Search Results

Search found 8189 results on 328 pages for 'fedora 16'.

Page 98/328 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >

  • Route forwarded traffic through eth0 but local traffic through tun0

    - by Ross Patterson
    I have a Ubuntu 12.04/Zentyal 2.3 server configured with WAN NATed on eth0, local interfaces eth1 and wlan0 bridged on br1 on which DHCP runs, and an OpenVPN connection on tun0. I only need the VPN for some things running on the gateway itself and I need to make sure that everything running on the gateway goes through the VPNs tun0. root:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default gw... 0.0.0.0 UG 100 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 br1 192.168.1.0 * 255.255.255.0 U 0 0 0 br1 A.B.C.0 * 255.255.255.0 U 0 0 0 eth0 root:~# ip route 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.186 root:~# ip route show table main 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.D root:~# ip route show table default default via A.B.C.1 dev eth0 How can I configure routing (or otherwise) such that all forwarded traffic for other hosts on the LAN goes through eth0 but all traffic for the gateway itself goes through the VPN on tun0? Also, since the OpenVPN client changes routing on startup/shutdown, how can I make sure that everything running on the gateway itself loses all network access if the VPN goes down and never goes out eth0.

    Read the article

  • LAN network (switch?)

    - by guywhoneedsahand
    I am working on setting up the network for a small LAN party (less than 16 people). Most of them do not have wireless cards in their rigs, so I need to set up some way for everyone to a) play LAN games and b) access the internet. The LAN party will probably take place in my basement, where I have enough space. However, the basement is not wired up with the router which is actually on the floor above. I make a cantenna a while back that can boost the wireless performance of my computer significantly. How can I use this to provide internet and LAN to guests? My hope was that I could use a switch like this http://www.newegg.com/Product/Product.aspx?Item=N82E16833181166 for the LAN - but how can I give people access to the internet? Is there such thing as a network extender / 16-port switch? Obviously, the internet performance doesn't need to be super stellar, because the games will be using LAN - so I am looking to provide some usable internet for web browsing, and very high speed LAN for games. Thanks!

    Read the article

  • How to wire 20 computers and 20 phones and 1 server into LAN?

    - by John Smith
    I have currently 3 switches Two Netgear JFS524 with 24 slots, One Belkin with 16 slots. Server DSL Internet Router. Main question is how to connect switches together, two Netgear's are next to each other, yet one is about 100 feet away and holds about 5 computer and 5 phones. If i connect them with only 1 wire will that limit bandwidth? e.g. all 23 computers will be limited to speed of one CAT5e cable? If i connect switches with 2 cables will this give speed boost? What's the ideal scenario should i just move the third switch next to other two? Will the speed of computer connected to white switch be same as computer connected to top switch? Will moving white switch right next top switch and having 16 wires comming 100 feet instead of 1 wire comming 100 feet make it faster? EDIT 1: I actually have NETGEAR ProSafe GS105 Gigabit switch its only has 4 ports in it though, you think i can have use of it in current setup? Like connect all 3 switches and server into it and keep internet router and phone server on one of the slower switches EDIT 2: Everyone mention gigabit switches, but will they do any difference with 10/100 network cards? I then have to use gigabit cards in every computer too? I could in server perhaps, but users will be 10/100

    Read the article

  • Forward all traffic through an ssh tunnel

    - by Eamorr
    I hope someone can follow this and I'll explain as best I can. I'm trying to forward all traffic from port 6999 on x.x.x.224, through an ssh tunnel, and onto port 7000 on x.x.x.218. Here is some ASCII art: |browser|-----|Squid on x.x.x.224|------|ssh tunnel|------<satellite link>-----|Squid on x.x.x.218|-----|www| 3128 6999 7000 80 When I remove the ssh tunnel, everything works fine. The idea is to turn off encryption on the ssh tunnel (to save bandwidth) and turn on maximum compression (to save more bandwidth). This is because it's a satellite link. Here's the ssh tunnel I've been using: ssh -C -f -C -o CompressionLevel=9 -o Cipher=none eamorr@172.16.1.224 -L 7000:172.16.1.224:6999 -N The trouble is, I don't know how to get data from Squid on x.x.x.224 into the ssh tunnel? Am I going about this the wrong way? Should I create an ssh tunnel on x.x.x.218? I use iptables to stop squid on x.x.x.224 from reading port 80, but to feed from port 6999 instead (i.e. via the ssh tunnel). Do I need another iptables rule? Any comments greatly appreciated. Many thanks in advance,

    Read the article

  • Linksys WAP54G v3.1 no access, power and link LED solid

    - by user142113
    I'm managing the Network of a small enterprise. A Linksys WAP54G v3.1 used to provide the WiFi network. I was called, because the device did not provide a WiFi network anymore. I first of all tried to ping the device via LAN, but there was no reaction. I've frequently reconnected the AP to the mains and always the POWER and the LINK LED keep solid, even if no network cable is connected. What I've done yet: Reset as documented: Pressed the RESET button for 10 seconds. After that I have tried to access the AP with a direct cable connection to my computer, that I've set to a static ip of 192.168.1.240, but i got no ping response on the default IP 192.168.1.245. Furthermore ipconfig reports "media disconnected". More complex reset method as described here http://bruceshankle.blogspot.de/2005/12/how-to-reset-linksys-wap54g.html as well had no effect. also tried to ping 192.168.1.1 without success Tried this method: http://www.daniweb.com/hardware-and-software/networking/threads/142437/linksys-wireless-access-point-problem#post680245 but there was no ping response when powering up. As well the tftp transfer timed out Finally tried to short pin 15 and 16 of the flash chip on the bottom side of the AP mainboard while booting to provoke a Checksum error. This should lead to the possibility to upload a firmware with tftp, as the AP stops booting and waits for a tftp connection on 192.168.1.1. But I've had no success. As well i've put pin 15 and 16 to ground while booting, also without an effect. After all that I still can't ping the AP, ipconfig still tells me "media disconnected". The POWER and LINK LED are solid. I would appreciate your answers

    Read the article

  • Repairing inconsistent pages in database

    - by Raj
    We have a SQL 2000 DB. The server crashed due to Raid array failure. Now when we run DBCC CHECKDB, we get an error that there are 27 consistency errors in 9 pages. When we run DBCC PAGE on these pages, we get this: Msg 8939, Level 16, State 106, Line 1 Table error: Object ID 1397580017, index ID 2, page (1:8404521). Test (m_freeCnt == freeCnt) failed. Values are 2 and 19. Msg 8939, Level 16, State 108, Line 1 Table error: Object ID 1397580017, index ID 2, page (1:8404521). Test (emptySlotCnt == 0) failed. Values are 1 and 0. Since the indicated index is non-clustered and is created by a unique constarint that includes 2 columns, we tried dropping and recreating the index. This resulted in the following error: CREATE UNIQUE INDEX terminated because a duplicate key was found for index ID 2. Most significant primary key is '3280'. The statement has been terminated. However running Select var_id,result_on from tests group by var_id,result_on having count(*)>1 returns 0 rows. Here is what we are planning to do: Restore a pre-server crash copy of the DB and run DBCC CHECKDB If that returns clean, then restore again with no recovery Apply all subequent TLOG backups Stop production app, take a tail log backup and apply that too Drop prod DB and rename the freshly restored DB to make it prod Start prod app Could someone please punch holes in this approach? Maybe, suggest a different approach? What we need is minimum downtime. SQL 2000 DB Size 94 GB The table that has corrupt pages has 460 Million+ rows of data Thanks for the help. Raj

    Read the article

  • Why does cpuinfo report that my frequency is slower?

    - by Avery Chan
    My machine is running off of a AMD Sempron(tm) X2 190 Processor. According the marketing copy, it should be running at around 2.5 Ghz. Why is the cpu speed being reported as something lower? Spec description (in Chinese) $ cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 16 model : 6 model name : AMD Sempron(tm) X2 190 Processor stepping : 3 microcode : 0x10000c8 cpu MHz : 800.000 cache size : 512 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm 3dnowext 3dnow constant_tsc rep_good nopl nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt npt lbrv svm_lock nrip_save bogomips : 5022.89 TLB size : 1024 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm stc 100mhzsteps hwpstate processor : 1 vendor_id : AuthenticAMD cpu family : 16 model : 6 model name : AMD Sempron(tm) X2 190 Processor stepping : 3 microcode : 0x10000c8 cpu MHz : 800.000 cache size : 512 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm 3dnowext 3dnow constant_tsc rep_good nopl nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt npt lbrv svm_lock nrip_save bogomips : 5022.82 TLB size : 1024 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm stc 100mhzsteps hwpstate

    Read the article

  • Squirrelmail receiving duplicate emails

    - by Austin
    A client of mine is experiencing issues with his email, it appears that whenever he receives email from a certain domain it comes as duplicates. Not only are they duplicates but the duplicated items have a (+) sign next to them which usually indicates an attachment. Could this be because of a forwarding issue? Here are the headers: Return-Path: <[email protected]> Received: from bigcat.centralmasswebdesign.com (root@localhost) by tarbellconstruction.com (8.13.1/8.13.1) with ESMTP id o4OFnO23003379 for <[email protected]>; Mon, 24 May 2010 11:49:24 -0400 X-ClientAddr: 72.249.26.200 Received: from mf3.spamfiltering.com (mf3.spamfiltering.com [72.249.26.200]) by bigcat.centralmasswebdesign.com (8.13.1/8.13.1) with ESMTP id o4OFnOjF005520 for <[email protected]>; Mon, 24 May 2010 11:49:24 -0400 X-Envelope-From: [email protected] X-Envelope-To: [email protected] Received: From 67-132-16-226.dia.static.qwest.net (67.132.16.226) by mf3.spamfiltering.com (MAILFOUNDRY) id 6lzIAmdLEd+oFQAw for [email protected]; Mon, 24 May 2010 15:49:23 -0000 (GMT) Received: from mail pickup service by WMA2-EXCH1.NELCO-USA.net with Microsoft SMTPSVC; Mon, 24 May 2010 11:49:18 -0400 Content-Transfer-Encoding: 7bit Importance: normal Priority: normal X-MimeOLE: Produced By Microsoft MimeOLE V6.00.3790.4325 Content-Class: urn:content-classes:message MIME-Version: 1.0 Content-Type: multipart/mixed; boundary="----_=_NextPart_001_01CAFB58.AAB268D0" Subject: weekly activity report for week ending May 22, 2010 Date: Mon, 24 May 2010 11:49:16 -0400 Message-ID: <15BCC4D99E8CBF48A2FA37A318CFF5C801209CCC@wma2-exch1.NELCO-USA.net> X-MS-Has-Attach: yes X-MS-TNEF-Correlator: Thread-Topic: weekly activity report for week ending May 22, 2010 thread-index: Acr7WKpdCelRCiocT1eBY2YN5Ma8DA== From: "Mike LeBlanc" <[email protected]> To: "Keith Berube" <[email protected]>, "Ken Tarbell" <[email protected]> X-OriginalArrivalTime: 24 May 2010 15:49:18.0361 (UTC) FILETIME=[AB546890:01CAFB58]

    Read the article

  • Email test deferred (mail transport unavailable) with ClamAV

    - by dirt
    I'm trying to set up a simple new mail server; when I send a test email to the server the email is getting hung up during delivery (user mapping is found) and the email is never found in /home/user/Maildir/new Here is my maillog after a fresh reboot and test email, there are a few warnings I am unfamiliar with. Can you please point me in the right direction? Oct 25 14:54:57 loki dovecot: master: Dovecot v2.0.9 starting up (core dumps disabled) Oct 25 14:54:58 loki postfix/postfix-script[1369]: starting the Postfix mail system Oct 25 14:54:58 loki postfix/master[1370]: daemon started -- version 2.6.6, configuration /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: request to update table btree:/etc/postfix/smtpd_scache in non-postfix directory /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: redirecting the request to postfix-owned data_directory /var/lib/postfix Oct 25 14:56:00 loki postfix/smtpd[1455]: connect from mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/smtpd[1455]: 1CF5E20A8B: client=mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/cleanup[1461]: 1CF5E20A8B: message-id= Oct 25 14:56:01 loki postfix/qmgr[1379]: 1CF5E20A8B: from=, size=1788, nrcpt=1 (queue active) Oct 25 14:56:01 loki postfix/qmgr[1379]: warning: connect to transport private/scan: No such file or directory Oct 25 14:56:01 loki postfix/error[1462]: 1CF5E20A8B: to=, orig_to=, relay=none, delay=0.18, delays=0.15/0.02/0/0.01, dsn=4.3.0, status=deferred (mail transport unavailable) Oct 25 14:56:01 loki postfix/smtpd[1455]: disconnect from mail-ob0-f180.google.com[209.85.214.180] master.cf snippets: # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - n - - smtpd submission inet n - n - - smtpd -o smtpd_tls_security_level=encrypt # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING smtps inet n - n - - smtpd -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING scan unix - - n - 16 smtp -o smtp_data_done_timeout=1200 -o smtp_send_xforward_command=yes -o disable_dns_lookups=yes 127.0.0.1:10026 inet n - n - 16 smtpd -o content_filter= -o local_recipient_maps= -o relay_recipient_maps= -o smtpd_restriction_classes= -o smtpd_client_restrictions= -o smtpd_helo_restrictions= -o smtpd_sender_restrictions= -o smtpd_recipient_restrictions=permit_mynetworks,reject -o mynetworks_style=host -o smtpd_authorized_xforward_hosts=127.0.0.0/8

    Read the article

  • kickstart ks.cfg: Where should 'url' point?

    - by Stefan Lasiewski
    I have a kickstart file (ks.cfg) on a floppy (Old style). I am trying to install CentOS 5.4. The top of my ks.cfg says this: install # Install from local cdrom or over the network. #cdrom url --url http://kickstart.example.org/pub/centos/5.4/ On the Apache server side, this command is failing with these 404s: kickstart.example.org 192.168.16.180 - - [01/Jun/2010:17:24:30 -0700] "GET /pub/centos/5.4///disc1/.discinfo HTTP/1.1" 404 314 "-" "urlgrabber/3.1.0" kickstart.example.org 192.168.16.180 - - [01/Jun/2010:17:24:43 -0700] "GET /pub/centos/5.4/repodata/repomd.xml HTTP/1.1" 404 316 "-" "urlgrabber/3.1.0 yum/3.2.22" It seems that the value of my url doesn't match the directory structure on the server. I swear this worked a few months ago. Someone else maintains the Yum repository, and they say nothing has changed. What should the value of url URL be? Should this only include the OS (/pub/centos/5.4/), or should it include the architecture (/pub/centos/5.4/os/x86_64 )? I see that Kickstart is trying to grab a file called 'repomd.xml', but why is it looking in '/pub/centos/5.4/repodata/repomd.xml', when these files actually exist at '/pub/centos/5.4/os/x86_64/repodata/repomd.xml' and other locations at '/pub/centos/5.4/*/$ARCH/repodata/repomd.xml'? I don't see this documented or explained well in the [RedHat 5 Installation Guide1]

    Read the article

  • Tomcat web application intermittent freeze

    - by tinny
    I have a Grails web application (just a standard war file) deployed on a Ubuntu 10.10 server running on tomcat 6. My database is postgresql. The problem is that every so often (once or twice a day after inactivity) when I try to log into this web application it just freezes. I can navigate to the login page but when I try and login (first time the DB is hit, might be a clue..?) the application just freezes indefinitely, no 500 response code... the browser just waits and waits. I followed the instructions detailed here because the problem described sounded the same as mine. My GC logging showed no long running GC, all sub sec. When the application freezes a jmap heap output is... using parallel threads in the new generation. using thread-local object allocation. Concurrent Mark-Sweep GC Heap Configuration: MinHeapFreeRatio = 40 MaxHeapFreeRatio = 70 MaxHeapSize = 536870912 (512.0MB) NewSize = 21757952 (20.75MB) MaxNewSize = 87228416 (83.1875MB) OldSize = 65404928 (62.375MB) NewRatio = 7 SurvivorRatio = 8 PermSize = 21757952 (20.75MB) MaxPermSize = 85983232 (82.0MB) Heap Usage: New Generation (Eden + 1 Survivor Space): capacity = 19595264 (18.6875MB) used = 11411976 (10.883308410644531MB) free = 8183288 (7.804191589355469MB) 58.23843965562291% used Eden Space: capacity = 17432576 (16.625MB) used = 9249296 (8.820816040039062MB) free = 8183280 (7.8041839599609375MB) 53.05754009046053% used From Space: capacity = 2162688 (2.0625MB) used = 2162680 (2.0624923706054688MB) free = 8 (7.62939453125E-6MB) 99.99963008996212% used To Space: capacity = 2162688 (2.0625MB) used = 0 (0.0MB) free = 2162688 (2.0625MB) 0.0% used concurrent mark-sweep generation: capacity = 101556224 (96.8515625MB) used = 83906080 (80.01907348632812MB) free = 17650144 (16.832489013671875MB) 82.62032270912317% used Perm Generation: capacity = 85983232 (82.0MB) used = 62866832 (59.95448303222656MB) free = 23116400 (22.045516967773438MB) 73.1152232100324% used Anyone know what "From Space:" is? Any ideas on further fault finding ideas? I dont have much experience with this type of fault finding.

    Read the article

  • HP Procurve 2610 intervlan routing

    - by user19039
    Can anyone tell me why inter vlan routing is working for all vlans except my newly created vlan 4/ I have an hp procurve 2610. Any help would be appreciated. I have basically this 1 switch with all unmanaged switches attached to the core. We have a second 2610 on port 28 Running configuration: ; J9085A Configuration Editor; Created on release #R.11.25 hostname "Core_HP" interface 22 speed-duplex 100-full exit ip routing snmp-server community "public" Unrestricted vlan 1 name "DEFAULT_VLAN" untagged 1-12,17-22,26-27 ip address 192.168.4.6 255.255.255.0 tagged 25 no untagged 13-16,23-24,28 exit vlan 2 name "WAN" untagged 28 ip address 10.254.254.3 255.255.255.0 exit vlan 3 name "Wireless" untagged 13-16,24 ip address 192.168.7.6 255.255.255.0 ip helper-address 192.168.4.2 tagged 27 exit vlan 35 name "guest" untagged 23 tagged 24 exit vlan 4 name "esxi" untagged 25 ip address 10.10.1.1 255.255.248.0 exit ip route 192.168.5.0 255.255.255.0 10.254.254.1 ip route 192.168.6.0 255.255.255.0 10.254.254.1 ip route 0.0.0.0 0.0.0.0 192.168.4.10 show ip route IP Route Entries Destination Gateway VLAN Type Sub-Type M etric Dist. ------------------ --------------- ---- --------- ---------- - --------- ----- 0.0.0.0/0 192.168.4.10 1 static 1 1 10.10.0.0/21 esxi 4 connected 0 0 10.254.254.0/24 WAN 2 connected 0 0 127.0.0.0/8 reject static 0 250 127.0.0.1/32 lo0 connected 0 0 192.168.4.0/24 DEFAULT_VLAN 1 connected 0 0 192.168.5.0/24 10.254.254.1 2 static 1 1 192.168.6.0/24 10.254.254.1 2 static 1 1 192.168.7.0/24 Wireless 3 connected 0 0 show ip Internet (IP) Service IP Routing : Enabled Default TTL : 64 Arp Age : 20 VLAN | IP Config IP Address Subnet Mask Prox y ARP ------------ + ---------- --------------- --------------- ---- ----- DEFAULT_VLAN | Manual 192.168.4.6 255.255.255.0 No WAN | Manual 10.254.254.3 255.255.255.0 No Wireless | Manual 192.168.7.6 255.255.255.0 No esxi | Manual 10.10.1.1 255.255.248.0 No guest | Disabled

    Read the article

  • Something very strange with network

    - by Rodnower
    Hello, I have Windows 7 and I have very strange thing with my network. Some time I was connected through wireless router and my IP was 192.168.2.103, router's IP was 192.168.2.1 and some other IP was 192.168.2.100. The last I get from page "active DHCP clients" of web interface of the router and from "wireless clients" I may to see that 192.168.2.100 not (!) belong to my MAC address. Router build by EDimax. So after that I disabled wireless function of the router and restarted it. In this time I had not ping to 192.168.2.1. Also I had not any other connection, not wireless nor cable, but (!) I still had ping to 192.168.2.100 and I not understand what this voodoo is... C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Reply from 192.168.2.100: bytes=32 time<1ms TTL=128 Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms This is what I had: C:\Users\Andrey>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : Andrey-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Wireless LAN adapter Wireless Network Connection 3: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter #2 Physical Address. . . . . . . . . : 06-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Wireless LAN adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Gigabyte GN-WS50G (mini) PCI-E WLAN Card Physical Address. . . . . . . . . : 00-1D-7D-40-61-EB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller Physical Address. . . . . . . . . : 00-1B-24-B6-09-91 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes C:\Users\Andrey>arp -a -v Interface: 127.0.0.1 --- 0x1 Internet Address Physical Address Type 224.0.0.22 static 239.255.255.250 static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-d2-8c-af invalid 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 192.168.2.1 00-0e-2e-ff-f1-f6 dynamic 192.168.2.101 00-27-19-bc-8b-9c dynamic 192.168.2.102 00-16-e6-6c-ae-d4 dynamic 192.168.2.255 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 239.255.255.250 01-00-5e-7f-ff-fa static 255.255.255.255 ff-ff-ff-ff-ff-ff static Interface: 0.0.0.0 --- 0xffffffff Internet Address Physical Address Type 224.0.0.22 01-00-5e-00-00-16 static 255.255.255.255 ff-ff-ff-ff-ff-ff static C:\Users\Andrey>route print =========================================================================== Interface List 14...06 1d 7d 40 61 eb ......Microsoft Virtual WiFi Miniport Adapter #2 13...00 1d 7d 40 61 eb ......Gigabyte GN-WS50G (mini) PCI-E WLAN Card 11...00 1b 24 b6 09 91 ......Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller 1...........................Software Loopback Interface 1 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 1 306 ::1/128 On-link 1 306 ff00::/8 On-link =========================================================================== Persistent Routes: None Only after reboot I lost ping to there: C:\Users\Andrey>ping 192.168.2.100 Pinging 192.168.2.100 with 32 bytes of data: PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. PING: transmit failed. General failure. Ping statistics for 192.168.2.100: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), So what this mysterious cache is? Thank you for ahead.

    Read the article

  • Reconfiguring, then deleting obsolete pagefile.sys from C: in one go using a batch script

    - by DanielSmedegaardBuus
    I'm trying to set up an automated script for a Windows XP installer. It's a batch script that runs on first boot after installation, and among the things I'm trying to accomplish, is removing the pagefile from C: entirely, and putting a 16-768 MB pagefile on D: instead. Here're my batch file instructions: echo === Creating new page file on D: ... cscript %windir%\system32\pagefileconfig.vbs /create /i 16 /m 768 /vo d: >nul echo. echo === Removing old page file from C: ... cscript %windir%\system32\pagefileconfig.vbs /delete /vo C: attrib -s -h c:\pagefile.sys del c:\pagefile.sys My problem is that while these are sane commands, the removal of the pagefile on C: requires me to reboot before those commands succeed.b Or, in other words — I have to first create the D: pagefile, then reboot and delete the c:\pagefile.sys file, or I'm stuck with a c:\pagefile.sys file which isn't even recognized by Windows itself (it'll just say that there's a page file on D:, and that C: has no pagefile at all). Obviously because already some pages are written to the C:\pagefile.sys file. So how would I go about accomplishing this in one go? Or, in two gos, if this is "batch scriptable" :) TIA, Daniel :) EDIT: I should probably clarify: Running those commands above are all valid, but they'll only succeed fully if I re-run the "attrib" and "del" commands at next boot. The C: pagefile is in use at the time, so I cannot delete the file it uses, and Windows itself won't remove it when I configure it to not use C: as a page file drive. Instead, it'll leave an orphaned c:\pagefile.sys file behind (which is really large). I don't necessarily need this to work in one go, registering the last two commands to run after a reboot would also be great :)

    Read the article

  • Cisco ASA5505 won't sync with NTP

    - by Martijn Heemels
    Today I noticed that the clock my Cisco ASA 5505 firewall was running about 15 minutes late, which surprised me since I've set up the NTP client. My two NTP servers 10.10.0.1 and 10.10.0.2 are virtualized Windows Server 2008 R2 domain controllers, and both have the correct time. As shown below, the ASA knows about the two servers, can ping them and seems to poll them periodically, so I suppose it can reach them both. The ASA claims its time source is NTP, however the clock is unsynchronized. Neither host is marked as synced. Result of the command: "ping 10.10.0.1" Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.10.0.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms Result of the command: "sh ntp ass" address ref clock st when poll reach delay offset disp ~10.10.0.1 .LOCL. 1 78 1024 377 0.5 643.69 17.0 ~10.10.0.2 10.10.0.1 2 190 1024 377 0.9 655.91 58.4 * master (synced), # master (unsynced), + selected, - candidate, ~ configured Result of the command: "sh ntp stat" Clock is unsynchronized, stratum 16, no reference clock nominal freq is 99.9984 Hz, actual freq is 99.9984 Hz, precision is 2**6 reference time is 00000000.00000000 (07:28:16.000 CEST Thu Feb 7 2036) clock offset is 0.0000 msec, root delay is 0.00 msec root dispersion is 0.00 msec, peer dispersion is 0.00 msec Result of the command: "sh clock detail" 10:33:23.769 CEDT Tue Jun 26 2012 Time source is NTP UTC time is: 08:33:23 UTC Tue Jun 26 2012 Summer time starts 02:00:00 CEST Sun Mar 25 2012 Summer time ends 03:00:00 CEDT Sun Oct 28 2012 I've tried the basic steps of manually setting the time and removing and adding the timeservers, to no avail. My ASA's ntp config is simply: ntp server 10.10.0.1 ntp server 10.10.0.2 Do I need to enable authentication to use a Windows NTP server? Any thoughts?

    Read the article

  • NFSv3 + ACL: mask is gone on clients

    - by Jorge Suárez de Lis
    I'm sharing a NFS folder among a user group. The default umask on the clients is 0700, and this is a problem because newly created files won't be readable/writable by another users. So, I'm using ACLs to force the umask 0770 on the shared folder, and this works OK on the server, but not on the clients. server # getfacl /export/proyectos getfacl: Eliminando «/» inicial en nombres de ruta absolutos # file: export/proyectos # owner: root # group: root user::rwx group::rwx other::r-x default:user::rwx default:group::rwx default:mask::rwx default:other::r-x server # getfacl /export/proyectos/innovacion getfacl: Eliminando «/» inicial en nombres de ruta absolutos # file: export/proyectos/innovacion # owner: root # group: proyecto-innovacion # flags: ss- user::rwx group::rwx mask::rwx other::--- default:user::rwx default:group::rwx default:mask::rwx default:other::--- As you see, the default (and also a specific on the second directory) mask ACLs are being applied. I mount the whole share on the client: 172.16.54.56:/export/proyectos on /proyectos type nfs (rw,noatime,rsize=131072,wsize=131072,acregmin=10,acl,nfsvers=3,addr=172.16.54.56) But the mask and default:mask ACLs are gone. client $ getfacl /proyectos/ getfacl: Eliminando «/» inicial en nombres de ruta absolutos # file: proyectos/ # owner: root # group: root user::rwx group::rwx other::r-x default:user::rwx default:group::rwx default:other::r-x client $ getfacl /proyectos/innovacion getfacl: Eliminando «/» inicial en nombres de ruta absolutos # file: proyectos/innovacion # owner: root # group: proyecto-innovacion # flags: ss- user::rwx group::rwx other::--- default:user::rwx default:group::rwx default:other::--- It lacks the default:mask and mask ACLs, the only ones that I've setted. So the proposed solution to enforce umask won't work for me. Why is happening this?

    Read the article

  • VNC error: "Could not connect to session bus: Failed to connect to socket"

    - by GJ
    I started a vncserver on display :1 on an ubuntu machine. When I connect to it, I get a grey X window with an error message Could not connect to session bus: Failed to connect to socket. The vnc log is: Xvnc Free Edition 4.1.1 - built Apr 9 2010 15:59:33 Copyright (C) 2002-2005 RealVNC Ltd. See http://www.realvnc.com for information on VNC. Underlying X server release 40300000, The XFree86 Project, Inc Sun Mar 20 15:33:59 2011 vncext: VNC extension running! vncext: Listening for VNC connections on port 5901 vncext: created VNC server for screen 0 error opening security policy file /etc/X11/xserver/SecurityPolicy Could not init font path element /usr/X11R6/lib/X11/fonts/Type1/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/Speedo/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/misc/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/75dpi/, removing from list! Could not init font path element /usr/X11R6/lib/X11/fonts/100dpi/, removing from list! cat: /var/run/gdm/auth-for-link2-eGnVvf/database: No such file or directory gnome-session[24880]: WARNING: Could not make bus activated clients aware of DISPLAY=:1.0 environment variable: Failed to connect to socket /tmp/dbus-FhdHHIq8jt: Connection refused gnome-session[24880]: WARNING: Could not make bus activated clients aware of GNOME_DESKTOP_SESSION_ID=this-is-deprecated environment variable: Failed to connect to socket /tmp/dbus-FhdHHIq8jt: Connection refused gnome-session[24880]: WARNING: Could not make bus activated clients aware of SESSION_MANAGER=local/dell:@/tmp/.ICE-unix/24880,unix/dell:/tmp/.ICE-unix/24880 environment variable: Failed to connect to socket /tmp/dbus-FhdHHIq8jt: Connection refused Sun Mar 20 15:34:10 2011 Connections: accepted: 0.0.0.0::51620 SConnection: Client needs protocol version 3.8 SConnection: Client requests security type VncAuth(2) VNCSConnST: Server default pixel format depth 16 (16bpp) little-endian rgb565 VNCSConnST: Client pixel format depth 16 (16bpp) little-endian rgb565 gnome-session[24880]: Gtk-CRITICAL: gtk_main_quit: assertion `main_loops != NULL' failed gnome-session[24880]: CRITICAL: dbus_g_proxy_new_for_name: assertion `connection != NULL' failed Any ideas how to fix it?

    Read the article

  • SPF record for Gmail?

    - by Chris
    I have DNS, with a SPF TXT record, configured for a domain name. The primary user of the domain name now needs to be able to send both from our SMTP servers, and also from her GMail account. I've seen all the information about adding "include:_spf.google.com" to the SPF TXT record, but, as I look into it, it appears that record is outdated. In particular, I had the user send me a test message, and note that it was: Received: from mail-la0-f50.google.com (mail-la0-f50.google.com [209.85.215.50]) However, _spf.google.com doesn't list that IP address: $ dig +short _spf.google.com txt "v=spf1 ip4:216.239.32.0/19 ip4:64.233.160.0/19 ip4:66.249.80.0/20 ip4:72.14.192.0/18 ip4:209.85.128.0/17 ip4:66.102.0.0/20 ip4:74.125.0.0/16 ip4:64.18.0.0/20 ip4:207.126.144.0/20 ip4:173.194.0.0/16 ?all" (Note that a 209.85.21*8*.0 network is listed, but not 209.85.21*5*.0.) Is there a better way to enable sending from GMail? This user sends to at least one recipient with a strict SPF policy that bounces mail not from a designated host... Many thanks!

    Read the article

  • Server 2008 NAT Internet Not Working

    - by Jack
    I'm trying to set up Routing and Remote Access on Windows Server 2008 R2, I have a network connection that I want to share the internet from to another private network. The server has two NICs which are configured as follows: External NIC (Dynamically assigned by ISP) IP:10.175.4.150 Subnet:255.255.192.0 Gateway:10.175.0.1 DNS:10.175.0.1 Internal NIC IP:172.16.254.1 Subnet:255.255.255.0 Gateway:None DNS:None I have set the external NIC to be the public interface and enabled NAT on it in the RRAS MMC and set the internal NIC to be a private interface. I have also set up the DNS forwarding or whatever it is in the NAT section. From a client (IP:172.16.254.2) I can ping the server and access files on it, when I try to browse the web with the default gateway set to the internal NIC ip I end up getting a 404 page which is returned from the ISPs default gateway. I'm guessing it's something to do with the double NAT possibly. Trying to ping the ISPs default gateway from a private network client just times out as does accessing it directly. I've disabled and reconfigured RRAS multiple times and that doesn't seem to have made a difference, so can anyone tell me what I'm doing wrong? Thanks.

    Read the article

  • Unable to get squid working for remote users

    - by Sean
    I am trying to setup squid 3.2.4, but I have not been able to get it working for remote users. Works fine locally. Unable to figure out what I am doing wrong... http_port 3128 transparent ssl-bump generate-host-certificates=on dynamic_cert_mem_cache_size=4MB cert=/usr/share/ssl-cert/myCA.pem refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . 0 20% 4320 acl localnet src 10.0.0.0/8 # RFC 1918 possible internal network acl localnet src 172.16.0.0/12 # RFC 1918 possible internal network acl localnet src 192.168.0.0/16 # RFC 1918 possible internal network acl localnet src fc00::/7 # RFC 4193 local private network range acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl CONNECT method CONNECT http_access allow manager localhost http_access deny manager http_access deny !Safe_ports http_access allow localhost http_access allow localnet http_access allow all cache deny all via off forwarded_for off header_access From deny all header_access Server deny all header_access WWW-Authenticate deny all header_access Link deny all header_access Cache-Control deny all header_access Proxy-Connection deny all header_access X-Cache deny all header_access X-Cache-Lookup deny all header_access Via deny all header_access Forwarded-For deny all header_access X-Forwarded-For deny all header_access Pragma deny all header_access Keep-Alive deny all acl ip1 localip 1.1.1.90 acl ip2 localip 1.1.1.91 acl ip3 localip 1.1.1.92 acl ip4 localip 1.1.1.93 acl ip5 localip 1.1.1.94 tcp_outgoing_address 1.1.1.90 ip1 tcp_outgoing_address 1.1.1.91 ip2 tcp_outgoing_address 1.1.1.92 ip3 tcp_outgoing_address 1.1.1.93 ip4 tcp_outgoing_address 1.1.1.94 ip5 tcp_outgoing_address 1.1.1.90

    Read the article

  • How to enable error log in lighttpd properly?

    - by Tomaszs
    I have a Centos 5 system with Lighttpd and fastcgi enabled. It does log access but does not log errors. I have Internal Server Error 500 and no info in log and when I try to open not -existing file also - no info in error log. How to enable it properly? Below is list of modules that I've enabled: server.modules = ( "mod_rewrite", "mod_redirect", "mod_alias", # "mod_access", # "mod_cml", # "mod_trigger_b4_dl", # "mod_auth", "mod_status", "mod_setenv", "mod_fastcgi", # "mod_webdav", # "mod_proxy_core", # "mod_proxy_backend_fastcgi", # "mod_proxy_backend_scgi", # "mod_proxy_backend_ajp13", # "mod_simple_vhost", # "mod_evhost", # "mod_userdir", # "mod_cgi", # "mod_compress", # "mod_ssi", # "mod_usertrack", # "mod_expire", # "mod_secdownload", # "mod_rrdtool", "mod_accesslog" ) Here are setting of debugging: ## enable debugging #debug.log-request-header = "enable" #debug.log-response-header = "enable" #debug.log-request-handling = "enable" debug.log-file-not-found = "enable" #debug.log-condition-handling = "enable" Setting of path to error and access log: ## where to send error-messages to server.errorlog = "/home/lxadmin/httpd/lighttpd/error.log" #### accesslog module accesslog.filename = "/home/lxadmin/httpd/lighttpd/ligh.log" Settings of fastcgi: fastcgi.debug = 1 fastcgi.server = ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/tmp/php.socket", "max-procs" => 12, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "2", "PHP_FCGI_MAX_REQUESTS" => "500" ) ))) And in included config file I have: server.errorlog = "/home/httpd/mywebsite.com/stats/mywebsite.com-error_log" What comes to log files: /home/httpd/mywebsite.com/stats/ -rw-r--r-- 1 apache apache 5173239 May 16 11:34 mywebsite.com-custom_log -rwxrwxrwx 1 root root 0 Mar 27 2009 mywebsite.com-error_log /home/lxadmin/httpd/lighttpd/ -rwxrwxrwx 1 apache apache 2184 Apr 22 22:59 error.log -rwxrwxrwx 1 apache apache 6088621 May 16 11:26 ligh.log I gave error logs chmod 777 for a try to check if it's the issue, but apparently it's not. So my question is: what to do to have error log enabled?

    Read the article

  • Correct way to set up office network - 8 workstations, a file server and a staging server

    - by naunu
    Our office had this old school windows 2003 domain setup, our server caught fire, and now we are looking to do it right from scratch. Here is what we need: 5 PC and 3 Mac workstations for web development, they will each have WAMP/MAMP setup on them, managed by their developers. We will have a file server for assets, and a LAMP server with an external IP for staging. Here is what we have to work with: 5 IP addresses, brand new PC file server with windows 2008 SE, D-Link DSS-16+ 16 port switch, belkin 5 port wireless router, cable modem with 4 ports. How I have it set up now (this is a temporary makeshift setup): Cable modem = LAMP server, wireless router Wireless router = Switch = All of the workstations and file server (setup as a workgroup). We have noticed our internet is very slow with us all plugged in to the switch, and the switch plugged in to the router. I am not positive, but I think it is because our router does not have NAT. We are also having problems with the MACs connection to the network drive - it keeps disconnecting. I want this done right, and we have a ~$600 budget to buy anything else we need. Does anybody have any advice for me? Should I set up a domain or workgroup?

    Read the article

  • Upgrading Redmine, activerecord-mysql2-adapter not recognized

    - by David Kaczynski
    For upgrading Redmine from 1.0.1 to 2.1.2, I need to execute the command: rake db:migrate RAILS_ENV=production However, doing so produces the following error: rake aborted! Please install the mysql2 adapter: gem install activerecord-mysql2-adapter (mysql2 is not part of the bundle. Add it to Gemfile.) I have ran gem install activerecord-mysql2-adapter, but I still get the same error when I try to run the rake ... command. How do I get my RoR app to recognize that I have the mysql2 adapter installed already? or Is there something wrong with my activerecord-mysql2-adapter installation? Results of sudo bundle install: Using rake (10.0.0) Using i18n (0.6.1) Using multi_json (1.3.7) Using activesupport (3.2.8) Using builder (3.0.0) Using activemodel (3.2.8) Using erubis (2.7.0) Using journey (1.0.4) Using rack (1.4.1) Using rack-cache (1.2) Using rack-test (0.6.2) Using hike (1.2.1) Using tilt (1.3.3) Using sprockets (2.1.3) Using actionpack (3.2.8) Using mime-types (1.19) Using polyglot (0.3.3) Using treetop (1.4.12) Using mail (2.4.4) Using actionmailer (3.2.8) Using arel (3.0.2) Using tzinfo (0.3.35) Using activerecord (3.2.8) Using activeresource (3.2.8) Using coderay (1.0.8) Using fastercsv (1.5.5) Using rack-ssl (1.3.2) Using json (1.7.5) Using rdoc (3.12) Using thor (0.16.0) Using railties (3.2.8) Using jquery-rails (2.0.3) Using metaclass (0.0.1) Using mocha (0.12.3) Using mysql (2.8.1) Using net-ldap (0.3.1) Using pg (0.14.1) Using ruby-openid (2.1.8) Using rack-openid (1.3.1) Using bundler (1.2.1) Using rails (3.2.8) Using rmagick (2.13.1) Using shoulda (2.11.3) Using sqlite3 (1.3.6) Using yard (0.8.3) [32mYour bundle is complete! Use `bundle show [gemname]` to see where a bundled gem is installed.[0m Results of sudo find / -name "*mysql2*": /var/lib/gems/1.8/doc/mysql2-0.3.11 /var/lib/gems/1.8/doc/activerecord-3.2.9/ri/ActiveRecord/Base/mysql2_connection-c.ri /var/lib/gems/1.8/doc/activerecord-mysql2-adapter-0.0.3 /var/lib/gems/1.8/doc/activerecord-mysql2-adapter-0.0.3/ri/ActiveRecord/Base/em_mysql2_connection-c.ri /var/lib/gems/1.8/doc/activerecord-mysql2-adapter-0.0.3/ri/ActiveRecord/Base/mysql2_connection-c.ri /var/lib/gems/1.8/gems/mysql2-0.3.11 /var/lib/gems/1.8/gems/mysql2-0.3.11/spec/mysql2 /var/lib/gems/1.8/gems/mysql2-0.3.11/mysql2.gemspec /var/lib/gems/1.8/gems/mysql2-0.3.11/lib/mysql2.rb /var/lib/gems/1.8/gems/mysql2-0.3.11/lib/mysql2 /var/lib/gems/1.8/gems/mysql2-0.3.11/lib/mysql2/mysql2.so /var/lib/gems/1.8/gems/mysql2-0.3.11/ext/mysql2 /var/lib/gems/1.8/gems/mysql2-0.3.11/ext/mysql2/mysql2.so /var/lib/gems/1.8/gems/mysql2-0.3.11/ext/mysql2/mysql2_ext.c /var/lib/gems/1.8/gems/mysql2-0.3.11/ext/mysql2/mysql2_ext.h /var/lib/gems/1.8/gems/mysql2-0.3.11/ext/mysql2/mysql2_ext.o /var/lib/gems/1.8/gems/activerecord-3.2.9/lib/active_record/connection_adapters/mysql2_adapter.rb /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3 /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/activerecord-mysql2-adapter.gemspec /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/lib/arel/engines/sql/compilers/mysql2_compiler.rb /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/lib/activerecord-mysql2-adapter.rb /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/lib/activerecord-mysql2-adapter /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/lib/active_record/connection_adapters/em_mysql2_adapter.rb /var/lib/gems/1.8/gems/activerecord-mysql2-adapter-0.0.3/lib/active_record/connection_adapters/mysql2_adapter.rb /var/lib/gems/1.8/gems/activerecord-3.2.8/lib/active_record/connection_adapters/mysql2_adapter.rb /var/lib/gems/1.8/cache/mysql2-0.3.11.gem /var/lib/gems/1.8/cache/activerecord-mysql2-adapter-0.0.3.gem /var/lib/gems/1.8/specifications/activerecord-mysql2-adapter-0.0.3.gemspec /var/lib/gems/1.8/specifications/mysql2-0.3.11.gemspec Contents of /usr/share/redmine/Gemfile: source 'http://rubygems.org' gem 'rails', '3.2.8' gem "jquery-rails", "~> 2.0.2" gem "i18n", "~> 0.6.0" gem "coderay", "~> 1.0.6" gem "fastercsv", "~> 1.5.0", :platforms => [:mri_18, :mingw_18, :jruby] gem "builder", "3.0.0" # Optional gem for LDAP authentication group :ldap do gem "net-ldap", "~> 0.3.1" end # Optional gem for OpenID authentication group :openid do gem "ruby-openid", "~> 2.1.4", :require => "openid" gem "rack-openid" end # Optional gem for exporting the gantt to a PNG file, not supported with jruby platforms :mri, :mingw do group :rmagick do # RMagick 2 supports ruby 1.9 # RMagick 1 would be fine for ruby 1.8 but Bundler does not support # different requirements for the same gem on different platforms gem "rmagick", ">= 2.0.0" end end # Database gems platforms :mri, :mingw do group :postgresql do gem "pg", ">= 0.11.0" end group :sqlite do gem "sqlite3" end end platforms :mri_18, :mingw_18 do group :mysql do gem "mysql" end end platforms :mri_19, :mingw_19 do group :mysql do gem "mysql2", "~> 0.3.11" end end platforms :jruby do gem "jruby-openssl" group :mysql do gem "activerecord-jdbcmysql-adapter" end group :postgresql do gem "activerecord-jdbcpostgresql-adapter" end group :sqlite do gem "activerecord-jdbcsqlite3-adapter" end end group :development do gem "rdoc", ">= 2.4.2" gem "yard" end group :test do gem "shoulda", "~> 2.11" # Shoulda does not work nice on Ruby 1.9.3 and seems to need test-unit explicitely. gem "test-unit", :platforms => [:mri_19] gem "mocha", "0.12.3" end local_gemfile = File.join(File.dirname(__FILE__), "Gemfile.local") if File.exists?(local_gemfile) puts "Loading Gemfile.local ..." if $DEBUG # `ruby -d` or `bundle -v` instance_eval File.read(local_gemfile) end # Load plugins' Gemfiles Dir.glob File.expand_path("../plugins/*/Gemfile", __FILE__) do |file| puts "Loading #{file} ..." if $DEBUG # `ruby -d` or `bundle -v` instance_eval File.read(file) end Contents of /usr/share/redmine/Gemfile.lock: GEM remote: http://rubygems.org/ specs: actionmailer (3.2.8) actionpack (= 3.2.8) mail (~> 2.4.4) actionpack (3.2.8) activemodel (= 3.2.8) activesupport (= 3.2.8) builder (~> 3.0.0) erubis (~> 2.7.0) journey (~> 1.0.4) rack (~> 1.4.0) rack-cache (~> 1.2) rack-test (~> 0.6.1) sprockets (~> 2.1.3) activemodel (3.2.8) activesupport (= 3.2.8) builder (~> 3.0.0) activerecord (3.2.8) activemodel (= 3.2.8) activesupport (= 3.2.8) arel (~> 3.0.2) tzinfo (~> 0.3.29) activeresource (3.2.8) activemodel (= 3.2.8) activesupport (= 3.2.8) activesupport (3.2.8) i18n (~> 0.6) multi_json (~> 1.0) arel (3.0.2) builder (3.0.0) coderay (1.0.8) erubis (2.7.0) fastercsv (1.5.5) hike (1.2.1) i18n (0.6.1) journey (1.0.4) jquery-rails (2.0.3) railties (>= 3.1.0, < 5.0) thor (~> 0.14) json (1.7.5) mail (2.4.4) i18n (>= 0.4.0) mime-types (~> 1.16) treetop (~> 1.4.8) metaclass (0.0.1) mime-types (1.19) mocha (0.12.3) metaclass (~> 0.0.1) multi_json (1.3.7) mysql (2.8.1) mysql2 (0.3.11) net-ldap (0.3.1) pg (0.14.1) polyglot (0.3.3) rack (1.4.1) rack-cache (1.2) rack (>= 0.4) rack-openid (1.3.1) rack (>= 1.1.0) ruby-openid (>= 2.1.8) rack-ssl (1.3.2) rack rack-test (0.6.2) rack (>= 1.0) rails (3.2.8) actionmailer (= 3.2.8) actionpack (= 3.2.8) activerecord (= 3.2.8) activeresource (= 3.2.8) activesupport (= 3.2.8) bundler (~> 1.0) railties (= 3.2.8) railties (3.2.8) actionpack (= 3.2.8) activesupport (= 3.2.8) rack-ssl (~> 1.3.2) rake (>= 0.8.7) rdoc (~> 3.4) thor (>= 0.14.6, < 2.0) rake (10.0.0) rdoc (3.12) json (~> 1.4) rmagick (2.13.1) ruby-openid (2.1.8) shoulda (2.11.3) sprockets (2.1.3) hike (~> 1.2) rack (~> 1.0) tilt (~> 1.1, != 1.3.0) sqlite3 (1.3.6) test-unit (2.5.2) thor (0.16.0) tilt (1.3.3) treetop (1.4.12) polyglot polyglot (>= 0.3.1) tzinfo (0.3.35) yard (0.8.3) PLATFORMS ruby DEPENDENCIES activerecord-jdbcmysql-adapter activerecord-jdbcpostgresql-adapter activerecord-jdbcsqlite3-adapter builder (= 3.0.0) coderay (~> 1.0.6) fastercsv (~> 1.5.0) i18n (~> 0.6.0) jquery-rails (~> 2.0.2) jruby-openssl mocha (= 0.12.3) mysql mysql2 (~> 0.3.11) net-ldap (~> 0.3.1) pg (>= 0.11.0) rack-openid rails (= 3.2.8) rdoc (>= 2.4.2) rmagick (>= 2.0.0) ruby-openid (~> 2.1.4) shoulda (~> 2.11) sqlite3 test-unit yard Results of gem list: actionmailer (3.2.9, 3.2.8) actionpack (3.2.9, 3.2.8) activemodel (3.2.9, 3.2.8) activerecord (3.2.9, 3.2.8) activerecord-mysql2-adapter (0.0.3) activeresource (3.2.9, 3.2.8) activesupport (3.2.9, 3.2.8) arel (3.0.2) builder (3.0.0) bundler (1.2.1) coderay (1.0.8) erubis (2.7.0) fastercsv (1.5.5) hike (1.2.1) i18n (0.6.1) journey (1.0.4) jquery-rails (2.0.3) json (1.7.5) mail (2.4.4) metaclass (0.0.1) mime-types (1.19) mocha (0.12.3) multi_json (1.3.7) mysql (2.8.1) mysql2 (0.3.11) net-ldap (0.3.1) pg (0.14.1) polyglot (0.3.3) rack (1.4.1) rack-cache (1.2) rack-openid (1.3.1) rack-ssl (1.3.2) rack-test (0.6.2) rails (3.2.9, 3.2.8) railties (3.2.9, 3.2.8) rake (10.0.0) rdoc (3.12) rmagick (2.13.1) ruby-openid (2.1.8) shoulda (2.11.3) sprockets (2.2.1, 2.1.3) sqlite3 (1.3.6) thor (0.16.0) tilt (1.3.3) treetop (1.4.12) tzinfo (0.3.35) yard (0.8.3) Results of 'bundle show`: Gems included by the bundle: * actionmailer (3.2.8) * actionpack (3.2.8) * activemodel (3.2.8) * activerecord (3.2.8) * activeresource (3.2.8) * activesupport (3.2.8) * arel (3.0.2) * builder (3.0.0) * bundler (1.2.1) * coderay (1.0.8) * erubis (2.7.0) * fastercsv (1.5.5) * hike (1.2.1) * i18n (0.6.1) * journey (1.0.4) * jquery-rails (2.0.3) * json (1.7.5) * mail (2.4.4) * metaclass (0.0.1) * mime-types (1.19) * mocha (0.12.3) * multi_json (1.3.7) * mysql (2.8.1) * net-ldap (0.3.1) * pg (0.14.1) * polyglot (0.3.3) * rack (1.4.1) * rack-cache (1.2) * rack-openid (1.3.1) * rack-ssl (1.3.2) * rack-test (0.6.2) * rails (3.2.8) * railties (3.2.8) * rake (10.0.0) * rdoc (3.12) * rmagick (2.13.1) * ruby-openid (2.1.8) * shoulda (2.11.3) * sprockets (2.1.3) * sqlite3 (1.3.6) * thor (0.16.0) * tilt (1.3.3) * treetop (1.4.12) * tzinfo (0.3.35) * yard (0.8.3)

    Read the article

  • Where is my CPU usage going?

    - by Josh
    My Ubuntu 10.04 Lucid virtual machine is saying it's at 100% CPU usage... but all I'm running is Thunderbird. According to top, CPU usage should be ~25.9%... How do I interpret this conflicting output from top? top - 13:55:26 up 3:35, 4 users, load average: 3.03, 2.59, 2.48 Tasks: 178 total, 1 running, 177 sleeping, 0 stopped, 0 zombie Cpu(s): 16.0%us, 79.7%sy, 0.0%ni, 0.0%id, 0.0%wa, 1.3%hi, 3.0%si, 0.0%st Mem: 509364k total, 479108k used, 30256k free, 3092k buffers Swap: 2096440k total, 58380k used, 2038060k free, 225116k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 7708 jnet 20 0 480m 109m 17m S 18.4 22.1 21:59.14 thunderbird-bin 4615 jnet 20 0 5488 1268 1040 S 2.3 0.2 5:00.03 nx-rootless-ses 7124 jnet 20 0 56688 27m 4812 S 2.0 5.5 6:35.09 nxagent 6724 nx 20 0 9628 1400 636 S 1.6 0.3 3:26.59 sshd 30106 root 20 0 2544 1236 908 R 0.7 0.2 0:00.33 top 19 root 20 0 0 0 0 S 0.3 0.0 0:22.45 ata/0 38 root 20 0 0 0 0 S 0.3 0.0 0:05.53 scsi_eh_1 345 root 20 0 0 0 0 S 0.3 0.0 0:04.72 kjournald 1719 root 20 0 3260 1192 944 S 0.3 0.2 0:17.36 vmware-guestd 1 root 20 0 2804 1356 940 S 0.0 0.3 0:01.99 init 2 root 20 0 0 0 0 S 0.0 0.0 0:00.01 kthreadd 3 root RT 0 0 0 0 S 0.0 0.0 0:00.00 migration/0 4 root 20 0 0 0 0 S 0.0 0.0 0:00.15 ksoftirqd/0 5 root RT 0 0 0 0 S 0.0 0.0 0:00.00 watchdog/0 ... Specifically I'm referring to the fact that the CPU usage totals show 0% idle time: Cpu(s): 16.0%us, 79.7%sy, 0.0%ni, 0.0%id, 0.0%wa, 1.3%hi, 3.0%si, 0.0%st Yet when adding up the percentages in the %CPU column I get 25.9%, not 100%!

    Read the article

  • apache with php fastcgi keeps going down

    - by Josh Nankin
    I have an apache2 server configured with MPM worker and php fast cgi. Lately the apache logs have been telling me that MaxClients is being reached frequently, even though it's already pretty high. My server is now constantly going down, and I see a bunch of lines like this in the log: [Sun Mar 06 04:25:40 2011] [error] [client 50.16.83.115] FastCGI: comm with (dynamic) server "/var/local/fcgi/php-cgi-wrapper.fcgi" aborted: (first read) idle timeout (20 sec) [Sun Mar 06 04:25:40 2011] [error] [client 50.16.83.115] FastCGI: incomplete headers (0 bytes) received from server "/var/local/fcgi/php-cgi-wrapper.fcgi" I can see that my php-cgi processes are pretty large (about 70mb on average). Here's my apache configuration for MPM worker: KeepAlive ON KeepAliveTimeout 2 <IfModule mpm_worker_module> StartServers 5 MinSpareThreads 10 MaxSpareThreads 10 ThreadLimit 64 ThreadsPerChild 10 MaxClients 20 MaxRequestsPerChild 2000 </IfModule> Heres my fastcgi apache configuration: <IfModule mod_fastcgi.c> # One shared PHP-managed fastcgi for all sites Alias /fcgi /var/local/fcgi # IMPORTANT: without this we get more than one instance # of our wrapper, which itself spawns 20 PHP processes, so # that would be Bad (tm) FastCgiConfig -idle-timeout 20 -maxClassProcesses 1 <Directory /var/local/fcgi> # Use the + so we don't clobber other options that # may be needed. You might want FollowSymLinks here Options +ExecCGI </Directory> AddType application/x-httpd-php5 .php AddHandler fastcgi-script .fcgi Action application/x-httpd-php5 /fcgi/php-cgi-wrapper.fcgi </IfModule> Here's my fastcgi wrapper: #!/bin/sh PHPRC="/etc/php5/apache2" export PHPRC PHP_FCGI_CHILDREN=8 export PHP_FCGI_CHILDREN exec /usr/bin/php-cgi Any help would be very very much appreciated!

    Read the article

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >