Search Results

Search found 2803 results on 113 pages for 'manca weeks'.

Page 98/113 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >

• Is my Cisco switch port bad?

  - by ewwhite

  I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

  Read the article

• A dusty server room

  - by pauska

  Here's the story.. The owners of the building we lease office space from decided to do a renovation of the exterior. This involved in some pretty heavy work at the level where our server room is, including exchanging windows wich are fit inside a concrete wall. My red alert went off when I heard that they were going to do the same thing with our server room (yes, our server room has a window. We're a small shop with 3 racks. The window is secured with steel bars.) I explicity told the contractor that they need to put up a temporarily wall between our racks and the original wall - and to make sure that the temporary wall is 100 % air and water-tight. They promised to do so. The temporary wall has a small door in it, so that workers can go in/out through the day (through our server room, wich was the only option....). On several occasions I could find the small door half-way shut while working evenings/nights. I locked the door, and thought that they would hopefully get the point soon and keep the door shut. I even gave a electrician a mouthful when I saw that he didn't close the door properly. By this point - I bet that most of you get a picture of what happened. Yes, they probably left the door open while drilling in the concrete. I present you our 4 weeks old EMC VNX: I'll even put in a little bonus, here is the APC UPS one rack further away from the temporary wall. See the nice little landing strip from my finger? What should I do? The only thing that comes to mind is to either call all our suppliers (EMC, HP, Dell, Cisco) and get them to send technicians to check out all the gear in the server room, or get some kind of certified 3rd-party consulant to check all of it. Would you run production systems on this gear? How long? Edit: I should also note that our aircondition isn't exactly enterprise-grade, given the nature of our small room. It's just a single inverter, wich have failed one time before I started working here (failed inverters usually leads to water dripping out).

  Read the article

• Good maintained privacy Add-On/settings set that takes usability into account?

  - by Foo Bar

  For some weeks I've been trying to find a good set of Firefox Addons that give me a good portion of privacy/security without losing to much of usability. But I can't seem to find a nice combination of add-ons/settings that I'm happy with. Here's what I tried, together with the pros and cons that I discovered: HTTPS Everywhere: Has only pro's: just install and be happy (no interaction needed), loads known pages SLL-encrypted, is updated fairly often NoScript - Fine, but needs a lot of fine-tuning, often maintained, mainly blocks all non-HTML/CSS Content, but the author sometimes seems to do "untrustworthy" decission RequestPolicy - seems dead (last activity 6 months ago, has some annoying bugs, official support mail address is dead), but the purpose of this is really great: gives you full control over cross-site requests: blocks by default, let's you add sites to a whitelist, once this is done it works interaction-less in the background AdBlock Edge: blocks specific cross-site requests from a pre-defined whitelist (can never be fully sure, need to trust others) Disconnect: like AdBlock Edge, just looking different, has no interaction possibilities (can never be fully sure, need to trust others, can not interact even if I wanted to) Firefox own Cookie Managment (block by default, whitelist specific sites), after building own whitelist it does it's work in the background and I have full control All These addons together basically block everything unsecure. But there are a lot of redundancies: NoScript has a mixed-content blocker, but FF has it's own for a while now. Also the Cookie blocker from NoScript is reduntant to my FF-Cookie setting. NoScript also has an XSS-blocker, which is redundant to RequestPolicy. Disconnect and AdBlock are extremly redundant, but not fully. And there are some bugs (especially RequestPolicy). And RequestPolicy seems to be dead. All in all, this list is great but has these heavy drawbacks. My favourite set would be "NoScript Light" (only script blocking, without all the additonal redundant-to-other-addons hick-hack it does) + HTTPS Everywhere + RequestPolicy-clone (maintained, less buggy), because RequestPolicy makes all other "site-blockers" obsolete (because it blocks everything by default and let's me create a whitelist). But since RequestPolicy is buggy and seems to be dead I have to fallback to AdBlock Edge and Disconnect, which don't block all and and need more maintaining (whitelist updates, trust-check). Are there addons that fulfill my wishes?

  Read the article

• Anyone else experiencing high rates of Linux server crashes during a leap second day?

  - by Bron Gondwana

  POSTMORTEM Anticlimax: only thing that died was my VPN (openvpn) link to the cluster, so there was an exciting few seconds while it re-established. Everything else was fine. Starting back ntp everywhere. If you look at Marco's blog at http://my.opera.com/marcomarongiu/blog/2012/06/01/an-humble-attempt-to-work-around-the-leap-second - he has a solution for phasing the time change over 24 hours using ntpd -x to avoid the 1 second skip. Give that a go if it matters to you. For the systems I run, the jump isn't a problem. Just today, Sat June 30th - starting soon after the start of the day GMT. We've had a handful of blades in different datacentres as managed by different teams all go dark - not responding to pings, screen blank. They're all running Debian Squeeze - with everything from stock kernel to custom 3.2.21 builds. Most are Dell M610 blades, but I've also just lost a Dell R510 and other departments have lost machines from other vendors too. There was also an older IBM x3550 which crashed and which I thought might be unrelated, but now I'm wondering. The one crash which I did get a screen dump from said: [3161000.864001] BUG: spinlock lockup on CPU#1, ntpd/3358 [3161000.864001] lock: ffff88083fc0d740, .magic: dead4ead, .owner: imapd/24737, .owner_cpu: 0 Unfortunately the blades all supposedly had kdump configured, but they died so hard that kdump didn't trigger - and they had console blanking turned on. I've disabled console blanking now, so fingers crossed I'll have more information after the next crash. Just want to know if it's a common thread or "just us". It's really odd that they're different units in different datacentres bought at different times and run by different admins (I run the FastMail.FM ones)... and now even different vendor hardware. Most of the machines which crashed had been up for weeks/months and were running 3.1 or 3.2 series kernels. The most recent crash was a machine which had only been up about 6 hours running 3.2.21. THE WORKAROUND Ok people, here's how I worked around it. disabled ntp: /etc/init.d/ntp stop created http://linux.brong.fastmail.fm/2012-06-30/fixtime.pl (code stolen from Marco, see blog posts in comments) ran fixtime.pl without an argument to see that there was a leap second set ran fixtime.pl with an argument to remove the leap second NOTE: depends on adjtimex. I've put a copy of the squeeze adjtimex binary at http://linux.brong.fastmail.fm/2012-06-30/adjtimex - it will run without dependencies on a squeeze 64 bit system. If you put it in the same directory as fixtime.pl, it will be used if the system one isn't present. Obviously if you don't have squeeze 64 bit... find your own. I'm going to start ntp again tomorrow. As an anonymous user suggested - an alternative to running adjtimex is to just set the time yourself, which will presumably also clear the leapsecond counter.

  Read the article

• DNS NS and domain clarification

  - by thejartender

  I am really trying to get my home web server up and I don't seem to be succeeding. My web server withing my host system is running my web application and is viewable at the current isp ip 88.89.190.171 over WAN indicating that the webapp is fine and that router ports are forwarded. I have set up a DNS on this system with a single name server in the network and I manage to ping it with ping ns.thejarbar.org I have registered this private name server at my current hosting provider. My domain (thejarbar.org) is obviously registered and I have pointed it to my name server. My question here is if it is simply a matter of waiting on propagation for me to be able to ping my domain? Another way of asking this is if the fact that my name server is discoverable indicates that I have set it up correctly to be used? I have tested with dig and dig -x on my host and have A records for the name server. The server is not the Authorative server so I am concerned that this may be the reason why my site is not discoverable. Is there anything else I may need to so still? I only have one ns. currently, but should this succeed I will be purchasing a more stable secondary system to host my development applications. This is my best chance at getting work (freelance development) due to illness) and this I feel is the last step I need to succeed. Please note that this is temporarily a home server and I will most likely be using it as part of a professional setup very soon I will likely have to repeat this question therefore in a prefessional context in a few weeks as nothing will be different other than the fact that I am going to have a server running elsewhere. I am using bind9 and Ubuntu 12.10 and my records are: $TTL 3D @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 10.0.0.42 @ IN NS ns.thejarbar,org. yuccalaptop IN A 10.0.0.19 ns IN A 10.0.0.42 gw IN A 10.0.0.138 www IN CNAME thejarbar.org. $TTL 3D 0.0.10.in-addr.arpa. IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); 0.0.10.in-addr.arpa. IN NS ns.thejarbar.org. 42 IN PTR thejarbar.org. 19 IN PTR yuccalaptop.thejarbar.org. 138 IN PTR gw.thejarbar.org. My localhost IP is 10.0.0.42 I wish for this to be my host and name server.

  Read the article

• Is DHCP lease expriring years from now okay?

  - by sharptooth

  I'm reviewing Azure web role logs and there's output from ipconfig /all IPv4 Address. . . . . . . . . . . : 10.61.145.37(Preferred) . Subnet Mask . . . . . . . . . . . : 255.255.254.0. Lease Obtained. . . . . . . . . . : Monday, September 24, 2012 12:26:00 PM. Lease Expires . . . . . . . . . . : Thursday, October 31, 2148 6:55:12 PM. you see, the lease expires in year 2148 but my VM will likely not run for more than one month - when I deploy the new version of my code I first deploy it to new VMs, then switch traffic, then release the new VMs. In general such usage pattern is normal - VMs typically live from several dozen minutes to several weeks on Azure. I suspect the lease that long will cause problems on the internal Azure network sooner or later. Is such long DHCP lease okay or is it likely a misconfiguration?

  Read the article

• resolve access violation exception (0xC0000005) crashing IIS app pool

  - by Joseph

  IIS 7.5, server 2008 r2, classic asp and asp .net 2.0, 3.5 website same server, same app pool. The past 4 weeks thousands of these errors 'C0000005' are occurring. I know from IIS debug diag tool that 'C0000005' is an access violation error. Below is the top line from my debug diag report. In w3wp__PID__6656__Date__01_08_2011__Time_01_42_46AM__281__First Chance Access Violation.dmp the assembly instruction at asp!CActiveScriptEngine::GetApplication+27 in \\?\C:\Windows\System32\inetsrv\asp.dll from Microsoft Corporation has caused an access violation exception (0xC0000005) when trying to read from memory location 0x00000000 on thread 29 Thread 29 - System ID 6736 Entry point 0x00000000 Create time 1/8/2011 12:46:26 AM Time spent in user mode 0 Days 00:00:00.140 Time spent in kernel mode 0 Days 00:00:00.078 Function Source asp!CActiveScriptEngine::GetApplication+27 vbscript!COleScript::GetDebugApplicationCoreNoRef+2b vbscript!COleScript::FDebuggerEnabled+30 vbscript!COleScript::SetScriptSite+cd asp!CActiveScriptEngine::Init+125 asp!CScriptManager::GetEngine+252 asp!AllocAndLoadEngines+28f asp!ExecuteGlobal+17a asp!Execute+b5 asp!CHitObj::ViperAsyncCallback+3fc asp!CViperAsyncRequest::OnCall+6a comsvcs!CSTAActivityWork::STAActivityWorkHelper+32 ole32!EnterForCallback+f4 ole32!SwitchForCallback+1a8 ole32!PerformCallback+a3 ole32!CObjectContext::InternalContextCallback+15b ole32!CObjectContext::DoCallback+1c comsvcs!CSTAActivityWork::DoWork+12f comsvcs!CSTAThread::DoWork+18 comsvcs!CSTAThread::ProcessQueueWork+37 comsvcs!CSTAThread::WorkerLoop+135 msvcrt!_endthreadex+44 msvcrt!_endthreadex+ce kernel32!BaseThreadInitThunk+e ntdll!__RtlUserThreadStart+70 ntdll!_RtlUserThreadStart+1b BELOW is the faulting module. ASP report Executing ASP requests 0 Request(s) ASP templates cached 0 Template(s) ASP template cache size 0.00 Bytes Loaded ASP applications 1 Application(s) ASP.DLL Version 7.5.7600.16620 ASP application report ASP application metabase key Physical Path Virtual Root Session Count 0 Session(s) Request Count 0 Request(s) Session Timeout 0 minutes(s) Path to Global.asa Server side script debugging enabled False Client side script debugging enabled False Out of process COM servers allowed False Session state turned on False Write buffering turned on False Application restart enabled False Parent paths enabled False ASP Script error messages will be sent to browser False ASP!CACTIVESCRIPTENGINE::GETAPPLICATION+27In w3wp__PID__6656__Date__01_08_2011__Time_01_42_46AM__281__First Chance Access Violation.dmp the assembly instruction at asp!CActiveScriptEngine::GetApplication+27 in \\?\C:\Windows\System32\inetsrv\asp.dll from Microsoft Corporation has caused an access violation exception (0xC0000005) when trying to read from memory location 0x00000000 on thread 29 recent events: server was being brute forced by hackers all of Dec and probably earlier, they weren't able to gain access but did get a virus on and blasted out spam. insatlled AVG and about the 17 or 22 latest patches. after that the app pool started crashing and the server has crashed a couple times since then. I am in no mans land as I am a developer and not a sys admin but I have to assume many roles. So I'm reaching out for help. Sometimes I will see hundreds of these 'C0000005' scriptengine errors in the event log in a matter of seconds and other times just a few times an hour. I googled this line 'ASP!CACTIVESCRIPTENGINE::GETAPPLICATION' and got nothing. Its like the function don't exist or something. I have spent many hours google-ing to no avail and am now turning to the experts on the forums. Thank you for your help

  Read the article

• WiFi signal is lost every 3 minutes

  - by Software Monkey

  For several weeks now my Android phone has been losing it's WiFi signal momentarily, typically at about 3 minute intervals (about 3 minutes, 1.5 seconds) and occasionally at some longer interval that always seems to be just over 3 minutes. This causes an interruption of several seconds while the WiFi connection is re-established and typically fails any kind of download/streaming that is happening, makes web sites "unreachable" and generally makes the phone unusable as a data device due to the frequency. The signal remains down for about a second, but the phone takes a few more seconds to reconnect to the router. This happens regardless of proximity to the router, which otherwise show a very strong signal - usually -40 to -30 dBm or better in the same room, nowhere less than 060 dBm anywhere in the house. Changing channels does not help (I've tried 1, 4, 8 and 9). Nor does turning off the router's guest access. Nor does turning off the 5.0 GHz band. Monitoring the signal on my phone with WiFi analyzer, shows all WiFi signals on all channels drop to nothing when the WiFi connection is lost (there are two other networks on different channels which are strong enough to be relevant, with about 6 others constantly fading in and out). WiFi analyzer shows 3 separate signals for my router, the main 2.4 GHz, the guest 2.4 GHz and the 5.0 GHz. Using WiFi Analyzer on my wife's phone side-by-side shows no change in signal when my phone drops, nor does her phone drop. Monitoring the signal using our laptop, side-by-side likewise shows no signal loss and likewise the laptop does not lose it's WiFi connection. But, at work, the phone seems to not exhibit the same behavior, or, if it does, it's very occasional. Monitoring it all day at work I only saw the signal drop 3 or 4 times. The signal strength of the various networks there is comparatively weak. AT&T were super helpful: "Sorry, we can't help you with WiFi problems. You could try doing a factory reset on your phone". </sarcasm The router is relatively new, but has been working fine with this phone since last Dec. Phone : Motorola Atrix (about 8 months old). Router : Belkin N750 DB (F9K1103 v1 (01C)). Router Firmware: 1.00.46 (2011/10/28 6:37:11). Security : WPA/WPA2-Personal (PSK)

  Read the article

• Gigabyte GA-Z77X-D3H MB problems

  - by Hans

  I installed a new system last week. I've some issues with it. The system consists of a: Gigabyte GA-Z77X-D3H with F9 BIOS (latest) Intel Core i5 3570K proccesor Sapphire Radeon HD7850 2x 8GB Corsair 1600MHz memory OCZ Vertex 2 120G SSD Connected peripherals : 2 Samsung 940BF (1 via DVI on GFX card, 1 via an Displayport to DVI adapter) 1 Dell U2312HM monitor (displayport) Dell USB Hub (monitor) Wired mouse, wireless keyboard (logitech) Logitch G25 wheel Canon MP800 printer Okay, my issues are the following: if I plug in 1 or more monitor at DisplayPort during boot, most of the time it won't boot properly. I get an empty message screen of UEFI: only the header GIGABYTE DUEL BIOS appears. The system reboots itself, turns on for a few seconds (no video) and then reboots again. Now it starts all over again. This repeats until I remove all displayport monitors. Windows boots, and I can use them when I replug them. The graphics card has been running fine for a few weeks on an older system (intel Q6600). Another issue is; if I plug in my G25 steering wheel, the UEFI BIOS is inaccessible. It either gives the same empty UEFI screen, or the BIOS screen is rendering but crashes half way (so pieces of text and graphics are missing, and it has crashed). If I remove the G25, all is fine. To verify the graphics card is OK and the motherboard is causing these issues, I tried an NVIDIA 8800GT graphics card. This hasn't got Displayport, but it also cannot boot the BIOS with the G25 wheel plugged in. The PC also refuses to go into or out of standby. It just hangs when going into standby, and in other occasions (when it does succesfully do so) get out of standby. Power supply is OCZ StealthXStream 600W. Proccesor is 25 - 30C idle, ~55C stressed (Scythe Mugen 2). I am really puzzled what can be done to resolve this. I am not really waiting for an RMA request (otherwise I will return the MB for another type), because it will likely mean I have to wait very long before I get a replacement. Anyone else with a similar experience on this board/chipset or can help me troubleshoot this?

  Read the article

• Vista stuck at "Shutting down..." screen. Any way to get verbose logging?

  - by CapBBeard

  Hi all, My home machine has been running fine for about 3 years, no problems at all. Within the last couple of weeks it's had real trouble trying to shut down. It'll get so far and then just sit there at the "Shutting down..." screen for hours. I've left it overnight, I've tried in safe mode, all to no avail. These days, I just wait for the disk activity to finish up and then hold the power button to turn it off. Feels dirty as, especially because there's a RAID involved! The hardware itself is in pretty good shape and of decent spec; Core 2 Quad, 4GB RAM, 1TB RAID 1+0, so it's not quite like a 7 year old PC coming to end of life! In the last month, hardware hasn't changed except for a new monitor. Admittedly I haven't tried unplugging the monitor but I've never heard of that preventing a shutdown. I might give it a whirl later I guess, as a last resort. I've uninstalled old apps, done updates, checked the event log, looked in device manager, uninstalled all non-present devices, disabled various non-critical devices (imaging, audio etc), unplugged peripherals, stopped non-essential services, unplugged the network, disabled the network adapter entirely, ran chkdsk, verified my RAID, the list goes on. But not a single lead. I'm pretty stumped. It could be hardware, but I have no other evidence to suggest so; when the PC is running, it runs fine. Temperatures are good, gaming is smooth as always, disk performance is fine. Event log even makes it look like the shutdown was completed (gets to the point where the event log service stops). In fact, the PC doesn't appear to realise that I cut the power to it. So my question is, does anyone know if there is a way I can get some verbose output (or a log) from shutdown to give me some idea of what is causing the issue? I'm guessing it's stuck unloading some app/driver but it would be good to get some specifics! Unless anyone has any other ideas? I suspect a reinstall would resolve the issue, however I'm looking to get a new PC built in the next month or so, and the reinstall is going to be quite a big job so I'd rather just wait until then if it comes to that. Would still be nice to get this sorted in the mean time though. Cheers!

  Read the article

• Windows7 issue in mutli- tasking and memory

  - by Nitesh

  I seeming some problem in my windows OS recently, let me first say my system configuration. processor - Intel(R) Core(TM)2 Quad CPU Q8400 @ 2.66 GHz Installed memory (RAM) - 4.00 GB (3.00 GB usable) System type - 32 bit operating system I am using two OS in this system, first one is Windows7 and the other is centOS. Well, I am using this from a long time there was no problem , and all of a sudden since from couple weeks I am facing problems in my Windows7 OS. In windows7 i was nearing using multiple jobs almost every time i log in, there was no problem but now i don't no what happen I am not able to do multiple jobs at same time. For example- 1 I am now not able to listen to music in windows media player and view photo's. All of a sudden the system stops working and does not respond and then respond after 5mins and the music get played where it got stopped after 5 mins. 2 When i start browersing internet it hangs all of sudden and doesn't respond for 2 or 3 mins and gets loading. I mean it just happens for every operation i do in the system. Even now typing was also difficult, it gets hanged very frequently even though i am doing single task. I have never come across this kind of problem before. So the first thing i did was to see the useage of the processor and the memory. Well, i thick the useage of the processor was fine, for single task the useage was some where around 3 to 5%. Well, it was something weird i found in the memory, in spite of no task that i was running it was using somewhere around 34 to 41% of memory. So i opened the task manager and click on resource monitor in performance tab. And in the memory section of the monitoring tool i found the usage of my RAM, it was something like this. Hardware reserved - 1029 MB In Use - 1430 MB Modified - 49 MB Standby - 1566 MB free - 22 MB And i could also see Available 1588 MB Cached 1615 MB Total 3067 MB Installed 4096 MB well, this if all i could find out and i have no idea why my computer is acting so weird all of a sudden and the performance problem is growing day by day and i also don't know if there is problem in Bios, i have let it for default settings from long time. please help me and Thank you in advance for reading this and helping me.

  Read the article

• Windows Server 2008 R2 loses ability to connect to network share

  - by JamesB

  I could sure use some help with this one: I've got two Windows Server 2008 R2 x64 Terminal Servers, as well as several 2003 servers (DNS / Wins / AD / DC). On the two 2008 boxes, every now and then they will get in this mode where you can't map a drive to a random server. I say random server because it's not always the same server that you can't map to. Here is a summary of what I can and can't do: net view \\servername Sometimes this works, sometimes it does not. net view \\FQDN This always works. net view \\IPAddress This always works. ping servername Sometimes this works, sometimes it does not. ping FQDN This always works. ping IPAddress This always works. I've been looking all over for a solution to this. It sure seems like Microsoft would have a hotfix by now. The kicker to this is that it sometimes works great, especially after a reboot. It may run for 2 weeks just fine, but all of a sudden it will fail to resolve the remote server name. It will then be this way for a few days, then it might start working again. Also, while it's in the mode of not working, the other servers have no problem getting there. It's just these 2008 R2 Terminal Servers. Setting a static entry in the Hosts file and LMHosts does not make it work. All servers have static IPs and they are registered in DNS and Wins just fine. Here is a long thread on MS Technet of the exact same problem, but they don't have a good solution. Here is their workaround (It was from June of 2010): Good news - a hotfix is in the works and a workaround has been identified: Root cause is that since this is SMB1 all user sessions are on a single TCP connection to the remote server. The first user to initiate a connection to the remote SMB server has their logon-ID added to the structure defining the connection. If that user logs off all subsequent uses of that TCP session fail as the logon-id is no longer valid. As a workaround for now to keep the issue from happening you will want to have the user not logoff the Terminal Server only disconnect their sessions. Any word from anyone out there about a solution? Any help would sure be appreciated. Thanks, James

  Read the article

• High CPU usage - symptoms moving from server to server after bouncing

  - by grt3kl

  First off, I apologize if I didn't include enough information to properly troubleshoot this issue. This sort of thing isn't my specialty, so it is a learning process. If there's something I need to provide, please let me know and I'll be happy to do what I can. The images associated with my question are at the bottom of this post. We are dealing with a clustered environment of four WebLogic 9.2 Java application servers. The cluster utilizes a round-robin load algorithm. Other details include: Java(TM) 2 Runtime Environment, Standard Edition (build 1.5.0_12-b04) BEA JRockit(R) (build R27.4.0-90_CR352234-91983-1.5.0_12-20071115-1605-linux-x86_64, compiled mode) Basically, I started looking at the servers' performance because our customers are seeing lots of lag at various times of the day. Our servers should easily handle the loads they are given, so it's not clear what's going on. Using HP Performance Manager, I generated some graphs that indicate that the CPU usage is completely out of whack. It seems that, at any given point, one or more of the servers has a CPU utilization of over 50%. I know this isn't particularly high, but I would say it is a red flag based on the CPU utilization of the other servers in the WebLogic cluster. Interesting things to note: The high CPU utilization was occurring only on server02 for several weeks. The server crashed (extremely rare; we are not sure if it's related to this) and upon starting it back up, the CPU utilization was normal on all 4 servers. We restarted all 4 managed servers and the application server (on server01) yesterday, on 2/28. As you can see, server03 and server04 picked up the behavior that was seen on server02 before. The CPU utilization is a Java process owned by the application user (appown). The number of transactions is consistent across all servers. It doesn't seem like any one server is actually handling more than another. If anyone has any ideas or can at least point me in the right direction, that would be great. Again, please let me know if there is any additional information I should post. Thanks!

  Read the article

• Alternative Windows Offline Files + Windows Backup + Previous Version Setup

  - by Herson

  Currently our documents are all hosted in a Windows 7 box. Users can access the files using Windows share and the documents are available offline (windows 7 feature). The documents are being backed up daily by Windows 7 backup and restore utility. Users can access previous versions of the file (from the backups) using Windows Explorer "previous versions" feature. This setup is currently working well, except for the following: We would prefer to have access to hourly versions of the file, not daily. The previous version mechanism is tied up to the backup mechanism. Windows 7 performs a full backup every week and incremental backup everyday. The previous versions of a file is actually what are the available in the backups. If you 20GB documents and want to maintain at least three(3) year history, you will use at minimum 3 years * 52 weeks * 20GB or about 3TB even if there are few changes in the documents. Its pretty inefficient use of space. Looking up previous versions of a file is very slow (tens of minutes). This is probably related to the previous issue - Windows has to traverse its all of its backups. I am considering using SVN + autocommit/autoupdate tortoisesvn. It will have the following advantages: Backups are easy and will also backup the whole history of each documents. (Just backup the repository). Creating previous versions can be frequent. I think svn commit / update can be done every two minutes or so. Users can sync over the net. However, I can see the following issues: More conflicts than the original setup because both multiple users can now edit the same file even both are online, i.e. can connect to the SVN repo. The users can off course lock the file first before editing, but that would mean they have to adjust. Delay on propagation of file changes. On windows 7 file sharing, changes made by one online user will be instantaneously available to other online users. With the SVN setup, changes will only be propagated when the users execute the svn add/commit/update sequence. Delay will be probably a few minutes. This workflow will no longer work: "Hi, I just edited document X, can you have a quick look?" I would like to ask the opinion of the community for alternative setups, or improvements on the above setups to work out the kinks.

  Read the article

• Complete machine freezes...at a loss

  - by user28818

  Guys, We built around 12 machines a few months ago to run Ubuntu. They each have the following specs: ASUS Z8NA-D6 motherboard Dual quad core Intel(R) Xeon(R) CPU E5520 @ 2.27GHz OCZ Mod Extreme Pro 500W power supply 12 GB Kingston RAM Nvidia GeForce 9800 GT graphics card My machine ran well for awhile. However, it started experiencing random lockups. These lockups are not X lockups, they are complete system freezes. The nic stops responding, the magic sysrq buttons won't work. The machine is dead. I first suspected RAM. Memtest86 didn't find anything, but I replaced the RAM anyway. Still, lockups. So I replaced the graphics card. Still, more lockups. They became more and more frequent and started to happen 2-3 times a day. So I replaced the motherboard and power supply in one fell swoop. Suddenly, no more lockups! Woohoo! Except, a week later, in the morning, the machine wouldn't wake up. I reset it, started it up, and the log files showed the last entry at around 11 pm the evening before. This has started occurring with more frequency...now just about every morning I come in, the machine is locked up, and has been since the night before. Yesterday, in the 3 weeks since I replaced the motherboard and power supply, the machine actually locked up on in in mid-work. This is the first time since replacing the two (MB and PS) that this happened while I was using it. All others occurred while I was away. I'm at a loss. Nothing is in syslog or message that would indicate a problem around the time of the lockup. Temps are good...I use lmsensors to monitor and have a script that writes the output to file every minute. They never get that high. The only thing I haven't replaced at this point is the case and the harddrives. I doubt either could be the cause. What would you do if you were in my shoes? Is there a troubleshooting approach I'm missing? For the record, all of the other machines, all eleven of them, don't have any problems. They're all running the same version of Ubuntu (Lucid) that I am. Thanks!

  Read the article

• Will spreading your servers load not just consume more recourses

  - by Saif Bechan

  I am running a heavy real-time updating website. The amount of recourses needed per user are quite high, ill give you an example. Setup Every visit The application is php/mysql so on every visit static and dynamic content is loaded. Recourses: apache,php,mysql Every second (no more than a second will just be too long) The website needs to be updated real-time so every second there is an ajax call thats updates the website. Recourses: jQuery,apache,php,mysql Avarage spending for single user (spending one minute and visited 3 pages) Apache: +/- 63 requests / responsess serving static and dynamic content (img,css,js,html) php: +/- 63 requests / responses mysql: +/- 63 requests / responses jquery: +/- 60 requests / responses Optimization I want to optimize this process, but I think that maybe it would be just the same in the end. Before implementing and testing (which will take weeks) I wanted to have some second opinions from you guys. Every visit I want to start off with having nginx in the front and work as a proxy to deliver the static content. Recources: Dynamic: apache,php,mysql Static: nginx This will spread the load on apache a lot. Every Second For the script that loads every second I want to set up Node.js server side javascript with nginx in te front. I want to set it up that jquery makes a request ones a minute, and node.js streams the data to the client every second. Recources: jQuery,nginx,node.js,mysql Avarage spending for single user (spending one minute and visited 3 pages) Nginx: 4 requests / responsess serving mostly static conetent(img,css,js) Apache: 3 requests only the pages php: 3 requests only the pages node.js: 1 request / 60 responses jquery: 1 request / 60 responses mysql: 63 requests / responses Optimization As you can see in the optimisation the load from Apache and PHP are lifted and places on nginx and node.js. These are known for there light footprint and good performance. But I am having my doubts, because there are still 2 programs extra loaded in the memory and they consume cpu. So it it better to have less programs that do the job, or more. Before I am going to spend a lot of time setting this up I would like to know if it will be worth the while.

  Read the article

• How do you backup 40+ Centos5.5 servers?

  - by John Little

  We are embarrassed to ask this question. Apologies for our lack of UNIX expertise. We have inherited 40+ centos 5.5 servers, and don't know how to back them up. We need low level clone type images so that we could restore the servers from scratch if we had to replace the HDs etc. We have used the "dd" command, but we assume this only works if you want to back up one local disk to another, not 40 servers to one server with an external USB HD attached. All 40 servers have a pair of mirrored disks (dont know if its HW or SW raid). Most only have 100MB used. SErvers are running apache, zend, tomcat, mysql etc. Ideally we dont want to have to shut them down to backup (but could). We assume that standard unix commands like tar, cpio, rsync, scp etc. are of no use as they only copy files, not partitions, all attributes, groups etc. i.e. do not produce a result which can simply be re-imaged to a new HD to get the serer back from dead. We have a large SAN, a spare windows box and spare unix boxes, but these are only visible to one layer in the network. We have an unused Dell DL2000 monster tape unit, but no sw or documentation for it. WE have a copy of symantec backup exec, but we have no budget for unix client licenses. (The company has negative amounts of money). We need to be able to initiate the backup remotely, as we can only access the servers in person in an emergency (i.e. to restore) Googling returns some applications to do this, e.g. clonezilla - looks difficult to install and invasive. Mondo, only seems to support backup if you are local to the machine. Amanda might be an option, but looks like days/weeks of work to learn and setup? Is there anything built into Centos, or do we have to go the route of installing, learning and configuring a set of backup softwares? Any ideas? This must be a pretty standard problem which goggling doesnt give an obvious answer.

  Read the article

• D-Link DIR-300 slows down / loses network

  - by basic6

  there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

  Read the article

• MongoDB and datasets that don't fit in RAM no matter how hard you shove

  - by sysadmin1138

  This is very system dependent, but chances are near certain we'll scale past some arbitrary cliff and get into Real Trouble. I'm curious what kind of rules-of-thumb exist for a good RAM to Disk-space ratio. We're planning our next round of systems, and need to make some choices regarding RAM, SSDs, and how much of each the new nodes will get. But now for some performance details! During normal workflow of a single project-run, MongoDB is hit with a very high percentage of writes (70-80%). Once the second stage of the processing pipeline hits, it's extremely high read as it needs to deduplicate records identified in the first half of processing. This is the workflow for which "keep your working set in RAM" is made for, and we're designing around that assumption. The entire dataset is continually hit with random queries from end-user derived sources; though the frequency is irregular, the size is usually pretty small (groups of 10 documents). Since this is user-facing, the replies need to be under the "bored-now" threshold of 3 seconds. This access pattern is much less likely to be in cache, so will be very likely to incur disk hits. A secondary processing workflow is high read of previous processing runs that may be days, weeks, or even months old, and is run infrequently but still needs to be zippy. Up to 100% of the documents in the previous processing run will be accessed. No amount of cache-warming can help with this, I suspect. Finished document sizes vary widely, but the median size is about 8K. The high-read portion of the normal project processing strongly suggests the use of Replicas to help distribute the Read traffic. I have read elsewhere that a 1:10 RAM-GB to HD-GB is a good rule-of-thumb for slow disks, As we are seriously considering using much faster SSDs, I'd like to know if there is a similar rule of thumb for fast disks. I know we're using Mongo in a way where cache-everything really isn't going to fly, which is why I'm looking at ways to engineer a system that can survive such usage. The entire dataset will likely be most of a TB within half a year and keep growing.

  Read the article

• Mac OSX 10.8 Server DNS Domain Routing

  - by Oldek

  I just cant seem to figure out the logic in how to configure my Mac Server. So I have set up an DNS, which will take the domain and all subdomains and point towards an IP. File: db.mydomain.com (in /var/named/) mydomain.com. 10800 IN SOA mydomain.com. admin.mydomain.com. ( 2012110903 ; serial 3600 ; refresh (1 hour) 900 ; retry (15 minutes) 1209600 ; expire (2 weeks) 86400 ; minimum (1 day) ) 10800 IN NS mydomain.com. 10800 IN A 10.0.1.2 www.mydomain.com. 10800 IN A 10.0.1.2 So I want all of these requests to be requested to the 10.0.1.2 server, as I run 2 servers in my cluster. This one has always handled the requests, and now I want to add a server in between. So the server in between will get all the signals from my router which NAT the trafic coming from outside. So after setting this up and trying to point my port 80 towards my new server which will be the middle point, it doesn't work. Is it even possible to do it this way? First server: Mac Second server: Linux So what I try to achieve once more: 1. User goes to mydomain.com or www.mydomain.com 2. User request gets handled by my first server 3. First server refers to a local server, which is only available locally (it is configured to allow requests on port 80 and handle them) 4. Second server receives signal 5. Second server returns a request (either directly send to user or send through first server, whichever is most secure and configurable) I also want to be able to set up domains that lead to other servers in the future, and some that are only available within the VPN. (If that changes anything) I hope some kind soul could help me with this, it is really cumbersome for my mind to get the logic here. Do I have to configure my other server in any way? /Marcus

  Read the article

• BlueScreens on my ThinkPad with Windows 7 64 Bit and a SSD (CRITICAL_OBJECT_TERMINATION, ntoskernel.exe)

  - by pvorb

  I'm getting BlueScreens about every five days for more than three months. Here's an example: A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntoskrnl.exe CRITICAL_OBJECT_TERMINATION If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x000000f4 (0x0000000000000003, 0xfffffa80065f2b30, 0xfffffa80065f2e10, 0xfffff80002f9bf40) *** ntoskrnl.exe - Address 0xfffff80002c98d00 base at 0xfffff80002c19000 DateStamp 0x4d9fdd5b It's has always been the same BlueScreen message showing CRITICAL_OBJECT_TERMINATION, 0x000000f4, and ntoskrnl.exe. Of course the addresses change. My computer is a ThinkPad T400 (about 2 years old) with a SSD in it. I'm also running Windows 7 Professional 64 bit. When I bought my computer, it had a 250GByte SeaGate HDD in it, which I replaced by a 500GByte HDD by Western Digital. Last september I bought a Corsair F120 SSD and replaced the HDD by this SSD. Then I bought a LEICKE HDD adapter for the UltraBay II where I plugged in my 500GByte HDD. This configuration ran about half a year without any errors. After re-installing Windows this spring, I am getting regular BlueScreens. Sometimes my system runs for about 2 weeks without a BSOD, sometimes I get several BlueScreens a day. The only thing that I noticed is, that I'm always running Google Chrome when it happens. Is there anyone who has made his/her own bad experiences whith some of my components or is there anybody who can tell me if it would be helpful to send my notebook to Lenovo? Thank you very much for your help on my issue! Regards, Paul

  Read the article

• Switching efficiently between windows, not apps, in OS X

  - by Vultan

  Previous questions have asked "how can I efficiently switch between windows, not applications, in OS X"? (Switching windows on OS X, Switch between windows on Mac OS X? and others). The most recommended suggestions seem to be: Use some combo of cmd-tab and cmd-~. Use Expose, and possibly Spaces Use Witch I spent the money on Witch, and have been using it for a few weeks; it's ok, but it is sometimes slow to respond, sometimes buggy on window order, crashes my system if I disable and re-enable it too many times, and doesn't work properly with X11 apps. The built-in cmd-tab and cmd-~ are ok, but still bring an entire application to the forefront. I find a very common workflow I use is to bounce back and forth between two windows (for example, a browser window and a Thunderbird email in progress), when both apps (the browser and email software) have multiple windows open. I can use Cmd-Tab to get back and forth between apps, but whenever I switch to an app, ALL windows from that app pop up. That suddenly fills my screen with irrelevant data and windows, and often drops those other windows in front of the single window from the other app that I was using and would conveniently like to keep viewing even though it isn't in focus. Expose seems to be the preferred "OS X natural way," but I can't seem to get myself to use it efficiently. I hit F9, and see 10 windows; I then need to squint, try to find the window I want, then use the mouse or the cursor keys to navigate to the one I want. Given the number of power users who say they use Expose, I must be missing the boat here. My goal is not to make this a repeat of previous questions. I'm not asking "what are my alternatives?" (unless I've missed one above!) Rather, I'm asking: what are you, OS X power users, actually doing to handle the use case I described above? Another common use case for me is having multiple Excel spreadsheets open and multiple browser windows open, and I'm rapidly switching back and forth between one spreadsheet in particular and one browser window. Every time I Cmd-Tab, all spreadsheets or all browser windows appear: I don't want to see the ones I'm not working with, and they tend to hide the windows from the alternative app that I don't have in focus but I'd like to at least eyeball. Can you describe what your workflow is like, and how you rapidly and thoughtlessly switch between windows from apps that have multiple windows open?

  Read the article

• Wireless Network suddenly cant connect after Windows update

  - by vinir

  UPDATE: As my patience started to end, the laptop started to display symptoms of other malfunctions, so I ended up returning it to Asus and actually had the price of the laptop back in store credit. I did not solve the problem per se, but as I don't have the notebook and the screen, the keyboard, the touchpad and other parts were malfunctioning, I can safely assume that it was put to rest. I don't know how to behave when my question isn't actually answered, but was "solved", so I placed this over here. Anyone that knows how to end this topic, I would appreciate the heads up. Thanks for everything, everyone, it's nice to see that this topic in the community was active even when all this time had passed. vinir So I bought an ASUS K43E notebook earlier this year and built a wireless conection to link it to. It worked great for the first weeks, but then I updated my Windows 7 Home Basic with the daily updates; After that my home network couldn't be reached no matter what I did. I have linux on dual boot on the same notebook and it can connect to my home wireless network flawlessly. I have a hunch that it's somehow related to the Network Profile settings. I have noticed my network was set as "Home network", but after the system updates I got changed to "Public". Now I can't connect to it to change the profile settings. My Atheros Network adapter is updated to the latest driver (march 2012), and I still can't connect. The funny thing is that the same thing happened to my mother's notebook, as it has the same Network Adapter, Atheros AR9285, as I recall it. I managed to fix it on my mother's computer by using an specific network LSP and profiling reset that was available through her notebook's antivirus program, avast! Internet Security. I can't get that to work on my notebook, but I suspect that some related tool might just make it work too. So the question is: how to modify a network's profile and settings that were stored in my notebook? I can't connect to the specific network on Windows, as stated before.

  Read the article

• Internet Pings but Does Not Load

  - by t3techcom18

  From what I've been seeing and been doing my research for the past two days, many people have been having the same issues throughout the years, however, this is the first time I've encountered this issue and many of the specific workarounds or fixes have not worked for me. I've been trying to work through this for 24 hours straight now, but to no avail so many thanks to those that can help. On Monday night, got home from work; surfing the internet for half an hour, everything was fine as always. Just after half an hour, my Internet got very sluggish and then it died completely. I thought it might have been the an update I just put through in terms of Windows Update that said was a critical update for MSE, as the same thing happened a few years ago. I did a System Restore to two different dates that were in the past two weeks, nothing. Uninstalled MSE and disabled Windows Defender and the Windows Firewall: Nothing. Reset IE Options, Reset Winsock, Dumping DNS, many of the other command prompt screens to reset items: Nothing. Reset the modem: Nothing. What DID work, however, was a ping test to Yahoo. The ping test worked, saying all four packets was recieved, yet nothing else popped up. LAN and CenturyLink said everything worked on their end and that everything was connected properly, as well as the speeds working fine. CenturyLink said in their notes that they thought Port 80 was blocked. I went and put in the Firewall to allow Port 80 but it didn't make any difference whatsoever. I remembered I had a spare modem laying around and I switched them up, both modem and the cords - nothing. I then hooked it up to my netbook to see if that would work, as it usually does - connection didn't work there either. Like I said, it's been about 24 hours now and this is increasingly frustrating, as I've tried all solutions (While browsing through 10 search results pages on my phone) suggested and still nothing. Any suggestions and tricks would be greatly appreciated! Here's my specs: Windows 7 32-bit Home Premium Intel Core 2 Duo 3.14 Ghz 4 GB Kingston DDR2 RAM eVGA nForce 750i SLI eVGA GeForce GTX 560 Ti FPB ISP: CenturyLink No router Modem: CenturyLink 660 Series Hardwired connection PLEASE NOTE: This is the only computer I have (Like I said, the netbook solution didn't work), so downloading programs and such is not an option til I get to other computers somewhere else, like right now. Unless someone knows of a way of copying/pasting a file in Windows and then transferring said info to an Android smartphone, this is gunna take a while haha. Patience is requested.

  Read the article

• New MySQL Cluster 7.3 Previews: Foreign Keys, NoSQL Node.js API and Auto-Tuned Clusters

  - by Mat Keep

  At this weeks MySQL Connect conference, Oracle previewed an exciting new wave of developments for MySQL Cluster, further extending its simplicity and flexibility by expanding the range of use-cases, adding new NoSQL options, and automating configuration. What’s new: Development Release 1: MySQL Cluster 7.3 with Foreign Keys Early Access “Labs” Preview: MySQL Cluster NoSQL API for Node.js Early Access “Labs” Preview: MySQL Cluster GUI-Based Auto-Installer In this blog, I'll introduce you to the features being previewed. Review the blogs listed below for more detail on each of the specific features discussed. Save the date!: A live webinar is scheduled for Thursday 25th October at 0900 Pacific Time / 1600UTC where we will discuss each of these enhancements in more detail. Registration will be open soon and published to the MySQL webinars page MySQL Cluster 7.3: Development Release 1 The first MySQL Cluster 7.3 Development Milestone Release (DMR) previews Foreign Keys, bringing powerful new functionality to MySQL Cluster while eliminating development complexity. Foreign Key support has been one of the most requested enhancements to MySQL Cluster – enabling users to simplify their data models and application logic – while extending the range of use-cases for both custom projects requiring referential integrity and packaged applications, such as eCommerce, CRM, CMS, etc. Implementation The Foreign Key functionality is implemented directly within the MySQL Cluster data nodes, allowing any client API accessing the cluster to benefit from them – whether they are SQL or one of the NoSQL interfaces (Memcached, C++, Java, JPA, HTTP/REST or the new Node.js API - discussed later.) The core referential actions defined in the SQL:2003 standard are implemented: CASCADE RESTRICT NO ACTION SET NULL In addition, the MySQL Cluster implementation supports the online adding and dropping of Foreign Keys, ensuring the Cluster continues to serve both read and write requests during the operation.  This represents a further enhancement to MySQL Cluster's support for on0line schema changes, ie adding and dropping indexes, adding columns, etc.  Read this blog for a demonstration of using Foreign Keys with MySQL Cluster.  Getting Started with MySQL Cluster 7.3 DMR1: Users can download either the source or binary and evaluate the MySQL Cluster 7.3 DMR with Foreign Keys now! (Select the Development Release tab). MySQL Cluster NoSQL API for Node.js Node.js is hot! In a little over 3 years, it has become one of the most popular environments for developing next generation web, cloud, mobile and social applications. Bringing JavaScript from the browser to the server, the design goal of Node.js is to build new real-time applications supporting millions of client connections, serviced by a single CPU core. Making it simple to further extend the flexibility and power of Node.js to the database layer, we are previewing the Node.js Javascript API for MySQL Cluster as an Early Access release, available for download now from http://labs.mysql.com/. Select the following build: MySQL-Cluster-NoSQL-Connector-for-Node-js Alternatively, you can clone the project at the MySQL GitHub page.  Implemented as a module for the V8 engine, the new API provides Node.js with a native, asynchronous JavaScript interface that can be used to both query and receive results sets directly from MySQL Cluster, without transformations to SQL. Figure 1: MySQL Cluster NoSQL API for Node.js enables end-to-end JavaScript development Rather than just presenting a simple interface to the database, the Node.js module integrates the MySQL Cluster native API library directly within the web application itself, enabling developers to seamlessly couple their high performance, distributed applications with a high performance, distributed, persistence layer delivering 99.999% availability. The new Node.js API joins a rich array of NoSQL interfaces available for MySQL Cluster. Whichever API is chosen for an application, SQL and NoSQL can be used concurrently across the same data set, providing the ultimate in developer flexibility.  Get started with MySQL Cluster NoSQL API for Node.js tutorial MySQL Cluster GUI-Based Auto-Installer Compatible with both MySQL Cluster 7.2 and 7.3, the Auto-Installer makes it simple for DevOps teams to quickly configure and provision highly optimized MySQL Cluster deployments – whether on-premise or in the cloud. Implemented with a standard HTML GUI and Python-based web server back-end, the Auto-Installer intelligently configures MySQL Cluster based on application requirements and auto-discovered hardware resources Figure 2: Automated Tuning and Configuration of MySQL Cluster Developed by the same engineering team responsible for the MySQL Cluster database, the installer provides standardized configurations that make it simple, quick and easy to build stable and high performance clustered environments. The auto-installer is previewed as an Early Access release, available for download now from http://labs.mysql.com/, by selecting the MySQL-Cluster-Auto-Installer build. You can read more about getting started with the MySQL Cluster auto-installer here. Watch the YouTube video for a demonstration of using the MySQL Cluster auto-installer Getting Started with MySQL Cluster If you are new to MySQL Cluster, the Getting Started guide will walk you through installing an evaluation cluster on a singe host (these guides reflect MySQL Cluster 7.2, but apply equally well to 7.3 and the Early Access previews). Or use the new MySQL Cluster Auto-Installer! Download the Guide to Scaling Web Databases with MySQL Cluster (to learn more about its architecture, design and ideal use-cases). Post any questions to the MySQL Cluster forum where our Engineering team and the MySQL Cluster community will attempt to assist you. Post any bugs you find to the MySQL bug tracking system (select MySQL Cluster from the Category drop-down menu) And if you have any feedback, please post them to the Comments section here or in the blogs referenced in this article. Summary MySQL Cluster 7.2 is the GA, production-ready release of MySQL Cluster. The first Development Release of MySQL Cluster 7.3 and the Early Access previews give you the opportunity to preview and evaluate future developments in the MySQL Cluster database, and we are very excited to be able to share that with you. Let us know how you get along with MySQL Cluster 7.3, and other features that you want to see in future releases, by using the comments of this blog.

  Read the article

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >