Search Results

Search found 4453 results on 179 pages for 'kernel parametes'.

Page 93/179 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

  • QoS basics on a Cisco ASA

    - by qbn
    Could someone briefly explain how to use QoS on Cisco ASA 5505? I have the basics of policing down, but what about shaping and priorities? Basically what I'm trying to do is carve out some bandwidth for my VPN subnets (in an object-group called priority-traffic). I've seen this Cisco QoS document, however configuring shaping and priority-queue don't seem to have any effects in my test. A full download of the linux kernel from kernel.org will boost a ping to a server via VPN sky high. Policing has been successful in passing this test, although it doesn't seem as efficient (I cap non-vpn traffic at 3 of my 4.5 megabits of bandwidth). Am I misunderstanding the results of the test? I think there is some simple concept I'm not grasping here. EDIT: Here is my config thus far (I have 4.5 megabits of bandwidth): access-list priority-traffic extended permit ip object-group priority-traffic any access-list priority-traffic extended permit ip any object-group priority-traffic access-list priority-traffic extended permit icmp object-group priority-traffic any access-list priority-traffic extended permit icmp any object-group priority-traffic access-list non-priority-traffic extended deny ip object-group priority-traffic any access-list non-priority-traffic extended deny ip any object-group priority-traffic access-list non-priority-traffic extended permit ip any any priority-queue outside queue-limit 440 class-map non-priority-traffic match access-list non-priority-traffic class-map priority-traffic match access-list priority-traffic class-map inspection_default match default-inspection-traffic policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp policy-map outbound-qos-policy class non-priority-traffic police input 2500000 police output 2500000 class priority-traffic priority service-policy global_policy global service-policy outbound-qos-policy interface outside

    Read the article

  • CentOS 5.5 ext4 conversion problem - ext4 partition is recognized as ext3

    - by FractalizeR
    Hello. I had 5.4 machine. Upgraded to 5.5 today via yum upgrade. All went fine. Rebooted. Wanted to convert root partition to ext4 (I have three partitions: /boot, / and swap). All of them on software RAID 1 (root is /dev/md2). I did the following for converting yum install e4fsprogs tune2fs -O extents,uninit_bg,dir_index /dev/md2 nano /etc/fstab # I indicated here that my /dev/md2 is of ext4 uname -a mkinitrd -f /boot/initrd-2.6.18-194.3.1.el5.img 2.6.18-194.3.1.el5 Rebooted. I expected fsck to start automatically as said on some site. But it did not. Threw some error (don't remember exactly which). Ok, I booted linux rescue and executed fsck: fsck -t ext4 -fy /dev/md2 Partition went fine. But still when I boot main system, it says in log: "ext3-fs:" then something about not being able to mount ext3 partition due to unknown extended attributed (200). I booted linux rescue again. It loads fine and correctly determines all my machine partitions both ext3 (boot) and ext4 (/) under /mnt/sysimage just fine. I retried mkinitrd thing again watching it's output and ensured ext4 module is included into the system. I also edited menu.lst grub file to include rootfstype=ext4 kernel parameter. Bad luck. I still have message from ext3-fs about not being able to mount filesystem because of attributes and kernel panic immediately after. I checked /etc/fstab - it's fine and saying that root is of ext4. What did I do wrong? This machine is empty so I can just reformat it with 5.5 and recreate partitions to be originally ext4. But... I just want to know what did I do wrong.

    Read the article

  • Unable to connect Xend with virt-manager

    - by Majid Azimi
    I have installed debian 6.0.1a. I have install all XEN stuff. including xen kernel, libvirtd, ... but when i want to connect xend, virt-manager shows me this: Verify that: A Xen host kernel was booted The Xen service has been started details: Unable to open connection to hypervisor URI 'xen:///': unable to connect to '/var/run/libvirt/libvirt-sock', libvirtd may need to be started: Permission denied Traceback (most recent call last): File "/usr/share/virt-manager/virtManager/connection.py", line 971, in _try_open None], flags) File "/usr/lib/python2.6/dist-packages/libvirt.py", line 111, in openAuth if ret is None:raise libvirtError('virConnectOpenAuth() failed') libvirtError: unable to connect to '/var/run/libvirt/libvirt-sock', libvirtd may need to be started: Permission denied here is uname output: Linux debian 2.6.32-5-xen-amd64 #1 SMP Tue Mar 8 00:01:30 UTC 2011 x86_64 GNU/Linux and also xend and libvirtd is runnig: root@debian:/home/mazimi# /etc/init.d/libvirt-bin status Checking status of libvirt management daemon: libvirtd running. root@debian:/home/mazimi# /etc/init.d/xend start Starting Xen daemons: xenstored xenconsoled xend. permissions for livbirt-sock: root@debian:/home/mazimi# ls -alih /var/run/libvirt/ total 12K 671017 drwxr-xr-x 3 root root 4.0K Apr 15 13:54 . 654083 drwxr-xr-x 18 root root 4.0K Apr 15 13:54 .. 670901 srwxrwx--- 1 root libvirt 0 Apr 15 13:54 libvirt-sock 670928 srwxrwxrwx 1 root libvirt 0 Apr 15 13:54 libvirt-sock-ro 670870 drwxr-xr-x 2 root root 4.0K Apr 15 02:34 qemu and also we have group named libvirt in /etc/group When running libvirtd with verbose mode it behaves kind of stange: root@debian:/var/log/libvirt# /usr/sbin/libvirtd --verbose 17:26:55.841: warning : qemudStartup:1832 : Unable to create cgroup for driver: No such device or address 17:26:56.128: warning : lxcStartup:1900 : Unable to create cgroup for driver: No such device or address and waits infinitely.

    Read the article

  • ipvsadm lists a few hosts by IP only, rest by name

    - by dmourati
    We use keepalived to manage our Linux Virtual Server (LVS) load balancer. The LVS VIPs are setup to use a FWMARK as configured in iptables. virtual_server fwmark 300000 { delay_loop 10 lb_algo wrr lb_kind NAT persistence_timeout 180 protocol TCP real_server 10.10.35.31 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.31" misc_timeout 30 } } real_server 10.10.35.32 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.32" misc_timeout 30 } } real_server 10.10.35.33 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.33" misc_timeout 30 } } real_server 10.10.35.34 { weight 24 MISC_CHECK { misc_path "/usr/local/sbin/check_php_wrapper.sh 10.10.35.34" misc_timeout 30 } } } http://www.austintek.com/LVS/LVS-HOWTO/HOWTO/LVS-HOWTO.fwmark.html [root@lb1 ~]# iptables -L -n -v -t mangle Chain PREROUTING (policy ACCEPT 182G packets, 114T bytes) 190M 167G MARK tcp -- * * 0.0.0.0/0 w1.x1.y1.4 multiport dports 80,443 MARK set 0x493e0 62M 58G MARK tcp -- * * 0.0.0.0/0 w1.x1.y2.4 multiport dports 80,443 MARK set 0x493e0 [root@lb1 ~]# ipvsadm -L IP Virtual Server version 1.2.1 (size=4096) Prot LocalAddress:Port Scheduler Flags -> RemoteAddress:Port Forward Weight ActiveConn InActConn FWM 300000 wrr persistent 180 -> 10.10.35.31:0 Masq 24 1 0 -> dis2.domain.com:0 Masq 24 3 231 -> 10.10.35.33:0 Masq 24 0 208 -> 10.10.35.34:0 Masq 24 0 0 At the time the realservers were setup, there was a misconfigured dns for some hosts in the 10.10.35.0/24 network. Thereafter, we fixed the DNS. However, the hosts continue to show up as only their IP numbers (10.10.35.31,10.10.35.33,10.10.35.34) above. [root@lb1 ~]# host 10.10.35.31 31.35.10.10.in-addr.arpa domain name pointer dis1.domain.com. OS is CentOS 6.3. Ipvsadm is ipvsadm-1.25-10.el6.x86_64. kernel is kernel-2.6.32-71.el6.x86_64. Keepalived is keepalived-1.2.7-1.el6.x86_64. How can we get ipvsadm -L to list all realservers by their proper hostnames?

    Read the article

  • Problem setting command-line console resolution. vbeinfo in grub2 does not report all resolutions

    - by Kent
    I have a Asus EEE PC 1005P which I installed a Command-line system on using the Alternate Installer CD of Ubuntu Lucid Lynx. Altough I think this is a general linux and grub2 question. I do not have (or want) the X Window System installed. I want to change my console screen resolution (not inside X) to 1024x600. But it isn't reported when I use vbeinfo inside grub: grub> vbeinfo VBE info: version: 3.0 OEM software rev: 1.0 total memory: 8128 KiB List of compatible video modes: Legend: P=Packed pixel, D=Direct color, mask/pos=R/G/B/reserved 0x112: 640 x 480 x 32 Direct, mask: 8/8/8/8 pos: 16/8/0/24 0x114: 800 x 600 x 16 Direct, mask: 5/6/5/0 pos: 11/5/0/0 0x115: 800 x 600 x 32 Direct, mask: 8/8/8/8 pos: 16/8/0/24 0x101: 640 x 480 x 8 Packed 0x103: 800 x 600 x 8 Packed 0x111: 640 x 480 x 16 Direct, mask: 5/6/5/0 pos: 11/5/0/0 Configured VBE mode (vbe_mode) = ox101 grub> Relevant parts of sudo lspci -v: ... ... 00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller Subsystem: ASUSTeK Computer Inc. Device 83ac Flags: bus master, fast devsel, latency 0, IRQ 28 ... Kernel driver in use: i915 Kernel modules: i915 00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller Subsystem: ASUSTeK Computer Inc. Device 83ac Flags: bus master, fast devsel, latency 0, IRQ 28 ... ... ... Any ideas on how I can set the console resultion like I want it?

    Read the article

  • Disabling CPU management

    - by Tiffany Walker
    If I add the following processor.max_cstate=0 to the kernel command line for boot up, does that disable all CPU power management and throttling? I also found: http://www.experts-exchange.com/OS/Linux/Administration/A_3492-Avoiding-CPU-speed-scaling-in-modern-Linux-distributions-Running-CPU-at-full-speed-Tips.html The link talks of Change CPU governor from 'ondemand' to 'performance' for all CPUs/cores and disabling kondemand from kernel. Server is for web hosting UPDATES: 2.6.32-379.1.1.lve1.1.7.6.el6.x86_64 #1 SMP Sat Aug 4 09:56:37 EDT 2012 x86_64 x86_64 x86_64 GNU/Linux . # dmidecode 2.11 SMBIOS 2.6 present. 74 structures occupying 2878 bytes. Table at 0x0009F000. Handle 0x0000, DMI type 0, 24 bytes BIOS Information Vendor: American Megatrends Inc. Version: 1.0c Release Date: 05/27/2010 Address: 0xF0000 Runtime Size: 64 kB ROM Size: 4096 kB Characteristics: ISA is supported PCI is supported PNP is supported BIOS is upgradeable BIOS shadowing is allowed ESCD support is available Boot from CD is supported Selectable boot is supported BIOS ROM is socketed EDD is supported 5.25"/1.2 MB floppy services are supported (int 13h) 3.5"/720 kB floppy services are supported (int 13h) 3.5"/2.88 MB floppy services are supported (int 13h) Print screen service is supported (int 5h) 8042 keyboard services are supported (int 9h) Serial services are supported (int 14h) Printer services are supported (int 17h) CGA/mono video services are supported (int 10h) ACPI is supported USB legacy is supported LS-120 boot is supported ATAPI Zip drive boot is supported BIOS boot specification is supported Targeted content distribution is supported BIOS Revision: 8.16 Handle 0x0001, DMI type 1, 27 bytes System Information Manufacturer: Supermicro Product Name: X8SIE Version: 0123456789 Serial Number: 0123456789 UUID: 49434D53-0200-9033-2500-33902500D52C Wake-up Type: Power Switch SKU Number: To Be Filled By O.E.M. Family: To Be Filled By O.E.M. Handle 0x0002, DMI type 2, 15 bytes Base Board Information Manufacturer: Supermicro Product Name: X8SIE Version: 0123456789 Serial Number: VM11S61561 Asset Tag: To Be Filled By O.E.M. Features: Board is a hosting board Board is replaceable Location In Chassis: To Be Filled By O.E.M. Chassis Handle: 0x0003 Type: Motherboard Contained Object Handles: 0 Handle 0x0003, DMI type 3, 21 bytes Chassis Information Manufacturer: Supermicro Type: Sealed-case PC Lock: Not Present Version: 0123456789 Serial Number: 0123456789 Asset Tag: To Be Filled By O.E.M. Boot-up State: Safe Power Supply State: Safe Thermal State: Safe Security Status: None OEM Information: 0x00000000 Height: Unspecified Number Of Power Cords: 1 Contained Elements: 0

    Read the article

  • NFS4 permission denied when userid does not match (even though idmap is working)

    - by SystemParadox
    I have NFS4 setup with idmapd working correctly. ls -l from the client shows the correct user names, even though the user ids differ between the machines. However, when the user ids do not match, I get 'permission denied' errors trying access files, even though ls -l shows the correct username. When the user ids do happen to match by coincidence, everything works fine. sudo sysctl -w sunrpc.nfsd_debug=1023 gives the following output in the server syslog for the failed file access: nfsd_dispatch: vers 4 proc 1 nfsv4 compound op #1/3: 22 (OP_PUTFH) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsv4 compound op ffff88003d0f5078 opcnt 3 #1: 22: status 0 nfsv4 compound op #2/3: 3 (OP_ACCESS) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking nfsv4 compound op ffff88003d0f5078 opcnt 3 #2: 3: status 0 nfsv4 compound op #3/3: 9 (OP_GETATTR) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking nfsv4 compound op ffff88003d0f5078 opcnt 3 #3: 9: status 0 nfsv4 compound returned 0 nfsd_dispatch: vers 4 proc 1 nfsv4 compound op #1/7: 22 (OP_PUTFH) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsv4 compound op ffff88003d0f5078 opcnt 7 #1: 22: status 0 nfsv4 compound op #2/7: 32 (OP_SAVEFH) nfsv4 compound op ffff88003d0f5078 opcnt 7 #2: 32: status 0 nfsv4 compound op #3/7: 18 (OP_OPEN) NFSD: nfsd4_open filename dom_file op_stateowner (null) renewing client (clientid 4f96587d/0000000e) nfsd: nfsd_lookup(fh 28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba, dom_file) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking nfsd: fh_lock(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) locked = 0 nfsd: fh_compose(exp 08:01/22806529 srv/dom_file, ino=22809724) nfsd: fh_verify(36: 01070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking fh_verify: srv/dom_file permission failure, acc=804, error=13 nfsv4 compound op ffff88003d0f5078 opcnt 7 #3: 18: status 13 nfsv4 compound returned 13 Is that useful to anyone? Any hints on to debug this would be greatly appreciated. Server kernel: 2.6.32-40-server (Ubuntu 10.04) Client kernel: 3.2.0-27-generic (Ubuntu 12.04) Same problem with my new server running 3.2.0-27-generic (Ubuntu 12.04). Thanks.

    Read the article

  • Ballooning Mac OS X kernel_task and Wired memory usage. How to diagnose / fix?

    - by user28930
    I have a very strange issue, which I'm having a hard time diagnosing as to the root cause. I have a Mac Pro (2008, 8-core 2.8 GHz, 8800GT) with 14 GB of RAM (recently upgraded because of this issue!). When I boot my system and log in, vm_stat / top / Activity Monitor will show that kernel_task has about 150 MB allocated, and the machine has about 800 MB of Wired memory being allocated. Even initially, 800 MB seems an awful lot of wired memory to be allocated with no applications running - but, it gets worse. (NB: Wired is locked, unswappable memory) After a very short time, sometimes triggered by something as simple as launching a terminal, kernel_task will balloon to 8-900 MB of Real Mem (RSIZE), and Wired Memory will accelerate to 1.6 GB (implying that all the extra memory requests are for wired RAM in the kernel). If I quit everything (I.E: no running applications, bar an activity monitor or terminal to view top), there is no appreciable reduction in either kernel_task RSIZE, or Wired Memory usage. Going the opposite way, and loading the system with tasks also shows that wired memory does not get reduced - and that importantly it is not reduced in preference to heavy swapping. If I log out and log back in again, it reduces a bit (450 MB kernel_task, 1.28 GB Wired), but not back to the start. I'm not running any wacky kexts - and futhermore, kextstat shows no huge memory allocations there; the largest being com.apple.nvidia.nv50hal at about 4 MB of Memory. The machine feels overall more sluggish when this has happened - unsurprisingly because such a huge amount of RAM has been marked as non-pageable. So I have a few questions: 1) Is there a good way to diagnose what has allocated all of this wired memory? It's often over 2 times the kernel_task size, running no applications. The real memory total doesn't seem to add up - it seems that there is a bunch of RAM that isn't being accounted for anywhere. 2) What is happening to cause the kernel to suddenly require 6 times as much memory?

    Read the article

  • mcelog doesn't fails to start PUIAS 6.4 amd hardware

    - by Predrag Punosevac
    Folks, I am a total Linux n00b. I am trying to deploy mcelog on one of my computing nodes running PUIAS 6.4 (i86_64) [root@lov3 edac]# uname -a Linux lov3.mylab.org 2.6.32-358.18.1.el6.x86_64 #1 SMP Tue Aug 27 22:40:32 EDT 2013 x86_64 x86_64 x86_64 GNU/Linux a free clone of Red Hat 6.4 on AMD hardware [root@lov3 mcelog]# lscpu Architecture: x86_64 CPU op-mode(s): 32-bit, 64-bit Byte Order: Little Endian CPU(s): 64 On-line CPU(s) list: 0-63 Thread(s) per core: 2 Core(s) per socket: 8 Socket(s): 4 NUMA node(s): 8 Vendor ID: AuthenticAMD CPU family: 21 Model: 2 Stepping: 0 CPU MHz: 1400.000 BogoMIPS: 4999.30 Virtualization: AMD-V L1d cache: 16K L1i cache: 64K L2 cache: 2048K L3 cache: 6144K NUMA node0 CPU(s): 0-7 NUMA node1 CPU(s): 8-15 NUMA node2 CPU(s): 16-23 NUMA node3 CPU(s): 24-31 NUMA node4 CPU(s): 32-39 NUMA node5 CPU(s): 40-47 NUMA node6 CPU(s): 48-55 NUMA node7 CPU(s): 56-63 My mcelog.conf file is more or less default apart of the fact that I would like to run mcelog as a daemon and to log errors. When I start mcelog [root@lov3 mcelog]# mcelog --config-file mcelog.conf AMD Processor family 21: Please load edac_mce_amd module. However the module is present [root@lov3 mcelog]# locate edac_mce_amd.ko /lib/modules/2.6.32-358.18.1.el6.x86_64/kernel/drivers/edac/edac_mce_amd.ko /lib/modules/2.6.32-358.el6.x86_64/kernel/drivers/edac/edac_mce_amd.ko and loaded [root@lov3 edac]# lsmod | grep mce edac_mce_amd 14705 1 amd64_edac_mod Is there anything that I can do to get mcelog working? The only reference I found is this thread http://lists.centos.org/pipermail/centos/2012-November/130226.html

    Read the article

  • Video card not detected on Lenovo T410 in Linux

    - by wich
    I have a T410 with an nVidia NVS 3100M, this is not a hybrid system, there is no Optimus. (No option in the BIOS for Optimus, lspci in linux as well as the Windows device manager only show the nVidia) Using lspci I see the GPU as a present device, however, I can not, for the life of me, get any video driver to work that will let me start an X session, every time X craps out with the error (EE) No devices detected. I have tried the nVidia binary blob, (with nvidia-config, made sure no nvidia support in the kernel), I have tried nouveau, I have tried nv, I have even tried generic vesa, nothing will work. When I compare the dmesg that I get when loading the nvidia kernel module, I see that it is missing some lines compared with another system that also has an nvidia card, specifically the line mentioning the GPU name (3100M) is not there. I have checked every option in the BIOS, there is nothing to control except for the BIOS video output port, which is set to the LCD panel. I have no idea anymore what the problem may be, or even how I can diagnose this problem further. Any help will be appreciated.

    Read the article

  • centos 6 debuginfo repository does not have httpd debug version available

    - by Zippy Zeppoli
    I am trying to get the debug version of httpd so I can use it in conjunction with gdb. I am having a hard time getting them, and they don't seem to be in the standard epel-debuginfo repository. What should I do? > [root@buildbox-rhel6 ~]# debuginfo-install httpd Loaded plugins: fastestmirror, presto enabling epel-debuginfo Loading mirror speeds from cached hostfile epel-debuginfo/metalink | 8.3 kB 00:00 * base: mirrors.cicku.me * epel: mirrors.kernel.org * epel-debuginfo: mirrors.kernel.org * extras: mirrors.arpnetworks.com * updates: linux.mirrors.es.net epel-debuginfo | 3.1 kB 00:00 epel-debuginfo/primary_db | 487 kB 00:01 Checking for new repos for mirrors Could not find debuginfo for main pkg: httpd-2.2.15-15.el6.centos.1.x86_64 Could not find debuginfo pkg for dependency package apr-1.3.9-5.el6_2.x86_64 Could not find debuginfo pkg for dependency package apr-util-1.3.9-3.el6_0.1.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package db4-4.7.25-17.el6.x86_64 Could not find debuginfo pkg for dependency package expat-2.0.1-11.el6_2.x86_64 Could not find debuginfo pkg for dependency package openldap-2.4.23-26.el6_3.2.x86_64 Could not find debuginfo pkg for dependency package openldap-2.4.23-26.el6_3.2.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package pcre-7.8-4.el6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package glibc-2.12-1.80.el6_3.6.x86_64 Could not find debuginfo pkg for dependency package libselinux-2.0.94-5.3.el6.x86_64 Could not find debuginfo pkg for dependency package zlib-1.2.3-27.el6.x86_64 No debuginfo packages available to install

    Read the article

  • Problem with wireless networking

    - by Rodnower
    Hello, I have atheros wifi hardware, intell chipset, gigabyte laptop and CentOS 5 installed. Now I try to use wireless network and get problems. First of all I want to say that I have 2 OS on my laptop, and when I load Windows XP I still may to access to the wireless network. First I try to get it on Linux was to make active wlan0 interface in: system - administration - network but I get: Determining IP information for wlan0... failed. Second I try also was unsuccessfully: [root 1 network-scripts]# ifup-wireless Error : unrecognised wireless request "off" This relevant output of iwconfig is: Warning: Driver for device wlan0 recommend version 21 of Wireless Extension, but has been compiled with version 20, therefore some driver features may not be available... wlan0 IEEE 802.11 ESSID:"" Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 {output not in the original format} The same things are happen even if I do: modprobe wlan0 (this not get error) Important to say that modprobe not succeed to find ath_pci, tharefor I decide to download latest version of the madwifi driver from http://madwifi-project.org. I extracted this, but when I make this, this is what I get: [root 1 madwifi-0.9.4]# make /bin/sh: line 0: cd: /lib/modules/2.6.18-164.el5/build: No such file or directory Makefile.inc:66: * /lib/modules/2.6.18-164.el5/build is missing, please set KERNELPATH. Stop. I tried to set KERNELPATH, but I think that it was incorrect: [root 1 madwifi-0.9.4]# make KERNELPATH=/lib/modules/2.6.18-164.el5/kernel/ /bin/sh: cc: command not found Makefile.inc:81: * Cannot detect kernel version - please check compiler and KERNELPATH. Stop. Some one have any ideas? Thank you very much for ahead.

    Read the article

  • Ubuntu in VirtualBox File Modified Time in Future and PHP slow file operations

    - by user1750
    For some reason, some of my files have a last modified date in the future. In addition to this, file operations in PHP are SUPER slow. For example, rebuilding the Symfony2 cache can take over 40 seconds (its takes 1-2 on my MacBook Pro). Notice the time for ListingsCRUDController.php. It just says "2012". In order see the date more clearly I ran ls --time-style="full-iso" -l For some reason it shows that this file's last modified date is ~5 hours into the future. System time: To make things more confusing, the system will intermittently speed up. Suddenly, my app will start serving requests in 1-2 seconds (down from 40 seconds) for no apparent reason. I mean I don't do anything to my code/system config - it just changes. Also, during a slow PHP request, the php5-fpm process (nginx) uses 100% of the CPU for the duration of the request. This is the second VM this has happened on and I need to know why its doing this. It has become unusable. Information About My Setup VirtualBox 4.2.0 Host: Macbook Pro Guest: Ubuntu Server 12.04 Package dkms is installed Timezones match for Ubuntu and PHP. Things I've Tried Both Apache and Nginx. APC enabled and disabled. Xdebug enabled and disabled. 1 processor up to 4 processors. 1gb memory up to 4gb memory. I've installed Ubuntu using the regular kernel and the VM kernel.

    Read the article

  • Fedora 9 not reconizing hard drive

    - by Andrew Jones
    I am installing Fedora 9 to a PC (specifications at the bottom) and have had a lot of trouble with it recognising the hard drive. To get the Fedora installer to recognize it in the first place I had to pass "ata_generic.all_generic_ide=1 pci=nomsi" to the kernel, after which it installed OK. However, now when I boot the installed OS, I get a "could not find filesystem '/dev/root'" error. I tried passing the same arguments to the kernel at boot as I did when installing but to no avail. I have tried using the default LVM layout and defining manual ones but it made no difference. There is no option in the BIOS to enable AHCI or anything like that, in fact the BIOS is very limited in most respects. I can get into the system by using the installation CD in rescue mode (with those extra kernal parameters) but I'm not sure what to do once in there... Unfortunately using a more recent version of Fedora or even another Linux distribution altogether isn't an option becuase of outside constraints - which is annoying since I know for a fact Ubuntu works fine on this setup. I have not been using Linux that long, so treat me like an idiot - I am one. Any help would be greatly appreciated, thanks! System spec: Intel Atom Z530 CPU @ 1.6 GHz Intel US15W chipset 1 GB DDR2 160 GB SATA harddisk (Samsung HM16HI) 1000 Mbit/s Ethernet port Phoenix BIOS

    Read the article

  • Windows Server 2008 network speed slow, Xen 3.4.3 HVM ISO

    - by Elliot.Bradshaw
    I've setup a VM running Windows Server 2008 on a host node running Xen 3.4.3-5 and the following kernel: 2.6.18-308.1.1.el5xen #1 SMP Wed Mar 7 05:38:01 EST 2012 i686 i686 i386 GNU/Linux The network speed on the VM is very slow--using the online speed tests I can only get it up to 8-9mbps. The line is 100mbps burstable and the host node has no problem achieving those speeds. If it setup a VM running CentOS, it too has no problems achieving those speeds. I've done some pretty exhaustive troubleshooting, but nothing has helped: New VM installations of Win2k8 do have the same network problem. Upgrading to most recent kernel-xen did not help (2.6.18-308.1.1.el5xen). Upgrading from xen 3.4.0 to xen 3.4.3-5 did not help. Disabling Windows firewall, etc did not help. Changing network card device config from auto negotiation to manually be 100mbps full duplex did not help. Changing the network receive buffer packet size did not help (tried all combos from 64k to 8k). At this point I'm pretty much out of ideas--any help would be appreciated!

    Read the article

  • Instabilities with Bridged and bonded interfaces

    - by Henry-Nicolas Tourneur
    I did post yesterday to get a working setup with several bridged interfaces used for virtual machines (KVM/libvirt). One of the bridged interface is just using eth3 as its ports while the second one (public traffic) is using an ethernet bonded interface. That setup is working but not all the time ! I can start a download from a vm, then it will stop and freeze! So I don't know if my bridge parameters are correct, could you check the below config ? iface eth3 inet manual auto bond0 iface bond0 inet manual slaves eth1 eth2 pre-up ip link set bond0 up down ip link set bond0 down auto br0 iface br0 inet static address 10.160.0.7 netmask 255.255.255.128 bridge_ports eth3 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp on auto br0:1 iface br0:1 inet static address 10.160.0.9 netmask 255.255.255.255 auto br0:2 iface br0:2 inet static address 10.160.0.10 netmask 255.255.255.255 auto br1 iface br1 inet static address 217.4.40.242 netmask 255.255.255.240 gateway 217.4.40.241 pre-up /etc/network/firewall start bridge_ports bond0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp on auto br1:1 iface br1:1 inet static address 217.4.40.252 netmask 255.255.255.255 auto br1:2 iface br1:2 inet static address 217.4.40.253 netmask 255.255.255.255 And yes, it also sometimes speaks about martian on the host: kernel: [249146.055172] martian source 10.160.0.17 from 10.160.0.10, on dev vnet2 kernel: [249146.073122] ll header: ff:ff:ff:ff:ff:ff:54:52:00:76:c3:5c:08:06

    Read the article

  • With Ubuntu 9.10, my DVD keeps spinning up

    - by Ken
    I have Ubuntu 9.10 on my Intel Mac Mini. When there's a DVD in the drive, and even if there's no program open at all (just looking at the desktop), every minute or so the disc spins up with a loud whirring noise, and I can hear it cranking the motor to seek across the disc. How do I find out what's causing this? And how can I make it stop? Thanks! EDIT: I straced nautilus, and saw nothing it's doing directly, even when the disc spins up. It does poll inotify regularly, but I don't know how to trace what it's watching, or if that's even how it receives disc-inserted notifications. It doesn't call inotify_add_watch when I insert a disc or mount it (or eject or umount), but it could be watching all of /dev already or something like that. Of course, a DVD is mounted read-only, so whether it's inotify or something else, it should never need to poll anything on that. And if it is inotify, it's happening in the kernel, and the kernel should really never need to poll a device it's mounted to check for notifications.

    Read the article

  • VMware Workstation reboot 32-bit host when starting 64-bit guest

    - by Powerman
    I'm trying to start 64-bit guest (MacOSX and Windows7) on 32-bit host (Hardened Gentoo Linux, kernel 2.6.28-hardened-r9) using VMware Workstation (6.5.3.185404 and 7.0.1.227600). If VT-X disabled in BIOS, VMware refuse to start 64-bit guest (as expected). If VT-X enabled in BIOS, VMware start guest without complaining, but then, in about a second (I suppose as soon as guest try to switch on 64-bit) my host reboots (actually, it's more like reset - normal reboot procedure skipped and BIOS POST start immediately). My hardware is Core 2 Duo 6600 on ASUS P5B-Deluxe with latest stable BIOS 1101. I've power-cycled system, then enabled Vanderpool in BIOS. My CPU doesn't support Trusted Execution Technology, and there no way to disable it in BIOS. I've rebooted several times after that, sometimes with power-cycled, and ensure Vandertool is enabled in BIOS. I've also run VMware-guest64check-5.5.0-18463 tool, and it report "This host is capable of running a 64-bit guest operating system under this VMware product.". About a year ago I tried to disable hardened in kernel to ensure this isn't because of PaX/GrSecurity, but that doesn't help. I have not checked 32-bit guests with VT-X enabled yet, but without VT-X they works ok. ASUS provide "beta" BIOS updates, but according to their descriptions these updates doesn't fix this issue, so I'm not sure is it good idea to try it. My best guess now it's motherboard/BIOS bug. Any ideas?

    Read the article

  • Copying large files from USB devices to the internal hard drive fails on Mac OS

    - by John M. P. Knox
    I have a second-generation 13" MacBook Air running Mac OS X 10.6.6 with a 2.13 GHz processor, 4 GB of RAM, and a 256 GB SSD hard disk. I often get failures when I attempt to copy a large file or large collection of files from an external USB drive (typically a "Firewire" generation Drobo) to the internal drive. The failure behaves almost exactly as if I had pulled the USB cable from the computer in mid-transfer. I get a warning that I have removed the hard disk improperly. After this event, the drive no longer appears mounted in the finder, and I have to unplug and reinsert the USB cable to mount the drive again. I have also seen a similar problem when using Aperture 3 to import a large number of photos and videos from a USB Compact Flash card reader. The import will fail and I will have to unplug the Card Reader and import the missing items. Oddly, reversing the direction of the copy seems pretty reliable. I've never had a problem copying a large file to a USB device, meaning that I have quite a few large files which are stranded on my Drobo. Model Identifier: MacBookAir3,2 Boot ROM Version: MBA31.0061.B01 I have seen a similar issue reported on Apple's website: http://discussions.apple.com/thread.jspa?threadID=2648590&tstart=0 The only suggested resolutions there seems to be switching to another form of connectivity (e.g. firewire, which does not exist on MacBook Air), or downgrading to Mac OS 10.6.4, or reverting the USB kernel extensions to the 10.6.4 versions: http://discussions.apple.com/message.jspa?messageID=12566073#12582956 I'm not too keen on the idea of downgrading kernel extensions. Does anyone know of a hardware revision without this issue that I can trade up to? Are there any other potential solutions out there?

    Read the article

  • Hyper-V 2008 R2 synthetic networking stops working with linux 2.6.32.15

    - by luxifer
    Hi there, so I thought I'd give Hyper-V on Windows Server 2008 R2 Enterprise a try on my Homeserver (yes, it's legit... got it from msdnaa). First thing to throw at it was my firewall which runs IPFire. This distribution currently uses the kernel version 2.6.32.15 and comes with the Hyper-V drivers. So I enabled them and at first they work just fine but after a few minutes they just fail. There are no packages going in or out anymore until I reboot the VM but sometimes even that won't work so the VM just keeps "Stopping" like forever. Emulated networking works fine but it slow and uses more CPU. That way my firewall routes slower than when running under virtualbox on an atom N270. My server has an E6750; VM is limited to 25%, but that should still outperform this atom CPU especially since it's never going anywhere near 100% CPU load, so give me a break! A quick google search led me to people having the same problem (even with other distributions and kernel versions that include those drivers) but no solution yet... I already found this but I can't quite follow the author on the part where he solved the issue - especially since I need two virtual nics for my firewall distro to work (obviously one internal and one external) What am I missing here?

    Read the article

  • Have an Input/output error when connecting to a server via ssh

    - by Shehzad009
    Hello I seem to be having a problem while connecting to a Ubuntu Server while connecting via ssh. When I login, I get this error. Could not chdir to home directory /home/username: Input/output error It seems like my home folder is corrupt or something. I cannot ls in the home folder directory, and in my usename directory, I can't cd into this. As root I cannot ls in the home directory as well or in any directory in Home. I notice as well when I save in vim or quit, it get this error at the bottom of the page E138: Cannot write viminfo file /home/root/.viminfo! Any ideas? EDIT: this is what happens if I type in these commands mount proc on /proc type proc (rw,noexec,nosuid,nodev) none on /sys type sysfs (rw,noexec,nosuid,nodev) fusectl on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) none on /dev type devtmpfs (rw,mode=0755) none on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) none on /dev/shm type tmpfs (rw,nosuid,nodev) none on /var/run type tmpfs (rw,nosuid,mode=0755) none on /var/lock type tmpfs (rw,noexec,nosuid,nodev) /dev/mapper/RAID1-lvvar on /var type xfs (rw) /dev/mapper/RAID5-lvsrv on /srv type xfs (rw) /dev/mapper/RAID5-lvhome on /home type xfs (rw) /dev/mapper/RAID1-lvtmp on /tmp type reiserfs (rw) dmesg | tail [1213273.364040] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213274.084081] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213309.364038] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213310.084041] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213345.364039] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213346.084042] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213381.365036] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213382.084047] Filesystem "dm-4": xfs_log_force: error 5 returned. [1213417.364039] Filesystem "dm-3": xfs_log_force: error 5 returned. [1213418.084063] Filesystem "dm-4": xfs_log_force: error 5 returned. fdisk -l /dev/sda Cannot open /dev/sda

    Read the article

  • Routing data through VPN in linux

    - by Shadyabhi
    I think its a silly question but still here it goes.. Terminal Output: eth0 Link encap:Ethernet HWaddr 00:1c:c0:37:5e:25 inet addr:10.100.98.51 Bcast:10.100.98.255 Mask:255.255.255.0 inet6 addr: fe80::21c:c0ff:fe37:5e25/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:29677 errors:0 dropped:0 overruns:0 frame:0 TX packets:5209 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3179007 (3.1 MB) TX bytes:610142 (610.1 KB) Memory:e0380000-e03a0000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:76 errors:0 dropped:0 overruns:0 frame:0 TX packets:76 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:9555 (9.5 KB) TX bytes:9555 (9.5 KB) vpn_0 Link encap:Ethernet HWaddr 00:ac:39:95:a1:16 inet6 addr: fe80::2ac:39ff:fe95:a116/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1786 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:128597 (128.5 KB) TX bytes:468 (468.0 B) Actually, I followed this tutorial to setup the PacketiX VPN on ubuntu. Now, how do I actually use this VPN? Terminal Output: shadyabhi@shadyabhi-desktop:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 shadyabhi@shadyabhi-desktop:~$ As told in tutorial, if I do route del default route add default dev vpn_0 I am not able to surf the internet. And I get the route command output as: root@shadyabhi-desktop:/home/shadyabhi# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default * 0.0.0.0 U 0 0 0 vpn_0 root@shadyabhi-desktop:/home/shadyabhi# I know I am not able to route the traffic properly. How do i do that?

    Read the article

  • How do I configure nVidia drivers on a Portable Ubuntu setup?

    - by Nicholas Flynt
    I've been pulling my hair out over this one for a couple of days now, google is no help. I've created a wonderful (until this issue) portable copy of Ubuntu linux that will boot on mostly anything by using a USB enclosure for my laptop's 80GB SATA drive. So far so good, it boots and runs on everything, and on non-nVidia card setups was even detecting the drivers, or letting me install the required drivers for hardware acceleration and compiz. Because you know, the wobble windows are the most awesome thing ever. Anyway, my desktop machine had an nVidia card, so I'm thinking, sure, I'll just install the nVidia drivers like before and everything will work happily. Not so-- now the desktop and any other nVidia cards work great, but it seems to have completely disabled any other graphics cards. When the kernel module detects that an nVidia card isn't present, it shoots up this nasty little dialog box giving me the option to boot into "low graphics" mode, which doesn't even allow me to use the correct screen resolution, much less see the installed graphics card and try to configure a driver for it. Is there any way to configure Ubuntu (with the dreaded nVidia kernel module) so that it can use nVidia's drivers when an nVidia card is present, and default to the normal (not low-graphics) setup in other cases, so that it has a fair chance of using what's actually present? I'm not afraid to much with config files, I just don't know the underlying system well enough to feel comfortable diving in without a push in the right direction. Thanks guys!

    Read the article

  • VNC failure on Xen

    - by BCable
    The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

    Read the article

  • NFS high CPU usage

    - by user269836
    Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

    Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >