Search Results

Search found 3567 results on 143 pages for 'instructions'.

Page 96/143 | < Previous Page | 92 93 94 95 96 97 98 99 100 101 102 103  | Next Page >

  • The Windows 8 and Ubuntu 12.04 Dual Boot NIghtmare

    - by Steve
    I have done some research as to how to go about this dual-boot, and I am close, but I need some guidance with booting into Windows 8 (Ubuntu is installed). I have a Lenovo Ideapad y510p. I will go over what I have done to dual-boot this laptop, with windows 8 pre-installed, with Ubuntu 12.04: I followed every instruction to the letter for the 97-vote response here, and everything worked fine up until after the repair boot section: Installing on a Pre-Installed Windows 8 System (UEFI Supported) I ran into the following error upon restarting after the repair boot section: error: invalid arch independent elf magic. This error (a grub issue) disabled me from booting into Ubuntu :( After a little googling, I followed the instructions in the reactivating grub 2 section to resolve the error: http://kb.acronis.com/content/1686 I found a possible solution to fixing the Windows 8 boot issue, and tried it: http://webcache.googleusercontent.com/search?q=cache:i9JMyXzzRpYJ:askubuntu.com/questions/279275/dual-boot-problem-windows-8-ubuntu-12-04+&cd=1&hl=en&ct=clnk&gl=us&client=ubuntu I thought the above solution worked, but when I attempt to boot into Windows 8, I get the following missing file error: File: \Boot\BCD Status: 0xc000000e Info: The Boot Configuration Data for your PC is missing or contains errors. Here is some other information that may be useful: I have 3 partitions devoted to Ubuntu. The first, sda8, has a flag bios_grub (1049 kb). The second, sda9, is where everything else is (96.6 GB). The last, sda10, is for swap (8299 MB). My question is: How do I fix the boot configuration for Windows 8? Any help would be greatly appreciated :) Update 1: When I attempt to boot into UEFI mode, I get the following error: invalid arch independent elf magic (the same error I saw in step 2). Update 2: A useful link here I found: Dual booting Ubuntu 12.04: UEFI and Legacy So, this is my 4th time installing Ubuntu on the laptop, and it looks like I need to install it in UEFI mode. Should I scrap it all again, and reinstall? Or is there ANY way of salvaging my installation? At this point, I can't even boot into Windows (although I have an installation cd to fix the windows boot issue, that would ultimately screw over ubuntu). Update 3: After doing a little more browsing around, I found a cool way around this messy grub stuff, using rEFInd. Rod Smith's post here saved me! Installing ubuntu 12.04.02 in uefi mode Now, I am able to dual-boot Windows 8 and Ubuntu and boot into both operating systems :) I have another issue (relating to the boot configuration in the bios) that I will post as a separate question :)

    Read the article

  • StreamInsight 1.0 Released

    - by Roman Schindlauer
    One piece in the set of products offered in SQL Server 2008 R2 that has generated a lot of buzz and interest during its CTP phase is StreamInsight, Microsoft’s platform for Complex Event Processing. Microsoft’s information platform vision provides enterprises with a “complete approach” to managing information assets, enabling all businesses to gain strategic value from information from the desktop to the datacenter to the cloud. And StreamInsight V1 is one essential piece in this spectrum. After more than a year of blood, sweat, tears, and insane amounts of coffee we are proud to release the first version of our Complex Event Processing Framework.   Those of you who have been following our Community Technology Previews (CTPs) throughout last year have already had the possibility to familiarize themselves with the product. Early feedback was not only incredibly positive, but also very constructive and strongly influenced the final feature set. Four notable increments over our last public CTP are: Count windows Non-occurrence detection (Anti-Join) Dynamic query composition at runtime Synchronize time across input streams Additionally, many smaller issues and bugs were addressed. A few APIs slightly changed with respect to the November CTP, but porting your application to RTM should not require a lot of effort.   Here are the (english) bits - choosing the evaluation license during setup lets you already play with this version. Before you install, make sure to uninstall any previous CTP version:   StreamInsight X86StreamInsight X64   Within a few days, we will update our product page and add download links and instructions there as well.   The StreamInsight documentation is provided through a help file as part of the installation as well as through Books Online on MSDN. We also invite you to visit the StreamInsight Blog and the StreamInsight Forum, which is a great place to discuss questions and issues with the community and the development team.   Regards,Roman Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

    Read the article

  • VirtualBox 4.2.14 is now available

    - by user12611829
    The VirtualBox development team has just released version 4.2.14, and it is now available for download. This is a maintenance release for version 4.2 and contains quite a few fixes. Here is the list from the official Changelog. VMM: another TLB invalidation fix for non-present pages VMM: fixed a performance regression (4.2.8 regression; bug #11674) GUI: fixed a crash on shutdown GUI: prevent stuck keys under certain conditions on Windows hosts (bugs #2613, #6171) VRDP: fixed a rare crash on the guest screen resize VRDP: allow to change VRDP parameters (including enabling/disabling the server) if the VM is paused USB: fixed passing through devices on Mac OS X host to a VM with 2 or more virtual CPUs (bug #7462) USB: fixed hang during isochronous transfer with certain devices (4.1 regression; Windows hosts only; bug #11839) USB: properly handle orphaned URBs (bug #11207) BIOS: fixed function for returning the PCI interrupt routing table (fixes NetWare 6.x guests) BIOS: don't use the ENTER / LEAVE instructions in the BIOS as these don't work in the real mode as set up by certain guests (e.g. Plan 9 and QNX 4) DMI: allow to configure DmiChassisType (bug #11832) Storage: fixed lost writes if iSCSI is used with snapshots and asynchronous I/O (bug #11479) Storage: fixed accessing certain VHDX images created by Windows 8 (bug #11502) Storage: fixed hang when creating a snapshot using Parallels disk images (bug #9617) 3D: seamless + 3D fixes (bug #11723) 3D: version 4.2.12 was not able to read saved states of older versions under certain conditions (bug #11718) Main/Properties: don't create a guest property for non-running VMs if the property does not exist and is about to be removed (bug #11765) Main/Properties: don't forget to make new guest properties persistent after the VM was terminated (bug #11719) Main/Display: don't lose seamless regions during screen resize Main/OVF: don't crash during import if the client forgot to call Appliance::interpret() (bug #10845) Main/OVF: don't create invalid appliances by stripping the file name if the VM name is very long (bug #11814) Main/OVF: don't fail if the appliance contains multiple file references (bug #10689) Main/Metrics: fixed Solaris file descriptor leak Settings: limit depth of snapshot tree to 250 levels, as more will lead to decreased performance and may trigger crashes VBoxManage: fixed setting the parent UUID on diff images using sethdparentuuid Linux hosts: work around for not crashing as a result of automatic NUMA balancing which was introduced in Linux 3.8 (bug #11610) Windows installer: force the installation of the public certificate in background (i.e. completely prevent user interaction) if the --silent command line option is specified Windows Additions: fixed problems with partial install in the unattended case Windows Additions: fixed display glitch with the Start button in seamless mode for some themes Windows Additions: Seamless mode and auto-resize fixes Windows Additions: fixed trying to to retrieve new auto-logon credentials if current ones were not processed yet Windows Additions installer: added the /with_wddm switch to select the experimental WDDM driver by default Linux Additions: fixed setting own timed out and aborted texts in information label of the lightdm greeter Linux Additions: fixed compilation against Linux 3.2.0 Ubuntu kernels (4.2.12 regression as a side effect of the Debian kernel build fix; bug #11709) X11 Additions: reduced the CPU load of VBoxClient in drag'and'drop mode OS/2 Additions: made the mouse wheel work (bug #6793) Guest Additions: fixed problems copying and pasting between two guests on an X11 host (bug #11792) The full changelog can be found here. You can download binaries for Solaris, Linux, Windows and MacOS hosts at http://www.virtualbox.org/wiki/Downloads Technocrati Tags: Oracle Virtualization VirtualBox

    Read the article

  • Announcing Oracle Mobile Timecards for Oracle E-Business Suite, Release 12.1 and Release 12.2

    - by CaroleB
    Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 Oracle E-Business Suite Development is pleased to announce the availability of Oracle Mobile Timecards for Oracle E-Business Suite iPhone application.  With this new mobile app, users can record time on the go, and quickly submit timecards to ensure that downstream processes like Payroll, Projects Costing and Vendor Settlements are executed on time. Key features include: Enter time day-wise for easy time booking Enter time in Quick Time or Regular Time modes Support Payroll and Projects based time entry Aggregate day-wise entries into timecard periods Submit and view timecards while on the go Oracle Mobile Timecards for Oracle E-Business Suite is currently available on OS, and Android availability is planned. It is available to Oracle E-Business Suite customers as part of an existing Oracle Time and Labor product license; no new "mobile" license is required. Download Availability You can download Oracle E-Business Suite Smartphone Applications directly from the Apple Store and run them on Oracle Business Suite 12.1.3 or 12.2.3 – the same client-side code runs with either release: iTunes link: https://itunes.apple.com/us/app/oracle-timecards-for-oracle/id883064245?mt=8  For each app, an administrator performs a simple, one-time ennoblement using server-side patches. For deployment instructions, see Oracle E-Business Suite Mobile Apps, Release 12.1 and 12.2 Documentation (Note 1641772.1). Demo Availability   Support for demo-ING in GS environments will be available shortly. A demo preview of Oracle Mobile Timecards for Oracle E-Business Suite is available here. Configured Layouts on Mobile Timecards Note.1671889.1 Mobile Timecard Layout Configuration Whitepaper for OTL Mobile Time Entry /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-family:"Times New Roman","serif";}

    Read the article

  • Use CSS Selectors with HtmlUnit

    - by kerry
    HtmlUnit is a great library for performing web integration tests in Java.  But sometimes node traversal can be somewhat cumbersome. Fear not fellow automated tester (good for you!).  I found a great little project on Github that will allow you to query your document for elements via css selectors similar to jQuery. The project is located at https://github.com/chrsan/css-selectors.  You can use Maven to build it, or download 1.0.2 here.  Beware.  I will not be updating this link so I suggest you download the latest code. In any case, you can use it like so: // from HtmlUnit getting started final WebClient webClient = new WebClient(); final HtmlPage page = webClient.getPage("http://htmlunit.sourceforge.net"); final DOMNodeSelector cssSelector = new DOMNodeSelector(page.getDocumentElement()); final Set elements = cssSelector.querySelectorAll("div.section h2"); final Node first = elements.iterator().next(); assertThat(first.getTextContent(), equalTo("HtmlUnit")); The only problem here is that the querySelectAll returns a Set<Node>.  Not HtmlElement like we may want in some cases.   However, if you were to reflect on the Set, you would find that it is indeed a Set of HtmlElement objects. Typically, I like to create a base class for my web tests.  Just for fun, I am using the $ method similar to jQuery. public class WebTestBase { protected WebClient webClient; protected HtmlPage htmlPage; protected void goTo(final String url){ return (HtmlPage)webClient.getPage(url); } protected List $(final String cssSelector) { final DOMNodeSelector cssSelector = new DOMNodeSelector(htmlPage.getDocumentElement()); final Set nodes = cssSelector.querySelectorAll("div.section h2"); // for some reason Set cannot be cast to Set? final List elements = new ArrayList(nodes.size()); for (final Node node : nodes) { elements.add((HtmlElement)node); } return elements; } } Now we can write tests like this: public class LoginWebTest extends WebTestBase { @Test public void login_page_has_instructions() throws Exception { goTo(baseUrl + "/login") assertThat( $("p.instructions").size(), equalTo(1) ); } }

    Read the article

  • VirtualBox image SOA Suite &amp; BPM Suite 11.1.1.6.0 & Your feedback?

    - by JuergenKress
    The integration PM team is very pleased to announce the release of a new version of our pre-configured SOA/BPM VirtualBox image for testing and evaluation. This VirtualBox appliance contains a fully configured, ready-to-use SOA/BPM/Webcenter 11.1.1.6.0 installation. All you need is to install Oracle VM VirtualBox on your desktop/laptop and import the SOA/BPM appliance and you are ready to try out SOA Suite and BPM Suite -- no installation and configuration required! The following software is installed in this VritualBox image: Oracle Enterprise Linux (64-bit) EL 5 Update 5 Oracle XE Database 11.2.0 Oracle SOA Suite 11.1.1.6.0 (includes Service Bus) Oracle BPM Suite 11.1.1.6.0 Oracle Webcenter Content (Enterprise Content Management) 11.1.1.6.0 Oracle Webcenter Suite 11.1.1.6.0 Oracle JDeveloper 11.1.1.6.0 JRockit R28.2.0-79-146777-1.6.0_29s Sun Java SDK 1.6.0_29-b11 If you want to try it out, please go to the Pre-built Virtual Machine for SOA Suite and BPM Suite 11g OTN page for detailed instructions on downloading and importing the VirtualBox image. Jon Petter Hjulstad published the first impression at his blog Twitter & LinkedIn We have been waiting for the new VirtualBox Image for a long time, and finally it is here. The appliance has improved in many ways since last release, so it has been worth waiting for. Both the appliance itself and the documentation is excellent. It is evident that Oracle has listened to feedback on the previous release, and I think the developer VMs are useful. Especially the adoption of new patchsets and versions (ex when 12c will be available) will gain a lot from quick getting hands-on experiences. This VirtualBox appliance is a multipurpose image which can be used in different domain configurations. The image has a number of pre-configured domains that you can use depending on your need. The image can be set up so that it requires use of as few resources as possible, you can for instance easily disable B2B if you do not need it, or you can shut down the desktop console and save 600MB. It is important to say that this image is not for production purposes. Read the full article SOA & BPM Partner Community For regular information on Oracle SOA Suite become a member in the SOA & BPM Partner Community for registration please visit  www.oracle.com/goto/emea/soa (OPN account required) If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix ForumTechnorati Tags: SOA Suite Image,VirtualBox,BPM suite Image,SOA Specialization award,SOA Community,Oracle SOA,Oracle BPM,BPM Community,OPN,Jürgen Kress

    Read the article

  • New Feature in ODI 11.1.1.6: Enterprise Data Quality Integration

    - by Julien Testut
    Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Oracle Data Integrator 11.1.1.6.0 introduces a new Open Tool called EnterpriseDataQuality which allows ODI users to invoke an Oracle Enterprise Data Quality Job from a Package. This post will give you an overview of this new feature. Oracle Enterprise Data Quality (OEDQ) provides organizations with an integrated suite of data quality tools that offer an end-to-end solution to measure, improve, and manage the quality of data from any domain, including customer and product data. The addition of the EnterpriseDataQuality Open Tool extends the inline Data Quality capabilities of Oracle Data Integrator with Oracle Enterprise Data Quality powerful data profiling, cleansing, matching, and monitoring capabilities. The EnterpriseDataQuality Open Tool can invoke any OEDQ Job stored in a Project. This Open Tool connects to an OEDQ server using a JMX (Java Management Extensions) interface. Once installed, this Open Tool will be found under Plugins in the Package Toolbox area: This EnterpriseDataQuality Open Tool takes a couple of parameters as inputs such as the Enterprise Data Quality Job and Project names, the OEDQ hostname and JMX port etc. With the EnterpriseDataQuality Open Tool, ODI customers can now incorporate their Oracle Enterprise Data Quality processes within their Data Integration workflows. You will find instructions about how to use the Enterprise Data Quality Open Tool in the Oracle Data Integrator documentation at: Using the EnterpriseDataQuality Open Tool.You can find an overview of all the new features introduced in ODI 11.1.1.6 in the following document: ODI 11.1.1.6 New Features Overview.

    Read the article

  • New channels for Exadata 11.2.3.1.1

    - by Rene Kundersma
    With the release of Exadata 11.2.3.1.0 back in April 2012 Oracle has deprecated the minimal pack for the Exadata Database Servers (compute nodes). From that release the Linux Database Server updates will be done using ULN and YUM. For the 11.2.3.1.0 release the ULN exadata_dbserver_11.2.3.1.0_x86_64_base channel was made available and Exadata operators could subscribe their system to it via linux.oracle.com. With the new 11.2.3.1.1 release two additional channels are added: a 'latest' channel (exadata_dbserver_11.2_x86_64_latest) a 'patch' channel (exadata_dbserver_11.2_x86_64_patch) The patch channel has the new or updated packages updated in 11.2.3.1.1 from the base channel. The latest channel has all the packages from 11.2.3.1.0 base and patch channels combined.  From here there are three possible situations a Database Server can be in before it can be updated to 11.2.3.1.1: Database Server is on Exadata release < 11.2.3.1.0 Database Server is patched to 11.2.3.1.0 Database Server is freshly imaged to 11.2.3.1.0 In order to bring a Database Server to 11.2.3.1.1 for all three cases the same approach for updating can be used (using YUM), but there are some minor differences: For Database Servers on a release < 11.2.3.1.0 the following high-level steps need to be performed: Subscribe to el5_x86_64_addons, ol5_x86_64_latest and  exadata_dbserver_11.2_x86_64_latest Create local repository Point Database Server to the local repository* install the update * during this process a one-time action needs to be done (details in the README) For Database Servers patched to 11.2.3.1.0: Subscribe to patch channel  exadata_dbserver_11.2_x86_64_patch Create local repository Point Database Server to the local repository Update the system For Database Servers freshly imaged to 11.2.3.1.0: Subscribe to patch channel  exadata_dbserver_11.2_x86_64_patch Create local  repository Point Database Server to the local repository Update the system The difference between 'situation 2' (Database Server is patched to 11.2.3.1.0) and 'situation 3' (Database Server is freshly imaged to 11.2.3.1.0) is that in situation 2 the existing Exadata-computenode.repo file needs to be edited while in situation 3 this file is not existing  and needs to be created or copied. Another difference is that you will end up with more OFA packages installed in situation 2. This is because none are removed during the updating process.  The YUM update functionality with the new channels is a great enhancements to the Database Server update procedure. As usual, the updates can be done in a rolling fashion so no database service downtime is required.  For detailed and up-to-date instructions always see the patch README's 1466459.1 patch 13998727 888828.1 Rene Kundersma

    Read the article

  • Wordpress Installation (on IIS and SQL Server)

    - by Davide Mauri
    To proceed with the installation of Wordpress on SQL Server and IIS, first of all, you need to do the following steps Create a database on SQL Server that will be used by Wordpress Create login that can access to the just created database and put the user into ddladmin, db_datareader, db_datawriter roles Download and unpack Wordpress 3.3.2 (latest version as of 27 May 2012) zip file into a directory of your choice Download the wp-db-abstraction 1.1.4 (latest version as of 27 May 2012) plugin from wordpress.org website Now that the basic action has been done, you can start to setup and configure your Wordpress installation. Unpack and follow the instructions in the README.TXT file to install the Database Abstraction Layer. Mainly you have to: Upload wp-db-abstraction.php and the wp-db-abstraction directory to wp-content/mu-plugins.  This should be parallel to your regular plugins directory.  If the mu-plugins directory does not exist, you must create it. Put the db.php file from inside the wp-db-abstraction.php directory to wp-content/db.php Now you can create an application pool in IIS like the following one Create a website, using the above Application Pool, that points to the folder where you unpacked Wordpress files. Be sure to give the “Write” permission to the IIS account, as pointed out in this (old, but still quite valid) installation manual: http://wordpress.visitmix.com/development/installing-wordpress-on-sql-server#iis Now you’re ready to go. Point your browser to the configured website and the Wordpress installation screen will be there for you. When you’re requested to enter information to connect to MySQL database, simply skip that page, leaving the default values. If you have installed the Database Abstraction Layer, another database installation screen will appear after the one used by MySQL, and here you can enter the configuration information needed to connect to SQL Server. After having finished the installation steps, you should be able to access and navigate your wordpress site.  A final touch, and it’s done: just add the needed rewrite rules http://wordpress.visitmix.com/development/installing-wordpress-on-sql-server#urlrewrite and that’s it! Well. Not really. Unfortunately the current (as of 27 May 2012) version of the Database Abstraction Layer (1.1.4) has some bugs. Luckily they can be quickly fixed: Backslash Fix http://wordpress.org/support/topic/plugin-wp-db-abstraction-fix-problems-with-backslash-usage Select Top 0 Fix Make the change to the file “.\wp-content\mu-plugins\wp-db-abstraction\translations\sqlsrv\translations.php” suggested by “debettap”   http://sourceforge.net/tracker/?func=detail&aid=3485384&group_id=315685&atid=1328061 And now you have a 100% working Wordpress installation on SQL Server! Since I also wanted to take advantage of SQL Server Full Text Search, I’ve created a very simple wordpress plugin to setup full-text search and to use it as website search engine: http://wpfts.codeplex.com/ Enjoy!

    Read the article

  • Subterranean IL: Volatile

    - by Simon Cooper
    This time, we'll be having a look at the volatile. prefix instruction, and one of the differences between volatile in IL and C#. The volatile. prefix volatile is a tricky one, as there's varying levels of documentation on it. From what I can see, it has two effects: It prevents caching of the load or store value; rather than reading or writing to a cached version of the memory location (say, the processor register or cache), it forces the value to be loaded or stored at the 'actual' memory location, so it is then immediately visible to other threads. It forces a memory barrier at the prefixed instruction. This ensures instructions don't get re-ordered around the volatile instruction. This is slightly more complicated than it first seems, and only seems to matter on certain architectures. For more details, Joe Duffy has a blog post going into the details. For this post, I'll be concentrating on the first aspect of volatile. Caching field accesses To demonstrate this, I created a simple multithreaded IL program. It boils down to the following code: .class public Holder { .field public static class Holder holder .field public bool stop .method public static specialname void .cctor() { newobj instance void Holder::.ctor() stsfld class Holder Holder::holder ret }}.method private static void Main() { .entrypoint // Thread t = new Thread(new ThreadStart(DoWork)) // t.Start() // Thread.Sleep(2000) // Console.WriteLine("Stopping thread...") ldsfld class Holder Holder::holder ldc.i4.1 stfld bool Holder::stop call instance void [mscorlib]System.Threading.Thread::Join() ret}.method private static void DoWork() { ldsfld class Holder Holder::holder // while (!Holder.holder.stop) {} DoWork: dup ldfld bool Holder::stop brfalse DoWork pop ret} If you compile and run this code, you'll find that the call to Thread.Join() never returns - the DoWork spinlock is reading a cached version of Holder.stop, which is never being updated with the new value set by the Main method. Adding volatile to the ldfld fixes this: dupvolatile.ldfld bool Holder::stopbrfalse DoWork The volatile ldfld forces the field access to read direct from heap memory, which is then updated by the main thread, rather than using a cached copy. volatile in C# This highlights one of the differences between IL and C#. In IL, volatile only applies to the prefixed instruction, whereas in C#, volatile is specified on a field to indicate that all accesses to that field should be volatile (interestingly, there's no mention of the 'no caching' aspect of volatile in the C# spec; it only focuses on the memory barrier aspect). Furthermore, this information needs to be stored within the assembly somehow, as such a field might be accessed directly from outside the assembly, but there's no concept of a 'volatile field' in IL! How this information is stored with the field will be the subject of my next post.

    Read the article

  • Using Movemail with Thunderbird on Ubuntu

    - by rxt
    I'm trying to read local mail with Thunderbird on Ubuntu (with both 12.04 and 13.04). I've followed the instructions found here: How can I access system mail in /var/mail/ via thunderbird? I can read mail on the system using alpine or vim, so I know the mailbox is not empty. When I click the get-mail button, nothing happens. I see no Inbox (or any folder structure) for the specific account. I've set the rights for /var/mail to 1777. Settings server name: localhost username: john How can I get this working? Okay, considering the extra bounty, I would like to get this working like normal mail. The accepted answer from Qasim resulted in a much more usable situation than before - opening mail in Thunderbird with layout. I still face three problems though. When new mail is received in the mailbox, Thunderbird won't see this until after I restart Thunderbird. When Thunderbird is restarted, all mail is reset to unread and deleted mail is undone. This is probably because Thunderbird reads the mail from the /var/mail/www-data file, but doesn't update this file. So after restarting, it simply reads this file again, with the new mail and all old mail. This is probably a postfix issue: mail is sent out to existing mail addresses, but cannot be delivered because the receiving mailserver cannot be reached. This results in "Undelivered mail returned to sender". Only one mailserver can be reached: localhost. Because this is a test system, I don't want real customers to receive mail. I've blocked mail ports in UFW to be sure. When opening the returned mail, I can scroll down and then I see the original mail with proper layout. So I can read the mail, see if the proper images are included, and for me that's workable. Having to restart TB to read new mail - I know when new mail arrives, so I know when to restart. Having old mail restored after a restart - not big problem as well. I can delete the mail file if it gets too much. I know how it works, but it would be nice if it worked like normal.

    Read the article

  • How do you exclude yourself from Google Analytics on your website using cookies?

    - by Cold Hawaiian
    I'm trying to set up an exclusion filter with a browser cookie, so that my own visits to my don't show up in my Google Analytics. I tried 3 different methods and none of them have worked so far. I would like help understanding what I am doing wrong and how I can fix this. Method 1 First, I tried following Google's instructions, http://www.google.com/support/analytics/bin/answer.py?hl=en&answer=55481, for excluding traffic by Cookie Content: Create a new page on your domain, containing the following code: <body onLoad="javascript:pageTracker._setVar('test_value');"> Method 2 Next, when that didn't work, I googled around and found this Google thread, http://www.google.com/support/forum/p/Google%20Analytics/thread?tid=4741f1499823fcd5&hl=en, where the most popular answer says to use a slightly different code: SHS Analytics wrote: <body onLoad="javascript:_gaq.push(['_setVar','test_value']);"> Thank you! This has now set a __utmv cookie containing "test_value", whereas the original: pageTracker._setVar('test_value') (which Google is still recommending) did not manage to do that for me (in Mac Safari 5 and Firefox 3.6.8). So I tried this code, but it didn't work for me. Method 3 Finally, I searched StackOverflow and came across this thread, http://stackoverflow.com/questions/3495270/exclude-my-traffic-from-google-analytics-using-cookie-with-subdomain, which suggests that the following code might work: <script type="text/javascript"> var _gaq = _gaq || []; _gaq.push(['_setVar', 'exclude_me']); _gaq.push(['_setAccount', 'UA-xxxxxxxx-x']); _gaq.push(['_trackPageview']); // etc... </script> This script appeared in the head element in the example, instead of in the onload event of the body like in the previous 2 examples. So I tried this too, but still had no luck with trying to exclude myself from Google Analytics. Re-iterate question So, I tried all 3 methods above with no success. Am I doing something wrong? How can I exclude myself from my Google Analytics using an exclusion cookie for my browser? Update I've been testing this for several days now, and I've confirmed that the 2nd method of excluding yourself from tracking does indeed work. The problem was that the filter settings weren't properly applied to my profile, which has been corrected. See the accepted answer below.

    Read the article

  • HighPoint RocketRAID 62x Controller

    - by TeXnewbie
    I have the subject card recently installed in Ubuntu 12.04.1 LTS (GNU/Linux 3.2.0-31-generic x86_64). See partial lspci -vv listing below (complete listing played havoc with pre tags): 03:00.0 RAID bus controller: HighPoint Technologies, Inc. Device 0622 (rev 01) Subsystem: HighPoint Technologies, Inc. Device 0001 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 9c00 [size=8] Region 1: I/O ports at 9800 [size=4] Region 2: I/O ports at 9400 [size=8] Region 3: I/O ports at 9000 [size=4] Region 4: I/O ports at 8c00 [size=16] Region 5: Memory at fdbff000 (32-bit, non-prefetchable) [size=2K] Expansion ROM at fdbe0000 [disabled] [size=64K] Capabilities: I followed instructions I found at https://help.ubuntu.com/community/RocketRaid to compile the drivers for it, and although performing the process described there seemed to work fine with no noticeable errors, when I rebooted after performing that procedure I could not boot. During dkms steps, I noticed messages indicating that (If next boot fails, revert to initrd.img-3.2.0-31-generic.old-dkms image) update-initramfs................ so I booted using a Ubuntu 12.10 LiveDVD and reverted to the old-dkms initrd.img as suggested above, but this failed to repair the boot problem. Ultimately, I used https://help.ubuntu.com/community/Boot-Repair in Ubuntu-Secure-Remix to fix the boot problem and was able to boot normally again, but now with the newly generated initrd.img in place again (which now boots normally), when I modprobe the rr62x kernel module, I immediately get a hard crash with messages to console about a kernel paging request that seems to have caused the problem. I've tried on multiple occasions now to use the newly built kernel module so as to allow me to use an eSATA port multiplier plugged into the card, but to no avail. Any suggestions on fixes or workarounds (I've read that some of the HighPoint cards (2720SGL) seem to work as a host bus adapter and thus may not need a custom driver, but that seems not to be the case for mine) would be most appreciated. My goal is to use the card as described here and with software RAID mdadm utilities. If necessary, I can hand-copy the console messages after the hard crash into a follow-up message, but I obviously can't do a cut/paste. I'll gladly provide any other details that are needed, but not sure what those would be at this point, so I'll refrain from adding other details for now. Thanks in advance for any help.

    Read the article

  • Are there deprecated practices for multithread and multiprocessor programming that I should no longer use?

    - by DeveloperDon
    In the early days of FORTRAN and BASIC, essentially all programs were written with GOTO statements. The result was spaghetti code and the solution was structured programming. Similarly, pointers can have difficult to control characteristics in our programs. C++ started with plenty of pointers, but use of references are recommended. Libraries like STL can reduce some of our dependency. There are also idioms to create smart pointers that have better characteristics, and some version of C++ permit references and managed code. Programming practices like inheritance and polymorphism use a lot of pointers behind the scenes (just as for, while, do structured programming generates code filled with branch instructions). Languages like Java eliminate pointers and use garbage collection to manage dynamically allocated data instead of depending on programmers to match all their new and delete statements. In my reading, I have seen examples of multi-process and multi-thread programming that don't seem to use semaphores. Do they use the same thing with different names or do they have new ways of structuring protection of resources from concurrent use? For example, a specific example of a system for multithread programming with multicore processors is OpenMP. It represents a critical region as follows, without the use of semaphores, which seem not to be included in the environment. th_id = omp_get_thread_num(); #pragma omp critical { cout << "Hello World from thread " << th_id << '\n'; } This example is an excerpt from: http://en.wikipedia.org/wiki/OpenMP Alternatively, similar protection of threads from each other using semaphores with functions wait() and signal() might look like this: wait(sem); th_id = get_thread_num(); cout << "Hello World from thread " << th_id << '\n'; signal(sem); In this example, things are pretty simple, and just a simple review is enough to show the wait() and signal() calls are matched and even with a lot of concurrency, thread safety is provided. But other algorithms are more complicated and use multiple semaphores (both binary and counting) spread across multiple functions with complex conditions that can be called by many threads. The consequences of creating deadlock or failing to make things thread safe can be hard to manage. Do these systems like OpenMP eliminate the problems with semaphores? Do they move the problem somewhere else? How do I transform my favorite semaphore using algorithm to not use semaphores anymore?

    Read the article

  • Ubuntu Dual Screen Using Virtual Machine - AMD GPU

    - by Chris
    I've been searching online and reading tutorials and etc about how to make my ubuntu VM dual screen(x86_64). I have first tried to run these commands: sudo aticonfig --initial -f which gave me the ouput of: sudo: aitconfig: command not found I then googled the output and followed these instructions that I tells me to install my ATI drivers onto my ubuntu. wget http://www2.ati.com/drivers/linux/ati-driver-installer-11-5-x86.x86_64.run sudo sh ati-driver-installer-11-5-x86.x86_64.run --buildpkg Ubuntu/natty sudo dpkg -i *.deb sudo apt-get -f install sudo aticonfig -f --initial --adapter=all sudo reboot It all works well until I input sudo apt-get -f install which gives me the following output: sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done 0 upgraded, 0 newly installed, 0 to remove and 25 not upgraded. 3 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up fglrx (2:8.850-0ubuntu1) ... update-alternatives: error: alternative link /usr/bin/aticonfig is already managed by x86_64-linux-gnu_gl_conf. dpkg: error processing fglrx (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of fglrx-amdcccle: fglrx-amdcccle depends on fglrx; however: Package fglrx is not configured yet. dpkg: error processing fglrx-amdcccle (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of fglrx-dev: fglrx-dev depends on fglrx; however: Package fglrx is not configured yet. dpkg: error processing fglrx-dev (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: fglrx fglrx-amdcccle fglrx-dev E: Sub-process /usr/bin/dpkg returned an error code (1) At this point, I don't know what to do since running: gksudo amdcccle For the record, I have 3D acceleration turned on. The following is my GPU for my VM lspci | grep VGA 00:02.0 VGA compatible controller: InnoTek Systemberatung GmbH VirtualBox Graphics Adapter Any Help on how I can make my VM dual screen with Ubuntu would be great. Thank you in advance.

    Read the article

  • OBIEE version 11.1.1.7.131017 has been released

    - by inowodwo
    The Business Intelligence Enterprise Edition 11.1.1.7.131017 patch set has been released, and is available to download from My Oracle Support (https:\\support.oracle.com). Per the patch readme: This patch set is available for all customers who are using Oracle Business Intelligence Enterprise Edition 11.1.1.7.0 and 11.1.1.7.1. It is also available for Exalytics customers who have applied the Exalytics PS3 patch. Patch 17530796 - OBIEE BUNDLE PATCH 11.1.1.7.131017 (Patch) is comprised of the following patches, which are not available separately:     Patch 16913445 - Patch 11.1.1.7.131017 (1 of 8) Oracle Business Intelligence Installer (BIINST)     Patch 17463314 - Patch 11.1.1.7.131017 (2 of 8) Oracle Business Intelligence Publisher (BIP)     Patch 17300417 - Patch 11.1.1.7.131017 (3 of 8) Enterprise Performance Management Components Installed from BI Installer 11.1.1.7.0 (BIFNDNEPM))     Patch 17463395 - Patch 11.1.1.7.131017 (4 of 8) Oracle Business Intelligence Server (BIS)     Patch 17463376 - Patch 11.1.1.7.131017 (5 of 8) Oracle Business Intelligence Presentation Services (BIPS)     Patch 17300045 - Patch 11.1.1.7.131017 (6 of 8) Oracle Business Intelligence Presentation Services (BIPS)     Patch 16997936 - Patch 11.1.1.7.131017 (7 of 8) Oracle Business Intelligence Presentation Services (BIPS)     Patch 17463403 - Patch 11.1.1.7.131017 (8 of 8) Oracle Business Intelligence Platform Client Installers and MapViewer Also you must download: Patch 16569379 - Dynamic Monitoring Service patch The instructions to apply the bundle patch are given in the patch readme along with some important notes if you are upgrading from 11.1.1.6.x versions. The new functionality in this patch includes:     Support for Microsoft Internet Explorer 10     Support for Oracle BI Mobile App Designer     Support for improved exporting functionality into Microsoft Excel For more information please refer to document: OBIEE 11g 11.1.1.7.131017 is Available for Oracle Business Intelligence Enterprise Edition and Exalytics (Doc ID 1595219.1) In addition we strongly recommend you review this document: OBIEE Suite Bundle Patches (Doc ID 1591422.1), which explains the new naming convention, the strategy behind bundle patches and other interesting facts about OBIEE patching. Please take some time to review it.

    Read the article

  • Cannot get Virtualbox to install properly on Ubuntu 12.04

    - by lopac1029
    I cannot get Virtualbox to install properly on my 12.04. I first went with a manual install for the .deb from the old builds section of the Virtualbox page. That .deb opened up the Software Center and installed. Then I got the error coming up of VT-x/AMD-V hardware acceleration is not available on your system. Your 64-bit guest will fail to detect a 64-bit CPU and will not be able to boot. which I can only assume was due to my Ubuntu version being 32-bit (System Details - Overview - OC type: 32-bit, right?) So I followed these instructions to remove the .deb manually, restarted my laptop, and then FOUND the actual Virtualbox install in the Software Center and installed from that (assuming it would give me the correct version I need for my system) So after all that (and then some), I'm still getting the same error when I connect to my new job's project in Virtualbox. Can anyone point me in the right direction of what to do here? This is the first time I've ever worked with Virtualbox, and no one at this company is using Ubuntu, so I'm on my own here. EDIT: Here is the direct info from running the 2 suggested commands Inspiron-1750-brick:~ $lscpu Architecture: i686 CPU op-mode(s): 32-bit, 64-bit Byte Order: Little Endian CPU(s): 2 On-line CPU(s) list: 0,1 Thread(s) per core: 1 Core(s) per socket: 2 Socket(s): 1 Vendor ID: GenuineIntel CPU family: 6 Model: 23 Stepping: 10 CPU MHz: 2100.000 BogoMIPS: 4189.45 L1d cache: 32K L1i cache: 32K L2 cache: 2048K Inspiron-1750-brick:~ $cat /proc/cpuinfo processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T6500 @ 2.10GHz stepping : 10 microcode : 0xa07 cpu MHz : 1200.000 cache size : 2048 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts aperfmperf pni dtes64 monitor ds_cpl est tm2 ssse3 cx16 xtpr pdcm sse4_1 xsave lahf_lm dtherm bogomips : 4189.80 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 23 model name : Intel(R) Core(TM)2 Duo CPU T6500 @ 2.10GHz stepping : 10 microcode : 0xa07 cpu MHz : 1200.000 cache size : 2048 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 13 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts aperfmperf pni dtes64 monitor ds_cpl est tm2 ssse3 cx16 xtpr pdcm sse4_1 xsave lahf_lm dtherm bogomips : 4189.45 clflush size : 64 cache_alignment : 64 address sizes : 36 bits physical, 48 bits virtual power management:

    Read the article

  • How do I configure sound with PulseAudio and Multiseat?

    - by Anthony
    In the spirit of full disclosure, i just posted this question to the ubuntu forums, but i figure more heads working on it couldn't hurt. I have a multi-seat setup working quite well. Hot plugging input devices works as expected and such. The only issue I am still not able to resolve is getting the audio for each seat. Here is a summary of my attempts at getting audio to work: Make ~/.pulse/default.pa dynamically configured based on which $DISPLAY the user logs in at. See this pastebin for the details. Load pulseaudio as a system-wide instance. Couldn't get this to work. None of the audio hardware was accessible to the users. Use udev rules to mark seats in ConsoleKit. Following udev guidelines found here: http://www.freedesktop.org/wiki/Software/systemd/multiseat I didn't think this would work, although it was "guaranteed" to work by someone in irc.freenode #pulseaudio None of those attempts yielded success, which is why I now turn to the community for help. It is quite possible that the suggested methods work and I just messed some aspect of it up, idk. This is the last piece of the puzzle which is needed before I can go and update the MultiseatX page to include instructions for Ubuntu 12.04. My understandings on the situation: Access to pulseaudio is restricted to the active session as marked by ConsoleKit (something about an ACL). CK can only mark one session as active at a time. This simple little fact of life leads me to believe that the solution should involve pulseaudio being run as a system-wide instance. Each user should connect to the pulse server and be limited to a subset of all the hardware. Maybe each user connects to the pulse server via localhost, idk. I do know that regardless of my attempts and their failed results, I was always able to use sudo aplay -D plughw:0,0 /usr/share/sounds/alsa/Front_Center.wav to play something to any of the hardware. I'm grasping at straws and am now down to the last few hairs i can pull out of my head. Please, help me figure this out so we can share the wealth. Any additional information needed will be provided at your request.

    Read the article

  • Failed 12.04 installation

    - by Rob Sayer
    I tried installing Ubuntu 12.04 today. Not an upgrade, a new installation. It didn't work. My computer specs: Computer: Compaq presario CQ-104CA OS: Windows 7 Home 64 bit CPU: AMD V140 BIOS: latest Graphics: amd m880g with ati mobility radeon hd 4250 Wireless: atheros ar9285 Internal HD:SATA I wasn't connected to the internet at the time ... I know of a number of people who have installed ubuntu unconnected and just updated later. It seemed to go normally until I got to the part where I chose to install dual boot linux/windows. Then, the screen went black and the following test appeared (I left out the [OK]'s): checking battery state starting crash report submission daemon stating cpu interrupts balancing daemon stopping system V runlevel compatibility starting configure network device security stopping configure network device security stopping cold plug devices stopping log initial device creation starting enable remaining boot-time encrypting devices starting configure network device security starting save udev log and update rules stopping save udev log and update rules stopping enable remaining boot-time encrypted block devices checking for running unattended-upgrades acpid: exiting speech-dispatcher disabled: edit /etc/default/speech-disorder At this point, the CD is ejected. Then nothing. If I press the return key, it boots Windows. I don't think that's what's supposed to happen. Thinking the cd media or dvd drive may have been faulty, I downloaded the .iso again and made a bootable USB stick, as per your instructions. This time there was no cryptic crash screen. It just booted windows. I can't find any log files it may have left. Thinking the amd64 version may have been the wrong one, I tried downloading the x86 version. Same thing, both from cd and usb drive. Note I downloaded both files twice. I doubt it was a corrupted d/l. This is supposed to be a simple, transparent install. I went to the time and trouble of looking up my devices and drivers re ubuntu beforehand, and was prepared to do some configuration, though I know someone who has the same wireless device and his worked righted out of the box. But I spent over 3 hours trying to install it with only the above to show for it.

    Read the article

  • How do I make the launcher progress bar work with my application?

    - by Kevin Gurney
    Background Research I am attempting to update the progress bar within the Unity launcher for a simple python/Gtk application created using Quickly called test; however, following the instructions in this video, I have not been able to successfully update the progress bar in the Unity launcher. In the Unity Integration video, Quickly was not used, so the way that the application was structured was slightly different, and the code used in the video does not seem to function properly without modification in a default Quickly ubuntu-application template application. Screenshots Here is a screenshot of the application icon as it is currently displayed in the Unity Launcher. Here is a screenshot of the kind of Unity launcher progress bar functionality that I would like (overlayed on mail icon: wiki.ubuntu.com). Code class TestWindow(Window): __gtype_name__ = "TestWindow" def finish_initializing(self, builder): # pylint: disable=E1002 """Set up the main window""" super(TestWindow, self).finish_initializing(builder) self.AboutDialog = AboutTestDialog self.PreferencesDialog = PreferencesTestDialog # Code for other initialization actions should be added here. self.add_launcher_integration() def add_launcher_integration(self): self.launcher = Unity.LauncherEntry.get_for_desktop_id("test.destkop") self.launcher.set_property("progress", 0.75) self.launcher.set_property("progress_visible", True) Expected Behavior I would expect the above code to show a progress bar that is 75% full overlayed on the icon for the test application in the Unity Launcher, but the application only runs and displays no progress bar when the command quickly run is executed. Problem Investigation I believe that the problem is that I am not properly getting a reference to the application's main window, however, I am not sure how to properly fix this problem. I also believe that the line: self.launcher = Unity.LauncherEntry.get_for_desktop_id("test.destkop") may be another source of complication because Quickly creates .desktop.in files rather than ordinary .desktop files, so I am not sure if that might be causing issues as well. Perhaps, another source of the issue is that I do not entirely understand the difference between .desktop and .desktop.in files. Does it possibly make sense to make a copy of the test.desktop.in file and rename it test.desktop, and place it in /usr/share/applications in order for get_for_desktop_id("test,desktop") to reference the correct .desktop file? Related Research Links Although, I am still not clear on the difference between .desktop and .desktop.in files, I have done some research on .desktop files and I have come across a couple of links: Desktop Entry Files (library.gnome.org) Desktop File Installation Directory (askubuntu.com) Unity Launcher API (wiki.ubuntu.com) Desktop Files: putting your application in the desktop menus (developer.gnome.org) Desktop Menu Specification (standards.freedesktop.org)

    Read the article

  • How to integrate Java ME SDK 3.2 with NetBeans

    - by SungmoonCho
    Many people like to use Java ME SDK with IDEs. We provided instructions on how to integrate the SDK with NetBeans through the download page, and also through the release note, however, let me explain it here once again with some screen shots. 1. Download Java ME SDK and NetBeans plugin from here. 2. Install Java ME SDK first. You will have the emulator and the runtime on your machine. Also please unarchive the NetBeans plugin somewhere. 3. Launch NetBeans. 4. Go to "Tools" - "Plugins". 5. Check out the "Installed" tab. Check "Show details". If you see the previous version of Java ME SDK Tools installed already. Check those to uninstall them. 6. Go to "Settings" tab. 7. Click "Add", and provide the location of NetBeans plugin. In my case, it is "file:/C:/Users/sungcho/Downloads/nb-me-sdk-plugins-uc/updates.xml". Don't forget to add "updates.xml" at the end. 8. Click "Okay" 9. Click "Available Plugins" tab. 10. If you scroll down, you will see three Java ME SDK Tools. Check "Java ME SDK Tools" plugin. Also check others as you desire. 11. Follow the instruction and install them. 12. Restart NetBeans 13. That is it. Done. Now you will see Oracle Java ME SDK 3.2 in your Java Platform list.

    Read the article

  • BIP 10.1.3.4.x June 2010 Update Available

    - by Tim Dexter
    A new patchset for 10.1.3.4.0 and 10.1.3.4.1 is available on Metalink. some notes: The patch number is 9791839. This patchset includes 28 new bug fixes since the last patchset release on March 31. This is a culmulative update that includes all the fixes and enhancements from previous updates. The patch will supercede the other two updates. Install instructions are in the readme inside the patch There is also a new BIP client patch available, 9821068. No new template building features to my knowledge but there is an update to the template viewer to allow you to test and debug you siny new Excel templates. Server 8529759XMLP_TEMPLATE_DESIGNER CANNOT SAVE / UPLOAD TEMPLATE 8566455 BI PUBLISHER SCHEDULER DOES NOT START WITH JNDI DATA SOURCE 9295667RESPONSE OF GETSCHEDULEDREPORTINFO RETURNS STATUS AS 'UNKNOWN' INSTEAD OF 'SCHED 9542413 UNABLE TO CREATE A NEW TEMPLATE FROM UI 9546137 EXCEL ANALYZER TEMPLATE FAILS FOR A STRUCTURED XML WHEN IT IS UPLOADED 9556338 SIEBEL - BIP PARAMETERS SORT ORDER 9560562 BI PUBLISHER CACHE DIRECTORY FILLING UP AND POINTING TO INVALID DIRECTORY 9646599 USER ROLE DEFINED AS PRIMARYGROUP IN ACTIVEDIRECTORY GROUP ARE NOT RECOGNIZED 9664768 ER: NEED TO BIND USER ATTRIBUTE VALUES DEFINED IN ACTIVEDIRECTORY IN DATA QUERY 9665075 BI PUBLISHER AFTER 9546699 NOTIFICATIONS FOR REPORTS FAIL 9669973 ER: NEED TO SUPPORT PRE-PROCESSING XML WITH XSL FOR EXCEL TEMPLATE 9704401 ER: NEED TO SUPPORT DEFAULT GROUP FOR ALL USERS IN LDAP/AD SECURITY 9711899 SEARCH PARAMETER IS NOT VISIBLE WHEN SCHEDULE A REPORT 9753736 SOME ROLES FROM ACTIVEDIRECTORY ARE NOT LISTED IN ADMIN ROLE-FOLDER MAPPING 9771354 MULTIPLE PARAMETERS IN 10.1.3.4.1 DATA TEMPLATE ACT ACT DIFFERENTLY FROM 10.1.3. 9772982 "REFRESH OTHER PARAMETERS ON CHANGE" DOESN'T WORK PROPERLY Core  8599646 ER:EXTRA SPACE ADDED BELOW IMAGE IN A TABLE CELL OF TEMPLATE IN FIREFOX 9377593 SOME ROWS HEIGHT IN HTML/EXCEL OUTPUT ARE TOO BIG IN BI PUBLISHER 9487030 NAVIGATION TREE REPEATING TWICE IN PDF DCCUMENT CREATED BY BI PUBLISHER 9509432 PERFORMANCE ISSUE WHEN USING PDF TEMPLATE 9534424 PS: DOCUMENT-REPEAT-FULLPATH-ELEMENTNAME SHOULDNT USE DOT "." AS PATH SEPARATOR 9553360 FORMPROCESSOR CANNOT PARSE SOME PDF TEMPLATES 9554959 TEXT IN AUTOSHAPE IS NOT PROPERLY CUT OFF FOR LINE WRAPPING 9569417 AFTER APPLYING PATCH 9509432 PDF TEMPLATES WITH DBDRV PRODUCE NO OUTPUT 9571670 ER: EXCEL TEMPLATE TO SUPPORT XSLT LOGIC AND XSL CUSTOM EXTENTIONS 9589809 XSL:CALL-TEMPLATE IS MISSING IN GENERATED XSL FILE 9605920 BOOKMARK TESTCASE FAILED DUE TO ER9283933 9689634 PRINT FLOW CHART USING ACROSS 3 DOWN 0 GIVES EXTRA BLANK PAGES You might have noticed some fixes and ehancements to the Excel templates so I can get back on those now. There is a part two to the Mapviewer BIP Mashup coming ... just need aanother 4 hours in the day to squeeze it in.

    Read the article

  • MOSS 2007 WSP Retraction 'Error"

    - by juanlarios
    This one is a quick post , but I thought I would post this information as I could not find anything that helped me on this specific scenario. Please read the entire article before taking action as there are some irreversable or very troublesome routes I caution about! Problem: I had a client trying to retract a WSP from Central Admin and would eventually go to an, 'Error' State. I could not retract it and after looking at event logs I figured it was a problem with security. I tried several accounts, checked the databases to see if there was some issue with readonly databases and nothing was working.   Solution: Delete the solution from central admin! Yes, I said it. With StsAdm , just delete the solution from Central Admin using this command: "C:\Program Files\Common Files\Microsoft Shared\web server extensions\12\BIN\STSADM.exe" -o deletesolution -name "yoursolution.wsp" What has just happened is that Central Admin does not know about the WSP anymore but the feature and any deployed files are still on the server. For whatever reason SharePoint was not able to retract the files as it normally does. Now you can do one of two things, you can add the solution again to central admin and deploy overtop of the deployed files so it overrides them, or simply clean up the files manually. I re-added the solution through stsadm, but then deployed through stsadm using the -force option in the command. This overrides the existing files on the server. If you deploy through Central admin it will tell you you need the -force option that is not offered as part of the UI in central admin. Use the following command: "C:\Program Files\Common Files\Microsoft Shared\web server extensions\12\BIN\STSADM.exe" -o deploysolution -name "YourSolution.wsp" -immediate -allowgacdeployment -force Just to make sure everything was good, I retracted to solution again, and it worked! then I deleted the solution from central admin alltogether. Then I checked the server and noticed all the files that were deployed with the WSP were cleaned up properly. I then re-added the new WSP the client was looking to install (an Updated WSP). Conclusion: I have no idea why it was not able to retract, but I have seen this several times. I don't know if has to do with security of certain accounts. Althought it's anoying at times, it is fairly easy to fix if you have good instructions. Hope it helps you out!   ***WORD OF CAUTION - if you clean up the files manually you might want to uninstall the features through STSADM commands as SharePOint might still recognize the features that were deployed as the WSP. You might not want to get into the mess of deleting files that are still part of activated or installed Features. THis is why I suggest doing what I did.

    Read the article

  • February 2011 Java SE and Java for Business Critical Patch Update Released

    - by eric.maurice
    Hello, this is Eric Maurice again. Oracle released the February 2011 Critical Patch Update for Java SE and Java for Business today. As discussed in a previous blog entry, Oracle currently maintains a separate Critical Patch Update schedule for Java SE and Java for Business because of commitments made prior to the Oracle acquisition in regards to the timing for the publication of Java fixes. Today's Java Critical Patch Update includes fixes for 21 vulnerabilities. The most severe CVSS Base Score for vulnerabilities fixed in this CPU is 10.0, and this Base Score affects 8 vulnerabilities. Out of these 21 vulnerabilities, 13 affect Java client deployments. 12 of these 13 vulnerabilities can be exploited through Untrusted Java Web Start applications and Untrusted Java Applets, which run in the Java sandbox with limited privileges. One of these 13 vulnerabilities can be exploited by running a standalone application. In addition, one of the client vulnerability affects Java Update, a Windows-specific component. 3 of the 21 vulnerabilities affect client and server deployments. These vulnerabilities can be exploited through Untrusted Java Web Start applications and Untrusted Java Applets, as well as be exploited by supplying malicious data to APIs in the specified components, such as, for example, through a web service. 3 vulnerabilities affect Java server deployments only. These vulnerabilities can be exploited by supplying malicious data to APIs in the specified Java components. Note that one of these vulnerabilities (CVE-2010-4476) was the subject of a Security Alert released on February 8th. Finally, one of these vulnerabilities is specific to Java DB, a component in the Java JDK, but not included in the Java Runtime Environment (JRE). As usual, because of the severity of the vulnerabilities fixed in this Critical Patch Update, Oracle recommends that Java customers apply it as soon as possible. The Critical Patch Advisory provides more details about the vulnerabilities addressed in the Critical Patch Update as well as instructions on how to install the fixes and where to get them. Home users should use the Java auto-update mechanism to install the latest version of the Java Runtime Environment 6 update 24 or higher (JRE), which includes the fix for this vulnerability. For More Information: The Critical Patch Updates and Security Alerts page is located at http://www.oracle.com/technetwork/topics/security/alerts-086861.html More information on Oracle Software Security Assurance is located at http://www.oracle.com/us/support/assurance/index.html Consumers can go to http://www.java.com/en/download/installed.jsp to ensure that they have the latest version of Java running on their desktops. More information on Java Update is available at http://www.java.com/en/download/help/java_update.xml

    Read the article

  • Cannot get 3D OpenGL support in Vmware guests, how can I fix this?

    - by jjapol
    I have been working at this problem for 2 days now. I cannot for the life of me enable 3D support in VMWare 9 guests. My specifications are: Hardware: Dell Latitude E5520 laptop. Processor: Intel i7-2620M CPU @ 2.70GHz × 4. Memory: 8GB. Video: Intel Sandybridge Mobile x86/MMX/SSE2 OS: Ubuntu 12.04.1 LTS, 32 bit. Vmware Workstation: 9.0.1 build-894247 Glxgears functions fine. Frame rate is ~60fps. Vmware guest: Windows 7 Starting the Windows 7 guest in VMware throws the following errors: No 3D support is available from the host. and Hardware graphics acceleration is not available. I've read through this VMware forum thread, but again the hardware in the post is different (nVidia). I've followed the instructions at this Ask Ubuntu post as closely as possible as the question is nearly the same as mine although my hardware is different. Answer 1 regarding setting mks.gl.allowBlacklistedDrivers = TRUE; in my vmx configuration file causes the VM to crash when it starts. The second answer I followed as closely as possible. I uninstalled VMware, Did sudo apt-get install build-essential linux-headers-$(uname -r) at a terminal, Added the PPA https://launchpad.net/~glasen/+archive/intel-driver, Then at a terminal did sudo apt-get update && sudo apt-get upgrade -y I reinstalled VMware and have the same results: no 3D in guests. I'm getting the feeling that something is awry with the Sandy Bridge driver, but I can't seem to come up with any solutions. Has anyone out there run across this problem also? By the way, the operation of the likes of Solidworks and AutoCad within a Windpws 7 guest does appear to be improved in VMware 9 vs VMware 8 in spite of the fact that 3D support is lacking in the Windows 7 guest. I'd also add that my glxinfo file was nearly identical to the glxinfo file posted at askubuntu.com/questions/181829/…. I had a total of seven minor differences per a comparison using Meld. –

    Read the article

< Previous Page | 92 93 94 95 96 97 98 99 100 101 102 103  | Next Page >