Search Results

Search found 12899 results on 516 pages for 'usb boot'.

Page 98/516 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >

  • How to create NTFS partition in Linux to install Windows 7 from USB?

    - by Michal Stefanow
    I messed up with my computer and need help. Generally: install Windows 7 from USB. Problem: "setup was unable to create a new system partition" When first attempt to install Windows 7 failed I tried Linux live USB, installed distro to HDD, and erased all the existing partitions. Current state (fdisk -l): [writing from other computer so no copy and paste] /dev/sda1 305GB Linux /dev/sda2 7GB Extended /dev/sda5 7GB Linux Swam / Solaris To create a new, NTFS partition: fdisk /dev/sda n (for new) p (for primary) 3 (for partintion number) "No free sectors available" All the HDD was formatted couple of minutes before so there is a lot of free space but how to resize a parition? I cannot find an option for resizing in man fdisk. Some people say I should use gparted but my distro doesn't not contain this package. And my distro doesn't support wireless drivers so I have serious problems with downloading stuff. I tried also using cfdisk but any command results in: "cfdisk bad primary partition 1 partition ends in the final partial cylinder" I tried also removing partition 1 and then creating a new one (so there is no "no free sectors"). I'm receiving a warning: "Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot." After restating: "grub rescue, no known filesystem" It may indicate that some changes have been made BUT when running Windows 7 installed some another error: "Windows cannot be installed to Disk 0 Partition 1" More detailed: "Windows cannot be installed to this hard disk space. Windows must be installed to a partition formatted as NTFS." So formatting drive using Windows 7 installer BUT this time yet another error: "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information" Apparently I cannot access logs (how?) and I am back to drawing board with my live USB (this time showing partition as HPFS/NTFS). Any suggestions how to install Windows 7? Should I reinstall Linux to HDD, erase existing partitions once again, and use Parted rather than gparted (parted is included in the distro). Or maybe should I create another bootable USB such as PartedMagic to painlessly create partitions? I just want to install Windows 7 from USB, my laptop is semi-operational and I am ready to receive some help regarding fdisk and creating NTFS partitions. UPDATE: I did as suggested (removed all the partitions) and tried to install in unallocated space. Tried to create a new partition and format it. Same error: "setup was unable to create a new system partition" Came to the conclusion it may have something to do with TrueCrypt I have recently installed. Right now trying to FIX MBR (as I haven't got possibility to create rescue disc without optical drive)

    Read the article

  • Skip kernel module at boot

    - by Gris
    Hello. There is a broken kernel module, due to which I can not even load the OS, so I can not delete or fix it. Is it possible to skip this module at boot, using the kernel's parameters or something? Thanks.

    Read the article

  • Why am I unable to mount my USB drive (unknown partition table)?

    - by Pat
    I'm a real newbie to linux. Anyway the problem is that my USB doesn't get recognized anymore which is really annoying because I need information from it. I've read like a zillion threads how to manually mount it but I really can't it to work. I hope it's just some easy, stupid problem where any of you could help me out quickly.. Here is the syslog: kernel: [ 6872.420125] usb 2-2: new high-speed USB device number 11 using ehci_hcd mtp-probe: checking bus 2, device 11: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2" kernel: [ 6872.556295] scsi8 : usb-storage 2-2:1.0 mtp-probe: bus: 2, device: 11 was not an MTP device kernel: [ 6873.558081] scsi 8:0:0:0: Direct-Access SanDisk Cruzer 8.01 PQ: 0 ANSI: 0 CCS kernel: [ 6873.559964] sd 8:0:0:0: Attached scsi generic sg3 type 0 kernel: [ 6873.562833] sd 8:0:0:0: [sdc] 15682559 512-byte logical blocks: (8.02 GB/7.47 GiB) kernel: [ 6873.564867] sd 8:0:0:0: [sdc] Write Protect is off kernel: [ 6873.564878] sd 8:0:0:0: [sdc] Mode Sense: 45 00 00 08 kernel: [ 6873.565485] sd 8:0:0:0: [sdc] No Caching mode page present kernel: [ 6873.565495] sd 8:0:0:0: [sdc] Assuming drive cache: write through kernel: [ 6873.568377] sd 8:0:0:0: [sdc] No Caching mode page present kernel: [ 6873.568387] sd 8:0:0:0: [sdc] Assuming drive cache: write through kernel: [ 6873.574330] sdc: unknown partition table kernel: [ 6873.576853] sd 8:0:0:0: [sdc] No Caching mode page present kernel: [ 6873.576863] sd 8:0:0:0: [sdc] Assuming drive cache: write through kernel: [ 6873.576871] sd 8:0:0:0: [sdc] Attached SCSI removable disk Thanks in advance

    Read the article

  • shell script to start multiple Java programs from a directory at boot

    - by zcourts
    I'm not sure if this is the best approach to this, It's my first time doing all of this (including writing shell scripts). OS: Centos My problem: I want to start multiple shell scripts at boot. One of the shell scripts is to start my own services and 3 others are for third party services. The shell script to start my own services will be looking for jar files. I currently have two services (will change), written in Java. All services are named under convention prefix-service-servicename What I've done: I created the following directory structure /home/username/scripts init.sh boot/ boot/startthirdprtyservice1.sh boot/startthirdprtyservice2.sh boot/startthirdprtyservice3.sh boot/startmyservices.sh /home/username/services prefix-lib-libraryname.jar prefix-lib-libraryname.jar prefix-service-servicename.jar prefix-service-servicename.jar prefix-service-servicename.jar In init.sh I have the following: #!/bin/sh #This scripts run all executable scripts in the boot directory at boot #done by adding this script to the file /etc/rc.d/rc.local #nohup #run-parts /home/username/scripts/boot/* #for each file in the boot dir... # ignore the HUP (hangup) signal for s in ./boot/*;do if [ -x $s ]; then echo "Starting $s" nohup $s & fi done echo "Done starting bootup scripts " echo "\n" In the script boot/startmyservices.sh I have #!/bin/sh fnmatch () { case "$2" in $1) return 0 ;; esac ; return 1 ; } ##sub strin to match for SUBSTRING="prefix-service" for s in /home/username/services/*;do if [ -x $s ]; then #match service in the filename , i.e. only services are started if fnmatch "$SUBSTRING" "$s" ; then echo "Starting $s " nohup $s & fi fi done echo "Done starting Services" echo "\n" Finally: Usually you can stick a program in /etc/rc.d/rc.local for it to be run at boot but I don't think this works in this case, or rather I don't know what to put in there I've just learnt how to do this by reading up a bit so I'm not sure its particularly the best thing to do so any advice is appreciated. When I run init.sh nohup.out contains Starting the thirdparty daemon... thirdparty started... .... but nothing from myservices.sh and my Java services aren't running I'm not sure where to start debugging or what could be going wrong. Edit Found some issues and got it to work, used -x instead of -n to check if the string is none zero, needed the sub string check to also be if [[ $s = $SUBSTRING ]] ; then and this last one was just stupid, missing java -jar in front of $s Still unsure of how to get init.sh to run at boot though

    Read the article

  • Unknown file system : grub Rescue

    - by Rahul Rodrigues
    I have Lenovo Y560 Laptop on which installed Windows 7 and Ubuntu 11.10 as dual boot.Due to some reason i had to recover boot loader using bootrec.exe /fixmbr and bootrec.exe /fix boot,It created one partition of size 198MB named "tet" and my both os were working fine. Ysterday while making some changes in partition table i deleted that "tets" partition and after reboot im getting following error Error:unknow filesystem grub rescue i tried to boot from windows installer cd and but it stucks at "starting windows" so not able to run commands which i have mentioned earliar and tried to boot from Ubuntu 11.10,it stucks after showing following error memory full can't kill anymore process. Please help me out

    Read the article

  • No keyboard input until after GRUB

    - by Dave M G
    I have a computer that I dual boot between Ubuntu 11.10 and Windows 7. I installed Windows first, and Ubuntu second. When I boot, the GRUB menu comes up, showing me the option to select to boot to Ubuntu at the top of the list, and to boot to Windows at the bottom. Unfortunately, as far as I can tell, any key I press on the keyboard (connected by USB) does not get any response, so I can't actually select to boot to anything but Ubuntu (which is the default selection). Once Ubuntu loads and I am at the log in screen, then the keyboard (and mouse) work perfectly normally thereafter. Why would my keyboard not work only during GRUB? And how do I fix it?

    Read the article

  • Where did my hard drive go?

    - by Mike Carron
    I installed XBMCbuntu 11.0 to my Zotac Zbox AD03 with an OCZ Reflex 4 256gb SSK. The install worked fine and I was getting accustomed to the appearance and operation. When I attempted to boot from power-off the BIOS could no longer find the SSD. It refused to boot and when I checked in the BIOS, the SSD was missing from the boot list (it was there prior to the install). I rebooted from the install CD but when the system started it could not find the SSD. I replaced the SSD with a fresh one of the same type and reinstalled XBMCbuntu. This time I rebooted from the system several times successfully but when I shut it down and tried to cold boot, this drive was also gone. Does the installation do something strange to the boot record that could cause a BIOS to lose it? How do I fix this? mike

    Read the article

  • How to reboot into Windows from Ubuntu?

    - by andrewsomething
    I'm looking for a way to reboot into Windows from Ubuntu on a 10.10/Vista dual boot system. The specific use case is that I would like to be able to ssh into my running Ubuntu instance and issue a command that will initiate a reboot directly into Windows. I found a promising blog post, but the script that it suggests isn't working: #!/bin/bash WINDOWS_ENTRY=`grep menuentry /boot/grub/grub.cfg | grep --line-number Windows` MENU_NUMBER=$(( `echo $WINDOWS_ENTRY | sed -e "s/:.*//"` - 1 )) sudo grub-reboot $MENU_NUMBER sudo reboot man grub-reboot isn't much help, but it seems to be leading me in the right direction: set the default boot entry for GRUB, for the next boot only WINDOWS_ENTRY=`grep menuentry /boot/grub/grub.cfg | grep --line-number Windows` MENU_NUMBER=$(( `echo $WINDOWS_ENTRY | sed -e "s/:.*//"` - 1 )) echo $MENU_NUMBER This returns the expected value, but on reboot the first menu entry is still highlighted. Any ideas why this isn't working or suggestions for other solutions?

    Read the article

  • How do I modify the noacpi option?

    - by Sagar Ratnakara Nikam
    I am new to ubuntu and have stared using it since a week. I installed ubuntu server 11.10 on a VM created using VMWare player. Once installed, i tried to install ubuntu desktop using sudo apt-get install --no-install-recommends ubuntu-desktop Now I am unable to boot and i get the following error *PulseAudio configured per-user session After this, nothing happens and the ubuntu server does not boot. I read in another Q&A, the same problem and the solution. Just Installed a CLI system then ubuntu-desktop, does not boot automatically My question is how to modify noacpi option. How do i get into the boot for the ubuntu server? I have read on the net that by hitting the shift button, we can get into the boot options. I tried that, but no success, probably since i am running ubuntu on VMWare Player. Please guide me on how to solve this problem

    Read the article

  • windows system (bootloader) partition accidently deleted during multiple installs

    - by S.Y.T.
    After experimenting with multiple variations of backtrack and xbmcbuntu variations of Ubuntu with dual boot successfully, my windows partition became unrecognizable to grub. I used my windows boot CD to try to correct the problem. However, I deleted all partitions except for the NFTS one that contains my old windows install. (And, merged all other ones into that in hopes of getting back to the windows boot loader and out of grub) Now, all I get is a grub command prompt when I try and boot the system (how??? - I thought I deleted grub) And, now the windows boot disc doesn't even recognize the install. I've tried TRK to try and resolve the problem. Though I must admit ignorance in correctly using this utility. I've searched for other answers to this problem. Any help would be much appreciated. S.Y.

    Read the article

  • Cannot dual boot Ubuntu 12.10 with windows 8.

    - by Noman
    I have tried automatic partition, i Have did the partition myself but Ubuntu installs alright. But when i restart the computer it goes back to windows 8 and i Have tried easybcd boot manager but it didn't work either. I displays ubuntu on the dual boot screen but after a while the screen shutdowns and say it didn't find the boot file or the boot file was missing? Do you guys know how to solve this problem? any suggestions?

    Read the article

  • Ubuntu 14.04 not booting before Windows 8.1

    - by user280244
    I try too boot my computer into Ubuntu, but I end up having to manually select Ubuntu from the devices menu, even though it was supposed to boot first. Instead Windows 8 boots up like Ubuntu isn't even there! And GRUB works just fine when Ubuntu is selected in the boot device menu. (How else am I on?) I tried using EasyBCD but kept getting errors from the windows boot manager. And just in case it helps, during installation of Ubuntu it didn't recognize windows 8, and I had to resize and install manually. Anything I can do? Notes: EVERYONE!!! GRUB WORKS PERFECTLY!!! IT IS AN ERROR IN THE HP BOOT MENU AS I HAVE PREVIOUSLY SAID!!! PLEASE DO NOT GIVE ME ANSWERS FOR GRUB EDITS IN THE FUTURE!!! Here are my specs: PC type: HP 2000-2d49WM Notebook PC RAM: 4GB Swap: 2GB Processor: AMD E-300 Vision 1.3 GHz x2 BIOS Edition: N\A Until further notice

    Read the article

  • USB Serial cable with CDC support

    - by Harsha
    Hi All, I bought a USB to Serial cable which claims to be CDC compliant. But the bInterfaceClass value in interface descriptor is 0xFF(which is vendor specific). I was expecting it to be 0x02 (Communications and CDC control). In the device manager, i found that the drivers being loaded are ser2pl.sys and serenum.sys. I had learnt usbser.sys is the windows CDC driver, but it was not loaded for my cable. I am pretty much new to this CDC, so i have following questions 1.Does this indicate that the cable is not CDC compliant 2.Can i make this cable CDC compliant (since CDC is a driver functionality), by loading usbser.sys. If yes how?

    Read the article

  • sql exception when transferring project from usb to c:\

    - by jello
    I'm working on a C# windows program with Visual Studio 2008. Usually, I work from school, directly on my usb drive. But when I copy the folder on my hard drive at home, an sql exception is unhandled whenever I try to write to the database. it is unhandled at the conn.Open(); line. here's the exception unhandled Database 'L:\system\project\the_project\the_project\bin\Debug\PatientMonitoringDatabase.mdf' already exists. Choose a different database name. Cannot attach the file 'C:\Documents and Settings\Administrator\My Documents\system\project\the_project\the_project\bin\Debug\PatientMonitoringDatabase.mdf' as database 'PatientMonitoringDatabase'. it's weird, because my connection string says |DataDirectory|, so it should work on any drive... here's my connection string: string connStr = "Data Source=.\\SQLEXPRESS;AttachDbFilename=|DataDirectory|\\PatientMonitoringDatabase.mdf; " + "Initial Catalog=PatientMonitoringDatabase; " + "Integrated Security=True"; what's going on here?

    Read the article

  • sql exception when transferring project from usb to c:\

    - by jello
    I'm working on a C# windows program with Visual Studio 2008. Usually, I work from school, directly on my usb drive. But when I copy the folder on my hard drive at home, an sql exception is unhandled whenever I try to write to the database. it is unhandled at the conn.Open(); line. here's the exception unhandled Database 'L:\system\project\the_project\the_project\bin\Debug\PatientMonitoringDatabase.mdf' already exists. Choose a different database name. Cannot attach the file 'C:\Documents and Settings\Administrator\My Documents\system\project\the_project\the_project\bin\Debug\PatientMonitoringDatabase.mdf' as database 'PatientMonitoringDatabase'. it's weird, because my connection string says |DataDirectory|, so it should work on any drive... here's my connection string: string connStr = "Data Source=.\\SQLEXPRESS;AttachDbFilename=|DataDirectory|\\PatientMonitoringDatabase.mdf; " + "Initial Catalog=PatientMonitoringDatabase; " + "Integrated Security=True";

    Read the article

  • Capturing USB Plug/Unplug events in Firemonkey

    - by radsdau
    [RAD Studio XE3 / C++] I have a FMX project running in Windows only at this stage, but I need to detect events when USB devices are connected and disconnected. I have a similar VCL app that can do this fine, but the Application-HookMainWindow is not exposed in FMX (only VCL). Is there an elegant way to handle this? Or do I have to hack some VCL stuff into my FMX app to make that work? I'd imagine I have to abstract it so I can support other platforms down the track. For the meantime though I need to get the Windows solution working. If the 'VCL hack' thing is required, how would I reference the vcl::Forms::Application from within my Fmx app? Cheers.

    Read the article

  • USB flash drive serial number specification

    - by clyfe
    I retrieve a USB flash drive serial number by means of ioctl HDIO_GET_IDENTITY as described here. Yet, for some flash drives there is no serial (for example my SanDisk Cruzer). Why some drives don not return a serial number? a) HDIO_GET_IDENTITY not implemented in driver ? b) They just don't have one ? c) Other ? (what?) Is there a specification (like IEEE) that describes where and how the serial number is stored inside the flash drive?

    Read the article

  • Why do I get Detached Entity exception when upgrading Spring Boot 1.1.4 to 1.1.5

    - by mmeany
    On updating Spring Boot from 1.1.4 to 1.1.5 a simple web application started generating detached entity exceptions. Specifically, a post authentication inteceptor that bumped number of visits was causing the problem. A quick check of loaded dependencies showed that Spring Data has been updated from 1.6.1 to 1.6.2 and a further check of the change log shows a couple of issues relating to optimistic locking, version fields and JPA issues that have been fixed. Well I am using a version field and it starts out as Null following recommendation to not set in the specification. I have produced a very simple test scenario where I get detached entity exceptions if the version field starts as null or zero. If I create an entity with version 1 however then I do not get these exceptions. Is this expected behaviour or is there still something amiss? Below is the test scenario I have for this condition. In the scenario the service layer that has been annotated @Transactional. Each test case makes multiple calls to the service layer - the tests are working with detached entities as this is the scenario I am working with in the full blown application. The test case comprises four tests: Test 1 - versionNullCausesAnExceptionOnUpdate() In this test the version field in the detached object is Null. This is how I would usually create the object prior to passing to the service. This test fails with a Detached Entity exception. I would have expected this test to pass. If there is a flaw in the test then the rest of the scenario is probably moot. Test 2 - versionZeroCausesExceptionOnUpdate() In this test I have set the version to value Long(0L). This is an edge case test and included because I found reference to Zero values being used for version field in the Spring Data change log. This test fails with a Detached Entity exception. Of interest simply because the following two tests pass leaving this as an anomaly. Test 3 - versionOneDoesNotCausesExceptionOnUpdate() In this test the version field is set to value Long(1L). Not something I would usually do, but considering the notes in the Spring Data change log I decided to give it a go. This test passes. Would not usually set the version field, but this looks like a work-around until I figure out why the first test is failing. Test 4 - versionOneDoesNotCausesExceptionWithMultipleUpdates() Encouraged by the result of test 3 I pushed the scenario a step further and perform multiple updates on the entity that started life with a version of Long(1L). This test passes. Reinforcement that this may be a useable work-around. The entity: package com.mvmlabs.domain; import javax.persistence.Column; import javax.persistence.Entity; import javax.persistence.GeneratedValue; import javax.persistence.GenerationType; import javax.persistence.Id; import javax.persistence.Table; import javax.persistence.Version; @Entity @Table(name="user_details") public class User { @Id @GeneratedValue(strategy=GenerationType.AUTO) private Long id; @Version private Long version; @Column(nullable = false, unique = true) private String username; @Column(nullable = false) private Integer numberOfVisits; public Long getId() { return id; } public void setId(Long id) { this.id = id; } public Long getVersion() { return version; } public void setVersion(Long version) { this.version = version; } public Integer getNumberOfVisits() { return numberOfVisits == null ? 0 : numberOfVisits; } public void setNumberOfVisits(Integer numberOfVisits) { this.numberOfVisits = numberOfVisits; } public String getUsername() { return username; } public void setUsername(String username) { this.username = username; } } The repository: package com.mvmlabs.dao; import org.springframework.data.repository.CrudRepository; import com.mvmlabs.domain.User; public interface UserDao extends CrudRepository<User, Long>{ } The service interface: package com.mvmlabs.service; import com.mvmlabs.domain.User; public interface UserService { User save(User user); User loadUser(Long id); User registerVisit(User user); } The service implementation: package com.mvmlabs.service; import org.springframework.beans.factory.annotation.Autowired; import org.springframework.stereotype.Service; import org.springframework.transaction.annotation.Propagation; import org.springframework.transaction.annotation.Transactional; import org.springframework.transaction.support.TransactionSynchronizationManager; import com.mvmlabs.dao.UserDao; import com.mvmlabs.domain.User; @Service @Transactional(propagation=Propagation.REQUIRED, readOnly=false) public class UserServiceJpaImpl implements UserService { @Autowired private UserDao userDao; @Transactional(readOnly=true) @Override public User loadUser(Long id) { return userDao.findOne(id); } @Override public User registerVisit(User user) { user.setNumberOfVisits(user.getNumberOfVisits() + 1); return userDao.save(user); } @Override public User save(User user) { return userDao.save(user); } } The application class: package com.mvmlabs; import org.springframework.boot.SpringApplication; import org.springframework.boot.autoconfigure.EnableAutoConfiguration; import org.springframework.context.annotation.ComponentScan; import org.springframework.context.annotation.Configuration; @Configuration @ComponentScan @EnableAutoConfiguration public class Application { public static void main(String[] args) { SpringApplication.run(Application.class, args); } } The POM: <?xml version="1.0" encoding="UTF-8"?> <project xmlns="http://maven.apache.org/POM/4.0.0" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://maven.apache.org/POM/4.0.0 http://maven.apache.org/xsd/maven-4.0.0.xsd"> <modelVersion>4.0.0</modelVersion> <groupId>com.mvmlabs</groupId> <artifactId>jpa-issue</artifactId> <version>0.0.1-SNAPSHOT</version> <packaging>jar</packaging> <name>spring-boot-jpa-issue</name> <description>JPA Issue between spring boot 1.1.4 and 1.1.5</description> <parent> <groupId>org.springframework.boot</groupId> <artifactId>spring-boot-starter-parent</artifactId> <version>1.1.5.RELEASE</version> <relativePath /> <!-- lookup parent from repository --> </parent> <dependencies> <dependency> <groupId>org.springframework.boot</groupId> <artifactId>spring-boot-starter-data-jpa</artifactId> </dependency> <dependency> <groupId>org.hsqldb</groupId> <artifactId>hsqldb</artifactId> <scope>runtime</scope> </dependency> <dependency> <groupId>org.springframework.boot</groupId> <artifactId>spring-boot-starter-test</artifactId> <scope>test</scope> </dependency> </dependencies> <properties> <project.build.sourceEncoding>UTF-8</project.build.sourceEncoding> <start-class>com.mvmlabs.Application</start-class> <java.version>1.7</java.version> </properties> <build> <plugins> <plugin> <groupId>org.springframework.boot</groupId> <artifactId>spring-boot-maven-plugin</artifactId> </plugin> </plugins> </build> </project> The application properties: spring.jpa.hibernate.ddl-auto: create spring.jpa.hibernate.naming_strategy: org.hibernate.cfg.ImprovedNamingStrategy spring.jpa.database: HSQL spring.jpa.show-sql: true spring.datasource.url=jdbc:hsqldb:file:./target/testdb spring.datasource.username=sa spring.datasource.password= spring.datasource.driverClassName=org.hsqldb.jdbcDriver The test case: package com.mvmlabs; import org.junit.Assert; import org.junit.Test; import org.junit.runner.RunWith; import org.springframework.beans.factory.annotation.Autowired; import org.springframework.boot.test.SpringApplicationConfiguration; import org.springframework.test.context.junit4.SpringJUnit4ClassRunner; import com.mvmlabs.domain.User; import com.mvmlabs.service.UserService; @RunWith(SpringJUnit4ClassRunner.class) @SpringApplicationConfiguration(classes = Application.class) public class ApplicationTests { @Autowired UserService userService; @Test public void versionNullCausesAnExceptionOnUpdate() throws Exception { User user = new User(); user.setUsername("Version Null"); user.setNumberOfVisits(0); user.setVersion(null); user = userService.save(user); user = userService.registerVisit(user); Assert.assertEquals(new Integer(1), user.getNumberOfVisits()); Assert.assertEquals(new Long(1L), user.getVersion()); } @Test public void versionZeroCausesExceptionOnUpdate() throws Exception { User user = new User(); user.setUsername("Version Zero"); user.setNumberOfVisits(0); user.setVersion(0L); user = userService.save(user); user = userService.registerVisit(user); Assert.assertEquals(new Integer(1), user.getNumberOfVisits()); Assert.assertEquals(new Long(1L), user.getVersion()); } @Test public void versionOneDoesNotCausesExceptionOnUpdate() throws Exception { User user = new User(); user.setUsername("Version One"); user.setNumberOfVisits(0); user.setVersion(1L); user = userService.save(user); user = userService.registerVisit(user); Assert.assertEquals(new Integer(1), user.getNumberOfVisits()); Assert.assertEquals(new Long(2L), user.getVersion()); } @Test public void versionOneDoesNotCausesExceptionWithMultipleUpdates() throws Exception { User user = new User(); user.setUsername("Version One Multiple"); user.setNumberOfVisits(0); user.setVersion(1L); user = userService.save(user); user = userService.registerVisit(user); user = userService.registerVisit(user); user = userService.registerVisit(user); Assert.assertEquals(new Integer(3), user.getNumberOfVisits()); Assert.assertEquals(new Long(4L), user.getVersion()); } } The first two tests fail with detached entity exception. The last two tests pass as expected. Now change Spring Boot version to 1.1.4 and rerun, all tests pass. Are my expectations wrong? Edit: This code saved to GitHub at https://github.com/mmeany/spring-boot-detached-entity-issue

    Read the article

  • How to use BCDEdit to dual boot Windows installations?

    - by Ian Boyd
    What are the bcdedit commands necessary to setup dual boot between different installations of Windows?5 Background i recently installed Windows 8 onto a separate hard drive1. Now that Windows 8 in installed i want to dual-boot back to Windows 7. i have my two2 hard drives: So you can see that i have my two disks, with the partitions containing Windows: Windows 7: \\PhysicalDisk0 (partition 03) Windows 8: \\PhysicalDisk2 (partition 1) What i'm trying to figure out how is how to use bcdedit to instruct the thing that boots Windows that there is another Windows installation out there. Running bcdedit now, it shows current configuration: C:\WINDOWS\system32>bcdedit Windows Boot Manager -------------------- identifier {bootmgr} device partition=\Device\HarddiskVolume2 description Windows Boot Manager locale en-US inherit {globalsettings} integrityservices Enable default {current} resumeobject {ce153eb7-3786-11e2-87c0-e740e123299f} displayorder {current} toolsdisplayorder {memdiag} timeout 30 Windows Boot Loader ------------------- identifier {current} device partition=C: path \WINDOWS\system32\winload.exe description Windows 8 locale en-US inherit {bootloadersettings} recoverysequence {ce153eb9-3786-11e2-87c0-e740e123299f} integrityservices Enable recoveryenabled Yes allowedinmemorysettings 0x15000075 osdevice partition=C: systemroot \WINDOWS resumeobject {ce153eb7-3786-11e2-87c0-e740e123299f} nx OptIn bootmenupolicy Standard hypervisorlaunchtype Auto i cannot find any documentation on the difference between Windows Boot Manager and Windows Boot Loader. Documentation There is some documentation on Bcdedit: Technet: Command Line Reference - Bcdedit Technet: Windows Automated Installation Kit - BCDEdit Command Line Options Whitepaper - BCDEdit Commands for Boot Environment (Word Document) But they don't explain how edit the binary boot configuration data If i had to guess, i would think that a Windows Boot Manager instructs the BIOS what program it should run. That program would give the user a set of boot choices. That leaves Windows Boot Loader do be a particular boot choice, that represents a particular installation of Windows. If that is the case i would need to create a new Windows Boot Loader entry. This means i might want to use the /create parameter: /create Creates a new boot entry: bcdedit [/store filename] /create [id] /d description [/application apptype | /inherit [apptype] | /inherit DEVICE | /device] So i assume a syntax of: >bcdedit /create /d "The old Windows 7" /application osloader Where application can be one of the following types: Apptype Description BOOTSECTOR The boot sector application OSLOADER The Windows boot loader RESUME A resume application Unfortunately, the only documentation about osloader is "The Windows boot loader". i don't see how that can differentiate between Windows 8 on one hard drive, and Windows 7 on another. The other possible parameter when /create a boot loader is >bcdedit /create /D "Windows Vista" /device "The Quick Brown Fox" Unfortunately the documentation is missing for /device: /device Optional. If id is not set to a well-known identifier, the option that is used to specify the new boot entry as an additional device options entry. Since i did not set id to a well-known identifier, i must set /device to "the option that is used to specify the new boot entry as an additional device options entry". i know all those words; they're all English. But i have on idea what it is saying; those words in that order seem nonsensical. So i'm somewhat stymied. i don't want to be like Dan Stolts from Microsoft: I found no content that was particularly helpful when I hosed my machine by playing with BCDEdit. This post would have been ok if there was much more detail especially on the /set command OSDevice, etc. So once I got my machine fixed, I documented the solution and the information is here.... i mean, if a Microsoft guy can't even figure out how to use BCDEdit to edit his BCD, then what chance to i have? Bonus Reading BCDEdit Command-Line Options Bcdedit Server 2008 R2 or Windows 7 System Will NOT Boot After Making Changes To Boot Manager Using BCDEdit Visual BCD Editor4 Windows 7 and Windows 8 RTM Dual Boot Setup Footnotes 1 Since the Windows 8 installer would have damaged my Windows 7 install, i decided to unplug my "main" hard drive during the install. Which is a long-winded explanation of why the Windows 8 installer didn't detect the existing Windows 7 install. Normally the installer would have automatically created the required entries for dual-boot. Not that the reason i'm asking the question is important. 2 Really there's three drives, but the third is just bulk storage. The existence of a 3rd hard drive is irrelevant to the question. i only mention it in case someone wants to know why the screenshot has 3 hard drives when i only mention two. 3 i arbitrarily started numbering partitions at "zero"; not to imply that partitions are numbered starting at zero. i only mention partitions because i don't see how any boot-loader could do its job without knowing which partition, and which folder, an installation of Windows is located in. 4 i'm asking about BCDEdit. i tried Visual BCD Editor. It seems to be a visual BCD editor. That is to say that it's a GUI, but still uses the same terminology as BCDEdit, and requires the same knowledge that BCD doesn't document. 5 For simplicity sake we'll assume that all installation of Windows i want to dual-boot between are Windows Vista or later, making them all compatible with the BCDEdit and the binary boot loader. The alternative would require delving into the intricacies of the old ntloader. Nor am i asking about dual booting to Linux; or how to boot to a Virtual Hard Drive (vhd) image. Just modern versions of Windows on existing hard drives in the same machine. Note: You can ignore everything after the word Background. It's all pointless exposition to satisfy some people's need for "research effort" before they'll consider being helpful. Some people have even been known to summarily close questions unless there is research effort. Some people have been know to close questions if there is too much research effort. Some people close questions when i put the note saying that they can ignore everything after the Background out of spite. Some people are just grumpy.

    Read the article

  • How do I usb tether my Cyanogen modded G1's internet connection to my Toshiba Tecra 8000 running Xub

    - by atticus
    I have usb-tethering enabled in my phone. It works fine with Vista. When I plug my phone into my Tecra 8000 laptop running Xubuntu, dmesg shows: "usb 1-1: new full speed USB device using uhci_hcd and address 8". I see that the OS has detected it as a storage device, but I can't get it to function correctly as a network device. /dev/us* shows no usb0, but it does show /dev/usbdev1.1_ep00 /dev/usbdev1.1_ep81 /dev/usbdev1.8_ep00 ... usbdev1.8_ep83. I could just use the wireless tether app for android, but I can't get my Netgear wg511 v2 (made in China) wireless card to work in this laptop either. But that's another post for later.

    Read the article

  • Install Windows 7 x64 from a separate partition on same hard drive (no DVD/USB)?

    - by Fraser
    I'm currently running Windows XP 32-bit, and want to install Windows 7 64-bit. However, my DVD drive is broken, and the only USB sticks I have lying around are USB 1.1 only (SLOW!). So I tried (as suggested would work for a USB stick by several online guides): Created new primary partition (formatted NTFS) Set that partition as active Copied contents of Win7 x64 ISO Downloaded the 32-bit bootsect.exe Ran bootsect /nt60 F: However, when I boot into the new partition, I only see a blinking cursor on a blank screen; nothing happens. Any ideas?

    Read the article

  • Can you use a USB dongle inside a VMWare ESX Virual Machine?

    - by Keith Sirmons
    Howdy, I need to know if a USB dongle that is required as a license key for a piece of software will accessible from the physical host machine. This will be a small vSphere 4 installation targeting the quick backup and system restore capabilities of VMWare, not specifically HA, so I am not to worried about the virtual machine automatically failing over to another physical machine and the dongle not being accessible. Does ESX have the capability to map a physical USB port or device to a specific Virtual Machine? I believe this is the dongle: Sentinal Superpro USB Dongle by Rainbow Technologies Thank you, Keith

    Read the article

  • How can I chainload a USB drive from GRUB2?

    - by magic.plane
    I'm using GNU GRUB version 1.99-12ubuntu5, booted over the network using PXE. I used grub-mknetdir to generate the GRUB image and directory tree, which I'm serving on a TFTP server using Tftpd32 in Windows. I've put the latest version of Clonezilla on my USB drive using Tuxboot. Right now, in GRUB's CLI, using ls lists only the (pxe) device, even if the USB drive is plugged in before the computer is on. Is there any way I can chainload Clonezilla on my USB from GRUB, which is booted over the network?

    Read the article

  • How do I recover missing partition. Windows 8 with recovery USB?

    - by Akbar Ali
    i bought a Samsung laptop with Windows 8 preinstalled. After a year I removed Windows 8 and installed Windows 7. Before removing Windows 8, I made a Windows 8 recovery USB. Now I want to get back my original Windows 8. When I used the USB, it said missing recovery partition or partition has been deleted. Can I install Windows 8 from the internet, and if I use my recovery USB will it activate Windows or not? Or is there any other way to do this task?

    Read the article

  • How can I login to Ubuntu using a USB serial port?

    - by marc
    How can enable remote terminal login into Ubuntu 9.10 using a USB serial port? I created device /dev/ttyUSB0 and i want to allow logins using Hyper-Terminal. I found some resources but they are related to real hardware rs232 ports. I can't find any information about USB converter. So far I have established connection between that USB-serial port and my laptop. I can send text to the port (cp sometext.txt /dev/ttyUSB0) and read it using hyperterminal. What do I need to do to enable logins on this port?

    Read the article

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >