Search Results

Search found 3127 results on 126 pages for 'lexical scope'.

Page 94/126 | < Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >

• NFS high CPU usage

  - by user269836

  Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

  Read the article

• Fresh Proxmox VE 2.1 installation with defaults can't be reached or pinged

  - by Damainman

  I am using the lastest Proxmox VE 2.1. My server has two NICS with a uplink only connected into eth0. My Server is a co-located server utilizing public IPv4 IPs. It is not behind a firewall or any system which monitors traffic. Via IPKVM I did a fresh install of Proxmox, I put in the correct IP, Mask, Gateway, and DNS information. The install went perfectly fine with no errors. Upon completion and rebooting the system: I am unable to reach the web GUI via the browser, it just times out. I am unable to ping the server. I am unable to ping outside to the Internet from within the server. Tried pinging out to 4.2.2.2 and yahoo.com I tried rebooting the server and restarting the network service. IFCONFIG shows my IP information under vmbro0 which also has the same MAC address as the eth0 device. eth0 only displays a IPv6 Scope:Link address, which I did not setup myself. This is my first time installing proxmox, but after searching for a few hours it doesn't seem like anyone else is having the same issue as me from a fresh install with just the defaults. So far the only thing I did was install it. Also, I know the network cable is good and the IP is good because I was running a Xen XCP server with the same network settings prior to wiping it to install proxmox. Some additional information: for pveversion -v (Installed proxmox-ve_2.1-f9b0f63a-26.iso) pve-manager: 2.1-1 (pve-manager/2.1/f9b0f63a) running kernel: 2.6.32-11-pve proxmox-ve-2.6.32: 2.0-66 netstat -nr (note: .136 is my network, and .137 is my gateway) Destination - Gateway - Genmask xxx.xxx.xxx.136 - 0.0.0.0 - 255.255.255.248 0.0.0.0 - xxx.xxx.xxx.137 - 0.0.0.0 /etc/network/interfaces auto lo iface lo inet loopback auto vmbr0 iface vmbr0 inet static address xxx.xxx.xxx.138 netmask 255.255.255.248 gateway xxx.xxx.xxx.137 bridge_ports eth0 bridge_stp off bridge_fd 0

  Read the article

• NTOP gives warnings on startup

  - by FR6

  I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

  Read the article

• virtualisation with kvm: export services from guest to the host

  - by ascobol

  Hello, I would like to export some services from the guest os to the host os, via kvm, and by the same way learn some things about networking. I have tried the following commands: In the host (kubuntu 10.4): $ sudo tunctl -u ascobol Set 'tap0' persistent and owned by uid 2401 $ sudo ifconfig tap0 192.168.2.1 netmask 255.255.255.0 broadcast 192.168.2.255 The ifconfig command returns: $ /sbin/ifconfig tap0 Link encap:Ethernet HWaddr 3e:4e:e3:cc:bc:92 inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::3c4e:e3ff:fecc:bc92/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:17 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 Then I run the virtual machine (ubuntu server 10.4): $ sudo kvm -hda ubuntuserver104.qcow2 -net nic -net tap,name=tap0,script=no (I'm using sudo because without it fails with the following message:) warning: could not configure /dev/net/tun: no virtual network emulation With sudo the virtual machine boots, I just get this message: pci_add_option_rom: failed to find romfile "pxe-rtl8139.bin" In the virtual machine: $ ifconfig eth0 192.168.2.2 netmask 255.255.255.0 broadcast 192.168.2.255 Now if I run: $ ssh 192.168.2.2 I just get a No route to host What is wrong with this setup ? Thanks !

  Read the article

• CryptSvc not matched by Windows 7 Firewall rule

  - by theultramage

  I am using Windows Firewall in conjunction with a third-party tool to get notified about new outbound connection attempts (Windows Firewall Notifier or Windows Firewall Control). The way these tools do it is by setting the firewall to deny by default, and to add an auditing policy to log blocked connections into the Security event log. Then they watch the log, and display notification about newly added entries. netsh advfirewall set allprofiles firewallpolicy blockinbound,blockoutbound auditpol /set /subcategory:{0CCE9226-69AE-11D9-BED3-505054503030} /failure:enable With this configuration in place, I now need to craft outbound allow rules for applications and system services. Here is the rule for CryptSvc, the service frequently used for certificate validation and revocation checking: netsh advfirewall firewall add rule name="Windows Cryptographic Services" action=allow enable=yes profile=any program="%SystemRoot%\system32\svchost.exe" service="CryptSvc" dir=out protocol=tcp remoteport=80,443 The problem is, this rule does not work. Unless I change the scope to "all programs and services" (which is really unhealthy), connection denied events like the following will keep appearing in the security log: Event 5157, Microsoft Windows security auditing. The Windows Filtering Platform has blocked a connection. Application Information: Process ID: 1476 (<- svchost.exe with CryptSvc and nothing else) Application Name: \device\harddiskvolume1\windows\system32\svchost.exe Network Information: Direction: Outbound Source Address: 192.168.0.1 Source Port: 49616 Destination Address: 2.16.52.16 Destination Port: 80 Protocol: 6 (<- TCP) To make sure it's CryptSvc, I have let the connection through and reviewed its traffic; I also configured CryptSvc to run in its own svchost instance to make it more obvious: ;sc config CryptSvc type= share sc config CryptSvc type= own So... why is it not matching the firewall rule, and how to fix that?

  Read the article

• Why won't dhclient use the static IP I'm telling it to request?

  - by mike

  Here's my /etc/dhcp3/dhclient.conf: request subnet-mask, broadcast-address, time-offset, routers, domain-name, domain-name-servers, domain-search, host-name, netbios-name-servers, netbios-scope, interface-mtu; timeout 60; reject 192.168.1.27; alias { interface "eth0"; fixed-address 192.168.1.222; } lease { interface "eth0"; fixed-address 192.168.1.222; option subnet-mask 255.255.255.0; option broadcast-address 255.255.255.255; option routers 192.168.1.254; option domain-name-servers 192.168.1.254; } When I run "dhclient eth0", I get this: There is already a pid file /var/run/dhclient.pid with pid 6511 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/eth0/00:1c:25:97:82:20 Sending on LPF/eth0/00:1c:25:97:82:20 Sending on Socket/fallback DHCPREQUEST of 192.168.1.27 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.27 from 192.168.1.254 bound to 192.168.1.27 -- renewal in 1468 seconds. I used strace to make sure that dhclient really is reading that conf file. Why isn't it paying attention to my "reject 192.168.1.27" and "fixed-address 192.168.1.222" lines?

  Read the article

• Dynamic ARP Entries turning into Static ARP entries

  - by Zach

  I recently acquired a client that has a strange ARP caching issue on one of thier servers. I have a server that will eventually start turning it's dynamic ARP entries into static ARP entries. This causes problems because when the machine that has a static ARP entries on this server receives a new IP via DHCP, then the server is not able to communicate with the clients. Clearing the ARP cache resolves the issue and the server is fine for about a week and then it starts slowly turning ARP entries into static ARP entries. I haven't narrowed it down to when or how many it starts to do, but slowly you start seeing 1 static ARP and then 5 and then 10. The server in question is a Windows Server 2003 SP2. It is a DC, DHCP, and DNS server. I've checked the DHCP scope options and there's nothing in there that would indicate anything to do with static ARP entries. The only thing different between this DNS server and our other DNS server is that the 'Dynamically Update DNA A and PTR records for DHCP clients that do not request updates' is checked on the problematic server. I've done a bit of research about this and it seems that this may happen if any PXE type services are running, from what I can tell, there is nothing running a PXE server. I'm a bit lost as I have never seen dynamic ARP entries start to turn into static ARP entries. Right now my solution is a schedule task that runs every 24 hours to clear the ARP cache (arp -d *). I would like to not rely on this schedule task. Has anybody seen this before or have any suggestions on how to troubleshoot this?

  Read the article

• windows clients cannot get dns resolution until you open and close ipv4 properties page

  - by GC78

  This strange problem has started recently. Some windows clients cannot seem to get dns resolution to the internet after boot, and sometimes again at some point in the day. Internal hosts are also slow to resolve. trying to ping an interal host by name will take a long time for the hostname to resolve to ip address and trying to ping a website by name will fail to resolve. If you go into the tcp/ip v4 properties and view but not change anything, ok/close out of that then the client starts working fine, hostnames will resolve quickly. I have seen this happen on both Vista and W7 clients. ipconfig /all at a client experiencing this problem shows everything in order. proper ip addr, gateway, dns server, dns suffix ect.. ipconfig /dnsflush will not fix them, neither will /release and /renew the clients get their ip address, mask and dns server info from either one of 2 OES dhcp servers that assign addresses in different scopes in the same subnet. the internal dns server is a different OES dns server the default gateway is not assigned by the OES server but is statically put in at the client (only for those who need to get to the Internet for their job) flat network topology What can I do to get to the bottom of this? It only happens to a few of the client machines and typically the same ones. It started happening when we made a change to one of the DHCP scopes in iManager. Strangly this problem only happens to clients that get an IP address from the scope that we didn't make any changes to.

  Read the article

• VBScript Capture StdOut from ShellExecute

  - by Joe

  I am trying to run the following code snippet as part of a tool to gather and log some pertinent system diagnostics. The purpose of this snippet is to gather the result of running the command: vssadmin list writers The snippet is as follows: ' Set WshShell = CreateObject("WScript.Shell") ' WScript.Echo sCurPath & "\vsswritercheck.bat" ' Set WshShellExec = WshShell.Exec("elevate.cmd cmd.exe /c " & sCurPath & "\vsswritercheck.bat") Set oShell = CreateObject("Shell.Application") oShell.ShellExecute "cmd.exe", sCurPath & "\vsswritercheck.bat", , "runas", 1 vsswriter = VSSWriterCheck Select Case oShell.Status Case WshFinished strOutput = oShell.StdOut.ReadAll Case WshFailed strOutput = oShell.StdErr.ReadAll End Select WScript.Echo strOutPut vsswriter = strOutPut With the first code snippet (commented out) I can run the command and capture stdout from the batch file. In the second code snipped, I cannot capture stdout. I need to be able to run the batch script with Elevated permissions, so I am looking for a compromise between the functionality of the two. I cannot run the entire calling script in elevated mode due to restrictions from other pieces of functionality. I am looking for any ideas on how to add this output to my log as I am running out of options that are within the scope of basic scripts.

  Read the article

• FreeBSD 8.1 unstable network connection

  - by frankcheong

  I have three FreeBSD 8.1 running on three different hardware and therefore consist of different network adapter as well (bce, bge and igb). I found that the network connection is kind of unstable which I have tried to scp some 10MB file and found that I cannot always get the files completed successfully. I have further checked with my network admin and he claim that the problem is being caused by the network driver which cannot support the load whereby he tried to ping using huge packet size (around 15k) and my server will drop packet consistently at a regular interval. I found that this statement may not be valid since the three server is using three different network drive and it would be quite impossible that the same problem is being caused by three different network adapter and thus different network driver. Since then I have tried to tune up the performance by playing around with the /etc/sysctl.conf figures with no luck. kern.ipc.somaxconn=1024 kern.ipc.shmall=3276800 kern.ipc.shmmax=1638400000 # Security net.inet.ip.redirect=0 net.inet.ip.sourceroute=0 net.inet.ip.accept_sourceroute=0 net.inet.icmp.maskrepl=0 net.inet.icmp.log_redirect=0 net.inet.icmp.drop_redirect=1 net.inet.tcp.drop_synfin=1 # Security net.inet.udp.blackhole=1 net.inet.tcp.blackhole=2 # Required by pf net.inet.ip.forwarding=1 #Network Performance Tuning kern.ipc.maxsockbuf=16777216 net.inet.tcp.rfc1323=1 net.inet.tcp.sendbuf_max=16777216 net.inet.tcp.recvbuf_max=16777216 # Setting specifically for 1 or even 10Gbps network net.local.stream.sendspace=262144 net.local.stream.recvspace=262144 net.inet.tcp.local_slowstart_flightsize=10 net.inet.tcp.nolocaltimewait=1 net.inet.tcp.mssdflt=1460 net.inet.tcp.sendbuf_auto=1 net.inet.tcp.sendbuf_inc=16384 net.inet.tcp.recvbuf_auto=1 net.inet.tcp.recvbuf_inc=524288 net.inet.tcp.sendspace=262144 net.inet.tcp.recvspace=262144 net.inet.udp.recvspace=262144 kern.ipc.maxsockbuf=16777216 kern.ipc.nmbclusters=32768 net.inet.tcp.delayed_ack=1 net.inet.tcp.delacktime=100 net.inet.tcp.slowstart_flightsize=179 net.inet.tcp.inflight.enable=1 net.inet.tcp.inflight.min=6144 # Reduce the cache size of slow start connection net.inet.tcp.hostcache.expire=1 Our network admin also claim that they see quite a lot of network up and down from their cisco switch log while I cannot find any up down message inside the dmesg. Have further checked the netstat -s but dont have concrete idea. tcp: 133695291 packets sent 39408539 data packets (3358837321 bytes) 61868 data packets (89472844 bytes) retransmitted 24 data packets unnecessarily retransmitted 0 resends initiated by MTU discovery 50756141 ack-only packets (2148 delayed) 0 URG only packets 0 window probe packets 4372385 window update packets 39781869 control packets 134898031 packets received 72339403 acks (for 3357601899 bytes) 190712 duplicate acks 0 acks for unsent data 59339201 packets (3647021974 bytes) received in-sequence 114 completely duplicate packets (135202 bytes) 27 old duplicate packets 0 packets with some dup. data (0 bytes duped) 42090 out-of-order packets (60817889 bytes) 0 packets (0 bytes) of data after window 0 window probes 3953896 window update packets 64181 packets received after close 0 discarded for bad checksums 0 discarded for bad header offset fields 0 discarded because packet too short 45192 discarded due to memory problems 19945391 connection requests 1323420 connection accepts 0 bad connection attempts 0 listen queue overflows 0 ignored RSTs in the windows 21133581 connections established (including accepts) 21268724 connections closed (including 32737 drops) 207874 connections updated cached RTT on close 207874 connections updated cached RTT variance on close 132439 connections updated cached ssthresh on close 42392 embryonic connections dropped 72339338 segments updated rtt (of 69477829 attempts) 390871 retransmit timeouts 0 connections dropped by rexmit timeout 0 persist timeouts 0 connections dropped by persist timeout 0 Connections (fin_wait_2) dropped because of timeout 13990 keepalive timeouts 2 keepalive probes sent 13988 connections dropped by keepalive 173044 correct ACK header predictions 36947371 correct data packet header predictions 1323420 syncache entries added 0 retransmitted 0 dupsyn 0 dropped 1323420 completed 0 bucket overflow 0 cache overflow 0 reset 0 stale 0 aborted 0 badack 0 unreach 0 zone failures 1323420 cookies sent 0 cookies received 1864 SACK recovery episodes 18005 segment rexmits in SACK recovery episodes 26066896 byte rexmits in SACK recovery episodes 147327 SACK options (SACK blocks) received 87473 SACK options (SACK blocks) sent 0 SACK scoreboard overflow 0 packets with ECN CE bit set 0 packets with ECN ECT(0) bit set 0 packets with ECN ECT(1) bit set 0 successful ECN handshakes 0 times ECN reduced the congestion window udp: 5141258 datagrams received 0 with incomplete header 0 with bad data length field 0 with bad checksum 1 with no checksum 0 dropped due to no socket 129616 broadcast/multicast datagrams undelivered 0 dropped due to full socket buffers 0 not for hashed pcb 5011642 delivered 5016050 datagrams output 0 times multicast source filter matched sctp: 0 input packets 0 datagrams 0 packets that had data 0 input SACK chunks 0 input DATA chunks 0 duplicate DATA chunks 0 input HB chunks 0 HB-ACK chunks 0 input ECNE chunks 0 input AUTH chunks 0 chunks missing AUTH 0 invalid HMAC ids received 0 invalid secret ids received 0 auth failed 0 fast path receives all one chunk 0 fast path multi-part data 0 output packets 0 output SACKs 0 output DATA chunks 0 retransmitted DATA chunks 0 fast retransmitted DATA chunks 0 FR's that happened more than once to same chunk 0 intput HB chunks 0 output ECNE chunks 0 output AUTH chunks 0 ip_output error counter Packet drop statistics: 0 from middle box 0 from end host 0 with data 0 non-data, non-endhost 0 non-endhost, bandwidth rep only 0 not enough for chunk header 0 not enough data to confirm 0 where process_chunk_drop said break 0 failed to find TSN 0 attempt reverse TSN lookup 0 e-host confirms zero-rwnd 0 midbox confirms no space 0 data did not match TSN 0 TSN's marked for Fast Retran Timeouts: 0 iterator timers fired 0 T3 data time outs 0 window probe (T3) timers fired 0 INIT timers fired 0 sack timers fired 0 shutdown timers fired 0 heartbeat timers fired 0 a cookie timeout fired 0 an endpoint changed its cookiesecret 0 PMTU timers fired 0 shutdown ack timers fired 0 shutdown guard timers fired 0 stream reset timers fired 0 early FR timers fired 0 an asconf timer fired 0 auto close timer fired 0 asoc free timers expired 0 inp free timers expired 0 packet shorter than header 0 checksum error 0 no endpoint for port 0 bad v-tag 0 bad SID 0 no memory 0 number of multiple FR in a RTT window 0 RFC813 allowed sending 0 RFC813 does not allow sending 0 times max burst prohibited sending 0 look ahead tells us no memory in interface 0 numbers of window probes sent 0 times an output error to clamp down on next user send 0 times sctp_senderrors were caused from a user 0 number of in data drops due to chunk limit reached 0 number of in data drops due to rwnd limit reached 0 times a ECN reduced the cwnd 0 used express lookup via vtag 0 collision in express lookup 0 times the sender ran dry of user data on primary 0 same for above 0 sacks the slow way 0 window update only sacks sent 0 sends with sinfo_flags !=0 0 unordered sends 0 sends with EOF flag set 0 sends with ABORT flag set 0 times protocol drain called 0 times we did a protocol drain 0 times recv was called with peek 0 cached chunks used 0 cached stream oq's used 0 unread messages abandonded by close 0 send burst avoidance, already max burst inflight to net 0 send cwnd full avoidance, already max burst inflight to net 0 number of map array over-runs via fwd-tsn's ip: 137814085 total packets received 0 bad header checksums 0 with size smaller than minimum 0 with data size < data length 0 with ip length > max ip packet size 0 with header length < data size 0 with data length < header length 0 with bad options 0 with incorrect version number 1200 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 300 packets reassembled ok 137813009 packets for this host 530 packets for unknown/unsupported protocol 0 packets forwarded (0 packets fast forwarded) 61 packets not forwardable 0 packets received for unknown multicast group 0 redirects sent 137234598 packets sent from this host 0 packets sent with fabricated ip header 685307 output packets dropped due to no bufs, etc. 52 output packets discarded due to no route 300 output datagrams fragmented 1200 fragments created 0 datagrams that can't be fragmented 0 tunneling packets that can't find gif 0 datagrams with bad address in header icmp: 0 calls to icmp_error 0 errors not generated in response to an icmp message Output histogram: echo reply: 305 0 messages with bad code fields 0 messages less than the minimum length 0 messages with bad checksum 0 messages with bad length 0 multicast echo requests ignored 0 multicast timestamp requests ignored Input histogram: destination unreachable: 530 echo: 305 305 message responses generated 0 invalid return addresses 0 no return routes ICMP address mask responses are disabled igmp: 0 messages received 0 messages received with too few bytes 0 messages received with wrong TTL 0 messages received with bad checksum 0 V1/V2 membership queries received 0 V3 membership queries received 0 membership queries received with invalid field(s) 0 general queries received 0 group queries received 0 group-source queries received 0 group-source queries dropped 0 membership reports received 0 membership reports received with invalid field(s) 0 membership reports received for groups to which we belong 0 V3 reports received without Router Alert 0 membership reports sent arp: 376748 ARP requests sent 3207 ARP replies sent 245245 ARP requests received 80845 ARP replies received 326090 ARP packets received 267712 total packets dropped due to no ARP entry 108876 ARP entrys timed out 0 Duplicate IPs seen ip6: 2226633 total packets received 0 with size smaller than minimum 0 with data size < data length 0 with bad options 0 with incorrect version number 0 fragments received 0 fragments dropped (dup or out of space) 0 fragments dropped after timeout 0 fragments that exceeded limit 0 packets reassembled ok 2226633 packets for this host 0 packets forwarded 0 packets not forwardable 0 redirects sent 2226633 packets sent from this host 0 packets sent with fabricated ip header 0 output packets dropped due to no bufs, etc. 8 output packets discarded due to no route 0 output datagrams fragmented 0 fragments created 0 datagrams that can't be fragmented 0 packets that violated scope rules 0 multicast packets which we don't join Input histogram: UDP: 2226633 Mbuf statistics: 962679 one mbuf 1263954 one ext mbuf 0 two or more ext mbuf 0 packets whose headers are not continuous 0 tunneling packets that can't find gif 0 packets discarded because of too many headers 0 failures of source address selection Source addresses selection rule applied: icmp6: 0 calls to icmp6_error 0 errors not generated in response to an icmp6 message 0 errors not generated because of rate limitation 0 messages with bad code fields 0 messages < minimum length 0 bad checksums 0 messages with bad length Histogram of error messages to be generated: 0 no route 0 administratively prohibited 0 beyond scope 0 address unreachable 0 port unreachable 0 packet too big 0 time exceed transit 0 time exceed reassembly 0 erroneous header field 0 unrecognized next header 0 unrecognized option 0 redirect 0 unknown 0 message responses generated 0 messages with too many ND options 0 messages with bad ND options 0 bad neighbor solicitation messages 0 bad neighbor advertisement messages 0 bad router solicitation messages 0 bad router advertisement messages 0 bad redirect messages 0 path MTU changes rip6: 0 messages received 0 checksum calculations on inbound 0 messages with bad checksum 0 messages dropped due to no socket 0 multicast messages dropped due to no socket 0 messages dropped due to full socket buffers 0 delivered 0 datagrams output netstat -m 516/5124/5640 mbufs in use (current/cache/total) 512/1634/2146/32768 mbuf clusters in use (current/cache/total/max) 512/1536 mbuf+clusters out of packet secondary zone in use (current/cache) 0/1303/1303/12800 4k (page size) jumbo clusters in use (current/cache/total/max) 0/0/0/6400 9k jumbo clusters in use (current/cache/total/max) 0/0/0/3200 16k jumbo clusters in use (current/cache/total/max) 1153K/9761K/10914K bytes allocated to network (current/cache/total) 0/0/0 requests for mbufs denied (mbufs/clusters/mbuf+clusters) 0/0/0 requests for jumbo clusters denied (4k/9k/16k) 0/8/6656 sfbufs in use (current/peak/max) 0 requests for sfbufs denied 0 requests for sfbufs delayed 0 requests for I/O initiated by sendfile 0 calls to protocol drain routines Anyone got an idea what might be the possible cause?

  Read the article

• Active Directory Child Domain Replication Problems

  - by MikeR

  Hi, I've recently inherited an Active Directory (all DCs Windows 2003) which has been configured with several child domains that are used as test environments for out CRM software. Two of these child domains have been used for testing using dates in the future (2015), throwing them well outside of the Kerberos tolerance for time, and they're flooding my event logs with replication errors such as the following: Description: The attempt to establish a replication link for the following writable directory partition failed. Directory partition: CN=Schema,CN=Configuration,DC=ad,DC=xxxxxxx,DC=com Source domain controller: CN=NTDS Settings,CN=TESTDC001,CN=Servers,CN=SiteName,CN=Sites,CN=Configuration,DC=ad,DC=xxxxxxx,DC=com Source domain controller address: 38e95b2a-35af-4174-84ba-9ab039528cce._msdcs.ad.xxxxxxx.com Intersite transport (if any): This domain controller will be unable to replicate with the source domain controller until this problem is corrected. User Action Verify if the source domain controller is accessible or network connectivity is available. Additional Data Error value: 5 Access is denied. I'd also like to upgrade to Windows 2008 at some point, but wouldn't want to attempt any schema updates while I'm not 100% confident on the replication. I'm guessing my only real solution will be to get rid of these child domains. The child domains are operating as stand alone domains, the DC is up and running and authenticating test users fine. I'm guessing the best solution to this would be to delete the domains (although I'd be happily told otherwise). The clock forwarding appears to have been happening for several years, so I'm assuming I can't just put the clock right (I'm guessing scope for this would be 180days, the same as the tombstone lifetime) With the replication errors would I be able to dcpromo the child domains DC, select it as the last domain controller in the domain and the child domain would be deleted? Or would I be better off treating the domain as an orphaned domain and use Microsoft's instructions to clear up as such. Any advice would be much appreciated.

  Read the article

• Workstations cannot see new MS Server 2008 domain, but can access DHCP. (solved)

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• Network problems with Ubuntu on VMware

  - by svick

  I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

  Read the article

• Why does my DSDT table is different from what I found online?

  - by Hao Shen

  I have found a field in DSDT table where I want to modify from here http://www.ztex.de/misc/c2ctl.e.html Generally, I want to modify the _PSS field about the processor so that I can have more frequency levels available in the CPUfreq driver interface. I try to use this command to dissemble the DSDT table from my Desktop(Linux2.6.29,Intel CORE 2): cat /proc/acpi/dsdt > dsdt.aml iasl -d dsdt.aml Then I have a file dsdt.dsl as following(very long, so I just show the beginning of the file): /* * Intel ACPI Component Architecture * AML Disassembler version 20090123 * * Disassembly of dsdt.aml, Mon May 6 20:41:40 2013 * * * Original Table Header: * Signature "DSDT" * Length 0x00003794 (14228) * Revision 0x01 **** ACPI 1.0, no 64-bit math support * Checksum 0x46 * OEM ID "DELL" * OEM Table ID "dt_ex" * OEM Revision 0x00001000 (4096) * Compiler ID "INTL" * Compiler Version 0x20050624 (537200164) */ DefinitionBlock ("dsdt.aml", "DSDT", 1, "DELL", "dt_ex", 0x00001000) { Method (DBIN, 0, NotSerialized) { Noop } Scope (\) { Device (_SB.VBTN) ................... But I can not find the _PSS field as shown in the website I have given above. I do not know why? I am sure the current cpufreq driver shows 4 frequency levels available. So at least there should be something in the table showing this..right? Has anybody here played with the DSDT table before? Thanks,

  Read the article

• Ubuntu second static IP, ifconfig, /etc/network/interfaces

  - by Schmoove

  I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

  Read the article

• Inconsistent DHCP replies with Windows 2008R2 DHCP server

  - by verbalicious

  I've got a Windows 2008R2 standard server running DHCP services. We've noticed that certain clients are receiving inconsistent DHCP replies. We have over 175 Windows workstations in this VLAN that don't seem to have trouble getting DHCP leases. However, PXE-booting clients trying to reach our DHCP server are able to get a lease inconsistently. Additionally, we tried using the "dhcping" tool against our DHCP server and found that roughly two of every three requests time out with "no answer" -- and this holds true when we set the timeout value on dhcping to 20seconds. After a failed attempt, however, we may get a dhcp lease reply immediately with dhcping. This leads me to believe that this issue isn't confined to PXE booting clients, but something more systemic with my LAN layer2 or DHCP. And that possibly my 175 windows clients are experiencing this in some form without my knowledge. We have over 30% of our scope available so the addresses are there. I was unable to find anything in the Windows server "DHCP-Server" log. Of course, my goal is to have my DHCP server reply to every request that it receives on the LAN!

  Read the article

• OpenLDAP replication fails, "syncrepl_entry: rid=666 be_modify failed (20)"

  - by Pavel

  I've configured a second host to replicate the main LDAP server via syncrepl in the slapd.conf: syncrepl rid=666 provider=ldaps://my-main-server.com type=refreshAndPersist searchBase="dc=Staff,dc=my-main-server,dc=com" filter="(objectClass=*)" scope=sub schemachecking=off bindmethod=simple binddn="cn=repadmin,dc=my-main-server,dc=com" credentials=mypassword When I restart slapd, it writes to /var/log/debug Jun 11 15:48:33 cluster-mn-04 slapd[29441]: @(#) $OpenLDAP: slapd 2.4.9 (Mar 31 2009 07:18:37) $ ^Ibuildd@yellow:/build/buildd/openldap2.3-2.4.9/debian/build/servers/slapd Jun 11 15:48:34 cluster-mn-04 slapd[29442]: slapd starting Jun 11 15:48:34 cluster-mn-04 slapd[29442]: null_callback : error code 0x14 Jun 11 15:48:34 cluster-mn-04 slapd[29442]: syncrepl_entry: rid=666 be_modify failed (20) Jun 11 15:48:34 cluster-mn-04 slapd[29442]: do_syncrepl: rid=666 quitting I've looked into the sources for the return code and found only #define LDAP_TYPE_OR_VALUE_EXISTS 0x14 in include/ldap.h. Anyway, I don't quite get what the error message means. Can you help me debugging this problem and figure out why the LDAP replication doesn't work? I've managed to put a "manual" copy via slapcat and slapadd into the database, but I'd like to sync automatically. UPDATE: "Solved" by removing /var/lib/ldap/* and re-importing the database with slapadd.

  Read the article

• Kickstart: Serve dynamic kickstart images via a CGI or PHP script?

  - by Stefan Lasiewski

  I'd like to kickstart a couple dozen RHEL6/SL6 servers. However, some of these servers are different and I don't want to create a new ks.cfg file for each class of server. Are there any products which can generate a Kickstart file dynamically on the fly, from a template? For example, if I append a line like this to the KERNEL: APPEND ks=http://192.168.1.100/cgi-bin/ks.cgi Then the script ks.cgi can determine what host this is (Via the MAC address), and print out Kickstart options which are appropriate for that host. I could optionally override some options by passing parameters to the script, like this: APPEND ks=http://192.168.1.100/cgi-bin/ks.cgi?NODETYPE=production&IP=192.168.2.80 After we kickstart the server, we activate Cfengine/Puppet on this system and manage the system using our favorite Configuration Management product. We're experimenting with xCAT but it is proving too cumbersome. I've looked into Cobbler, but I'm not sure it does this. Update: A roll-your-own solution is discussed in the O'Reilly book: Managing RPM-Based Systems with Kickstart and Yum, Chapter 3. Customizing Your Kickstart Install Dynamic ks.cfg, which echos some of the comments in this thread: To implement such a tool is beyond the scope of this Short Cut, but I can walk through the high-level design. Any such solution would mix a data store (the things that change) with a templating solution (the things that don’t change). The data store would hold the per-machine data, such as the IP address and hostname. You would also need a unique identifier, perhaps the hostname, such that you could pick up a given machine’s data. The data store could be a flat file, XML data, or a relational database such as PostgreSQL or MySQL. In turn, to invoke the system, you pass a machine’s unique identifier as a URL parameter. For example: boot: linux ks=http://your.kickstart.server/gen_config?host-server25 In this example, the CGI (or servlet, or whatever) generates a ks.cfg for the machine server25. But where, oh where, is the code for ks.cgi?

  Read the article

• PC won't PXE boot to WDS/MDT with Dell Optiplex 755

  - by Moman10

  I am trying to set up a basic MDT solution. I have set one up in the past at a previous job and it worked flawlessly, however here I'm running into a problem and am having no luck getting around it. I've installed Windows Server 2012 and MDT 2013, along with adding on the WDS role. I haven't configured much outside of the defaults for WDS, basically just set PXE response to respond to all clients (and unchecked admin approval). This machine does not run a DHCP server. I looked on the DHCP scope of our DHCP server, it shows options 66/67 checked and the server name of the WDS server is in there as well. I didn't add this but I assume it was put on during the install process (I believe I had to manually make some adjustments at my old job for this). The PC I have is a Dell Optiplex 755. I have enabled the onbard NIC w/PXE boot option in BIOS and attempted to boot. I get a "TFTP...." error but nothing offering out a DHCP address like I'm used to. In my previous job it pretty much worked right out of the box. I've verified that PortFast is enabled on the port and I've tried a couple different PCs (but both are the same model, only model I have to work with). No matter what, I get the same error. The subnet the PC is in is a different subnet than where the WDS server is sitting, but there are IP helper statements on the switch and the PCs can get regular DHCP addresses just fine from the DHCP server, just doesn't seem to get offered out a PXE boot option. I don't know if the problem is a configuration with the server or the PC itself...but after a few days of Googling I'm running out of ideas. Does anyone have a good idea of something it may be?

  Read the article

• Failing Windows Updates with Error Code 800719e4

  - by Kev

  On a number of Vista machines I have now come across the same error - when installing updates everything works fine, until it after it reboots and the rolls back during step 3. On all occasions (where a simple retry hasn't worked) the error code has been 800719e4. On my own laptop I have so far tried the following:- Installed the updates one by one manually - I started on the smallest and one by one have worked towards the largest one which has left me with "Security Update for Windows (KB2286198)" that refuses to install. Renamed all the files in "C:\Windows\Logs\CBS" to "xxx.old" where xxx was the original name with windows update turned off - no change Renamed all the folders in "C:\Windows\SoftwareDistribution" in the same manner - no change Attempted to install it manually "Windows6.0-KB2286198-x86.msu" - no change Tried to un-install IE8 - doesn't work, rolls back at the end (Installing the IE9 Beta when it launched was what alerted me to the issue on this laptop) Ran a "Fix It" thing from the Microsoft Website - no help (Can't find the link now). Tried to recover from the disk - but alas my laptop only has a recovery partition (and was unservice packed original). Ran with nothing running on startup, and only MS services - again no change. Google is being useless with a load of posts trying to get me to call a telephone number with letters in (presumably an American number) The error code appears to mean error log full but no one has any idea which log! The WinUpdate log does indicate the following is the error point though :- 2010-10-23 13:54:48:230 1240 738 Handler WARNING: Got extended error: "POQ Operation SetKeyValue OperationData \Registry\machine\Schema\wcm://Microsoft-Windows-shell32?version=6.0.6002.18287&language=neutral&processorArchitecture=x86&publicKeyToken=31bf3856ad364e35&versionScope=nonSxS&scope=allUsers\metadata\elements\HKEY_CLASSES_ROOT_lnkfile_shellex_DropHandler_defaultValue, @default, , ewAwADAAMAAyADEANAAwADEALQAwADAAMAAwAC0AMAAwADAAMAAtAEMAMAAwADAALQAwADAAMAAwADAAMAAwADAAMAAwADQANgB9AAAA" Has anyone any idea how to fix this once and for all - reinstalling laptop after laptop from scratch is mildly annoying at work where Office and Firefox are the only extras, but even more annoying at home - I don't fancy going through the palaver of reinstalling everything yet again.

  Read the article

• Change the order of IP addresses returned by ifconfig?

  - by erikcw

  I have an Ubuntu server with several IP addresses attached to it. 127.0.0.1 is listed as venet0 by ifconfig. I'm using Chef to configure the server. The problem is that chef is listing 127.0.0.1 as the IP address for the server instead of one of the server's "real" IPs. (apparent "ohai ipaddress" uses the first IP listed by ifconfig to determine the server's IP). How can I change the order so the servers main IP is listed first instead of the 127.0.0.1? Can venet0 be deleted and venet0:0 be "promoted" to take its place since 127.0.0.1 is already listed in the "lo" interface? lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16700 (16.7 KB) TX bytes:16700 (16.7 KB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:7622207 errors:0 dropped:0 overruns:0 frame:0 TX packets:8183436 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2102750761 (2.1 GB) TX bytes:2795213667 (2.7 GB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX1 P-t-P:XXX.XXX.XXX.XX1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX2 P-t-P:XXX.XXX.XXX.XX2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 route -n route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 0.0.0.0 255.255.255.255 UH 0 0 0 venet0 0.0.0.0 192.0.2.1 0.0.0.0 UG 0 0 0 venet0

  Read the article

• centos 6.3 kvm external ip forwarding to guests

  - by user1111702

  I have a centos 6.3 server with kvm installed. The server has 4 external ips and one NIC. 176.9.xxx.xx1 176.9.xxx.xx2 176.9.xxx.xx3 176.9.xxx.xx4 I use the following configuration ifcfg-eth0 as slave to ifcfg-br0 the configuration in ifcfg-eth0 is DEVICE=eth0 ONBOOT=yes BRIDGE=br0 HWADDR=14:da:e9:b3:8b:99 and in the ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=static BROADCAST=176.9.xxx.xxx IPADDR=176.9.xxx.xx1 NETMASK=255.255.255.0 SCOPE="peer 176.9.xxx.xxx" and I have 3 more aliases for br0 , br0:1 to get the trafic from the second external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx2 NETMASK=255.255.255.248 ONBOOT=yes br0:2 to get the trafic from the third external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx3 NETMASK=255.255.255.248 ONBOOT=yes br0:3 to get the trafic from the second external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx4 NETMASK=255.255.255.248 ONBOOT=yes The above settings work fine and I recieve the trafic from all the external ips. My problem is that I want to pass the trafic from external ip to specific virtual guest on my server. ie trafic that comes from 176.9.xxx.xxx2 must pass to virtual machine 1 176.9.xxx.xxx3 must pass to virtual machine 2 176.9.xxx.xxx4 must pass to virtual machine 3 Can you please help me how to achieve this ? What are the settings on the host and what should I do to the guests. Thank you in advance

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• NTOP gives warnings on startup

  - by FR6

  I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

  Read the article

• Win Svr 2003 DHCP Bad Addresses

  - by VinceM

  After looking at other posts I still can figure this out. I'll start at the beginning... I inherited this network and I'm not the most knowledgeable about networking... We have a AD DHCP Server that is also our DNS server, We were having some VPN issues (on the same server) and my boss decided to disable routing and remote access, which cleared the settings. We couldn't get it set back up correctly so we rolled back to a backup drive they created a number of months ago. Since rolling back I've had Bad_Address listings in DHCP and there is a number of duplicate records in the DNS Forward Lookup Zones. We have less than 50 devices on the network but I have over 90 Bad Addresses showing. This server is currently running but we get IP address conflicts all the time on pretty much all the computers. I have had people do release and renew but it didn't help... I have also deleted and re-added the scope to no avail either. Any help or ideas would be greatly appreciated and I apologize if I missed another post that has information to help. Thanks, Vince

  Read the article

< Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >