Search Results

Search found 9381 results on 376 pages for 'wireless driver'.

Page 93/376 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

• Problem with usb driver: ti_usb_3410_5052

  - by alschbpk

  I have problems with my USB driver. After adding my device (MSP430 USB-DEBUG-INTERFACE) it doesn't work. [ 60.476039] usb 2-2.1: new full speed USB device using uhci_hcd and address 8 [ 60.693959] ti_usb_3410_5052 2-2.1:1.0: TI USB 3410 1 port adapter converter detected [ 60.693981] ti_usb_3410_5052: probe of 2-2.1:1.0 failed with error -5 I try to do: modprobe ti_usb_3410_5052 No changes. It's Linux Linux ubuntu 2.6.35-25-generic #44-Ubuntu SMP Fri Jan 21 17:40:44 UTC 2011 x86_64 GNU/Linux I hope someone can help me.

  Read the article

• Wireless NAS - options?

  - by Jinx999

  I want to put a NAS drive in an upstairs room (out of the way) but I believe most NAS drives need to be connected to the router. My router is hooked up close to the phone socket downstairs in a spot where we would rather just have the phone. Is there anyway to set-up a NAS drive without hooking it up directly to the router (e.g. wireless) or, better still, is there a way to move the router upstairs as well without significant recabling?

  Read the article

• VMWare Workstation 8 reporting ""vmx86 driver version invalid handle" problem on booting VM

  - by dommer

  I'm just doing a VMWare Workstation 8 installation. However, on trying to boot (or create) a VM, it's reporting "Could not get vmx86 driver version: The handle is invalid." It recommends reinstalling, which I've done. Also, VMWare Player just hangs. Was going to post on the VMWare forums, but can't seem to create a new discussion (even though I've registered/logged in). It's our own fault for being too eager to upgrade, I guess.

  Read the article

• Affordable Wireless Speakers For the Whole House?

  - by javamonkey79

  Does anyone know of any affordable speakers that you can hook up to a HTPC\Media Center and then take the speakers anywhere around the house to listen to them? Basically, what I've found has either been headphones that do this or wireless speakers that site on the desktop. Affordable to me would be $50-100. I think I've seen some options for hundreds of dollars - but I'm looking for something simple that I can use around the house. TIA.

  Read the article

• Impossible to Remove FTDI driver / FTDI Enumeration on Windows 7

  - by Joe

  I have already read the : Is it possible to reset FTDI virtual com ports enumeration, we easily get hundreds of COM ports in production environment topics which was pretty interesting ! But I got a problem, apparently I can't delete the ftdi driver, so I can't use the previous conclusion of the topic... I'm really stuck and bored of this problem, my com port number is 132 ! Does someone have another solution ?

  Read the article

• Computer not turning off after windows shuts down printer driver

  - by Confused

  The power is not shutting off my computer after windows shuts down. Windows shuts down and I hear my computer case "click" but the power and fans all stay on. This seemed to start after I installed the canon pixma printer driver and software from their website. I have uninstalled the printer software from "uninstall program" and deleted the printer from printers. I have even stopped spool service and deleted printer following this post, the printer drivers did uninstall. How to completely remove printer from Windows 7

  Read the article

• Wireless USB Print Server for use with both Linux and Windows

  - by John

  I am looking for a wireless usb print server that will work with my netbook running ubuntu and my main pc running windows. There seems to be little information on anything that works with both reliability. Dose anyone know of anything that will work? thanks

  Read the article

• Wireless Network suddenly cant connect after Windows update

  - by vinir

  UPDATE: As my patience started to end, the laptop started to display symptoms of other malfunctions, so I ended up returning it to Asus and actually had the price of the laptop back in store credit. I did not solve the problem per se, but as I don't have the notebook and the screen, the keyboard, the touchpad and other parts were malfunctioning, I can safely assume that it was put to rest. I don't know how to behave when my question isn't actually answered, but was "solved", so I placed this over here. Anyone that knows how to end this topic, I would appreciate the heads up. Thanks for everything, everyone, it's nice to see that this topic in the community was active even when all this time had passed. vinir So I bought an ASUS K43E notebook earlier this year and built a wireless conection to link it to. It worked great for the first weeks, but then I updated my Windows 7 Home Basic with the daily updates; After that my home network couldn't be reached no matter what I did. I have linux on dual boot on the same notebook and it can connect to my home wireless network flawlessly. I have a hunch that it's somehow related to the Network Profile settings. I have noticed my network was set as "Home network", but after the system updates I got changed to "Public". Now I can't connect to it to change the profile settings. My Atheros Network adapter is updated to the latest driver (march 2012), and I still can't connect. The funny thing is that the same thing happened to my mother's notebook, as it has the same Network Adapter, Atheros AR9285, as I recall it. I managed to fix it on my mother's computer by using an specific network LSP and profiling reset that was available through her notebook's antivirus program, avast! Internet Security. I can't get that to work on my notebook, but I suspect that some related tool might just make it work too. So the question is: how to modify a network's profile and settings that were stored in my notebook? I can't connect to the specific network on Windows, as stated before.

  Read the article

• What to do when a device has no driver for Windows 7 but it has Vista, XP drivers

  - by Mehper C. Palavuzlar

  This has always been a bothersome matter for me. Some devices (printers, scanners, etc.) have drivers for older versions of Windows (Vista, XP, 2000, NT) but no driver for Windows 7. What are my chances to install such devices on Windows 7? Example case: I have a Sharp printer & scanner (Sharp AR-122E N) which I have used for my old Windows XP based PC. Now I want to install it on a Windows 7 x64 based PC. Windows 7 cannot load its driver. I used the original driver CD but when I run the setup.exe (which is included in AR122EN111.exe, 6713KB), it says Cannot install driver on this operating system. Supported operating systems are: Windows 2000, XP, Vista. I tried to install the driver using compatibility settings. I tried Windows Vista and Windows XP SP3, but to no avail. The setup gave the same error. I also googled for Windows 7 driver for "Sharp AR-122E N" but it only listed the original driver that I tried. The official site of Sharp does not even list the driver for this product. In the past, the compatibility setting workaround did work for some devices, but this time it failed. What else can I do to overcome this problem?

  Read the article

• Is it possible to automate a driver change on Windows for a plug&play peripheral ?

  - by Gnoupi

  Is it possible to automate a change of driver for a same peripheral, under Windows ? Typically to switch between two ones. (I'm talking about the kind of driver which doesn't require the computer to reboot, typically). I have a peripheral for which I use the constructor's driver in some cases, but also a modified driver in other cases. Not that the changing driver is really annoying, but I would like to know if it would be possible to make it easier, like for example in a shortcut. I know the name of the driver, even which files involved. For more details, the concerned peripheral is a "Xbox360 Gamepad for Windows" (or something like this). The base driver is good for new games, but it doesn't handle correctly older ones (some issues with axes, and vibrations). The modified driver makes it behave like a classic controller, but then it doesn't work correctly on new games (typically using the new version of dxinput linked to the "Games for Windows"). However, this is not a question specific to this gamepad, I'm asking in general about automating this change of drivers. I currently use Windows XP, so my question is mostly about it, but I'm also interested in the same issue for later versions (Windows 7, most likely). I'm not really sure if this is even possible, but in case someone has an idea, I'm asking.

  Read the article

• Linksys WRT54GC v2.0 - all connection lights flashing

  - by JC Denton

  I have just received a Linksys WRT54GC router of a friend. Apperantly it has stopped working. All lights on it are flashing apart from the power and wireless light. I have read of similar issues online but not ones describing the same set of lights flashing. I have tried connecting to the device over ethernet but failed. It's no longer accessible over wireless either. I've also tried to run the linksys utility on the cd but it failed to detect the presence of the device (attempted over ethernet, firewall switched off). I've tried pressing the reset button for 30 seconds and disconnection the power cable for 30 seconds but to no avail. Thanks for any thoughts

  Read the article

• How to stop intermittent playback on airtunes (iTunes + Airport Express)?

  - by Alex B

  Is there a definitive answer for how to stop intermittent "skips" or pauses while playing music from iTunes to an airport express connected to my home stereo? When I read other forums I see a wealth of posts that say "I did XYZ and it's fixed" followed by "I tried XYZ and it didn't work." This does not appear to be signal strength related. The green light on the Airport Express does not turn to yellow/orange. Other wireless devices have no trouble connecting at the same or greater distances from the wireless router.

  Read the article

• Share laptop's Wi-Fi with a LAN connection and a mobile device

  - by xperator

  OS: Windows 7 64bit I want to share my laptop's internet connection between my PC and my Android device. But I can only do one of them at a time. The laptop is connected to internet wirelessly. The PC is connected to the laptop using a Ethernet cable and internet is shared between them. I want to connect my mobile device to my laptop by making the laptop into a Wi-Fi hotspot. PC (Ethernet) == Laptop (connected to net by Wi-Fi) <== Mobile device (Wi-Fi hotspot) I have 3 connections in my laptop: Wireless Network Connection (internet - shared) Local area connection (PC) Wireless Network Connection 2 (Wi-Fi hotspot) Every time I have to disable either the LAN to get the Wi-Fi hotspot working, or disable the Wi-Fi hotspot to get LAN working. How can I share so I can use both at the same time?

  Read the article

• Copying files from NAS to NAS drives

  - by user1001421

  Very simple question. I've got 2 NAS drive that are "wire" connected via a router. If I have a wireless laptop and request a large amount of data be copied from one NAS drive to the other, does the network traffic go direct from the one drive to the other, going via the wired network, or does the network traffic go via my laptop, if you see what I mean. IE. From the NAS drives wired network, to the wireless network and then back to the wired network. Is this a common bottle-neck when copying a large amount of data? And if so, is there a way to avoid it. Thanks.

  Read the article

• Should I use 802.11n with a 15 Mbps ISP (Comcast Cable)?

  - by stackoverflowuser2010

  I currently own a LinkSys-WRT54GL 802.11a/b/g wireless router, and my ISP is Comcast Cable providing me with 15 Mbps (that's bits per second, I believe) download speed. I am wondering if there is any benefit with using an 802.11n wireless router to access the Internet? The maximum theoretical speed of the WRT54GL router is 54 Mbps (802.11g), which is faster than the 15 Mbps provided by my ISP. I know that 802.11n has a max bandwidth of 300 Mbps, and it would help for intra-house transfers, such as streaming video from one computer to another. But is there any benefit to 802.11n for Internet activity, such as web browswing, gaming, and streaming video from Netflix?

  Read the article

• broadcom 5722 NIC not installed on Ubuntu Server, although driver present

  - by Bastien

  Hello, I just installed Ubuntu Server 10.04 LTS, running kernel 2.6.32-24-server, on a brand new Dell T110 server, supposedly fully compatible with Ubuntu Server. I have two NICs: one ONBOARD, the other additional on PCI. both of them are Broadcom netXtreme 5572. on the first boot of the system, I could see both cards as eth0 and eth1 (with ifconfig) I configured eth0 as static IP (as planned), and did not configure eth1. after rebooting, one of the two NICs "disappeared": it does not appear in ifconfig at all. the one that disappeared is the ONBOARD one. I investigated a bit and found the following things: the card is SEEN, but not "installed", it appears as "UNCLAIMED" in lshw: *-network UNCLAIMED description: Ethernet controller product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress cap_list configuration: latency=0 resources: memory:df9f0000-df9fffff *-network description: Ethernet interface product: NetXtreme BCM5722 Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 00 serial: 00:10:18:60:23:64 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.102 duplex=full firmware=5722-v3.09 ip=10.129.167.25 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:35 memory:dfaf0000-dfafffff so I checked my dmesg and found a few strange lines, showing, there actually is a problem bringing up this card: [ 3.737506] tg3: Could not obtain valid ethernet address, aborting. [ 3.737527] tg3 0000:04:00.0: PCI INT A disabled [ 3.737535] tg3: probe of 0000:04:00.0 failed with error -22 [ 3.737553] alloc irq_desc for 17 on node -1 [ 3.737555] alloc kstat_irqs on node -1 [ 3.737560] tg3 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 3.737566] tg3 0000:05:00.0: setting latency timer to 64 [ 3.793529] eth0: Tigon3 [partno(BCM95722A2202G) rev a200] (PCI Express) MAC address 00:10:18:60:23:64 [ 3.793532] eth0: attached PHY is 5722/5756 (10/100/1000Base-T Ethernet) (WireSpeed[1]) [ 3.793534] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 3.793536] eth0: dma_rwctrl[76180000] dma_mask[64-bit] that actually shows that one NIC is recognized, the other is not. I researched a bit more, with lspci -v: 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: fast devsel, IRQ 16 Memory at df9f0000 (64-bit, non-prefetchable) [size=64K] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 00-00-00-fe-ff-00-00-00 Kernel modules: tg3 05:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Subsystem: Broadcom Corporation NetXtreme BCM5722 Gigabit Ethernet PCI Express Flags: bus master, fast devsel, latency 0, IRQ 35 Memory at dfaf0000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at <ignored> [disabled] Capabilities: [48] Power Management version 3 Capabilities: [50] Vital Product Data <?> Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number 64-23-60-fe-ff-18-10-00 Capabilities: [16c] Power Budgeting <?> Kernel driver in use: tg3 Kernel modules: tg3 here I could see that the MAC address is 00-00-00-FE-FF-00-00-00, which, according to some forum posts on several websites, could be an issue. I've researched everything I could on the net, and found out several people having slightly comparable issues, but they usually involve different HW, and do not provide a proper explanation / solution... I would appreciate if anyone around here has some info to share ! thanks

  Read the article

• Can't set-up Wifi Adhoc on my Raspberry Pi with an USB dongle

  - by Wouter

  I am trying to set-up an access point (ad-hoc) for my Raspberry Pi. That means I'm trying to "share" the ethernet connection over Wi-Fi. I am doing this using my Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter. When following a tutorial (or actually every tutorial), it immediately goes wrong. root@pinkypi:/home/pi# iwconfig wlan0 mode ad-hoc Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Device or resource busy. I already tried ifdown and not having it in the USB port at the startup. If it helps, every action with the thing fail (or at least setting the mode). I am using Debian. I'm sure I'm overseeing something, but I can't find out what. What is wrong?

  Read the article

• How to setup Dual Head with "radeon" driver for R770?

  - by user1709408

  I want to make dual head setup without xrandr but with Xinerama. I put "Screen 1" line into xorg.conf, but card still show identical output on DVI-2 and DVI-3 It is important to use xinerama for me (to glue three monitors), that's why i decide not to use ranrd (randr is incompatible with xinerama as i read somewhere) Here is my videocard (HD 4850 X2): lspci | grep R700 03:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI R700 [Radeon HD 4850] 04:00.0 Display controller: Advanced Micro Devices [AMD] nee ATI R700 [Radeon HD 4850] Here is how monitors are connected: grep "DVI" /var/log/Xorg.0.log [ 1210.002] (II) RADEON(0): Output DVI-0 using monitor section Monitor0 [ 1210.048] (II) RADEON(0): Output DVI-1 has no monitor section [ 1210.079] (II) RADEON(0): EDID for output DVI-0 [ 1210.080] (II) RADEON(0): Printing probed modes for output DVI-0 [ 1210.128] (II) RADEON(0): EDID for output DVI-1 [ 1210.128] (II) RADEON(0): Output DVI-0 connected [ 1210.128] (II) RADEON(0): Output DVI-1 disconnected [ 1210.128] (II) RADEON(0): Output DVI-0 using initial mode 1920x1200 [ 1210.160] (II) RADEON(1): Output DVI-2 using monitor section Monitor2 [ 1210.215] (II) RADEON(1): Output DVI-3 has no monitor section [ 1210.246] (II) RADEON(1): EDID for output DVI-2 [ 1210.247] (II) RADEON(1): Printing probed modes for output DVI-2 [ 1210.299] (II) RADEON(1): EDID for output DVI-3 [ 1210.300] (II) RADEON(1): Printing probed modes for output DVI-3 [ 1210.300] (II) RADEON(1): Output DVI-2 connected [ 1210.300] (II) RADEON(1): Output DVI-3 connected [ 1210.300] (II) RADEON(1): Output DVI-2 using initial mode 1920x1200 [ 1210.300] (II) RADEON(1): Output DVI-3 using initial mode 1920x1200 Here is my /etc/X11/xorg.conf Section "ServerFlags" Option "RandR" "0" Option "Xinerama" "1" EndSection Section "ServerLayout" Identifier "Three Head Layout" Screen "MyPrecious0" Screen "MyPrecious2" RightOf "MyPrecious0" Screen "MyPrecious3" LeftOf "MyPrecious0" EndSection Section "Screen" Identifier "MyPrecious0" Monitor "Monitor0" Device "Device300" EndSection Section "Screen" Identifier "MyPrecious2" Monitor "Monitor2" Device "Device400" EndSection Section "Screen" Identifier "MyPrecious3" Monitor "Monitor3" Device "Device401" EndSection Section "Device" Identifier "Device300" BusID "PCI:3:0:0" Screen 0 Driver "radeon" EndSection Section "Device" Identifier "Device400" BusID "PCI:4:0:0" Screen 0 Driver "radeon" EndSection Section "Device" Identifier "Device401" BusID "PCI:4:0:0" Screen 1 Driver "radeon" EndSection Section "Monitor" Identifier "Monitor0" EndSection Section "Monitor" Identifier "Monitor2" EndSection Section "Monitor" Identifier "Monitor3" EndSection I tried to switch to vesa driver (didn't work for me) I tried to add options like Option "ZaphodHeads" "DVI-2" and Option "ZaphodHeads" "DVI-3" into sections "Device 400" and "Device 401" (this didn't help because "ZaphodHeads" option is for ranrd, and randr is disabled by decision) I tried to merge sections "Device 400" and "Device 401" into one section and add Option "ZaphodHeads" "DVI-2,DVI-3" (see comment about randr above) single section setup helps to change log line RADEON(1): Output DVI-3 has no monitor section into RADEON(1): Output DVI-3 using monitor section Monitor3 but nothing was enough to switch from screen cloning to separate screens. This problem (lack of documentation on radeon driver) is similar to these: Radeon display driver clones monitors while using Xinerama (moderators decision to close that problem was wrong) Ubuntu 12.10 multi-monitor setup isn't working The problem is solvable, because this hardware worked as three headed for me earlier with gentoo/xorg-server-1.3 Xorg -configure creates setup for the first monitor on the first GPU Please don't advise to use fglrx/aticonfig/amdcccle (this goes against my religion beliefs)

  Read the article

• Mac OS X: network disabled because security breach

  - by fireeyedboy

  Dear all, I just recieved a message on my Mac OS X system telling me (loosely translated from Dutch): "The network has been temporarily disabled because the network's security was breached." (It's a wireless WPA2-PSK secured network BTW) I looked in the logs of my router (a Zyxel P-2602HW-D1A) only to see a few (outbound) "syn flood TCP ATTACK" logs, but those were from like a week ago, other than that nothing. What tools on Mac OS X do I have to analyse this security breach occurence? Are there some security logs on Mac OS X that I can inspect? What other measurements should I take? And how serious should I take this warning from Mac OS X? System: Macbook Pro Intel Core 2 Duo 2.2 Ghz OS: Mac OS X 10.5.8 Network: wireless WPA2-PSK Relevant software: Parallels Desktop with Windows XP (was open, but stopped at the time) Other systems on my network: Windows XP SP3 desktop (was running at the time) If you need any more info, don't hestitate to ask. Thanks in advance.

  Read the article

• How to get Windows 7 to automatically connect to an ad-hoc network?

  - by George Edison

  I have two machines - one is running Ubuntu 12.04 64-bit and the other is running Windows 7 Starter Edition (32-bit). The Ubuntu machine is connected to the Internet via the eth0 interface. That machine also has a wireless network interface (wlan0) that is currently functioning as an ad-hoc network. I can connect to the ad-hoc network just fine with the Windows machine but each time I wish to do so, I must manually initiate the connection and enter the password. Is there some way to instruct Windows to automatically connect to this network (an option I have for standard wireless networks but not ad-hoc networks)?

  Read the article

• DDWRT or similar as repeater in a network.

  - by Quantumplation

  I have a friend with sever connection issues due to her wireless router being on the bottom floor of her house, and the computer being a story or two away. I have several old Linksys routers lying about, one of which is currently running DDWRT for my network. Would it be a good idea (effective) to configure one of these routers as a wireless bridge of some kind in an intermediary floor to improve her connection? Is there any specific configuration beyond the standard DDWRT setup that I would need to do? Thanks for your help. =)

  Read the article

• Intermittent connection issues with atheros ar9285

  - by MrStatic

  I have an asus K50IJ which has an atheros ar9285 wifi chip. It has decided to start to randomly drop internet. Although the card doesn't seem to notice it has. It will show full signal instead of say 3 bars. I tried to look at the atheros site for the latest driver but they don't even offer driver downloads. I then checked the asus site and it doesn't even list that card in the downloads for this laptop. I run Windows 7 64bit. It will drop either every minute or once a day while I am doing intensive bandwidth usage and when I am just idling.

  Read the article

• Network Bridging for WiFi-to-Ethernet in linux

  - by shakaran

  It is possible Network Bridging for WiFi-to-Ethernet in linux instead of Ethernet-to-Ethernet? I have a CentOS 6.3 machine. I am using KVM and I want perform a brigde for virtualize more machines. This machine is connected only via wireless connection and it doesn't have a ethernet connection. So, I did a bridge over the WiFi interface like: # cat /etc/sysconfig/network-scripts/ifcfg-br0 DEVICE="br0" NM_CONTROLLED="yes" ONBOOT=yes TYPE=Bridge BOOTPROTO=none IPADDR=192.168.1.50 PREFIX=24 GATEWAY=192.168.1.1 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System br0" Then I edit my wireless conection like: # cat /etc/sysconfig/network-scripts/ifcfg-mywireless ESSID="mywireless" MODE=Managed KEY_MGMT=WPA-PSK WPA_ALLOW_WPA2=yes CIPHER_PAIRWISE=CCMP CIPHER_GROUP=CCMP TYPE=Wireless #BOOTPROTO=none #IPADDR=192.168.1.50 #PREFIX=24 #GATEWAY=192.168.1.1 #DNS1=8.8.8.8 #DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="Auto mywireless" UUID=874***** ONBOOT=yes LAST_CONNECT=1355923469 BRIDGE=br0 After, I restart the network: # /etc/init.d/network restart Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface Auto_mywireless: Error: Unknown connection: 874***** [FAILED] Bringing up interface br0: [ OK ] But as you can see, it show a error. My ifconfig output shows now: # ifconfig br0 Link encap:Ethernet HWaddr 6E:20:AD:CE:D8:AB inet addr:192.168.1.50 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6c20:adff:fece:d8ab/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:6393 (6.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:432 errors:0 dropped:0 overruns:0 frame:0 TX packets:432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:62433 (60.9 KiB) TX bytes:62433 (60.9 KiB) ra0 Link encap:Ethernet HWaddr 00:22:F7:2B:87:E5 inet addr:192.168.1.42 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:f7ff:fe2b:87e5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:46 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:487894880 (465.2 MiB) TX bytes:148136473 (141.2 MiB) virbr0 Link encap:Ethernet HWaddr 52:54:00:5B:30:9A inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:70 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:5838 (5.7 KiB) But this doesn't give internet connection and I loss access to 192.168.1.50. So, it is possible setup this networking bridge WiFi-to-Ethernet?

  Read the article

• How can I monitor network traffic in an all Mac home network?

  - by raiglstorfer

  I have an all Mac network consisting of an Airport Extreme, 1 MacPro, 1 Mac Mini, 2 MackBook Pros, 2 iPads, and 2 iPhones. The Mac Pro is connected directly to the Airport Extreme via Cat5 and the rest is all running via Wireless. Lately I've been getting prompted by Google to enter Capchas frequently. The message states that I might have software running on my network I'm not aware of. My wireless router is password protected using WPA2 Personal and I frequently change my password so I don't think someone is using the network from outside (but I've no way to confirm this). I'm looking for a relatively cheap (preferably open source) solution that would enable me to monitor and profile the network usage by machine and port. Can someone recommend a solution?

  Read the article

• 2 routers, both DHCP, no IP assigned

  - by piobyz

  I can't get DHCP to assign IP to my wireless devices. My network config is as follows: Nanostation5 Linksys WRT350N, which is connected with Nanostation via its INTERNET port. Nanostation: LAN IP Address: 192.168.1.20 WLAN IP Address: 192.168.0.79 Network Mode: Router and is getting its IP via DHCP from my ISP Netmask: 255.255.255.0 Gateway IP: 192.168.1.1 LAN Network settings: IP Address: 192.168.1.20 Netmask: 255.255.255.0 Enable NAT: YES ENABLE DHCP Server: YES Range 192.168.1.100 ~ 250 Netmask: 255.255.255.0 Enable DNS Proxy: YES Linksys: Internet Connection Type: DHCP Router IP: 192.168.2.1 Subnet Mask: 255.255.255.0 DHCP: Enabled Start IP: 192.168.2.100 ~ 120 Advanced Routing: NAT: Enabled What I can do is connecting manually with this config: IP: 192.168.2.101 Subnet Mask: 255.255.255.0 Router: 192.168.2.1 DNS: 192.168.1.20 Search domains: WRT350N I want to be able to connect to both routers independently(now its 192.168.1.20 for Nanostation, and 192.168.2.1 for Linksys) and connect any wireless device using DHCP. What should be IP ranges, masks, etc. on both devices?

  Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >