20'Jun'20'2012'20'16:44:50'20'+0530'0D''0A' mime-version:1.0'0D''0A' dkim-signature:v=1;'20'a=rsa-sha256;'20'q=dns/txt;'20'c=relaxed/relaxed;'20'd=appmail.co;'20's=default;'20'h=Content-Type:To:From:Subject:Message-ID:Date:MIME-Version;'20'bh=GS6uwlT+weKcrrLJ2I+cjBtWPq9nvhwRlNAJebOiQOk=;'20'b=; Canonicalized Body: --047d7b2eda75d8544d04c17b6841'0D''0A' Content-Type:'20'text/plain;'20'charset=UTF-8'0D''0A' '0D''0A' Hello'20'Senders'0D''0A' '0D''0A' --047d7b2eda75d8544d04c17b6841'0D''0A' Content-Type:'20'text/html;'20'charset=UTF-8'0D''0A' '0D''0A' Hello'20'Senders'0D''0A' '0D''0A' --047d7b2eda75d8544d04c17b6841--'0D''0A' DNS record(s): default._domainkey.appmail.co. 14400 IN TXT "v=DKIM1; k=rsa; p=MHwwDQYJKoZIhvcNAQEBBQADawAwaAJhALGCOdMeZRxRHoatH7/KCvI1CKS0wOOsTAq0LLgPsOpMolifpVQDKOWT2zq/6LHVmDVjXLbnWO2d4ry/riy7ei66pLpnAV5ceIUSjBRusI8jcF9CZhPrh/OImsKVUb9ceQIDAQAB;" NOTE: DKIM checking has been performed based on the latest DKIM specs (RFC 4871 or draft-ietf-dkim-base-10) and verification may fail for older versions. If you are using Port25's PowerMTA, you need to use version 3.2r11 or later to get a compatible version of DKIM. Sender-ID check details: Result: pass ID(s) verified: [email protected] DNS record(s): appmail.co. SPF (no records) appmail.co. 14400 IN TXT "v=spf1 +a +mx +ip4:108.179.192.148 ?all" appmail.co. 14400 IN A 108.179.192.148 SpamAssassin check details: SpamAssassin v3.3.1 (2010-03-16) Result: ham (-0.1 points, 5.0 required) pts rule name description ---- ---------------------- -------------------------------------------------- -0.0 T_RP_MATCHES_RCVD Envelope sender domain matches handover relay domain 0.0 HTML_MESSAGE BODY: HTML included in message -0.5 BAYES_05 BODY: Bayes spam probability is 1 to 5% [score: 0.0288] -0.1 DKIM_VALID_AU Message has a valid DKIM or DK signature from author's domain 0.1 DKIM_SIGNED Message has a DKIM or DK signature, not necessarily valid -0.1 DKIM_VALID Message has at least one valid DKIM or DK signature 0.5 SINGLE_HEADER_1K A single header contains 1K-2K characters ========================================================== Original Email Return-Path: <[email protected]> Received: from app.appmail.co (108.179.192.148) by verifier.port25.com id hp7qqo11u9cc for <[email protected]>; Sat, 2 Jun 2012 07:14:52 -0400 (envelope-from <[email protected]>) Authentication-Results: verifier.port25.com; spf=pass [email protected] Authentication-Results: verifier.port25.com; domainkeys=neutral (message not signed) [email protected] Authentication-Results: verifier.port25.com; dkim=pass (matches From: [email protected]) header.d=appmail.co Authentication-Results: verifier.port25.com; sender-id=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=appmail.co; s=default; h=Content-Type:To:From:Subject:Message-ID:Date:MIME-Version; bh=GS6uwlT+weKcrrLJ2I+cjBtWPq9nvhwRlNAJebOiQOk=;b=pNw3UQNMoNyZ2Ujv8omHGodKVu/55S8YdBEsA5TbRciga/H7f+5noiKvo60vU6oXYyzVKeozFHDoOEMV6m5UTgkdBefogl+9cUIbt5CSrTWA97D7tGS97JblTDXApbZH; Received: from mail-pb0-f46.google.com ([209.85.160.46]:57831) by app.appmail.co with esmtpa (Exim 4.77) (envelope-from <[email protected]>) id 1SamIF-00055f-Om for [email protected]; Sat, 02 Jun 2012 16:44:51 +0530 Received: by pbbrp8 with SMTP id rp8so4165728pbb.5 for <[email protected]>; Sat, 02 Jun 2012 04:14:51 -0700 (PDT) MIME-Version: 1.0 Received: by 10.68.216.33 with SMTP id on1mr19414885pbc.105.1338635690988; Sat, 02 Jun 2012 04:14:50 -0700 (PDT) Received: by 10.143.66.13 with HTTP; Sat, 2 Jun 2012 04:14:50 -0700 (PDT) Date: Sat, 2 Jun 2012 16:44:50 +0530 Message-ID: <CADnDhbH9aDBk3Ho2-CrG7gwOoD6RNX0sFq4bWL64+kmo=9HjWg@mail.gmail.com> Subject: Test From: shashank sharma <[email protected]> To: [email protected] Content-Type: multipart/alternative; boundary=047d7b2eda75d8544d04c17b6841 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - app.appmail.co X-AntiAbuse: Original Domain - verifier.port25.com X-AntiAbuse: Originator/Caller UID/GID - [47 12] / [47 12] X-AntiAbuse: Sender Address Domain - appmail.co --047d7b2eda75d8544d04c17b6841 Content-Type: text/plain; charset=UTF-8 Hello Senders --047d7b2eda75d8544d04c17b6841 Content-Type: text/html; charset=UTF-8 Hello Senders --047d7b2eda75d8544d04c17b6841-- I also tried to send mail on yahoo , rediff but i get mails in spam. Please help me to sort out this issue

  Read the article

• Connect to internet through DC with 2 network interfaces

  - by Ali Foroughi

  I have a network like this : Client 1 <== Wireless ==> Access Point <== Wire ==> DC <== Wireless ==> ADSL Modem Client 1 : IP : 192.168.1.181 DG : 192.168.1.100 DNS : 192.168.1.100 Access Point : IP : 192.168.1.10 DG : 192.168.1.100 DC : IP : 192.168.1.100 DG : 192.168.1.1 DNS : 127.0.0.1 ADSL Modem : IP : 192.168.1.1 I can ping yahoo.com from client1, but cannot browse the internet. UPDATE1 : my DC has two network interfaces that I bridge together. UPDATE2 : I powered down the DC firewall UPDATE3 : I set a forwarder for my DC to 8.8.8.8 (Google dns)

  Read the article

• How can I selectively increase latency? E.g. throttle games

  - by Arcymag

  Basically, I want networked games to run poorly on a network, but I want everything else to run smoothly. I would also appreciate advice on blocking games in general. As far as I can tell, there's a few ways to completely prevent an internet game from running: Blocking entirely via DNS configuration (e.g. hosts file), or router DNS configuration Blocking entirely via a separate DNS server Blocking the application, by uninstalling or some kind of access control Blocking the application by automatically killing the process every once in a while Blocking the application by corrupting files periodically However, I would like a more subtle way to block a program. Something that either: Increases latency (would this be doable through some kind of QoS like what DD-WRT offers?) Increases latency by using a special routing configuration for specific target IPs Throttle other systems resources, such as memory, IO, or CPU Screw around with keyboard configurations when a game is launched I would like this to work on MacOSX and Windows, but Linux would be great too. FYI I don't have a kid, but I was brainstorming with some friends and parents.

  Read the article

• Problems installing LYNC on non-domain controler

  - by Trikks

  I have two servers in this set up. AD and EX, the domain is called mydomain.net The AD is a Windows 2008 Server (32 bit) with Active Directory installed AD only has it's own ip in the DNS-servers list AD.mydomain.net does resolve correctly in the dns EX is a Windows 2008 R2 that is connected to the mydomain.net-domain EX only DNS server is the ip of the ad.mydomain.net There are no firewalls running between the two servers When trying to install Lync 2010 on the EX server I get the following error "Not available :Failure occurred attempting to check the schema state.Please ensure Active Directory is reachable." I can control the AD from EX, also login to it and do successful checks like netdom query /domain:mydomain.net fsmo ...that resolves correctly I suspect there is something fundamentally wrong with my setup, maybe Lync need a 2k8 R2 ad?

  Read the article

• Specific IP routing for VPN

  - by Roy

  Is there a way that I can prevent an entire subnet from using internal routing. The VPN server is supposed to be a way to access the company's intranet websites for some people, while for others it is supposed to do routing to the outside only and therefore not having access to any internal websites. The VPN server has a DNS on the actual server but not all should be using this DNS. Some of the users should be directly sent out of the server to the internet. Example: 10.0.0.1 is the DNS on the server, gateway for the VPN 10.0.0.2 is a user (A) on the VPN having access to the intranet websites (subnet is 10.0.0.0/25) 10.0.0.192 is a user (B) only needing routing and no access to intranet websites (subnet is 10.0.0.192/26) All traffic of user B should be directly rerouted out of the server. I have tried several iptables but without success.

  Read the article

• Routing a PPTP client and VMware Server instance running on the same box

  - by servermanfail

  I have a Windows 2003 SBS box. It has 2 physical NIC's: WAN and LAN. The WAN is a public IP. The LAN is a simple 192.168.2.x subnet with Microsoft DHCP Server. Microsoft Routing and Remote Access Service is used to provide NAT to LAN. The box also runs VMware Server with a virtual machine running Windows XP. I want people to be able to VPN into the box, and connect to these virtual machines on the MSRDP port. I can VPN (PPTP) into the 2003 SBS box fine, as well as ping other machines on the LAN. I can ping the VM from a physical workstation on the LAN and vice-versa. I can ping the VPN client from the a physical workstation on the LAN and vice-versa. I can ping the VPN client from the Server console and vice-versa. I can ping the VM client from the Server console and vice-versa. But I cannot ping the VPN client from the VM and vice-versa. I was hoping to set up 2 or 3 Windows XP virtual machines on our only server, so that a couple of people can remote in to work without having to leave a physical machine on in the office. You could this attempted set up a "poor mans terminal server". On the 2003 SBS Server:- C:\Documents and Settings\Administrator>route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 50 56 c0 00 08 ...... VMware Virtual Ethernet Adapter for VMnet8 0x3 ...00 50 56 c0 00 01 ...... VMware Virtual Ethernet Adapter for VMnet1 0x10004 ...00 53 45 00 00 00 ...... WAN (PPP/SLIP) Interface 0x10005 ...00 11 43 d4 69 13 ...... Broadcom NetXtreme Gigabit Ethernet 0x10006 ...00 11 43 d4 69 14 ...... Broadcom NetXtreme Gigabit Ethernet #2 =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 81.123.144.22 81.123.144.21 1 81.123.144.20 255.255.255.252 81.123.144.21 81.123.144.21 1 81.123.144.21 255.255.255.255 127.0.0.1 127.0.0.1 1 81.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 86.135.78.235 255.255.255.255 81.123.144.22 81.123.144.21 1 109.152.62.236 255.255.255.255 81.123.144.22 81.123.144.21 1 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.2.0 255.255.255.0 192.168.2.3 192.168.2.3 1 192.168.2.3 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.26 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.28 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.32 255.255.255.255 127.0.0.1 127.0.0.1 50 192.168.2.50 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.255 255.255.255.255 192.168.2.3 192.168.2.3 1 192.168.10.0 255.255.255.0 192.168.10.1 192.168.10.1 20 192.168.10.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.10.255 255.255.255.255 192.168.10.1 192.168.10.1 20 192.168.96.0 255.255.255.0 192.168.96.1 192.168.96.1 20 192.168.96.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.96.255 255.255.255.255 192.168.96.1 192.168.96.1 20 224.0.0.0 240.0.0.0 81.123.144.21 81.123.144.21 1 224.0.0.0 240.0.0.0 192.168.2.3 192.168.2.3 1 224.0.0.0 240.0.0.0 192.168.10.1 192.168.10.1 20 224.0.0.0 240.0.0.0 192.168.96.1 192.168.96.1 20 255.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 255.255.255.255 255.255.255.255 192.168.2.3 192.168.2.3 1 255.255.255.255 255.255.255.255 192.168.10.1 192.168.10.1 1 255.255.255.255 255.255.255.255 192.168.96.1 192.168.96.1 1 Default Gateway: 81.123.144.22 =========================================================================== Persistent Routes: None C:\Documents and Settings\Administrator>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : 2003server Primary Dns Suffix . . . . . . . : mycompany.local Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : Yes WINS Proxy Enabled. . . . . . . . : Yes DNS Suffix Search List. . . . . . : mycompany.local gateway.2wire.net Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.10.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.96.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : PPP adapter RAS Server (Dial In) Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface Physical Address. . . . . . . . . : 00-53-45-00-00-00 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.32 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-11-43-D4-69-13 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 IP Address. . . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.2.3 Primary WINS Server . . . . . . . : 192.168.2.3 Ethernet adapter WAN: Connection-specific DNS Suffix . : gateway.2wire.net Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2 Physical Address. . . . . . . . . : 00-11-43-D4-69-14 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 81.123.144.21 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : 81.123.144.22 DHCP Server . . . . . . . . . . . : 10.0.0.1 DNS Servers . . . . . . . . . . . : 10.0.0.1 Primary WINS Server . . . . . . . : 192.168.2.3 NetBIOS over Tcpip. . . . . . . . : Disabled Lease Obtained. . . . . . . . . . : 25 February 2011 22:56:59 Lease Expires . . . . . . . . . . : 25 February 2011 23:06:59 C:\Documents and Settings\Administrator>ping 192.168.2.11 Pinging 192.168.2.11 with 32 bytes of data: Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128

  Read the article

• Send all traffic over VPN connection not working Windows VPN host

  - by Adam Schiavone

  I am trying to get a mac (10.8) to connect to thru vpn to a server running Windows Server 2008 R2 pass all requests from the mac to the server. The VPN is setup and I can connect and access the server thru a web browser, but for all other sites, the DNS lookup fails. I have tried adding a DNS server to the VPN Host. ex. Lets say the the VPN server also hosts a website example.com. I connect to the VPN with my mac and point a browser to example.com and everything works fine. but when I point the browser to google.com it just sits there and will eventually come back with a DNS lookup failed message. HOWEVER: I tried running the command dig @myServersIpHere www.google.com. on the mac and it comes back with correct IP addresses. I really dont know what to do from here. How can I route all requests from my mac, thru my windows server via VPN?

  Read the article

• Run script when POST data is sent to Apache

  - by Nathan Adams

  Among my several years of running servers there seems to be a pattern with most spam activity. My question/idea is that is there a way to tell Apache to run a script when POST data is detected? What I would want to do is perform a reverse DNS lookup on the client's IP address, and then perform a DNS lookup on the hostname in the PTR record. Afterwards, perform some checks, excuse the pseudo-code: if PTR does not exist: deny POST request if IP of PTR hostname = client's IP Allow POST request else deny POST request Though I don't care about GET requests, even though they can be just as malicious, this idea is targeted towards spam comments which use POST data to send the comment data to the web server. In order to make sure there isn't much of a time delay, I would run my own recursive DNS server. Please do note, this isn't meant to be a sliver bullet to spam, but it should decrease the volume. Possible or impossible?

  Read the article

• bind udp problem

  - by mascix

  I am using bind 9.6.1 and about 2 days ago I realized that there is a bug at bind for windows platform. when server gets "UDP client handler shutting down due to fatal receive error: host unreachable" error. it stays alive but no response for after dns queries. then I need to restart it manually to make it responsive(I put a task for this issue from windows). I cant use microsoft windows dns server because I am using windows 2008 server web edition which does not include that. so my question is what are the other solutions you use for dns server in windows ?

  Read the article

• belkin wireless router connection drops for ~60sec every ~15 mins

  - by j j

  Hi, I have a belkin wireless-g router, model F5D7230-4. about every 10-15 minutes, for about 1-1.5 mins I won't be able to browse any web sites. during this period, I usually get replys from "ping google.com". maybe 4/5 times I'll get a reply, 1/5 times i don't. I have changed the router DNS entries from "get DNS server from ISP" to 8.8.8.8, google's DNS and that hasn't fixed the situation. This happens on several computers, running windows7, xp, ubuntu, and a mac, so it is definitely NOT an issue with a computer configuration. any ideas?

  Read the article

• Upgrading Active Directory from 2000 to 2008

  - by Doug

  Our config is currently: 1 Windows 2000 domain controller running ISA2000, dhcp, dns 1 Windows 2003 domain controller as main file server, prob cert server as well, dhcp, dns 1 Windows 2008/Exchange2010 domain controller as Exchange server, DHCP,DNS Currently getting FRS errors on files server journalwrap error Currently getting FRS errors on othe DC's can't replicate from above Exchange DC holds Schema, rid,pdc, and infastructure roles File Server holds Domain namaing operation master role WOW, I didn't set this up, just inherited it. Am I right to assume that fixing the FRS errors is #1, what do I need to do for that? set enable journalwrap auto restore in registry? Demote W2000 domain controller, should that have any implications for ISA? We have Forefront to be deployed but that's another day Transfer Domain Nameing Role to Exchange server (I know or think having an Exchange server as DC isn't best practive) We will be getting another server W2008 to replace current file server and I thought it could takeover all roles once deployed Demote W2k3 file server and then raise functional domain level to 2008 Am I missing anything other that the sense to walk away? Thanks

  Read the article

• Sendmail problem

  - by trobrock

  I am trying to get my server to be able to send email from PHP. Currently it is using send mail, but whenever I try to send mail to a gmail address I get this sort of response: --o54Mqd5s008981.1275691959/ServerName Content-Type: message/delivery-status Reporting-MTA: dns; ServerName Received-From-MTA: DNS; localhost Arrival-Date: Fri, 4 Jun 2010 22:52:38 GMT Final-Recipient: RFC822; [email protected] Action: failed Status: 5.7.1 Remote-MTA: DNS; gmail-smtp-in.l.google.com Diagnostic-Code: SMTP; 550-5.7.1 [xxx.xxx.xxx.xxx] The IP you're using to send mail is not authorized Last-Attempt-Date: Fri, 4 Jun 2010 22:52:39 GMT How can I set this up to relay through a google account that I own? Is sendmail the best thing to use, or should I switch to Postfix or something? This is on an Ubuntu Server 9.10

  Read the article

• Help with OpenVPN setup on Windows Server 2003

  - by Bill Johnson

  Hi all, Just wondering if someone can assist me further with the set-up of OpenVPN on my Windows Server 2003. I have configured Win Server as per the following guide: http://tinyurl.com/kxusv and I'm now at the stage of Creating the config files. I have a few questions that I need some assistance with. My server IP is 192.168.1.10 and my routers IP address is 192.168.1.1 (the router is a Netgear DGN2000). I have edited the server.ovpn file as per the following: push "dhcp-option DNS X.X.X.X" # Replace the Xs with the IP address of the DNS for your home network (usually your ISP's DNS) push "dhcp-option DNS X.X.X.X" # A second DNS server if you have one to include my ISP DNS and I have not edited anything else. Now my issue is with the client1.opvpn file as per the below: client dev tap #dev-node MyTAP #If you renamed your TAP interface or have more than one TAP interface then remove the # at the beginning and change "MyTAP" to its name proto udp remote YOURHOST.dyndns.org 1194 #You will need to enter you dyndns account or static IP address here. The number following it is the port you set in the server's config route 192.168.1.0 255.255.255.0 vpn_gateway 3 #This it the IP address scheme and subnet of your normal network your server is on. Your router would usually be 192.168.1.1 resolv-retry infinite nobind persist-key persist-tun ca "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\ca.crt" cert "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\client1.crt" # Change the next two lines to match the files in the keys directory. This should be be different for each client. key "C:\\Program Files\\OpenVPN\\easy-rsa\\keys\\client1.key" # This file should be kept secret ns-cert-type server cipher BF-CBC # Blowfish (default) encrytion comp-lzo verb 1 To me it looks like I will need to amend the following: remote YOURHOST.dyndns.org 1194 #You will need to enter you dyndns account or static IP address here. The number following it is the port you set in the server's config route 192.168.1.0 255.255.255.0 vpn_gateway 3 #This it the IP address scheme and subnet of your normal network your server is on. Your router would usually be 192.168.1.1 So, should the first line be the static IP of the machine that I'm applying this to? The IP address of the server (192.168.1.10) or something else? I'm also stuck on the second part 'route 192.168.1.0 255.255.255.0 vpn_gateway 3' Should this be the router IP which is 192.168.1.1 and the subnet is 255.255.255.0 and that is all I need to alter? The final part that I'm stuggling with is Configuring the router. Basically I have a Netgear DGN2000 and as it mentions that the router should be configured to port forward port 1194 to the server’s IP address of 192.168.1.150 all I have been able to do is in 'Firewall Rules' and on 'Inbound Services', set the Service to 'Any(ALL) and Send to LAN Server point to 1923.168.1.150. I'm not sure if this is correct? It is the following stage of the help guide that I'm struggling with and really need some help with: You need to make sure the port you configured OpenVPN to listen on is forwarded on the router to the IP address of your server. On the WRT54G, port forwarding is configured in the “Applications & Gaming” section. Enter 1194 for the port, UDP for the protocol, and 192.168.1.150 for the IP address. Make sure the entry is enabled and then save the setting. Next, you need to add an entry to the router’s Routing Table. This will enable the router to properly route requests from the clients to the TAP interface of the server. On the WRT54G you would go to the “Setup” page and then the “Advanced Routing” section. Enter the follwing info to make the entry: Enter Route Name: openVPN Destination LAN IP: 192.168.10.0 Subnet Mask: 255.255.255.252 Default Gateway: 192.168.1.150 Interface: LAN & Wireless Once the info has been typed in make sure you save the setting. Can anyone possibly guide me through setting this part up with my Netgear router. I see that once I have these 2 parts complete I'm there so I would really appreciate someone walking me through what is required in completing this. Much appreciated.

  Read the article

• Active Directory: trouble adding new DC

  - by ethrbunny

  I have a domain with 3 DCs. One is starting to fail so I brought up a new one. All are running Win 2003. Problem: there appear to be replication issues between the 4 machines but I can't figure out what's causing this. All are registered with the DNS as identically as I can make them. How do I know there is a problem? Nagios is telling me that the other 3 DCs are having KCCEvent errors and the new machine is reporting "failed connectivity" errors. Doing dcdiag on the new machine reports: the host could not be resolved to an IP address. This seems crazy as I log into it using the DNS name. I can ping it from the other three machines using this DNS name as well. repadmin /showreps from the new machine says its seeing the other 3 machines. Doing the same from one of the older machines doesn't show the new machine. I've tried netdiag /repair numerous times. No luck. There are no firewalls running on any of the machines. If I look at Domain info via MMC (on the new machine) it appears that all the information is current. Users, computers, DCs.. its all there. Im puzzled as to what step(s) I've missed in adding this new machine. Suggestions? EDIT: dcdiag from non-working: C:\Documents and Settings\Administrator.BME>dcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\YELLOW Starting test: Connectivity The host 312ce6ea-7909-4e15-aff6-45c3d1d9a0d9._msdcs.server.edu could not be resolved to an IP address. Check the DNS server, DHCP, server name, etc Although the Guid DNS name (312ce6ea-7909-4e15-aff6-45c3d1d9a0d9._msdcs.server.edu) couldn't be resolved, the server name (yellow.server.edu) resolved to the IP address (10.127.24.79) and was pingable. Check that the IP address is registered correctly with the DNS server. ......................... YELLOW failed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\YELLOW Skipping all tests, because server YELLOW is not responding to directory service requests Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : bme Starting test: CrossRefValidation ......................... bme passed test CrossRefValidation Starting test: CheckSDRefDom ......................... bme passed test CheckSDRefDom Running enterprise tests on : server.edu Starting test: Intersite ......................... server.edu passed test Intersite Starting test: FsmoCheck ......................... server.edu passed test FsmoCheck dcdiag from working: P:\>dcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\AD1 Starting test: Connectivity ......................... AD1 passed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\AD1 Starting test: Replications ......................... AD1 passed test Replications Starting test: NCSecDesc ......................... AD1 passed test NCSecDesc Starting test: NetLogons ......................... AD1 passed test NetLogons Starting test: Advertising ......................... AD1 passed test Advertising Starting test: KnowsOfRoleHolders ......................... AD1 passed test KnowsOfRoleHolders Starting test: RidManager ......................... AD1 passed test RidManager Starting test: MachineAccount ......................... AD1 passed test MachineAccount Starting test: Services ......................... AD1 passed test Services Starting test: ObjectsReplicated ......................... AD1 passed test ObjectsReplicated Starting test: frssysvol ......................... AD1 passed test frssysvol Starting test: frsevent ......................... AD1 passed test frsevent Starting test: kccevent ......................... AD1 passed test kccevent Starting test: systemlog ......................... AD1 passed test systemlog Starting test: VerifyReferences ......................... AD1 passed test VerifyReferences Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : bme Starting test: CrossRefValidation ......................... bme passed test CrossRefValidation Starting test: CheckSDRefDom ......................... bme passed test CheckSDRefDom Running enterprise tests on : server.edu Starting test: Intersite ......................... server.edu passed test Intersite Starting test: FsmoCheck ......................... server.edu passed test FsmoCheck P:\>

  Read the article

• First request too slow even if I have a load balancer in the back

  - by adrian7

  I have an Apache 2 on Centos + bind with a wordpress website on it (e.g example.com). I have also set up, on another server in a different contry a load balancer (varnish:80 + nginx 127.0.0.1:8080) for it - which task is to server all static content under /wp-content/. Using Simple DNS editor I added an A entry to cdn.example.com pointing to the server's IP. So no extra work from a 2nd dns server. Then using htaccess I redirect all requests to jpg|gif|css|js files to cdn.example.com. That works and all files are saved on the "cdn" server and served right away. My problem is that for the first time I enter on example.com (e.g after restarting the computer or closing the browser) the load time is 1 up to 3 seconds, while any subsequent page loads take only 300 to 600 miliseconds. I know it might be a DNS issue, but I have done a cache check on several websites and cdn.example.com indicates the right IP. Do you have any ideas where I should dig to solve this first-time slowness?

  Read the article

• Hp Procurve Switch : port filtered

  - by user117140

  My HP Procurve switch is blocking port 22 and I dont know how to unblock it.Please let me know From the server, see port 22 is blocked [root@server ~]#nmap -p22,80,443 10.247.172.70 Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2012-04-16 14:12 IST mass_dns: warning: Unable to determine any DNS servers. Reverse DNS is disabled. Try using --system-dns or specify valid servers with --dns_servers Interesting ports on 10.247.172.70: PORT STATE SERVICE 22/tcp filtered ssh ------------------> see 80/tcp filtered http 443/tcp filtered https This is blocked on cisco switch but I dont have any clue how this is done. I know that vlan is configured on switch. vlan 54 ip ospf 10.247.172.65 area 0.0.0.10 vrrp vrid 54 owner virtual-ip-address 10.247.172.65 255.255.255.192 priority 255 enable exit exit Please let me know how to unblock ssh port 22 access on this switch?

  Read the article

• Accessing C$ over LAN on Win2008R2 - cannot by hostname but can by IP and FQDN

  - by Idgoo

  Having an issue with one of our Win2k8 R2 file servers. Trying to access C$ or the Admin share is giving us an error (see error details that the bottom), however we are able to connect using the server's IP and FQDN. can access \\172.16.x.x\c$ with domain cred can access \\server.domain.local\c$ with domain creds cannot access \\servername\c$ with same domain creds Server pings fine with Hostname, IP, FQDN, the Primary DNS suffix is also correct. DNS, PTR and Wins records are all correct for the Server I have checked that I am not trying to connect with cached credentials in the Windows vault, the server is also appending primary and connection specific DNS suffixes to the hostname. Any ideas what might be causing this issue? Error Details: c$ is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions

  Read the article

• Eliminate single point of failure for webservers?

  - by George Bailey

  I know in DNS, that each of the DNS servers will be tried to see if they will respond I know in email that in the event of a failure it will go to the next one in the list or it will hold the mail for a period of time As far as I know,, in webservers,, the browser will get one of the webserver IP addresses and try it and if it fails it will give up. Is this correct? If so,, then the only way to direct traffic away from a failed IP address would be with the DNS servers.. and even that would not update immediately?

  Read the article

• Is it possible to cause email to my domain to be handled by gmail?

  - by pitosalas

  [This is a very narrow question, and I don't think it is covered in similar sounding questions] I want to configure my server's DNS so that when someone sends email to [email protected] it is actually deliver it to [email protected] Note: My question is whether this is possible to do ONLY with DNS not with myserver.com's own sendmail. I think the answer is "NO" it is not possible, because when I add an MX record to DNS the email that was delivered to gmail's SMPT server would be TO: [email protected] and it would not know that account. (But I hasten to add that I am just vaguely starting to grok how this all works.)

  Read the article

• Setting Up DHCP Server as Failover

  - by Jason Buhagiar

  I have 2 Domain Controllers running at my company; DC1 has the following roles; ADDS DNS DHCP Scope - 192.168.2.100 - 192.168.2.240 DC2 has the following roles; ADDS - Replicated DNS - Secondary DNS I also have 2 PFSense Gateways both have a different ISP Connection, DHCP Relay is not enabled on any of the machines. Can anyone suggest a way for me to install DHCP Server as FAilover on DC2 please, should I use split scope etc... Help is much appreciated :) Thanks.

  Read the article

• Intel Corporation Ethernet Connection does not start properly

  - by Oscar Alejos

  I'm experiencing some problems when trying to connect my PC to the router through a switch. When the PC is directly connected to the router, everything works fine, Ubuntu (14.04) starts normally, and the Internet connection runs inmediately. The Ethernet controller is the Intel Corporation Ethernet Connection, as lspci returns: $ lspci | grep Eth 00:19.0 Ethernet controller: Intel Corporation Ethernet Connection I217-V (rev 04) However, when I try to connect through the switch what I get is the following. dmesg returns: $ dmesg | grep eth [ 1.035585] e1000e 0000:00:19.0 eth0: registered PHC clock [ 1.035587] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:22:4d:a7:be:5d [ 1.035589] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection [ 1.035625] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF [ 1.357838] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.165413] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.165574] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 2.641287] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.715086] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx [ 16.715090] e1000e 0000:00:19.0 eth0: 10/100 speed: disabling TSO [ 16.715117] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready It looks like eth0 is properly working. Actually, nm-tool returns: $ nm-tool - Device: eth0 [Conexión cableada] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: 00:22:4D:A7:BE:5D Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.30 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 80.58.61.250 DNS: 80.58.61.254 DNS: 192.168.1.1 However, ping returns: $ ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. From 192.168.1.30 icmp_seq=1 Destination Host Unreachable From 192.168.1.30 icmp_seq=2 Destination Host Unreachable From 192.168.1.30 icmp_seq=3 Destination Host Unreachable The connection is restored by restarting it: # ifconfig eth0 down # ifconfig eth0 up From this point on, everything runs smoothly, as if the PC were directly connected to the router. It seems to be an issue related to the integrated LAN adaptor and the Ethernet controller, since my laptop connects without any problem. My desktop board is an Intel DB85FL. I'd be grateful if anyone could give some ideas on how to solve this issue. Thank you in advance.

  Read the article

• Step by Step Install of MAAS and JUJU

  - by John S

  I am working on understanding the pieces that I am missing in being able to deploy Juju across the other MAAS nodes. I don't know If I have a step out of place, or missing a few. The server owns the router which handles the DHCP and DNS. Any assistance is greatly appreciated. When I am at the end I will either get a 409 error, or arbitrary pick tools 1.16.0 error. It is worth mentioning that local, and aws works fine. Hopefully with all of these steps spelled out it will help someone else along the way too. Steps Setting Up MAAS and JUJU - 12.04 LTS Clean install SSH only from the package selection during install sudo apt-get install software-properties-common sudo apt-get install python-software-properties sudo add-apt-repository ppa:maas-maintainers/stable sudo add-apt-repository ppa:juju/stable sudo apt-get update sudo apt-get dist-upgrade sudo reboot sudo apt-get install maas maas-dns maas-dhcp sudo ufw disable sudo reboot - edit /etc/dhcp/dhcpd.conf authoritive subnet 10.0.0.0 netmask 255.255.255.0 { next-server 10.0.0.2; filename "pxelinux.0"; } sudo maas createsuperuser sudo maas-import-pxe-files Login to MAAS http://10.x.x.x/MAAS cluster controller configuration for eth0 manage dhcp and dns IP 10.0.0.2 subnet 255.255.255.0 broadcast 10.0.0.0 routerip 10.0.0.1 ip low 10.0.0.5 ip high 10.0.0.180 Commissioning default and distro is set at 12.04 default domain is at local sudo maas-cli login maas http://10.x.x.x/MAAS/api/1.0 api-key ssh-keygen -t rsa -b 2048 - enter - no password - cat id_rsa.pub and enter key into MAAS ssh sudo maas-cli maas nodes accept-all (interestingly enough I only get back [] when executing this ) PXE one machine, accept and commision, start and deploy. sudo apt-get install juju-core juju-local MAAS config: maas: type: maas maas-server: '://10.x.x.x:80/MAAS' maas-oauth: 'MAAS_API_KEY' admin-secret: 'nothing' default-series: 'precise' juju switch maas sudo juju bootstrap --show-log

  Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >