Search Results

Search found 3084 results on 124 pages for 'lan'.

Page 93/124 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

• Wifi problems with Ubuntu 13.10

  - by Sparrowhawk4

  I should probably say straight off that I am brand new to Ubuntu. I installed 13.10 alongside Windows 7 a couple of days ago and I've managed to clear up all the little problems, apart from with the wifi. My internet is fine using an ethernet cable. I can connect to the wifi, and it tells me that the signal is good, but for the vast majority of the time I can't load anything, and system monitor tells me that I am sending and receiving nothing. The problem is somewhere in Ubuntu. It works fine on Windows 7, my Android phone and all of my flatmates laptops. I know I'm not the only one with this problem, but the fixes I've seen either don't work or I don't understand them enough to carry them out. Help? EDIT: from lspci command as requested 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 00:1f.6 Signal processing controller: Intel Corporation 82801I (ICH9 Family) Thermal Subsystem (rev 03) 02:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8191SEvA Wireless LAN Controller (rev 10) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 02)

  Read the article

• SSTP client disconnects shortly after successfully connected to VPN

  - by Eran Betzalel

  I'm successfully authenticating and connecting to a SSTP VPN (on windows 2008) from my windows 7 machine, but for some reason, the connection is disconnected about a 1-2 seconds after it's established. I've done the following: Defined a SSTP VPN on my windows server 2008. Defined the same machine as CA. Issued the needed certificates and published them on the client. I'm currently testing this VPN inside my LAN so all the needed ports are opened. Here are the event log entries when trying to connect: Error Log (Client): The user HOME\User dialed a connection named Home VPN which has terminated. The reason code returned on termination is 829. Error Log (Server-VPN): The user HOME\User connected on port VPN0-0 on 7/27/2012 at 1:57 AM and disconnected on 7/27/2012 at 1:57 AM. The user was active for 0 minutes 0 seconds. 312 bytes were sent and 4528 bytes were received. The reason for disconnecting was user request. What would be the issue? How can I resolve or debug it? UPDATE: I've found an event log (Log=System, Source=RasSstp) message on the windows 7 machine that tries to connect to the VPN: The SSTP-based VPN connection to the remote access server was terminated because of a security check failure. Security settings on the remote access server do not match settings on this computer. Contact the system administrator of the remote access server and relay the following information: SHA1 Certificate Hash: 065D681...520375552F SHA256 Certificate Hash: 18DED363...EEEE28CFD00

  Read the article

• Port forwarding on Fortigate 50B

  - by sindre j

  I have serious problems setting up port forwarding on a Fortigate 50B. The unit is basically running as factory default, the wan1 interface is connected to my fibre optic internet modem, and my lan is connected to the internal switch of the Fortigate. The factory default firewall policy allowing traffic from the internal interface to wan1 is kept and I'm able to access the interet as normal. Then I added a virtual ip and a firewall policy for allowing access from the internet to my local servers (ip 192.168.9.51) webserver (standard port 80). The settings I made are as follows. Edit Virtual IP Mapping Name : Server VIP External interface : wan1 Type : Static NAT Extermal IP Address/Range : 0.0.0.0 Mapped IP Address/Range : 192.168.9.51 Port Forwading : not checked Firewall policy Source interface/Zone : wan1 Source address : all Destination interface/Zone : internal Destination address : Server VIP Schedule : always Service : HTTP Action : ACCEPT no other settings checked What happens now is that I'm unable to access internet from my server, I'm not getting through to the webserver from internet either. I'm able to ping a site on the outside, but all web traffic is blocked, both ways. I've checked the documentation, but as far as I can tell I have set this up correctly. Anyone here with knowledge of Fortigate port forwading/NAT?

  Read the article

• Routing static IP traffic on a Comcast Business Class IP Gateway (SMCD3G-CCR)

  - by Jakobud

  We are in the process of replacing our firewall, which is currently the only thing connected to our Comcast Business Class modem. Comcast gives us 5 static IP addresses. Currently, all traffic to all 5 static IPs goes directly to the existing firewall. Eventually, obviously all traffic will goto the new firewall, once the old firewall is removed from the network. But in the meantime, as we will have two firewalls plugged into the same Comcast modem, I need to route certain traffic to the new firewall instead of the old one. The firewall switchover is going to be slow and gradual as I am testing it, so I can't simply unplug the existing firewall and plug in the new one. So my question is, how do I tell the modem to route all traffic that goes to a specific IP to goto the new firewall instead of the old one? I've logged into the web interface for the modem, but the available options aren't very clear. There is a 1-to-1 NAT option (which I can't seem to get the interface for it to work properly) but I also see a "Static Routing" section. I always understood Static Routing to refer to routing data within the LAN though, so I'm not sure if that's what I'm looking for or not. Keep in mind, I'm not looking to do simple port forwarding. I'm wanting 100% of traffic to certain public static IPs to go to the specified connected firewall (I'll deal with service policies there). The modem is an SMC SMCD3G-CCR and is labeled as a Comcast Business Class Business IP Gateway. Any help or direction would be greatly appreciated.

  Read the article

• pfSense: How to route traffic out the WAN port?

  - by Ian Boyd

  Expert version i want to create a route in pfSense that will send traffic out the physical WAN port, not the PPPoE WAN port. i want to talk to talk to the web-server on my DSL modem, but it doesn't see packets wrapped in a PPPoE header. Long version My pfSense router is responsible for setting up the PPPoE connection over DSL to my ISP. When a machine on the LAN wants to sent packets to the internet, the default route sends packets out over the PPPoE connection. Those packets, wrapped in a PPPoE header, are sent on the ethernet cable to my DSL modem. From there they are sent the ISP, and the internet at large. i want a way to send a packet out the WAN port itself - not the PPPoE WAN port. My modem is sitting out there, with a http interface where i can monitor connection speed signal-to-noise ratio bandwidth connection time Whenever i try to set a route for destination of 192.168.2.1 (the IP that the modem will listen to for HTTP requests) to go out the WAN port, they instead end up going out the PPPoE port. The difference being that they're wrapped in a PPPoE protocol packet, and the modem isn't being sent the packet, it's being delivered to the ISP. Given that pfSense has no ability to direct traffic out the physical WAN port: how can i direct traffic out the physical WAN port on pfSense?

  Read the article

• I am getting a SQUID Error

  - by Dave

  Hello, What exactly is wrong here Entry in SQUID File--- httpd_accel_host virtual httpd_accel_port 80 httpd_accel_with_proxy on httpd_accel_uses_host_header on acl lan src 192.168.1.1 192.168.2.0/24 http_access allow localhost Error after: service squid restart 2010/02/01 14:24:29| Processing Configuration File: /etc/squid/squid.conf (depth 0) 2010/02/01 14:24:29| cache_cf.cc(361) parseOneConfigFile: squid.conf:10 unrecognized: 'broken_vary_encoding' 2010/02/01 14:24:29| WARNING: Netmasks are deprecated. Please use CIDR masks instead. 2010/02/01 14:24:29| WARNING: IPv4 netmasks are particularly nasty when used to compare IPv6 to IPv4 ranges. 2010/02/01 14:24:29| WARNING: For now we assume you meant to write /0 2010/02/01 14:24:29| WARNING: (B) '::/4294967200' is a subnetwork of (A) '::' 2010/02/01 14:24:29| WARNING: because of this '::' is ignored to keep splay tree searching predictable 2010/02/01 14:24:29| WARNING: You should probably remove '::/4294967200' from the ACL named 'all' 2010/02/01 14:24:29| WARNING: Netmasks are deprecated. Please use CIDR masks instead. 2010/02/01 14:24:29| WARNING: IPv4 netmasks are particularly nasty when used to compare IPv6 to IPv4 ranges. 2010/02/01 14:24:29| WARNING: For now we assume you meant to write /128 2010/02/01 14:24:29| aclParseIpData: unknown netmask '255.255.255.255' in '127.0.0.1/255.255.255.255' FATAL: Bungled squid.conf line 25: acl localhost src 127.0.0.1/255.255.255.255 Squid Cache (Version 3.1.0.14): Terminated abnormally. CPU Usage: 0.013 seconds = 0.006 user + 0.007 sys Maximum Resident Size: 0 KB Page faults with physical i/o: 0 Also please provide me with the simplest squid script for the proxy to run. Restrictions can be entered. Thanks Dave

  Read the article

• Confusion about Kerberos, delegation and SPNs.

  - by Vilx-

  I already posted this question on SO, but the nature of it is between programming and server configuration, so I'll re-post it here as well. I'm trying to write a proof-of-concept application that performs Kerberos delegation. I've written all the code, and it seems to working (I'm authenticating fine), but the resulting security context doesn't have the ISC_REQ_DELEGATE flag set. So I'm thinking that maybe one of the endpoints (client or server) is forbidden to delegate. However I'm not authenticating against an SPN. Just one domain user against another domain user. As the SPN for InitializeSecurityContext() I'm passing "someuser@mydomain.lan" (which is the user account under which the server application is running). As I understand, domain users have delegation enabled by default. Anyway, I asked the admin to check, and the "account is sensitive and cannot be delegated" checkbox is off. I know that if my server was running as a NETWORK SERVICE and I used an SPN to connect to it, then I'd need the computer account in AD to have the "Trust computer for delegation" checkbox checked (off by default), but... this is not the case, right? Or is it? Also - when the checkbox in the computer account is set, do the changes take place immediately, or must I reboot the server PC or wait for a while?

  Read the article

• Duplicate ping packages in Linux VirtualBox machine

  - by Darkmage

  i cant seem t figure out what is going on here. The Linux machine I am using is running as a VM on a Win7 machine using Virtual Box running as a service. If i ping the win7 Host i get ok result. root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 192.168.1.100 PING 192.168.1.100 (192.168.1.100) 10(38) bytes of data. 18 bytes from 192.168.1.100: icmp_seq=1 ttl=128 time=1.78 ms 18 bytes from 192.168.1.100: icmp_seq=2 ttl=128 time=1.68 ms if i ping localhost im ok root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 localhost PING localhost (127.0.0.1) 10(38) bytes of data. 18 bytes from localhost (127.0.0.1): icmp_seq=1 ttl=64 time=0.255 ms 18 bytes from localhost (127.0.0.1): icmp_seq=2 ttl=64 time=0.221 ms but if i ping gateway i get DUP packets root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 10(38) bytes of data. 18 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.27 ms 18 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.46 ms (DUP!) 18 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=22.1 ms 18 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=22.4 ms (DUP!) if i ping other machine on same LAN i stil get dups. pinging remote hosts also gives (DUP!) result root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 www.vg.no PING www.vg.no (195.88.55.16) 10(38) bytes of data. 18 bytes from www.vg.no (195.88.55.16): icmp_seq=1 ttl=245 time=10.0 ms 18 bytes from www.vg.no (195.88.55.16): icmp_seq=1 ttl=245 time=10.3 ms (DUP!) 18 bytes from www.vg.no (195.88.55.16): icmp_seq=2 ttl=245 time=10.3 ms 18 bytes from www.vg.no (195.88.55.16): icmp_seq=2 ttl=245 time=10.6 ms (DUP!)

  Read the article

• kickstart: reference floppy drive via %ksappend or %include

  - by virtualeyes

  Having trouble getting %ksappend or %include to work when referencing a local floppy drive. Booting off remote server's cd-rom drive I am able to load the CentOS 6 minimal install image, and then add ks=hd:fd0/ks-jvm.cfg to boot params to load kickstart init file from floppy disk. That works fine. The problem is that I want to load a streamlined generic init file off the floppy and then, within the init, %ksappend or %include specific config files relative to the type of server I'm building (JVM, MySQL, Apache, etc.) I do not have DHCP, networking needs to be specified statically, so %ksappend and %include both fail when attempting to reference http://some-LAN-IP/foo.cfg since networking has not yet been set. The kickstart setup only works when I glob in the entire config into a single file, which is great, but ugly and difficult to maintain when I return later, having forgotten the original setup. At this point I'd be happy if I could get %ksappend or %include working with a floppy drive reference in the %post section; that would consolidate a lot of common boilerplate that all kickstarts will rely on (sshd_config, rsync config, resolve.conf, and so on) Thanks for providing the magic floppy drive reference that is eluding me!

  Read the article

• Benchmarking a file server

  - by Joel Coel

  I'm working on building a new file server... a simple Windows Server box with a few terabytes of disk space to share on the LAN. Pain for current hard drive prices aside :( -- I would like to get some benchmarks for this device under load compared to our old server. The old server was installed in 2005 and had 5 136GB 10K disks in RAID 5. The new server has 8 1TB disks in two RAID 10 volumes (plus a hot spare for each volume), but they're only 7.2K rpm, and of course with a much larger cache size. I'd like to get an idea of the performance expectations of the new server relative to the old. Where do I get started? I'd like to know both raw potential under different kinds of load for each server, as well an idea of what our real-world load looks like and how it will translate. Will disk load even matter, or will performance be more driven by the network connection? I could probably fumble through some disk i/o and wait counters in performance monitor, but I don't really know what to look for, which counters to watch, or for how long and when. FWIW, I'm expecting a nice improvement because of the benefits of having two different volumes and the better RAID 10 performance vs RAID 5, in spite of using slower disks... but I'd like to get an idea of how much.

  Read the article

• VMWare Server Windows 2008 NAT Problem

  - by David

  At my new job our workstations run Windows Server 2008. However, for the specific task for which I've been hired, I need to set up a couple Linux VMs. So I grabbed the free VMWare Server and created an Ubuntu image and a Slackware image. (The former to more closely mimic the production server, the latter because I'm more familiar with it.) For desktop security purposes I need to use NAT for the network access (I would have preferred bridged, but I'm told that would go against some policy here and my whole workstation would be sandboxed from the switch). However, I can't seem to get it working right. I can ping out from the VMs to LAN addresses as well as internet addresses. I can resolve DNS names. However, attempts to use a web browser or perform any kind of higher-level interaction like that just time out. Googling around yesterday led me to various workarounds that were similar, but didn't solve my specific situation. (For example, Norton firewall blocking the connection on the host, or even the Windows firewall.) I also saw some forum posts where people said it's a known issue with VMWare and Windows Server 2008 (and Windows 7). So far I haven't been able to find a suggestion that gets me past this roadblock. I'm really not very familiar with managing a Windows Server 2008 box, so it's possible there's just some security setting somewhere that I need to modify. Does anybody have any suggestions on where I should look? UPDATE: I'm now looking at the "Network and Sharing Center" on the host workstation and it shows "VMWare Network Adapter VMnet8" (which is what I'm using) as an "Unidentified network" with "No Internet access." Looks like I can't modify ICS under the group policy. Any suggestions on how to allow this connection to have internet access?

  Read the article

• Static routing on a TP-Link TL-WR1043ND

  - by igor

  My home network setup looks like this: Both routers are TP-Link TL-WR1043ND routers. The basement router handles all devices in the house that are connected via cable, handing out addresses for the 10.89.49.0/24 network via DHCP. Wireless doesn’t really work from the basement, as the signal is too weak, so I have disabled it. To do WiFi, I have added a second (identical) router downstairs. On the WAN side it is assigned the 10.89.49.101 IP address from the basement router, and on its LAN it provides the 10.89.7.0/24 network. Basic internet access works flawlessly from any device this way. I am now facing the problem that I am not able to communicate (e.g. SSH) between all devices, wired or wireless. I am able to connect from a wireless device to a wired device, for example SSH-ing from 10.89.7.X to 10.89.49.Y, but it doesn’t work the other way round—despite the fact that I have added a static route to the basement router: Does anybody have any idea on how to solve it? Both routers have already been upgraded to use the most recent firmware from TP-Link.com (Build 110429), to no avail. Errata: I would like to stick with the official firmware, switching to something like DD-WRT or OpenWrt only as a last resort.

  Read the article

• How do I use a Zyxel P660 router as just modem so that I can connect a WRT54GL router in cascade?

  - by Kenji Kina

  I have a Zyxel P660HW-t1 v2 router (which has a DSL port) and a WRT54GL router (which does not) and the exact same situation as in this thread (UPDATE: the connection between both devices is the important part, since I have been able to set the zyxel router to act as bridge by itself quite nicely. I have accessed my internet connection directly through a PC using PPPoE without any problems, the issues arise when I try to connect the WRT54GL router between the zyxel "modem" and my PCs). I've been trying to use my Zyxel P660 as a modem only: Setup P660 to bridge mode. Changed WRT54GL's IP address to 192.168.2.1 to avoid a conflict on the network. Configured the PPPoE settings as required on WRT54GL. The thing is that when I connect the Zyxel modem/router on the WRT54GL's internet port the light doesn't turn on. I can confirm that this port has been working ok, so I'm not really sure what's going between the devices. I checked several settings such as IPs, tried disabling DHCP on Zyxel/Linksys, Firewall on both and still nothing. Also, I tried connecting Zyxel directly to a computer in bridge mode and dialed successfully. I have even posted a question here before, thinking that what I asked there was the only thing I needed to get things done. Unfortunately it wasn't, and the guy that solved his issue didn't give enough details in his post (and is quite unlikely to give more details since he was an anonymous user). For one, I don't know how to do this part: connected to the Zyxel through telnet and forced LAN port 1 to be at 100mb as well I can't find the option that does this on the zyxel router. Not through telnet or the web admin. Can anyone help me solve this?

  Read the article

• Why are UDP messages from outside the network received but not delivered?

  - by Warren Pena

  I have an Ubuntu Server 10.04 application I've developed that receives messages over a UDP port. The ultimate purpose of this application is to receive messages sent from workers' 3G modems out in the field. If use netcat on either another ubuntu Server or my Vista laptop (both on the same LAN as my test machine) to send a message, the message arrives correctly and appears in my application. However, if I go out to my car and use its 3G modem to send a message from the same Vista laptop, it doesn't work. If I run tcpdump -A, I see the message arrive correctly, but it's never delivered to my application. Clearly, the OS is the one making the choice not to deliver the messages (else they wouldn't appear in tcpdump nor would my app receive them when coming from local machines). I have not installed any firewall software on this machine, nor am I aware of anything installed by default that would block the traffic. sudo iptables --list returns Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I'm not too familiar with iptables, but it looks to me like that's telling it to not do anything. What could be going on that's preventing my messages from being delivered?

  Read the article

• Sonicwall routing between multiple subnets on multiple interfaces

  - by Rain

  As shown by the network diagram below, I have two completely separate networks. One is being managed by a Sonicwall NSA 220, the other by some other router (the brand is not important). My goal is to allow devices within the 192.168.2.0/24 network to access devices in the 192.168.3.0/24 network. Allowing the reverse (192.168.3.0/24 - 192.168.2.0/24) is not required. So far, I have done the following: I connected the X3 Interface on the Sonicwall to the 192.168.3.0/24 network switch (shown as the dashed red line in the diagram). Next, I gave it a static ip address of 192.168.3.254 and set the Zone to LAN (the same Zone for the X0 interface). Judging by various articles and KBs I've read, this is all that should be necessary, although it does not work. I can ping 192.168.3.254 from any device in the 192.168.2.0/24 network although I cannot ping/connect to any device within the 192.168.3.0/24 network. Any help would be greatly appreciated! Network Diagram: (I asked a similar, yet more complicated, question earlier; although, I realized that I cannot solve that without first solving this (which may actually solve my original question))

  Read the article

• My computer loses network connectivity every 30 minutes

  - by Logan Garland

  My LAN connected PC loses network connectivity every 30 minutes. It has a static IP address and I've checked to make sure there aren't any IP conflicts on my network. If I'm streaming from that PC to my Xbox the stream will be interrupted and it normally takes about a minute to come back online. The same happens if I'm actually on the PC and just browsing the web. I'm looking for suggestions on how to track down this issue. I've tried checking the available logs on my router to see if there is an issue with DCHP but have been unsuccessful in finding any evidence. Any suggestions would be helpful. I can't think of any recent changes to my network, PC or software installations that may have caused this. I am a software developer and have intermediate networking knowledge. EDIT: During one outage I told windows to troubleshoot the network problem and it said that it could automatically fix the problem by changing DCHP info. It basically said my network adapter from static to automatically obtain. This did fix the issue quicker than just waiting it out, but the outage occurred again 30 minutes later even when leaving those settings.

  Read the article

• OpenVPN via DD-WRT

  - by user140491

  I am using DD-WRT with my Buffalo G300NH. I notice in my log files: Wed Oct 10 01:08:25 2012 us=343000 Cannot open /tmp/openvpn/dh.pem for DH parameters: error:02001003:system library:fopen:No such process: error:2006D080:BIO routines:BIO_new_file:no such file I have looked at other answers regarding this error. I have tried to no avail. 755 are chmod rights to /tmp/openvpn. At this point, I can not connect outside my LAN via OpenVPN. My server config looks like this: #mode server #tls-server push "route 192.168.11.1 255.255.255.0" push "dhcp-option DNS 10.8.0.1" server 10.8.0.0 255.255.255.0 port 1194 proto udp dev tun0 ifconfig 10.8.0.1 10.8.0.2 #secret /tmp/static.key ca /tmp/openvpn/ca.crt cert /tmp/openvpn/cert.pem key /tmp/openvpn/key.pem dh /tmp/openvpn/dh.pem keepalive 10 120 comp-lzo persist-key persist-tun verb 5 management localhost 5001 Can someone, knowledgeable, of this error kindly help? i have been going on several days, trying to sort it out. I like all nighters though!!

  Read the article

• Win7 Pro x64 task manager hangs when restarting explorer.exe after waking from sleep

  - by Brandon Dybala

  I have a desktop running Windows 7 x64 Pro, set for Hybrid Sleep on a wired network. Wakeup is only enabled from the keyboard (wake on mouse and Wake-On-LAN are both disabled). Sometimes when it wakes up, there is no network connectivity. The notification area icons for both network and volume don't respond to clicks. If I open the Network and Sharing Center, clicking the red X doesn't do anything. Restarting does fix the problem, but I'm looking for a solution that does not require restarting (if at all possible). Drivers are all up to date. I've tried opening Task Manager and restarting the explorer.exe process, but Task Manager freezes for a few minutes, the "New Task" dialog closes, and explorer.exe has not restarted. CPU and memory usage are both normal. One thread suggested making sure the BIOS was set for S3 sleep mode only (not S1 or S1 & S3), but I haven't checked this yet. Going back to sleep and waking back up does not help. So far only a reboot has fixed the issue. System specs: Windows 7 x64 Pro Asus P8Z68-V PRO/GEN3 128 GB Crucial m4 SSD (Firmware version 0309) Intel Core i7 2600 3.4 GHz 16 GB RAM Any ideas? Brandon

  Read the article

• Virtual Machines Renaming/Backing up/Sharing

  - by evan

  I've started using VMware virtual machines for all of my software development projects and have a few questions for others doing the same thing. First, how can you rename the virtual machine and the name of the virtual hard drive? I have a base development machine that I clone for different projects. I'd like to name the machine and it's hard drive according the the project (right now when I copy them via cut and paste, the file names remain the same and I can only organize them by putting them in a specific directory). Second, what is the best way to back up a virtual machine? Is it possible (by breaking the virtual hard drive up into chunks instead of one big file) to get incremental backups working? It seems time machine always tries to make a copy of the whole thing which is time consuming because each virtual machine is around 30GB. Finally, how slow would it be to have a virtual machine shared on an NFS mount on a wireless N network and used from multiple computers (but with only one person using it at a time.) Would it be more reasonable on a gigabit lan connection? Thanks for your input! And please feel free to share any advice or wisdom about using virtual machines for software development and the best ways to speed them up!

  Read the article

• Outbound HTTP performance tuning recommendations

  - by Richard Gadsden

  I'll detail my exact setup below, but general recommendations for a better web-browsing experience will be useful. A nice checklist of things to try would be great! I have 600 users on a single site with an 8MB leased line. I get a lot of moans about the performance of "the internet" (ie web-browsing). What recommendations do the community have for speeding things up without just throwing more bandwidth at it? I expect I will end up buying some more, but good management tips are always valuable. My setup is this: Cisco PIX (515E) firewall on the edge of the network. It's just doing some basic NAT, and opening up a handful of ports to various bastion hosts (aka DMZ servers). The DMZ is just a switch that the servers are plugged into. ISA 2006 Enterprise array (two servers) connecting DMZ to the internal LAN, with WebSense Web Security filtering HTTP traffic so users can't look at porn or waste bandwidth on YouTube during working hours. I've done a few things - I've just switched my internal DNS over to use root hints, which halved DNS query latency from 500ms to 250ms. Well worth doing. I'm trying to cache more aggressively, but so much more of the internet is AJAXy and doesn't cache very well as compared to five years ago. Plus the 70GB of cache which felt like a lot a few years ago really isn't any more. I'm getting about 45% cache hits by number of requests, but only about 22% by size, ie larger objects are less likely to be cached. Latency seems to be part of the problem. Is that attributable to the bandwidth problem, or are there things I can look at to try to reduce latency even on heavily-loaded bandwidth?

  Read the article

• Cannot connect to local network shares when connected to VPN. Error: "the user name could not be found"

  - by Nick G

  I keep finding that on our small company LAN (7 users, 3 servers) that some servers keep becoming "not accessible" for the purposes of file sharing. They display the message "\SERVER is not accessible. You might not have permission to use this network resource. The user name could not be found". But I don't know why "the user name could not be found" as all the machines are on the same domain and the PDC and BDC seem to be behaving OK. EDIT: VPN seems to be the cause: It turns out I can see the server if I use the IP address (\\1.2.3.4\ etc) or the FQ active directory name (eg \server.domainname.local) but not if I use the server name on its own or a mapped network drive originally created from the "short" name. Oddly though, my machine has no issue resolving the server's DNS name as I can ping the machine name OK and it immediately comes back with the IP, however nslookup seems to fail. It seems to be a problem with how Windows looks up machine names when connected to VPNs. When I'm connected to a VPN, windows seems to use the DNS assocated with the VPN and not the one on the domain controller. This behavior to me, seems incorrect as surely that would mean connecting to any VPN would break any ability to lookup local machine names for servers and printers etc. So I guess the real question now is, how can I make my machine still search the local Active Directory DNS (the PDC) even when connected to a VPN? More info in my comments below.

  Read the article

• Short POST data in HTTP

  - by Matt

  We're hosting a customer's Debian Linux web server. It's running a PHP based web application. The server is sitting behind our firewall with it's own virtual interface and port 80 is forwarded internally to a machine sitting in the DMZ. The issue we're having is that when data is posted to the server it seems to be being cut short for some users. It's reproducable for some users on the same box. But the same user sending the same data on the same lan on another PC it works. The data gets cut to around 1140 bytes I'm told. Any idea why this might be happening? The customer is blaming our firewall, but then surely we'd have issues with other services. I'm suspecting it's a problem with the website itself. Suggestions on how to isolate the problem would be of help. Our firewall is Astaro. EDIT: A customer has set the ethernet frame size temporarily to 500bytes on the server. This made it work for now! I know some of the customers are using an internet provider that runs PPPoE

  Read the article

• Why are symbolic links not working in MySQL?

  - by Eno

  I'm having an issue, I searched a lot but I'm not sure if it's related to a previous security patch. On the last version of MySQL on Debian Lenny ( 5.0.51a-24 ) I need to share one table between two db, those two db are in the same path ( /var/lib/mysql/db1 & db2 ). I created symbolic links for db2 pointing to the table in db1. When I query the same table from db2 I get this : 'ERROR 1030 (HY000): Got error 140 from storage engine' This is how it looks : test-lan:/var/lib/mysql/test3# ls -alh drwx------ 2 mysql mysql 4.0K 2010-08-30 13:28 . drwxr-xr-x 6 mysql mysql 4.0K 2010-08-30 13:29 .. lrwxrwxrwx 1 mysql mysql 28 2010-08-30 13:28 blbl.frm -> /var/lib/mysql/test/blbl.frm lrwxrwxrwx 1 mysql mysql 28 2010-08-30 13:28 blbl.MYD -> /var/lib/mysql/test/blbl.MYD lrwxrwxrwx 1 mysql mysql 28 2010-08-30 13:28 blbl.MYI -> /var/lib/mysql/test/blbl.MYI -rw-rw---- 1 mysql mysql 65 2010-08-30 13:24 db.opt I really need those symlinks, is there a way to make them working like before ? ( old MySQL-server is fine ) Thanks,

  Read the article

• How to avoid intrusion detection/anti spoofing issue on a sonicwall TZ series FW

  - by Ian

  We have a sonicwall tz series FW with two internet service providers connected. One of the providers has a wireless service which works a bit like an ethernet switch in that we have an ip with a /24 subnet and the gateway is .1. All other clients on the same subnet (say 195.222.99.0) have the same .1 gateway - this is important, read on. Some of our clients are also on the same subnet. Our config: X0 : Lan X1 : 89.90.91.92 X2 : 195.222.99.252/24 (GW 195.222.99.1) X1 and X2 are not connected, other than both being connected to the public Internet. Client config: X1 : 195.222.99.123/24 (GW 195.222.99.1) What fails, what works: Traffic 195.222.99.123 (client) <- 89.90.91.92 (X1) : Spoof alert Traffic 195.222.99.123 (client) <- 195.222.99.252 (X1) : OK - no spoof alert I have several clients with IPs in the 195.222.99.0 range and all provoke identical alerts. This is the alert I see on the FW: Alert Intrusion Prevention IP spoof dropped 195.222.99.252, 21475, X1 89.90.91.92, 80, X1 MAC address: 00:12:ef:41:75:88 Anti-spoofing is switched off on my FW (network-mac-ip-anti-spoofing - config for each interface) for all ports I can provoke the alerts by telneting to a port on X1 from the clients. You can't argue with the logic - this is suspicious traffic. X1 is receiving traffic with a source IP which corresponds to X2s subnet. Anyone know how can I tell the FW that packets with a src subnet of 195.222.99.0 can legitimately appear on X1? I know whats going wrong, I've seen the same thing before, but with higher end FWs you can avoid this with a few extra rules. I can't see how to do this here. And before you ask why we're using this service provider - they give us 3ms (yep 3ms, thats not an error) delay between routers.

  Read the article

• Format CD-rom on Windows 7 that Windows 95 can read

  - by Joe Majsterski

  I pulled out my ancient Pentium 100Mhz running Windows 95 to play a game from 1996. This game has a critical bug in it that requires a patch. The problem is, the computer has no way to connect to the Internet or to the LAN. I tried burning a CD-rom on my Windows 7 PC to run on the Win95 PC, but it doesn't even recognize that there's a disc in the drive. I did some research, and apparently Windows 95 can't read UDF format. All the solutions recommend, of course, downloading a driver or fix or somesuch, which is my entire problem in the first place. I tried formatting the CD-rom on my Win7 PC, but all the format choices are versions of UDF. Is there a way to get Windows 7 to format in way that is compatible with Windows 95? EDIT: I think the problem may be that I only have CD-RWs. I think a regular CD-R might work, but I can't find any in the house. I'll see if I can scrounge one up and try that.

  Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >