Search Results

Search found 3604 results on 145 pages for 'bigced 21'.

Page 95/145 | < Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >

  • XFS: No space left on device

    - by beketa
    I am using XFS on small HDD (/dev/sdb1, less than 1TB) and storing many small files (-32KB). df -h and -i show that it has available space. # df -hv Filesystem Size Used Avail Use% Mounted on /dev/sda3 127G 19G 102G 16% / tmpfs 16G 0 16G 0% /lib/init/rw udev 16G 168K 16G 1% /dev tmpfs 16G 0 16G 0% /dev/shm /dev/sda1 99M 20M 75M 21% /boot /dev/sdb1 136G 123G 14G 91% /mnt/sdb1 # df -iv Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda3 8421376 36199 8385177 1% / tmpfs 4126158 5 4126153 1% /lib/init/rw udev 4124934 671 4124263 1% /dev tmpfs 4126158 1 4126157 1% /dev/shm /dev/sda1 26112 222 25890 1% /boot /dev/sdb1 24905120 11076608 13828512 45% /mnt/sdb1 However I got No space left on device error. # touch /mnt/sdb1/test touch: cannot touch `/mnt/sdb1/test': No space left on device I think inode64 issue is not related to this case because drive is less than 1TB and df -i shows that there are free inodes. I unmounted and mounted with -o inode64 but got the same error. xfs_repair does not report any problem. xfs_info shows drive information as follows. # xfs_info /dev/sdb1 meta-data=/dev/sdb1 isize=1024 agcount=16, agsize=2227764 blks = sectsz=512 attr=2 data = bsize=4096 blocks=35644210, imaxpct=25 = sunit=0 swidth=0 blks naming =version 2 bsize=4096 ascii-ci=0 log =internal bsize=4096 blocks=17404, version=2 = sectsz=512 sunit=0 blks, lazy-count=1 realtime =none extsz=4096 blocks=0, rtextents=0 Any ideas? Thanks!

    Read the article

  • Sound doesn't work anymore after replacing RAM

    - by thejh
    Hello, today, I replaced one old RAM module with two newer, bigger ones, but now, the sound doesn't seem to work anymore. Already ran alsaconf and it didn't help. Output of lspci for the audio device: 00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1) Subsystem: Giga-byte Technology Device a002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel The audio device is onboard and has six configurable outputs, two or so are also capable of being an input (if I remember it correctly), but I don't know how to control it under linux. Does somebody know how/whether replacing the RAM could be related to my problem and/or how to fix it?

    Read the article

  • Why does my ftp(e)s server fails like half of the time

    - by user1092608
    I have this discussion at work regarding our ftp server running via vsftpd. Initially, we have opted to serve ftpes instead of sftp because this seemed the most flexible and straightforward solution for our server to have secure file transmission. Afterwards, our ftp server seems to be a source of issues for our end users. Half of the time, users complain about not working ftp connections. I must say, i tested our FTP trough different infrastructures (=in the field, at random times at random places) and indeed, sometimes behind some configurations (=no idea how they are configured, because the 'field' testing), i recieve errors. Some of the are: Error: Failed to retrieve directory listing (filezilla) Furthermore, behind my basic home configuration, everything seems to be running fine. I (think I) did all the basic configuration checks (passive mode?, firewall for all ports?, ...) and can't seem to find the source. Being a bunch of techies at our small office, yet knowing nothing about infrastructure, some start suggesting that ftps protocol could be the source of issues. ("No, i only knew sftp so far" "Ftps is not widespread"). I, however, strongly doubt this hypothesis, since reading around on the www, asking questions on serverfault, everyone seems to deny this. So, as I would like to avoid reconfiguring, since this involves messing around in our SSH service, our virtual user setup and ftp service, i would need some advice on 1) what could be potentially the general cause? 2) do you have some general tips? 3) would you mind having a look at my configuration file? ----- General Settings ----- write_enable=YES dirmessage_enable=YES nopriv_user=ftpsecure ftpd_banner="Welcome to XXXX FTP!" hide_ids=YES hide_file=.* max_per_ip=10 max_clients=10 local_enable=YES local_umask=022 chroot_local_user=YES secure_chroot_dir=/usr/share/empty userlist_enable=NO userlist_deny=YES userlist_file=/etc/vsftp_deny_users guest_enable=YES guest_username=ftpvirtual virtual_use_local_privs=YES user_sub_token=$USER local_root=/srv/ftp/ftpvirtual/$USER anonymous_enable=NO syslog_enable=NO xferlog_enable=YES xferlog_file=/var/log/vsftpd_xfer.log connect_from_port_20=YES pam_service_name=vsftpd listen=YES listen_port=21 pasv_enable=YES pasv_min_port=30000 pasv_max_port=30030 pasv_address=foo ssl_enable=YES rsa_cert_file=/etc/vsftpd.pem rsa_private_key_file=/etc/vsftpd.pem force_local_data_ssl=YES force_local_logins_ssl=YES ssl_tlsv1=YES ssl_sslv2=YES ssl_sslv3=YES ssl_ciphers=HIGH anon_mkdir_write_enable=NO anon_root=/srv/ftp anon_upload_enable=NO idle_session_timeout=900 log_ftp_protocol=NO dsa_cert_file=/etc/vsftpd.pem Thanks

    Read the article

  • Cisco 7206vxr cpu reducing

    - by naimson
    I have a 7206VXR (NPE-G2) . At the rate of 140 kpps i gain 80% of cpu . So i looking for ways how to reduce it? So i want to turn off netflow(but don't want to this,monitoring is highly important for me), but it will give me only 10-20% ? At this moment with 84kpps i have 58% sh processes cpu sorted give me this. PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 109 163534600 537236763 304 35.38% 32.83% 16.85% 0 IP Input 67 829396 52280 15864 0.15% 0.01% 0.00% 0 Per-minute Jobs 68 5542736 3053476 1815 0.15% 0.18% 0.16% 0 Per-Second Jobs 51 635852 1116315 569 0.07% 0.03% 0.02% 0 Net Background 329 120396 4607274 26 0.07% 0.00% 0.00% 0 EIGRP-IPv4 Hello 105 50508 95032488 0 0.07% 0.05% 0.05% 0 IPAM Manager 6 4068580 476916 8531 0.00% 0.07% 0.05% 0 Check heaps 7 7768 3634 2137 0.00% 0.00% 0.00% 0 Pool Manager 8 0 1 0 0.00% 0.00% 0.00% 0 DiscardQ Backgro 10 8 708 11 0.00% 0.00% 0.00% 0 WATCH_AFS 5 0 1 0 0.00% 0.00% 0.00% 0 RO Notify Timers 12 0 2 0 0.00% 0.00% 0.00% 0 ATM VC Auto Crea 9 0 2 0 0.00% 0.00% 0.00% 0 Timers 11 0 2 0 0.00% 0.00% 0.00% 0 ATM AutoVC Perio 13 296 610532 0 0.00% 0.00% 0.00% 0 IPC Event Notifi 16 0 1 0 0.00% 0.00% 0.00% 0 IPC Zone Manager 17 3584 2980311 1 0.00% 0.00% 0.00% 0 IPC Periodic Tim 4 0 1 0 0.00% 0.00% 0.00% 0 EDDRI_MAIN 19 0 1 0 0.00% 0.00% 0.00% 0 IPC Process leve 20 0 1 0 0.00% 0.00% 0.00% 0 IPC Seat Manager 21 96 174453 0 0.00% 0.00% 0.00% 0 IPC Check Queue 14 4 50890 0 0.00% 0.00% 0.00% 0 IPC Dynamic Cach 3 0 1 0 0.00% 0.00% 0.00% 0 cpf_process_tpQ 24 756 305371 2 0.00% 0.00% 0.00% 0 IPC Keep Alive M 25 2340 610561 3 0.00% 0.00% 0.00% 0 IPC Loadometer 22 0 1 0 0.00% 0.00% 0.00% 0 IPC Seat RX Cont 15 0 1 0 0.00% 0.00% 0.00% 0 IPC Session Serv 18 1620 2980310 0 0.00% 0.00% 0.00% 0 IPC Deferred Por 29 0 1 0 0.00% 0.00% 0.00% 0 Exception contro sh run(greped): http://pastie.org/5483194 Hardware: c7200p-adventerprisek9-mz.151-4.M1.bin Cisco 7206VXR (NPE-G2) processor (revision A) with 917504K/65536K bytes of memory. Processor board ID 2xxxxxxx MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2 6 slot VXR midplane, Version 2.1

    Read the article

  • Have some questions about setting up a VPN to my private cloud servers

    - by Pure.Krome
    I've got a number of Virtual Servers running at a pretty big Cloud provider. They are all running Windows 2008 R2. I have a CISCO ASA firewall in front of them. Currently, I've got all ports blocked except 80/443/21/3386 (for Remote Desktop). I asked to have a VPN enabled on the firewall and they said it's easy to do BUT I need to use the 3rd party Cisco software. Now, I don't want to get into a debate about it .. but we don't want to install anything extra on our -client- computers. We all use Windows 7 and we love using the built in VPN client to connect to other private LANS we have setup in other locations. So i'm wondering what options I have to create a VPN tunnel to our private cloud LAN? All our cloud servers are part of WORKGROUP, so there's no Active Directory .. nor do we want to install all that. Secondly, we know we can open up a firewall port - so any ports for starting a VPN is fine! Lastly, I was thinking of just using one of the existing servers as the VPN server (and using the Windows VPN software) .. but I'm not sure this is a good thing? Remember - we just want to use the baked in VPN software in Windows 7 .. which is PPTP or SSTP or L2TP/IPSEC. I would -LOVE- to use some free OSS software. For usernames/passwords? We'd probably just have one account .. like U:Hithere P:whatever.. so we don't need any hardcore account management, like Active Directory, etc. So does anyone have any ideas?

    Read the article

  • Possible Hack with FTP - What are the solutions?

    - by iamrohitbanga
    I was reading the FTP rfc and hence had this idea. Suppose there are several public ftp servers that allow anonymous user login. I open a control connection on port 21 to each of these servers. Now suppose there is a web server a.com with ip address x.y.z.w listening on port 80. FTP allows a user to specify the host on which the data connection is to be setup. So a user specifies the host and port number of a.com web server. Now the ftp server starts sending data to a.com for which it is not a valid HTTP request and hence it is rejected. But a.com notes that the invalid http request came from a public ftp server and not my ip address. Can this not lead to a distributed attack by utilizing all public ftp servers. worse still the the data being sent by ftp server could be a valid http request which could trigger a.com to send a file back to the ftp server. Is there a solution for this or is it no problem at all.

    Read the article

  • Very high CPU and low RAM usage - is it possible to place some of swap some of the CPU usage to the RAM (with CloudLinux LVE Manager installed)?

    - by Chriswede
    I had to install CloudLinux so that I could somewhat controle the CPU ussage and more importantly the Concurrent-Connections the Websites use. But as you can see the Server load is way to high and thats why some sites take up to 10 sec. to load! Server load 22.46 (8 CPUs) (!) Memory Used 36.32% (2,959,188 of 8,146,632) (ok) Swap Used 0.01% (132 of 2,104,504) (ok) Server: 8 x Intel(R) Xeon(R) CPU E31230 @ 3.20GHz Memory: 8143680k/9437184k available (2621k kernel code, 234872k reserved, 1403k data, 244k init) Linux Yesterday: Total of 214,514 Page-views (Awstat) Now my question: Can I shift some of the CPU usage to the RAM? Or what else could I do to make the sites run faster (websites are dynamic - so SQL heavy) Thanks top - 06:10:14 up 29 days, 20:37, 1 user, load average: 11.16, 13.19, 12.81 Tasks: 526 total, 1 running, 524 sleeping, 0 stopped, 1 zombie Cpu(s): 42.9%us, 21.4%sy, 0.0%ni, 33.7%id, 1.9%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 8146632k total, 7427632k used, 719000k free, 131020k buffers Swap: 2104504k total, 132k used, 2104372k free, 4506644k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 318421 mysql 15 0 1315m 754m 4964 S 474.9 9.5 95300:17 mysqld 6928 root 10 -5 0 0 0 S 2.0 0.0 90:42.85 kondemand/3 476047 headus 17 0 172m 19m 10m S 1.7 0.2 0:00.05 php 476055 headus 18 0 172m 18m 9.9m S 1.7 0.2 0:00.05 php 476056 headus 15 0 172m 19m 10m S 1.7 0.2 0:00.05 php 476061 headus 18 0 172m 19m 10m S 1.7 0.2 0:00.05 php 6930 root 10 -5 0 0 0 S 1.3 0.0 161:48.12 kondemand/5 6931 root 10 -5 0 0 0 S 1.3 0.0 193:11.74 kondemand/6 476049 headus 17 0 172m 19m 10m S 1.3 0.2 0:00.04 php 476050 headus 15 0 172m 18m 9.9m S 1.3 0.2 0:00.04 php 476057 headus 17 0 172m 18m 9.9m S 1.3 0.2 0:00.04 php 6926 root 10 -5 0 0 0 S 1.0 0.0 90:13.88 kondemand/1 6932 root 10 -5 0 0 0 S 1.0 0.0 247:47.50 kondemand/7 476064 worldof 18 0 172m 19m 10m S 1.0 0.2 0:00.03 php 6927 root 10 -5 0 0 0 S 0.7 0.0 93:52.80 kondemand/2 6929 root 10 -5 0 0 0 S 0.3 0.0 161:54.38 kondemand/4 8459 root 15 0 103m 5576 1268 S 0.3 0.1 54:45.39 lvest

    Read the article

  • "No such file or directory"?

    - by user1509541
    Ok, so I have a VDS laying around, and I thought I would turn it into a TF2 game server. When I connect to my server through PuTTY, and use wget to download the package "hldsupdatetool.bin" from Steampowered.com. I go to run it and it says "No such file or directory found". When I use "ls" to see what files are in directory, it lists "hldsupdatetool.bin" as being in the directory. So, why is it saying it's not there? This has been a headache for the past 2 days. It's returning: root@10004:~# wget http://www.steampowered.com/download/hldsupdatetool.bin --2012-07-08 06:04:49-- http://www.steampowered.com/download/hldsupdatetool.bin Resolving www.steampowered.com... 208.64.202.68 Connecting to www.steampowered.com|208.64.202.68|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 3513408 (3.4M) [application/octet-stream] Saving to: “hldsupdatetool.bin.3” 100%[======================================>] 3,513,408 2.45M/s in 1.4s 2012-07-08 06:04:51 (2.45 MB/s) - “hldsupdatetool.bin.3” saved [3513408/3513408] root@10004:~# chmod +x hldsupdatetool.bin.3 root@10004:~# ./hldsupdatetool.bin.3 -bash: ./hldsupdatetool.bin.3: No such file or directory root@10004:~# More: root@10004:~# ls ffmpeg-packages hldsupdatetool.bin.1 hldsupdatetool.bin.3 hldsupdatetool.bin hldsupdatetool.bin.2 setup.sh root@10004:~# ls -la total 13828 drwx------ 4 root root 4096 Jul 8 06:04 . drwxr-xr-x 21 root root 4096 Jul 8 05:57 .. -rw------- 1 root root 8799 Jul 8 06:26 .bash_history -rw-r--r-- 1 root root 570 Jan 31 2010 .bashrc -rw-r--r-- 1 root root 4 Jul 2 19:39 .custombuild drwxr-xr-x 2 root root 4096 Jul 4 18:49 ffmpeg-packages ---x--xrwx 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin -rwxr-xr-x 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin.1 -rw-r--r-- 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin.2 -rwxr-xr-x 1 root root 3513408 Sep 2 2005 hldsupdatetool.bin.3 -rw-r--r-- 1 root root 140 Nov 19 2007 .profile -rw------- 1 root root 1024 Jul 2 19:49 .rnd -rwxr-xr-x 1 root root 38866 May 23 22:02 setup.sh drwxr-xr-x 2 root root 4096 Jul 2 19:44 .ssh root@10004:~#

    Read the article

  • where is my disk space?

    - by user166241
    I recently had a problem with .xsession-errors file - it became very big ( 90GB) and took all disk space: How I can check what takes disk space in /tmp?. I cleaned it with command > .xsession-errors but after an hour it became large again. So I deleted it (rm .xsession-errors) - it helped because it wasn't recreated but again after hour disk space disappeared - now there is no .xsession-errors anymore but I don't know where is the memory: df Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda1 106640456 101223392 4 100% / udev 8166744 8 8166736 1% /dev tmpfs 3270224 972 3269252 1% /run none 5120 0 5120 0% /run/lock none 8175552 152 8175400 1% /run/shm du -sc * .[^.]* | sort -n 0 initrd.img 0 initrd.img.old 0 proc 0 sys 0 vmlinuz 0 vmlinuz.old 4 cdrom 4 lib64 4 media 4 mnt 4 selinux 8 dev 12 srv 16 lost+found 68 tmp 1124 run 3396 lib32 5164 .rpmdb 5540 root 8888 sbin 9120 bin 17132 etc 106080 opt 116956 boot 861908 lib 3530584 usr 3821836 var 13371260 home 21859112 total So there is around 100GB used but executing du -sc * .[^.]* | sort -n in root directory finds only ~21 GB - so what takes 80GB?? How to check it? I suspect that when I deleted the `.xsession-errors' file the errors were redirected somwhere else - but where?

    Read the article

  • Passive mode FTP file download hangs from specific machine

    - by chiptuned
    I have a server which is an AWS instance that just cannot download files from a specific FTP server. I can connect to the FTP server fine and run some commands, but when I request a file it just hangs. Here is the debug output of the base linux ftp client after login: ---> SYST 215 UNIX Type: Apache FtpServer Remote system type is UNIX. ftp> get outgoing/catalog.gz catalog.gz local: catalog.gz remote: outgoing/catalog.gz ---> PASV 227 Entering Passive Mode (64,156,167,125,135,191) ---> RETR outgoing/catalog.gz 150 File status okay; about to open data connection. Thats it. Then it just sits there and nothing transfers. I have verified that a data connection is made but the client gets no data. ? ss -nt dst 64.156.167.125 State Recv-Q Send-Q Local Address:Port Peer Address:Port ESTAB 0 0 10.185.147.150:41190 64.156.167.125:21 ESTAB 0 0 10.185.147.150:48871 64.156.167.125:48557 The FTP server is not in my control and downloads from other FTP servers in passive mode have worked. Active mode does not work as the system is behind a firewall. Every FTP client I've tried has the same problem. The download works from other systems, even from other AWS instances I have with the same Security Group. Not necessarily the same distro or config though. I understand it may be some issue on the server side, but I want to know what it is about my particular machine where the transfer hangs and where on every other machine I can get my hands on, it works. Please let me know what the culprit on the client side could be or ideas on what else to look at.

    Read the article

  • Can't connect to wi-fi hotspot in Ubuntu 11.10

    - by ht3t
    I'm new to Ubuntu. I'm having a wireless network problem in Ubuntu 11.10. I made a hotspot using Connectify from a computer which is running Windows 7. I can access it in Windows 7 but not in Ubuntu 11.10. Every time I access it,I get a message "disconnected". I'm using msi fx 400 notebook with Intel Centrino wireless -N 1000 wireless card. Ubuntu version is 11.10 with KDE desktop. $ sudo lshw -c network [sudo] password for ht3t: *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:56:b8:f0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:44 memory:e7400000-e7401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 40:61:86:b6:b1:a2 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw IP=192.168.21.107 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:9000(size=256) memory:e6004000-e6004fff memory:e6000000-e6003fff I can't do anything without internet connection. How can I fix this?

    Read the article

  • vmware server 64 bit on ubuntu 9.10 64 bit with P2V windows 2003 SBS poor network speed

    - by RobertHC
    configuration is ubuntu 2.6.31-21 64 bit vmware 2.0.2 64 bit last release hardware is core 2 quad with 8GB ram guest is win 2003 server SBS 32 bit Dear friends, we have a converted physical to virtual windows sbs 2003, converted with last converter available nowadays http://www.vmware.com/products/converter/ vCenter converter. Running the P2V 2K3 SBS on vmware server, it does boot fine, but we do note an abnormal CPU activity and a poor lan speed. As attempts we did what follow. We removed all unneeded peripherals, we removed one NIC (phisycal server was 2 nics), we changed the vmx to ged the nic recognized as intel instead than amd, we removed 1 cpu (physical was 2 cpu), we removed anything was reported as failed driver from system events monitor. Nothing to do, no way and funny results. Let's read some tests results. All are made with the same file copied in different source folders. Copying from client side (both directions copy, to/from server) results are i.e. 10 seconds, copying the same files from server side (again from and to server) results are different... from client to server, speed is round about (bit more) 10 seconds, but from server to client direction is slower: double the time. Beeing very fast and launching a simultaneous copy "from server to client"+"from client to server", this made from the server side, results in a stuck traffic... 45 seconds to do the copy. vmware tools are installed and e1000 driver has been updated. With one processor CPU activity is still going up and down but much less than with two. Because of test, we installed win 2k8 STD 64 bit. We repeated all the above tests with exactly the same file result is just one: always 5 seconds (this matches the lan speed) Any idea about this issue is welcome and thank you if any. Kind regards R.

    Read the article

  • Howto detect fake RAM

    - by Michael
    I just bought a virtual server which should have 2GB of RAM. Now i got a server with 4gb which looks very strange to me. I think it is just a virtual RAM. dmidecode only ouputs /dev/mem: Operation not permitted How can i check if it's a real RAM or just a virtual one? free -m outputs: total used free shared buffers cached Mem: 4093 364 3728 0 0 346 -/+ buffers/cache: 18 4074 Swap: 0 0 0 Output from cat /proc/user_beancounters Version: 2.5 uid resource held maxheld barrier limit failcnt 137: kmemsize 8922287 10194944 2145910784 2145910784 0 lockedpages 0 0 523904 523904 0 privvmpages 13387 59112 9223372036854775807 9223372036854775807 0 shmpages 769 785 9223372036854775807 9223372036854775807 0 dummy 0 0 9223372036854775807 9223372036854775807 0 numproc 22 54 9223372036854775807 9223372036854775807 0 physpages 93377 106010 0 1047808 0 vmguarpages 0 0 9223372036854775807 9223372036854775807 0 oomguarpages 2471 2473 9223372036854775807 9223372036854775807 0 numtcpsock 5 21 9223372036854775807 9223372036854775807 0 numflock 4 13 9223372036854775807 9223372036854775807 0 numpty 1 1 9223372036854775807 9223372036854775807 0 numsiginfo 0 39 9223372036854775807 9223372036854775807 0 tcpsndbuf 102592 381632 9223372036854775807 9223372036854775807 0 tcprcvbuf 81920 4820184 9223372036854775807 9223372036854775807 0 othersockbuf 4624 61632 9223372036854775807 9223372036854775807 0 dgramrcvbuf 0 9248 9223372036854775807 9223372036854775807 0 numothersock 39 56 9223372036854775807 9223372036854775807 0 dcachesize 4178917 4232732 1072955392 1072955392 0 numfile 378 535 9223372036854775807 9223372036854775807 0 dummy 0 0 9223372036854775807 9223372036854775807 0 dummy 0 0 9223372036854775807 9223372036854775807 0 dummy 0 0 9223372036854775807 9223372036854775807 0 numiptent 24 24 9223372036854775807 9223372036854775807 0

    Read the article

  • very diferent results from df after few seconds

    - by tatus2
    When the backup moves the files from one to the other server the results from df changing every some seconds in impossible manner. On source host is running rsync. On destination host I'm running every few seconds following command: echo `date` `df|grep md0` Results are below: Sat Jun 29 23:57:12 CEST 2013 /dev/md0 4326425568 579316100 3527339636 15% /MD0 Sat Jun 29 23:57:14 CEST 2013 /dev/md0 4326425568 852513700 3254142036 21% /MD0 Sat Jun 29 23:57:15 CEST 2013 /dev/md0 4326425568 969970340 3136685396 24% /MD0 Sat Jun 29 23:57:17 CEST 2013 /dev/md0 4326425568 1255222180 2851433556 31% /MD0 Sat Jun 29 23:57:20 CEST 2013 /dev/md0 4326425568 1276006720 2830649016 32% /MD0 Sat Jun 29 23:57:24 CEST 2013 /dev/md0 4326425568 1355440016 2751215720 34% /MD0 Sat Jun 29 23:57:26 CEST 2013 /dev/md0 4326425568 1425090960 2681564776 35% /MD0 Sat Jun 29 23:57:27 CEST 2013 /dev/md0 4326425568 1474601872 2632053864 36% /MD0 Sat Jun 29 23:57:28 CEST 2013 /dev/md0 4326425568 1493627384 2613028352 37% /MD0 Sat Jun 29 23:57:32 CEST 2013 /dev/md0 4326425568 615934400 3490721336 15% /MD0 Sat Jun 29 23:57:33 CEST 2013 /dev/md0 4326425568 636071360 3470584376 16% /MD0 as you can see I start from USE of 15% and after 15 seconds I'm at 37% (I don't need to mention that the backup can not copy this huge amount of data in so short time). After ~20 sec the cycle closes. I'm again roughly by the same usage as earlier. The value is reasonable ca. 35 Mb were copied. Can somebody explain me what is going on? Does df only make an estimation of usage instead of used value?

    Read the article

  • mysqld - master to slave replication using rsync innodb, sequence number issues

    - by Luis
    I've read several of the related topics posted here, but I have not been able to avoid this innodb error. The steps I've taken to replicate data from a Slackware server - 5.5.27-log (S) to a FreeBSD slave - 5.5.21-log (F) were these: (S) flush tables with read lock; (S) in another terminal show master status; (S) stop mysqld via command line in third terminal; (F) while both servers are stopped, rsync mysql datadir from (S), excluding master.info, mysql-bin and relay-* files; (F) start mysqld (skip-slave) 121018 12:03:29 InnoDB: Error: page 7 log sequence number 456388912904 InnoDB: is in the future! Current system log sequence number 453905468629. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.5/en/forcing-innodb-recovery.html InnoDB: for more information. This kind of error happens for a lot of tables. I know I can use dump, but the database is large, ca. 70GB and the systems are slow (old), so would like to get this replication to work with data transfer. What should I try to solve this issue?

    Read the article

  • Can't connect to FTP server from a specific location

    - by wv_pip
    Last week while uploading website files to our server via FTP, the transfer failed. Ever since then, I haven't been able to connect to the server from work. I can connect just fine from home, or by using an FTP app on my cell phone as long as I'm on the cell network. I can't access the server from any machine on my work network. It's not a credential issue, either. The error message that I always get says that a connection cannot be established, and I am never prompted for my credentials. I have changed absolutely nothing on our domain controller or our firewall/router. I've contacted our ISP (who hosts the website/FTP server) and they can't find anything wrong on their end. They insist that it must be something here at the office that is blocking access. I've also tested access to other FTP servers (ea.com, nvidia.com, etc.) so I know that port 21 is not being blocked. I'm totally stumped. Any help is much appreciated. EDIT: wireshark info here: http://www.cloudshark.org/captures/85a118ae9296?filter=ip.dst%3D%3D66.118.64.208

    Read the article

  • Very diferent results from df after a few seconds

    - by tatus2
    When the backup moves the files from one server to the other the results from df change every few seconds in an impossible manner. The source host is running rsync. On the destination host I'm running the following command every few seconds: echo `date` `df|grep md0` Results are below: Sat Jun 29 23:57:12 CEST 2013 /dev/md0 4326425568 579316100 3527339636 15% /MD0 Sat Jun 29 23:57:14 CEST 2013 /dev/md0 4326425568 852513700 3254142036 21% /MD0 Sat Jun 29 23:57:15 CEST 2013 /dev/md0 4326425568 969970340 3136685396 24% /MD0 Sat Jun 29 23:57:17 CEST 2013 /dev/md0 4326425568 1255222180 2851433556 31% /MD0 Sat Jun 29 23:57:20 CEST 2013 /dev/md0 4326425568 1276006720 2830649016 32% /MD0 Sat Jun 29 23:57:24 CEST 2013 /dev/md0 4326425568 1355440016 2751215720 34% /MD0 Sat Jun 29 23:57:26 CEST 2013 /dev/md0 4326425568 1425090960 2681564776 35% /MD0 Sat Jun 29 23:57:27 CEST 2013 /dev/md0 4326425568 1474601872 2632053864 36% /MD0 Sat Jun 29 23:57:28 CEST 2013 /dev/md0 4326425568 1493627384 2613028352 37% /MD0 Sat Jun 29 23:57:32 CEST 2013 /dev/md0 4326425568 615934400 3490721336 15% /MD0 Sat Jun 29 23:57:33 CEST 2013 /dev/md0 4326425568 636071360 3470584376 16% /MD0 As you can see I start from USE of 15% and after 15 seconds I'm at 37% (I don't need to mention that the backup can not copy this huge amount of data in such a short time). After ~20 seconds the cycle closes. I'm again roughly at the same usage as earlier. The value is reasonable, ca. 35 Mb were copied. Can somebody explain to me what is going on? Does df only make an estimation of usage instead of used value?

    Read the article

  • form_dropdown in codeigniter

    - by Patrick
    I'm getting a strange behaviour from form_dropdown - basically, when I reload the page after validation, the values are screwed up. this bit generates 3 drop downs with days, months and years: $days = array(0 => 'Day...'); for ($i = 1; $i <= 31; $i++) { $days[] = $i; } $months = array(0 => 'Month...', ); for ($i = 1; $i <= 12; $i++) { $months[] = $i; } $years = array(0 => 'Year...'); for ($i = 2010; $i <= 2012; $i++) { $years[$i] = $i; echo "<pre>"; print_r($years); echo "</pre>";//remove this } $selected_day = (isset($selected_day)) ? $selected_day : 0; $selected_month = (isset($selected_month)) ? $selected_month : 0; $selected_year = (isset($selected_year)) ? $selected_year : 0; echo "<p>"; echo form_label('Select date:', 'day', array('class' => 'left')); echo form_dropdown('day', $days, $selected_day, 'class="combosmall"'); echo form_dropdown('month', $months, $selected_month, 'class="combosmall"'); echo form_dropdown('year', $years, $selected_year, 'class="combosmall"'); echo "</p>"; ...and generates this: <p><label for="day" class="left">Select date:</label><select name="day" class="combosmall"> <option value="0" selected="selected">Day...</option> <option value="1">1</option> <option value="2">2</option> <option value="3">3</option> <option value="4">4</option> <option value="5">5</option> <option value="6">6</option> <option value="7">7</option> <option value="8">8</option> <option value="9">9</option> <option value="10">10</option> <option value="11">11</option> <option value="12">12</option> <option value="13">13</option> <option value="14">14</option> <option value="15">15</option> <option value="16">16</option> <option value="17">17</option> <option value="18">18</option> <option value="19">19</option> <option value="20">20</option> <option value="21">21</option> <option value="22">22</option> <option value="23">23</option> <option value="24">24</option> <option value="25">25</option> <option value="26">26</option> <option value="27">27</option> <option value="28">28</option> <option value="29">29</option> <option value="30">30</option> <option value="31">31</option> </select><select name="month" class="combosmall"> <option value="0" selected="selected">Month...</option> <option value="1">1</option> <option value="2">2</option> <option value="3">3</option> <option value="4">4</option> <option value="5">5</option> <option value="6">6</option> <option value="7">7</option> <option value="8">8</option> <option value="9">9</option> <option value="10">10</option> <option value="11">11</option> <option value="12">12</option> </select><select name="year" class="combosmall"> <option value="0" selected="selected">Year...</option> <option value="2010">2010</option> <option value="2011">2011</option> <option value="2012">2012</option> </select></p> however, when the form is reloaded after validation, the same code above generates this: <!-- days and months... --> <select name="year" class="combosmall"> <option value="0" selected="selected">Year...</option> <option value="1">2010</option> <option value="2">2011</option> <option value="3">2012</option> </select> So basically the value start from 1 instead of 2010. The same happens to days and months but obviously it doesn't make any difference in this particular case as the values would start from 1 anyway. How can I fix this - and why does it happen?

    Read the article

  • Snort's problems in generating alert from Darpa 1998 intrusion detection dataset.

    - by manofseven2
    Hi. I’m working on DARPA 1998 intrusion detection dataset. When I run snort on this dataset (outside.tcpdump file), snort don’t generate complete list of alerts. It means snort start from last few hours of tcpdump file and generate alerts about this section of file and all of packets in first hours are ignored. Another problem in generatin alert is in time stamp of generated alerts. This means when I run snort on a specific day of dataset, snort insert incorrect time stamp for that alert. The configuration and command line statement and other information about my research are: Snort version: 2.8.6 Operating system: windows XP Rule version: snortrules-snapshot-2860_s.tar.gz -———————————————————————— Command line: snort_2.8.6 c D:\programs\Snort_2.8.6\snort\etc\snort.conf -r d:\users\amir\docs\darpa\training_data\week_3\monday\outside.tcpdump -l D:\users\amir\current-task\research\thesis\snort\890230 -————————————————————————— Snort.config Hi. I'm working on DARPA 1998 intrusion detection dataset. When I run snort on this dataset (outside.tcpdump file), snort don't generate complete list of alerts. It means snort start from last few hours of tcpdump file and generate alerts about this section of file and all of packets in first hours are ignored. Another problem in generatin alert is in time stamp of generated alerts. This means when I run snort on a specific day of dataset, snort insert incorrect time stamp for that alert. The configuration and command line statement and other information about my research are: Snort version: 2.8.6 Operating system: windows XP Rule version: snortrules-snapshot-2860_s.tar.gz Command line: snort_2.8.6 -c D:\programs\Snort_2.8.6\snort\etc\snort.conf -r d:\users\amir\docs\darpa\training_data\week_3\monday\outside.tcpdump -l D:\users\amir\current-task\research\thesis\snort\890230 Snort.config # Setup the network addresses you are protecting var HOME_NET any # Set up the external network addresses. Leave as "any" in most situations var EXTERNAL_NET any # List of DNS servers on your network var DNS_SERVERS $HOME_NET # List of SMTP servers on your network var SMTP_SERVERS $HOME_NET # List of web servers on your network var HTTP_SERVERS $HOME_NET # List of sql servers on your network var SQL_SERVERS $HOME_NET # List of telnet servers on your network var TELNET_SERVERS $HOME_NET # List of ssh servers on your network var SSH_SERVERS $HOME_NET # List of ports you run web servers on portvar HTTP_PORTS [80,1220,2301,3128,7777,7779,8000,8008,8028,8080,8180,8888,9999] # List of ports you want to look for SHELLCODE on. portvar SHELLCODE_PORTS !80 # List of ports you might see oracle attacks on portvar ORACLE_PORTS 1024: # List of ports you want to look for SSH connections on: portvar SSH_PORTS 22 # other variables, these should not be modified var AIM_SERVERS [64.12.24.0/23,64.12.28.0/23,64.12.161.0/24,64.12.163.0/24,64.12.200.0/24,205.188.3.0/24,205.188.5.0/24,205.188.7.0/24,205.188.9.0/24,205.188.153.0/24,205.188.179.0/24,205.188.248.0/24] var RULE_PATH ../rules var SO_RULE_PATH ../so_rules var PREPROC_RULE_PATH ../preproc_rules # Stop generic decode events: config disable_decode_alerts # Stop Alerts on experimental TCP options config disable_tcpopt_experimental_alerts # Stop Alerts on obsolete TCP options config disable_tcpopt_obsolete_alerts # Stop Alerts on T/TCP alerts config disable_tcpopt_ttcp_alerts # Stop Alerts on all other TCPOption type events: config disable_tcpopt_alerts # Stop Alerts on invalid ip options config disable_ipopt_alerts # Alert if value in length field (IP, TCP, UDP) is greater th elength of the packet # config enable_decode_oversized_alerts # Same as above, but drop packet if in Inline mode (requires enable_decode_oversized_alerts) # config enable_decode_oversized_drops # Configure IP / TCP checksum mode config checksum_mode: all config pcre_match_limit: 1500 config pcre_match_limit_recursion: 1500 # Configure the detection engine See the Snort Manual, Configuring Snort - Includes - Config config detection: search-method ac-split search-optimize max-pattern-len 20 # Configure the event queue. For more information, see README.event_queue config event_queue: max_queue 8 log 3 order_events content_length dynamicpreprocessor directory D:\programs\Snort_2.8.6\snort\lib\snort_dynamicpreprocessor dynamicengine D:\programs\Snort_2.8.6\snort\lib\snort_dynamicengine\sf_engine.dll # path to dynamic rules libraries #dynamicdetection directory /usr/local/lib/snort_dynamicrules preprocessor frag3_global: max_frags 65536 preprocessor frag3_engine: policy windows detect_anomalies overlap_limit 10 min_fragment_length 100 timeout 180 preprocessor stream5_global: max_tcp 8192, track_tcp yes, track_udp yes, track_icmp no preprocessor stream5_tcp: policy windows, detect_anomalies, require_3whs 180, \ overlap_limit 10, small_segments 3 bytes 150, timeout 180, \ ports client 21 22 23 25 42 53 79 109 110 111 113 119 135 136 137 139 143 \ 161 445 513 514 587 593 691 1433 1521 2100 3306 6665 6666 6667 6668 6669 \ 7000 32770 32771 32772 32773 32774 32775 32776 32777 32778 32779, \ ports both 80 443 465 563 636 989 992 993 994 995 1220 2301 3128 6907 7702 7777 7779 7801 7900 7901 7902 7903 7904 7905 \ 7906 7908 7909 7910 7911 7912 7913 7914 7915 7916 7917 7918 7919 7920 8000 8008 8028 8080 8180 8888 9999 preprocessor stream5_udp: timeout 180 preprocessor http_inspect: global iis_unicode_map unicode.map 1252 compress_depth 20480 decompress_depth 20480 preprocessor http_inspect_server: server default \ chunk_length 500000 \ server_flow_depth 0 \ client_flow_depth 0 \ post_depth 65495 \ oversize_dir_length 500 \ max_header_length 750 \ max_headers 100 \ ports { 80 1220 2301 3128 7777 7779 8000 8008 8028 8080 8180 8888 9999 } \ non_rfc_char { 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 } \ enable_cookie \ extended_response_inspection \ inspect_gzip \ apache_whitespace no \ ascii no \ bare_byte no \ directory no \ double_decode no \ iis_backslash no \ iis_delimiter no \ iis_unicode no \ multi_slash no \ non_strict \ u_encode yes \ webroot no preprocessor rpc_decode: 111 32770 32771 32772 32773 32774 32775 32776 32777 32778 32779 no_alert_multiple_requests no_alert_large_fragments no_alert_incomplete preprocessor bo preprocessor ftp_telnet: global inspection_type stateful encrypted_traffic no preprocessor ftp_telnet_protocol: telnet \ ayt_attack_thresh 20 \ normalize ports { 23 } \ detect_anomalies preprocessor ftp_telnet_protocol: ftp server default \ def_max_param_len 100 \ ports { 21 2100 3535 } \ telnet_cmds yes \ ignore_telnet_erase_cmds yes \ ftp_cmds { ABOR ACCT ADAT ALLO APPE AUTH CCC CDUP } \ ftp_cmds { CEL CLNT CMD CONF CWD DELE ENC EPRT } \ ftp_cmds { EPSV ESTA ESTP FEAT HELP LANG LIST LPRT } \ ftp_cmds { LPSV MACB MAIL MDTM MIC MKD MLSD MLST } \ ftp_cmds { MODE NLST NOOP OPTS PASS PASV PBSZ PORT } \ ftp_cmds { PROT PWD QUIT REIN REST RETR RMD RNFR } \ ftp_cmds { RNTO SDUP SITE SIZE SMNT STAT STOR STOU } \ ftp_cmds { STRU SYST TEST TYPE USER XCUP XCRC XCWD } \ ftp_cmds { XMAS XMD5 XMKD XPWD XRCP XRMD XRSQ XSEM } \ ftp_cmds { XSEN XSHA1 XSHA256 } \ alt_max_param_len 0 { ABOR CCC CDUP ESTA FEAT LPSV NOOP PASV PWD QUIT REIN STOU SYST XCUP XPWD } \ alt_max_param_len 200 { ALLO APPE CMD HELP NLST RETR RNFR STOR STOU XMKD } \ alt_max_param_len 256 { CWD RNTO } \ alt_max_param_len 400 { PORT } \ alt_max_param_len 512 { SIZE } \ chk_str_fmt { ACCT ADAT ALLO APPE AUTH CEL CLNT CMD } \ chk_str_fmt { CONF CWD DELE ENC EPRT EPSV ESTP HELP } \ chk_str_fmt { LANG LIST LPRT MACB MAIL MDTM MIC MKD } \ chk_str_fmt { MLSD MLST MODE NLST OPTS PASS PBSZ PORT } \ chk_str_fmt { PROT REST RETR RMD RNFR RNTO SDUP SITE } \ chk_str_fmt { SIZE SMNT STAT STOR STRU TEST TYPE USER } \ chk_str_fmt { XCRC XCWD XMAS XMD5 XMKD XRCP XRMD XRSQ } \ chk_str_fmt { XSEM XSEN XSHA1 XSHA256 } \ cmd_validity ALLO \ cmd_validity EPSV \ cmd_validity MACB \ cmd_validity MDTM \ cmd_validity MODE \ cmd_validity PORT \ cmd_validity PROT \ cmd_validity STRU \ cmd_validity TYPE preprocessor ftp_telnet_protocol: ftp client default \ max_resp_len 256 \ bounce yes \ ignore_telnet_erase_cmds yes \ telnet_cmds yes preprocessor smtp: ports { 25 465 587 691 } \ inspection_type stateful \ normalize cmds \ normalize_cmds { MAIL RCPT HELP HELO ETRN EHLO EXPN VRFY ATRN SIZE BDAT DEBUG EMAL ESAM ESND ESOM EVFY IDENT NOOP RSET SEND SAML SOML AUTH TURN DATA QUIT ONEX QUEU STARTTLS TICK TIME TURNME VERB X-EXPS X-LINK2STATE XADR XAUTH XCIR XEXCH50 XGEN XLICENSE XQUE XSTA XTRN XUSR } \ max_command_line_len 512 \ max_header_line_len 1000 \ max_response_line_len 512 \ alt_max_command_line_len 260 { MAIL } \ alt_max_command_line_len 300 { RCPT } \ alt_max_command_line_len 500 { HELP HELO ETRN EHLO } \ alt_max_command_line_len 255 { EXPN VRFY ATRN SIZE BDAT DEBUG EMAL ESAM ESND ESOM EVFY IDENT NOOP RSET } \ alt_max_command_line_len 246 { SEND SAML SOML AUTH TURN ETRN DATA RSET QUIT ONEX QUEU STARTTLS TICK TIME TURNME VERB X-EXPS X-LINK2STATE XADR XAUTH XCIR XEXCH50 XGEN XLICENSE XQUE XSTA XTRN XUSR } \ valid_cmds { MAIL RCPT HELP HELO ETRN EHLO EXPN VRFY ATRN SIZE BDAT DEBUG EMAL ESAM ESND ESOM EVFY IDENT NOOP RSET SEND SAML SOML AUTH TURN DATA QUIT ONEX QUEU STARTTLS TICK TIME TURNME VERB X-EXPS X-LINK2STATE XADR XAUTH XCIR XEXCH50 XGEN XLICENSE XQUE XSTA XTRN XUSR } \ xlink2state { enabled } preprocessor ssh: server_ports { 22 } \ autodetect \ max_client_bytes 19600 \ max_encrypted_packets 20 \ max_server_version_len 100 \ enable_respoverflow enable_ssh1crc32 \ enable_srvoverflow enable_protomismatch preprocessor dcerpc2: memcap 102400, events [co ] preprocessor dcerpc2_server: default, policy WinXP, \ detect [smb [139,445], tcp 135, udp 135, rpc-over-http-server 593], \ autodetect [tcp 1025:, udp 1025:, rpc-over-http-server 1025:], \ smb_max_chain 3 preprocessor dns: ports { 53 } enable_rdata_overflow preprocessor ssl: ports { 443 465 563 636 989 992 993 994 995 7801 7702 7900 7901 7902 7903 7904 7905 7906 6907 7908 7909 7910 7911 7912 7913 7914 7915 7916 7917 7918 7919 7920 }, trustservers, noinspect_encrypted # SDF sensitive data preprocessor. For more information see README.sensitive_data preprocessor sensitive_data: alert_threshold 25 output alert_full: alert.log output database: log, mysql, user=root password=123456 dbname=snort host=localhost include classification.config include reference.config include $RULE_PATH/local.rules include $RULE_PATH/attack-responses.rules include $RULE_PATH/backdoor.rules include $RULE_PATH/bad-traffic.rules include $RULE_PATH/chat.rules include $RULE_PATH/content-replace.rules include $RULE_PATH/ddos.rules include $RULE_PATH/dns.rules include $RULE_PATH/dos.rules include $RULE_PATH/exploit.rules include $RULE_PATH/finger.rules include $RULE_PATH/ftp.rules include $RULE_PATH/icmp.rules include $RULE_PATH/icmp-info.rules include $RULE_PATH/imap.rules include $RULE_PATH/info.rules include $RULE_PATH/misc.rules include $RULE_PATH/multimedia.rules include $RULE_PATH/mysql.rules include $RULE_PATH/netbios.rules include $RULE_PATH/nntp.rules include $RULE_PATH/oracle.rules include $RULE_PATH/other-ids.rules include $RULE_PATH/p2p.rules include $RULE_PATH/policy.rules include $RULE_PATH/pop2.rules include $RULE_PATH/pop3.rules include $RULE_PATH/rpc.rules include $RULE_PATH/rservices.rules include $RULE_PATH/scada.rules include $RULE_PATH/scan.rules include $RULE_PATH/shellcode.rules include $RULE_PATH/smtp.rules include $RULE_PATH/snmp.rules include $RULE_PATH/specific-threats.rules include $RULE_PATH/spyware-put.rules include $RULE_PATH/sql.rules include $RULE_PATH/telnet.rules include $RULE_PATH/tftp.rules include $RULE_PATH/virus.rules include $RULE_PATH/voip.rules include $RULE_PATH/web-activex.rules include $RULE_PATH/web-attacks.rules include $RULE_PATH/web-cgi.rules include $RULE_PATH/web-client.rules include $RULE_PATH/web-coldfusion.rules include $RULE_PATH/web-frontpage.rules include $RULE_PATH/web-iis.rules include $RULE_PATH/web-misc.rules include $RULE_PATH/web-php.rules include $RULE_PATH/x11.rules include threshold.conf -————————————————————————————- Can anyone help me to solve this problem? Thanks.

    Read the article

  • xslt cookbook example not working

    - by Liza dawson
    Hi I am working on this from xslt cookbook type my.xml <?xml version="1.0" encoding="UTF-8"?> <people> <person name="Al Zehtooney" age="33" sex="m" smoker="no"/> <person name="Brad York" age="38" sex="m" smoker="yes"/> <person name="Charles Xavier" age="32" sex="m" smoker="no"/> <person name="David Williams" age="33" sex="m" smoker="no"/> <person name="Edward Ulster" age="33" sex="m" smoker="yes"/> <person name="Frank Townsend" age="35" sex="m" smoker="no"/> <person name="Greg Sutter" age="40" sex="m" smoker="no"/> <person name="Harry Rogers" age="37" sex="m" smoker="no"/> <person name="John Quincy" age="43" sex="m" smoker="yes"/> <person name="Kent Peterson" age="31" sex="m" smoker="no"/> <person name="Larry Newell" age="23" sex="m" smoker="no"/> <person name="Max Milton" age="22" sex="m" smoker="no"/> <person name="Norman Lamagna" age="30" sex="m" smoker="no"/> <person name="Ollie Kensington" age="44" sex="m" smoker="no"/> <person name="John Frank" age="24" sex="m" smoker="no"/> <person name="Mary Williams" age="33" sex="f" smoker="no"/> <person name="Jane Frank" age="38" sex="f" smoker="yes"/> <person name="Jo Peterson" age="32" sex="f" smoker="no"/> <person name="Angie Frost" age="33" sex="f" smoker="no"/> <person name="Betty Bates" age="33" sex="f" smoker="no"/> <person name="Connie Date" age="35" sex="f" smoker="no"/> <person name="Donna Finster" age="20" sex="f" smoker="no"/> <person name="Esther Gates" age="37" sex="f" smoker="no"/> <person name="Fanny Hill" age="33" sex="f" smoker="yes"/> <person name="Geta Iota" age="27" sex="f" smoker="no"/> <person name="Hillary Johnson" age="22" sex="f" smoker="no"/> <person name="Ingrid Kent" age="21" sex="f" smoker="no"/> <person name="Jill Larson" age="20" sex="f" smoker="no"/> <person name="Kim Mulrooney" age="41" sex="f" smoker="no"/> <person name="Lisa Nevins" age="21" sex="f" smoker="no"/> </people> type generic-attr-to-csv.xslt <xsl:stylesheet version="1.0" xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:csv="http://www.ora.com/XSLTCookbook/namespaces/csv"> <xsl:param name="delimiter" select=" ',' "/> <xsl:output method="text" /> <xsl:strip-space elements="*"/> <xsl:template match="/"> <xsl:for-each select="$columns"> <xsl:value-of select="@name"/> <xsl:if test="position( ) != last( )"> <xsl:value-of select="$delimiter/> </xsl:if> </xsl:for-each> <xsl:text>&#xa;</xsl:text> <xsl:apply-templates/> </xsl:template> <xsl:template match="/*/*"> <xsl:variable name="row" select="."/> <xsl:for-each select="$columns"> <xsl:apply-templates select="$row/@*[local-name(.)=current( )/@attr]" mode="csv:map-value"/> <xsl:if test="position( ) != last( )"> <xsl:value-of select="$delimiter"/> </xsl:if> </xsl:for-each> <xsl:text>&#xa;</xsl:text> </xsl:template> <xsl:template match="@*" mode="map-value"> <xsl:value-of select="."/> </xsl:template> </xsl:stylesheet> type my.xsl <xsl:stylesheet version="1.0" xmlns:xsl="http://www.w3.org/1999/XSL/Transform" xmlns:csv="http://www.ora.com/XSLTCookbook/namespaces/csv"> <xsl:import href="generic-attr-to-csv.xslt"/> <!--Defines the mapping from attributes to columns --> <xsl:variable name="columns" select="document('')/*/csv:column"/> <csv:column name="Name" attr="name"/> <csv:column name="Age" attr="age"/> <csv:column name="Gender" attr="sex"/> <csv:column name="Smoker" attr="smoker"/> <!-- Handle custom attribute mappings --> <xsl:template match="@sex" mode="csv:map-value"> <xsl:choose> <xsl:when test=".='m'">male</xsl:when> <xsl:when test=".='f'">female</xsl:when> <xsl:otherwise>error</xsl:otherwise> </xsl:choose> </xsl:template> </xsl:stylesheet> using the apache xalan parser D:\Test>java org.apache.xalan.xslt.Process -in my.xml -xsl my.xsl -out my.csv [Fatal Error] generic-attr-to-csv.xslt:15:6: The value of attribute "select" associated with an element type "xsl:v alue-of" must not contain the '<' character. file:///D:/Test/generic-attr-to-csv.xslt; Line #15; Column #6; org.xml.sax.SAXParseException: The value of attribut e "select" associated with an element type "xsl:value-of" must not contain the '<' character. java.lang.NullPointerException at org.apache.xalan.transformer.TransformerImpl.createSerializationHandler(TransformerImpl.java:1171) at org.apache.xalan.transformer.TransformerImpl.createSerializationHandler(TransformerImpl.java:1060) at org.apache.xalan.transformer.TransformerImpl.transform(TransformerImpl.java:1268) at org.apache.xalan.transformer.TransformerImpl.transform(TransformerImpl.java:1251) at org.apache.xalan.xslt.Process.main(Process.java:1048) Exception in thread "main" java.lang.RuntimeException at org.apache.xalan.xslt.Process.doExit(Process.java:1155) at org.apache.xalan.xslt.Process.main(Process.java:1128) Any ideas what am i doing wrong

    Read the article

  • MonoTouch App Crashes When Returning From MFMailComposeViewController

    - by Richard Khan
    My MonoTouch Version Info: Release ID: 20401003 Git revision: 2f1746af36f421d262dcd2b0542ce86b12158f02 Build date: 2010-12-23 23:13:38+0000 The MFMailComposeViewController is displayed and works correctly as a dialog using the following code: if (MFMailComposeViewController.CanSendMail) { MFMailComposeViewController mail; mail = new MFMailComposeViewController (); mail.SetSubject ("Subject Test"); mail.SetMessageBody ("Body Test", false); mail.Finished += HandleMailFinished; this.navigationController.PresentModalViewController (mail, true); } else { new UIAlertView ("Mail Failed", "Mail Failed", null, "OK", null).Show (); } However, once the user selects Cancel | Delete Draft or Cancel | Save Draft or Send, the App throws a run-time error like the following: Stacktrace: at (wrapper managed-to-native) MonoTouch.UIKit.UIApplication.UIApplicationMain (int,string[],intptr,intptr) <0x00004 at (wrapper managed-to-native) MonoTouch.UIKit.UIApplication.UIApplicationMain (int,string[],intptr,intptr) <0x00004 at MonoTouch.UIKit.UIApplication.Main (string[],string,string) [0x00038] in /Users/plasma/Source/iphone/monotouch/UIKit/UIApplication.cs:26 at MonoTouch.UIKit.UIApplication.Main (string[]) [0x00000] in /Users/plasma/Source/iphone/monotouch/UIKit/UIApplication.cs:31 at MailDialog.Application.Main (string[]) [0x00000] in /Users/rrkhan/Projects/Sandbox/MailDialog/Main.cs:15 at (wrapper runtime-invoke) .runtime_invoke_void_object (object,intptr,intptr,intptr) Native stacktrace: 0 MailDialog 0x000be66f mono_handle_native_sigsegv + 343 1 MailDialog 0x0000e43e mono_sigsegv_signal_handler + 313 2 libSystem.B.dylib 0x903e946b _sigtramp + 43 3 ??? 0xffffffff 0x0 + 4294967295 4 MessageUI 0x01a9f6b7 -[MFMailComposeController _close] + 284 5 UIKit 0x01f682f1 -[UIActionSheet(Private) _buttonClicked:] + 258 6 UIKit 0x01be1a6e -[UIApplication sendAction:to:from:forEvent:] + 119 7 UIKit 0x01c701b5 -[UIControl sendAction:to:forEvent:] + 67 8 UIKit 0x01c72647 -[UIControl(Internal) _sendActionsForEvents:withEvent:] + 527 9 UIKit 0x01c711f4 -[UIControl touchesEnded:withEvent:] + 458 10 UIKit 0x01c060d1 -[UIWindow _sendTouchesForEvent:] + 567 11 UIKit 0x01be737a -[UIApplication sendEvent:] + 447 12 UIKit 0x01bec732 _UIApplicationHandleEvent + 7576 13 GraphicsServices 0x03eb7a36 PurpleEventCallback + 1550 14 CoreFoundation 0x00df9064 CFRUNLOOP_IS_CALLING_OUT_TO_A_SOURCE1_PERFORM_FUNCTION + 52 15 CoreFoundation 0x00d596f7 __CFRunLoopDoSource1 + 215 16 CoreFoundation 0x00d56983 __CFRunLoopRun + 979 17 CoreFoundation 0x00d56240 CFRunLoopRunSpecific + 208 18 CoreFoundation 0x00d56161 CFRunLoopRunInMode + 97 19 GraphicsServices 0x03eb6268 GSEventRunModal + 217 20 GraphicsServices 0x03eb632d GSEventRun + 115 21 UIKit 0x01bf042e UIApplicationMain + 1160 22 ??? 0x0a1e4bd9 0x0 + 169757657 23 ??? 0x0a1e4b12 0x0 + 169757458 24 ??? 0x0a1e4515 0x0 + 169755925 25 ??? 0x0a1e4451 0x0 + 169755729 26 ??? 0x0a1e44ac 0x0 + 169755820 27 MailDialog 0x0000e202 mono_jit_runtime_invoke + 1360 28 MailDialog 0x001c92af mono_runtime_invoke + 137 29 MailDialog 0x001caf6b mono_runtime_exec_main + 714 30 MailDialog 0x001ca891 mono_runtime_run_main + 812 31 MailDialog 0x00094fe8 mono_jit_exec + 200 32 MailDialog 0x0027cf05 main + 3494 33 MailDialog 0x00002ca1 _start + 208 34 MailDialog 0x00002bd0 start + 40 Debug info from gdb: warning: Could not find object file "/var/folders/Ny/NyElTwhDGD8kZMqIEeLGXE+++TI/-Tmp-//cc6F1tBs.o" - no debug information available for "template.m". warning: .o file "/Developer/MonoTouch/SDKs/MonoTouch.iphonesimulator4.2.sdk/usr/lib/libmonotouch.a(zlib-helper.x86.42.o)" more recent than executable timestamp in "/Users/rrkhan/Library/Application Support/iPhone Simulator/4.2/Applications/52AF1D24-AADA-48ED-B373-ED08E89E4985/MailDialog.app/MailDialog" warning: Could not open OSO file /Developer/MonoTouch/SDKs/MonoTouch.iphonesimulator4.2.sdk/usr/lib/libmonotouch.a(zlib-helper.x86.42.o) to scan for pubtypes for objfile /Users/rrkhan/Library/Application Support/iPhone Simulator/4.2/Applications/52AF1D24-AADA-48ED-B373-ED08E89E4985/MailDialog.app/MailDialog warning: .o file "/Developer/MonoTouch/SDKs/MonoTouch.iphonesimulator4.2.sdk/usr/lib/libmonotouch.a(monotouch-glue.x86.42.o)" more recent than executable timestamp in "/Users/rrkhan/Library/Application Support/iPhone Simulator/4.2/Applications/52AF1D24-AADA-48ED-B373-ED08E89E4985/MailDialog.app/MailDialog" warning: Could not open OSO file /Developer/MonoTouch/SDKs/MonoTouch.iphonesimulator4.2.sdk/usr/lib/libmonotouch.a(monotouch-glue.x86.42.o) to scan for pubtypes for objfile /Users/rrkhan/Library/Application Support/iPhone Simulator/4.2/Applications/52AF1D24-AADA-48ED-B373-ED08E89E4985/MailDialog.app/MailDialog warning: .o file "/Developer/MonoTouch/SDKs/MonoTouch.iphonesimulator4.2.sdk/usr/lib/libmonotouch.a(gc.x86.42.o)" more recent than executable timestamp in "/Users/rrkhan/Library/Application Support/iPhone Simulator/4.2/Applications/52AF1D24-AADA-48ED-B373-ED08E89E4985/MailDialog.app/MailDialog" warning: Could not open OSO file /Developer/MonoTouch/SDKs/MonoTouch.iphonesimulator4.2.sdk/usr/lib/libmonotouch.a(gc.x86.42.o) to scan for pubtypes for objfile /Users/rrkhan/Library/Application Support/iPhone Simulator/4.2/Applications/52AF1D24-AADA-48ED-B373-ED08E89E4985/MailDialog.app/MailDialog Error connecting stdout and stderr (127.0.0.1:10001) warning: .o file "/Developer/MonoTouch/SDKs/MonoTouch.iphonesimulator4.2.sdk/usr/lib/libmonotouch.a(monotouch-glue.x86.42.o)" more recent than executable timestamp in "/Users/rrkhan/Library/Application Support/iPhone Simulator/4.2/Applications/52AF1D24-AADA-48ED-B373-ED08E89E4985/MailDialog.app/MailDialog" warning: Couldn't open object file '/Developer/MonoTouch/SDKs/MonoTouch.iphonesimulator4.2.sdk/usr/lib/libmonotouch.a(monotouch-glue.x86.42.o)' Attaching to process 9992. Reading symbols for shared libraries . done Reading symbols for shared libraries ....................................................................................................................... done 0x9038e459 in read$UNIX2003 () 8 0x903a8a12 in __workq_kernreturn () 7 "WebThread" 0x903830fa in mach_msg_trap () 6 0x903b10a6 in __semwait_signal () 5 0x90383136 in semaphore_wait_trap () 4 0x903830fa in mach_msg_trap () 3 0x903a8a12 in __workq_kernreturn () 2 "com.apple.libdispatch-manager" 0x903a9982 in kevent () * 1 "com.apple.main-thread" 0x9038e459 in read$UNIX2003 () Thread 8 (process 9992): 0 0x903a8a12 in __workq_kernreturn () 1 0x903a8fa8 in _pthread_wqthread () 2 0x903a8bc6 in start_wqthread () Thread 7 (process 9992): 0 0x903830fa in mach_msg_trap () 1 0x90383867 in mach_msg () 2 0x00df94a6 in __CFRunLoopServiceMachPort () 3 0x00d56874 in __CFRunLoopRun () 4 0x00d56240 in CFRunLoopRunSpecific () 5 0x00d56161 in CFRunLoopRunInMode () 6 0x04f7c423 in RunWebThread () 7 0x903b085d in _pthread_start () 8 0x903b06e2 in thread_start () Thread 6 (process 9992): 0 0x903b10a6 in __semwait_signal () 1 0x903dcee5 in nanosleep$UNIX2003 () 2 0x903dce23 in usleep$UNIX2003 () 3 0x0027714c in monotouch_pump_gc () 4 0x903b085d in _pthread_start () 5 0x903b06e2 in thread_start () Thread 5 (process 9992): 0 0x90383136 in semaphore_wait_trap () 1 0x0015ae1d in finalizer_thread (unused=0x0) at ../../../../mono/metadata/gc.c:1026 2 0x002034a3 in start_wrapper (data=0x7b16ba0) at ../../../../mono/metadata/threads.c:661 3 0x002448e2 in thread_start_routine (args=0x8037e34) at ../../../../mono/io-layer/wthreads.c:286 4 0x00274357 in GC_start_routine (arg=0x6ff7f60) at ../../../libgc/pthread_support.c:1390 5 0x903b085d in _pthread_start () 6 0x903b06e2 in thread_start () Thread 4 (process 9992): 0 0x903830fa in mach_msg_trap () 1 0x90383867 in mach_msg () 2 0x0011cc46 in mach_exception_thread (arg=0x0) at ../../../../mono/mini/mini-darwin.c:138 3 0x903b085d in _pthread_start () 4 0x903b06e2 in thread_start () Thread 3 (process 9992): 0 0x903a8a12 in __workq_kernreturn () 1 0x903a8fa8 in _pthread_wqthread () 2 0x903a8bc6 in start_wqthread () Thread 2 (process 9992): 0 0x903a9982 in kevent () 1 0x903aa09c in _dispatch_mgr_invoke () 2 0x903a9559 in _dispatch_queue_invoke () 3 0x903a92fe in _dispatch_worker_thread2 () 4 0x903a8d81 in _pthread_wqthread () 5 0x903a8bc6 in start_wqthread () Thread 1 (process 9992): 0 0x9038e459 in read$UNIX2003 () 1 0x000be81f in mono_handle_native_sigsegv (signal=11, ctx=0xbfffd238) at ../../../../mono/mini/mini-exceptions.c:1826 2 0x0000e43e in mono_sigsegv_signal_handler (_dummy=10, info=0xbfffd1f8, context=0xbfffd238) at ../../../../mono/mini/mini.c:4846 3 4 0x028d6a63 in objc_msgSend () 5 0x01ad469f in func.24012 () 6 0x01a9f6b7 in -[MFMailComposeController _close] () 7 0x01f682f1 in -[UIActionSheet(Private) _buttonClicked:] () 8 0x01be1a6e in -[UIApplication sendAction:to:from:forEvent:] () 9 0x01c701b5 in -[UIControl sendAction:to:forEvent:] () 10 0x01c72647 in -[UIControl(Internal) _sendActionsForEvents:withEvent:] () 11 0x01c711f4 in -[UIControl touchesEnded:withEvent:] () 12 0x01c060d1 in -[UIWindow _sendTouchesForEvent:] () 13 0x01be737a in -[UIApplication sendEvent:] () 14 0x01bec732 in _UIApplicationHandleEvent () 15 0x03eb7a36 in PurpleEventCallback () 16 0x00df9064 in CFRUNLOOP_IS_CALLING_OUT_TO_A_SOURCE1_PERFORM_FUNCTION () 17 0x00d596f7 in __CFRunLoopDoSource1 () 18 0x00d56983 in __CFRunLoopRun () 19 0x00d56240 in CFRunLoopRunSpecific () 20 0x00d56161 in CFRunLoopRunInMode () 21 0x03eb6268 in GSEventRunModal () 22 0x03eb632d in GSEventRun () 23 0x01bf042e in UIApplicationMain () 24 0x0a1e4bd9 in ?? () 25 0x0a1e4b12 in ?? () 26 0x0a1e4515 in ?? () 27 0x0a1e4451 in ?? () 28 0x0a1e44ac in ?? () 29 0x0000e202 in mono_jit_runtime_invoke (method=0xa806e6c, obj=0x0, params=0xbfffedbc, exc=0x0) at ../../../../mono/mini/mini.c:4733 30 0x001c92af in mono_runtime_invoke (method=0xa806e6c, obj=0x0, params=0xbfffedbc, exc=0x0) at ../../../../mono/metadata/object.c:2615 31 0x001caf6b in mono_runtime_exec_main (method=0xa806e6c, args=0xa6a34e0, exc=0x0) at ../../../../mono/metadata/object.c:3581 32 0x001ca891 in mono_runtime_run_main (method=0xa806e6c, argc=0, argv=0xbfffeef4, exc=0x0) at ../../../../mono/metadata/object.c:3355 33 0x00094fe8 in mono_jit_exec (domain=0x6f8fe58, assembly=0xa200730, argc=1, argv=0xbfffeef0) at ../../../../mono/mini/driver.c:1094 34 0x0027cf05 in main () ================================================================= Got a SIGSEGV while executing native code. This usually indicates a fatal error in the mono runtime or one of the native libraries used by your application. Unhandled Exception: System.NullReferenceException: Object reference not set to an instance of an object at (wrapper managed-to-native) MonoTouch.UIKit.UIApplication:UIApplicationMain (int,string[],intptr,intptr) at MonoTouch.UIKit.UIApplication.Main (System.String[] args, System.String principalClassName, System.String delegateClassName) [0x00038] in /Users/plasma/Source/iphone/monotouch/UIKit/UIApplication.cs:26 at MonoTouch.UIKit.UIApplication.Main (System.String[] args) [0x00000] in /Users/plasma/Source/iphone/monotouch/UIKit/UIApplication.cs:31 at MailDialog.Application.Main (System.String[] args) [0x00000] in /Users/rrkhan/Projects/Sandbox/MailDialog/Main.cs:15 I have a very simple sample project illustrating the problem. I can sent you if required.

    Read the article

  • android app does not show up on my device or the emulator in eclipse

    - by Sam
    hey everyone, I have no errors in my app-code what so ever, but when i try to run in on either my cell or my emulator/the avd in eclipse i can't run it because it doesn't show up on either one. this is my console output: [2011-02-04 08:14:58 - Versuch] Uploading Versuch.apk onto device 'CB511L2WTB' [2011-02-04 08:14:58 - Versuch] Installing Versuch.apk... [2011-02-04 08:15:01 - Versuch] Success! [2011-02-04 08:15:01 - Versuch] \Versuch\bin\Versuch.apk installed on device [2011-02-04 08:15:01 - Versuch] Done! and this is my LogCat output, which tells me nothing, but you are the experts ;) 02-04 08:18:10.020: DEBUG/dalvikvm(22167): GC freed 2576 objects / 559120 bytes in 37ms 02-04 08:18:10.700: DEBUG/dalvikvm(6709): GC freed 7692 objects / 478912 bytes in 41ms 02-04 08:18:11.170: DEBUG/dalvikvm(31774): GC freed 3367 objects / 163464 bytes in 122ms 02-04 08:18:13.230: DEBUG/dalvikvm(22167): GC freed 2790 objects / 552328 bytes in 38ms 02-04 08:18:14.650: DEBUG/dalvikvm(6709): GC freed 8443 objects / 540440 bytes in 39ms 02-04 08:18:16.260: DEBUG/dalvikvm(31921): GC freed 214 objects / 9824 bytes in 216ms 02-04 08:18:16.670: DEBUG/dalvikvm(22167): GC freed 3232 objects / 561256 bytes in 40ms 02-04 08:18:18.600: DEBUG/dalvikvm(6709): GC freed 7718 objects / 481952 bytes in 39ms 02-04 08:18:19.210: DEBUG/dalvikvm(1129): GC freed 6898 objects / 275328 bytes in 109ms 02-04 08:18:19.690: DEBUG/dalvikvm(22167): GC freed 2968 objects / 571232 bytes in 39ms 02-04 08:18:21.440: DEBUG/dalvikvm(1212): GC freed 1020 objects / 49328 bytes in 395ms 02-04 08:18:22.570: DEBUG/dalvikvm(6709): GC freed 7893 objects / 495616 bytes in 40ms 02-04 08:18:23.060: DEBUG/dalvikvm(22167): GC freed 3117 objects / 561912 bytes in 41ms 02-04 08:18:25.860: DEBUG/dalvikvm(22167): GC freed 2924 objects / 558448 bytes in 36ms 02-04 08:18:26.350: DEBUG/dalvikvm(32098): GC freed 4662 objects / 495496 bytes in 290ms 02-04 08:18:26.410: DEBUG/dalvikvm(22167): GC freed 1077 objects / 130680 bytes in 33ms 02-04 08:18:27.080: DEBUG/dalvikvm(6709): GC freed 7912 objects / 485368 bytes in 40ms 02-04 08:18:28.190: DEBUG/dalvikvm(22167): GC freed 953 objects / 767272 bytes in 33ms 02-04 08:18:29.500: DEBUG/dalvikvm(1129): GC freed 6756 objects / 270480 bytes in 105ms 02-04 08:18:30.500: WARN/System.err(22536): java.lang.Exception: You must call com.mercuryintermedia.productconfiguration.initialize() first 02-04 08:18:30.670: WARN/System.err(22536): at com.mercuryintermedia.ProductConfiguration.getProductName(ProductConfiguration.java:136) 02-04 08:18:30.670: WARN/System.err(22536): at com.mercuryintermedia.api.rest.Item.getPublishingContainersItems(Item.java:15) 02-04 08:18:30.670: WARN/System.err(22536): at com.mercuryintermedia.mflow.ContainerHelper.getContainerFromServer(ContainerHelper.java:68) 02-04 08:18:30.670: WARN/System.err(22536): at com.mercuryintermedia.mflow.ContainerHelper.run(ContainerHelper.java:46) 02-04 08:18:31.090: DEBUG/dalvikvm(6709): GC freed 10545 objects / 682480 bytes in 49ms 02-04 08:18:31.120: DEBUG/dalvikvm(1813): GC freed 5970 objects / 310912 bytes in 60ms 02-04 08:18:31.320: DEBUG/dalvikvm(22167): GC freed 2468 objects / 539520 bytes in 39ms 02-04 08:18:34.110: DEBUG/dalvikvm(22167): GC freed 2879 objects / 569008 bytes in 35ms 02-04 08:18:34.920: DEBUG/dalvikvm(6709): GC freed 7029 objects / 424632 bytes in 35ms 02-04 08:18:36.150: DEBUG/dalvikvm(9060): GC freed 564 objects / 27840 bytes in 89ms 02-04 08:18:36.630: DEBUG/dalvikvm(22167): GC freed 2437 objects / 554000 bytes in 35ms 02-04 08:18:38.760: DEBUG/dalvikvm(6709): GC freed 8309 objects / 545032 bytes in 36ms 02-04 08:18:39.270: DEBUG/dalvikvm(1129): GC freed 6958 objects / 278352 bytes in 107ms 02-04 08:18:39.970: DEBUG/dalvikvm(22167): GC freed 2915 objects / 560312 bytes in 38ms 02-04 08:18:41.260: DEBUG/dalvikvm(6184): GC freed 373 objects / 26152 bytes in 205ms 02-04 08:18:42.780: DEBUG/dalvikvm(6709): GC freed 7212 objects / 447696 bytes in 36ms 02-04 08:18:43.160: DEBUG/dalvikvm(22167): GC freed 3106 objects / 561824 bytes in 39ms 02-04 08:18:46.310: DEBUG/dalvikvm(22167): GC freed 3110 objects / 564080 bytes in 45ms 02-04 08:18:46.650: DEBUG/dalvikvm(6709): GC freed 7508 objects / 468832 bytes in 36ms 02-04 08:18:48.820: DEBUG/dalvikvm(31712): GC freed 13795 objects / 828232 bytes in 203ms 02-04 08:18:49.040: DEBUG/dalvikvm(1129): GC freed 6918 objects / 276224 bytes in 109ms 02-04 08:18:49.640: DEBUG/dalvikvm(22167): GC freed 2952 objects / 562168 bytes in 37ms 02-04 08:18:50.630: DEBUG/dalvikvm(6709): GC freed 8332 objects / 549680 bytes in 35ms 02-04 08:18:52.770: DEBUG/dalvikvm(22167): GC freed 3108 objects / 563192 bytes in 37ms 02-04 08:18:54.400: DEBUG/dalvikvm(6709): GC freed 7509 objects / 469016 bytes in 35ms 02-04 08:18:55.900: DEBUG/dalvikvm(22167): GC freed 3121 objects / 572920 bytes in 38ms 02-04 08:18:58.150: DEBUG/dalvikvm(6709): GC freed 7408 objects / 465456 bytes in 35ms 02-04 08:18:58.710: DEBUG/dalvikvm(1129): GC freed 6908 objects / 276440 bytes in 107ms 02-04 08:18:59.190: DEBUG/dalvikvm(22167): GC freed 3160 objects / 563144 bytes in 38ms 02-04 08:19:02.080: DEBUG/dalvikvm(6709): GC freed 7436 objects / 468040 bytes in 36ms 02-04 08:19:02.380: DEBUG/dalvikvm(22167): GC freed 3104 objects / 557600 bytes in 39ms 02-04 08:19:05.050: DEBUG/dalvikvm(22167): GC freed 2860 objects / 570072 bytes in 35ms 02-04 08:19:05.810: DEBUG/dalvikvm(6709): GC freed 7508 objects / 469080 bytes in 35ms 02-04 08:19:06.500: DEBUG/skia(22167): --- decoder->decode returned false 02-04 08:19:07.960: DEBUG/dalvikvm(22167): GC freed 2747 objects / 520008 bytes in 36ms 02-04 08:19:08.180: DEBUG/dalvikvm(1129): GC freed 7866 objects / 317304 bytes in 107ms 02-04 08:19:09.540: DEBUG/dalvikvm(6709): GC freed 8220 objects / 539688 bytes in 36ms 02-04 08:19:10.810: DEBUG/dalvikvm(22167): GC freed 2898 objects / 596824 bytes in 37ms 02-04 08:19:13.360: DEBUG/dalvikvm(22167): GC freed 2503 objects / 398936 bytes in 35ms 02-04 08:19:13.370: INFO/dalvikvm-heap(22167): Grow heap (frag case) to 5.029MB for 570264-byte allocation 02-04 08:19:13.400: DEBUG/dalvikvm(22167): GC freed 702 objects / 24976 bytes in 31ms 02-04 08:19:13.400: DEBUG/skia(22167): --- decoder->decode returned false 02-04 08:19:13.540: DEBUG/dalvikvm(6709): GC freed 7481 objects / 466544 bytes in 36ms 02-04 08:19:15.600: DEBUG/WifiService(1129): got ACTION_DEVICE_IDLE 02-04 08:19:15.960: INFO/wpa_supplicant(2522): CTRL-EVENT-DRIVER-STATE STOPPED 02-04 08:19:15.960: VERBOSE/WifiMonitor(1129): Event [CTRL-EVENT-DRIVER-STATE STOPPED] 02-04 08:19:17.270: DEBUG/dalvikvm(22167): GC freed 2372 objects / 1266992 bytes in 36ms 02-04 08:19:17.520: DEBUG/dalvikvm(6709): GC freed 7996 objects / 519128 bytes in 37ms 02-04 08:19:18.150: DEBUG/dalvikvm(1129): GC freed 7110 objects / 285032 bytes in 108ms 02-04 08:19:20.460: DEBUG/dalvikvm(22167): GC freed 3327 objects / 565264 bytes in 36ms 02-04 08:19:21.250: DEBUG/dalvikvm(6709): GC freed 7632 objects / 486024 bytes in 37ms 02-04 08:19:26.470: DEBUG/dalvikvm(31774): GC freed 345 objects / 16160 bytes in 96ms 02-04 08:19:30.423: WARN/System.err(22536): java.lang.Exception: You must call com.mercuryintermedia.productconfiguration.initialize() first 02-04 08:19:30.423: WARN/System.err(22536): at com.mercuryintermedia.ProductConfiguration.getProductName(ProductConfiguration.java:136) 02-04 08:19:30.423: WARN/System.err(22536): at com.mercuryintermedia.api.rest.Item.getPublishingContainersItems(Item.java:15) 02-04 08:19:30.423: WARN/System.err(22536): at com.mercuryintermedia.mflow.ContainerHelper.getContainerFromServer(ContainerHelper.java:68) 02-04 08:19:30.423: WARN/System.err(22536): at com.mercuryintermedia.mflow.ContainerHelper.run(ContainerHelper.java:46) 02-04 08:20:05.280: DEBUG/dalvikvm(1813): GC freed 741 objects / 36840 bytes in 91ms 02-04 08:20:23.580: DEBUG/WifiService(1129): ACTION_BATTERY_CHANGED pluggedType: 2 02-04 08:20:30.423: WARN/System.err(22536): java.lang.Exception: You must call com.mercuryintermedia.productconfiguration.initialize() first 02-04 08:20:30.423: WARN/System.err(22536): at com.mercuryintermedia.ProductConfiguration.getProductName(ProductConfiguration.java:136) 02-04 08:20:30.423: WARN/System.err(22536): at com.mercuryintermedia.api.rest.Item.getPublishingContainersItems(Item.java:15) 02-04 08:20:30.423: WARN/System.err(22536): at com.mercuryintermedia.mflow.ContainerHelper.getContainerFromServer(ContainerHelper.java:68) 02-04 08:20:30.423: WARN/System.err(22536): at com.mercuryintermedia.mflow.ContainerHelper.run(ContainerHelper.java:46) 02-04 08:20:53.970: INFO/FastDormancyManager(1129): Fast Dormant executed. ExecuteCount:2683 NonExecuteCount:25773 I really hope you can help me.

    Read the article

  • Handling aces and finding a segfault in a blackjack program

    - by Bill Adams
    Here's what i have so far... I have yet to figure out how i'm going to handle the 11 / 1 situation with an ace, and when the player chooses an option for hit/stand, i get segfault. HELP!!! #include <stdio.h> #include <string.h> #include <stdlib.h> #include <time.h> #define DECKSIZE 52 #define VALUE 9 #define FACE 4 #define HANDSIZE 26 typedef struct { int value; char* suit; char* name; }Card; typedef struct { int value; char* suit; char* name; }dealerHand; typedef struct { int value; char* suit; char* name; }playerHand; Card cards[DECKSIZE]; dealerHand deal[HANDSIZE]; playerHand dealt[HANDSIZE]; char *faceName[]={"two","three", "four","five","six", "seven","eight","nine", "ten", "jack","queen", "king","ace"}; char *suitName[]={"spades","diamonds","clubs","hearts"}; void printDeck(){ int i; for(i=0;i<DECKSIZE;i++){ printf("%s of %s value = %d\n ",cards[i].name,cards[i].suit,cards[i].value); if((i+1)%13==0 && i!=0) printf("-------------------\n\n"); } } void shuffleDeck(){ srand(time(NULL)); int this; int that; Card temp; int c; for(c=0;c<10000;c++){ //c is the index for number of individual card shuffles should be set to c<10000 or more this=rand()%DECKSIZE; that=rand()%DECKSIZE; temp=cards[this]; cards[this]=cards[that]; cards[that]=temp; } } /*void hitStand(i,y){ // I dumped this because of a segfault i couldn't figure out. int k; printf(" Press 1 to HIT or press 2 to STAND:"); scanf("%d",k); if(k=1){ dealt[y].suit=cards[i].suit; dealt[y].name=cards[i].name; dealt[y].value=cards[i].value; y++; i++; } } */ int main(){ int suitCount=0; int faceCount=0; int i; int x; int y; int d; int p; int k; for(i=0;i<DECKSIZE;i++){ //this for statement builds the deck if(faceCount<9){ cards[i].value=faceCount+2; }else{ //assigns face cards as value 10 cards[i].value=10; } cards[i].suit=suitName[suitCount]; cards[i].name=faceName[faceCount++]; if(faceCount==13){ //this if loop increments suit count once cards[i].value=11; //all faces have been assigned, and also suitCount++; //assigns the ace as 11 faceCount=0; } //end building deck } /*printDeck(); //prints the deck in order shuffleDeck(); //shuffles the deck printDeck(); //prints the deck as shuffled This was used in testing, commented out to keep the deck hidden!*/ shuffleDeck(); x=0; y=0; for(i=0;i<4;i++){ //this for loop deals the first 4 cards, dealt[y].suit=cards[i].suit; //first card to player, second to dealer, dealt[y].name=cards[i].name; //as per standard dealing practice. dealt[y].value=cards[i].value; i++; y++; deal[x].suit=cards[i].suit; deal[x].name=cards[i].name; deal[x].value=cards[i].value; x++; } printf(" Dealer's hand is: %s of %s and XXXX of XXXX. (Second card is hidden!)\n",deal[0].name,deal[0].suit,deal[1].name,deal[1].suit); printf(" Player's hand is: %s of %s and %s of %s.\n",dealt[0].name,dealt[0].suit,dealt[1].name,dealt[1].suit); printf(" the current value of the index i=%d\n",i); //this line gave me the value of i for testing d=deal[0].value+deal[1].value; p=dealt[0].value+dealt[1].value; if(d==21){ printf(" The Dealer has Blackjack! House win!\n"); }else{ if(d>21){ printf(" The dealer is Bust! You win!\n"); }else{ if(d>17){ printf(" Press 1 to HIT or 2 to STAND"); scanf("%d",k); if(k==1){ dealt[y].suit=cards[i].suit; dealt[y].name=cards[i].name; dealt[y].value=cards[i].value; y++; i++; } }else{ if(d<17){ printf(" Dealer Hits!"); deal[x].suit=cards[i].suit; deal[x].name=cards[i].name; deal[x].value=cards[i].value; x++; i++; } } } } return 0; }

    Read the article

  • Char error C langauge

    - by Nadeem tabbaa
    i have a project for a course, i did almost everything but i have this error i dont know who to solve it... the project about doing our own shell some of them we have to write our code, others we will use the fork method.. this is the code, #include <sys/wait.h> #include <dirent.h> #include <limits.h> #include <errno.h> #include <stdlib.h> #include <string.h> #include<stdio.h> #include<fcntl.h> #include<unistd.h> #include<sys/stat.h> #include<sys/types.h> int main(int argc, char **argv) { pid_t pid; char str[21], *arg[10]; int x,status,number; system("clear"); while(1) { printf("Rshell>" ); fgets(str,21,stdin); x = 0; arg[x] = strtok(str, " \n\t"); while(arg[x]) arg[++x] = strtok(NULL, " \n\t"); if(NULL!=arg[0]) { if(strcasecmp(arg[0],"cat")==0) //done { int f=0,n; char l[1]; struct stat s; if(x!=2) { printf("Mismatch argument\n"); } /*if(access(arg[1],F_OK)) { printf("File Exist"); exit(1); } if(stat(arg[1],&s)<0) { printf("Stat ERROR"); exit(1); } if(S_ISREG(s.st_mode)<0) { printf("Not a Regular FILE"); exit(1); } if(geteuid()==s.st_uid) if(s.st_mode & S_IRUSR) f=1; else if(getegid()==s.st_gid) if(s.st_mode & S_IRGRP) f=1; else if(s.st_mode & S_IROTH) f=1; if(!f) { printf("Permission denied"); exit(1); }*/ f=open(arg[1],O_RDONLY); while((n=read(f,l,1))>0) write(1,l,n); } else if(strcasecmp(arg[0],"rm")==0) //done { if( unlink( arg[1] ) != 0 ) perror( "Error deleting file" ); else puts( "File successfully deleted" ); } else if(strcasecmp(arg[0],"rmdir")==0) //done { if( remove( arg[1] ) != 0 ) perror( "Error deleting Directory" ); else puts( "Directory successfully deleted" ); } else if(strcasecmp(arg[0],"ls")==0) //done { DIR *dir; struct dirent *dirent; char *where = NULL; //printf("x== %i\n",x); //printf("x== %s\n",arg[1]); //printf("x== %i\n",get_current_dir_name()); if (x == 1) where = get_current_dir_name(); else where = arg[1]; if (NULL == (dir = opendir(where))) { fprintf(stderr,"%d (%s) opendir %s failed\n", errno, strerror(errno), where); return 2; } while (NULL != (dirent = readdir(dir))) { printf("%s\n", dirent->d_name); } closedir(dir); } else if(strcasecmp(arg[0],"cp")==0) //not yet for Raed { FILE *from, *to; char ch; if(argc!=3) { printf("Usage: copy <source> <destination>\n"); exit(1); } /* open source file */ if((from = fopen(argv[1], "rb"))==NULL) { printf("Cannot open source file.\n"); exit(1); } /* open destination file */ if((to = fopen(argv[2], "wb"))==NULL) { printf("Cannot open destination file.\n"); exit(1); } /* copy the file */ while(!feof(from)) { ch = fgetc(from); if(ferror(from)) { printf("Error reading source file.\n"); exit(1); } if(!feof(from)) fputc(ch, to); if(ferror(to)) { printf("Error writing destination file.\n"); exit(1); } } if(fclose(from)==EOF) { printf("Error closing source file.\n"); exit(1); } if(fclose(to)==EOF) { printf("Error closing destination file.\n"); exit(1); } } else if(strcasecmp(arg[0],"mv")==0)//done { if( rename(arg[1],arg[2]) != 0 ) perror( "Error moving file" ); else puts( "File successfully moved" ); } else if(strcasecmp(arg[0],"hi")==0)//done { printf("hello\n"); } else if(strcasecmp(arg[0],"exit")==0) // done { return 0; } else if(strcasecmp(arg[0],"sleep")==0) // done { if(x==1) printf("plz enter the # seconds to sleep\n"); else sleep(atoi(arg[1])); } else if(strcmp(arg[0],"history")==0) // not done { FILE *infile; //char fname[40]; char line[100]; int lcount; ///* Read in the filename */ //printf("Enter the name of a ascii file: "); //fgets(History.txt, sizeof(fname), stdin); /* Open the file. If NULL is returned there was an error */ if((infile = fopen("History.txt", "r")) == NULL) { printf("Error Opening File.\n"); exit(1); } while( fgets(line, sizeof(line), infile) != NULL ) { /* Get each line from the infile */ lcount++; /* print the line number and data */ printf("Line %d: %s", lcount, line); } fclose(infile); /* Close the file */ writeHistory(arg); //write to txt file every new executed command //read from the file once the history command been called //if a command called not for the first time then just replace it to the end of the file } else if(strncmp(arg[0],"@",1)==0) // not done { //scripting files // read from the file command by command and executing them } else if(strcmp(arg[0],"type")==0) //not done { //if(x==1) //printf("plz enter the argument\n"); //else //type((arg[1])); } else { pid = fork( ); if (pid == 0) { execlp(arg[0], arg[0], arg[1], arg[2], NULL); printf ("EXEC Failed\n"); } else { wait(&status); if(strcmp(arg[0],"clear")!=0) { printf("status %04X\n",status); if(WIFEXITED(status)) printf("Normal termination, exit code %d\n", WEXITSTATUS(status)); else printf("Abnormal termination\n"); } } } } } } void writeHistory(char *arg[]) { FILE *file; file = fopen("History.txt","a+"); /* apend file (add text to a file or create a file if it does not exist.*/ int i =0; while(strcasecmp(arg[0],NULL)==0) { fprintf(file,"%s ",arg[i]); /*writes*/ } fprintf(file,"\n"); /*new line*/ fclose(file); /*done!*/ getchar(); /* pause and wait for key */ //return 0; } the thing is when i compile the code, this what it gives me /home/ugics/st255375/ICS431Labs/Project/Rshell.c: At top level: /home/ugics/st255375/ICS431Labs/Project/Rshell.c:264: warning: conflicting types for ‘writeHistory’ /home/ugics/st255375/ICS431Labs/Project/Rshell.c:217: note: previous implicit declaration of ‘writeHistory’ was here can any one help me??? thanks

    Read the article

  • ANSI C blackjack assignment, linux GCC compiler, i'm stuck...

    - by Bill Adams
    Here's what i have so far... I have yet to figure out how i'm going to handle the 11 / 1 situation with an ace, and when the player chooses an option for hit/stand, i get segfault. HELP!!! #include <stdio.h> #include <string.h> #include <stdlib.h> #include <time.h> #define DECKSIZE 52 #define VALUE 9 #define FACE 4 #define HANDSIZE 26 typedef struct { int value; char* suit; char* name; }Card; typedef struct { int value; char* suit; char* name; }dealerHand; typedef struct { int value; char* suit; char* name; }playerHand; Card cards[DECKSIZE]; dealerHand deal[HANDSIZE]; playerHand dealt[HANDSIZE]; char *faceName[]={"two","three", "four","five","six", "seven","eight","nine", "ten", "jack","queen", "king","ace"}; char *suitName[]={"spades","diamonds","clubs","hearts"}; void printDeck(){ int i; for(i=0;i<DECKSIZE;i++){ printf("%s of %s value = %d\n ",cards[i].name,cards[i].suit,cards[i].value); if((i+1)%13==0 && i!=0) printf("-------------------\n\n"); } } void shuffleDeck(){ srand(time(NULL)); int this; int that; Card temp; int c; for(c=0;c<10000;c++){ //c is the index for number of individual card shuffles should be set to c<10000 or more this=rand()%DECKSIZE; that=rand()%DECKSIZE; temp=cards[this]; cards[this]=cards[that]; cards[that]=temp; } } /*void hitStand(i,y){ // I dumped this because of a segfault i couldn't figure out. int k; printf(" Press 1 to HIT or press 2 to STAND:"); scanf("%d",k); if(k=1){ dealt[y].suit=cards[i].suit; dealt[y].name=cards[i].name; dealt[y].value=cards[i].value; y++; i++; } } */ int main(){ int suitCount=0; int faceCount=0; int i; int x; int y; int d; int p; int k; for(i=0;i<DECKSIZE;i++){ //this for statement builds the deck if(faceCount<9){ cards[i].value=faceCount+2; }else{ //assigns face cards as value 10 cards[i].value=10; } cards[i].suit=suitName[suitCount]; cards[i].name=faceName[faceCount++]; if(faceCount==13){ //this if loop increments suit count once cards[i].value=11; //all faces have been assigned, and also suitCount++; //assigns the ace as 11 faceCount=0; } //end building deck } /*printDeck(); //prints the deck in order shuffleDeck(); //shuffles the deck printDeck(); //prints the deck as shuffled This was used in testing, commented out to keep the deck hidden!*/ shuffleDeck(); x=0; y=0; for(i=0;i<4;i++){ //this for loop deals the first 4 cards, dealt[y].suit=cards[i].suit; //first card to player, second to dealer, dealt[y].name=cards[i].name; //as per standard dealing practice. dealt[y].value=cards[i].value; i++; y++; deal[x].suit=cards[i].suit; deal[x].name=cards[i].name; deal[x].value=cards[i].value; x++; } printf(" Dealer's hand is: %s of %s and XXXX of XXXX. (Second card is hidden!)\n",deal[0].name,deal[0].suit,deal[1].name,deal[1].suit); printf(" Player's hand is: %s of %s and %s of %s.\n",dealt[0].name,dealt[0].suit,dealt[1].name,dealt[1].suit); printf(" the current value of the index i=%d\n",i); //this line gave me the value of i for testing d=deal[0].value+deal[1].value; p=dealt[0].value+dealt[1].value; if(d==21){ printf(" The Dealer has Blackjack! House win!\n"); }else{ if(d>21){ printf(" The dealer is Bust! You win!\n"); }else{ if(d>17){ printf(" Press 1 to HIT or 2 to STAND"); scanf("%d",k); if(k==1){ dealt[y].suit=cards[i].suit; dealt[y].name=cards[i].name; dealt[y].value=cards[i].value; y++; i++; } }else{ if(d<17){ printf(" Dealer Hits!"); deal[x].suit=cards[i].suit; deal[x].name=cards[i].name; deal[x].value=cards[i].value; x++; i++; } } } } return 0; }

    Read the article

< Previous Page | 91 92 93 94 95 96 97 98 99 100 101 102  | Next Page >