Search Results

Search found 2774 results on 111 pages for 'adapter'.

Page 95/111 | < Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >

  • Why isn't my phone charging with some micro usb cables?

    - by Jacxel
    I ordered 3 microUSB cables over ebay. My phone was at about 50% battery and I wanted to use it as a hot spot for some browsing on my laptop, so I plugged it in, a charging icon appeared on the phone, my laptop showed it as a connected usb device and so I went about my business. About 30 minutes later I checked the phone and to my dismay saw 45% battery. But ahh, I thought, I have been putting the poor little thing under too much pressure, acting as a WiFi hotspot must drain the battery quicker than it can charge via usb, perhaps even using my laptops usb port wouldn't output enough power. Unscathed I continued on and when I was going to bed I plugged the usb cable into a mains adapter and switched everything battery consuming off and content, went to sleep. The next morning I was awoken by my phones alarm which got cut off unexpectedly. I attempted to unlock my phone which showed no more signs of life. Why isn't my phone charging with these new USB cables? For clarity: They transfer data with no problems The phone appears to be charging, showing all the signs and lights it normally would, the cable that came with the phone works as you would expect, so its not a fault with the phone, I think they slow the discharging of the phone, but I could be wrong. Are these just bad quality cables? Is there a way to fix this issue?

    Read the article

  • Alternative Bluetooth Stacks for Windows 7 64bit

    - by Martin
    I have a notebook with an inbuilt Broadcom BCM2046 bluetooth adapter and several bluetooth HID-devices (mice, keyboards etc.) The operating system is Windows 7 64 bit Professional. The HID-devices all work perfectly with other computers, but on the system mentionend above, problems with some power-saving features inside the HID-devices occur (see eg. Amazon reviews for Microsoft Mobile Keyboard 6000 not waking up). I have tried the bluetooth drivers supplied by Windows update and the latest Broadcom drivers directly from the Broadcom updater software. The problems persist (I can rule out any further configuration issues or alternative device drivers, I have tried every possibility). I have tried a trial version of the BlueSoleil Bluetooth stack and it solved the wake-up problem. However the BlueSoleil stack causes some other problems, is relatively expensive and I would prefer not to use it. My question: are there any other alternative bluetooth stacks availible for Windows 7 64bit? To my knowledge there used to be Toshiba Bluetooth stack for non-Toshiba hardware, but the older versions I have found on the internet do not install, they do not seem to recognize the bluetooth hardware when installing the driver.

    Read the article

  • RTNETLINK answers: File exists... maybe because assigned a new mac adress

    - by steven
    I got a "RTNETLINK answers: File exists Failed to bring up eth0:1" on "ifup eth0:1". I suspect it happens because i assigned a new mac adress in my VM's network adapter. Can you tell me how to fix the issue? My configuration looks like this: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 allow-hotplug eth0 iface eth0 inet static address 192.168.1.80 netmask 255.255.255.0 gateway 192.168.1.1 dns-nameservers 192.168.1.1 # Alias being connected to 192.168.10.x Network auto eth0:1 allow-hotplug eth0:1 iface eth0:1 inet static address 192.168.10.83 netmask 255.255.255.0 gateway 192.168.10.10 dns-nameservers 192.168.10.1 Why do I get "RTNETLINK answer: File exists.." suddenly? I worked with this configuration before without problems. All i did in the past is to renew the adapters mac adress. At the moment I am connected to the 192.168.10.x Network and if I do /etc/init.d/networking stop /etc/init.d/networking start then i got "RTNETLINK [...] falied to bring up eth0:1" but the strage thing is that i am able to connect to 192.168.10.83 via ssh from my host machine. But I cannot reach the internet from the debian client. I hope it is clear what my problem is, now. update if i change my /etc/network/interfaces like this then "ifup eth0" fails, too with the same error! # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 allow-hotplug eth0 iface eth0 inet static address 192.168.10.83 netmask 255.255.255.0 gateway 192.168.10.10 dns-nameservers 192.168.10.1 with verbose option enabled i got: Configuring interfache eth0=eth0 (inet) run-parts --verbose /etc/network/if-pre-up.d ip addr add 192.168.10.83/255.255.255.0 broadcast 192.168.10.255 dev eth0 label eth0 RTNETLINK answers: File exists Failed to bring up eth0. same if i type this manually: ip addr add 192.168.10.83/255.255.255.0 broadcast 192.168.10.255 dev eth0 label eth0

    Read the article

  • Wireless keeps shutting off in Windows 7

    - by Nathan Adams
    I have Windows 7 Ultimate 32bit installed on a Dell Latitude XT Tablet and for the life of me I can't figure out this really weird problem. The symptom is that the Wireless will disconnect from the AP and if I tell it to scan again, it says there are no APs in the area. I do have another wireless card in the laptop and if I disable the first one and enable the second, I am able to get onto the wireless however if I want to use the first card again I have to restart. I tried enabling/disabling the device, nothing will kick start the wireless again in the first card without a restart. I even tried different drivers. So, it seems it is random but it does occur more often when there is increased network activity (ie downloading a large file). The laptop doesn't seem to be overheating. I have tried the following: Under "Change Advanced Power Settings" for the current power profile, I set the "Wireless Adapter settings" to "Maximum Performance". Under device manger, I went to the card in question, and went to the advanced tab and set the "Power Saving mode" to "MAX_PSP" Both cards I have seem to exhibit the behavior after awhile. Both models of those cards are: Dell Wireless 1505 Draft 802.11n WLAN Mini-Card Gigabyte GN-WS30N 802.11n mini WLAN Card Has anyone have any ideas or ran into this before?

    Read the article

  • Finding Bluetooth link key in Windows 7, to double pair a device on dualboot computer

    - by Ilari Kajaste
    How can I dig up the Bluetooth link key for a paired device in Windows 7? Is this something that is dependent on the Bluetooth stack I'm using (Toshiba), or is there a generic place to store these in Windows 7? Note: I'm not talking about the six-digit code usually typed by the user during pairing - that is worthless since it's discarded after pairing process. What I mean is the 128-bit link key that the devices exchange during pairing, and use thereafter to encrypt all their Bluetooth traffic. Background: I dualboot Windows 7 / Ubuntu on my laptop, and I would like to have my phone paired to both OS's. Since the dualbooting computer has only one Bluetooth adapter and thus only one Bluetooth address, I cannot do two pairings to the phone, since on the second pairing (Windows) the phone just replaces the previous pairing (Linux) to the same Bluetooth address. A thread on Ubuntu forums pointed me to what I have to do - pair first on Linux, then on Windows, and then replace the link key on Linux side with the one Windows negotiated. I can find the Linux side pairing key from /var/lib/Bluetooth/[BD_ADDR]/linkkeys - no problems there. However, on Windows side I can't find the key. According to the forum post, on Windows side the key should be in SYSTEM\ControlSet002\services\BTHPORT\Parameters\Keys\[BD_ADDR] but while that registry key does exist, it has no subkeys. (And a similar registry path in ControlSet001 didn't have any subkeys either.) One thing I've been instructed to do is to capture all events during pairing with Sysinternals Process Monitor. I did this, but I haven't been able to find any useful information from the captured events, not even by exporting the data to a huge XML and grepping that with the BD_ADDRs (with or without colons). So how could I find the link key for a paired device in Windows 7? Some reference information: Wikipedia: Bluetooth, Security Now: Bluetooth security

    Read the article

  • Wifi antenna extension with F-connector/RG-6(RG-59) cable?

    - by rjz2000
    In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

    Read the article

  • Wifi antenna extension with F-connector/RG-6(RG-59) cable?

    - by rjz2000
    In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

    Read the article

  • How do you initialize networking on a new Xen guest VM?

    - by Marten Veldthuis
    We have a Citrix XenServer setup, and while I personally lean more towards Dev than Ops, I've got an issue that's been bugging me. When you provision a new (Linux/Ubuntu) guest, how do you get it to have the correct IP-address? I'd want my application servers to exist in the range of 10.20.0.0/24, preferably being .1, .2, etc, so I can keep my sanity. I guess that the actual IP-address is something set in Linux itself, and Xen can't touch that, but then what's the best practice for getting it done? If you set up DHCP, don't you just move the problem to getting the adapters the "correct" MAC-addresses? Do you just have to hardcode a large table of MAC-addresses to IP-addresses, and then provision new guests always with the correct MAC-address on the virtual ethernet adapter? What we currently do is have an image of a "app server" that we boot up a new instance of, and then finalize it (with a script) that (among other things) modifies the /etc/networking/interface file to give it the correct IP. But that feels dirty to me, and I feel like surely there must a better way. Please enlighten me?

    Read the article

  • How to setup firewall to allow internet connection sharing via Wifi USB stick?

    - by hannanaha
    I have a Windows8 computer linked to the internet via an ethernet cable ("Ethernet" network connection). I have attached to it a DLink Wifi USB stick, and I'm trying to share the main PC's internet connection with my Android phone via a local wifi network. I am using the following batch file to set up this network: netsh wlan set hostednetwork mode=allow ssid=MyWifiName key=password keyUsage=persistent netsh wlan start hostednetwork After I run this script, I can see a new network connection appear in "Control Panel\Network and Internet\Network Connections" named "Local Area Connection *12", and I can see "MyWifiName" on the Android phone. The device name for this connection on the PC is "Microsoft Hosted Network Virtual Adapter". I also set up the "Ethernet" connection to share Internet with "Local Area Connection *12". However, the Android phone usually doesn't manage to obtain an IP from the wireless network, and when it does, there still seems to be no connectivity to the internet. When I turn off the Windows Firewall completely, or even just for "Local Area Connection *12", the Android connection is perfect. My questions are: How should I set up the Windows firewall to allow the phone to connect properly? Is there a specific rule I need to add to the Windows firewall advanced settings? [Note: the above method worked great in Windows 7, without any specific tinkering with the firewall]. Is it safe to turn off the firewall specifically for the "Local Area Connection *12" (the wifi connection) if the main Ethernet connection is still protected by the firewall? Thanks in advance.

    Read the article

  • Intel Ethernet Bottlenecking Internet?

    - by Donald Darma
    I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

    Read the article

  • Ubuntu 12.10, Unity, AMD 12.11 beta drivers, AMD APP SDK 2.7 and OpenCL detection of multiple gpus

    - by junkie
    I'm using Ubuntu 12.10, AMD 12.11 beta drivers, AMD APP SDK 2.7 and OpenCL. I have three amd radeon 7990s plugged in each of which are a dual 7970 so I have six gpus altogether. I plan to go up to eight in a few days. Windows couldn't use even 4 but linux works fine with 6 so far. The strange thing is that the six gpus are only detected by OpenCL in unity (the ubuntu default window manager). If I switch to e17, blackbox or fluxbox or anything else for that matter OpenCL only detects one. I'm using a simple OpenCL program to list all devices to check. I've also checked the output of aticonfig --list-adapters, fglxinfo and clinfo. The first two always show six in all window managers wheras clinfo shows 6 in unity but 1 gpu in all other WMs. I'm also using an X config generated by aticonfig --initial -f --adapter=all. I'm also only using one monitor. I've also checked using lsmod that the fglrx module is loaded in all WMs. So I have two questions. Why does OpenCL see six gpus only in unity? How can I enable six gpus on other lightweight WMs? Basically I'm getting at what determines how many gpus the OpenCL runtime sees? Thanks.

    Read the article

  • PC -> TV HDMI suddenly doesn't work, any other option does

    - by XSlicer
    So my parents wanted to connect their PC to their TV, so they bought a 10m (35 ft) cable. It all worked perfectly. Then my mom tripped over the cable, breaking it. She somehow got a free replacement, but at the same time some more expensive one from an uncle. Now the problem is that this suddenly doesn't work anymore (TV saying "Format not supported"). I've tried several other things to pinpoint the actual problem, but none brought me something conslusive: PC (hdmi) to TV doesn't work (both cables) PC (hdmi) to TV doesn't work (short cable) Laptop (hdmi) to TV work (same cables) BluRay (hdmi) to TV works (same cables) PC (hdmi) to monitor works (same cables) PC (DVI w/ adapter HDMI) to TV works (same cables) I've tried different ports, tried Linux, reinstalling drivers (the graphics card is internal using an i5 sandy bridge. Normally it's running Windows 7 Home Prem, the TV being a Philips 37PFL7605H). So basically, everything works, except that thing what we want. The only things I am thinking of is that the sound is interfering or that the HDMI-output is somehow broken. Or is it anything else? I'm kind of lost.

    Read the article

  • How to diagnose storage system scaling problems?

    - by Unknown
    We are currently testing the maximum sequential read throughput of a storage system (48 disks total behind two HP P2000 arrays) connected to HP DL580 G7 running RHEL 5 with 128 GB of memory. Initial testing has been mainly done by running DD-commands like this: dd if=/dev/mapper/mpath1 of=/dev/null bs=1M count=3000 In parallel for each disk. However, we have been unable to scale the results from one array (maximum throughput of 1.3 GB/s) to two (almost the same throughput). Each array is connected to a dedicated host bust adapter, so they should not be the bottleneck. The disks are currently in JBOD configuration, so each disk can be addressed directly. I have two questions: Is running multiple DD commands in parallel really a good way to test maximum read throughput? We have noticed very high SWAPIN-% numbers in iotop, which I find hard to explain because the target is /dev/null How shoud we proceed in trying to find the reason for the scaling problem? Do you thing the server itself is the bottleneck here, or could there be some linux parameters that we have overlooked?

    Read the article

  • Slow browsing through IE on Windows Server 2012

    - by Volodymyr
    We've run into strange issue on the freshly installed servers. H/W: IBM server X3550 M4 7914; OS: Windows Server 2012 Std. Then we try to browse on the servers thru IE, not all sites are opened or it takes too long time to open the page, i.e. very few of them can be opened. Local FW are disabled. Servers are in a new subnet and traffic is allowed for it. VLAN is configured properly Another Windows Server 2012 host is running OK and Internet access works fine, but it is VM running on Hyper-V 2012. No proxy is used on the network. At the same time, if one tries to establish telnet session to any site on 80/443 ports - it does work. Google works as well. I've tried to configure single Qlogic adapter to check if the issue remains - it does. Teaming is configured with the means of QLogic, not by built-in functionality. IE Enhanced Security is disabled. IE settings were reset, more than once. Why would certain sites work while others not - Idk. I also tried to disable ecncapability and restart server - no luck netsh int tcp set global ecncapability=disabled Any thoughts? UPD1 VMQ is disabled. Servers are not running Hyper-V. UPD2 Servers were rebuilt from scratch, got a mail a few mins ago. Issue still remains. Teaming is now configured with the means of Windows Server 2012.

    Read the article

  • Ubuntu 12.10 64bit host reboots when trying to install any guest system using VirtualBox

    - by gts123
    I am having a really nasty problem with VirtualBox as everytime I try to install any guest OS(using ISO file as CD for installation media), the installation starts normally but as soon as it is about to start either installing to virtual hard drive or loading(e.g. as LiveFS) it causes the host system to reboot abruptly. Config is as below: Host system: Ubuntu 12.10 64bit - Intel® Core i7-2640M CPU @ 2.80GHz × 4 Virtualbox version: 4.1.18_Ubuntu r78361 Guest OS systems tried: 32bit version of FreeBSD 9, Debian 6, Tails 0.14 VM setup Tried to have the minimal setup necessary just in case it would avoid for each system to make sure I'd avoid conflicts, but to no avail. I've tried different values and combinations of the below but the problem still persists: Shared Clipboard: Disabled Show in fullscreen/seamless: Disabled Remember runtime changes: DIsabled Base Memory: 2048 MB Chipset: PIIX3 IO APIC: Disabled EFI: Disabled Absolute Pointing device: Disabled Processor(s): 1 CPU PAE/NX: Disabled VT-x/AMD-V: Disabled Video Memory: 12 MB 3d/2d acceleration: Disabled Storage IDE COntroller: PIIX3 (same as chipset instead of PIIX4) Use host I/O cache: No Audio: disabled Network adapter: NAT USB controller: disabled No shared folder Also another sideeffect of the reboot is that it appears that it does not log any information in the error log files; not making things any easier. Please help.

    Read the article

  • RouterLess, house-wired network using multiple powerline adapters

    - by Cliff Arnell
    related to the 'old days' of one ethernet cable tapped with Ts for each monitor.... my question might be very simple... or not. I have an over-the-air internet provider with a wire dish with a powered transceiver and cat5 cable out of the providers supplied modem. I'm presently connecting the output of the modem into my wireless router which sends the internet signal all over the house. Standard stuff, I believe. My Question. Can I just connect the output of the modem into 1 powerline adapter and tie all my equipment such as computer, printer, laptop, Tivo recorder, etc. into 1-each local powerline adapters located near each devices resulting in a 'house-wired' network and no router? I'm bothered by the idea that my over-the-air provider might be using something in my router to establish and keep my IP connection alive. I did have to configure the router for my IP, a router which, in my proposed scenario, would no longer exist. Thank you for your help.

    Read the article

  • I need a driver for my Cardbus USB 2.0 card

    - by Carl
    The picture and details of the card are here: http://www.ht-link.com/en/ProductView.asp?ID=106 The Windows drivers for this don't work right. I tried them on my previous laptop, and then installed the ones off their included CD. (Note that the systems requirements includes a CD-ROM drive...) I have a new laptop, and lost the CD. The website that lists the drivers is broken - the download links don't work. It is here: http://www.ht-link.com/en/DownView.asp?ID=10 I need the very first link - The Win XP drivers for the HT-112NEC. The company does not reply to my e-mails. I've tried searching Google for other sources for the driver (I didn't bother with those sites that want me to install driver detection software or create a log-in for their site). [Here's the problem I am getting using the drivers Windows XP SP3 installs: When I plug in my USB 2.0 hard-disk adapter, a USB Mass Storage Device entry is added in the Device Manager, but there is no entry under Disk Drives, and a drive letter is not assigned, so I can't access the driver. Like I said, this card didn't work without their special drivers on my other laptop, either.]

    Read the article

  • Does ICS modify windows firewall policies in the registry?

    - by insipid
    I had a host machine I wanted to enable ICS on. First I realized that doing so was not possible until I enabled the Windows Firewall. Once I enabled the firewall and set up ICS, I noticed due to group policy I could no longer disable the firewall. Also, any ports I tried to open seemed to be ignored. Although nothing seemed to be configured when I used the mmc snap-in to view local computer policy, when I checked the registry I noticed several policies set there in HKLM (such as disabling AllowLocalPolicyMerge). I was able to remove the policies from the registry and my open ports worked, but they were eventually re-added without my input. The network I am sharing the internet from is an "unsecured" wireless network with an authentication page, is it possible that this is causing those policies to be set? Did ICS set those policies? When you go to the properties of the ICS enabled adapter and go to the ICS settings it takes you to a tab called services where you can add and remove "services running on your network that internet users can access". Is this related to the windows firewall?

    Read the article

  • How can I pair two bluetooth dongles together?

    - by techaddict
    I want to hack a device which connects via USB, and plug a bluetooth USB dongle to the end of the USB cable (using a female to female adapter), and then connect to that device from another USB bluetooth dongle connected to my computer. How can I do this? It is straightforward? I don't want to spend $30 before I know how to do this. Also I think another concern is that the USB cable is providing power to the device. So I think that means I would also have to hack it for power. I have created this diagram in Photoshop to illustrate my intent: (NOTE: it won't be a USB mouse, as that would be pointless because there are already wireless mice in existence. The mouse is displayed for illustrative purposes) Don't tell me "it won't work". Because I KNOW it WILL work. Think for example, PS3 controller. That works, and in fact I was able to get it working with my laptop, over bluetooth. I just want to know HOW to make it work.

    Read the article

  • ownership of hard drive recoveery of files Windows 7

    - by Jeff
    Here is the issue. I have an old laptop that died that was running xp. I now have a win 7 laptop. I need to get the files off the old drive. Win 7 will not let me take ownership of the drive. I can runn the comand prompt in regular mode and do a dir on the drive that shows up as Q: drive in regular mode. I gives me the volume as c and the serial number. I can not take ownership in regular mode with the comand prompt or other means. Microsoft site says use safe mode with networking. So I go to safe mode the drive shows up as G: in safe mode. I use the comand prompt Takeown /f G: and get the device is not ready error. I am at a loss. All I want is to retrieve my files from this drive. Any ideas or sugestions. I don't see how you can dir and get some info in one mode and not acces it in another. I have to get ownership and permissions fixed to get in the drive to get my files. Thanks in advance. I might add that I am using a usb3.0 to ide/sata cable adapter. Software came with the device but I can't make heads or tails out of the manual to know if any of the software can help me. The soft ware is PCClone Ex lite, and Clone Drive Soft ware

    Read the article

  • computer freezes but music continues

    - by Danny
    Recently I have had a problem where my computer will freeze completely but if I happen to be streaming Pandora in a tab that will continue playing. If I wait about 2-5 minutes it will eventually come back and start working normally. I also noticed that during the period that it is unresponsive that the HDD activity light stays lit the whole time, not flashing. I've ran memtest86+ and a diagnostic from Western Digital for my HDD model and none of them reported any errors. The specs for my computer are 1 x ASRock H55M/USB3 R2.0 LGA 1156 Intel H55 HDMI USB 3.0 Micro ATX Intel Motherboard 1 x CORSAIR Enthusiast Series CMPSU-550VX 550W ATX12V V2.2 SLI Ready CrossFire Ready 80 PLUS Certified Active PFC Compatible with Core i7 Power Supply 1 x Intel Core i3-540 Clarkdale 3.06GHz LGA 1156 73W Dual-Core Desktop Processor Intel HD Graphics BX80616I3540 1 x G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model F3-12800CL9D-4GBNQ 1 x ASUS PCE-N13 PCI Express 150/300Mbps Transfer/Receive Rate Wireless Adapter 1 x EVGA 01G-P3-1556-KR GeForce GTX 550 Ti (Fermi) FPB 1GB 192-bit GDDR5 PCI Express 2.0 x16 HDCP Ready SLI Support Video Card I can't imagine what would be causing these problems.

    Read the article

  • How to connect computers to a network printer behind a router?

    - by kokbira
    General question: How to connect computers to an IP printer behind a router? Particular question: How to connect C-1 and C-2 to PRI? What? Where? [ISP] | | -> IPs:200.X.X.X/other configs:DC | [R-1] | | -> IPs:10.1.X.X locked by MAC,M:255.0.0.0,G:10.1.0.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [PRI] IP:10.1.7.7 [R-2] IP: 10.1.0.1,MAC:A | | -> IPs:192.168.1.X,M:255.255.255.0,G:192.168.1.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [C-1] IP:192.168.1.2 [C-2] IP:192.168.1.3,MAC:A Glossary and details: ------------------------------------------------------------------------------------ - IP: IP. - IPs: Some IP range. - M: Mask. - G: Gateway. - MAC:A: A MAC address that I will not inform you :) - DC: Don't care. - ISP: Internet Service Provider (not so much details about it on that case). - R-1: A real router or some concatenated so IP range bellow that block is 10.1.X.X and above is ISP. The provided IPs are provided by MAC. As all available addresses are in use, you must clone an existing one to join with a new device (and to disconnect the cloned one). - PRI: An network printer (some people here call that IP printer). - R-2: A TP-LINK TL-WR340G, mine wireless router (since my computer does not have ethernet input, it is my ethernet-wifi adapter :), admin access, MAC address cloned from C-2 (MAC:A). I've to configure 10.0.1.1 and 10.0.1.2 as DNS addresses, other wise I cannot connect C-1 and C-2 to Internet. - C-1: My computer, a CCE XLE-425 (remember: no ethernet input), with Windows 7, admin access. - C-2: another computer with better configs than mine, MAC:A, Windows XP. Requirements: I want to print, to access Internet and to do it myself (no need to call network admin men in black people). Pay attention to MAC clones and DNS info.

    Read the article

  • Gigabit network limited to 25MB/s by CPU. How to make it faster?

    - by netvope
    I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? The other computers in the network can usually transfer at 50+MB/s without problems. And a minor question: How can I find out what is the driver in use for eth0?

    Read the article

  • Access node.js local server though mobile via same shared wifi

    - by laggingreflex
    EDIT: I was stuck in this situation before but then it was Apache-related But this time I'm using NodeJS, so the old answer doesn't help. I'm running apache a NodeJS webserver (on port 80) on Windows 7. I want to access the webserver through my mobile which shares the wifi router with my pc locally. http://localhost works from PC. But I can't access http://192.168.1.4 from either my phone or even my computer. ipconfig /all on my computer lists my ip address as 192.168.1.4 Wireless LAN adapter Wireless Network Connection: IPv4 Address. . . . . . . . . . . : 192.168.1.4(Preferred) I can ping my phone's (internal) ip address [192.168.1.5] from PC and vice-versa, I can ping my PC [192.168.1.4] from my phone. So why can't I access http://192.168.1.4 from my phone? (or PC) Firewall is off.

    Read the article

  • "Ethernet" doesn't have a valid IP configuration

    - by Xuzuno
    I'm using an ethernet cord to connect to my internet and it has been working well until Thursday morning when I turned on my laptop (Windows 8) to see a yellow triangle sign in the bottom right hand corner, in front of the ethernet connected symbol. Since then I haven't been able been able to access the internet from my computer. When I hover over it, it says that it is an "Unidentified network" and there is "No internet access". I've run the Windows 8 troubleshooting and it says that the problem found was ""Ethernet" doesn't have a valid IP configuration", but I'm unsure how to fix it. I'm thinking that the problem is to do with my computer rather than my network, because I've tried another laptop (Windows 7) through the same ethernet cable and connection and the internet works fine on the other laptop. I've tried so many fixes that I've found online, with none of them actually working. Yesterday I even tried a full system reset, where I re-installed Windows 8, re-partitioned and wiped everything off the hard drive, but it still appears have the exact same problem. Today I also purchased and tried a new ethernet cable which didn't work, so I then purchased a USB to Ethernet adapter, to make sure that it wasn't my ethernet port on my laptop that was faulty. That didn't work either, and the same problem still remains. I feel like I've tried everything, so can someone please help me?

    Read the article

< Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >