Search Results

Search found 14777 results on 592 pages for 'clean installation'.

Page 97/592 | < Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >

• Windows 7 x64 installation freezes on new PC build

  - by jhsowter

  Symptoms While attempting to install Windows 7 (64 bit) on my new PC build, it freezes usually at the point where it is expanding the windows image, but has frozen as early as accepting the licence agreement, and as late as just after the first restart. My specs are at the bottom of the post. So far I have tried the following to identify the problem, in rough chronological order: Tried different hard drives with different sata cables. Same symptoms. I later used a different computer to install windows on the same hard drive with no problems. Tried the RAM in different slots, and tried one RAM stick instead of two. Same symptoms. Updated the BIOS to 1.60. Same symptoms. Ran Memtest86+ with RAM in dual channel. It passed about 6 times when I left it running overnight. Used USB to install windows instead of an optical drive. Same symptoms. Change SATA configuration from AHCI to IDE. Same symptoms. Tried various different SATA ports. Same symptoms. Updated BIOS to 1.70. Same symptoms. I saw the RAM did not list my motherboard as being supported even though the motherboard did list the RAM as being supported. So I tried some Kingston DDR3 1333MHz RAM instead. Same symptoms. Other (possibly) pertinent information My CPU idles at about 30 °C. I can't tell what it gets to when it's working. When I installed the CPU, the lever which locks the CPU in place took quite a bit of force to pull down. Now I didn't just yank it down without rechecking the CPU was seated properly about 5 times, but it does seems unusual, and I wonder if the CPU was seated badly if I would see these symptoms? I am out of ideas and don't know how to diagnose any further. I suppose either the motherboard or CPU must be the problem. I am on the verge of taking it to a specialist. The Question How should I proceed from here? Is there anything I can rule out as being the source of the symptoms I am seeing? My Specs CPU: Intel i5 3570k RAM: G.Skill RipjawsX 8GB kit HDD: single 3.5" 500GB SATA or 160GB 2.5" SATA (at different times and sometime together. But no RAID or anything). MB: ASRock Extreme4 Z77 PSU: Silverstone Strider Plus 600W ST60F-P

  Read the article

• CentOS 5.8 Server, manual install PHP 5.2.17

  - by Shiro

  I would like manually install PHP 5.2.17. I manage to install httpd and mysql. But when I want to PHP 5.2.17, I could not found a proper guide. These the step I had done with a fresh installation of CentOS 5.8 x86_64 (server & server GUI) yum install httpd httpd-devel /etc/init.d start OK /etc/init.d stop OK yum install mysql mysql-server mysql-devel yum remove php yum groupinstall "Development Tools" yum install libxml2-devel wget http://www.php.net/release/php5.2.17.zip to get php5.2.17 (client requirement must use this version) cd php5.2.17 ./configure --with-apxs2=/usr/sbin/apxs --with-mysql=/usr/local This is the area I confuse. I could not found the /usr/sbin/apxs in my system. I do another Google search on how to manually install PHP, they pointed using ./configure --with-apxs2=/usr/local/apache2/bin/apxs --with-mysql Both localtino I also cannot find apxs or apache2. I scare I make any mistake on it. Please help and guide on this. I am newbie in CentOS

  Read the article

• Restarting Hudson - Windows Installation

  - by Toggo

  Whenever I update/install a new plugin or update hudson. Once the new plugin/update has been installed a button appears "Restart when no jobs are running." If I click this button hudson appears to try to restart but then just hangs. Has anyone else experienced this? Can hudson be forced to restart another way? I've tried restarting the service but this has no effect. I've asked this question over at stack overflow, so will update this if I get an answer from there. Thanks Tom

  Read the article

• Internet connection & IIS stopped on windows xp after VMware server 2 installation

  - by Eduardo Xavier

  Hi, I'm running a local network. My IP ranges from 192.168.1.2 to 192.168.1.15. All IP are static ones. And my router's IP is 192.168.1.1 and I provide it as default gateway and preferred DNS server on client machines. Everything worked fine on this scenario. I could use internet and reach services on other machines. BUT I have installed VMware server 2 on the windows XP to host windows 2003 Virtual Machine (VM). I set the following configuration: Windows XP's => 192.168.1.11. Windows 2003 => 192.168.1.12. (virtual machine) This approach worked just fine as it used to work with Microsoft Virtual PC. I can access mysql & IIS websites on the windows 2003 virtual machine. BUT two things doesn't work anymore on the Windows XP: internet connection - but I can see the MAC address on the wireless router IIS - Ping on 127.0.0.1 it's ok as I can hit localhost:8222 nor localhost Does anyone knows how to fix any of this? (at least the internet connection)

  Read the article

• Where is vmlinux on my Ubuntu installation?

  - by Jason Baker

  I'm trying to work with starting up oprofile, and I'm running into a problem at this step: opcontrol --vmlinux=/path/to/vmlinux Ubuntu has no package called vmlinux, and when I do a locate vmlinux, I get a lot of files: /usr/src/linux-headers-2.6.28-14/arch/h8300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-14/arch/m68k/kernel/vmlinux-std.lds /usr/src/linux-headers-2.6.28-14/arch/m68k/kernel/vmlinux-sun3.lds /usr/src/linux-headers-2.6.28-14/arch/mn10300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-14/arch/sh/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-14/arch/x86/boot/compressed/vmlinux_32.lds /usr/src/linux-headers-2.6.28-14/arch/x86/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-14/include/asm-generic/vmlinux.lds.h /usr/src/linux-headers-2.6.28-15/arch/h8300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-15/arch/m68k/kernel/vmlinux-std.lds /usr/src/linux-headers-2.6.28-15/arch/m68k/kernel/vmlinux-sun3.lds /usr/src/linux-headers-2.6.28-15/arch/mn10300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-15/arch/sh/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-15/arch/x86/boot/compressed/vmlinux_32.lds /usr/src/linux-headers-2.6.28-15/arch/x86/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-15/include/asm-generic/vmlinux.lds.h /usr/src/linux-headers-2.6.28-16/arch/h8300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-16/arch/m68k/kernel/vmlinux-std.lds /usr/src/linux-headers-2.6.28-16/arch/m68k/kernel/vmlinux-sun3.lds /usr/src/linux-headers-2.6.28-16/arch/mn10300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-16/arch/sh/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-16/arch/x86/boot/compressed/vmlinux_32.lds /usr/src/linux-headers-2.6.28-16/arch/x86/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-16/include/asm-generic/vmlinux.lds.h Which one of these is the one I'm looking for?

  Read the article

• Cannot find my hard disk while installing linux-“No root file system defined” error

  - by Syam Kumar S

  I am trying install Linux on my computer (tried Ubuntu 10.4 and Linux Mint 9). I started the installation wizard and on the hard disk selection page the hard disk is not displayed. I have a 500GB disk with 5 partitions and windows 7 ultimate in one partition. If I click the forward button, it shows an error- "No root file system defined". I have tried to install by booting from CD and pendrive but both shows the same error. When I load Linux as live CD it doesn't show the hard disk. My hard disk works fine in windows 7. System config: intel i3 2100, 500GB hdd, 2GB ram

  Read the article

• Macports irssi & perl5 installation issues

  - by Dmitri DB

  Long time reader, first time poster. Big, appreciative thanks for everyone's collective questioning and answering here and at stackoverflow, it's helped me quite a lot over the time I've been learning answers through these sites! Apologies in advance if I didn't search hard enough on posts already up on this site to find out what I could do about this issue, but I thought I'd just reach out for the sake of trying at least once. I've experienced this issue while starting up my macports-installed version of irssi: 13:25 -!- Irssi: Error in script dispatch: 13:25 Can't locate lib.pm in @INC (@INC contains: /opt/local/lib/perl5/site_perl/5.12.4/darwin-multi-2level /opt/local/lib/perl5/site_perl/5.12.4 /opt/local/lib/perl5/vendor_perl/5.12.4/darwin-multi-2level /opt/local/lib/perl5/vendor_perl/5.12.4 /opt/local/lib/perl5/5.12.4/darwin-multi-2level /opt/local/lib/perl5/5.12.4 /opt/local/lib/perl5/site_perl/5.12.3/darwin-multi-2level /opt/local/lib/perl5/site_perl/5.12.3 /opt/local/lib/perl5/site_perl /opt/local/lib/perl5/vendor_perl .) at (eval 18) line 1. 13:25 BEGIN failed--compilation aborted at (eval 18) line 1. 13:25 Huh, strange. I looked into it a bit: [email protected] /opt/local/lib/perl5 ?- find . -name "lib.pm" -ls 14673887 16 -r--r--r-- 1 root admin 6853 25 Jun 23:39 ./5.12.4/darwin-thread-multi- 2level/lib.pm [email protected] /opt/local/lib/perl5 ?- l 5.12.4/darwin-thread-multi-2level total 1864 drwxr-xr-x 55 root admin 1870 28 Jun 19:28 . drwxr-xr-x 158 root admin 5372 28 Jun 19:28 .. -rw-r--r-- 1 root admin 177814 25 Jun 23:39 .packlist drwxr-xr-x 6 root admin 204 28 Jun 19:28 B -r--r--r-- 1 root admin 25714 25 Jun 23:39 B.pm drwxr-xr-x 64 root admin 2176 28 Jun 19:28 CORE drwxr-xr-x 3 root admin 102 28 Jun 19:28 Compress -r--r--r-- 1 root admin 3000 25 Jun 23:39 Config.pm -r--r--r-- 1 root admin 228094 25 Jun 23:39 Config.pod -r--r--r-- 1 root admin 409 25 Jun 23:39 Config_git.pl -r--r--r-- 1 root admin 38759 25 Jun 23:39 Config_heavy.pl -r--r--r-- 1 root admin 21174 25 Jun 23:39 Cwd.pm -r--r--r-- 1 root admin 63535 25 Jun 23:39 DB_File.pm drwxr-xr-x 3 root admin 102 28 Jun 19:28 Data drwxr-xr-x 5 root admin 170 28 Jun 19:28 Devel drwxr-xr-x 4 root admin 136 28 Jun 19:28 Digest -r--r--r-- 1 root admin 25185 25 Jun 23:39 DynaLoader.pm drwxr-xr-x 22 root admin 748 28 Jun 19:28 Encode -r--r--r-- 1 root admin 29731 25 Jun 23:39 Encode.pm -r--r--r-- 1 root admin 6736 25 Jun 23:39 Errno.pm -r--r--r-- 1 root admin 5445 25 Jun 23:39 Fcntl.pm drwxr-xr-x 5 root admin 170 28 Jun 19:28 File drwxr-xr-x 3 root admin 102 28 Jun 19:28 Filter -r--r--r-- 1 root admin 1819 25 Jun 23:39 GDBM_File.pm drwxr-xr-x 4 root admin 136 28 Jun 19:28 Hash drwxr-xr-x 3 root admin 102 28 Jun 19:28 I18N drwxr-xr-x 11 root admin 374 28 Jun 19:28 IO -r--r--r-- 1 root admin 1404 25 Jun 23:39 IO.pm drwxr-xr-x 6 root admin 204 28 Jun 19:28 IPC drwxr-xr-x 4 root admin 136 28 Jun 19:28 List drwxr-xr-x 4 root admin 136 28 Jun 19:28 MIME drwxr-xr-x 3 root admin 102 28 Jun 19:28 Math -r--r--r-- 1 root admin 2519 25 Jun 23:39 NDBM_File.pm -r--r--r-- 1 root admin 4208 25 Jun 23:39 O.pm -r--r--r-- 1 root admin 15563 25 Jun 23:39 Opcode.pm -r--r--r-- 1 root admin 21011 25 Jun 23:39 POSIX.pm -r--r--r-- 1 root admin 58962 25 Jun 23:39 POSIX.pod drwxr-xr-x 5 root admin 170 28 Jun 19:28 PerlIO -r--r--r-- 1 root admin 2515 25 Jun 23:39 SDBM_File.pm drwxr-xr-x 4 root admin 136 28 Jun 19:28 Scalar -r--r--r-- 1 root admin 10837 25 Jun 23:39 Socket.pm -r--r--r-- 1 root admin 41003 25 Jun 23:39 Storable.pm drwxr-xr-x 4 root admin 136 28 Jun 19:28 Sys drwxr-xr-x 3 root admin 102 28 Jun 19:28 Text drwxr-xr-x 5 root admin 170 28 Jun 19:28 Time drwxr-xr-x 3 root admin 102 28 Jun 19:28 Unicode -r--r--r-- 1 root admin 14462 25 Jun 23:39 attributes.pm drwxr-xr-x 38 root admin 1292 28 Jun 19:28 auto -r--r--r-- 1 root admin 19892 25 Jun 23:39 encoding.pm -r--r--r-- 1 root admin 6853 25 Jun 23:39 lib.pm -r--r--r-- 1 root admin 11044 25 Jun 23:39 mro.pm -r--r--r-- 1 root admin 997 25 Jun 23:39 ops.pm -r--r--r-- 1 root admin 13945 25 Jun 23:39 re.pm drwxr-xr-x 3 root admin 102 28 Jun 19:28 threads -r--r--r-- 1 root admin 33283 25 Jun 23:39 threads.pm So, it sort of seems to me that the permissions which perl5 got installed with for these modules has gotten mixed up somehow? I'm not really a perl user beyond enjoying it for massive directory-recursive find/replace operations within text files, so I haven't much of an idea what the permissions here are supposed to look like, and I'm not really sure how to go about determining how macports has gone and installed perl this way when it's otherwise worked without failure for years now. Does anyone have any recommendations for the sanest path towards rectifying this issue? Also, is there any interesting reason as to why the macports default for the perl5 port installs 5.12.4, and not 5.16.0, which has to be explicitly installed via the perl5.16 port? Thanks again!

  Read the article

• Error: Cannot find a valid baseurl for repo: updates in ffmpeg installation

  - by athomas14super

  Hi I have problem installing ffmpeg. I follow this url: https://www.crucialp.com/resources/tutorials/server-administration/how-to-install-ffmpeg-ffmpeg-php-mplayer-mencoder-flv2tool-LAME-MP3-Encoder-libog.php Setting up repositories core 100% |=========================| 1.1 kB 00:00 rpmforge 100% |=========================| 1.1 kB 00:00 Error: Cannot find a valid baseurl for repo: updates [root@02e7709 src]# yum install subversion ruby ncurses-devel Loading "installonlyn" plugin Setting up Install Process Setting up repositories core 100% |=========================| 1.1 kB 00:00 rpmforge 100% |=========================| 1.1 kB 00:00 Error: Cannot find a valid baseurl for repo: updates [root@02e7709 src]# svn checkout svn://svn.mplayerhq.hu/ffmpeg/trunk ffmpeg -bash: svn: command not found [root@02e7709 src]# svn command not found and throws error Error: Cannot find a valid baseurl for repo: updates I am installing in fedora core 6 64 bit

  Read the article

• lsphp5 memcache extension installation problem

  - by mishu

  I am trying to recompile litespeed php with parameter '--enable-memcache' but getting an error: configure: WARNING: unrecognized options: --enable-memcache how to get it working?

  Read the article

• Windows 7 Upgrade from an OEM disc

  - by user1026361

  I recently bought a new laptop with Windows 7 Home Premium and a Windows 7 Pro Upgrade key. It also comes with a cavalcade of bloatware. I would like to start with a fresh install of Windows. I understand that I can upgrade to W7Pro using the option in the Home Premium Start menu. However, I also own a Windows 7 Pro OEM installation disc from another computer. Can I use this Windows 7 Pro OEM disc to install Windows, and when it asks me for my key, provide the upgrade key purchased? Or am i required to install Home Premium first and then apply my upgrade key?

  Read the article

• Windows XP SP3 install keeps rebooting

  - by TerryR

  The base fonts on my Windows XP Pro were corrupted. A suggested fix was to "install" XP again, essentially just to overwrite the WINNT folder hence resetting all the fonts. I downloaded the XP Pro SP3 installer from our corporate MSDN account, ran it straight from the HDD and at the very end it crashed and rebooted. Now it just keeps rebooting over and over after saying "Continuing installation...." I can't boot in Safe Mode, I can't get to a command prompt or anything. I'm out of ideas. Formatting the drive and performing a fresh install is NOT an option.

  Read the article

• Gitosis installation error

  - by Abhinav

  I am trying to install gitosis on my server but keep getting the error "Username contains not allowed characters" sudo -H -u git gitosis-init < /tmp/id_rsa.pub with the username "[email protected]". Any fix for this?

  Read the article

• Live Mesh starts exactly once on fresh Win7 Ultimate installation

  - by Reb.Cabin

  I did a fresh install of Windows 7 Ulimate 64-bit on a formatted drive on a refurbed Lenovo PC, applied all 102 (!) windows updates, windows seems to be working fine. No quirks installing, no apps, no junkware, just straight, legal, Win7 Ultimate right from an unopened 2009 Microsoft box. Ok, breathe sigh -- Install Live Mesh (no messenger, no mail, no writer, no photo, none of the rest of the Windows Live freeware). Set up my shares, let it run overnight. watch MOE.exe in the Task-Manager perf pane to make sure it's all settled down. reboot. Ok, check that MOE is running and files are getting updated properly from other machines in the mesh. Great. HOWEVER -- when I try to launch Windows Live Mesh app from the Start jewel, I get a brief hourglass, then nothing. Reboot. Same story. result -- the shares I already posted seem to be synching properly, but I can't run the app, so I can't add and delete shares. The background process MOE seems to run, but I can't get the app going. btw, the reason I did this fresh install is I had exactly the same experience running Vista, so I wiped the machine hoping it would solve this nasty problem. Imagine my surprise! Will be grateful for clues, advice, etc, please & thanks!

  Read the article

• Error during installation of Mesa on Linux

  - by rodnower

  Hello, I have a problem. I try to install Mesa 7.8 on CentOS 3.9 for i386 on VMVare 7.0.1 like described here: http://linux-sxs.org/multimedia/mesa.html When I perform configuration stage: ++++++++++++++++++++++++++++++++++++++++++++++++++ [root@CentOS Mesa-7.8]# ./configure --prefix=/usr --sysconfdir=/etc ++++++++++++++++++++++++++++++++++++++++++++++++++ (root is actualy root) This is what I get: ++++++++++++++++++++++++++++++++++++++++++++++++++ . . . checking pkg-config files for X11 are available... no checking for X... no configure: error: X11 development libraries needed for dri driver ++++++++++++++++++++++++++++++++++++++++++++++++++ (Three dots says that there is some output before) Put attention to error. Any idea? Thank you very much forahead.

  Read the article

• Best way to restore individual folders via Time Machine after clean Lion install?

  - by A4J

  I'm doing a clean erase and install of Lion, and am looking for the best way to restore individual folders into my home directory via Time Machine. I've done a dummy run, clean Lion install, then 'browse other disks' in Time Machine, navigate to my home folder and 'restore' what I need, such as pictures/music and folders inside the .library folder (such as Mail and Keychains). However this method seems to give you odd permissions, like this: http://i43.tinypic.com/15y82v4.png Hence I wondered if anyone knows what the best method is to restore files and folders after a clean install. N.b I do not want to use the migration assistant, or 'restore OS from Time Machine' - as I specifically want to do a clean install, and just copy over what I need (some folders will be moved onto a separate disk to the OS, and some will remain on the same disk). Thanks in advance.

  Read the article

• "Disk boot failure" error after installing Windows 7 on SSD

  - by Tony_Henrich

  I have a system with 3 SATA drives which runs fine. Got a new SSD drive and wanted to install a fresh Windows-7 on it. So I removed the boot drive and replaced it with the SSD drive. Installed Windows and when it was done, rebooted and now I get "Disk boot failure. Insert system disk and press enter" error message. I reinstall again and still same message. Removed the SSD and put back the original drive and I got the same message!! I checked the BIOS and things look good. Something is wrong. Two questions: 1- Why isn't the new Windows booting from the SSD? 2- Why isn't the machine booting using the previous working configuration anymore, after removing the SSD? I did connect it during the second Windows installation but it was the last drive in the SATA connector. Would Windows installer mess with its MBR sector?

  Read the article

• Dell Vostro 1000 w/fresh XP Pro installation running very slow

  - by Ssvarc

  I'm working on a Dell Vostro 1000 laptop. It was running slowly and hanging, antivirus scans turned up nothing and the same with the Dell diagnostics (DFT hung - but Dell's diagnostics gave the HD a pass) so I imaged the HD and installed XP Pro on it. The laptop is still slow! (It takes a noticeable delay to enter words into the Google search box in IE and the computer hangs every time it enters the XP screensaver.) What are the likely possibilities at this point and how would I go about checking for them?

  Read the article

• Nexus functionality is limited after installation

  - by Dmitriy Sukharev

  I have a CentOS based server with Sonatype Nexus 2.0.4-1 installed. The issue is that there are no standard "Artifact Search", "Advanced Search", "Browse Index", "Refresh Index" Nexus features, as well as Artifact Information tab after selection of any artifact (only Maven Information tab). I tried to Google, but was amazed that there're no information about this issue. Actually it looks like all actions I've done are: wget http://www.sonatype.org/downloads/nexus-2.0.4-1-bundle.tar.gz tar -xvf nexus-2.0.4-1-bundle.tar.gz cp -r nexus-2.0.4-1 sonatype-work /opt/ ln -s /opt/nexus-2.0.4-1/* /opt/nexus ln /opt/nexus/bin/nexus /etc/init.d/ chmod 755 /etc/init.d/nexus vim /etc/init.d/nexus NEXUS_HOME=“/opt/nexus” RUN_AS_USER=“nexus” useradd -s /sbin/nologin -d /var/lib/nexus nexus chown -R nexus /opt/nexus/ chown -R nexus /opt/nexus-2.0.4-1/ sudo -u nexus cp /opt/nexus/conf/examples/proxy-https/jetty.xml /opt/nexus/conf/ To force Nexus be available through HTTPS I went to Administration - Server - Application Server Settings as admin and changed Base URL to https:// external IP/nexus and set Force Base URL to true. Any ideas how to get missed Nexus features?

  Read the article

• Error in Installing MediaWiki for Ubuntu, Posgres 8.3

  - by Masi

  How can you solve the error message at the last line? .... # Installing MediaWiki with php file extensions # Environment checked. You can install MediaWiki. # Generating configuration file... # Database type: PostgreSQL # Loading class: DatabasePostgres # Attempting to connect to database "wikidb" as "wikiuser"... error: No database connection # Checking the version of Postgres... Warning: pg_version(): supplied argument is not a valid PostgreSQL link resource in /var/www/wiki/includes/db/DatabasePostgres.php on line 1078 FAILED. Required version is 8.1. You have 7.3 or earlier I am using Postgres 8.3 which makes the error message strange. The file "LocalSettings.php" was not created to the directory config so I cannot continue the installation without solving the problem.

  Read the article

• Run a BitLocker protected Windows 7 installation on VirtualBox from physical drive

  - by djechelon

  I have a broken laptop with its hard drive intact. I'll be getting it repaired in a few days but I must continue my work possibly uninterrupted, so I chose to run the OS in another working laptop (I can't just transfer documents). My question is really simple: Can I create a virtual machine in VirtualBox (under Linux) that uses the physical hard drive mentioned above which is encrypted with BitLocker? I have the restore key at hand, of course. I wouldn't like to mount the hard disk as primary hard disk for laptop (and run 7 as primary OS), but that could be the final choice if virtualizing is not an option. Thank you.

  Read the article

• Specifying network settings during SLES 11 auto installation

  - by banjer

  I'm setting up an autoinst.xml file for auto-installing SLES 11. I get prompted for the various interface settings per below, but they don't seem to stick once the server reboots. I don't think I have the xml defined correctly. I'm hoping someone has experience with this. <ask-list> <ask> <path>networking,dns,hostname</path> <question>Enter Hostname (server name)</question> <stage>initial</stage> <default>merkin</default> </ask> <ask> <path>networking,interfaces,interface,0,device</path> <question>Enter the primary ethernet device:</question> <stage>initial</stage> <default>eth0</default> </ask> <ask> <path>networking,interfaces,interface,0,ipaddr</path> <question>Enter the primary IP Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,interfaces,interface,0,netmask</path> <question>Enter the Netmask Address:</question> <stage>initial</stage> </ask> <ask> <path>networking,routing,routes,route,0,gateway</path> <question>Enter the primary Gateway Address:</question> <stage>initial</stage> </ask> </ask-list> The first one for hostname seems to be sticking just fine, but the rest do not. As an alternative, is there a way to stop the autoinstall at the section where you configure the network devices so that the user can take over? I was able to show the partition proposal, but not sure how to do the same with the networking setup.

  Read the article

• Installation of gearmand fails on libevent dependency

  - by PeeHaa

  I've installed the PostgreSQL yum repo and have PostgreSQL running for some time now, but now when I try to install gearmand I get the following errors: Transaction Check Error: file /usr/bin/event_rpcgen.py from install of compat-libevent14-1.4.13-1.rhel6.x86_64 conflicts with file from package libevent-devel-2.0.12-1.rhel6.x86_64 file /usr/lib64/libevent_core.a from install of compat-libevent14-1.4.13-1.rhel6.x86_64 conflicts with file from package libevent-devel-2.0.12-1.rhel6.x86_64 file /usr/lib64/libevent_core.so from install of compat-libevent14-1.4.13-1.rhel6.x86_64 conflicts with file from package libevent-devel-2.0.12-1.rhel6.x86_64 file /usr/lib64/libevent_extra.a from install of compat-libevent14-1.4.13-1.rhel6.x86_64 conflicts with file from package libevent-devel-2.0.12-1.rhel6.x86_64 file /usr/lib64/libevent_extra.so from install of compat-libevent14-1.4.13-1.rhel6.x86_64 conflicts with file from package libevent-devel-2.0.12-1.rhel6.x86_64 This is because the libevent is coming from the postgresql repository, so I thought I just disable the postgresql repository and try again: yum --disablerepo=pgdg91 install gearmand Error: Package: gearmand-0.14-3.el6.2.x86_64 (epel) Requires: libevent-1.4.so.2()(64bit) Available: libevent-1.4.13-1.el6.x86_64 (base) libevent-1.4.so.2()(64bit) Installed: libevent-2.0.12-1.rhel6.x86_64 (@pgdg91) Not found Is there a way to keep the libevent version used by postgresql and at the same time install gearmand (with the correct libevent version)?

  Read the article

• minimal rsync installation on windows xp?

  - by Aman Jain

  Hi I want to install rsync on windows xp. I have searched the web, but most of the solutions suggest using cygwin, but is there any other way to do this? I don't want to install cygwin because it takes lot of space. Moreover, I need to make it communicate with a rsync daemon on Linux, therefore alternatives to rsync on windows won't help. Thanks

  Read the article

• Why is this APC installation failing so badly?

  - by Matt

  I have multiple instances of APC running on my server with similar configurations (albeit with different cache sizes. However, one of the instances is performing extremely poorly, and I have no idea why (100% cache fragmentation, high miss rate). The runtime settings I'm using are as follows (pretty much out of the box): apc.cache_by_default 1 apc.canonicalize 1 apc.coredump_unmap 0 apc.enable_cli 0 apc.enabled 1 apc.file_md5 0 apc.file_update_protection 2 apc.filters apc.gc_ttl 3600 apc.include_once_override 0 apc.lazy_classes 0 apc.lazy_functions 0 apc.max_file_size 1M apc.mmap_file_mask apc.num_files_hint 1000 apc.preload_path apc.report_autofilter 0 apc.rfc1867 0 apc.rfc1867_freq 0 apc.rfc1867_name APC_UPLOAD_PROGRESS apc.rfc1867_prefix upload_ apc.rfc1867_ttl 3600 apc.shm_segments 1 apc.shm_size 10M apc.slam_defense 1 apc.stat 1 apc.stat_ctime 0 apc.ttl 0 apc.use_request_time 1 apc.user_entries_hint 4096 apc.user_ttl 0 apc.write_lock 1 APC is version 3.1.6, PHP is 5.3.3-1ubuntu9.5. I've tried restarting Apache multiple times, so this isn't a freak instance. The instance with problems is simply running Wordpress with a few plugins installed. All other instances (~4) on the server are running perfectly fine with almost 100% hit rates and 0% fragmentation; for example this instance is holding a website built using the Symfony framework. Any help would be much appreciated; I haven't had much experience with APC and was hoping for it to be an out-of-the-box speed boost ;).

  Read the article

• .NET 3.5 installation comes up with Error 0x800F0906, then 0x800F0081F using dism

  - by Austin Meadows

  I've recently tried installing .NET 3.5 for an application on Windows 8.1. I used the OS's popup thing to download/install .NET 3.5 and always get error code 0x800F0906. Upon further research, I found I would have to pop in my Windows 8 CD and install it with this command, where "E:\" is where my CD is mounted: Dism /online /enable-feature /featurename:NetFx3 /All /Source:E:\sources\sxs /LimitAccess This and any derivative of it (e.g., removing /LimitAccess) has not worked for me and has either given me the same error code (0x800F0906) or a different one, 0x800F0081F. I've even copied the sxs folder to my hard drive, just in case something was going on with the CD Drive, only to have the same results. In that case, I used this command line: Dism /online /enable-feature /featurename:NetFx3 /All /Source:C:\dotnet35 /LimitAccess I find this surreal because in both cases, the files are indeed there but the program thinks it's not. Here's the CBS.log file. Any ideas on how to fix this? Any help is very appreciated :) EDIT: I now have a proper dism.log file, I'm not sure what happened to the last one or why it did that. Here's the link to the new log file. It's interesting to note that it doesn't recognize some of the commands in the script such as "featurename" or "source".

  Read the article

< Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >