Search Results

Search found 2798 results on 112 pages for 'ftp'.

Page 96/112 | < Previous Page | 92 93 94 95 96 97 98 99 100 101 102 103  | Next Page >

• Cisco ASA: How to route PPPoE-assigned subnet?

  - by Martijn Heemels

  We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

  Read the article

• mrepo and grouplist/groupinstall?, mrepo not working as expected with group

  - by user52874

  All, I'm trying to set up mrepo so we can have internal repositories. After quite the slog, things seem to be working as expected EXCEPT for groups. From man createrepo: EXAMPLES Here is an example of a repository with a groups file. Note that the groups file should be in the same directory as the rpm packages (i.e. /path/to/rpms/comps.xml). createrepo -g comps.xml /path/to/rpms So here's what I'm doing: wget -c http://ftp.scientificlinux.org/linux/scientific/6/x86_64/os/repodata/comps-sl6-x86_64.xml cp comps-sl6-x86_64.xml /var/mrepo/SL6-x86_64/os/Packages/comps-sl6-x86_64.xml createrepo -g comps-sl6-x86_64.xml /var/mrepo/SL6-x86_64/os/Packages/ lots of output, no apparent errors or warnings BUT.. from a client: yum grouplist Loaded plugins: refresh-packagekit Setting up Group Process Error: No group data available for configured repositories Here's /etc/mrepo.conf: ### Configuration file for mrepo ### The [main] section allows to override mrepo's default settings ### The mrepo-example.conf gives an overview of all the possible settings [main] srcdir = /var/mrepo wwwdir = /var/www/mrepo confdir = /etc/mrepo.conf.d arch = x86_64 mailto = root@localhost smtp-server = localhost pxelinux = /usr/lib/syslinux/pxelinux.0 tftpdir = /tftpboot #rhnlogin = username:password ### Any other section is considered a definition for a distribution ### You can put distribution sections in /etc/mrepo.conf.d ### Examples can be found in the documentation. Here's /etc/mrepo.conf.d/sl6.mrepo: ### Scientific Linux 6 [SL6] name = Scientific Linux 6 release = 6 arch = x86_64 metadata = repomd repoview os = rsync://rsync.scientificlinux.org/scientific/$release/$arch/os/ updates = rsync://rsync.scientificlinux.org/scientific/$release/$arch/updates/ security = rsync://rsync.scientificlinux.org/scientific/$release/$arch/updates/security/ fastbugs = rsync://rsync.scientificlinux.org/scientific/$release/$arch/updates/fastbugs/

  Read the article

• How to add URL's to wiki (MediaWiki) powered documentation?

  - by Ian Boyd

  We have an internal company wiki. The wiki engine being used is MediaWiki, the wiki engine that runs Wikipedia. Some of it contains IT stuff. One of the things i want want to have are hyperlinks to the various virtual machines. An example of a command, as it needs to run, is: vmrc://solo.avatopia.com:5901/Windows 2000 Server My first thought was to convert the URL into a link: [vmrc://solo.avatopia.com:5901/Windows 2000 Server] But the content renders literally as above: with the square brackets and all. Testing with other URL protocols: [http://solo.avatopia.com] [ftp://solo.avatopia.com] [ldap://solo.avatopia.com] [vmrc://solo.avatopia.com] Only the first two work, and are converted to hyperlinks. The other two remain as liternal text. How can i add URLs to MediaWiki powered documentation? Original Question We have an internal company wiki. The wiki engine being used is MediaWiki, the wiki engine that runs Wikipedia. Some of it contains IT stuff. One of the things i want want to have are hyperlinks to the various virtual machines. An example of a command, as it needs to run, is: \\solo\VMRC Client\vmrc.exe solo.avatopia.com:5901/Windows 2000 Server If launching from a command prompt, you have to quote the spaces: C:\>"\\solo\VMRC Client\vmrc.exe" solo.avatopia.com:5901/"Windows 2000 Server" My first thought in converting the above for use on our wiki-site, is to simply HTML-ify it: file://\\solo\VMRC Client\vmrc.exe solo.avatopia.com:5901/&quot;Windows 2000 Server&quot; but MediaWiki only converts file://\solo\VMRC to a hyperlink, the remainder is text. i've tried other random things, including enclosing the URL in square brackets. What is the correct answer? i don't want to happen to randomly stumble on some format that happens to work today, and breaks in the future.

  Read the article

• How to edit files directly on webdav in windows.

  - by phazei

  I have a webDAV setup with the cPanel webdisk. I can connect to it through NetHood and I can drag and drop files to/from there. What I can't do is simply edit any of the files directly. I need to copy it somewhere else, edit it, then copy it back. That's essentially what is needed with ftp, though smart clients will monitor the file, making it easier than webDAV in the current state I'm using it in. I was under the impression that webdav was supposed to let me work on the files as if it were a local drive. But nothing can actually open the files. How can I go about bringing more functionality around to it? Or is this as good as it gets? I have tried 'net use q:\ https://myserver.com:2078' and 'net use q:\ '\myserver.com@SSL:2078\' but neither work and only throws: "System error 67 has occurred. The network name cannot be found." I ultimately want to use TortiseSVN with the webDAV so I can have my working copy running on the server.

  Read the article

• PHP - Centos OpenSSL error

  - by mabbs

  i'm currently having a problem with OpenSSL on my Centos 6.5 Server. it ran perfectly fine until sunday. and i checked the error_log and i saw this error in the log PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib64/php/modules/openssl.so' - /usr/lib64/php/modules/openssl.so: cannot open shared object file: No such file or directory in Unknown on line 0 i tried phpinfo(); and i found that openssl is enabled i tried php -m it returned [PHP Modules] bz2 calendar Core ctype curl date dom ereg exif fileinfo filter ftp gd gettext gmp hash iconv interbase json libxml mbstring mcrypt memcache mysql mysqli openssl pcntl pcre PDO PDO_Firebird pdo_mysql pdo_sqlite Phar pspell readline Reflection session shmop SimpleXML snmp sockets SPL sqlite3 standard tokenizer wddx xml xmlreader xmlrpc xmlwriter xsl zip zlib UPDATE this is what i got from rpm -qa | grep php just like what Mike Suggested php-php-gettext-1.0.11-3.el6.noarch php-mcrypt-5.3.3-3.el6.x86_64 php-interbase-5.3.3-3.el6.x86_64 php-pdo-5.3.3-27.el6_5.1.x86_64 php-5.3.3-27.el6_5.1.x86_64 php-mysql-5.3.3-27.el6_5.1.x86_64 php-snmp-5.3.3-27.el6_5.1.x86_64 php-gd-5.3.3-27.el6_5.1.x86_64 php-xml-5.3.3-27.el6_5.1.x86_64 php-pear-1.9.4-4.el6.noarch php-pecl-memcache-3.0.5-4.el6.x86_64 phpMyAdmin-3.5.8.2-1.el6.noarch php-common-5.3.3-27.el6_5.1.x86_64 php-cli-5.3.3-27.el6_5.1.x86_64 php-devel-5.3.3-27.el6_5.1.x86_64 php-mbstring-5.3.3-27.el6_5.1.x86_64 php-xmlrpc-5.3.3-27.el6_5.1.x86_64 php-pspell-5.3.3-27.el6_5.1.x86_64

  Read the article

• Cannot access host from a virtualbox guest using bridged adapter

  - by David Dai

  I have a windows 7 host with firewall turned off. And I have a windowsXP guest running on Virtualbox 4.2.4r81684. In my windowsXP guest I tried to connect to the FTP server on my host machine(which used to work well) but it didn't work. I tried to ping my host machine, but it didn't work either. Then I tried to ping my guest from host, it worked well. my guest ip is :192.168.1.95 my host ip is : 192.168.1.9 route table on guest machine is this: C:\Documents and Settings\wenlong>route PRINT =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...08 00 27 66 54 6c ...... AMD PCNET Family PCI Ethernet Adapter #2 - Packe t Scheduler Miniport =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.95 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.1.0 255.255.255.0 192.168.1.95 192.168.1.95 20 192.168.1.95 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.1.255 255.255.255.255 192.168.1.95 192.168.1.95 20 224.0.0.0 240.0.0.0 192.168.1.95 192.168.1.95 20 255.255.255.255 255.255.255.255 192.168.1.95 192.168.1.95 1 Default Gateway: 192.168.1.1 =========================================================================== Persistent Routes: None arp cache is this: C:\Documents and Settings\wenlong>arp -a Interface: 192.168.1.95 --- 0x2 Internet Address Physical Address Type 192.168.1.1 00-26-f2-60-3c-04 dynamic 192.168.1.9 90-e6-ba-c2-90-2f dynamic It's strange because there was no problem days before and I didn't make any changes to the setting. could anybody help? PS. the guest can communicate with other machines in the LAN(for example 192.168.1.114) ok. it just cannot connect to the host machine.

  Read the article

• Compile php 5.3 ldap extension

  - by toups

  So trying to follow the very un-descriptive guide at my webhost for compiling a new php extension: **Compiling PHP 5.3 extensions You can also compile and load your own extensions. Here's how:** 1. Download and unpack the extension (from PECL, for instance). 2. If the extension is already compiled (most binary PHP loaders will be, for instance), skip to step 6. 3. /usr/local/php53/bin/phpize 4. ./configure --with-php-config=/usr/local/php53/bin/php-config 5. make 6. Copy the module to your .php/5.3/ directory. 7. Assuming your user is called "username" and your module is named "mymodule.so", add the following to your .php/5.3/phprc: extension = /home/username/.php/5.3/mymodule.so Downloaded Openldap stable release online, uploaded the unpacked gzip via ftp to my server, did step 3, 4, 5. Now on step 6 is says "copy the module...". My question is where is the module for me to copy? Sorry if it's obvious and I'm not seeing it; first time compiling a php extension :O

  Read the article

• "Unable to initialize module" fileinfo php-pecl-Fileinfo.x86_64

  - by Myers Network

  I have a brand new server server that I am trying to get setup up. This is a 64 bit machine that I can not install "fileinfo" or "memcache". I have uninstalled these and reinstalled them using yum and pecl with no luck. Yum install fine "no error" but then get error when running php. pecl from what I can tell is only installing 32bit. Does not put anything in the lib64 directory. Here is my output from php -v: PHP Warning: PHP Startup: fileinfo: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 PHP Warning: PHP Startup: memcache: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 PHP 5.2.14 (cli) (built: Aug 12 2010 16:03:48) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.2.0, Copyright (c) 1998-2010 Zend Technologies Here is some other system info incase you need it uname: Linux server.actham.us 2.6.18-194.26.1.el5 #1 SMP Tue Nov 9 12:54:20 EST 2010 x86_64 x86_64 x86_64 GNU/Linux php -m: PHP Warning: PHP Startup: fileinfo: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 PHP Warning: PHP Startup: memcache: Unable to initialize module Module compiled with module API=20050922, debug=0, thread-safety=0 PHP compiled with module API=20060613, debug=0, thread-safety=0 These options need to match in Unknown on line 0 [PHP Modules] bz2 calendar ctype curl date dbase dom exif filter ftp gd gettext gmp hash iconv imap json ldap libxml mbstring mcrypt mysql mysqli openssl pcntl pcre PDO pdo_mysql pdo_sqlite readline Reflection session shmop SimpleXML sockets SPL standard tokenizer wddx xml xmlreader xmlrpc xmlwriter xsl zip zlib [Zend Modules] Any help would be greatly appreciated, thanks....

  Read the article

• Unable to Access Localhost after starting Xampp

  - by user7370

  OS: Windows XP Professional, SP 2. Few days back i had xampplite 1.7.1 installed and was able to access localhost and phpmyadmin through browser...... Today it suddenly stopped working. In firefox after i type http://localhost/ nothing happens, just blank white screen. I removed all the files in xampplite folders and re-installed ver 1.7.1 again, it's of no use. Then i installed xampplite 1.7.2 (latest), which i had downloaded from xampp website, again it's of no use. Apache and MySql are running though. I tried using locally installing wordpress, as i have a theme ready and want to convert that design to wordpress, test it and start using it online. Running 'Port-check' on xampp control panel showed this -- RESULT ------ Service -- -- Port -- -- Status -- --------------------------------------------------- Apache (HTTP) -- 80 -- C:\xampplite\apache\bin\httpd.exe Apache (WebDAV) -- 81 -- free Apache (HTTPS) -- 443 -- C:\xampplite\apache\bin\httpd.exe MySQL -- 3306 -- C:\xampplite\mysql\bin\mysqld.exe FileZilla (FTP) -- 21 -- free FileZilla (Admin) -- 14147 -- free Mercury (SMTP) -- 25 -- free Mercury (POP3) -- 110 -- free Mercury (IMAP) -- 143 -- free Mercury (HTTP) -- 2224 -- free Mercury (Finger) -- 79 -- free Mercury (PH) -- 105 -- free Mercury (PopPass) -- 106 -- free Tomcat (AJP/1.3) -- 8009 -- free Tomcat (HTTP) -- 8080 -- free --------------------------------------------- I also Have skype installed but it's not using 'Port 80' (as i have read, this was the issue, but checked under skype option the port is 65013). And when i run file:///C:/xampp/htdocs/index.php - it shows "Something is wrong with the XAMPP installation :-( " Please help with this problem. thanks Sharath kumar

  Read the article

• Ubuntu Server: Networking fails with MODPROBE option in /etc/network/interfaces ... ??

  - by neezer

  For some reason (which I haven't been able to determine yet), yesterday morning the networking service on our web server (running Ubuntu 8.04.2 LTS -- hardy) wouldn't start, and our website went down. I noticed the following error message when trying to restart it: * Reconfiguring network interfaces... /etc/network/interfaces:6: option with empty value ifup: couldn't read interfaces file "/etc/network/interfaces" ...fail! Line 6 in the /etc/network/interfaces file concerned a MODPROBE command, which (I believe) loaded in the ip_conntrack_ftp module so that I could use PASV on my FTP server (vsftpd): (breaking modprobe commands commented out below) # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or # /usr/share/doc/ifupdown/examples for more information. # The loopback network interface auto lo iface lo inet loopback #MODPROBE=/sbin/modprobe #$MODPROBE ip_conntrack_ftp pre-up iptables-restore < /etc/iptables.up.rules # The primary network interface # Uncomment this and configure after the system has booted for the first time auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask 255.255.255.0 gateway xxx.xxx.xxx.1 dns-nameservers xxx.xxx.xxx.4 xxx.xxx.xxx.5 I've verified that there is a file in /sbin called modprobe. Like I said earlier, this setup had been working flawlessly until yesterday morning (though my bosses say that the site actually went down the previous night at 11 PM EST). Can anyone shed some light on (A) why this broke, and (B) how can I re-enable the ip_conntrack_ftp module?

  Read the article

• Ruby 1.9.3 - Bundler - Graylog2

  - by Arenstar

  im having a strange problem with bundler. Using ruby 1.8 the following works fine however not with 1.9 it always results in Could not find rake-0.9.2.2 in any of the sources Run `bundle install` to install missing gems. i dont understand why, but it functions correctly with rvm. I can not however use rvm, this is not a solution to my problem Install Ruby cd /usr/local/src wget http://ftp.ruby-lang.org/pub/ruby/1.9/ruby-1.9.3-p194.tar.gz tar xzf ruby-1.9.3-p194.tar.gz && cd ruby-1.9.3-p194 ./configure --prefix=/opt/lp/ruby-1.9.3-test make all && make install Install Graylog cd /usr/local/src wget https://github.com/downloads/Graylog2/graylog2-web-interface/graylog2-web-interface-0.9.6p1.tar.gz tar xzf graylog2-web-interface-0.9.6p1.tar.gz cd graylog2-web-interface-0.9.6p1 Setup Graylog cd /usr/local/src/graylog2-web-interface-0.9.6p1 sed -i "3 i gem 'thin', '~> 1.3.1'" Gemfile /opt/lp/ruby-1.9.3-test/bin/gem install bundle /opt/lp/ruby-1.9.3-test/bin/bundle install --path vendor/bundle --binstubs Begin the Test cd /usr/local/src/graylog2-web-interface-0.9.6p1 /opt/lp/ruby-1.9.3/bin/bundle exec bin/rake #Could not find rake-0.9.2.2 in any of the sources #Run `bundle install` to install missing gems. cd /usr/local/src/graylog2-web-interface-0.9.6p1 /opt/lp/ruby-1.9.3/bin/bundle exec bin/thin -e production -S test.sock -c . -R config.ru start #Could not find rake-0.9.2.2 in any of the sources #Run `bundle install` to install missing gems. Where am i going wrong?

  Read the article

• Multiple PHP SAPI configuration

  - by DTest

  I'm trying to build PHP for use as an apache shared module --with-apxs2 but also with the 'php-cgi' binary (fastcgi) on Mac OSX 10.6. I'm using this ./configure : /configure --prefix=/usr/local/PHP \ --with-apxs2=/usr/local/apache/bin/apxs \ --disable-ipv6 \ --enable-cgi \ --with-curl \ --with-mysqli=/usr/local/mysql/bin/mysql_config \ --with-openssl=/usr \ --enable-ftp \ --enable-shared \ --enable-soap \ --enable-sockets \ --enable-zip \ --with-zlib-dir It builds the apache php5.so module just fine, but in /usr/local/PHP/bin, there is no php-cgi file. If I build it without the --with-apxs2 option (and indeed, I don't even need the --enable-cgi option) the php-cgi file gets built with no problems. Background on my setup: PHP 5.3.4, Apache 2.2.14, Mac OSX 10.6, Tomcat with JavaBridge (which is why I need the php-cgi file) Without the apxs2 option, /usr/local/php/bin/php -v produces: PHP 5.3.4 (cli) (built: Dec 21 2010 21:35:14) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2010 Zend Technologies and /usr/local/php/bin/php-cgi -v produces: PHP 5.3.4 (cgi-fcgi) (built: Dec 21 2010 21:35:12) Copyright (c) 1997-2010 The PHP Group Zend Engine v2.3.0, Copyright (c) 1998-2010 Zend Technologies My question is, what am I not understanding with php SAPIs that won't allow the building of the two modules at the same time? Also, can I build it --with-apxs2 the first time, then make clean and rebuild in the same PHP directory /usr/local/php for the php files without issue?

  Read the article

• Mac compatible Web-Development Tools

  - by Derek Adair

  Hi, I'm looking for any Mac compatibile development tools that are tried and tested. I'm quite sick of my MySQL query browser crashing... And i'm sure there is probably better software out there anyways... At the moment my focus is dedicated to application development using PHP/MySQL/Ajax. (although, I will be learning ActionScript/Flex shortly). Here are the apps I regularly use and a general idea of the environment I work in: Hosting - localhost: Mamp Production: Amazon EC2 IDE - Coda: PHP/Mysql/Javascript Mysql - PHPMyAdmin MySQL query browser FTP - Coda FileZilla X11 is used for connecting to my production environment I am mainly looking for... -tools that will help me better manage (create, edit... whatever) databases. -Version control. This is huge as I'm working with a team of three other developers (we reeeeeeaaally need to standardize our environments..) Although any cool little tools to make my job easier are always a plus! I am unable to insert more than one link as I'm not rated on this forum.

  Read the article

• Is there any limit to AIX 5.3 pipe size ?

  - by snowflake

  Hello, I'm in trouble while performing cat/tail/head operation on large files on Aix 5.3. When asking for a cat of several 1Go file redirected to another one: cat file1 file2 file3 > outputfile The outputfile is limited to 2Go (cat: output error and result file is 2147483647 bytes) Filesystem is jfs2. I successfully uploaded through ftp 10Go files on the filesystem without problem. I found nothing relevant in etc/security/limits: default: fsize = -1 core = 2097151 cpu = -1 data = 262144 rss = 65536 stack = 65536 nofiles = 20000 ulimit -a core file size (blocks) unlimited data seg size (kbytes) 245759 file size (blocks) unlimited max memory size (kbytes) unlimited open files 2000 pipe size (512 bytes) 64 stack size (kbytes) 32768 cpu time (seconds) unlimited max user processes 2048 virtual memory (kbytes) 278527 The problem does not occur on another AIX 5.3 server, I'm just looking for a different configuration that might be the source of the problem. /etc/security/limits on the server without the problem: default: fsize = -1 core = 2097151 cpu = -1 data = 262144 rss = 65536 stack = 65536 nofiles = 20000 ulimit -a on the server without the problem: core file size (blocks, -c) 1048575 data seg size (kbytes, -d) 131072 file size (blocks, -f) unlimited max memory size (kbytes, -m) 32768 open files (-n) 20000 pipe size (512 bytes, -p) 64 stack size (kbytes, -s) 32768 cpu time (seconds, -t) unlimited max user processes (-u) 262144 virtual memory (kbytes, -v) unlimited

  Read the article

• File download speed issue over a dedicated fibre link

  - by nixnotwin

  My ISP has installed a fibre based dedicated internet connection at the place where I work. In the beginning the connection terminated at one of the ISP's core routers. It resulted in a strange issue. Eventhough the assigned speed was 5mbps, when tests were done by downloading large files over http and ftp from multiple locations, the speed never went above 2mbps. But bittorrent downloads reached 5mbps. Even file download from the ISP servers were fine. So, at the ISP our link was attached directly to their edge router. After this file downloads from high bandwidth servers, like Google and MS, reached the 5 mbps limit. Sometimes the speed would fall down below 2 mbps and suddenly it will go up to the 5 mbps limit ( it keeps on happening during any single file download). But other downloads like ubuntu apt repositories still struggle to go above 2 mbps. The engineers at the ISP have not been able to sort out the issue. After they moved us to their edge router instead of giving us 8 public ip's, they just gave 4 ip's. When we enquired about it, they told us that giving more ip's would result in arp overload at their edge router. But somehow I was able to convince them to give us the 8 ip's which we wanted. But the file download issue has remained. What might be the reason for files from different location getting downloaded with different speeds, that too with heavy fluctuation in speeds? I have downloaded files from same url's from a connection belonging to another smaller ISP, and the speeds were fine and reached full 5 mbps limit.

  Read the article

• Caused by: java.net.SocketException: Software caused connection abort: socket write error

  - by jrishere

  I running JSP on Oracle 11g, Weblogic 10.3.4. I have 2 managed server and a oracle admin server installed. I am encountering an error where intermittently the log file of the 2 managed server and admin server will show java.net.SocketException: Software caused connection abort: socket write error. The application can run for 2 days without showing this error or it can show up a few times in a day. The server load are similar everday. When this error is been encountered, the server will just stop accepting connections and will not be able to access the application. Even if I try to access the application through localhost, I will not be able to access the JSP pages and a 503 http status is shown but then I am able to access the static HTML page. I will not be able to access the Oracle 11g Weblogic admin console page. When I take a look at admin server log, it shows that the managed servers are disconnected from the admin server and vice versa. Magically the application is able to recover by its own and the application is able to access again or I need to restart the server as restarting the service of the application does not work. The FTP connections that the application is connected to are closed as well. I am able to ping to telnet to the server port. The event log doesn't seem to be leaving any information. We did run wireshark to see the packet traffic and it seems that the application port is sending a RST, ACK packet to the load balancer. Any kind help will greatly be appreciated. Should you need more info, feel free to ask me. Thanks in advance.

  Read the article

• dnssec zonesigner ignoring out-of-zone data

  - by jordi12100

  I am trying to configure DNSSec with BIND9 on CentOS 6.4 running DirectAdmin control panel. I am using this tutorial to make it work: https://www.dnssec-tools.org/wiki/index.php/Zonesigner But I can't get it work... When I run this command: zonesigner --genkeys jordikroon.nl.db jordikroon.nl.db.signed I get this error: jordikroon.nl.db:17: ignoring out-of-zone data (jordikroon.nl) jordikroon.nl.db:18: ignoring out-of-zone data (jordikroon.nl) jordikroon.nl.db:22: ignoring out-of-zone data (jordikroon.nl) jordikroon.nl.db:29: ignoring out-of-zone data (jordikroon.nl) jordikroon.nl.db:33: ignoring out-of-zone data (jordikroon.nl) zone jordikroon.nl.db/IN: has no NS records zone jordikroon.nl.db/IN: not loaded due to errors. I can't find anything on the web about this error. This is my zone db file: $TTL 14400 @ IN SOA ns1.ghservers.org. hostmaster.jordikroon.nl. ( 2013090703 14400 3600 1209600 86400 ) jordikroon.nl. 14400 IN NS ns1.ghservers.org. jordikroon.nl. 14400 IN NS ns2.ghservers.org. cp 14400 IN A 85.17.32.228 ftp 14400 IN A 85.17.32.228 jordikroon.nl. 14400 IN A 85.17.32.228 localhost 14400 IN A 127.0.0.1 mail 14400 IN A 85.17.32.228 pop 14400 IN A 85.17.32.228 smtp 14400 IN A 85.17.32.228 www 14400 IN A 85.17.32.228 jordikroon.nl. 14400 IN MX 10 mail jordikroon.nl. 14400 IN TXT "v=spf1 a mx ip4:85.17.32.228 ~all" localhost 14400 IN AAAA ::1 How do I have to fix this? All IN keywords are being ignored. Any help is welcome:-)

  Read the article

• Enable Soap for PHP 5.5.x on CentOS 6.5

  - by Chris Mancini

  Unfortunately I have to support soap on my server for the Fedex webservice. I recompiled PHP enabling support and it works via CLI but not PHP-fpm. They both point to the same ini file and both show the module loaded, but only CLI shows the configuration values. Output of php -i | grep -i soap Configuration File (php.ini) Path => /usr/local/etc Loaded Configuration File => /usr/local/etc/php.ini Configure Command => './configure' '--prefix=/usr/local' '--with-config-file-path=/usr/local/etc' '--with-config-file-scan-dir=/usr/local/etc/php_user/' '--enable-fpm' '--enable-ftp' '--enable-libxml' '--enable-mbstring' '--enable-pdo' '--enable-soap' '--enable-sockets=shared' '--enable-zip' '--with-curl' '--with-fpm-group=nginx' '--with-fpm-user=nginx' '--with-freetype-dir=/usr/lib64/' '--with-gd' '--with-jpeg-dir=/usr/lib64/' '--with-libdir=lib64' '--with-mcrypt' '--with-openssl' '--with-pdo-mysql' '--with-pear' '--with-readline' '--with-tidy' '--with-xsl' '--with-zlib' '--without-pdo-sqlite' '--without-sqlite3' soap Soap Client => enabled Soap Server => enabled soap.wsdl_cache => 1 => 1 soap.wsdl_cache_dir => /tmp => /tmp soap.wsdl_cache_enabled => 1 => 1 soap.wsdl_cache_limit => 5 => 5 soap.wsdl_cache_ttl => 86400 => 86400 Output from php-fpm phpinfo(): Configuration File (php.ini) Path /usr/local/etc Loaded Configuration File /usr/local/etc/php.ini SOAP Brad Lafountain, Shane Caraveo, Dmitry Stogov Please help, I have tried so many things...

  Read the article

• Dedicated server with a lot of storage and good support - and cost-effective

  - by Martin Burger

  Hello, I am from Germany and looking for a dedicated server located in the US with a lot of storage: 750 - 1500 GB. CPU speed and amount of memory are secondary, the server will host large amounts of media files via http and ftp - the basic task is to help people exchange media files. In Germany, there are some good offers, like "Root Server EQ6" at www.hetzner.de. For example, that company provides support of high quality, and their plans are very cost-effective. The plan mentioned above costs about $90 per month and provides two 1500 GB SATA-II HDDs (Software-RAID 1). In the US, I found (amongst others) Go Daddy and rackspace. Go Daddy offers some "Storage Monster" plans that include 2 x 1,000 GB hard drives for about $180 per month - already twice as much as Hetzner above. However, I found some blog and forum entries that complain about the support provided by Go Daddy. Rackspace seems to provide decent support, but they are very "upscale". Their dedicated servers are customizable and start at $419 - thus, about 4.5 times as much as Hetzner. Can anybody recommend a solution / plan that is comparable to the one by Hetzner? Or are prices for dedicated servers in general much higher than in Germany? Regards, Martin

  Read the article

• Plesk wildcard subdomain not working

  - by avdgaag

  I'm trying to set up a wildcard subdomain on my VPS. Ultimately I want to end up with this: main site: my.domain.tld subdomain: sub1.my.domain.tld - should end up serving my.domain.tld/sub1 I am using plesk 8.6. I have created a DNS A record pointing at my VPS' IP. I have then restarted the DNS server and waited up to 24 hours. But trying ping sub1.my.domain.tld results in an unknown host error. So I know there's more stuff involved, configuring apache etc. But so far, I cannot even get the subdomain working at all, let alone serve up the right content. I have also tried a CNAME record, to no effect. I have also tried creating a regular subdomain with a fixed name, which also does not work. Pre-configured subdomains DO work, like ftp.my.domain.tld or mail.my.domain.tld. I am clearly missing something here, but my hosting provider charges a small fortune for any support request not involving hardware physically burning down, so I'm hesitant to ask them. Any ideas?

  Read the article

• Setting up DNS using VirtualMin/WebMin

  - by Nyxynyx

  I am moving from a cPanel server to one where I've installed VirtualMin. The LAMP stack and the website files have been setup properly and I can access the website by its IP address. Problem: Now its time to point my domain mydomain.com to my new server. After reading many sites describing setting up bind and master zones, I am pretty confused as to what to do, especially coming from a cPanel server where its really simple to set this up. Attempt Tried to register my nameservers ns1.mydomain.com and ns2.mydomain.com at my domain registrar, but I am missing the IPs I need to point these nameservers to. Should I set ns1.mydomain.com to the IP addres of my web server, and not register ns2.mydomain.com? When specifying the DNS for mydomain.com, the first one I've set it to ns1.apadment.com. On the manager/admin page of my webhost provider, I am given the option to create a secondary slave DNS, which I assigned to the IP address of my server. Though I am not sure how the slave DNS will copy the info from my web server? I have assigned this secondary DNS ns.hostprovider.com as the second DNS for mydomain.com I tried creating a Virtual Server under Virtualmin, but it seems to mess up Apache's DocumentRoot for the site by creating and enabling a new vhost file that ends with .conf. I edited the .conf file to point DocumentRoot back to where its supposed to be /var/www/mydomain instead of /user/mydomain.com I believe the next step is to setup the zone. Virtualmin has already created a Master Zone with 8 different addresses (www.mydomain.com, ftp.mydomain.com...). Under Nameservers, there are already 2 records. One is the hostname (random name given by hostprovider, ns12345.ip123-123.net), the other is the secondary slave DNS provided by the host provider. Does having BIND running on my web server makes the server the master DNS? Thank you!

  Read the article

• How to configure SCSI hard drives and RAID for Poweredge 2850 web server

  - by Saul

  I'm trying to set up a Poweredge 2850 as a web server, but as a server novice it's causing me some confusion. Its a virgin install so no data to be lost as yet, so I'd like to get the best arrangement for setting up Windows Server 2008. The box will run IIS, a mail and FTP server. The current physical arrangement of the hot swap drives is 1 73GB 3 146GB 5 blank 0 73GB 2 146GB 4 146GB (but flashes green, amber off) When I enter the PERC config screens on boot up I've got Raid Ch- 0 ID 0 ONLIN A00-00 1 ONLIN A00-01 2 ONLIN A01-00 3 ONLIN A01-01 4 HOTSP I think that drives 0 and 1 are set to RAID 1 and drives 2 and 3 are also set to RAID 1, certainly I can see 2 logical drives, both raid 1 of 69880MB and 139900MB Now what I think I am getting here is that the 2 73GB drives mirror each other and the 2 146GB drives mirror 2? so by my noob thinking if a drive fails I can pull it, insert and new one and it will reduplicate from its matching pair? I think the flashing amber probably indicates a failing drive in slot 4, should that just be binned? What confuses me coming from a home user XP background is that when I load up Windows Server 2008 OS under my computer I only see a C drive of about 70GB capacity. i.e wheres the 146GB drive? Any advice appreciated

  Read the article

• openvpn& iptables -- portforwarding and gateway

  - by Smith.Lai

  The problem is similar to this scenario: iptables rule still take effect after deleted Scenario: There are several clients(C1~C10) providing some services, such as SSH,HTTP..... The clients are actually a personal computer behind NAT. Their IP might be 192.168.0.x For easily access these machines through internet, I built a OpenVPN server(S1). All the C1~C10 connect to S1 with VPN address 10.8.0.x If A user(U1) wanna access C1 SSH through internet, he can connect to S1 with port "55555", and S1 port forward 55555 to 10.8.0.6:22 echo 1 /proc/sys/net/ipv4/ip_forward iptables -t nat -A PREROUTING -i eth0 -p tcp --dport 55555 -j DNAT --to-destination 10.8.0.6:22 It works well until I mark the following in the openvpn server.conf: I marked this because I think this will make all connection go through S1 ;push "redirect-gateway" |-------(NAT)--------| (C1)--| (INTERNET)----(U1) |-----(VPN)----(S1)--| The C1~C10 have their own path to access internet resource through NAT . The server loading would be heavy if all C1~C10 connection go through S1 (for example, C1 is sending data to C2, or C1 is downloading data from a FTP site). Is there a way to solve this quandary?

  Read the article

• BIND9 DNS Problems - Not resolving

  - by clone1018

  I host a BIND9 DNS server for my VirtualMin users to use. And It only resolves for 75% of the people. It has been WELL over 1 week now. Here is a sample. $ttl 38400 @ IN SOA axxim.net. root.axxim.net. ( 1274031391 10800 3600 604800 38400 ) @ IN NS axxim.net. day7tech.com. IN A 96.226.216.37 www.day7tech.com. IN A 96.226.216.37 ftp.day7tech.com. IN A 96.226.216.37 m.day7tech.com. IN A 96.226.216.37 localhost.day7tech.com. IN A 127.0.0.1 webmail.day7tech.com. IN A 96.226.216.37 admin.day7tech.com. IN A 96.226.216.37 mail.day7tech.com. IN A 96.226.216.37 day7tech.com. IN MX 5 mail.day7tech.com.

  Read the article

• Viability of Apache (MPM Worker), FastCGI PHP 4/5.2/5.3, and MySQL 5

  - by Adrian

  My server will be hosting numerous PHP web applications ranging from Joomla, Drupal, and some legacy (read: PHP4) and other custom-built code inherited from clients. This will be a development machine used by a dozen or so web developers and issues like fluctuating loads or particularly high load expectations are not important. Now, my question: are there any concerns I should know about when using Apache w/ MPM Worker, PHP 4/PHP 5.2/PHP 5.3 (all via FastCGI), and MySQL 5 (with a query cache of 64MB)? I have not tested the various applications extensively and I have only recently learned how to install PHP and utilize it via FastCGI (rather than mod_php, which in this case seemed impossible (considering the multiple versions of PHP and the desire to use MPM Worker over MPM Prefork)). I have come to understand that there could be concerns regarding XCache and APC, namely non-thread-safety issues where data becomes corrupted and the capability to use MPM Worker becomes null and void. Is this a valid concern? I have been using my personal testing server (running Ubuntu Server Edition 10.04 in VirtualBox) which has 2GB of RAM available to it. Here is the configuration used (the actual server will likely use a configuration more tailored to suit it's purposes): Apache: Server version: Apache/2.2.14 (Ubuntu) Server built: Apr 13 2010 20:22:19 Server's Module Magic Number: 20051115:23 Server loaded: APR 1.3.8, APR-Util 1.3.9 Compiled using: APR 1.3.8, APR-Util 1.3.9 Architecture: 64-bit Server MPM: Worker threaded: yes (fixed thread count) forked: yes (variable process count) Worker: <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 400 MaxRequestsPerChild 2000 </IfModule> PHP ./configure (PHP 4.4.9, PHP 5.2.13, PHP 5.3.2): --enable-bcmath \ --enable-calendar \ --enable-exif \ --enable-ftp \ --enable-mbstring \ --enable-pcntl \ --enable-soap \ --enable-sockets \ --enable-sqlite-utf8 \ --enable-wddx \ --enable-zip \ --enable-fastcgi \ --with-zlib \ --with-gettext \ Apache php-fastcgi-setup.conf FastCgiServer /var/www/cgi-bin/php-cgi-5.3.2 FastCgiServer /var/www/cgi-bin/php-cgi-5.2.13 FastCgiServer /var/www/cgi-bin/php-cgi-4.4.9 ScriptAlias /cgi-bin-php/ /var/www/cgi-bin/

  Read the article

< Previous Page | 92 93 94 95 96 97 98 99 100 101 102 103  | Next Page >