Search Results

Search found 4253 results on 171 pages for 'technical communications'.

Page 94/171 | < Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >

• Does a USB to RJ-45 console cable exist?

  - by Carl Flippin

  I am aware of the RJ-45 to DB9 adapter commonly used on cisco routers to access console. I am aware of the USB to DB9 adapters to allow laptops without serial to get a serial port. I am looking for a USB to RJ-45 adapter so I don't have to chain two adapters together. I have searched everywhere but even the pre-packaged solutions seem to have the two adapters chained together. Does such a thing exist? If it doesn't is there some technical reason it cannot? It seems like a manufacturer would just have to wire the DB9 end of the USB adapter differently and it would work just fine plugged straight into the console port of the router.

  Read the article

• Configure one IIS site to handle two separate SSL certificates using external Load Balancing or SSL Acceleration Servers

  - by bmccleary

  I have one web application on our server that needs to be referenced by two different domain names, both of which have their own SSL certificates. The application is exactly the same for both domains, but we have to keep the two domain names for legal reasons. The problem is that, since both domains need to have their own SSL certificate, that inside of our IIS 7.5 configuration we have to have two separate IIS applications (both pointing to the same physical location) with their own unique IP address and SSL certificate installed. Now, I know that, due to the nature of SSL communications, that this is by design and that you can't assign more than one SSL certificate per IP address and domain name. My question is… is there any way around this limitation and keep one web application in IIS and have it service two SSL certificates based on host name? I know that with the basic IIS configuration that this is not possible, but I was thinking that with some sort of combination of external load balancing and/or SSL acceleration servers/services that we could have these servers process the SSL request and leave IIS clean to have one single application. I am not familiar at all with these technologies, hence the reason I am asking if it is theoretically possible. If not, does anyone else know how to achieve this?

  Read the article

• Book recommendation for learning server management and Apache

  - by japancheese

  Hello, I'm currently managing a site that I feel could be optimized and utilized to be much faster, however, I'm having difficulty finding reliable information to do it. I find the Apache documentation to be a hard read, and too technical about things I don't have a strong grasp on. I'm just looking for a good beginner/intermediate book about server administration to learn as much as possible about Apache, as well as how to create a nice secure, robust server that doesn't crash at the first hint of unusual traffic surges. Thanks to anyone who can point me in the right direction.

  Read the article

• Which window manager do you use?

  - by Stephan202

  Combining "What is your default web browser?" and "What are the differences between Linux Window Managers", I ask you: which window manager do you use, and why? Myself I prefer a minimal window manager on the one hand (in the past I used Fluxbox), but on the other hand wish to go with the main stream, to ease finding (Googling) solutions in case of problems. Hence I stick with Gnome as it is shipped with Ubuntu. Why do you use the window manager which you use? I understand some reasons may be subjective, but please try to cite technical reasons where possible.

  Read the article

• How does one skip "Windows did not shut down successfully" in Win7-64?

  - by XenonofArcticus

  Migrating an app from an expensive and unreliable dedicated embedded x86 box running WinXP-embedded to COTS hardware (Dell E6410 laptop) running normal Win7-64. At this time, it's not feasible to deploy using Windows 7 embedded. The problem is, that the system is still sort of "embedded". The power could shut off at virtually any time without prior warning. We've stripped the OS down and removed the battery capability so that it will power down as desired. The app never writes to the disk, so it's not like we're going to corrupt anything terribly. The system is essentially idle after our app is up and running (with the exception of some computation, graphics, and TCP/IP and serial communications) so the OS enters a pretty stable state rather quickly. After a power-loss however, it rightly complains that Windows did not shut down successfully and presents the user with the Windows Error Recovery text screen. If left alone, it does eventually move on booting just fine, but we'd like to skip that step if possible. WinXP-embedded is designed to do this automatically, so I know it's possible. I've looked at the Kernel Switches but I didn't see anything documented for "Skip Windows Error Recovery". I've also read extensively on the startup process: http://homepage.ntlworld.com./jonathan.deboynepollard/FGA/windows-nt-6-boot-process.html I know I can disable the auto chkdsk in the registry, but that's not the same thing either. So, how do I streamline the boot process to not hassle the user about a situation that will be the regular normal situation?

  Read the article

• What was SPX from the IPX/SPX stack ever used for?

  - by Kumba

  Been trying to learn about older networking protocols a bit, and figured that I would start with IPX/SPX. So I built two MS-DOS virtual machines in VirtualBox, and got IPX communications working (after much trial and error). The idea being to get several old DOS games to run, link up to a multiplayer match, interact with each game window, and capture the traffic using Wireshark from the host machine. From this, I got Quake, Masters of Orion 2, and MechWarrior 2 to communicate back and forth. Doom, Doom2, Duke3d, Warcraft, and several others either buggered up under the VM or just couldn't see the other VM on the IPX network. What did I discover? None of the working games used SPX. Not even Microsoft's NET DIAG used SPX. They all ran ONLY on top of IPX. I can't even find SPX examples or use-cases of SPX traffic running over IEEE 802.3 Ethernet II framing. I did find references that it was in abundant use on token ring, but that's it. Yet any IPX-aware application that I've hunted down so far usually advertises itself as "IPX/SPX", which seems to be a bit of a misnomer, since it doesn't seem to use SPX. So what was SPX used for? Any DOS applications out there that use it which will run under my VM setup? Edit: I am aware that IPX is to SPX as IP is to TCP (layer 3 to layer 4), so I expected to see an SPX layer underneath the IPX layer in Wireshark when I ran my tests.

  Read the article

• A website hosted on the 1.0.0.0/8 subnet, somewhere on the Internet?

  - by Dave Markle

  Background I'm attempting to demonstrate, using a real-world example, of why someone would not want to configure their internal network on the 1.0.0.0/8 subnet. Obviously it's because this is not designated as private address space. As of 2010, ARIN has apparently allocated 1.0.0.0/8 to APNIC (the Asia-Pacific NIC), who seems to have begun assigning addresses in that subnet, though not in 1.1.0.0/16, 1.0.0.0/16, and others (because these addresses are so polluted by bad network configurations all around the Internet). My Question My question is this: I'd like to find a website that responds on this subnet somewhere and use it as a counter-example, demonstrating to a non-technical user its inaccessibility from an internal network configured on 1.0.0.0/8. Other than writing a program to sniff all ~16 million hosts, looking for a response on port 80, does anyone know of a directory I can use, or even better yet, does anyone know of a site that's configured on this subnet? WHOIS seems to be too general of a search for me at this point...

  Read the article

• Obsessive behaviors in sysadmins

  - by squillman

  I have been told by colleagues (mainly non-technical) that some of my admin behaviors border on / cross the line between normal and obsessive, which sometimes leads me to wonder how screwed up I really am (read "how screwed up everyone else really is"). What are your obsessive behaviors when it comes to your sysadmin tasks and job functions? What do you do religiously that would make you twitch if you didn't do it or that others just roll their eyes at? I have reasons for my actions. I want to prove to my coworkers that I'm not alone.

  Read the article

• Home Server restore fails cannot find boot device

  - by Tim Heuer

  I am using Windows Home Server to backup my PCs. I recently had a hard drive failure on one of my WHS connected PCs and obtained an identical sized/speed drive for my laptop. I used the latest home server restore CD and did the restore. It said it completed successfully. Upon reboot, it says 'cannot find boot device' and lists all my drives (hard drive, cd, network book) indicating no valid operating system was found. I boot using the Win7 repair disk and while it doesn't see the operating system, it sees the drive and if I go into a command prompt, I can see all my data on the drive. My laptop is Windows 7 64-bit Ultimate. I've tried most everything I can think of. I'm a technical user (software developer) so I'm pretty aware of how things work (or should). I don't feel like I'm missing a simple step here.

  Read the article

• How to prove that an email has been sent?

  - by bguiz

  Hi, I have a dispute on my hands in which the other party (landlord's real estate agent) dishonestly claims to not have received an email that I truly did send. My questions is, what are the ways to prove that the email was indeed sent? Thus far, the methods that I have already thought of are: Screenshot of the mail in the outbox Forwarding a copy of the original email I am aware of other things like HTTP/ SMTP headers etc that would exist as well. Are these useful for my purposes, and if so how do I extract these? The email in question was sent using Yahoo webmail ( http://au.mail.yahoo.com/ ). Edit: I am not seeking legal advice here, just technical advice as to how to gather this information.

  Read the article

• Installing SSL certs with nginx on Amazon EC2

  - by Ethan

  I finally got a cert from an authority and am struggling to get things working. I've created the appropriate combined certificate (personal + intermediate + root) and nginx is pointing to it. I got an elastic IP and connected it to my EC2 instance. My DNS records point to that IP. But when I point the browser to the hostname, I get the standard "Connection Untrusted" bit, with ssl_error_bad_cert_domain. Port 443 is open - I can get to the site over https if I ignore the warning. Weird thing is, under technical details, it lists the domain I tried to access as valid! When I try and diagnose with ssl testing sites, they don't even detect a certificate! What am I missing here? domain is yanlj.coinculture.info. Note I've got coinculture.info running on a home server without a dedicated IP and have the same problem, but I'll be moving that to the same EC2 instance as soon as I figure this thing out. I thought the elastic IP would solve things but it hasn't

  Read the article

• Explorer hijacked by a trojan

  - by hsdb

  I managed to catch a newish trojan that my Anti virus program wasn't able to detect. I'm usually not that bad at technical stuff regarding computers but I really don't know what to do with this one anymore. The trojan somehow managed to get my Windows to recover it every time I try to remove it by deleting it's exe (called some weird name located in Programs "asdza/saddasn.exe" (example only)). It also sets an entry in my autostart. It starts a second explorer.exe and tries to connect to some server obviously trying to steal data. (glad I still have my firewall) How can I get rid of this trojan, I really need help. It is new and probably unrecognized by all major virus scanners.

  Read the article

• Looking for ballpark pricing on an affordable a Cisco VOIP solution for our office

  - by guytech

  We have about 8 incoming PSTN lines that are currently on an old and antiquated Nortel Meridian ICS system. This system has been giving us some grief. We're looking for a new VOIP solution. I've been looking at a Cisco solution and it does seem pricey but I'm sure effective. Unfortunately, we probably can't afford a Cisco Unified Communications 520 which seems to be the ideal solution. We have about 15 people who need an extension and voicemail. We really don't have any need for a fancy system just an auto attendant of some sort when people call us. It looks like we'll have to get an older router and an addon card for what we're looking for to get best value pricing. However, I don't know a a lot about Cisco voice products so I'm a bit lost as to what to get. The only thing I am sure on is the pricing on VOIP phones which we expect to be about ~$100-200. However, I'm not sure what pieces of VOIP infrastructure to get. Any advice? I am familiar with Asterisk but right now I'm looking on pricing concerning a Cisco solution.

  Read the article

• Proxmox drbd configuration split brain [on hold]

  - by AudioDan

  I am planning a proxmox HA configuration with two Dell R710 machines (dual 6 core processors in each) with enterprise level drive raid arrays. I would be using DRBD with a quorum disk on a third machine. I would dedicate two 1GB nics on each server to the DRBD communications. We would have approximately 12 to 14 Virtual Machines running on this pair of servers. The proxmox manual recommends creating two DRBD resources - one for the Virtual Machines that normally run on ServerA and one for the Virtual Machines that normally run on ServerB. This is because of the Primary/Primary state in which this configuration runs. If both servers have VMs talking to the same DRBD resource and a split brain situation occurs, there is potential for data corruption that must be resolved. While I understand it would take more effort to create new virtual machines, can anybody foresee any potential problems with running a separate DRBD resource for each VM instead? Does anyone have experience running a setup that way and has it worked well? It seems to me that would allow more flexibility in moving machines back and forth.

  Read the article

• How realistic/easy is it to host our own web servers?

  - by morpheous

  It is increasingly looking like we will need to host our own servers, because we need modems physically attached to the server machines. I (think) we will need a T1 line to our office for starters. Dont know what else is involved other than the obvious redundancy and failover requirements. My questions are: Do we really have to do it our selves or can we find a service that allows the modems to be remote as well? If we have to host the servers ourselves, what are the steps (technical and operational) required?

  Read the article

• How to send from my Z88 to my PC

  - by Bevan

  I've got a Cambridge Z88 that I want to get working with my PC. Around 6 years ago - in 2004 - I made heavy use of my Z88 to do a whole bunch of writing on the train while commuting to and from work. The Z88 is solid state, lightweight and has a full size silent keyboard, so it works very well as a writing instrument. I still have the serial cable I soldered up back then and used successfully in 2004. It has these connections: Z88 9 pin ----- ------- 2 TxD ------> RxD 2 3 RxD <------ TxD 3 7 GND <-----> GND 5 4 RTS ------> CTS 8 5 CTS <-+ RTS 7 8 DCD <-+---- DTR 4 9 DTR ----+-> DCD 1 +-> DSR 6 Unfortunately, I haven't been able to find my notes from 2004 that describe how I got it to work back then. I've spent several hours trying to Google a result, but to no avail. I'm pretty sure the cable is fine - after all, it's what I used successfully six years ago, and I've checked it out with a multimeter - so I'm focusing on the PC end of things, which is where I'd like some assistance. Q1: In my recent attempts, I've been using both Hyperterminal (as built into Windows XP) and the command line (copy com2: con:), but with no success. What's a good (better!) serial communications application to use? Is there one that allows me to see as deep as the signalling that's occurring on the wire? Q2: If you have a Z88 that works correctly with your PC, what software do you use on the PC end, and what's the pinout of your cable? I'm pretty sure that the Z88 itself is working properly: When using the built in Import/Export tool to send a file, I see different behaviour when my serial cable is connected compared to disconnected. When disconnected, the transmission appears to work, with a progress meter counting up and then finishing; when connected, nothing happens 'cept a timeout if I wait long enough.

  Read the article

• What would you use to keep track of all the random information about your LAN/Enviroment?

  - by agnul

  Say you work in your average anarchy... no appointed IT guy, no Office-Manager whatsoever, just developers working in free-for-all mode and a couple of non technical people around for admin (non IT) stuff. What would you use to keep track of Hardware / Software inventory Backups of OS images, Drivers, and all that LAN configuration information Passwords for all the systems Currently I'm thinking of having some sort of wiki + web server on our only ''server-class'' machine, but then I fear I'd be the only one who would go through the hassle of adding information in the wiki... So, have you been through that? What would you suggest?

  Read the article

• Sendmail Alias for Nonlocal Email Account

  - by Mark Roddy

  I admin a server which is running a number of web applications for a software dev team (source control, bug tracking, etc). The server has sendmail running solely as a transport to the departmental email server over which I have no control. We have someone who is still in the department but no longer on the dev team so I need to configure the transport agent to redirect all outgoing email (which would be coming from these applications) to the person that has taken their place. I added an entry in /etc/aliases like such: [email protected]: [email protected] But when I run /etc/init.d/sendmail newaliases I get the following error: /etc/mail/aliases: line 32: [email protected]... cannot alias non-local names So clearly I'm doing something I shouldn't. Is there a way to get aliases to work with non-local names or alternatively is their a way to accomplish my goal of redirecting outgoing mail for this user to another one? Technical Specs if the matter: Ubuntu 6.06 sendmail 8.13 (ubuntu provided package)

  Read the article

• Standards for documenting/designing infrastructure

  - by Paul

  We have a moderately complex solution for which we need to construct a production environment. There are around a dozen components (and here I'm using a definition of "component" which means "can fail independently of other components" - e.g. an Apache server, a Weblogic web app, an ftp server, an ejabberd server, etc). There are a number of weblogic web apps - and one thing we need to decide is how many weblogic containers to run these web apps in. The system needs to be highly available, and communications in and out of the system are typically secured by SSL Our datacentre team will handle things like VLAN design, racking, server specification and build. So the kinds of decisions we still need to make are: How to map components to physical servers (and weblogic containers) Identify all communication paths, ensure all are either resilient or there's an "upstream" comms path that is resilient, and failover of that depends on all single-points of failure "downstream". Decide where to terminate SSL (on load balancers, or on Apache servers, for instance). My question isn't really about how to make the decisions, but whether there are any standards for documenting (especially in diagrams) the design questions and the design decisions. It seems odd, for instance, that Visio doesn't have a template for something like this - it has templates for more physical layout, and for more logical /software architecture diagrams. So right now I'm using a basic Visio diagram to represent each component, the commms between them with plans to augment this with hostnames, ports, whether each comms link is resilient etc, etc. This all feels like something that must been done many times before. Are there standards for documenting this?

  Read the article

• Encrypted WiFi with no password?

  - by Ian Boyd

  Is there any standard that allows a WiFi connection to be encrypted, but not require a password? i know that (old, weak) WEP, and newer WPA/WPA2 require a password (i.e. shared secret). Meanwhile my own wireless connections are "open", and therefore unencrypted. There is no technical reason why i can't have an encrypted link that doesn't require the user to enter any password. Such technology exists today (see public key encryption and HTTPS). But does such a standard exist for WiFi? Note: i only want to protect communications, not limit internet access. i get the sense that no such standard exists (since i'm pretty capable with Google), but i'd like it confirmed. Claraification: i want to protect communcations, not limit internet access. That means users are not required to have a password (or its moral equivalent). This means users are not required: to know a password to know a passphrase to enter a CAPTCHA to draw a secret to have a key fob to know a PIN to use a pre-shared key have a pre-shared file to possess a certificate In other words: it has the same accessibility as before, but is now encrypted.

  Read the article

• How to solve my black screen at boot?

  - by Juanillo

  I've got a friend with a weird problem. When he starts his computer the screen is completely black until the computer is completely started. So the screen is black until it suddenly shows the Windows desktop. He said that this is happening since a technical service repaired his computer, but that repair is not now in warranty. Recently the computer stopped working, but as the screen is black he cannot access to BIOS or start in safe mode (by pressing F8). When he inserts the Windows Vista DVD the system doesn't boot from DVD (it mustn't be configured in this way in the BIOS). Maybe there´s a problem with the hardware (maybe the graphic card)? Can anyone explain a reason why the screen is black during start-up? Any idea of what to do with the computer to restore it?

  Read the article

• Remove noise from a recording

  - by essamSALAH

  I used to record important technical meetings and demos using Camtasia Studio, using a Mic to capture the speaker voice. Sometimes we invite attendees by asking them to call us in the meeting, and they would call on a cell phone then we switch it to loudspeaker so we can hear and talk to them and also record the conversation on Camtasia. The problem I am having now is that playing back those recording produces the regular noise that results from the microphone being close to the mobile phone (the kind of noise you hear when your mobile phone rings and it is near a speaker). Any advice on removing this noise?

  Read the article

• How does one delete a directory filled with files and other subdirectory permanently, bypassing the trash, from the command line in OS X?

  - by Jon

  So my command line skills are a little rusty and I'm having trouble remembering the differences between the meanings of flags in different distro's os's. I also don't really remember all my technical lingo so manpages seem really unclear. Basically I'm on Mac OS X and want to delete a directory along with all of its contents. What I'm mainly concerned about, I suppose, is that it'll delete literally ALL of the references within the directory, including ../ and ../<everything else, including ../'s own ../> and then just totally screw up my entire system. Which of these do I want to run? $ rm -R dir-name/ or $ rm -r

  Read the article

• Is it possible to combine two internet connections to increase performance?

  - by cornjuliox

  I've got a small home network, 3 PCs plus a laptop or two when the relatives come to visit, connected to a single cable internet connection. Now, as soon as everyone starts using the 'net the performance starts to suffer and if the load is heavy enough nobody can get anything done and everyone complains. At one point it was so bad that only one of us could use it at a time. I was researching possible solutions to this problem and I heard that internet cafes that utilize 2 internet connections, possibly from different providers, and have some sort of router that allows them to split the traffic between the both of them, with online games going through one and web traffic going through another. Is this possible? What is the technical term for it, and can/should it be applied to a home network setup or is there another solution to this problem?

  Read the article

• How to make the jump from consumer support to enterprise support?

  - by Zac Cramer

  I am currently a high level consumer break/fix technician responsible for about 300-400 repairs a month. I am good at my job, but bored, and I want to move into the enterprise side of my company, dealing with Server 2008 R2 and exchange and switches and routers that cost more than I make in a month. How do I make this transition? Whats the best thing to learn first? Is there a standard trajectory for making this leap from consumer to business? I am full time employed, so going back to school is not a great option, but I have no life, so spending my nights and weekends reading and practicing is totally within my realm. I am basically overwhelmed by the number of things to learn, and looking for any advice you may have on the best way to proceed. PS - I apologize if this is a not quite the right forum for this, I know its not a technical question exactly, but I also know the sorts of people I want to answer this question are reading this website.

  Read the article

< Previous Page | 90 91 92 93 94 95 96 97 98 99 100 101  | Next Page >