Search Results

Search found 2871 results on 115 pages for 'f2 cmd'.

Page 97/115 | < Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >

  • SATA drives or chipset throwing DRDY ERR and ICRC ABRT

    - by Matt
    I have an SD-VIA-1A2S PCI card with 2 sata ports (and one ATA-133 that isn't used). Two new Western Digital Caviar Green drives (WD10EARS 1TB) throw repeated errors in kern.log (removed date/time/host info for brevity): [ 7.376475] ata2.00: exception Emask 0x12 SAct 0x0 SErr 0x1000500 action 0x6 [ 7.376480] ata2.00: BMDMA stat 0x5 [ 7.376483] ata2: SError: { UnrecovData Proto TrStaTrns } [ 7.376489] ata2.00: cmd c8/00:40:20:00:00/00:00:00:00:00/e0 tag 0 dma 32768 in [ 7.376490] res 51/84:2f:20:00:00/00:00:00:00:00/e0 Emask 0x12 (ATA bus error) [ 7.376493] ata2.00: status: { DRDY ERR } [ 7.376495] ata2.00: error: { ICRC ABRT } [ 7.376504] ata2: hard resetting link I'm using Ubuntu 9.04 - 2.6.28-18-generic, though I have tried live cds of Ubuntu 9.10, Fedora 12 and OpenSUSE 11.2 - all running various 2.6.31 kernels - and all received the same error. Based on testing these drives and this card in two other machines and combos of connecting the drives directly to the motherboard or the add-in card, I'm relatively convinced that it's the VIA chipset that is the problem. Another computer that also has an onboard VIA SATA chipset (like the add-in card) produces the same errors when the drives are directly on that motherboard. I have been able to verify that the drives are perfectly good, and I tried everything I can think of in terms of swapping cables, psu isn't overloaded, etc. The error happens on boot once or twice, after using fdisk on the drive once or twice, and constantly when attempting to sync a new mdadm raid 1 array created on the two drives. Any thoughts on where to go from here - driver/kernel wise? I'm completely open to buying a new PCI add-in card if someone can recommend one with 2 internal sata ports that works well in Debian/Ubuntu. Thanks!

    Read the article

  • NGINX MIME TYPE

    - by justanotherprogrammer
    I have my nginx conf file so that when ever a mobile device visits my site the url gets rewritten to m.mysite.com I did it by adding the following set $mobile_rewrite do_not_perform; if ($http_user_agent ~* "android.+mobile|avantgo|bada\/|blackberry|blazer|compal|elaine|fennec|hiptop|iemobile|ip(hone|od)|iris|kindle|lge |maemo|midp|mmp|netfront|opera m(ob|in)i|palm( os)?|phone|p(ixi|re)\/|plucker|pocket|psp|symbian|treo|up\.(browser|link)|vodafone|wap|windows (ce|phone)|xda|xiino") { set $mobile_rewrite perform; } if ($http_user_agent ~* "^(1207|6310|6590|3gso|4thp|50[1-6]i|770s|802s|a wa|abac|ac(er|oo|s\-)|ai(ko|rn)|al(av|ca|co)|amoi|an(ex|ny|yw)|aptu|ar(ch|go)|as(te|us)|attw|au(di|\-m|r |s )|avan|be(ck|ll|nq)|bi(lb|rd)|bl(ac|az)|br(e|v)w|bumb|bw\-(n|u)|c55\/|capi|ccwa|cdm\-|cell|chtm|cldc|cmd\-|co(mp|nd)|craw|da(it|ll|ng)|dbte|dc\-s|devi|dica|dmob|do(c|p)o|ds(12|\-d)|el(49|ai)|em(l2|ul)|er(ic|k0)|esl8|ez([4-7]0|os|wa|ze)|fetc|fly(\-|_)|g1 u|g560|gene|gf\-5|g\-mo|go(\.w|od)|gr(ad|un)|haie|hcit|hd\-(m|p|t)|hei\-|hi(pt|ta)|hp( i|ip)|hs\-c|ht(c(\-| |_|a|g|p|s|t)|tp)|hu(aw|tc)|i\-(20|go|ma)|i230|iac( |\-|\/)|ibro|idea|ig01|ikom|im1k|inno|ipaq|iris|ja(t|v)a|jbro|jemu|jigs|kddi|keji|kgt( |\/)|klon|kpt |kwc\-|kyo(c|k)|le(no|xi)|lg( g|\/(k|l|u)|50|54|e\-|e\/|\-[a-w])|libw|lynx|m1\-w|m3ga|m50\/|ma(te|ui|xo)|mc(01|21|ca)|m\-cr|me(di|rc|ri)|mi(o8|oa|ts)|mmef|mo(01|02|bi|de|do|t(\-| |o|v)|zz)|mt(50|p1|v )|mwbp|mywa|n10[0-2]|n20[2-3]|n30(0|2)|n50(0|2|5)|n7(0(0|1)|10)|ne((c|m)\-|on|tf|wf|wg|wt)|nok(6|i)|nzph|o2im|op(ti|wv)|oran|owg1|p800|pan(a|d|t)|pdxg|pg(13|\-([1-8]|c))|phil|pire|pl(ay|uc)|pn\-2|po(ck|rt|se)|prox|psio|pt\-g|qa\-a|qc(07|12|21|32|60|\-[2-7]|i\-)|qtek|r380|r600|raks|rim9|ro(ve|zo)|s55\/|sa(ge|ma|mm|ms|ny|va)|sc(01|h\-|oo|p\-)|sdk\/|se(c(\-|0|1)|47|mc|nd|ri)|sgh\-|shar|sie(\-|m)|sk\-0|sl(45|id)|sm(al|ar|b3|it|t5)|so(ft|ny)|sp(01|h\-|v\-|v )|sy(01|mb)|t2(18|50)|t6(00|10|18)|ta(gt|lk)|tcl\-|tdg\-|tel(i|m)|tim\-|t\-mo|to(pl|sh)|ts(70|m\-|m3|m5)|tx\-9|up(\.b|g1|si)|utst|v400|v750|veri|vi(rg|te)|vk(40|5[0-3]|\-v)|vm40|voda|vulc|vx(52|53|60|61|70|80|81|83|85|98)|w3c(\-| )|webc|whit|wi(g |nc|nw)|wmlb|wonu|x700|xda(\-|2|g)|yas\-|your|zeto|zte\-)") { set $mobile_rewrite perform; } if ($mobile_rewrite = perform) { rewrite ^ http://m.mywebsite.com redirect; break; } I got it from http://detectmobilebrowsers.com/ IT WORKS.But none of my images/js/css files load only the HTML. And I know its the chunk of code I mentioned above because when I remove it and visit m.mywebsite.com from my mobile device everything loads up.So this bit of code does SOMETHING to my css/img/js MIME TYPES. I found this out through the the console error messages from safari with the user agent set to iphone. text.cssResource interpreted as stylesheet but transferred with MIME type text/html. 960_16_col.cssResource interpreted as stylesheet but transferred with MIME type text/html. design.cssResource interpreted as stylesheet but transferred with MIME type text/html. navigation_menu.cssResource interpreted as stylesheet but transferred with MIME type text/html. reset.cssResource interpreted as stylesheet but transferred with MIME type text/html. slide_down_panel.cssResource interpreted as stylesheet but transferred with MIME type text/html. myrealtorpage_view.cssResource interpreted as stylesheet but transferred with MIME type text/html. head.jsResource interpreted as script but transferred with MIME type text/html. head.js:1SyntaxError: Parse error isaac:208ReferenceError: Can't find variable: head mrp_home_icon.pngResource interpreted as image but transferred with MIME type text/html. M_1_L_289_I_499_default_thumb.jpgResource interpreted as image but transferred with MIME type text/html. M_1_L_290_I_500_default_thumb.jpgResource interpreted as image but transferred with MIME type text/html. M_1_default.jpgResource interpreted as image but transferred with MIME type text/html. default_listing_image.pngResource interpreted as image but transferred with MIME type text/html. here is my whole nginx conf file just incase... worker_processes 1; events { worker_connections 1024; } http { include mime.types; include /etc/nginx/conf/fastcgi.conf; default_type application/octet-stream; sendfile on; keepalive_timeout 65; #server1 server { listen 80; server_name mywebsite.com www.mywebsite.com ; index index.html index.htm index.php; root /srv/http/mywebsite.com/public; access_log /srv/http/mywebsite.com/logs/access.log; error_log /srv/http/mywebsite.com/logs/error.log; #---------------- For CodeIgniter ----------------# # canonicalize codeigniter url end points # if your default controller is something other than "welcome" you should change the following if ($request_uri ~* ^(/main(/index)?|/index(.php)?)/?$) { rewrite ^(.*)$ / permanent; } # removes trailing "index" from all controllers if ($request_uri ~* index/?$) { rewrite ^/(.*)/index/?$ /$1 permanent; } # removes trailing slashes (prevents SEO duplicate content issues) if (!-d $request_filename) { rewrite ^/(.+)/$ /$1 permanent; } # unless the request is for a valid file (image, js, css, etc.), send to bootstrap if (!-e $request_filename) { rewrite ^/(.*)$ /index.php?/$1 last; break; } #---------------------------------------------------# #--------------- For Mobile Devices ----------------# set $mobile_rewrite do_not_perform; if ($http_user_agent ~* "android.+mobile|avantgo|bada\/|blackberry|blazer|compal|elaine|fennec|hiptop|iemobile|ip(hone|od)|iris|kindle|lge |maemo|midp|mmp|netfront|opera m(ob|in)i|palm( os)?|phone|p(ixi|re)\/|plucker|pocket|psp|symbian|treo|up\.(browser|link)|vodafone|wap|windows (ce|phone)|xda|xiino") { set $mobile_rewrite perform; } if ($http_user_agent ~* "^(1207|6310|6590|3gso|4thp|50[1-6]i|770s|802s|a wa|abac|ac(er|oo|s\-)|ai(ko|rn)|al(av|ca|co)|amoi|an(ex|ny|yw)|aptu|ar(ch|go)|as(te|us)|attw|au(di|\-m|r |s )|avan|be(ck|ll|nq)|bi(lb|rd)|bl(ac|az)|br(e|v)w|bumb|bw\-(n|u)|c55\/|capi|ccwa|cdm\-|cell|chtm|cldc|cmd\-|co(mp|nd)|craw|da(it|ll|ng)|dbte|dc\-s|devi|dica|dmob|do(c|p)o|ds(12|\-d)|el(49|ai)|em(l2|ul)|er(ic|k0)|esl8|ez([4-7]0|os|wa|ze)|fetc|fly(\-|_)|g1 u|g560|gene|gf\-5|g\-mo|go(\.w|od)|gr(ad|un)|haie|hcit|hd\-(m|p|t)|hei\-|hi(pt|ta)|hp( i|ip)|hs\-c|ht(c(\-| |_|a|g|p|s|t)|tp)|hu(aw|tc)|i\-(20|go|ma)|i230|iac( |\-|\/)|ibro|idea|ig01|ikom|im1k|inno|ipaq|iris|ja(t|v)a|jbro|jemu|jigs|kddi|keji|kgt( |\/)|klon|kpt |kwc\-|kyo(c|k)|le(no|xi)|lg( g|\/(k|l|u)|50|54|e\-|e\/|\-[a-w])|libw|lynx|m1\-w|m3ga|m50\/|ma(te|ui|xo)|mc(01|21|ca)|m\-cr|me(di|rc|ri)|mi(o8|oa|ts)|mmef|mo(01|02|bi|de|do|t(\-| |o|v)|zz)|mt(50|p1|v )|mwbp|mywa|n10[0-2]|n20[2-3]|n30(0|2)|n50(0|2|5)|n7(0(0|1)|10)|ne((c|m)\-|on|tf|wf|wg|wt)|nok(6|i)|nzph|o2im|op(ti|wv)|oran|owg1|p800|pan(a|d|t)|pdxg|pg(13|\-([1-8]|c))|phil|pire|pl(ay|uc)|pn\-2|po(ck|rt|se)|prox|psio|pt\-g|qa\-a|qc(07|12|21|32|60|\-[2-7]|i\-)|qtek|r380|r600|raks|rim9|ro(ve|zo)|s55\/|sa(ge|ma|mm|ms|ny|va)|sc(01|h\-|oo|p\-)|sdk\/|se(c(\-|0|1)|47|mc|nd|ri)|sgh\-|shar|sie(\-|m)|sk\-0|sl(45|id)|sm(al|ar|b3|it|t5)|so(ft|ny)|sp(01|h\-|v\-|v )|sy(01|mb)|t2(18|50)|t6(00|10|18)|ta(gt|lk)|tcl\-|tdg\-|tel(i|m)|tim\-|t\-mo|to(pl|sh)|ts(70|m\-|m3|m5)|tx\-9|up(\.b|g1|si)|utst|v400|v750|veri|vi(rg|te)|vk(40|5[0-3]|\-v)|vm40|voda|vulc|vx(52|53|60|61|70|80|81|83|85|98)|w3c(\-| )|webc|whit|wi(g |nc|nw)|wmlb|wonu|x700|xda(\-|2|g)|yas\-|your|zeto|zte\-)") { set $mobile_rewrite perform; } if ($mobile_rewrite = perform) { rewrite ^ http://m.mywebsite.com redirect; #rewrite ^(.*)$ $scheme://mywebsite.com/mobile/$1; #return 301 http://m.mywebsite.com; #break; } #---------------------------------------------------# location / { index index.html index.htm index.php; } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } location ~ \.php$ { try_files $uri =404; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; include /etc/nginx/conf/fastcgi_params; } }#sever1 #server 2 server { listen 80; server_name m.mywebsite.com; index index.html index.htm index.php; root /srv/http/mywebsite.com/public; access_log /srv/http/mywebsite.com/logs/access.log; error_log /srv/http/mywebsite.com/logs/error.log; #---------------- For CodeIgniter ----------------# # canonicalize codeigniter url end points # if your default controller is something other than "welcome" you should change the following if ($request_uri ~* ^(/main(/index)?|/index(.php)?)/?$) { rewrite ^(.*)$ / permanent; } # removes trailing "index" from all controllers if ($request_uri ~* index/?$) { rewrite ^/(.*)/index/?$ /$1 permanent; } # removes trailing slashes (prevents SEO duplicate content issues) if (!-d $request_filename) { rewrite ^/(.+)/$ /$1 permanent; } # unless the request is for a valid file (image, js, css, etc.), send to bootstrap if (!-e $request_filename) { rewrite ^/(.*)$ /index.php?/$1 last; break; } #---------------------------------------------------# location / { index index.html index.htm index.php; } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } location ~ \.php$ { try_files $uri =404; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; include /etc/nginx/conf/fastcgi_params; } }#sever2 }#http I could just detect the mobile browsers with php or javascript but i need to make the detection at the server level so that i can use the 'm' in m.mywebsite.com as a flag in my controllers (codeigniter) to serve up the right view. I hope someone can help me! Thank you!

    Read the article

  • Can't setup 3 nodes MongoDB recplica set

    - by Victor Lin
    I just follow instructions in MongoDB document Replica Sets - Basics to setup a 3-node Replica set. Everything goes fine when I do the initiate and add first node in the primary. [foo@host-a mongodb]$ bin/mongo localhost MongoDB shell version: 1.8.2 connecting to: localhost > rs.initiate() { "info2" : "no configuration explicitly specified -- making one", "info" : "Config now saved locally. Should come online in about a minute.", "ok" : 1 } > rs.add("host-b") { "ok" : 1 } So far so good, but when I try to add third node myset:PRIMARY> rs.addArb("host-c") Sun Aug 7 22:57:09 MessagingPort recv() errno:104 Connection reset by peer 127.0.0.1:27017 Sun Aug 7 22:57:09 SocketException: remote: error: 9001 socket exception [1] Sun Aug 7 22:57:09 DBClientCursor::init call() failed Sun Aug 7 22:57:09 query failed : local.$cmd { count: "system.replset", query: {}, fields: {} } to: 127.0.0.1 Sun Aug 7 22:57:09 Error: error doing query: failed shell/collection.js:150 Sun Aug 7 22:57:09 trying reconnect to 127.0.0.1 Sun Aug 7 22:57:09 reconnect 127.0.0.1 ok As result, the current primary became secondary, and the host-b was marked as dead, but actually, it is still alive. myset:SECONDARY> rs.status() { "set" : "myset", "date" : ISODate("2011-08-08T04:03:23Z"), "myState" : 2, "members" : [ { "_id" : 0, "name" : "host-a:27017", "health" : 1, "state" : 2, "stateStr" : "SECONDARY", "optime" : { "t" : 1312775799000, "i" : 1 }, "optimeDate" : ISODate("2011-08-08T03:56:39Z"), "self" : true }, { "_id" : 1, "name" : "host-b", "health" : 0, "state" : 6, "stateStr" : "(not reachable/healthy)", "uptime" : 0, "optime" : { "t" : 0, "i" : 0 }, "optimeDate" : ISODate("1970-01-01T00:00:00Z"), "lastHeartbeat" : ISODate("2011-08-08T04:03:22Z"), "errmsg" : "still initializing" } ], "ok" : 1 } How could this happen? I just follow the guide in the document, did I do something wrong? Moreover, I can't do anything on current secondary server. It doesn't allow me to reconfig on the secondary node, but the problem is there is no primary node. myset:SECONDARY> rs.reconfig({}) { "errmsg" : "replSetReconfig command must be sent to the current replica set primary.", "ok" : 0 } Any ideas?

    Read the article

  • How to Increase the VMWare Boot Screen Delay

    - by Trevor Bekolay
    If you’ve wanted to try out a bootable CD or USB flash drive in a virtual machine environment, you’ve probably noticed that VMWare’s offerings make it difficult to change the boot device. We’ll show you how to change these options. You can do this either for one boot, or permanently for a particular virtual machine. Even experienced users of VMWare Player or Workstation may not recognize the screen above – it’s the virtual machine’s BIOS, which in most cases flashes by in the blink of an eye. If you want to boot up the virtual machine with a CD or USB key instead of the hard drive, then you’ll need more than an eye’s-blink to press Escape and bring up the Boot Menu. Fortunately, there is a way to introduce a boot delay that isn’t exposed in VMWare’s graphical interface – you have to edit the virtual machine’s settings file (a .vmx file) manually. Editing the Virtual Machine’s .vmx Find the .vmx file that contains the settings for your virtual machine. You chose a location for this when you created the virtual machine – in Windows, the default location is a folder called My Virtual Machines in your My Documents folder. In VMWare Workstation, the location of the .vmx file is listed on the virtual machine’s tab. If in doubt, search your hard drive for .vmx files. If you don’t want to use Windows default search, an awesome utility that locates files instantly is Everything. Open the .vmx file with any text editor. Somewhere in this file, enter in the following line… save the file, then close out of the text editor: bios.bootdelay = 20000 This will introduce a 20 second delay when the virtual machine loads up, giving you plenty of time to press the Escape button and access the boot menu. The number in this line is just a value in milliseconds, so for a five second boot delay, enter 5000, and so on. Change Boot Options Temporarily Now, when you boot up your virtual machine, you’ll have plenty of time to enter one of the keystrokes listed at the bottom of the BIOS screen on boot-up. Press Escape to bring up the Boot Menu. This allows you to select a different device to boot from – like a CD drive. Your selection will be forgotten the next time you boot up this virtual machine. Change Boot Options Permanently When the BIOS screen comes up, press F2 to enter the BIOS Setup menu. Switch to the Boot tab, and change the ordering of the items by pressing the “+” key to move items up on the list, and the “-” key to move items down the list. We’ve switched the order so that the CD-ROM Drive boots first. Once you make this change permanent, you may want to re-edit the .vmx file to remove the boot delay. Boot from a USB Flash Drive One thing that is noticeably missing from the list of boot options is a USB device. VMWare’s BIOS just does not allow this, but we can get around that limitation using the PLoP Boot Manager that we’ve previously written about. And as a bonus, since everything is virtual anyway, there’s no need to actually burn PLoP to a CD. Open the settings for the virtual machine you want to boot with a USB drive. Click on Add… at the bottom of the settings screen, and select CD/DVD Drive. Click Next. Click the Use ISO Image radio button, and click Next. Browse to find plpbt.iso or plpbtnoemul.iso from the PLoP zip file. Ensure that Connect at power on is checked, and then click Finish. Click OK on the main Virtual Machine Settings page. Now, if you use the steps above to boot using that CD/DVD drive, PLoP will load, allowing you to boot from a USB drive! Conclusion We’re big fans of VMWare Player and Workstation, as they let us try out a ton of geeky things without worrying about harming our systems. By introducing a boot delay, we can add bootable CDs and USB drives to the list of geeky things we can try out. Download PLoP Boot Manager Similar Articles Productive Geek Tips How To Switch to Console Mode for Ubuntu VMware GuestHack: Turn Off Debug Mode in VMWare Workstation 6 BetaStart Your Computer More Quickly by Delaying the Startup of a Service in VistaEnable Hidden BootScreen in Windows VistaEnable Copy and Paste from Ubuntu VMware Guest TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 OutlookStatView Scans and Displays General Usage Statistics How to Add Exceptions to the Windows Firewall Office 2010 reviewed in depth by Ed Bott FoxClocks adds World Times in your Statusbar (Firefox) Have Fun Editing Photo Editing with Citrify Outlook Connector Upgrade Error

    Read the article

  • Nagios plug-in check_snmp receives NO SNMP data from a CISCO Router

    - by Shehryar
    I have tried setting up Nagios on Ubuntu 10.10, successfully installed and can login to web interface, I am however stuck on configuring snmp or I am doing something wrong here, i have followed various sites / nagios wiki to setup configuration (cfg) files. When I check on the web interface, it gives the following error on one of my cisco router: Current Status: UNKNOWN (for 0d 2h 55m 56s) Status Information: SNMP problem - No data received from host CMD: /usr/bin/snmpget -t 1 -r 5 -m RFC1213-MIB -v 1 [authpriv] 192.168.1.1:161 ifOperStatus.1 On the command-line itself, when I type the following, it just sits there waiting and waiting : sudo /usr/local/nagios/libexec/check_snmp -H 192.168.1.1 -C Routers -o sysUpTime.0 When I type the following command : I get an OK /usr/bin/snmpget -v1 192.168.1.1:161 1.3.6.1.2.1.1.5.0 -c "Routers" I have configured SNMP properly on our cisco device as we can collect SNMP Data via two other monitoring tool (SolarWinds and Manage Engine), we are tempted towards Nagios as its opensource. Will be grateful if someone could assist in rectifying this situation and guide me with setting up nagios to monitor Cisco Routers, Switches and a Few Servers. We want to monitor Bandwidth, cpu utilization, uptime and other necessary counters. Will be grateful for your assistance Thanks for reading Shehryar

    Read the article

  • Drop database on DB2 9.5 - SQL1035N The database is currently in use

    - by Tommy
    I've never got this working the first time, but now I can't seem to do i at all. There is a connection pool somewhere using the database, so trying to drop the database when an application is using the database should give this error. The problem is there are no connection to the database when I issue these commands: db2 connect to mydatabase db2 quiesce database immediate force connections db2 connect reset db2 drop database mydatabase This allways give: SQL1035N The database is currently in use. SQLSTATE=57019 running this command shows no connections/applications DB2 list applications I can even deactivate the database, but still can't drop it. db2 => deactivate database mydatabase DB20000I The DEACTIVATE DATABASE command completed successfully. db2 => drop database mydatabase SQL1035N The database is currently in use. SQLSTATE=57019 db2 => Anyone got any clues? I'm running the cmd-windows as the local administrator (windows 2008) and this is also the admin for DB2. The connectionpool-user cannot connect during quiesce-state.

    Read the article

  • Mystery undeletable file

    - by Hugh Allen
    I can't delete C:\Config.Msi\75ce84f.rbf. it's not readonly, system or hidden it's not in use by another process (according to Process Explorer) the NT security permissions aren't the problem either - I am the owner and have Full Control ; as a double-check, the Effective Permissions tab shows that I have permission to delete. Yet trying to delete the file gives "Access is Denied" from both Explorer and cmd. I can however rename it or move it to another folder on the same drive. I can also read it and Virustotal says it's clean which is what I would expect (it's just a Windows Installer temp file - a copy of some DLL I think). The relevant line from Process Monitor is: 6:52:14.3726983 PM 112 Explorer.EXE SetDispositionInformationFile C:\Config.Msi\75ce84f.rbf CANNOT DELETE Delete: True Write 1232 Background: I'm using XP SP2. I recently repaired my Adobe Reader installation to make it the default browser plugin again instead of Foxit. (there seems to be no UI to do it otherwise?) So the installer did its thing and then asked to reboot. As is my habit when rebooting is inconvenient I declined the offer and ran pendmoves to find out what files the installer had scheduled to move / delete. It wanted to delete two files with .rbf extension (rollback files) located in C:\Config.msi\. (this applies to both even though I've been speaking about one). So I tried to delete them manually and couldn't. Does anyone have any ideas what could be preventing deletion? (and I don't think it's malware even though I'm not running AV at the moment)

    Read the article

  • Not Able To Connect to Windows Server 2008 R2 using FileZilla Externally

    - by obautista
    I configured FTP Service/Role on my Windows Server 2008 R2 machine. I am able to connect from the inside, but not from the outside. On the inside I tested using cmd prompt and IE FTP. On the outside, I am testing with FileZilla and IE FTP. From the outside, IE FTP prompts me to enter my username/pwd, but nothing happens. Page eventually times out and I get "Internet Explorer cannot display page". Using FileZilla, I get the following messages. Note FileZilla resolved domain name and authenticates. I did not configure FTP Wirewall Support on the FTP site. I am not sure if I need to do this. I set up basic authentication, non-ssl, not allowing anonymous. I testing with Windows Firewall Turned off and on (I added windows firewall rule for port 21). On my network firewall (Cisco), I added a rule to forward port 21 traffic to FTP Server. Status: Resolving address of ftp.technologyblends.com Status: Connecting to 75.149.66.201:21... Status: Connection established, waiting for welcome message... Response: 220 Microsoft FTP Service Command: USER * Response: 331 Password required for . Command: PASS *** Response: 230 User logged in. Command: SYST Response: 215 Windows_NT Command: FEAT Response: 211-Extended features supported: Response: LANG EN* Response: UTF8 Response: AUTH TLS;TLS-C;SSL;TLS-P; Response: PBSZ Response: PROT C;P; Response: CCC Response: HOST Response: SIZE Response: MDTM Response: REST STREAM Response: 211 END Command: OPTS UTF8 ON Response: 200 OPTS UTF8 command successful - UTF8 encoding now ON. Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is current directory. Command: TYPE I Response: 200 Type set to I. Command: PASV Error: Connection timed out Error: Failed to retrieve directory listing

    Read the article

  • Broken UAC, cant edit File/folders or change settings in user account

    - by Antoros
    It appears that UAC is broken cant move/delete some file/folders, when asked to use administrative right (and say yes) it shows the loading bar and then nothings gets moved/deleted, no error whatsoever opened control panel, user account and when i click on any option with the Shield (administrative rights) the mouse changes to loading and thengo back to normal, not opening any menu or showing any error Already done a sfc /scannow , no errors found Already used Microsoft's Fix it, reclycle bin broken and repaired, still the same error Used microsoftaccounts tool , this are the errors i got: Problem with microsoft account policy... <- this is the problem (didint fix) Trust this PC <- loop of redirections, cant get to trust this pc (only one with w8) Problems witht sytem registration : i think it is because of the soft system reset Some setting have sync turned off : i never configured anything to sync Rootcauses found and created logs : would like to know where the logs are saved... had to use a ".reg" file to change uac setting to never notify, thinking it would fix this, no, it stoped asking though, i can still open a cmd with Administrative rights, but cant access to UAC settings Accesed Administrator account (net user administrator /active:yes)and even with that account could change any settings so there it is, dont know what else to do in the moment (this pc broke with 8.1 update and was restored to factory configuration, it broke several drivers and kept most of the registry entries, i cant find the cause of this problem. other info: i tried to delete a file in a program folder and couldnt, downloaded unlocker to check first if it was permissions but no, it showed me a msg telling me that there wasnt any error, and if i would like to delete it, clicked on yes, and it did delete it, what amuses me is that i cant without this tool, not even using the feature that takes over ownership Edit: wow, in a not crappy pc chkdsk is fast, completed with no errors found : /

    Read the article

  • ESXI 5.1 - Unable to trunk to cisco switch

    - by Lance
    I have configured my esxi host vSwitch1 to use the secondary NIC on my VMware host. On vSwitch1 configuration I have set the VLAN to 4095 which specifies to allow all VLANs. If my cisco switch port configuration is set to an access port my server can ping the vlan interface on the switch. If my cisco switch port configuration is set to a trunk, whilst it stays UP UP and CDP information is available, I lose my ping from VMware VM server to the local vlan interface on the switch and I lose any server connectivity to my network. Switch NIC teaming policy to Route based on originating virtual port ID Configuration based on: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1006628 interface GigabitEthernet0/42 description Host Port switchport trunk encapsulation dot1q switchport trunk allowed vlan 18,220 switchport mode trunk switchport nonegotiate spanning-tree portfast trunk end Output from ESXI CLI esxcfg-vswitch -l: ~ # esxcfg-vswitch -l Switch Name Num Ports Used Ports Configured Ports MTU Uplinks vSwitch0 128 5 128 1500 vmnic0 PortGroup Name VLAN ID Used Ports Uplinks VM Network 4095 1 vmnic0 Management Network 4095 1 vmnic0 Switch Name Num Ports Used Ports Configured Ports MTU Uplinks vSwitch1 128 4 128 1500 vmnic1 PortGroup Name VLAN ID Used Ports Uplinks VM Network 2 4095 1 vmnic1 Any tips welcome!!!

    Read the article

  • Linux error when resume from RAM

    - by TuxPotato
    The last two times that I have resumed my laptop from sleep, it has hung and given me this set of errors: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 hda_intel: azx_get_responce timeout, switching to single_cmd mode: last cmd=0x01170700 ata6: softreset failed (device not ready) ata4: softreset failed (device not ready) [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 The last two messages repeat two more times. The first time this happened, Linux's Magic SysRq worked and did a soft reboot, and after that everything was fine till it went to sleep again. It wakes up and gives me this. Here are the laptop stats: Toshiba Satellite L455D-S5976 AMD Sempron SI-42 Processor 2GB DDR2 RAM HD TruBrite Display ATI Radeon Graphics (integrated) Running Ubuntu 10.10 32 bit I'm not sure about the hard drive, but its a 250GB drive with one NTFS partition, two Hidden NTFS, one Linux Swap, and one Ext4. Can someone tell me whats wrong with my laptop? NOTE: This only happens when I close the screen. My computer doesn't go to sleep with the screen open.

    Read the article

  • How a batch file runs on a remote machine started by PSEXEC

    - by user38780
    I am having an issue running a Batch file on a remote machine suing PSEXEC. The file runs but does not run like it does when run through remote desktop. The batch runs a file which is a 32 bit application, which opens multiple 16bit applications, this should all run under one ntvdm.exe (In one Memory Space). Through remote desktop the batch file runs under the explorer process, and works correctly opening only one ntvdm.exe. Using PSEXEC the batch runs but not under the explorer process, a separate ntvdm.exe is open for each process. I found running the batch from explorer in PSEXEC works, but comes up with a "File Download - Security Warning" eg. psexec.exe" \compname -u username -p passowrd -s -d -i 0 explorer C:\Program.bat I want to be able to run the batch successfully without receiving warnings, it is a local warning and not a network share warning. Possible to recreate warning typing "explorer C:\windows\system32\cmd.exe" in Run I would like to know if anyone knows of a way to get PSEXEC to open the batch file to run as though it was started by explorer. Or a way of removing the local "File Download - Security Warning" Thanks

    Read the article

  • DRBD on a disk with existing file system that takes all the place

    - by Karolis T.
    I'm currently trying to simulate the environment via XEN. I have installed two debian systems with such FS layout: cltest1:/etc# df -h Filesystem Size Used Avail Use% Mounted on /dev/xvda2 6.0G 417M 5.2G 8% / tmpfs 257M 0 257M 0% /lib/init/rw udev 10M 16K 10M 1% /dev tmpfs 257M 4.0K 257M 1% /dev/shm Host cltest2 is identical. Here's my drbd.conf global { minor-count 1; } resource mysql { protocol C; syncer { rate 10M; # 10 Megabytes } on cltest1 { device /dev/drbd0; disk /dev/xvda2; address 192.168.1.186:7789; meta-disk internal; } on cltest2 { device /dev/drbd0; disk /dev/xvda2; address 192.168.1.187:7789; meta-disk internal; } } I have not created filesystem on drbd0 Starting DRBD via init.d script errors out with: Starting DRBD resources: [ d(mysql) /dev/drbd0: Failure: (114) Lower device is already claimed. This usually means it is mounted. [mysql] cmd /sbin/drbdsetup /dev/drbd0 disk /dev/xvda2 /dev/xvda2 internal --set-defaults --create-device failed - continuing! Running: drbdadm create-md mysql gives: cltest1:/etc# drbdadm create-md mysql md_offset 6442446848 al_offset 6442414080 bm_offset 6442217472 Found ext3 filesystem which uses 6291456 kB current configuration leaves usable 6291228 kB Device size would be truncated, which would corrupt data and result in 'access beyond end of device' errors. You need to either * use external meta data (recommended) * shrink that filesystem first * zero out the device (destroy the filesystem) Operation refused. Command 'drbdmeta /dev/drbd0 v08 /dev/xvda2 internal create-md' terminated with exit code 40 drbdadm aborting As I understand, all of my problems are because I don't have unallocated disk space on xvda2. What are my options besides shrinking FS and connecting a separate physical disk? Can't the meta-data be stored on a file in the local filesystem?

    Read the article

  • Apache + mod_fcgid + perl = error 500

    - by f-aminov
    Hi guys! I'm trying to setup Apache2.2 with mod_fcgid and libapache2-mod-perl2 with no luck. I've created a fcgi-bin directory in the root directory of my website and put there a test.fcgi file with the following content: #!/usr/bin/perl use CGI; print "This is test.fcgi!\n"; While trying to access it via http://www.website.dom/fcgi-bin/test.fcgi I get error 500 (Internal Server Error). Here is my vhost config: <VirtualHost 95.131.29.226:8080> ServerName website.com DocumentRoot /var/www/data/website.com SuexecUserGroup user group ServerAlias www.website.com AddType application/x-httpd-php .php .php3 .php4 .php5 .phtml <Directory "/var/www/data/website.com/fcgi-bin/"> Options +ExecCGI Allow from all Order allow,deny AddHandler fcgid-script .fcgi </Directory> </VirtualHost> fcgid.conf: <IfModule mod_fcgid.c> AddHandler fcgid-script .fcgi SocketPath /var/lib/apache2/fcgid/sock IdleTimeout 3600 ProcessLifeTime 7200 MaxProcessCount 8 DefaultMaxClassProcessCount 2 IPCConnectTimeout 8 IPCCommTimeout 60 </IfModule> SuExec log: [2010-04-06 03:02:47]: uid: (500/equ) gid: (502/equ) cmd: test.fcgi Apache error log: test! test! [Tue Apr 06 03:02:51 2010] [notice] mod_fcgid: process /var/www/data/website.com/fcgi-bin/test.fcgi(26267) exit(communication error), terminated by calling exit(), return code: 0 [Tue Apr 06 03:02:53 2010] [notice] mod_fcgid: process /var/www/data/website.com/fcgi-bin/test.fcgi(26261) exit(server exited), terminated by calling exit(), return code: 0 I've no clue why I'm getting error 500, but when I'm trying to access this file using console ($ perl /var/www/data/website.com/fcgin-bin/test.fcgi) everthing works fine without any errors... Any suggestions on how to solve this problem would be greatly appreciated. Thank you!

    Read the article

  • What's the best way to telnet from a remote Windows PC without using RDP?

    - by Rob D.
    Three Networks: 10.1.1.0 - Mine 172.1.1.0 - My Branch Office 172.2.2.0 - My Branch Office's VOIP VLAN. My PC is on 10.1.1.0. I need to telnet into a Cisco router on 172.2.2.0. The 10.1.1.0 network has no routes to 172.2.2.0, but a VPN connects 10.1.1.0 to 172.1.1.0. Traffic on 172.1.1.0 can route to 172.2.2.0. All PCs on 172.1.1.0 are running Windows XP. Without disrupting anyone using those PCs, I want to open a telnet session from one of those PCs to the router on 172.2.2.0. I've tried the following: psexec.exe \\branchpc telnet 172.2.2.1 psexec.exe \\branchpc cmd.exe telnet 172.2.2.1 psexec.exe \\branchpc -c plink -telnet 172.2.2.1 Methods 1 and 2 both failed because telnet.exe is not usable over psexec. Method 3 actually succeeded in creating the connection, but I cannot login because the session registers my carriage return twice. My password is always blank because at the "Username:" prompt I'm effectively typing: Routeruser[ENTER][ENTER] It's probably time to deploy WinRM... Does anyone know of any other alternatives? Does anyone know how I can fix plink.exe so it only receives one carriage return when I use it over psexec?

    Read the article

  • Powershell: Execute exe on remote server and capture output

    - by user364825
    I am trying to script the execution of an installer on remote web servers. The installer in question is also a Windows Service that hosts NServiceBus. If RDP'd into the server, the application is installed by the following command: &"$theInstaller" /install /serviceName:TheServiceName The installer prints output about its progress registering the service and connecting to the database to stdout, among other things. This works fine from an RDP session, but when I execute it remotely via PS, I get a you-can't-do-this-over-the-network message if I execute it directly or via Invoke-Command -computername $theRemoteServer: System.IO.FileLoadException: Could not load file or assembly 'file://\\theRemoteServer\c$ \thePath\AutoMapper.dll' or one of its dependencies. Operation is not supported. (Exception from HRESULT: 0x80131515) --- System.NotSupportedException: An attempt was made to load an assembly from a network location which would have caused the assembly to be sandboxed in previous versions of the .NET Framework. This release of the .NET Framework does not enable CAS policy by default, so this load may be dangerous. If this load is not intended to sandbox the assembly, please enable the loadFromRemoteSources switch. See http://go.microsoft.com/fwlink/?LinkId=155569 for more information. (Note: I added an additional "\" to the path in the first line in order to get it to show up correctly in the preview on this site.) This, and other DLLs, are loaded by the service, and the service's execution context cannot, apparently, be remotified. I have also tried using Invoke-WmiMethod, which does something, but it's not clear what, and the output from the installer is lost: Invoke-WMIMethod win32_process create '"$theInstaller" /install /serviceName:TheServiceName' -ComputerName $server (with and without cmd.exe /k before the intaller reference): __GENUS : 2 __CLASS : __PARAMETERS __SUPERCLASS : __DYNASTY : __PARAMETERS __RELPATH : __PROPERTY_COUNT : 2 __DERIVATION : {} __SERVER : __NAMESPACE : __PATH : ProcessId : ReturnValue : 9 How does one remotely execute such an EXE and capture the output? Thanks!

    Read the article

  • Ubuntu raid 1 write errors

    - by Micah
    I have an Ubuntu server set up with two SATA drives in a RAID 1 configuration with MDADM. The machine is used to record raw video, which involves a lot of writing to the disk. Sometimes during video recording the computer will crash, will the following errors in kern.log: Mar 15 10:39:41 video kernel: [414501.629864] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x400100 action 0x6 Mar 15 10:39:41 video kernel: [414501.629870] ata2.00: BMDMA stat 0x26 Mar 15 10:39:41 video kernel: [414501.629875] ata2.00: SError: { UnrecovData Handshk } Mar 15 10:39:41 video kernel: [414501.629880] ata2.00: failed command: WRITE DMA EXT Mar 15 10:39:41 video kernel: [414501.629889] ata2.00: cmd 35/00:00:28:6d:f6/00:04:06:00:00/e0 tag 0 dma 524288 out Mar 15 10:39:41 video kernel: [414501.629891] res 51/84:b1:77:6e:f6/84:02:06:00:00/e0 Emask 0x30 (host bus error) Mar 15 10:39:41 video kernel: [414501.629896] ata2.00: status: { DRDY ERR } Mar 15 10:39:41 video kernel: [414501.629899] ata2.00: error: { ICRC ABRT } Mar 15 10:39:41 video kernel: [414501.629910] ata2.00: hard resetting link Mar 15 10:39:41 video kernel: [414501.973009] ata2.01: hard resetting link Mar 15 10:39:41 video kernel: [414502.482642] ata2.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 15 10:39:41 video kernel: [414502.482658] ata2.01: SATA link down (SStatus 0 SControl 300) Mar 15 10:39:41 video kernel: [414502.546160] ata2.00: configured for UDMA/133 Mar 15 10:39:41 video kernel: [414502.546203] ata2: EH complete Is this the result of faulty drives? Is software RAID just not performant enough for data rates ~15 MB/s, even with a quad-core i7? Thanks for your help. Edit: cat /proc/mdstat returns this: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdb1[1] sda1[0] 976760768 blocks [2/2] [UU] unused devices: <none>

    Read the article

  • Cannot Delete Item "Could Not Find This Item" issue

    - by aronchick
    A friend sent a long a file (a .rar) he wanted me to check out for him before he installed it. I downloaded it and unrared it with no problems, but it was full of .exe's instead of the intended contents (fonts) so I advised him to delete it immediately and not use. I then proceeded to do the same, but the folder simply will not delete. Oddly the files went fine, and I never ran anything, but this is what I'm seeing: Could not find this item This is no longer located in C:\Users\This_User\Desktop. verify the item's location and try again. I've tried the following things with no help: Using "Unlocker" to Unlock and delete Using move on reboot and rebooting Using PendMoves (from sysinternals) and rebooting Elevating a cmd line, doing a dir /x to get the short name of the folder, and then del 'shortna~1' Moving the folder to a new folder and then trying to delete the parent folder I'm on Windows 7 RTM, very fresh install. Any thoughts? Update: Just to confirm, I've run Hijack this and half a dozen other malware detectors, and everything came back clean (no extra processes, no other obvious badness). Rebooting in safe mode didn't help either.

    Read the article

  • Toshiba laptop cd drive read causes OS to totally freeze

    - by Fujishiro
    Okay I'll try to write an understandable summary. Forgive me if I'll fail with that attempt though. So. There is a Toshiba Satellite notebook. Got Windows 7 x86 Professional (OEM) installed on it, everything is fine (okay.. somewhat). The problem. If you put an audio or any kind of disc into the drive, something starts to eat the PC. Back then when the owner told me about this, he put an audio disc into the lappy. Winamp caused the IO load, 100%. Tried taskkill, taskkill /T, tried powershell, EVERYTHING. You just can NOT kill winamp or anything which becomes the blocker at that time. Even if you kill almost everything, laptop won't do a clear shutdown. Also I tried to use the force switch at 'shutdown' from cmd, but no use. (So: At these times you can use the laptop, but the blocker/explorer/disc becomes gray as a non-responding app. You can try to kill them, but that won't work, nor you can shutdown the machine). (Also tried using PID, but no use. For the highest IO I used the "select columns" from Task Manager and enabled the IO columns.) My first hunch was the problematic disc, autoplay and it tries to read tries to read (still shouldn't kill the PC). Disabled autoplay, removed winamp. Tried other software, etc. Everything was ok. Few days later the owner tried to put a disc into the machine and it started to reproduce the same symptoms but with a totally different disc. Uhm what to know. Virus is not an option, protected by BitDefender (valid license) and Spybot. Thanks if you have ANY idea about this strange problem. ps.: For now, the owner uses Daemon tools + Blindwrite as an alternative for those apps which wouldnt start without the disc.

    Read the article

  • nameserver spoiling avahi multicast name resolution of .local domain

    - by Doug Coburn
    After trying to ping a machine on my local network, I noticed that I was trying hit address 66.152.109.24. This is an external public address. Resolution should have occurred via avahi mDNS. I ran dig to see how the name resolution worked and my quest/centurylink name server was retuning results for my .local domain queries! I tried a random name and got the same ip address result. $ dig jakdafj.local ; <<>> DiG 9.8.1-P1-RedHat-9.8.1-3.P1.fc15 <<>> jakdafj.local ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 58410 ;; flags: qr rd ra; QUERY: 1, ANSWER: 2, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;jakdafj.local. IN A ;; ANSWER SECTION: jakdafj.local. 10 IN A 66.152.109.24 jakdafj.local. 10 IN A 204.232.231.46 ;; Query time: 104 msec ;; SERVER: 205.171.3.25#53(205.171.3.25) ;; WHEN: Sat Mar 24 20:40:17 2012 ;; MSG SIZE rcvd: 63 Am I missing something or is my DNS name server at 205.171.3.25 corrupted?

    Read the article

  • Drop database on DB2 9.5 - SQL1035N The database is currently in use

    - by Tommy
    I've never got this working the first time, but now I can't seem to do i at all. There is a connection pool somewhere using the database, so trying to drop the database when an application is using the database should give this error. The problem is there are no connection to the database when I issue these commands: db2 connect to mydatabase db2 quiesce database immediate force connections db2 connect reset db2 drop database mydatabase This allways give: SQL1035N The database is currently in use. SQLSTATE=57019 running this command shows no connections/applications DB2 list applications I can even deactivate the database, but still can't drop it. db2 => deactivate database mydatabase DB20000I The DEACTIVATE DATABASE command completed successfully. db2 => drop database mydatabase SQL1035N The database is currently in use. SQLSTATE=57019 db2 => Anyone got any clues? I'm running the cmd-windows as the local administrator (windows 2008) and this is also the admin for DB2. The connectionpool-user cannot connect during quiesce-state.

    Read the article

  • Dlink DWA-556 Access point fails to start on 2.6.35-25 while 2.6.35-24 works. How can I do this with >2.6.35-24?

    - by Azendale
    I'm using hostapd to run an access point with a Dlink DWA-556 wireless N card. However, I can no longer get it to start when I use kernels greater than 2.6.35-24. Here's a log where I ran the uname -a&&hostapd -c <configfile> on the different kernel versions. Linux erikbandersen 2.6.35-24-generic #42-Ubuntu SMP Thu Dec 2 02:41:37 UTC 2010 x86_64 GNU/Linux Configuration file: hostapd.conf ctrl_interface_group=0 Opening raw packet socket for ifindex 248 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf nl80211: Added 802.11b mode based on 802.11g information HT40: control channel: 2 secondary channel: 6 RATE[0] rate=10 flags=0x2 RATE[1] rate=20 flags=0x6 RATE[2] rate=55 flags=0x6 RATE[3] rate=110 flags=0x6 RATE[4] rate=60 flags=0x0 RATE[5] rate=90 flags=0x0 RATE[6] rate=120 flags=0x0 RATE[7] rate=180 flags=0x0 RATE[8] rate=240 flags=0x0 RATE[9] rate=360 flags=0x0 RATE[10] rate=480 flags=0x0 RATE[11] rate=540 flags=0x0 Passive scanning not supported Mode: IEEE 802.11g Channel: 2 Frequency: 2417 MHz Flushing old station entries Deauthenticate all stations Using interface wlan1 with hwaddr 1c:bd:b9:d5:e8:3c and ssid 'erikbandersen.com/freewifi' wlan1: Setup of interface done. MGMT (TX callback) ACK Malformed netlink message: len=436 left=256 plen=420 256 extra bytes in the end of netlink message MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb mgmt::auth authentication: STA=3c:4a:92:0e:41:2f auth_alg=0 auth_transaction=1 status_code=0 wep=0 New STA wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: authentication OK (open system) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-AUTHENTICATE.indication(3c:4a:92:0e:41:2f, OPEN_SYSTEM) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) authentication reply: STA=3c:4a:92:0e:41:2f auth_alg=0 auth_transaction=2 resp=0 (IE len=0) MGMT (TX callback) ACK mgmt::auth cb wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: authenticated mgmt::assoc_req association request: STA=3c:4a:92:0e:41:2f capab_info=0x421 listen_interval=10 Validating WMM IE: OUI 00:50:f2 OUI type 2 OUI sub-type 0 version 1 QoS info 0x0 HT: STA 3c:4a:92:0e:41:2f HT Capabilities Info: 0x102c handle_assoc STA 3c:4a:92:0e:41:2f - no greenfield, num of non-gf stations 1 handle_assoc STA 3c:4a:92:0e:41:2f - 20 MHz HT, num of 20MHz HT STAs 1 hostapd_ht_operation_update current operation mode=0x0 hostapd_ht_operation_update new operation mode=0x7 changes=2 new AID 1 wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: association OK (aid 1) MGMT (TX callback) ACK mgmt::assoc_resp cb wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: associated (aid 1) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-ASSOCIATE.indication(3c:4a:92:0e:41:2f) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) wlan1: STA 3c:4a:92:0e:41:2f RADIUS: starting accounting session 4DAC8224-00000000 MGMT (TX callback) ACK mgmt::action cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb Signal 2 received - terminating wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DEAUTHENTICATE.indication(3c:4a:92:0e:41:2f, 1) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) Removing station 3c:4a:92:0e:41:2f hostapd_ht_operation_update current operation mode=0x7 hostapd_ht_operation_update new operation mode=0x0 changes=2 Flushing old station entries Deauthenticate all stations . Linux erikbandersen 2.6.35-25-generic #44-Ubuntu SMP Fri Jan 21 17:40:44 UTC 2011 x86_64 GNU/Linux Configuration file: hostapd.conf ctrl_interface_group=0 Opening raw packet socket for ifindex 248 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf nl80211: Added 802.11b mode based on 802.11g information Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=27 dBm HT40: control channel: 2 secondary channel: 6 RATE[0] rate=10 flags=0x2 RATE[1] rate=20 flags=0x6 RATE[2] rate=55 flags=0x6 RATE[3] rate=110 flags=0x6 RATE[4] rate=60 flags=0x0 RATE[5] rate=90 flags=0x0 RATE[6] rate=120 flags=0x0 RATE[7] rate=180 flags=0x0 RATE[8] rate=240 flags=0x0 RATE[9] rate=360 flags=0x0 RATE[10] rate=480 flags=0x0 RATE[11] rate=540 flags=0x0 Passive scanning not supported Mode: IEEE 802.11g Channel: 2 Frequency: 2417 MHz Could not set channel for kernel driver wlan1: Unable to setup interface. My wireless card is listed as 02:00.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) by lspci. Am I doing it wrong and there's a new way of doing it? I'm holding off upgrading to Natty because of this. What changed between the versions that would cause this? Should I report it as a bug?

    Read the article

  • Hard drive failed, suspected filesystem corruption, still cannot salvage any data from harddrive

    - by Hippy-Head
    Firstly, I am terribly sorry if this is a duplicate, but I couldn't find a similar issue to mine, so here goes. I have a 1TB hdd bought around 8 months ago used as backup hard drive. I have not used the drive for a period of time whatsoever, and when I was trying to get back to some files on it, it was completely wiped just like that. At first it would not boot I tried everything from command line chkdsk and filesystem recovery software to rebuilt it. After a few attempts I managed to initialize it, at that time it was an achievement. The problems started when I tried to recover the data inside, I have used A LOT of software free and commercial software on both Mac and Windows, with the help of cmd or Terminal commands, however no data of any kind was recovered, even after leaving it thoroughly scan for around 9-10 hours all night sometimes longer, with no results at all. I am somewhat desperate, I am usually good at retrieving data from corrupt hard drives, but this is not the case. Call me paranoid, but I do not want to give it to someone to fix it for me, as I have a lot of photos and personal stuff that I do not want anyone to see.

    Read the article

  • All browsers refusing to load a specific image on a webpage?

    - by Johnson
    Out of nowhere today, all 3 of my browsers (FF/Chrome/IE, OS = Win7 x64) are refusing to load the homepage of interfacelift.com correctly. It works fine on other PC's in the house (on the same network), so it is definitely related to this one PC. The browser won't load the main image on the page correctly (even though the source code looks good), however if I direct the browser to the exact location of that image, then it displays fine. So obviously I can get the HTML index (which locates the resource) and I can get to the resource. So why heck isn't it displaying properly on the index page? It's almost as if the HTML rendering engine has gone bad, on all 3 browsers at once. I've browsed to a bunch of other sites (including sites very heavy on JS, with HTML much more complex than the one in question here) and am seeing nothing funny. Only thing wonky I've done with my PC in the past several hours was replacing the system file Magnifier.exe with a copy of cmd.exe while playing around with some of the ideas mentioned in this guide. However, I've since then restored the files to their previous state, and I don't know how Magnifier would be related to this even if I hadn't restored it. Any ideas? I'm stumped! EDIT: Here is what the broken page looks like in Chrome. And here is the image loaded correctly by itself.

    Read the article

  • Issue running 32-bit executable on 64-bit Windows

    - by David Murdoch
    I'm using wkhtmltopdf to convert HTML web pages to PDFs. This works perfectly on my 32-bit dev server [unfortunately, I can't ship my machine :-p ]. However, when I deploy to the web application's 64-bit server the following errors are displayed: (running from cmd.exe) C:\>wkhtmltopdf http://www.google.com google.pdf Loading pages (1/5) QFontEngine::loadEngine: GetTextMetrics failed () ] 10% QFontEngineWin: GetTextMetrics failed () QFontEngineWin: GetTextMetrics failed () QFontEngine::loadEngine: GetTextMetrics failed () QFontEngineWin: GetTextMetrics failed () QFontEngineWin: GetTextMetrics failed () QFontEngineWin: GetTextMetrics failed () QFontEngine::loadEngine: GetTextMetrics failed () ] 36% QFontEngineWin: GetTextMetrics failed () QFontEngineWin: GetTextMetrics failed () // ...etc.... and the PDF is created and saved... just WITHOUT text. All form-fields, images, borders, tables, divs, spans, ps, etc are rendered accurately...just void of any text at all. Server information: Windows edition: Windows Server Standard Service Pack 2 Processor: Intel Xeon E5410 @ 2.33GHz 2.33 GHz Memory: 8.00 GB System type: 64-bit Operating System Can anyone give me a clue as to what is happening and how I can fix this? Also, I wasn't sure what to tag/title this question with...so if you can think of better tags/title comment them or edit the question. :-)

    Read the article

< Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >