Search Results

Search found 2583 results on 104 pages for 'ping'.

Page 93/104 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

• Linux as a gateway (no NAT)

  - by Hugo

  I'm trying to configure a linux server as a gateway/router, but I can't get it to work, and all information I've managed to find is NAT-related. I have a public IP block for the gateway and devices behind it, so I want the gateway to simply route packets to the internet - again: no NATing! I've managed to get the gateway to access the internet successfully (that was just a matter of configuring the IP and GW), and the computers behind it can communicate with it. [EDIT: more info] This is actually an IPv6 block (2800:40:403::0/48) (but I've found that most utilities and instructions can be easily adapted from IPv4 to IPv6 with little hastle). The server has too ports: wan: 2800:40:403::1/48 lan: 2800:40:403::3/48 One of the computers behind it is connected to it via a switch; 2800:40:403::7/48 The wan interface on the server can ping6 www.google.com without issues. The lan interface on the server and the client can mutually ping each other without issues (as well as SSH, etc). I've tried setting the server as a default gateway for the client, with no luck: client # route -A inet6 add default gw 2800:40:403::3 dev eth1 server # cat /proc/sys/net/ipv6/conf/all/forwarding 1 I don't want any filtering/firewalling/etc, just plain routing. Thanks.

  Read the article

• Internet compression proxy for low speed broadband?

  - by user23150

  I live in a rural location, using high-latency wireless off a local ISP's tower. My speed tests vary day to day, but I can get around 1Mb up/down. The problem is, I work with large files, uploading and downloading (HD videos, development software, etc.). It can be painful to wait sometimes. Plus I do some side contract game development, and it can be very difficult to playtest with other developers (200ms ping is a good day for me). Now, obviously it's not going to be easy to solve the latency problem without different wireless hardware. But speedwise, I am wondering if I can use some kind of compression technology on a proxy. For instance, my work computer has full access to a 26Mb down, 10Mb up connection, that is totally unused at night and the weekends. If I could run some kind of compression technology on our server, and use it as a proxy to route to my home computer, I could stand to gain some major speed. I realize that by bogging down a system with compression, I could potentially lose whatever speed gain I had. But the proxy server is a quad core xeon, and the receiving computer is a pretty decent i7 computer, so that shouldn't be a concern. I found http://toonel.net/ but it seems more geared toward very slow narrowband users, like dial-up. Plus, I would prefer to just be able to point my browser to a proxy server, rather then install software on my client machine. EDIT I thought about my question a little more, and realize I am going to need to install software on my client in order to decompress, and possible compress (for uploading). That's not a huge deal.

  Read the article

• Cisco ASA 5505 - InterVLAN NAT Exemptions Implementation not working

  - by Brandon Bearden

  Short version is we cannot communicate between our subnets. We have a Cisco ASA 5505 we are using for our network router. We have a Netgear L3 switch behind that with 10 vlans. Each VLAN is on its own subnet. (10.0.10.x/24, 10.0.11.x/24, etc) So ASA Switch Hosts We have PAT for each subnet to our outside interface. Each subnet NATs out properly. I have NAT exemption enabled for 2 of the subnets (eventually I will need all, but am just testing at the moment). Config is here: http://pastebin.com/pDsG7hsh I have tried multiple ways for the NAT exemption to allow all traffic from our inside VLANS. At this point in time I am trying to get "Engineering" to communicate with all hosts on "AuthUser". I can ping some hosts, but not as many as if I am directly on the interface. I can reach a port 80 service, but not 443. I cannot access anything via hostname or NetBIOS. What am I missing to allow higher security level interfaces to fully communicate with lower security level interfaces? Thx!

  Read the article

• Linux servers in a (primarily) Windows (AD) environment

  - by HannesFostie

  When I arrived at my current position, our environment existed almost exclusively of Windows servers. However, I am a big fan of using Linux for certain applications, like the webgallery I was asked to set up, a simple SFTP server, Nagios for monitoring etc. I do fine setting these up, but not being the Linux expert, I am not sure how to properly join these servers to the domain and was therefor wondering what procedures or guidelines other people follow. We often use ping -a to quickly figure out the hostname of a certain server, but this does not seem to work for the linux machines, most likely because of the whole WINS/NetBios thing I assume. I just joined one server to the domain, but probably missed something cause it's not working even after a dnsflush. Next to that, the couple procedures I've found so far are pretty extensive and most of the time don't seem worth the time. Best case scenario, I download some kind of client (smbclient?), enter the domain name and maybe the server to use, supply an administrator password and that's it. Is that possible at all? Thanks

  Read the article

• How to find out which process is hogging the linux server?

  - by user1149518

  We have a RHEL server. Today it suddenly became slow. Symptoms - It was responding slow to ping queries from other server. When I try to login using ssh, it was taking about 10 seconds to login. I was able to resolve the problem by doing some guess work. I killed one process which I thought was culprit. Which resolved the problem. Though I would like to know what's proper approach to detect the culprit in such kind of "slow server" situations. Le me know proper way to resolving such slowness issues and decting the process causing the slowness. These were the conditions when the server was slow - # vmstat 3 3 procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 1 1 176 6730868 285052 4899676 0 0 3 4 0 0 1 1 97 1 0 0 0 176 6751576 285064 4899704 0 0 0 115 15307 37171 1 1 96 3 0 0 0 176 6751948 285068 4899700 0 0 0 23 14813 39559 1 1 98 1 0 # top top - 16:38:18 up 150 days, 19:36, 64 users, load average: 1.68, 1.46, 1.44 Tasks: 1287 total, 2 running, 1284 sleeping, 1 stopped, 0 zombie Cpu(s): 1.3%us, 1.7%sy, 0.1%ni, 95.9%id, 0.7%wa, 0.0%hi, 0.2%si, 0.0%st Mem: 16620824k total, 9867124k used, 6753700k free, 287424k buffers Swap: 8193140k total, 176k used, 8192964k free, 4898996k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 26258 khk 34 19 130m 47m 7088 S 11.2 0.3 385:32.42 edm Though I would like to know what's proper approach to detect the culprit in such kind of "slow server" situations. Le me know proper way to resolving such slowness issues and decting the process causing the slowness.

  Read the article

• Allow SFTP in iptables

  - by Kevin Orriss

  I have just purchased a VPS from linode and am going through the setup guide. I have everything running (apache2, php, mysql etc) but I am being denied access via SFTP when using fileZilla to upload a file. Now this is my second time installing the server as I missed a section out the first time. I was able to connect to my server through SFTP on filezilla the first time and the thing I missed out was adding a new user and editing the iptables in the firewall. So it would seem that the guide I have been following has blocked SFTP but allowed SSH. Here is the iptables file: *filter # Allow all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT ! -i lo -d 127.0.0.0/8 -j REJECT # Accept all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow all outbound traffic - you can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allow HTTP and HTTPS connections from anywhere (the normal ports for websites and SSL). -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allow SSH connections # # The -dport number should be the same port number you set in sshd_config # -A INPUT -p tcp -m state --state NEW --dport 22 -j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # Log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT All I would like is a line I need to put in there which allows SFTP over port 22. Thank you for reading this.

  Read the article

• Port 80 not accessible Amazon ec2

  - by Jasper

  I have started a Amazon EC2 instance (Linux Redhat)... And Apache as well. But when i try: http://MyPublicHostName I get no response. I have ensured that my Security Group allows access to port 80. I can reach port 22 for sure, as i am logged into the instance via ssh. Within the Amazon EC2 Linux Instance when i do: $ wget http://localhost i do get a response. This confirms Apache and port 80 is indeed running fine. Since Amazon starts instances in VPC, do i have to do anything there... Infact i cannot even ping the instance, although i can ssh to it! Any advice? EDIT: Note that i had edited /etc/hosts file earlier to make 389-ds (ldap) installation work. My /etc/hosts file looks like this(IP addresses as shown as w.x.y.z ) 127.0.0.1   localhost.localdomain localhost w.x.y.z   ip-w-x-y-z.us-west-1.compute.internal w.x.y.z   ip-w-x-y-z.localdomain

  Read the article

• Win7 loses connection to network shares after resume unless server specified using FQDN

  - by Szonja Zemkó

  My Win7 client has a connection to a Linux server and its shared folders. The problem occurs when the computer wakes up after a sleep and then one of the shared folders is not accessible. I receive the following message: Error code: 80070035, The network path was not found. I have problem with one specific folder only. When I restart the computer this problematic folder is accessible again. When I log off before sleep the folder is accessible after wakeup. If I try to access the folder by using the FQDN of the server or the server IP it is also accessible. As a temporary solution I mapped the folder to a network drive using the FQDN and it's working fine but it's inconvenient since every other folder is accessible on the server. To summarize: \server\problematicshare no longer works after resume (the Samba server sees my client connect, then disconnects a few seconds later while I receive the above error message) \server\othershare works after resume \fqdn.of.server\problematicshare always works \ip.of.server\problematicshare always works once the problem manifests, I'm no longer able to restart the "Workstation" service (it is not responding) restarting the "Computer Browser" service has no apparent effect the event log doesn't contain anything that seems relevant "ping server" works

  Read the article

• Why would my network slow down?

  - by monkthemighty

  The network at my work has about 40 computers on it and a quite a few printers. When there are a lot of people working the network will be slow. I can test the ping between my computer and the router and it will keep rising, sometimes to the point that it times out. The router we are using is running Ubuntu on a atom processor and it has 4gb of ram. When the network slows the process Ksoftirq will be using most if not all of the processing power. I have found that Ksoftirq is a process that handles irq requests. Also when the network slows down I have captured packets from the router and using tshark and looked at it using wireshark on my laptop. With the capture show a lot of packets with TCP Dup ACK and TCP Retransmissions. The destinations of the TCP Dup and TCP retransmissions are to most of the computers on the network but there are some that are far more than others. What could this problem be caused by?

  Read the article

• Network outage caused by SMC8013WG Cable Modem/Router ?

  - by mkocubinski

  At work, we have a basic Class C Network. The gateway/router is a SMC8013WG (stock comcast commercial cable modem), and simple unmanaged switch (HP Pro Curve 1400 24G). The SMC8013WG is our default gateway as well as DHCP server. Periodically, I'd say almost every other day.. the entire network will just stop responding. I won't be able to ping/see the gateway, any computers on our local network, or anything on the internet. The only way to fix this is to unplug the Comcast cable modem, wait, and plug back in. This unfailingly fixes the problem. But this doesn't make much sense to me.. shouldn't the network still be fine locally, since everything is plugged into the switch anyway? Why would resetting the router fix this? Can anyone suggest anything to check to in order to narrow this problem down? Just to be clear.. here is the basic topology: { Internet } -- (12.345.67.89) Comcast Cable Modem (192.168.1.1) -- Switch -- 192.168.1.2-254 P.S. Our IT guy is in about 3 hours a day every other week or so, so.. we're kind of on our own most of the time.

  Read the article

• How to prevent response to who-has requests on virtual eth interface?

  - by user42881

  Hi, we use small embedded X86 linux servers equipped with a single physical ethernet port as a gateway for an IP video surveillance application. Each downstream IP cam is mapped to a separate virtual IP address like this: real eth0 IP address= 192.168.1.1, camera 1 (eth0:1) =192.168.1.61, camera 2 (eth0:2) =192.168.1.62, etc. etc. all on the same eth0 physical port. This approach works well, except that a specific third-party windows video recording application running on a separate PC on the same LAN, automatically pings the virtual IPs looking for unique who-has responses on system startup and, when it gets back the same eth0 MAC address for each virtual interface, freaks out and won't allow us to subsequently manually enter those addresses. The windows app doesn't mind, tho, if it receives no answer to the who-has ping. My question - how can we either (a) shut off the who-has responses just for the virtual eth0:x interfaces while keeping them for the primary physical eth0 port, or, in the alternative, spoof a valid but different MAC address for each virtual interface? Thanks!

  Read the article

• Looking for a powershell script that can pull a file from a set of PC's and FTP

  - by DangeRuss

  I'm looking to write a script (preferably powershell) that will essentially copy a file from a bunch of PC's and FTP it to a server. So the structure of the environment is that we have a file on multiple PC's (around 50 or so) that need to placed on a server. Sometimes one of the PC's may be turned off so the script would first need to ensure the PC is up and running (maybe a ping result), then it would need to go into a directory on that PC, pull a file off of it, rename the file, place into a source directory, then remove the file. Naming convention doesn't matter, but date/time stamp would be easiest. Ideally, it would be best to first move all the files to a source directory to save on FTP bandwidth, but since the files will be named the same, the files must be renamed during the move process. Move not copy because the directory needs to be empty so the file can be re-created the next day. So once moved to the source directory, now all the files need to be FTP'd to a server for processing. After all of this, we need to know which PC's on the list did not respond so we can manually retrieve the file so the script should output a file (txt is fine) that will show which PC's were offline. Everything is one domain and script will be run from an server with admin creds. Thank you!

  Read the article

• .bat file - Nagios v3.2 service check and start if stopped

  - by LbakerIT

  I'm just barely getting into programming so I do apologize for my ignorance. I'm trying to create a .bat file that will check if a service is running on XP Pro. If service is running it will exit 0. If the service is stopped start service wait 10 seconds (via ping i'm guessing) check if service is running if service is running exit 0 if service is stopped start service wait 10 seconds Do this check a total of 3 times. if service does not come up within that time: exit 2 Exit 0 = ok exit 1 = warning exit 3 = critical (and this will alert) I need to do this for 3 different services but i'm expecting that it would be better to create one per service. That way you get notified on the specific service that is not coming back up. The goal is that if the service stops it will start it. If after 30 seconds it is unable to start the service then it will send an alert. The reason I'm trying to do it with a .bat is this is consistent with all other scripts and I did not want to complicate it further by adding different kinds of code. Yay for consistency! Again I do apologize for my ignorance I've been thrown into this project last minute. Thank you for the help and reading my question!

  Read the article

• Connection reset to some websites

  - by user143271

  I'm using a 2wire 3600HGV modem/router. Starting around this afternoon, any time I try to access anything from i.imgur.com I get The connection to i.imgur.com was interrupted in chrome, and the actual error is Error 101 (net::ERR_CONNECTION_RESET). It's network wide (tested multiple browsers on multiple computers and phones). I can access imgur.com just fine, but nothing from its content server i.imgur.com. If I disable wifi on my phone and use its 4G connection, I can access it just fine, so obviously imgur isn't down. I haven't changed any configuration on the router, and I have tried changing DNS servers (I tried google and OpenDNS). It also seems that imgur is not the only site; howtogeek and a couple of others seem to have the same problem. It looks like they are all edgecast cdn content servers, but not all edgecast cdn servers fail. Tumblr, for instance, works just fine. Does anyone have any idea what would be causing this? EDIT: Related to the edgecast remark, it would appear that this is a specific edgecast server: gs1.wpc.edgecastcdn.net. Tumbler's content is on gs1.wac.edgecastcdn.net, so it might be on a different server. Edit #2: These sites all respond to ping just fine as well.

  Read the article

• Linux: Three default gateways?

  - by Daniel

  My server has three default gateways, how can that be? Shouldn't there be one default gw? I have three NICs, each attached to a separate subnet: server1:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.5.0.0 * 255.255.255.224 U 0 0 0 eth3 localnet * 255.255.255.224 U 0 0 0 eth0 192.168.8.0 * 255.255.255.192 U 0 0 0 eth1 default 10.5.0.1 0.0.0.0 UG 0 0 0 eth3 default 192.168.8.1 0.0.0.0 UG 0 0 0 eth1 default 10.1.0.1 0.0.0.0 UG 0 0 0 eth0 Sometimes, I can't ping a host on the Internet, sometimes I can. What I want is traffic to the Internet (0.0.0.0) routed through a specific NIC. Can I just add a route for 0.0.0.0 and default gw to one of the eth0-3 interfaces? Will it break my connection? I'm using Debian, here is my /etc/network/interfaces: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 10.1.0.4 netmask 255.255.255.224 network 10.1.0.0 broadcast 10.1.0.31 gateway 10.1.0.1 allow-hotplug eth1 iface eth1 inet static address 192.168.8.4 netmask 255.255.255.192 network 192.168.8.0 broadcast 192.168.8.63 gateway 192.168.8.1 allow-hotplug eth3 iface eth3 inet static address 10.5.0.4 netmask 255.255.255.224 network 10.5.0.0 broadcast 10.5.0.31 gateway 10.5.0.1

  Read the article

• Cannot connect to a shared network drive

  - by dublintech

  I am using windows 7, I cannot connect to a shared network drive on another machine. I can ping the machine. I can remote desktop connect to the machine. The machine is on the same subnet My friend with the exact same laptop as me (and on the same network, same workgroup) can connect to the shared folder. The machine I am trying to connect to and my friends machine can both see shared folders on my machine. I also cannot see shared folders on the friends laptop. When I select diagnose, windows tells me nothing useful. When I select see details on the error pop up, I see: Error code: 0x80004005 (google doesn't help much) I can nbtstat -a the machine who has the shared folder. When I try with my firewall turned off the same happens. I have ensured my windows 7 has all updates. I run security essentials to ensure my laptop is clean. I run ccleaner to clean up my registry. Same error. I have tried with my laptop on both wireless and ethernet. As you can imagine, I am banging my head against the wall on this one.

  Read the article

• Windows 7, network transmit (send) not working

  - by user326287

  My Win 7 works 2 years without problem. But now, I can't transmit (send) big data on LAN/Internet. I can: - Ping anything - Browse Internet, download files at full speed - Send e-mails with very small attachments. - Testing download speed on Speedtest.net, measure stable full speed. I can't: - Testing upload speed on Speedtest.net. Upload stuck.. - Save/send email messages with big (128k) attachment, independent from e-mail provider or e-mail box. THIS IS NOT A HARDWARE/CABLE/CARD OR OTHER NETWORK DEVICES PROBLEM! When I boot from a Linux Live CD, without ANY hardware change, all data sending, testing works correctly, at full speed. I have tried already in Win 7: - Disable Windows/3rd party Firewall completely - Reset IP stack parameters (netsh int ip reset c:\resetlog.txt) - Computer restore - Reinstall LAN driver When I inspect the packets in Wireshark in Windows, I see lot's of (maybe 60% of sent packets) "TCP Retransmission". Sometimes receive "TCP Dup Ack" or "TCP Out-of-Order". Linux don't do this. Thank you for the help.

  Read the article

• Configuring iptables rules for HAProxy and others

  - by MLister

  I have the following relevant settings for HAProxy: defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 500 contimeout 5s clitimeout 15s srvtimeout 15s frontend public bind *:80 option http-server-close option http-pretend-keepalive option forwardfor # ACLs ... I have three backends (including a Nginx server) configured in HAProxy, all listening on different ports of 127.0.0.1. And my iptables config is this: *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -i lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You can modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections # # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE # -A INPUT -p tcp -m state --state NEW --dport 22 -j ACCEPT # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT My questions are: Would the above iptables config work with the settings/options in my HAProxy config? I am also runnning a postgres and a redis server on the same machine, what settings do I need to adjust for these two to enable them work with iptables?

  Read the article

• Connect from Mac OS X to Windows 7 Desktop

  - by jrn

  I am trying to connect from my MacBook to my Windows 7 machine within my own network - if it will work from outside my network that's a plus but no need to have. My Windows 7 machine is freshly installed with Windows 7 Home Premium. It runs the built-in firewall with no settings changed so far as well as Microsoft Security Essentials. So far I tried CoRD and Microsofts Remote Desktop Connections to connect from my Mac to my Windows machine without any success. I did try and disabled the firewall on my Windows machine but could not connect either. The reason I did this was to check wether there is a Windows firewall setting preventing me from connecting. On top of that I manually started the Remote Desktop Services and Remote Desktop Configuration within services.msc. Is there anything else I have to enable for a remote desktop connection? Could there be any router setting I have to tweak? Since I do not want to connect from outside my own network I thought I don't have to do any port forwarding. The error messages I retrieve are all connection timeouts. I can however ping the hostname and/or IP address. Any help would be greatly appreciated. Thanks a lot, jrn

  Read the article

• Website is not accessible from server which is using proxy

  - by Bhoot

  I hosted a website in a win 2008 R2 server which runs in private domain. I set up bindings for port 80 and 443 for http & https respectively. Created inbound rule for port 80 and 443 also in windows firewall. After doing all this, i am still not able to access my website from remote machine. IE : Internet Explorer cannot display the webpage. Chrome : Oops! Google Chrome could not find xxxxxx Tried accessing website by ip address but no luck. I tried to ping that server but it says TTL expired in Transit. Now i found some more information over internet to check if the server is using any kind of proxy in between. I found my IP address at www.getip.com, but ipconfig/all gives me a different IP address. Is it really a problem if we use proxy ? I am not sure if i have concluded it correctly. But is there any way out to resolve this issue? Update ::: I figured it out. I have to call that website with external IP address. due to the proxy settings i was not able to call that website by the server's IP or name of that machine.

  Read the article

• Fedora 17 transparent Ethernet Bridge not forwarding IP traffic

  - by mcdoomington

  I am running on Fedora 17 with the latest ebtables and have been trying to setup a transparent bridge - using the following script, I send a ping through the bridged host and only see the requests on the bridge (among other traffic from eth0), BUT, arps and arp replies are making it through. My host is setup - Client 192.168.1.10 <-- eth0 -- eth2 192.168.1.20 Ethernet script: #!/bin/sh brctl addbr br0; brctl stp br0 on; brctl addif br0 eth0; brctl addif br0 eth2; (ifdown eth0 1>/dev/null 2>&1;); (ifdown eth2 1>/dev/null 2>&1;); ifconfig eth0 0.0.0.0 up; ifconfig eth2 0.0.0.0 up; echo "1" > /proc/sys/net/ipv4/ip_forward; ebtables -P INPUT DROP ebtables -P FORWARD DROP ebtables -P OUTPUT DROP ebtables -A FORWARD -p ipv4 -j ACCEPT ebtables -A FORWARD -p arp -j ACCEPT Any assistance would be great!

  Read the article

• I have just created a subnet for a local network, connecting to a standalone server on another network, now I cannot connect to the internet

  - by Seth

  I am just learning some new aspects of servers and networking. We have a network of 5 subnets that all interconnect with each-other. In order to get two computers on the subnet that we were setting up, I changed the IP from the subnet where the standalone server is on (where they used to be set up)to the local subnet we are remotely hooking up. Likewise I also changed the gateway to coincide with the new subnet. Only problem is that since doing this, I am unable to establish a connection to the internet. I can ping the server and correspong gateway & DNS server, but cannot get connected to the internet. We do have a dumb-switch (non-programmable) connected that receives both the internet and private network inputs and distributes (or should do so) to about 5 other computers. Bottom line, I cannot currently connect to the internet, and am wondering what could be causing this.. It is likely something very obvious and pardon me being more vague than I probably should be, but I could use some help resolving this! Thanks for any help!

  Read the article

• Mail server DNS failed to resolved by Mac clients

  - by Concordus Applications

  We have two internal DNS servers. One is located on a linux server box and the other is the router's DNS management. We set the linux box as primary DNS via DHCP and the router as secondary. We have a few Mac clients that are accessing our internal mail server (hostnamed "mail" internally). When using IMAP or SMTP against the mail server internally, the mac boxes will sometimes fail to locate the server. If I use NSLOOKUP I can see that "mail" is pointed to the correct IP address and is being resolved via the correct DNS server, but if I ping "mail" it fails. ~ (bash)$ nslookup mail Server: 254.254.254.206 Address: 254.254.254.206#53 Name: mail.example.com Address: 254.254.254.205 Note: I replaced our actual internal IP address with 254.254.254.* If I wait a few minutes (3-5 minutes), somehow it resolves itself and sends successfully. This happens multiple times a day. The /etc/hosts file on the mac boxes is the default config. ## # Host Database # # localhost is used to configure the loopback interface # when the system is booting. Do not change this entry. ## 127.0.0.1 localhost 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost Is there something about Mac clients I should know to prevent this failed DNS resolution? Client boxes are: OSX 10.7.4, 8GB RAM, i5 MacBooks Server is: Ubuntu 12.04 Server

  Read the article

• How do I fix a permissions problem with MS Distributed File System?

  - by charlesrandall

  I have a computer that is new, Windows 7, that is supposed to have access to particular network resources on a Distributed File System. However, despite all permissions being set correctly, I have consistent trouble accessing them. For instance, I'm supposed to be able to reach \company.org\main\subdir. All the permissions have been granted, only when I try to access it by name, it tells me I don't have permission to access \main. This is where the fun starts. If I ping company.org, get the IP, replace company.org by the IP, I can then access \IP\main\subdir without any problems at all. However we have a ton of scripts and build tools that access the network resource by name. My sysadmin has found that using MS's dfsutil.exe, we can fix it temporary using this sequence of commands: C:\dfsutil.exe /pktinfo C:\dfsutil.exe /PktFlush C:\dfsutil.exe /SpcFlush C:\dfsutil.exe /PurgeMupCache C:\dfsutil.exe /pktinfo After that, everything is great... until I reboot, or until some unspecified time later where suddenly I don't have access to \main\ anymore. Hoping to find a more permanent solution than waiting for it to break and running a batch file.

  Read the article

• apache fails to connect to tomcat (Worker config?)

  - by techventure

  I have a tomcat 6 with follwoing server.xml: <Connector port="8253" maxThreads="150" minSpareThreads="25" maxSpareThreads="75" enableLookups="false" redirectPort="8445" acceptCount="100" debug="0" connectionTimeout="20000" disableUploadTimeout="true" /> <Connector port="8014" protocol="AJP/1.3" redirectPort="8445" /> and in added worker.properties: # Set properties for worker4 (ajp13) worker.worker4.type=ajp13 worker.worker4.host=localhost worker.worker4.port=8014 and i put in httpd.conf: JkMount /myWebApp/* worker4 It is not working a as trying to navigate to www1.myCompany.com/myWebApp gives "Service Temporarily Unavailable". I checked in tomcat catalina.out and it says: INFO: JK: ajp13 listening on /0.0.0.0:8014 UPDATE: i put mod_jk log level to debug and below is the result: [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_set_time_fmt::jk_util.c (458): Pre-processed log time stamp format is '[%a %b %d %H:%M:%S %Y] ' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_open::jk_uri_worker_map.c (770): rule map size is 8 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_add::jk_uri_worker_map.c (720): wildchar rule '/myWebApp/*=worker4' source 'JkMount' was added [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (171): uri map dump after map open: index=0 file='(null)' reject_unsafe=0 reload=60 modified=0 checked=0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (176): generation 0: size=0 nosize=0 capacity=0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (176): generation 1: size=8 nosize=0 capacity=8 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (186): NEXT (1) map #3: uri=/myWebApp/* worker=worker4 context=/myWebApp/* source=JkMount type=Wildchar len=6 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_set_time_fmt::jk_util.c (458): Pre-processed log time stamp format is '[%a %b %d %H:%M:%S %Y] ' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] init_jk::mod_jk.c (3123): Setting default connection pool max size to 1 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_read_property::jk_map.c (491): Adding property 'worker.list' with value 'worker1,worker2,worker3,worker4' to map. [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_read_property::jk_map.c (491): Adding property 'worker.worker4.type' with value 'ajp13' to map. [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_read_property::jk_map.c (491): Adding property 'worker.worker4.host' with value 'localhost' to map. [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_read_property::jk_map.c (491): Adding property 'worker.worker4.port' with value '8014' to map. [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_resolve_references::jk_map.c (774): Checking for references with prefix worker. with wildcard (recursion 1) [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_shm_calculate_size::jk_shm.c (132): shared memory will contain 4 ajp workers of size 256 and 0 lb workers of size 320 with 0 members of size 320+256 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [error] init_jk::mod_jk.c (3166): Initializing shm:/var/log/httpd/mod_jk.shm.9552 errno=13. Load balancing workers will not function properly. [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'ServerRoot' -> '/etc/httpd' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.list' -> 'worker1,worker2,worker3,worker4' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker1.type' -> 'ajp13' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker1.host' -> 'localhost' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker1.port' -> '8009' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker2.type' -> 'ajp13' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker2.host' -> 'localhost' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker2.port' -> '8010' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker3.type' -> 'ajp13' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker3.host' -> 'localhost' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker3.port' -> '8112' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker4.type' -> 'ajp13' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker4.host' -> 'localhost' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker4.port' -> '8014' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] build_worker_map::jk_worker.c (242): creating worker worker4 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] wc_create_worker::jk_worker.c (146): about to create instance worker4 of ajp13 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] wc_create_worker::jk_worker.c (159): about to validate and init worker4 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_validate::jk_ajp_common.c (2512): worker worker4 contact is 'localhost:8014' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2699): setting endpoint options: [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2702): keepalive: 0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2706): socket timeout: 0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2710): socket connect timeout: 0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2714): buffer size: 0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2718): pool timeout: 0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2722): ping timeout: 10000 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2726): connect timeout: 0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2730): reply timeout: 0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2734): prepost timeout: 0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2738): recovery options: 0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2742): retries: 2 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2746): max packet size: 8192 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_init::jk_ajp_common.c (2750): retry interval: 100 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] ajp_create_endpoint_cache::jk_ajp_common.c (2562): setting connection pool size to 1 with min 1 and acquire timeout 200 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [info] init_jk::mod_jk.c (3183): mod_jk/1.2.28 initialized [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] wc_get_worker_for_name::jk_worker.c (116): found a worker worker4 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] wc_get_name_for_type::jk_worker.c (293): Found worker type 'ajp13' [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_ext::jk_uri_worker_map.c (512): Checking extension for worker 3: worker4 of type ajp13 (2) [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (171): uri map dump after extension stripping: index=0 file='(null)' reject_unsafe=0 reload=60 modified=0 checked=0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (176): generation 0: size=0 nosize=0 capacity=0 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (176): generation 1: size=8 nosize=0 capacity=8 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (186): NEXT (1) map #3: uri=/myWebApp/* worker=worker4 context=/myWebApp/* source=JkMount type=Wildchar len=6 [Wed Jun 13 18:44:26 2012] [9552:3086317328] [debug] uri_worker_map_switch::jk_uri_worker_map.c (482): Switching uri worker map from index 0 to index 1 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_set_time_fmt::jk_util.c (458): Pre-processed log time stamp format is '[%a %b %d %H:%M:%S %Y] ' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_open::jk_uri_worker_map.c (770): rule map size is 8 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_add::jk_uri_worker_map.c (720): wildchar rule '/myWebApp/*=worker4' source 'JkMount' was added [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (171): uri map dump after map open: index=0 file='(null)' reject_unsafe=0 reload=60 modified=0 checked=0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (176): generation 0: size=0 nosize=0 capacity=0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (176): generation 1: size=8 nosize=0 capacity=8 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (186): NEXT (1) map #0: uri=/jsp-examples/* worker=worker1 context=/jsp-examples/* source=JkMount type=Wildchar len=15 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (186): NEXT (1) map #3: uri=/myWebApp/* worker=worker4 context=/myWebApp/* source=JkMount type=Wildchar len=6 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_set_time_fmt::jk_util.c (458): Pre-processed log time stamp format is '[%a %b %d %H:%M:%S %Y] ' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] init_jk::mod_jk.c (3123): Setting default connection pool max size to 1 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_read_property::jk_map.c (491): Adding property 'worker.list' with value 'worker1,worker2,worker3,worker4' to map. [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_read_property::jk_map.c (491): Adding property 'worker.worker4.type' with value 'ajp13' to map. [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_read_property::jk_map.c (491): Adding property 'worker.worker4.host' with value 'localhost' to map. [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_read_property::jk_map.c (491): Adding property 'worker.worker4.port' with value '8014' to map. [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_resolve_references::jk_map.c (774): Checking for references with prefix worker. with wildcard (recursion 1) [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_shm_calculate_size::jk_shm.c (132): shared memory will contain 4 ajp workers of size 256 and 0 lb workers of size 320 with 0 members of size 320+256 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [error] init_jk::mod_jk.c (3166): Initializing shm:/var/log/httpd/mod_jk.shm.9553 errno=13. Load balancing workers will not function properly. [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'ServerRoot' -> '/etc/httpd' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.list' -> 'worker1,worker2,worker3,worker4' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker1.type' -> 'ajp13' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker1.host' -> 'localhost' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker1.port' -> '8009' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker2.type' -> 'ajp13' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker2.host' -> 'localhost' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker2.port' -> '8010' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker3.type' -> 'ajp13' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker3.host' -> 'localhost' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker3.port' -> '8112' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker4.type' -> 'ajp13' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker4.host' -> 'localhost' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] jk_map_dump::jk_map.c (589): Dump of map: 'worker.worker4.port' -> '8014' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] build_worker_map::jk_worker.c (242): creating worker worker4 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] wc_create_worker::jk_worker.c (146): about to create instance worker4 of ajp13 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] wc_create_worker::jk_worker.c (159): about to validate and init worker4 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_validate::jk_ajp_common.c (2512): worker worker4 contact is 'localhost:8014' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2699): setting endpoint options: [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2702): keepalive: 0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2706): socket timeout: 0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2710): socket connect timeout: 0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2714): buffer size: 0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2718): pool timeout: 0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2722): ping timeout: 10000 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2726): connect timeout: 0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2730): reply timeout: 0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2734): prepost timeout: 0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2738): recovery options: 0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2742): retries: 2 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2746): max packet size: 8192 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_init::jk_ajp_common.c (2750): retry interval: 100 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] ajp_create_endpoint_cache::jk_ajp_common.c (2562): setting connection pool size to 1 with min 1 and acquire timeout 200 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [info] init_jk::mod_jk.c (3183): mod_jk/1.2.28 initialized [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] wc_get_worker_for_name::jk_worker.c (116): found a worker worker4 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] wc_get_name_for_type::jk_worker.c (293): Found worker type 'ajp13' [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_ext::jk_uri_worker_map.c (512): Checking extension for worker 3: worker4 of type ajp13 (2) [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (171): uri map dump after extension stripping: index=0 file='(null)' reject_unsafe=0 reload=60 modified=0 checked=0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (176): generation 0: size=0 nosize=0 capacity=0 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (176): generation 1: size=8 nosize=0 capacity=8 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_dump::jk_uri_worker_map.c (186): NEXT (1) map #3: uri=/myWebApp/* worker=worker4 context=/myWebApp/* source=JkMount type=Wildchar len=6 [Wed Jun 13 18:44:26 2012] [9553:3086317328] [debug] uri_worker_map_switch::jk_uri_worker_map.c (482): Switching uri worker map from index 0 to index 1 [Wed Jun 13 18:44:26 2012] [9555:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9556:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9557:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9558:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9559:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9560:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9561:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9562:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9563:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9564:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9565:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9567:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9568:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9566:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9569:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:26 2012] [9570:3086317328] [debug] jk_child_init::mod_jk.c (3068): Initialized mod_jk/1.2.28 [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] map_uri_to_worker_ext::jk_uri_worker_map.c (1036): Attempting to map URI '/myWebApp/jsp/login.faces' from 8 maps [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] find_match::jk_uri_worker_map.c (850): Attempting to map context URI '/myWebApp/*=worker4' source 'JkMount' [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] find_match::jk_uri_worker_map.c (863): Found a wildchar match '/myWebApp/*=worker4' [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] jk_handler::mod_jk.c (2459): Into handler jakarta-servlet worker=worker4 r->proxyreq=0 [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] wc_get_worker_for_name::jk_worker.c (116): found a worker worker4 [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] wc_maintain::jk_worker.c (339): Maintaining worker worker1 [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] wc_maintain::jk_worker.c (339): Maintaining worker worker2 [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] wc_maintain::jk_worker.c (339): Maintaining worker worker3 [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] wc_maintain::jk_worker.c (339): Maintaining worker worker4 [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] wc_get_name_for_type::jk_worker.c (293): Found worker type 'ajp13' [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] init_ws_service::mod_jk.c (977): Service protocol=HTTP/1.1 method=GET ssl=false host=(null) addr=167.184.214.6 name=www1.myCompany.com.au port=80 auth=(null) user=(null) laddr=10.215.222.78 raddr=167.184.214.6 uri=/myWebApp/jsp/login.faces [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] ajp_get_endpoint::jk_ajp_common.c (2977): acquired connection pool slot=0 after 0 retries [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] ajp_marshal_into_msgb::jk_ajp_common.c (605): ajp marshaling done [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] ajp_service::jk_ajp_common.c (2283): processing worker4 with 2 retries [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] ajp_send_request::jk_ajp_common.c (1501): (worker4) all endpoints are disconnected. [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] jk_open_socket::jk_connect.c (452): socket TCP_NODELAY set to On [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] jk_open_socket::jk_connect.c (576): trying to connect socket 18 to 127.0.0.1:8014 [Wed Jun 13 18:44:54 2012] [9555:3086317328] [info] jk_open_socket::jk_connect.c (594): connect to 127.0.0.1:8014 failed (errno=13) [Wed Jun 13 18:44:54 2012] [9555:3086317328] [info] ajp_connect_to_endpoint::jk_ajp_common.c (922): Failed opening socket to (127.0.0.1:8014) (errno=13) [Wed Jun 13 18:44:54 2012] [9555:3086317328] [error] ajp_send_request::jk_ajp_common.c (1507): (worker4) connecting to backend failed. Tomcat is probably not started or is listening on the wrong port (errno=13) [Wed Jun 13 18:44:54 2012] [9555:3086317328] [info] ajp_service::jk_ajp_common.c (2447): (worker4) sending request to tomcat failed (recoverable), because of error during request sending (attempt=1) [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] ajp_service::jk_ajp_common.c (2304): retry 1, sleeping for 100 ms before retrying [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] ajp_send_request::jk_ajp_common.c (1501): (worker4) all endpoints are disconnected. [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] jk_open_socket::jk_connect.c (452): socket TCP_NODELAY set to On [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] jk_open_socket::jk_connect.c (576): trying to connect socket 18 to 127.0.0.1:8014 [Wed Jun 13 18:44:54 2012] [9555:3086317328] [info] jk_open_socket::jk_connect.c (594): connect to 127.0.0.1:8014 failed (errno=13) [Wed Jun 13 18:44:54 2012] [9555:3086317328] [info] ajp_connect_to_endpoint::jk_ajp_common.c (922): Failed opening socket to (127.0.0.1:8014) (errno=13) [Wed Jun 13 18:44:54 2012] [9555:3086317328] [error] ajp_send_request::jk_ajp_common.c (1507): (worker4) connecting to backend failed. Tomcat is probably not started or is listening on the wrong port (errno=13) [Wed Jun 13 18:44:54 2012] [9555:3086317328] [info] ajp_service::jk_ajp_common.c (2447): (worker4) sending request to tomcat failed (recoverable), because of error during request sending (attempt=2) [Wed Jun 13 18:44:54 2012] [9555:3086317328] [error] ajp_service::jk_ajp_common.c (2466): (worker4) connecting to tomcat failed. [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] ajp_reset_endpoint::jk_ajp_common.c (743): (worker4) resetting endpoint with sd = 4294967295 (socket shutdown) [Wed Jun 13 18:44:54 2012] [9555:3086317328] [debug] ajp_done::jk_ajp_common.c (2905): recycling connection pool slot=0 for worker worker4 [Wed Jun 13 18:44:54 2012] [9555:3086317328] [info] jk_handler::mod_jk.c (2615): Service error=-3 for worker=worker4 The error i get in browser is: Service Temporarily Unavailable Apache/2.2.3 (Red Hat) Server at www1.myCompany.com.au Port 80 can someone please help and explain what is going on and how it can be resolved?

  Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >