Search Results

Search found 6288 results on 252 pages for 'credit card'.

Page 97/252 | < Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >

• How to reduce the fan noise and how to increase battery life in ubuntu 11.10/12.04?

  - by mehdi

  I have a brand new Sony Vaio S series laptop.(VPCSA2DGX) It came factory installed with Windows 7 professional Edition 64bit. Runs Intel core i5, 500 GB HDD , 4GB Ram. First I installed ubuntu 11.10 64 bit along side Windows to dual boot. Later,since the problem did not solve, I installed ubuntu 12.04 64bit along side Windows to dual boot. However the problem keeps annoying me. Problem: When running ubuntu 11.10/12.04, the battery lasts only about 1.5 hours. The Fan runs loud and continuously. And there is a lot of heat generated. System monitor shows less than 5% CPU used. My laptop enjoys hybrid graphic and I tried turning off ADM graphic card and keep Intel graphic card on. However I can not get the Fan noise or heat to go away and consequently the battery drain continues. BTW, in windows, the laptop gives 4-5 hours of battery power, Fan is silent and there is no heat problem. Any ideas on how to reduce the fan noise and how to increase battery life in ubuntu 11.10/12.04?

  Read the article

• How do I install the EW-7318Ug wireless drivers?

  - by user69731

  I'm on Ubuntu 12.04 and I need to install & configure Internet connection. I want to use montor mode in Wireshark. After Ubuntu installation my wireless card was recognized but it doesn't connect to the Internet. Internal wireless card works well. What should I do? I'm new to Linux. PC:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 64:31:50:0f:d4:70 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x8000 eth1 Link encap:Ethernet HWaddr e0:2a:82:aa:2d:3e inet addr:192.168.0.101 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::e22a:82ff:feaa:2d3e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:20978 errors:0 dropped:0 overruns:0 frame:364651 TX packets:20949 errors:171 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:19299119 (19.2 MB) TX bytes:3024858 (3.0 MB) Interrupt:19 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4788 errors:0 dropped:0 overruns:0 frame:0 TX packets:4788 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:387017 (387.0 KB) TX bytes:387017 (387.0 KB) wlan1 Link encap:Ethernet HWaddr 00:1f:1f:44:c1:a4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10508 errors:0 dropped:0 overruns:0 frame:0 TX packets:6143 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14831319 (14.8 MB) TX bytes:644606 (644.6 KB) PC:~$ iwconfig lo no wireless extensions. wlan1 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:225 Noise level:162 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions.

  Read the article

• 12.04 GPU lockup

  - by soandos

  I was able to install Ubuntu 12.04 using the alternative version of the image, (64 bit) but when I start the system it tells me the GPU locked up, and instead presents a text only screen. I understand that this site is not for bug reports, but at the same time, I know that there are some versions of the installer than have to be compatible with my graphics card (Nvidia GTS 360M). I assumed that the mere fact that the alternative installer ran was an indication that I could get some sort of graphical interface running after the install. Is there some way of getting some type of graphical interface running on my machine? Even better would be is there a way to get the rest of the system running as normal (i.e. GPU up and running)? If an internet connection is required to download driver support or something similar, directions for how to configure a wireless connection with WPA2-Personal protection from the text-only interface (bash). Any help would be appreciated. Note: I was able to find this which tells me that the card is supported. Note 2: In the install software stage of the install, I was unable to install anything (no internet connection) Update: The exact error message is [8.591394] [drm] 0000:01:00.0: GPU Lockup - switching to software fbcon Update 2: If I try to install with the regular version of Ubuntu, the screen goes staticy. This also happens if I install with Wubi (distasteful I know) and then try to use Ubuntu. Update 3: I've tried xforcevesa, nomodeset and xforcevesa nomodeset as my wubi boot options. Update 4: Thanks to jokerdino, I can now connect to the internet, so internet tools would now be a possibility.

  Read the article

• Internet is far slower in Ubuntu than Windows 7 on dual-booted machine

  - by Tim

  Edit: I'll leave the original post as-is, but after further investigation, it appears that the problem is something to do with my wi-fi card. Speeds are normal when I connect via cable. Edit 2: Problem was solved. It was something to do with the wireless card drivers. I normally use Windows 7 on my laptop and have internet speeds that are normally about 15-20 Mb/s. I have recently dual-booted with Ubuntu 12.10, and have noticed that internet speeds are drastically slower in Ubuntu. When tested, speeds range from 0.2-2 Mb/s, although occasionally being significantly faster than that or even stopping completely for short periods of time. I've also noticed that when first booting into Ubuntu, speeds start fairly fast, and drop to incredibly slow with a few seconds to a few minutes. There's still some possibility that the issue may be with my ISP, as things seem slower than usual even in Windows, but I suspect that it is related to Ubuntu, as things are far slower in Ubuntu than in Windows. I'm wondering, what could be the cause of this? Potentially relevant information: -I've dual booted before on this machine with earlier versions of Ubuntu (different ISP at the time) with no problem. ISP: Rogers (Major Canadian ISP) System info (Gateway NV53a Laptop): Operating System MS Windows 7 Home Premium 64-bit CPU AMD Phenom II N970 Caspian 45nm Technology RAM 6.00 GB Dual-Channel DDR3 @ 664MHz (9-9-9-24) Motherboard Gateway SJV51_DN (Socket S1G4) Graphics Generic PnP Monitor (1366x768@60Hz) ATI Mobility Radeon HD 4250 (Acer Incorporated [ALI]) Hard Drives 733GB TOSHIBA TOSHIBA MK7559GSXP ATA Device (SATA) Networking info: Connected through Wi-Fi Atheros AR5B97 Wireless Network A

  Read the article

• Correct nvidia+intel graphics setup in 14.04

  - by Espressofa

  Just upgraded to 14.04 to try to fix some other issues. Now, something has gone wrong with my graphics. I have a Thinkpad T530 with Intel and Nvidia graphics cards. $ inxi -SGx System: Host: xyz Kernel: 3.13.0-24-generic x86_64 (64 bit, gcc: 4.8.2) Desktop: N/A Distro: Ubuntu 14.04 trusty Graphics: Card-1: Intel 3rd Gen Core processor Graphics Controller bus-ID: 00:02.0 Card-2: NVIDIA GF108M [NVS 5400M] bus-ID: 01:00.0 X.Org: 1.15.1 drivers: fbdev,vesa,intel,nouveau (unloaded: nvidia) Resolution: [email protected] GLX Renderer: N/A GLX Version: N/A Direct Rendering: N/A $ glxinfo name of display: :0 Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Error: couldn't find RGB GLX visual or fbconfig Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". Xlib: extension "GLX" missing on display ":0". I'm not sure what I did but now something is wrong with my graphics, as should be visible from the above commands. nvidia-detector says "none" as well. I used to have bumblebee but then some website said to remove it and now something's clearly wrong. What's the right way to set things up? Should I try to add bumblebee back? Here's what's installed now: $ dpkg --get-selections | grep nvidia nvidia-319 install nvidia-331 install nvidia-libopencl1-331 install nvidia-opencl-icd-331 install nvidia-prime install nvidia-settings install nvidia-settings-319 install

  Read the article

• Fix for poor hd playback for 11.04 upwards

  - by mark kirby

  Hi guys ive seen loads of posts on this site about poor 720/1080p playback in recent ubuntu versions I had this problem and fixed it so I thought id share it with everyone.... 1 install mplayer 2 install smplayer frontend {in software center} 3 open smplayer 4 go to "OPTIONS" then "PREFRENCES" then "GENRAL" 5 if you have a nvidia card choose "OUTPUT DRIVER" and select "VDPAU" {for ATI or AMD choose xv (0 - ATI Radeon AVIVO video) I dont know if this will work as my card is nvidia but it should) 6 go to performance on the left hand side and set both local and streaming cache to 99999 (this may also fix dvd playback if you set that cache aswell} 7 check the box for "ALLOW HARD FRAME DROP" and set "LOOP FILTER" to skip only on HD 8 Set the "THREDS FOR DECODING OPTION TO THE NUMBER OF CORES YOUR CPU HAS IF YOU HAVE MORE THAN ONE CPU ADD UP ALL THE CORES FOR BEST PERFORMANCE" 9 Enjoy you HD movies again on ubuntu...... I have a pretty avrage machine heres my spec.... 2x Pentium 4 ht 3 ghz Stock dell power and motherboard GFORCE 310 HDMI 24 inch full HD tv as a monitor so any one with dule core cpu should have no problems getting this to work. hope this helps someone out.

  Read the article

• Unable To Get Sound Working to External Speaker on HP TouchSmart 320 on 11.04 or 11.10

  - by Schof

  This is an HP TouchSmart 320, model number 320-1200m. I'm using Ubuntu 11.04. Hardware information: root@hp320:/home/mpower# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Generic [HD-Audio Generic], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 root@hp320:~$ cat /proc/asound/card0/codec#0 | grep Codec Codec: IDT 92HD91BXX Sound to headphone jack works properly, but sound to built-in speakers does not work. I have installed Windows, and with Windows 7 installed, all audio hardware works properly, so this isn't a hardware fault. I've looked at https://help.ubuntu.com/community/HdaIntelSoundHowto and have been unable to find my card in http://www.kernel.org/doc/Documentation/sound/alsa/HD-Audio-Models.txt . I have tried adding almost every conceivable model in the line "options snd-hda-intel model=MODEL" line I added to /etc/modprobe.d/alsa-base.conf. Update 2011-11-09 2:31 PM PST: I've gone to Control Center - Sound Preferences to attempt settings that make sound work. The "Hardware" tab shows one device: "Internal Audio 1 Output / 1 Input Analog Stereo Duplex." There are two output profiles listed in the selection box at the bottom of the tag: Analog Stereo Duplex and Analog Stereo Output. Neither cause sound to emit from the speakers. I've also run alsamixer on the command-line and ensured that everything is set to maximum and nothing is muted. Update 2011-11-09 5:15 PM PST: I've replicated the exact same symptoms in 11.10. Update 2011-11-10 11:31 AM PST: I've filed a bug in launchpad: https://launchpad.net/ubuntu/+source/alsa-driver/+bug/888703

  Read the article

• Dual monitors, screen resolution, xorg.conf.d

  - by Flase

  I do a lot of RTFM but this one has got me stuck. I have Ubuntu Studio 12.04 Precise Pangolin with XFCE as its default desktop. My old HIS ATI Radeon 9250 graphics card was adding red crud across the screen with the generic driver, but downloading the proprietary "fglrx" driver makes it work cleanly. The trouble is the Catalyst control centre refuses to recognise my old card so I must do some manual configuring to make sure both the DVI and VGA monitors are capable of the correct screen resolution (both 1280x1024) and a dual display. It used to be easier to just edit the existing xorg.conf file and add another resolution and so forth, but now there are automatic xorg.conf.d directories (more than one) with scant documentation. Creating a generic xorg.conf with a terminal command creates every setting imaginable. What I want to do is create the simplest conf file which just tells the system the following: My VGA monitor can do 1280x1024 60Hz The two monitors together may be 2560x1024 width The VGA monitor on the right I might need to specify Xinerama if it's needed Thank you. I don't think I need to bore you with log files, but please ask for further info. Mike

  Read the article

• Disable discrete AMD GPU

  - by Smajl

  My notebook has two graphic cards and it suffers from severe overheating after installing Ubuntu (no problem with Windows 7 on the same machine). I figured out that the problem may be in the graphic card and I would like to disable the discrete one. I followed some tutorials on this topic (for example http://planetoss.com/articles/how-to-disable-the-discrete-amd-graphics-card-in-linux/). But the problem is, that after executing the commands, nothing really happens and both GPU are still running. Here is what I have done: smajl@smajl-mini:~$ sudo chown smajl /sys/kernel/debug/vgaswitcheroo/switchsmajl@smajl-mini:~$ echo IGD > /sys/kernel/debug/vgaswitcheroo/switch smajl@smajl-mini:~$ sudo cat /sys/kernel/debug/vgaswitcheroo/switch 0:IGD:+:DynPwr:0000:01:05.0 1:DIS-Audio: :Pwr:0000:02:00.1 2:DIS: :DynPwr:0000:02:00.0 smajl@smajl-mini:~$ echo OFF > /sys/kernel/debug/vgaswitcheroo/switch smajl@smajl-mini:~$ sudo cat /sys/kernel/debug/vgaswitcheroo/switch 0:IGD:+:DynPwr:0000:01:05.0 1:DIS-Audio: :Pwr:0000:02:00.1 2:DIS: :DynPwr:0000:02:00.0 What am I missing here? Also, more on the overheating topic: 1) Installed TLP 2) updated system 3) set power setting mode to "power save" ...and nothing helps Tried same thing with Linux Mint without success. Is there anything else to try if I manage to disable the second GPU and the problem preserves? Otherwise I would have to get back to win in order not to melt my laptop.. :-/

  Read the article

• dual monitors and unity - ati radeon cards

  - by michiel

  I have a vaio laptop with an ATI Radeon video card and an external screen. I used to run dual monitors on Ubuntu 10.10 fine, but recently decided to upgrade to 11.10 via 11.04 I don't think it's the video card or the fglrx driver. It seems to be unity. When I start up, the laptop screen is normal and the external screen is all white, although I can move my mouse over it. However, the cursor becomes the big X that used to be cursor of the first versions of Xwindows. I can right click on it, and it brings up the context menu for the desktop. And then, all of a sudden, it shows my desktop background. I can continue to move my mouse over the external screen, and now the cursor is normal (little white arrow). But I can't do anything any longer (not even the context menu as before), and trying to drag a window to it (which always worked on 10.10) doesn't work. I actually really like unity. It gives me the most our of my desktop, and uses all space available, which is great. But how can I get my second screen back? I tried unity 2D, but the result is the same. Edit: I think I stumbled on this bug: https://bugs.launchpad.net/ubuntu/+source/nvidia-settings/+bug/882143

  Read the article

• 12.04 disabling wireless via dbus does not work

  - by FlabbergastedPickle

  I am using a proprietary rt3652sta driver for my wireless card. It appears as a ra0 device on the 64-bit Ubuntu 12.04. According to the online documentation the following used to work definitely up to 10.04. dbus-send --system --type=method_call --dest=org.freedesktop.NetworkManager /org/freedesktop/NetworkManager org.freedesktop.DBus.Properties.Set string:org.freedesktop.NetworkManager string:WirelessEnabled variant:boolean:false This however has no effect on the aforesaid wireless card in 12.04. Also, rfkill does not work as it does not even list the wireless button (again, likely due to the wireless driver being proprietary): rfkill list It only lists the hci0 (bluetooth) one and one can block/unblock it accordingly but this has no effect on the wifi. ifup/down also does not work (AFAICT)... And this leaves me with disabling wireless through the network manager applet. However, trying to do so via dbus appears not to work and yet I would like to automate it via a script. Any ideas how I could find out the proper dbus structure for the call? Is this even possible in Ubuntu 12.04?

  Read the article

• Simple multi-seat

  - by Oli

  I've asked about multiseat before. The answer (for 10.04) involved doing it the proper way (eg through gdm, multiple server layouts). The problem was that gdm needs to be patched or reverted to 2.20 for multiseat. It's an ugly hack that, worse than anything, will hold up future updates. As a result, I didn't do anything. I still have a spare video card. I still have the monitor, keyboard and mouse all sitting waiting to jump into action. And I still want to be able to turn that into a simple desktop. My needs don't seem complicated. I have a second video card, a USB hub and anything connected to that USB hub that I want to be dedicated to another X server. I don't need a login screen (I'm happy hard-coding in a auto-login and I'd be happy with the user starting the X server if that's possible). This is so simple in my head that I only need two questions: How can I explicitly start an X server from the command line on an unused video adapter (by passing it whatever configuration I need to)? Can I have this new X session load a desktop environment on load? This seems like something you should be able to write in a little upstart script within 10 minutes. That would be perfect for me as then I'd have a nice start/stop control over the secondary desktop from the main desktop (that I want to leave unscathed!) I'm thinking something as simple as this for the payload: su -u other_user -c "startx -- localhost hardware-information" And use .xinitrc to load openbox or something...

  Read the article

• Ubuntu 12.04.1 LTS and Nvidia dirver (304.51) 64bit: problem 640x480

  - by nibianaswen

  I have a problem with this configuration: Asus K55V, Ubuntu 12.04 LTS and Nvidia driver 304.51. I have remove the nouveau driver with: apt-get --purge remove xserver-xorg-video-nouveau I installed the official nvidia driver (from www.nvidia.com) but when I reboot the PC the resolution of screen is only 640x480 and the monitor is resized. Mo solution at this problem if i change the xorg.conf. Now i have uninstall the nvidia driver and reinstall with sudo apt-get purge nvidia-current sudo apt-add-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get install nvidia-current When I reboot the screen resolution and size is OK, but if I start nvidia-setting I received the message: You do not appear to be using the NVIDIA X driver. and with command: sudo lshw -c display | grep driver I received configuration: driver=i915 latency=0 This sound like the system is using the Intel card. When I launch command lspci | grep VGA the output is: 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 1058 (rev ff) And there is no /etc/X11/xorg.conf. I have read a lot of guides on internet but without success.. How i can use nvidia card with the driver that i have installed?

  Read the article

• recent unreliable wireless connection with Netgear KWGR614 router

  - by gabkdlly

  Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I know that this router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. Is it possible that someone is jamming my signal ?

  Read the article

• Extension GLX missing...on a desktop PC

  - by Bart van Heukelom

  I just installed Ubuntu 12.10 on a new PC with an Nvidia GTX 560 graphics card, but after installing the Nvidia proprietary drivers (either -current or -current-updates), Unity won't start. When trying to start it manually I get the message "extension GLX missing". I've searched around and found results like this question which point out it's a problem with Nvidia Optimus laptops. However, I don't have this problem on a laptop, but on a desktop PC. lshw output for the graphics card: *-display description: VGA compatible controller product: GF114 [GeForce GTX 560 SE] vendor: NVIDIA Corporation physical id: 0 bus info: pci@0000:01:00.0 version: a1 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nouveau latency=0 resources: irq:16 memory:f4000000-f5ffffff memory:e0000000-e7ffffff memory:e8000000-ebffffff ioport:e000(size=128) memory:f6000000-f607ffff and CPU: *-cpu description: CPU product: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz vendor: Intel Corp. physical id: 40 bus info: cpu@0 version: Intel(R) Core(TM) i5-3570K CPU @ 3.40GHz slot: SOCKET 0 size: 1600MHz capacity: 3800MHz width: 64 bits clock: 100MHz capabilities: x86-64 fpu fpu_exception wp vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe syscall nx rdtscp constant_tsc arch_perfmon pebs bts rep_good nopl xtopology nonstop_tsc aperfmperf pni pclmulqdq dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm pcid sse4_1 sse4_2 popcnt tsc_deadline_timer aes xsave avx f16c rdrand lahf_lm ida arat epb xsaveopt pln pts dtherm tpr_shadow vnmi flexpriority ept vpid fsgsbase smep erms cpufreq configuration: cores=4 enabledcores=4 threads=4

  Read the article

• Multiple displays using AMD drivers

  - by Halik

  I am currently running a dual display setup with nVidia 8800GTS video card, on a Ubuntu 12.10 box. The current setup uses nVidia TwinView to render the image on a 1920x1200 display and 1600x1200 one. I'm planning to add a third, 1280x1024 display to the setup. The change will require me to upgrade my GFX card to one supporting triple displays. I'll probably go with Sapphire Radeon 7770 (FLEX edition, to avoid additional active DP-DVI adapters). Before I invest in new GFX I wanted to ask - how well the AMD drivers will support such a setup. It does not matter whether it's fglrx or the OSS ones. If I remember correctly, when running Fedora on a Radeon x800, I had 'void' areas above and below the working area on my second display. The desktop was rendered in 1920+1280 width and 1200 height (which left 176px of vertical space accessible for my cursor and windows but not displayed on the screen - I'd prefer to avoid that). It may have very well been my misconfiguration back then. Generally, are there any solutions from AMD on par with TwinView? Or is it a non-issue at all? Also, I'm wondering about the usual stuff - hardware h264 decoding support, glitch-free flash support, any issues with Compiz/Unity?

  Read the article

• How to keep background requests in sequence

  - by Jason Lewis

  I'm faced with implementing interfaces for some rather archaic systems, for handling online deposits to stored value accounts (think campus card accounts for students). Here's my dilemma: stage 1 of the process involves passing the user off to a thrid-party site for the credit card transaction, like old-school PayPal. Step two involves using a proprietary protocol for communicating with a legacy system for conducting the actual deposit. Step two requires that each transaction have a unique sequence number, and that the requests' seqnums are in order. Since we're logging each transaction in Postgres, my first thought was to take a number from a sequence in the DB, guaranteeing uniqueness. But since we're dealing with web requests that might come in near-simultaneously, and since latency with the return from the off-ste payment processor is beyond our control, there's always the chance for a race condition in the order of requests passed back to the proprietary system, and if the seqnums are out of order, the request fails silently (brilliant, right?). I thought about enqueuing the requests in Redis and using Resque workers to process them (single worker, single process, so they are processed in order), but we need to be able to give the user feedback as to whether the transaction was processed successfully, so this seems less feasible to me. I've tried to make this application handle concurrency well (as much as possible for a Ruby on Rails app), but now we're in a situation where we have to interact with a system that is designed to be single process, single threaded, and sequential. If it at least gave an "out of order" error, I could just increment (or take the next value off the sequence), but it's designed to fail silently in the event of ANY error. We are handling timeouts in a way that blocks on I/O, but since the application uses multiple workers (Unicorn), that's no guarantee. Any ideas/suggestions would be appreciated.

  Read the article

• Problems syncing photos and strange effects of uploaded files from other devices

  - by Daniel

  I have a Galaxy Spica (GT-i5700) Android v2.1, rooted with Leshak dev 7 #123. But never mind the root info, the problem would be the same unrooted. The photos from this phone is stored in "sdcard/images", nevertheless the phone also creates a "sdcard/DCIM" but only stores some thumbnails there. Problem nr 1: U1 only reads the DCIM-folder for automatic photo-upload. So photos stored in this phone is not uploaded. If I move photos to "DCIM" folder, U1 recognises the photos and start uploading them. Possible solution: Could there be an option in the settings, to set preferred photo folder? Problem nr 2: Out of 74 pictures, 12 did not get uploaded. Pressing "Retry failed transfers" in Settings does nothing. Pressing the files where status is "Upload failed, tap to retry" only changes the status to "Uploading..." but nothing gets uploaded. If I upload another file to U1, it is uploaded directly without any problem. It has nothing to do with file size, 1,1 MB files has been uploaded fine whilst some failed are 0,8 MB. Problem nr 3: The photos from DCIM are in my case uploaded to a folder called "Pictures - GT-I5700" in U1. If I log in to the homepage and from there upload another photo in "Pictures - GT-I5700", it shows up in U1 on my phone fine. But when I tap it, U1 downloads the photo to "sdcard/U1/Pictures - GT-I5700". If it sync photos from "sdcard/DCIM" to a specific folder, why not also download files to the same folder from which it is synced? After a while of usage, syncing and uploading files from different clients it would be a mishmash of folders and places files are stored and considering that I see no use of U1 at all. Another question: If my SD card in some way breaks down/some folders cannot be read/card temporarly changed and U1 is running, does U1 consider that as files deleted and also delete from the cloud?

  Read the article

• Ubuntu sound volume is 40% lower than in Windows

  - by ncomx

  I have 2x 2.1 speakers connected to the computer where I have Ubuntu 12.04 installed. On the software side I've set all the volume controls to 100% with the alsamixer program. The speakers have their own volume control, maintaining those at the same level, and switching between Ubuntu and Windows (XP and 7), on windows the output volume is at least 40% higher, even when having the windows volume control at 50% (without touching the speakers volume control) it's still much higher than the sound on Ubuntu. Why can this be happening? Are there some alternative sound drivers (other than the default ones) I could test to see if it makes a difference? some info about the card: root:$ cat /proc/asound/cards 0 [PCH ]: HDA-Intel - HDA Intel PCH HDA Intel PCH at 0xfbff4000 irq 55 1 [Generic ]: HDA-Intel - HD-Audio Generic HD-Audio Generic at 0xfbcfc000 irq 56 root:$ lspci | grep -i audio 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 02:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI Cayman/Antilles HDMI Audio [Radeon HD 6900 Series] I think the one i am using is the Intel one, the other seems to be from the vga card which is an ati radeon 6950. Running gstreamer-properties and switching between alsa, oss, ossv4 and pulseaudio doesn't seem to make any difference.

  Read the article

• recent unreliable wireless connection

  - by gabkdlly

  Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I have observed this problem with a Netgear KWGR614 Router ( with the manufacturers firmware ), as well as with a TP-LINK TL-WR741ND router running OpenWrt. Taking a look at my routers logs, I find many instances of the following line: Tuesday,04 Jan 2011 03:53:01 [TCP SYN Flood][Deny access policy matched, dropping packet] I know that the Netgear router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. I use WEP or WPA to encrypt the wireless network. Is it possible that someone is jamming my signal ?

  Read the article

• No monitor output after fresh install of 11.10 64-bit

  - by James

  I have a machine with a Nvidia 8600GT graphics card and a CRT monitor. Previously, I have only used Windows on it, and the graphics card seems to be working correctly in Windows 7. I booted up and installed Ubuntu 11.10 amd64 from the LiveCD and the whole process worked perfectly. When I tried to boot off the hard disk for the first time, the output to the monitor switched off during the splash screen, and this happens consistently. I can ctrl-alt-f2, so I tried an apt-get upgrade, which didn't help; nor did apt-get install nvidia-current. There is nothing that looks relevant in dmesg. Booting with the nomodeset option has no effect. Following the answers in this similar thread, I tried apt-get purge nvidia-173. Both startx and service lightdm start just say the service is already running. Does anyone know how to find out what the problem is? I was wondering if it is just that Ubuntu is trying to use a resolution that the monitor doesn't support, but I can't find out how to change that from the command line.

  Read the article

• Laptop Display Not Working

  - by etrask

  Hello, I just purchased this laptop. It is working fine but I want to use Xubuntu on it. I managed to get 10.04 installed and running but it did not recognize/use the wireless card. So I want to try 10.10. However, every time I try, the screen goes black and never comes back on. I have tried the Live CD and Alternate install CDs, for both Ubuntu and Xubuntu 10.10. After I select "Install Ubuntu" or "Try Ubuntu", the screen blacks out and never displays anything. So I deleted "quiet" and "splash" off the command line to see what messages would come up. A bunch of text flies by but it ends at: [time] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [time] TCP bind hash table entries 65536 (order: 8, 1048576 bytes) [time] TCP: Hash tables configured (established 524288 bind 65536) [time] TCP reno registered [time] UDP hash table entries: 2048 (order: 4, 65536 bytes) [time] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [time] NET: Registered protocol family 1 And freezes here forever. I have tried nomodeset, vga=771, and xforcevesa with no progress. Is my video card simply not going to work with this distro? It seems strange that 10.04 would work fine but not 10.10. Any help is appreciated, thank you.

  Read the article

• Can't install the wireless driver in HP Pavilion dv2419us

  - by maqtanim

  I've just installed Ubuntu 13.04 in an old HP Pavilion dv2419us. The problem is, Ubuntu doesn't detect the wireless card. But it works fine in Windows 7. The following command returns nothing! lspci -vvnn | grep 14e4 And the lspci output is: 00:00.1 RAM memory: NVIDIA Corporation C51 Memory Controller 0 (rev a2) 00:00.2 RAM memory: NVIDIA Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: NVIDIA Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: NVIDIA Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: NVIDIA Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: NVIDIA Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: NVIDIA Corporation C51 Memory Controller 2 (rev a2) 00:02.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:03.0 PCI bridge: NVIDIA Corporation C51 PCI Express Bridge (rev a1) 00:05.0 VGA compatible controller: NVIDIA Corporation C51 [GeForce Go 6150] (rev a2) 00:09.0 RAM memory: NVIDIA Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: NVIDIA Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: NVIDIA Corporation MCP51 SMBus (rev a3) 00:0a.3 Co-processor: NVIDIA Corporation MCP51 PMU (rev a3) 00:0b.0 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB controller: NVIDIA Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: NVIDIA Corporation MCP51 IDE (rev f1) 00:0e.0 IDE interface: NVIDIA Corporation MCP51 Serial ATA Controller (rev f1) 00:10.0 PCI bridge: NVIDIA Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: NVIDIA Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: NVIDIA Corporation MCP51 Ethernet Controller (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 05:09.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller 05:09.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 19) 05:09.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 0a) 05:09.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 05) The command lspci -nn | grep 0280 gives no output. Any suggestion regarding this?

  Read the article

• Error loading libGL.so.1

  - by jdp407

  When attempting to run various pieces of software (notably Steam and Yenka), I have come across an error similar to this: enter code here error while loading shared libraries: libGL.so.1: cannot open shared object file: No such file or directory I'm running a 64 bit system, with an NVidia Optimus card (I dual boot for certain windows only software that requires a dedicated graphics card). I have bumblebee installed, and I am using the nvidia-current driver, rather that one downloaded from NVidia, as recommended. The library (libGL.so.1) is not present in the top directory of /usr/lib, however it is present in /usr/lib32/nvidia-current, as a softlink to /usr/lib32/nvidia-current/libGL.so.304.64. A section of the output from ldconfig -p: libGL.so.1 (libc6,x86-64, OS ABI: Linux 2.4.20) => /usr/lib/x86_64-linux-gnu/mesa/libGL.so.1 libGL.so (libc6,x86-64, OS ABI: Linux 2.4.20) => /usr/lib/x86_64-linux-gnu/libGL.so libGL.so (libc6,x86-64, OS ABI: Linux 2.4.20) => /usr/lib/x86_64-linux-gnu/mesa/libGL.so Obviously a library with that name is being loaded, but they are located in /usr/lib/x86_64-linux-gnu, however installed software doesn't seem to able to 'see' it. For Steam, running it with optirun causes it to work, but this is not the case for Yenka. I assume that optirun causes the library stored in /usr/lib32/nvidia-current to be used, which allows Steam to run, so I can't understant why Yenka won't run. Can anyone explain why software can't see the normal mesa library, and why Yenka refuses to run with the nvidia-current library?

  Read the article

• can't get a good install:11.10 server

  - by jack

  I screwed up my partitioning aparently tring to get lvm and raid1 going. the machine is an intel dual core dt with 2 gig of ram and 2 sata drives, one 250g and the other 500g. This a build for my school in n.e. Thailand. we have 20+ clients now, a website, email. Our old server is dying fast and we are going to add another 12 stations next week. I really need some help here! 1. have onboard gigabit ethernet that aparently uses same driver as realtek 811c. I installed a pcie gigabit card also 811c. At several points the eth0 has accessed the internet fine, but the eth1 will not communicate. 2. I saw a "fix" for this online which from root: rmmod r8169. this imediately killed the working onboard card. 3.I tried to re-install 11.10 figuring that would re-install r8169. However I messed something up in my partitioning and can't get a clean boot now. 6. so I think after 12 re-installs or so and 2 days. I can get through it right if I can start over with clean drives, but I can't figure out how to empty them out what with soft raid and lvm partitions. seems like i've had it going well and then trying to fix that one little problem, i go backwards.Please help! please send email.-thanks

  Read the article

< Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >