Search Results

Search found 11111 results on 445 pages for 'fahnz mode'.

Page 98/445 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >

  • Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

    - by Kevinoid
    Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated.

    Read the article

  • Partition is missing in /dev

    - by haimg
    I'm having a strange problem since I moved from Centos5 to Centos6. I have three disks, first two are used as a RAID1, and third one is a stand-alone backup disk that is not listed in /etc/fstab (it is mounded when needed and then unmounted). My problem: After a boot, /dev/sdc exists but /dev/sdc1 does not. Also, the links in /dev/disks are also absent for the first partition of sdc. Disk itself is fine, and if I hot-remove it and plug it back in, /dev/sdc1 appears ok and everything is working. My question: What subsystem manages auto-discovery of disks, partitions, etc. during the boot process (e.g. what creates /dev/disks/by-label)? How do I configure it to scan /dev/sdc too and create all relevant files and links in /dev ? Edit: Here's the relevant part of dmesg output (the only place sdc appears). It does list sdc1, but it's not in /dev! sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 3:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 3:0:0:0: [sdc] Write Protect is off sd 3:0:0:0: [sdc] Mode Sense: 00 3a 00 00 sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdc: sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: DMAR:[DMA Read] Request device [00:1e.0] fault addr 361bc000 DMAR:[fault reason 06] PTE Read access is not set sdb1 sdb2 sdb3 sdc1 sda1 sd 1:0:0:0: [sdb] Attached SCSI disk sd 3:0:0:0: [sdc] Attached SCSI disk sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk

    Read the article

  • Emacs 24.1: How do I restore i-search Ctrl-Y behavior from older versions?

    - by Eric
    In emacs 24.1, when you do Ctrl-Y in an interactive search, it yanks the kill buffer into the search string ("it pastes the clipboard contents" in any-other-app's language) and tries to match it. In the last 20 versions or so, pressing Ctrl-Y matches the rest of the current line. I have two very common use cases: Match this line, revert the buffer, and search for the line (less often:) Where else is this text in the buffer? I tried modifying /lisp/isearch.el, switching the bindings for isearch-yank-line (which I want) and isearch-yank-kill (which I'm fine binding to the ridiculous \M-s\C-e key sequence). But I don't think this file even gets picked up. But I don't think this file even gets loaded. If I explicitly load it, I still get the 24.1 behavior. Here's my change: (add-hook 'isearch-mode-hook (lambda () (define-key isearch-mode-map "\C-y" 'isearch-yank-line) (define-key isearch-mode-map "\M-s\C-e" 'isearch-yank-kill) )) No change in the behavior. I even tried hacking isearch.el, still no change. This is on Windows btw, but I suspect it doesn't matter. Could someone tell me how I can restore the old binding?

    Read the article

  • Rackspace Ubuntu 12.04 server stuck in initramfs after kernel upgrade

    - by Znarkus
    Can't boot after I did a aptitude full-upgrade and let it update menu.lst (did a diff first and it looked good). This is what I've done so far in the BusyBox shell: mkdir /tmp/xvda1 mount /dev/xvda1 /tmp/xvda1 chroot /dev/xvda1 nano /boot/grub/menu.lst This file looks like this: title Ubuntu 12.04.1 LTS, kernel 3.2.0-31-virtual root(hd0,0) kernel /boot/vmlinuz-3.2.0-31-virtual root=UUID=/dev/xvda1 ro quiet splash initrd /boot/initrd.img-3.2.0-31-virtual title Ubuntu 12.04.1 LTS, kernel 3.2.0-31-virtual (recovery mode) root(hd0,0) kernel /boot/vmlinuz-3.2.0-31-virtual root=UUID=/dev/xvda1 ro single initrd /boot/initrd.img-3.2.0-31-virtual titleUbuntu 12.04.1 LTS, kernel 3.2.0-24-virtual root(hd0,0) kernel/boot/vmlinuz-3.2.0-24-virtual root=UUID=/dev/xvda1 ro quiet splash initrd/boot/initrd.img-3.2.0-24-virtual titleUbuntu 12.04.1 LTS, kernel 3.2.0-24-virtual (recovery mode) root(hd0,0) kernel/boot/vmlinuz-3.2.0-24-virtual root=UUID=/dev/xvda1 ro single initrd/boot/initrd.img-3.2.0-24-virtual titleUbuntu 12.04.1 LTS, kernel 3.2.0-24-generic root(hd0,0) kernel/boot/vmlinuz-3.2.0-24-generic root=UUID=/dev/xvda1 ro quiet splash initrd/boot/initrd.img-3.2.0-24-generic titleUbuntu 12.04.1 LTS, kernel 3.2.0-24-generic (recovery mode) root(hd0,0) kernel/boot/vmlinuz-3.2.0-24-generic root=UUID=/dev/xvda1 ro single initrd/boot/initrd.img-3.2.0-24-generic titleChainload into GRUB 2 root(hd0,0) kernel/boot/grub/core.img titleUbuntu 12.04.1 LTS, memtest86+ root(hd0,0) kernel/boot/memtest86+.bin From what I remember, the upgrade added the UUID= string. Should I remove these? Or rather, how do I get my system back online again? Thanks. Update: Seems like I can't even edit the file. [ Error writing /boot/grub/menu.lst: Read-only file system ]

    Read the article

  • ftp.exe does not convert end of line characters while transferring to FreeBSD ftp server

    - by Jagger
    I am having problems transferring a text file from Windows 7 using ftp.exe to a FreeBSD server. After the file transfer the end-of-line characters are not changed from \r\n to \n, Instead they remain with the carriage return character which can be seen in for example mcedit as ^M. The file is transferred in ascii mode. Has anybody run into similar problems in the past? As far as I know using the ascii mode during FTP transfer should convert those characters automatically. Does it depend on the server configuration? EDIT: The file can be seen here. EDIT: I have also tried with ncftp.exe under Cygwin but the result is the same. The carriage return character has not been removed even if the transfer type was ASCII. EDIT: It does not work the other way round either. I created a text file in FreeBSD and then downloaded it is ASCII mode to my Windows machine. The end of line characters remained LF as they were in FreeBSD.

    Read the article

  • xen + debian network after upgrade squeeze to wheeze

    - by rush
    I've got a Debian + Xen server. After a system upgrade to the stable version the network doesn't come up after boot. Every time after reboot I need to bring it up manually. The network configuration was not changed during upgrade. Here is /etc/network/interfaces: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 11.22.33.44 netmask 255.255.255.0 gateway 11.22.33.1 nameserver 8.8.8.8 After boot ip r shows no route and eth0 has no ip address. Manually ip and route setup goes fine and network starts working. Messages from dmesg about network I've found (looks like nothing interesting) [ 3.894401] ACPI: Fan [FAN3] (off) [ 3.894444] ACPI: Fan [FAN4] (off) [ 4.178348] e1000e 0000:00:19.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c9 [ 4.178351] e1000e 0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection [ 4.178392] e1000e 0000:00:19.0: eth0: MAC: 10, PHY: 11, PBA No: 0100FF-0FF [ 4.178413] e1000e 0000:02:00.0: Disabling ASPM L0s L1 [ 4.178432] xen: registering gsi 16 triggering 0 polarity 1 -- [ 4.223667] ata5: DUMMY [ 4.223668] ata6: DUMMY [ 4.289153] e1000e 0000:02:00.0: eth1: (PCI Express:2.5GT/s:Width x1) 00:1e:67:14:66:c8 [ 4.289155] e1000e 0000:02:00.0: eth1: Intel(R) PRO/1000 Network Connection [ 4.289245] e1000e 0000:02:00.0: eth1: MAC: 3, PHY: 8, PBA No: 1000FF-0FF [ 4.506908] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 4.542920] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) -- [ 10.362999] EXT4-fs (dm-23): mounted filesystem with ordered data mode. Opts: (null) [ 10.419103] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) [ 10.988255] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 13.175533] Event-channel device installed. [ 13.287555] XENBUS: Unable to read cpu state -- [ 13.288670] XENBUS: Unable to read cpu state [ 13.965939] Bridge firewalling registered [ 14.134048] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 14.283862] ADDRCONF(NETDEV_UP): peth0: link is not ready [ 14.284543] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 17.800627] e1000e: peth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx [ 17.801377] ADDRCONF(NETDEV_CHANGE): peth0: link becomes ready [ 18.307278] device peth0 entered promiscuous mode [ 24.538899] eth1: no IPv6 routers present [ 28.570902] peth0: no IPv6 routers present I've upgraded two servers and I've such behaviour on two of them. How to fix this and get network starts automatically on boot?

    Read the article

  • Quickly close all Word and Excel instances?

    - by dyenatha
    Suppose I open 10 Word files and 10 Excel files and make no changes, how do I quickly taskkill all at once? Because I must repeat several attempts to replicate race, I'm hoping for a command-line solution. I'm willing to try PowerShell and cygwin (1.5) if necessary. The OS is Windows XP SP3 with current patches (still IE7). I tried "taskkill /pid 1 /pid 2 /t" where 1 is PID of EXCEL.EXE and 2 is PID of WINWORD.EXE, but it closed only 1 window of each program. I'm trying to replicate a race where an add-in for Microsoft Office 2007 fails to exclusive-lock one of its own files, which caused the 2nd Office program to stop exiting with a warning: System.IO.IOException: The process cannot access the file 'C:\Documents and Settings\me\Application Data\ExpensiveProduct\Add-InForMicrosoftOffice\4.2\egcred' because it is being used by another process. at System.IO.__Error.WinIOError(Int32 errorCode, String maybeFullPath) at System.IO.FileStream.Init(String path, FileMode mode, FileAccess access, Int32 rights, Boolean useRights, FileShare share, Int32 bufferSize, FileOptions options, SECURITY_ATTRIBUTES secAttrs, String msgPath, Boolean bFromProxy) at System.IO.FileStream..ctor(String path, FileMode mode, FileAccess access, FileShare share, Int32 bufferSize, FileOptions options) at System.IO.StreamWriter.CreateFile(String path, Boolean append) at System.IO.StreamWriter..ctor(String path, Boolean append, Encoding encoding, Int32 bufferSize) at System.IO.StreamWriter..ctor(String path, Boolean append, Encoding encoding) at System.IO.File.WriteAllText(String path, String contents, Encoding encoding) at ExpensiveProduct.EG.DataAccess.Credentials.CredentialManager.SaveUserTable() at ExpensiveProduct.OfficeAddin.OfficeAddinBase.Dispose(Boolean disposing) at ExpensiveProduct.OfficeAddin.WordAddin.Dispose(Boolean disposing) at ExpensiveProduct.OfficeAddin.OfficeAddinBase.OnHostShutdown() at ExpensiveProduct.OfficeAddin.OfficeAddinBase.Unload(ext_DisconnectMode mode)

    Read the article

  • how is the the linux console displayed to the user and how does the user go about changing the conso

    - by Chris
    I've been searching for the last two day on trying to understand how the console displays itself to the user and how to change the console settings. I've had some luck along the way but nothing that I've found has giving me a real clear explanation of how the console is displayed or how to change or control it's display settings. Some examples that of what I'm looking for are as follows: How is the console displayed on the screen? I know with X11 it uses your graphics card driver to display graphics to the screen, but how is the consoles text mode handled? Could some one ether explain this to me or point me to an in-depth overview of it all? Is it possible to have multi-head support in console mode with separate tty's on each screen? If so how would I go about setting this up? How would you go about changing the size of the console display from the default 80x25 to a custom size? I'm testing anything I find on a debian testing build, which is just the minimal base install on a virtual box. In time I will be using this information to setup my main system which is multi-head with 3 monitors. I would like to be able to support all three displays in console mode if possible.

    Read the article

  • Win 7 Remote Desktop connection failure when already logged in.

    - by Andy E
    I have a bit of a strange problem, magnified recently by my broadband dropouts. I wasn't sure whether to post this on SU or SF, so I thought I'd start here as more users would be likely to know what the problem is. In short, when I try and connect to my server (Windows Server 2008) from my laptop running Windows 7, I can only connect if my remote account was previously logged out. If I'm still logged in I get the error message: Windows cannot connect to the remote server. No explanation or anything. If my IP address is the same, I don't have this problem. If I boot up Windows XP Mode and run XP's remote desktop connection it works just fine -- I think the difference there is it takes me to the remote server's logon screen. With Win 7 RDC you never see the logon screen, it asks you for credentials before entering full screen mode. The real problem is that I'm having random broadband dropouts and my IP isn't static. If I logon via Win XP RDC, log out and then run Win 7 RDC then it works fine. I realize I can just use Win XP's RDC for now, but I don't really like keeping XP Mode open if I can help it. Does anyone know a way around this problem? Maybe forcing Win 7 RDC to go to the logon screen, or changing some server-side settings to work around the IP address issue?

    Read the article

  • How can I start hostednetwork on Windows 7?

    - by Pirozek
    When I type in admin console command to start hostednetwork netsh wlan start hostednetwork it gives me this: The hosted network couldn't be started. The group or resource is not in the correct state to perform the requested operation. There is a hotfix from Microsoft but it didn't help me. Any advice? C:\Users\Pirozek>netsh wlan show driver Interface name: Wireless Network Connection 3 Driver : D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev .B) Vendor : Atheros Communications Inc. Provider : Atheros Communications Inc. Date : 8.7.2009 Version : 8.0.0.171 INF file : C:\Windows\INF\oem108.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g FIPS 140-2 mode supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Shared WEP-40bit Open WEP-104bit Shared WEP-104bit Open WEP Shared WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP

    Read the article

  • What's Keeping My Computer Awake?

    - by phantomdata
    First the question; How do I figure out what is preventing my Windows 7 computer from going into sleep mode? Second; some background... I've been struggling with this for a few days and am utterly perplexed. I setup sleep mode on my Windows 7 PC a few weeks ago, and all was well. The PC would sleep as expected and I was snuggly in knowing that my computer was saving power and some wear and tear on the components (we'll leave the 'is it better to sleep' debate for another thread/day, please don't start it). Well, I noticed the other night that my system stopped ever going to sleep. I set the sleep time down to 1 minute and wandered fully away from the PC (ensuring that no errant mouse or keyboard movements would occur) and the PC never went to sleep. I've also observed this over longer intervals as well, such as overnight. I have sleep mode enabled, of course "multimedia settings - When Sharing Media" is set to allow the computer to sleep. "powercfg -lastwake" show nothing of interest, since it never goes to sleep and can't wake up. "powercfg /requests" shows 3 entries - all "[DRIVER] ?". I assume that 2 of these are my mouse and keyboard - as I've recently used them to run the powercfg command. I'm at a loss for the third though. I've unhooked all USB peripherals save for my keyboard and mouse. Wake on LAN is disabled in my BIOS. I know that you can disable all apps from waking/preventing sleep - but I want the ability to remain for those apps that do legitimately need to keep the system awake. So; does anyone know of a way to figure out what the 3rd phantom "[DRIVER] ?" is in powercfg /requests?

    Read the article

  • Can Haproxy deny a request by IP if its stick-table is full?

    - by bantic
    In my haproxy configs I'm setting a stick-table of size 5 that stores every incoming IP address (for 1 minute), and it is set as nopurge so new entries won't get stored in the table. What I'd like to have happen is that they would get denied, but that isn't happening. The stick-table line is: stick-table type ip size 5 expire 1m nopurge store gpc0 And the whole configs are: global maxconn 30000 ulimit-n 65536 log 127.0.0.1 local0 log 127.0.0.1 local1 debug stats socket /var/run/haproxy.stat mode 600 level operator defaults mode http timeout connect 5000ms timeout client 50000ms timeout server 50000ms backend fragile_backend tcp-request content track-sc2 src stick-table type ip size 5 expire 1m nopurge store gpc0 server fragile_backend1 A.B.C.D:80 frontend http_proxy bind *:80 mode http option forwardfor default_backend fragile_backend I have confirmed (connecting to haproxy's stats using socat readline /var/run/haproxy.stat) that the stick-table fills up with 5 IP addresses, but then every request after that from a new IP just goes straight through -- it isn't added to the stick-table, nothing is removed from the stick-table, and the request is not denied. What I'd like to do is deny the request if the stick-table is full. Is this possible? I'm using haproxy 1.5.

    Read the article

  • Excel controls not visible for certain users

    - by Nossidge
    One of the users of an Excel program I've written is having a weird problem. None of the control objects (Command Button, ComboBox, etc.) are visible to him when he opens the file on his laptop. He is using Excel 2003, the same version I used to create the program, and enables macros using the pop-up when the file loads. I have Googled this, and have found these people who seem to be having the exact same problem, with various versions of Excel. Unfortunately, none of their questions were answered. I can't really explain it any better than this user: If I enter design mode and pull a control from the control toolbar onto a sheet all I see are the drag handles. When not in design mode I have to feel around with the mouse and can click the button which executes the button click code correctly and opens another sheet where again I have to feel around for the buttons to return me to the original sheet. The button I managed to click is now visible but as soon as I click anywhere on the sheet it disappears. I have verified that the visible property of the buttons is set and that the Show All Objects on the Options View tab is selected. If I pull buttons from the Forms toolbar onto a sheet they are visible. If I try to find Objects using F5 when not in design mode Excel reports no objects on the sheet. So, Super Users, can you help? UPDATE: Thanks for your replies, but much like the person in the ozgrid link, the problem has gone away. Not sure why it went, but I can confirm that the user rebooted again and also started up other Excel files that didn't contain controls in the interim. Perhaps that fixed it, or maybe it'll be back again. I'll keep udating with progress, and close if the problem doesn't reoccur for the next few days. Thanks again.

    Read the article

  • Is it possible to get ESC to behave as an actual escape key?

    - by leftaroundabout
    So I have finally switched, not so much because I'm yet convinced Emacs in itself is the better editor but because it certainly does have more powerful extensions. I am still using vim-mode though, perhaps that's part of my problem... but I really don't intend to abandon the modes-approach, so I'll probably stay with it. I'm getting along quite well, but one thing I find really unnerving is the behaviour of the esc key (which I have in the shift-lock position). I'm used to relying on this a lot as more or less a "panic key", which may not be nice but I find allows me to work generally quite a bit less caring about the keystrokes themselves, and thus faster. What I'd like this key to do is just get me out of any minibuffer or special editing mode into a well-defined normal state. Perhaps most importantly, I would like it to not do anything unrelated, Simulate meta. What do I have an alt key for? Close windows I'm not even in at the time. Getting interpreted as the final key in some key sequence. ... Is it possible to turn all that off and make esc an actual escape key? Vim-mode does make it behave kind of as I like in some situations, but when other plugins are involves this often breaks. Alternatively, are there different options that might suit my kind of workflow?

    Read the article

  • Network card shuts down when stressed

    - by user142485
    I have a network card that functions fine with light use, but quits functioning after heavy use. I replaced it with a brand new one and still have the same issue, also updated drivers. It is a wired D-Link card. The Internet seems fine for a small amount of web browsing but when I run a bandwidth test it starts out fast and slows quickly until the card completely quits; I have a constant ping of the gateway going while I run this and it starts timing out after a couple seconds into the speed test. The card will stay on and the data light on it still flashes some but I cannot ping the gateway or anything else until the computer is rebooted. When I boot into safe mode I can browse and run the speed test fine with no problems. I am guessing that this is probably some program that is loading in regular mode but not safe mode that is causing the issue? I have very limited software (turned off av and firewall) on the computer but I am thinking that I'll just have to start eliminating start-up programs and see if that helps. This is on Windows 7 if that makes any difference. Anyone had a similar issue or have any other suggestions/ideas for narrowing down this problem?

    Read the article

  • What's Keeping My Computer Awake?

    - by phantomdata
    Hey guys, First the question; How do I figure out what is preventing my Windows 7 computer from going into sleep mode? Second; some background... I've been struggling with this for a few days and am utterly perplexed. I setup sleep mode on my Windows 7 PC a few weeks ago, and all was well. The PC would sleep as expected and I was snuggly in knowing that my computer was saving power and some wear and tear on the components (we'll leave the 'is it better to sleep' debate for another thread/day, please don't start it). Well, I noticed the other night that my system stopped ever going to sleep. I set the sleep time down to 1 minute and wandered fully away from the PC (ensuring that no errant mouse or keyboard movements would occur) and the PC never went to sleep. I've also observed this over longer intervals as well, such as overnight. I have sleep mode enabled, of course "multimedia settings - When Sharing Media" is set to allow the computer to sleep. "powercfg -lastwake" show nothing of interest, since it never goes to sleep and can't wake up. "powercfg /requests" shows 3 entries - all "[DRIVER] ?". I assume that 2 of these are my mouse and keyboard - as I've recently used them to run the powercfg command. I'm at a loss for the third though. I've unhooked all USB peripherals save for my keyboard and mouse. Wake on LAN is disabled in my BIOS. I know that you can disable all apps from waking/preventing sleep - but I want the ability to remain for those apps that do legitimately need to keep the system awake. So; does anyone know of a way to figure out what the 3rd phantom "[DRIVER] ?" is in powercfg /requests?

    Read the article

  • Auto-focus xdvi after running viewdvi in Emacs with AUCTeX.

    - by D Connors
    I've been using emacs with AUCTeX mode to edit my latex documents for a few days now, but there's something that's really bugging me. As it should be, whenever I do C-c C-c RET it compiles the file, and if repeat the command it views the output in xdvi. It's also set to the mini-mode TeX-source-specials-mode, so instead of opening a new window in xdvi it only reloads the window that's already open, brings it to the front, and sends me to wherever the pointer was in emacs (forward search). Now here's the problem: Even though the xdvi window is brought to the front, it's not focused. Instead, the emacs windows stays with focus (and that's where any keyboard input goes). And I keep forgetting about that, which leads me to accidentally editing the source file while trying to navigate in xdvi. Not to mention I'm forced to alt-tab in order to focus xdvi, and alt-tab twice if I just want to get back to emacs. Is there a way around this problem? I just want xdvi to be focused whenever I run the view command from emacs.

    Read the article

  • Ubuntu loading stops ?

    - by joxnas
    I don't know why, or how... but my ubuntu's loading / booting stops right after the ubuntu logo appearing.. An underscore appears in the right top of the screen: _ then, it disappears leaving the whole screen black Version is 9.10 ,Kernel is .20 I have tryed recovering mode and selected recover damaged packages option, but it didn't do any good.. I have very important files in Ubuntu that I need to copy to a pen drive or something, today.. The terminal mode is working, so i think i can do this there.. My questions: How can I get my Ubuntu to load? Is it possible to copy the files i need via terminal mode? I dont know if with other of the previous kernels it would work... but I had configured my grub (inside Ubuntu's gui) to show only the last kernel... and now i can't select any other kernel then .20 because I don't know a way to configure Grub unless via Ubuntu's gui... My hardware: ATI Mobility Radeon 4650 HD P7450 2.13Ghz Core duo 4Gb DDR2

    Read the article

  • vim: mapping <control-j> key

    - by bhh1988
    When I'm in insert mode, I sometimes want to be able to move around without using the arrow keys, and without having to go back into normal mode. So in my vimrc I've set up key bindings to do this: imap <C-l> <right> imap <C-h> <left> imap <C-k> <up> imap <C-j> <down> But for some odd reason the only one that doesn't work is the last one, . Doing this in insert mode just gives no response. I'm wondering why this might be, and I just don't know where to even begin looking for the problem. It doesn't appear to be mapped to anything since nothing happens when I do it, whether I'm in the terminal or in gvim. Any pointers would be great! Thanks!

    Read the article

  • Win7 taskbar freezes on startup for about 1-2 mins

    - by Mike
    Running Win7 64-bit for about 4 months now. Never had this problem, didn't install anything new recently. When I boot up I can't do anything in the taskbar, it's frozen for about 1-2 minutes then everything is normal. I can right click on my desktop and move my mouse around. This randomly just started happening a couple days ago after a reboot. I have a 3.2ghz quad, SSD, 4 gig ram, etc. and it usually starts up quickly. After some troubleshooting (including running antivirus and Anti-Malware), it doesn't appear to be software related, but appears to be services related. I can boot up in safe mode and safe mode with networking just fine. I can also boot up normally with all my regular software loading at startup, BUT with all my services turned off. Now the odd part. When I run msconfig to disable all the services at startup and go through ticking them on 5-10 at a time or so and booting up it seems to be somewhat random. Ticking everything on from "Application Experience" halfway down to about "Quality Windows Audio Video Experience" and I can boot without the 1-2 min. freeze. Then I start ticking the stuff below that from a couple of Remote Accesses to Smart Card and Task Scheduler, etc. But the weird part is sometimes it will freeze sometimes it won't. I can't narrow it down. Then if it freezes, I'll boot up in safe mode and turn the ones I just turned on back off and I'll reboot normally but it will freeze again. Which makes no sense because that configuration just worked without freezing just before. I got frustrated enough that I backed up and wiped my hard drive (formatted and everything) and reinstalled Win7 but when I booted up, the freeze happened again. Any ideas? Thanks in advance.

    Read the article

  • Is it safe to format this partition?

    - by xanesis4
    On a ubuntu server I own, I am running out of space. When I ran sudo parted /dev/sda -l to find all available drives, I got this: Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1049kB 256MB 255MB primary ext2 boot 2 257MB 1000GB 1000GB extended 5 257MB 1000GB 1000GB logical lvm Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-swap_1: 2135MB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 2135MB 2135MB linux-swap(v1) Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/server--vg-root: 998GB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size File system Flags 1 0.00B 998GB 998GB ext4 I understand /dev/mapper/server--vg-root is the filesystem, and /dev/sda1 has some stuff related to GRUB. But, what about /dev/sda2 and /dev/sda5? When I tried to mount /dev/sda2, it said that I needed to specify the file system, which according to the table, is nonexistent. So, is it safe to format this with, say ext4 and mount it? Also, when I tried to mount /dev/sd5, it gave me this error: mount: unknown filesystem type 'LVM2_member' I assume it is NOT save to reformat this. If I'm wrong, then that would be great, because I could save some space. Please let me know either way. Thanks in advance! UPDATE: Here is the result of mount: /dev/mapper/server--vg-root on / type ext4 (rw,errors=remount-ro) proc on /proc type proc (rw,noexec,nosuid,nodev) sysfs on /sys type sysfs (rw,noexec,nosuid,nodev) none on /sys/fs/fuse/connections type fusectl (rw) none on /sys/kernel/debug type debugfs (rw) none on /sys/kernel/security type securityfs (rw) udev on /dev type devtmpfs (rw,mode=0755) devpts on /dev/pts type devpts (rw,noexec,nosuid,gid=5,mode=0620) tmpfs on /run type tmpfs (rw,noexec,nosuid,size=10%,mode=0755) none on /run/lock type tmpfs (rw,noexec,nosuid,nodev,size=5242880) none on /run/shm type tmpfs (rw,nosuid,nodev) /dev/sda1 on /boot type ext2 (rw,acl) /dev/sda1 on /media/hd2 type ext2 (rw)

    Read the article

  • Windows Server 2008 (x64): Wont boot past bios page

    - by WebSolProv
    Happy New Year, Since a month or so ago I inherited responsibility for small network administration for my sins. The domain controller (yes there is only one, and yes I know it is best practice to have two even in a small domain setup) went down overnight and I have been trying all day to get it back up and running. Unfortunately this machine also administers our entire ActiveDirectory setup: 1) It goes thru the BIOS without any errors, nothing whatsoever 2) It gets into the “select safe mode, safe mode with networking, normal” etc and if you select either of the safe mode options it loads a few files then reboots. If you select normal it just runs for a bit (doesn’t get to the windows splash screen) and then reboots again. 3) If you select windows repair, it asks for an image to repair too: however it would appear that none was taken that can be used (!!) or one is not being shown. 4) I have tried repairing the boot sector and the boot configuration using Bootrec.exe, both which it says were completed successfully but still it doesn’t work. 5) I have tried swapping the drives into another server to rule out hardware and that didn’t work either so clearly it’s the OS. 6) I have tried running chkdsk which ran fine, and also memory check which was also fine. We do have another machine on the network that was installed as a DC so when we decommission the current infrastructure but when I try and "promote" this to the lead DC then I get “you cannot modify domain or trust information because a PDC emulator cannot be contacted" so I am unable to replicare the ActiveDirectory details. If anyone can think of any direction I should follow it would be greatly appreciated, Thanks, Alex

    Read the article

  • A plugin is preventing Eclipse from starting up

    - by Mahmoud Hossam
    It just gives me a blank window, and the splash screen doesn't go away. I tried running it in a terminal, turns out it's a problematic plugin. Is there a way to disable that plugin without the GUI? There's the error log: [org.eclipse.contribution.weaving.jdt] error at org/eclipse/contribution/jdt/IsWovenTester.aj::0 class 'org.eclipse.contribution.jdt.IsWovenTester' is already woven and has not been built in reweavable mode [org.eclipse.contribution.weaving.jdt] error at org/eclipse/contribution/jdt/IsWovenTester.aj::0 class 'org.eclipse.contribution.jdt.IsWovenTester$WeavingMarker' is already woven and has not been built in reweavable mode [org.eclipse.jdt.core] warning at org/eclipse/contribution/jdt/sourceprovider/SourceTransformerAspect.aj:106::0 does not match because declaring type is org.eclipse.jdt.core.IOpenable, if match desired use target(org.eclipse.jdt.core.ICompilationUnit) [Xlint:unmatchedSuperTypeInCall] see also: org/eclipse/jdt/internal/core/SourceRefElement.java:198::0 [org.eclipse.jdt.ui] warning at org/eclipse/contribution/jdt/sourceprovider/SourceTransformerAspect.aj:106::0 does not match because declaring type is org.eclipse.jdt.core.ITypeRoot, if match desired use target(org.eclipse.jdt.core.ICompilationUnit) [Xlint:unmatchedSuperTypeInCall] see also: org/eclipse/jdt/internal/ui/javaeditor/ASTProvider.java:572::0 [org.eclipse.contribution.weaving.jdt] error at org/eclipse/contribution/jdt/sourceprovider/SourceTransformerAspect.aj::0 class 'org.eclipse.contribution.jdt.sourceprovider.SourceTransformerAspect' is already woven and has not been built in reweavable mode [org.eclipse.contribution.weaving.jdt] error at org/eclipse/contribution/jdt/cuprovider/CompilationUnitProviderAspect.aj::0 class 'org.eclipse.contribution.jdt.cuprovider.CompilationUnitProviderAspect' is already woven and has not been built in reweavable mode [ScalaPlugin] [scalaLibBundle] Found 0 bundles: LogFilter.isLoggable threw a non-fatal unchecked exception as follows: java.lang.NullPointerException at org.eclipse.core.internal.runtime.Log.isLoggable(Log.java:101) at org.eclipse.equinox.log.internal.ExtendedLogReaderServiceFactory.safeIsLoggable(ExtendedLogReaderServiceFactory.java:59) at org.eclipse.equinox.log.internal.ExtendedLogReaderServiceFactory.logPrivileged(ExtendedLogReaderServiceFactory.java:164) at org.eclipse.equinox.log.internal.ExtendedLogReaderServiceFactory.log(ExtendedLogReaderServiceFactory.java:150) at org.eclipse.equinox.log.internal.ExtendedLogServiceFactory.log(ExtendedLogServiceFactory.java:65) at org.eclipse.equinox.log.internal.ExtendedLogServiceImpl.log(ExtendedLogServiceImpl.java:87) at org.eclipse.equinox.log.internal.LoggerImpl.log(LoggerImpl.java:54) at org.eclipse.core.internal.runtime.Log.log(Log.java:60) at scala.tools.eclipse.util.DefaultLogger.warning(DefaultLogger.scala:46) at scala.tools.eclipse.ScalaPlugin$$anonfun$3.apply(ScalaPlugin.scala:131) at scala.tools.eclipse.ScalaPlugin$$anonfun$3.apply(ScalaPlugin.scala:130) at scala.Option.getOrElse(Option.scala:108) at scala.tools.eclipse.ScalaPlugin.<init>(ScalaPlugin.scala:130) at sun.reflect.NativeConstructorAccessorImpl.newInstance0(Native Method) at sun.reflect.NativeConstructorAccessorImpl.newInstance(NativeConstructorAccessorImpl.java:57) at sun.reflect.DelegatingConstructorAccessorImpl.newInstance(DelegatingConstructorAccessorImpl.java:45) at java.lang.reflect.Constructor.newInstance(Constructor.java:525) at java.lang.Class.newInstance0(Class.java:372) at java.lang.Class.newInstance(Class.java:325) at org.eclipse.osgi.framework.internal.core.AbstractBundle.loadBundleActivator(AbstractBundle.java:166) at org.eclipse.osgi.framework.internal.core.BundleContextImpl.start(BundleContextImpl.java:679) at org.eclipse.osgi.framework.internal.core.BundleHost.startWorker(BundleHost.java:381) at org.eclipse.osgi.framework.internal.core.AbstractBundle.start(AbstractBundle.java:299) at org.eclipse.osgi.framework.util.SecureAction.start(SecureAction.java:440) at org.eclipse.osgi.internal.loader.BundleLoader.setLazyTrigger(BundleLoader.java:268) at org.eclipse.core.runtime.internal.adaptor.EclipseLazyStarter.postFindLocalClass(EclipseLazyStarter.java:107) at org.eclipse.osgi.baseadaptor.loader.ClasspathManager.findLocalClass(ClasspathManager.java:462) at org.eclipse.osgi.internal.baseadaptor.DefaultClassLoader.findLocalClass(DefaultClassLoader.java:216) at org.eclipse.osgi.internal.loader.BundleLoader.findLocalClass(BundleLoader.java:400) at org.eclipse.osgi.internal.loader.BundleLoader.findClassInternal(BundleLoader.java:476) at org.eclipse.osgi.internal.loader.BundleLoader.findClass(BundleLoader.java:429) at org.eclipse.osgi.internal.loader.BundleLoader.findClass(BundleLoader.java:417) at org.eclipse.osgi.internal.baseadaptor.DefaultClassLoader.loadClass(DefaultClassLoader.java:107) at java.lang.ClassLoader.loadClass(ClassLoader.java:356) at org.eclipse.osgi.internal.loader.BundleLoader.loadClass(BundleLoader.java:345) at org.eclipse.osgi.framework.internal.core.BundleHost.loadClass(BundleHost.java:229) at org.eclipse.osgi.framework.internal.core.AbstractBundle.loadClass(AbstractBundle.java:1207) at org.eclipse.core.internal.registry.osgi.RegistryStrategyOSGI.createExecutableExtension(RegistryStrategyOSGI.java:174) at org.eclipse.core.internal.registry.ExtensionRegistry.createExecutableExtension(ExtensionRegistry.java:905) at org.eclipse.core.internal.registry.ConfigurationElement.createExecutableExtension(ConfigurationElement.java:243) at org.eclipse.core.internal.registry.ConfigurationElementHandle.createExecutableExtension(ConfigurationElementHandle.java:55) at org.eclipse.contribution.jdt.cuprovider.CompilationUnitProviderRegistry.registerProviders(CompilationUnitProviderRegistry.java:69) at org.eclipse.contribution.jdt.cuprovider.CompilationUnitProviderRegistry.getProvider(CompilationUnitProviderRegistry.java:46) at org.eclipse.contribution.jdt.cuprovider.CompilationUnitProviderAspect.ajc$inlineAccessMethod$org_eclipse_contribution_jdt_cuprovider_CompilationUnitProviderAspect$org_eclipse_contribution_jdt_cuprovider_CompilationUnitProviderRegistry$getProvider(CompilationUnitProviderAspect.aj:1) at org.eclipse.jdt.internal.core.PackageFragment.init$_aroundBody7$advice(PackageFragment.java:47) at org.eclipse.jdt.internal.core.PackageFragment.getCompilationUnit(PackageFragment.java:216) at org.eclipse.jdt.internal.core.JavaModelManager.createCompilationUnitFrom(JavaModelManager.java:962) at org.eclipse.jdt.internal.core.JavaModelManager.create(JavaModelManager.java:871) at org.eclipse.jdt.core.JavaCore.create(JavaCore.java:2622) at org.eclipse.jdt.internal.ui.javaeditor.CompilationUnitDocumentProvider.createCompilationUnit(CompilationUnitDocumentProvider.java:941) at org.eclipse.jdt.internal.ui.javaeditor.CompilationUnitDocumentProvider.createFileInfo(CompilationUnitDocumentProvider.java:974) at org.eclipse.ui.editors.text.TextFileDocumentProvider.connect(TextFileDocumentProvider.java:478) at org.eclipse.jdt.internal.ui.javaeditor.CompilationUnitDocumentProvider.connect(CompilationUnitDocumentProvider.java:1243) at org.eclipse.ui.texteditor.AbstractTextEditor.doSetInput(AbstractTextEditor.java:4213) at org.eclipse.ui.texteditor.StatusTextEditor.doSetInput(StatusTextEditor.java:237) at org.eclipse.ui.texteditor.AbstractDecoratedTextEditor.doSetInput(AbstractDecoratedTextEditor.java:1451) at org.eclipse.jdt.internal.ui.javaeditor.JavaEditor.internalDoSetInput(JavaEditor.java:2563) at org.eclipse.jdt.internal.ui.javaeditor.JavaEditor.doSetInput(JavaEditor.java:2536) at org.eclipse.jdt.internal.ui.javaeditor.CompilationUnitEditor.doSetInput(CompilationUnitEditor.java:1395) at org.eclipse.ui.texteditor.AbstractTextEditor$19.run(AbstractTextEditor.java:3200) at org.eclipse.jface.operation.ModalContext.runInCurrentThread(ModalContext.java:464) at org.eclipse.jface.operation.ModalContext.run(ModalContext.java:372) at org.eclipse.jface.window.ApplicationWindow$1.run(ApplicationWindow.java:759) at org.eclipse.swt.custom.BusyIndicator.showWhile(BusyIndicator.java:70) at org.eclipse.jface.window.ApplicationWindow.run(ApplicationWindow.java:756) at org.eclipse.ui.internal.WorkbenchWindow.run(WorkbenchWindow.java:2642) at org.eclipse.ui.texteditor.AbstractTextEditor.internalInit(AbstractTextEditor.java:3218) at org.eclipse.ui.texteditor.AbstractTextEditor.init(AbstractTextEditor.java:3245) at org.eclipse.ui.internal.EditorManager.createSite(EditorManager.java:828) at org.eclipse.ui.internal.EditorReference.createPartHelper(EditorReference.java:647) at org.eclipse.ui.internal.EditorReference.createPart(EditorReference.java:465) at org.eclipse.ui.internal.WorkbenchPartReference.getPart(WorkbenchPartReference.java:595) at org.eclipse.ui.internal.EditorAreaHelper.setVisibleEditor(EditorAreaHelper.java:271) at org.eclipse.ui.internal.EditorManager.setVisibleEditor(EditorManager.java:1459) at org.eclipse.ui.internal.EditorManager$5.runWithException(EditorManager.java:972) at org.eclipse.ui.internal.StartupThreading$StartupRunnable.run(StartupThreading.java:31) at org.eclipse.swt.widgets.RunnableLock.run(RunnableLock.java:35) at org.eclipse.swt.widgets.Synchronizer.runAsyncMessages(Synchronizer.java:135) at org.eclipse.swt.widgets.Display.runAsyncMessages(Display.java:3563) at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3212) at org.eclipse.ui.application.WorkbenchAdvisor.openWindows(WorkbenchAdvisor.java:803) at org.eclipse.ui.internal.Workbench$33.runWithException(Workbench.java:1595) at org.eclipse.ui.internal.StartupThreading$StartupRunnable.run(StartupThreading.java:31) at org.eclipse.swt.widgets.RunnableLock.run(RunnableLock.java:35) at org.eclipse.swt.widgets.Synchronizer.runAsyncMessages(Synchronizer.java:135) at org.eclipse.swt.widgets.Display.runAsyncMessages(Display.java:3563) at org.eclipse.swt.widgets.Display.readAndDispatch(Display.java:3212) at org.eclipse.ui.internal.Workbench.runUI(Workbench.java:2604) at org.eclipse.ui.internal.Workbench.access$4(Workbench.java:2494) at org.eclipse.ui.internal.Workbench$7.run(Workbench.java:674) at org.eclipse.core.databinding.observable.Realm.runWithDefault(Realm.java:332) at org.eclipse.ui.internal.Workbench.createAndRunWorkbench(Workbench.java:667) at org.eclipse.ui.PlatformUI.createAndRunWorkbench(PlatformUI.java:149) at org.eclipse.ui.internal.ide.application.IDEApplication.start(IDEApplication.java:123) at org.eclipse.equinox.internal.app.EclipseAppHandle.run(EclipseAppHandle.java:196) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.runApplication(EclipseAppLauncher.java:110) at org.eclipse.core.runtime.internal.adaptor.EclipseAppLauncher.start(EclipseAppLauncher.java:79) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:344) at org.eclipse.core.runtime.adaptor.EclipseStarter.run(EclipseStarter.java:179) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lang.reflect.Method.invoke(Method.java:601) at org.eclipse.equinox.launcher.Main.invokeFramework(Main.java:622) at org.eclipse.equinox.launcher.Main.basicRun(Main.java:577) at org.eclipse.equinox.launcher.Main.run(Main.java:1410) at org.eclipse.equinox.launcher.Main.main(Main.java:1386) [StartupDiagnostics$] startup diagnostics: previous version = 2.0.0.rc01-2_09-201111091447-ce49e0a [StartupDiagnostics$] startup diagnostics: CURRENT version = 2.0.0.rc01-2_09-201111091447-ce49e0a [ScalaPlugin] Scala compiler bundle: reference:file:plugins/org.scala-ide.scala.compiler_2.9.2.r25964-b20111108034957.jar [org.eclipse.jdt.core] warning at org/eclipse/contribution/jdt/sourceprovider/SourceTransformerAspect.aj:106::0 does not match because declaring type is org.eclipse.jdt.core.IOpenable, if match desired use target(org.eclipse.jdt.core.ICompilationUnit) [Xlint:unmatchedSuperTypeInCall] see also: org/eclipse/jdt/internal/core/LocalVariable.java:363::0 [org.eclipse.contribution.weaving.jdt] error at org/eclipse/contribution/jdt/imagedescriptor/ImageDescriptorSelectorAspect.aj::0 class 'org.eclipse.contribution.jdt.imagedescriptor.ImageDescriptorSelectorAspect' is already woven and has not been built in reweavable mode [org.eclipse.jdt.ui] warning at org/eclipse/contribution/jdt/sourceprovider/SourceTransformerAspect.aj:106::0 does not match because declaring type is org.eclipse.jdt.core.IOpenable, if match desired use target(org.eclipse.jdt.core.ICompilationUnit) [Xlint:unmatchedSuperTypeInCall] see also: org/eclipse/jdt/internal/ui/text/java/hover/JavadocHover.java:630::0 [org.eclipse.contribution.weaving.jdt] error at org/eclipse/contribution/jdt/itdawareness/ITDAwarenessAspect.aj::0 class 'org.eclipse.contribution.jdt.itdawareness.ITDAwarenessAspect' is already woven and has not been built in reweavable mode [ScalaPlugin] open Ride.java

    Read the article

  • SQL Server connection string Asynchronous Processing=true

    - by George2
    Hello everyone, I am using .Net 2.0 + SQL Server 2005 Enterprise + VSTS 2008 + C# + ADO.Net to develop ASP.Net Web application. My question is, if I am using Asynchronous Processing=true with SQL Server authentication mode (not Windows authentication mode, i.e. using sa account and password in connection string in web.config), I am wondering whether Asynchronous Processing=true will impact performance of my web application (or depends on my ADO.Net code implementation pattern/scenario)? And why? thanks in advance, George

    Read the article

  • Audio recording and playback using NAudio

    - by Egon
    When I try recording audio following this here, and using the related source code from here in the (voicerecorder.audio project), I face the problem that the recording stops within moments of starting and so does the playback. the recorded file is 46 bytes, and playback is there for less than a second, basically, the thread jumps to the next statement immediately. If I try to sleep the thread, it doesn't help. What can I do to keep it in the recording mode or playback mode until user interrupt ?

    Read the article

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >