Search Results

Search found 7154 results on 287 pages for 'networking'.

Page 93/287 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

• How to Set Linux Bonding Interface to Gigabit

  - by Kyle Brandt

  I have enabled Linux active backup mode bonding. Each interface is a gigabit interface, but the bond interface seems to end up at 100 Megabit: bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full. ... bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON ... bonding: bond0: backup interface eth1 is now up ethtool apparently can't provide info on bond: sudo ethtool bond0 Settings for bond0: No data available So does this mean I am operating at 100 or 1000 Megabit (My guess is 1000)? If it is only 100, what options in the ifcfg scripts or the modprobe bonding options do I need to sett to make it 1000?

  Read the article

• VPN Network intermittantly fails to provide internet: What could be possible causes

  - by Jake M

  We have a small office with our own VPN setup. We occasionally experience failures in our internet connection where we cannot access the internet. Most of the time the internet connection will resume by itself(without me doing anything) after a period of time(10 mins). Would you be able to suggest possible causes of the connection failure so I can then go and run some tests? Our network architecture is like so: A 'Billion' brand router that is connected to the internet via phone cable and then connected to our Cisco Switch A Cisco Switch/Bus which is connected to all our office nodes, our external harddrive and also to our router as stated above. All connections are via ethernet cable A series of work computers(nodes) connected via ethernet cable to the Cisco switch. Our ISP is TPG Australia We have a Virtual Private Network All the ethernet cables are about 3 years old Do you think that the causes of our intermittant connection problems could be due to the following: Data collisions in the ethernet cables Old/Faulty ethernet cables Our ISP has bad service Can you think of any other causes of the problem?

  Read the article

• Subdomains for different applications on Windows Server 2008 R2 with Apache and IIS 7 installed

  - by Yusuf

  I have a home server, on which I have installed Apache, and several other applications that have a Web GUI (JDownloader, Free Download Manager). In order to access each of these apps (whether be it from the local network or the Internet), I have to enter a different port, e.g., http://server:8085 or http://xxxx.dyndns.org:8085 for Apache http://server:90 or http://xxxx.dyndns.org:90 for FDM http://server:8081 or http://xxxx.dyndns.org:8081 for JDownloader I would like to be able to access them using sub-domains, e.g, http://apache.server or http://apache.xxxx.dyndns.org for Apache, http://fdm.server or http://fdm.xxxx.dyndns.org for FDM, http://jdownloader.server or http://jdownloader.xxxx.dyndns.org for JDownloader First of all, would it be possible like I want it, i.e., both from LAN and Internet, and if yes, how? Even if it's possible only for Internet, I would like to know how to do it, if there's a way.

  Read the article

• "Address already in use" error from socket bind, when ports are not being used

  - by Ivan Novick

  I can not bind (using C or python sockets) to any port in the range: 59969-60000 Using lsof, netstat and fuser I do not see any processes using these ports. Other ports such as 59900-59968 and 60001-60009 I can bind to them. My OS: is CentOS release 5.5 (Final) 2.6.18-194.3.1.el5 There must be something missing? Anyone have any idea how to debug why this port range is not usable? Cheers, Ivan

  Read the article

• No option to connect to wireless network

  - by Casebash

  I don't have any option to connect to wireless. It just doesn't appear in the taskbar at all - even the no wireless networks were found doesn't appear. In network connections, I only have the option of using a wired connection. According to device manager, I have a working VIA Rhine II Fast Ethernet Adapter (this device only appeared after I selected showing hidden devices). I have already attempted restarting the computer a few times. Does anyone have any suggestions?

  Read the article

• Cannot access host from a virtualbox guest using bridged adapter

  - by David Dai

  I have a windows 7 host with firewall turned off. And I have a windowsXP guest running on Virtualbox 4.2.4r81684. In my windowsXP guest I tried to connect to the FTP server on my host machine(which used to work well) but it didn't work. I tried to ping my host machine, but it didn't work either. Then I tried to ping my guest from host, it worked well. my guest ip is :192.168.1.95 my host ip is : 192.168.1.9 route table on guest machine is this: C:\Documents and Settings\wenlong>route PRINT =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...08 00 27 66 54 6c ...... AMD PCNET Family PCI Ethernet Adapter #2 - Packe t Scheduler Miniport =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.95 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.1.0 255.255.255.0 192.168.1.95 192.168.1.95 20 192.168.1.95 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.1.255 255.255.255.255 192.168.1.95 192.168.1.95 20 224.0.0.0 240.0.0.0 192.168.1.95 192.168.1.95 20 255.255.255.255 255.255.255.255 192.168.1.95 192.168.1.95 1 Default Gateway: 192.168.1.1 =========================================================================== Persistent Routes: None arp cache is this: C:\Documents and Settings\wenlong>arp -a Interface: 192.168.1.95 --- 0x2 Internet Address Physical Address Type 192.168.1.1 00-26-f2-60-3c-04 dynamic 192.168.1.9 90-e6-ba-c2-90-2f dynamic It's strange because there was no problem days before and I didn't make any changes to the setting. could anybody help? PS. the guest can communicate with other machines in the LAN(for example 192.168.1.114) ok. it just cannot connect to the host machine.

  Read the article

• I can't externally access my home server's wordpress website

  - by piratepartypumpkin

  Basically, I can access everything just fine using 127.0.0.1, but if I use my external IP (123.123.123.123), I get page not found. My router is port forwarding HTTP port 80 to port 8080 on my servers internal IP address. In other words: (Application: HTTP | Start: 80 | End: 8080 | Protocol: Both | IP Address 192.168.0.101 | Enable [YES]) I know it's forwarding properly, because when I stop port forwarding, I can access my router page by using my external IP. My virtual hosts file is: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /opt/lampstack-5.3.16-0/apps/wordpress ServerName example.com ServerAlias www.example.com </VirtualHost> and my httpd.conf file is: Listen 80 Servername localhost:80 DocumentRoot "/opt/lampstack-5.3.16-0/apache2/htdocs <Directory /> Options FollowSymLinks AllowOverride None Order deny, allow deny from all </Directory> <Directory "/opt/lampstack-5.3.16-0/apache2/htdocs"> Options FollowSymLinks AllowOverride None Order allow, deny allow from all </Directory>

  Read the article

• Event ID 8021 The browser was unable to retrieve a list of servers from the browser master

  - by Ash

  We have a LAN where workstations are randomly losing network connectivity for brief moments of time. The workstations can also take a long time to login to the domain. During our troubleshooting we have found an error log on a few Windows 7 workstations: Warning BROWSER 8021 The browser was unable to retrieve a list of servers from the browser master \\random-pc on the network \Device\NetBT_Tcpip_{BBABCDE9-D8A0-4399-93F2-492FE0848B12}. The data is the error code. What do these errors mean? What computers should have the Computer Browser service enabled, workstations and/or servers? The environment is a mix of Windows 7 & Windows XP workstations on a Windows Server SBS 2011 SP1 domain.

  Read the article

• CentOS Failover Cluster - SIOCADDRT: No such process (when adding a loopback)

  - by Steve Rolfe

  I'm trying to configure two web servers for a load balancing server. The load balancing aspect works fine (it sees both server, kills 'em if it needs to, and seems to direct traffic fine). The only issue is with the servers looping: /etc/sysconfig/network-scripts/ifcfg-lo:0 DEVICE=lo:0 IPADDR=<Virtual IP> NETMASK=255.255.255.255 ONBOOT=yes NAME=loopback Everytime I try a "service network restart" I get a SIOCADDRT: No such process when loading the loopback interface. Anyone have an idea what's causing this?

  Read the article

• All traffic is passed through OpenVPN although not requested

  - by BFH

  I have a bash script on a Ubuntu box which searches for the fastest openvpn server, connects, and binds one program to the tun0 interface. Unfortunately, all traffic is being passed through the VPN. Does anybody know what's going on? The relevant line follows: openvpn --daemon --config $cfile --auth-user-pass ipvanish.pass --status openvpn-status.log There don't seem to be any entries in iptables when I enter sudo iptables --list. The config files look like this: client dev tun proto tcp remote nyc-a04.ipvanish.com 443 resolv-retry infinite nobind persist-key persist-tun persist-remote-ip ca ca.ipvanish.com.crt tls-remote nyc-a04.ipvanish.com auth-user-pass comp-lzo verb 3 auth SHA256 cipher AES-256-CBC keysize 256 tls-cipher DHE-RSA-AES256-SHA:DHE-DSS-AES256-SHA:AES256-SHA There is nothing in there that would direct everything through tun0, so maybe it's a new vagary of Ubuntu? I don't remember this happening in the past.

  Read the article

• How can I run a speed test for Netflix and Hulu?

  - by Brennan Stehling

  Since the FCC rules were struck down I have noticed that Netflix and Hulu often stall on my Time Warner home connection. I've heard others are experiencing the same delays. I use Speedtest.net regularly from my computer and phone to check my connection and typically at home I get 10 to 15Mbps and occasionally higher. Currently it is around 10Mbps yet Hulu is stalling. Is there a way to specifically test my speeds for streaming Netflix and Hulu?

  Read the article

• iptables forwarding between two interface

  - by broody

  So I have a linux box with two wireless interfaces, one is a station and the other an AP. wlan0 (station) - Connected to the internet connection wlan1 (AP) - Other clients connect to it. I would like for clients connected to wlan1 to be able to access the internet on wlan0. And I'd like to do this with iptables as my kernel doesn't have bridging support... Here's what I've tried so far with iptables but it's not working: iptables -A FORWARD -i wlan0 -o wlan1 -j ACCEPT iptables -A FORWARD -i wlan1 -o wlan0 -j ACCEPT I'd appreciate any help.

  Read the article

• second ip address on the same interface but on a different subnet

  - by fptstl

  Is it possible in CentOS 5.7 64bit to have a second IP address on one interface (eg. eth0) - alias interface configuration - in a different subnet? Here is the original config for eth0 more etc/sysconfig/network-scripts/ifcfg-eth0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.91.255 HWADDR=00:1D:09:FE:DA:04 IPADDR=192.168.91.250 NETMASK=255.255.255.0 NETWORK=192.168.91.0 ONBOOT=yes And here is the config for eth0:0 more etc/sysconfig/network-scripts/ifcfg-eth0:0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0:0 BOOTPROTO=static BROADCAST=10.10.191.255 DNS1=10.10.15.161 DNS2=10.10.18.36 GATEWAY=10.10.191.254 HWADDR=00:1D:09:FE:DA:04 IPADDR=10.10.191.210 NETMASK=255.255.255.0 NETWORK=10.39.191.0 ONPARENT=yes How would the resolv.conf file should change since there are two different gateways? Any other change needed?

  Read the article

• Linux: multiple network connections - 3G/4G / Wifi / LAN / etc; how can i set a preferred network connection to use?

  - by Alex

  I've been looking at how I can setup a laptop that has multiple network interfaces, but a problem exists if all the connections are active, i.e. 3G, WiFi and LAN are all connected, I would like it to default to LAN. I would like to set "weights" or "priority" to each connection, so that if the LAN is unplugged, it'll default to WiFi - if its in range and working, otherwise, it'll switch and use the 3G dongle; I've been looking around and I can see that the "metric" counter for route isn't being used for recent kernels. I thought that would be able to set the preferred gateway / connections - but according to the man page: man route: OUTPUT Metric The 'distance' to the target (usually counted in hops). It is not used by recent kernels, but may be needed by routing daemons. So I'm confused, are there any scripts / apps / anything that can detect active network connections, and by way of configuration, send my default gateway network traffic through that interface if its active / alive?

  Read the article

• Can I use a wireless-N laptop as an NAS for seamless and fast data transfer and access?

  - by techaddict

  I have a nice spare laptop (Dell 15R, one year old) that I was wondering if I could use as an NAS. The laptop has an E-Sata port, and I was wondering if I could set it up and plug in a few hard drives permanently (meaning I won't be unplugging it) to the eSata port and use the laptop as a wireless NAS to seamlessly and wirelessly store and access my files. To see more about what I'm looking for in the NAS to see if it's possible to use my other laptop for this purpose, see my other question: Is it possible to have a wireless in-house NAS with wireless data transfer rates of equivalent to SATA speeds? Alternatively, would it be better to sell the laptop and buy a dedicated NAS?

  Read the article

• Diagnosing and debugging LAN congestion / connection issues

  - by John Weldon

  What are the top N tools / methodologies used to diagnose and repair network issues? Given a LAN, for example, where users are able to consistently ping an outside server, but any data intensive connections are flaky; how would you begin solving the network issues? I imagine issues like congestion, bandwidth constraints, throughput constraints, etc. are all factors, but I don't know how to diagnose those issues. I'm especially interested in LAN environments (rather than WAN)

  Read the article

• TCP/IP Ilustrated 1 second edition [on hold]

  - by user196821

  Well, I want to read and learn about how tcpip works in detail, so I got a copy of the well known book of Richard Stevens. But after a little, I discovered there is a second edition of the book, so I checked it out. But surprisingly, the second edition does not cover some subjects that the first actually does (like telnet, ftp, smtp etc...), so I thought "well I just have to read the misshing chapters on the first edition", but if they removed them in the second, it is for a reason. Is there really a good reason for that?

  Read the article

• Where is the actual content in a TCP segment

  - by packetloss

  When I email something or download a program, or do anything else over a network, where in the segment is the actual content? If I am emailing a 20KB word document, and the maximum data field size in a segment is 1500 bytes, does that mean it takes about 14 segments to mail my document wherever it is going? I get, I think, the OSI model and I have a decent grasp of the IP protocol. I think I understand the concept of header wrapping of each successive layer in the protocol stack. What I can't get a definitive answer to is where does the actual content go in a TCP segment? Is that the datagram? Maybe the fact I am asking proves I have no clue... Many thanks.

  Read the article

• Bandwidth Control on our Internet Connection

  - by AlamedaDad

  Hi all, I have Covad dual/bonded T1 service in our office coming through a Cisco 1841 and then through a Sonicwall 3060Pro/Enhanced SW firewall. The problem I'm looking for some input on is how to limit the amount of bandwidth any single user/PC can user for downloading a file from the Internet. It's become an issue that when one person happens to download let's say an ~300MB file, normal internet access for the other employees slows to a crawl. I've seen through MRTG that in fact usage of the circuit jumps to the full 3mb for the duration of the download and then drops. Is it possible to control this? I'm not familiar with QOS or the like so I'm not sure. Any help on this would be appreciated. Thanks...Michael

  Read the article

• Booting off windows image through network

  - by Mr. Sir King Osman

  I have a HP st5742, which is a tower that does not have a hard drive and I am trying to boot it off the network, preferably off an image. It was designed along with the program HP Image Manager, however this program has been discontinued by HP and I can not seem to find a way to get a copy. If this helps, I am running my network with windows server 2008 R2 and would like the streaming client to be running windows. I have spent days searching for a way to deploy this machine however I can not seem to find a straight forward program, guide, or way to do this. I am new to this sort of thing but I willing to reading into the subject, all I need is a point in the right direction. Any help would be greatly appreciated.

  Read the article

• Can I set up multiple accounts on DD-WRT? [closed]

  - by Greg Ros

  Possible Duplicate: Can I set up multiple accounts on DD-WRT? I want to set up multiple accounts on DD-WRT (accounts meaning, username-password pairs). Specifically, I want one to be used primarily for remote web management (though there is no reason to restrict the account to such). Is this possible? If so, how do I go about it? I'm running: Router Model TP-Link TL-WR1043ND Firmware Version DD-WRT v24-sp2 (08/07/10) std - build 14896

  Read the article

• Finding all domain names that resolve to the same ip?

  - by Janak

  Lately I've been tracking a spammer on craigslist. I recently discovered that he's added a new technique to his arsenal, he registered a whole bunch of domain names but they all resolve to the same ip address. Is there any way to take an ip address and get a list of all the domain names that resolve to that ip?

  Read the article

• How do I send traffic to specific IP addresses through VPN and others directly to the internet?

  - by keithwarren7

  I am running Windows 7 and using the Cisco VPN adapter to connect to a private network where I access resources starting with the IP address 172.. My problem is that when connected to the VPN all external traffic is routed through the VPN. I want to set things up so only certain IP addresses go through the VPN and everything else goes out over the local adapter and out to the internet as normal. How?

  Read the article

• Windows 7 can't connect to via ethernet to Airpot Extreme

  - by Mr AJL

  I have an Airport Extreme, and everything works beautifully on the Mac, but my Windows 7 computer, which is connected via a regular ethernet cable, can't see any network. The Windows computer says there's no cable connected. Any ideas? Is there some kind of setting you have to enable with the Airport utility? I looked everywhere but can't find anything. Or do I need to install that Airport utility something on the PC just to connect to the router? (Haven't tried because the PC has no CD drive)

  Read the article

• How to set up DHCP-configured access through a Linux box?

  - by marcusw

  I would like an old desktop box to use my laptop as a router to access the internet. Here is my setup: I have one ethernet port in the side of my laptop which I want to use to get internet access to my desktop computer. The laptop is connected to the LAN via a wireless link. Both systems run Linux. The desktop autoconfigures itself using DHCP. The laptop is a Kubuntu system. I do not have any crossover cables, though wireshark on the laptop sees the DHCP requests from the desktop just fine, so I doubt that I need one. What do I have to do to make this work?

  Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >