Search Results

Search found 33971 results on 1359 pages for 'ask and learn'.

Page 99/1359 | < Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >

• Intermittent wired network issues in 14.04

  - by Tommy Brunn

  Since yesterday, my wired network connection has been dropping for a couple of seconds every 30 seconds or so. To my knowledge, I had not made any changes to my network. Output of ifconfig -a: ? ~ ifconfig -a eth0 Link encap:Ethernet HWaddr 6c:f0:49:b9:b1:7f inet addr:192.168.0.16 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::6ef0:49ff:feb9:b17f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11597 errors:0 dropped:0 overruns:0 frame:0 TX packets:9783 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10101682 (10.1 MB) TX bytes:1215142 (1.2 MB) Interrupt:48 Base address:0x8000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:96691 errors:0 dropped:0 overruns:0 frame:0 TX packets:96691 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:13594355 (13.5 MB) TX bytes:13594355 (13.5 MB) lspci |grep Ethernet: 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 03) Pinging my router: ? ~ ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq=1 ttl=64 time=0.435 ms 64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=0.571 ms ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable ping: sendmsg: Network is unreachable 64 bytes from 192.168.0.1: icmp_seq=8 ttl=64 time=1.03 ms And the output of route: ? ~ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 1 0 0 eth0 Some messages from /var/logs/syslog: ? ~ tail -f /var/log/syslog Jun 6 10:37:34 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:34 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:37 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:37 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:37:39 lolbox dhclient: XMT: Solicit on eth0, interval 8660ms. Jun 6 10:37:39 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:39 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:37:47 lolbox dhclient: XMT: Solicit on eth0, interval 16820ms. Jun 6 10:37:47 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:37:47 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:04 lolbox dhclient: XMT: Solicit on eth0, interval 34410ms. Jun 6 10:38:04 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:04 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13045 Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:37:34 lolbox whoopsie[1133]: online Jun 6 10:38:16 lolbox whoopsie[1133]: offline Jun 6 10:38:16 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:38:16 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:38:16 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13044 Jun 6 10:38:16 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:38:16 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:16 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:38:16 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:16 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:38:16 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:17 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:17 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:17 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:18 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:38:18 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13160 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:38:18 lolbox NetworkManager[862]: <info> dhclient started with pid 13161 Jun 6 10:38:18 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:38:18 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:38:18 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:18 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:38:18 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:18 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:18 lolbox dhclient: All rights reserved. Jun 6 10:38:18 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:18 lolbox dhclient: Jun 6 10:38:19 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:38:19 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:38:19 lolbox dhclient: All rights reserved. Jun 6 10:38:19 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:38:19 lolbox dhclient: Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:38:19 lolbox dhclient: Bound to *:546 Jun 6 10:38:19 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:38:19 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:38:19 lolbox NetworkManager[862]: <info> (eth0): DHCPv6 state changed nbi -> preinit6 Jun 6 10:38:19 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:38:19 lolbox dhclient: Sending on Socket/fallback Jun 6 10:38:19 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3fc9376d) Jun 6 10:38:19 lolbox dhclient: XMT: Solicit on eth0, interval 1020ms. Jun 6 10:38:19 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:19 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:38:20 lolbox dhclient: bound to 192.168.0.16 -- renewal in 41481 seconds. Jun 6 10:38:20 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:38:20 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:38:20 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:38:20 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:38:20 lolbox dhclient: XMT: Solicit on eth0, interval 2110ms. Jun 6 10:38:20 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:38:20 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:38:20 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:38:20 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:38:20 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:38:21 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:38:21 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:38:21 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:38:21 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:38:21 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:38:21 lolbox whoopsie[1133]: online Jun 6 10:38:21 lolbox ntpdate[13217]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:38:21 lolbox ntpdate[13217]: no servers can be used, exiting Jun 6 10:38:22 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:38:22 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:38:22 lolbox dhclient: XMT: Solicit on eth0, interval 4080ms. Jun 6 10:38:22 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:22 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:26 lolbox dhclient: XMT: Solicit on eth0, interval 8450ms. Jun 6 10:38:26 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:26 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:35 lolbox dhclient: XMT: Solicit on eth0, interval 16630ms. Jun 6 10:38:35 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:35 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:51 lolbox dhclient: XMT: Solicit on eth0, interval 34860ms. Jun 6 10:38:51 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:38:51 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:38:58 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:38:58 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> (eth0): DHCPv6 request timed out. Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13161 Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) scheduled... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) started... Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: activated -> failed (reason 'ip-config-unavailable') [100 120 5] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> NetworkManager state is now DISCONNECTED Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> Activation (eth0) failed for connection 'Wired connection 1' Jun 6 10:38:22 lolbox whoopsie[1133]: online Jun 6 10:39:04 lolbox whoopsie[1133]: offline Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 4 of 5 (IPv6 Configure Timeout) complete. Jun 6 10:39:04 lolbox dbus[485]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): device state change: failed -> disconnected (reason 'none') [120 30 0] Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): deactivating device (reason 'none') [0] Jun 6 10:39:04 lolbox dbus[485]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Jun 6 10:39:04 lolbox NetworkManager[862]: <info> (eth0): canceled DHCP transaction, DHCP client pid 13160 Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:04 lolbox avahi-daemon[619]: Withdrawing address record for 192.168.0.16 on eth0. Jun 6 10:39:04 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:04 lolbox avahi-daemon[619]: Interface eth0.IPv4 no longer relevant for mDNS. Jun 6 10:39:04 lolbox NetworkManager[862]: <warn> DNS: plugin dnsmasq update failed Jun 6 10:39:04 lolbox NetworkManager[862]: <info> Removing DNS information from /sbin/resolvconf Jun 6 10:39:04 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:05 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:05 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:05 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:06 lolbox dnsmasq[1138]: no servers found in /var/run/dnsmasq/resolv.conf, will retry Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Auto-activating connection 'Wired connection 1'. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) starting connection 'Wired connection 1' Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: disconnected -> prepare (reason 'none') [30 40 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTING Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: prepare -> config (reason 'none') [40 50 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... Jun 6 10:39:07 lolbox NetworkManager[862]: <info> (eth0): device state change: config -> ip-config (reason 'none') [50 70 0] Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv4 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13270 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Beginning DHCPv6 transaction (timeout in 45 seconds) Jun 6 10:39:07 lolbox NetworkManager[862]: <info> dhclient started with pid 13271 Jun 6 10:39:07 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Jun 6 10:39:07 lolbox avahi-daemon[619]: Withdrawing address record for fe80::6ef0:49ff:feb9:b17f on eth0. Jun 6 10:39:07 lolbox avahi-daemon[619]: Leaving mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:07 lolbox avahi-daemon[619]: Interface eth0.IPv6 no longer relevant for mDNS. Jun 6 10:39:07 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:07 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:07 lolbox dhclient: All rights reserved. Jun 6 10:39:07 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:07 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Internet Systems Consortium DHCP Client 4.2.4 Jun 6 10:39:08 lolbox dhclient: Copyright 2004-2012 Internet Systems Consortium. Jun 6 10:39:08 lolbox dhclient: All rights reserved. Jun 6 10:39:08 lolbox dhclient: For info, please visit https://www.isc.org/software/dhcp/ Jun 6 10:39:08 lolbox dhclient: Jun 6 10:39:08 lolbox dhclient: Bound to *:546 Jun 6 10:39:08 lolbox dhclient: Listening on Socket/eth0 Jun 6 10:39:08 lolbox dhclient: Sending on Socket/eth0 Jun 6 10:39:08 lolbox kernel: [ 1446.098590] type=1400 audit(1402043948.002:75): apparmor="DENIED" operation="signal" profile="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=13273 comm="nm-dhcp-client." requested_mask="send" denied_mask="send" signal=term peer="/sbin/dhclient" Jun 6 10:39:08 lolbox kernel: [ 1446.098599] type=1400 audit(1402043948.002:76): apparmor="DENIED" operation="signal" profile="/sbin/dhclient" pid=13273 comm="nm-dhcp-client." requested_mask="receive" denied_mask="receive" signal=term peer="/usr/lib/NetworkManager/nm-dhcp-client.action" Jun 6 10:39:08 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed nbi -> preinit Jun 6 10:39:08 lolbox dhclient: Listening on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on LPF/eth0/6c:f0:49:b9:b1:7f Jun 6 10:39:08 lolbox dhclient: Sending on Socket/fallback Jun 6 10:39:08 lolbox dhclient: DHCPREQUEST of 192.168.0.16 on eth0 to 255.255.255.255 port 67 (xid=0x3e0183b9) Jun 6 10:39:08 lolbox dhclient: XMT: Solicit on eth0, interval 1050ms. Jun 6 10:39:08 lolbox dhclient: send_packet6: Cannot assign requested address Jun 6 10:39:08 lolbox dhclient: dhc6: send_packet6() sent -1 of 77 bytes Jun 6 10:39:09 lolbox dhclient: DHCPACK of 192.168.0.16 from 192.168.0.1 Jun 6 10:39:09 lolbox dhclient: bound to 192.168.0.16 -- renewal in 35498 seconds. Jun 6 10:39:09 lolbox NetworkManager[862]: <info> (eth0): DHCPv4 state changed preinit -> reboot Jun 6 10:39:09 lolbox NetworkManager[862]: <info> address 192.168.0.16 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> prefix 24 (255.255.255.0) Jun 6 10:39:09 lolbox NetworkManager[862]: <info> gateway 192.168.0.1 Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '83.255.245.11' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> nameserver '193.150.193.150' Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Configure Commit) scheduled... Jun 6 10:39:09 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) started... Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv4 with address 192.168.0.16. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv4 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for 192.168.0.16 on eth0.IPv4. Jun 6 10:39:09 lolbox avahi-daemon[619]: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::6ef0:49ff:feb9:b17f. Jun 6 10:39:09 lolbox avahi-daemon[619]: New relevant interface eth0.IPv6 for mDNS. Jun 6 10:39:09 lolbox avahi-daemon[619]: Registering new address record for fe80::6ef0:49ff:feb9:b17f on eth0.*. Jun 6 10:39:10 lolbox dhclient: XMT: Solicit on eth0, interval 2180ms. Jun 6 10:39:10 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:10 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: ip-config -> secondaries (reason 'none') [70 90 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) Stage 5 of 5 (IPv4 Commit) complete. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> (eth0): device state change: secondaries -> activated (reason 'none') [90 100 0] Jun 6 10:39:10 lolbox NetworkManager[862]: <info> NetworkManager state is now CONNECTED_GLOBAL Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Policy set 'Wired connection 1' (eth0) as default for IPv4 routing and DNS. Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Writing DNS information to /sbin/resolvconf Jun 6 10:39:10 lolbox dnsmasq[1362]: setting upstream servers from DBus Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 127.0.0.1#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 193.150.193.150#53 Jun 6 10:39:10 lolbox dnsmasq[1362]: using nameserver 83.255.245.11#53 Jun 6 10:39:10 lolbox NetworkManager[862]: <info> Activation (eth0) successful, device activated. Jun 6 10:39:10 lolbox whoopsie[1133]: message repeated 2 times: [ offline] Jun 6 10:39:10 lolbox whoopsie[1133]: online Jun 6 10:39:10 lolbox ntpdate[13339]: Can't find host ntp.ubuntu.com: Name or service not known (-2) Jun 6 10:39:10 lolbox ntpdate[13339]: no servers can be used, exiting Jun 6 10:39:11 lolbox dnsmasq[1138]: reading /var/run/dnsmasq/resolv.conf Jun 6 10:39:11 lolbox dnsmasq[1138]: using nameserver 127.0.1.1#53 Jun 6 10:39:12 lolbox dhclient: XMT: Solicit on eth0, interval 4350ms. Jun 6 10:39:12 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:12 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:16 lolbox dhclient: XMT: Solicit on eth0, interval 8740ms. Jun 6 10:39:16 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:16 lolbox dhclient: IA_NA status code NoAddrsAvail. Jun 6 10:39:17 lolbox dnsmasq[1138]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:17 lolbox dnsmasq[1362]: Maximum number of concurrent DNS queries reached (max: 150) Jun 6 10:39:25 lolbox dhclient: XMT: Solicit on eth0, interval 17610ms. Jun 6 10:39:25 lolbox dhclient: RCV: Advertise message on eth0 from fe80::120d:7fff:fe97:9d54. Jun 6 10:39:25 lolbox dhclient: IA_NA status code NoAddrsAvail.

  Read the article

• Google chrome cannot be installed

  - by Zxy

  I downloaded latest version of google chrome and then tried to install it. However it gave me errors. I searched through the net and noticed that most of the people's problem solved when they installed missing dependecies. Therefore I tried to install them too but seems like it does not work. zero@ubuntu:~/Downloads$ sudo apt-get install -f Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages will be REMOVED: google-chrome-stable:i386 0 upgraded, 0 newly installed, 1 to remove and 23 not upgraded. 1 not fully installed or removed. After this operation, 116 MB disk space will be freed. Do you want to continue [Y/n]? Y (Reading database ... 169296 files and directories currently installed.) Removing google-chrome-stable:i386 ... Processing triggers for man-db ... Processing triggers for desktop-file-utils ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for gnome-menus ... zero@ubuntu:~/Downloads$ sudo dpkg -i google-chrome-stable_current_i386.deb Selecting previously unselected package google-chrome-stable:i386. (Reading database ... 169201 files and directories currently installed.) Unpacking google-chrome-stable:i386 (from google-chrome-stable_current_i386.deb) ... dpkg: dependency problems prevent configuration of google-chrome-stable:i386: google-chrome-stable:i386 depends on xdg-utils (>= 1.0.2). dpkg: error processing google-chrome-stable:i386 (--install): dependency problems - leaving unconfigured Processing triggers for desktop-file-utils ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for gnome-menus ... Processing triggers for man-db ... Errors were encountered while processing: google-chrome-stable:i386 Could you please help me? Thanks.

  Read the article

• No satellite image in world wind

  - by julien

  I am trying to use world wind but instead of a nice globe, I have that: As you can see, the earth is transparent. Only stars, the atmosphere and some names are displayed. The satellite image and the terrain are absent. If you do not know this application, you can test it with java web start from there. Do you know how to solve this problem? Maybe there is something wrong with my 3D card (FYI, google earth works perfectly). I am on ubuntu 12.04, with openJDK6 and icedtea web start.

  Read the article

• Fan running continously on HP Pavillion G6 notebook with 12.04.1 LTS, help please?

  - by Ankit

  Fan is running continously on my HP Pavillion G6 notebook with 12.04.1 LTS. My system specifications are:- Ram: 6Gb Graphics Card:- 1 GB (AMD Raedon 64XX). HDD: 540 GB. Please find a list of ACPI errors logs from dmesg as follows:- buffer@ankit:~$ dmesg | grep ACPI -i [ 0.000000] BIOS-e820: 000000009cebf000 - 000000009cfbf000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000009cfbf000 - 000000009cfff000 (ACPI data) [ 0.000000] ACPI: RSDP 00000000000fe020 00024 (v02 HPQOEM) [ 0.000000] ACPI: XSDT 000000009cffe120 00084 (v01 HPQOEM SLIC-MPC 00000001 01000013) [ 0.000000] ACPI: FACP 000000009cffc000 000F4 (v04 HPQOEM SLIC-MPC 00000001 MSFT 01000013) [ 0.000000] ACPI: DSDT 000000009cfec000 0C132 (v01 HP 1670 00000000 MSFT 01000013) [ 0.000000] ACPI: FACS 000000009cf6c000 00040 [ 0.000000] ACPI: ASF! 000000009cffd000 000A5 (v32 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: HPET 000000009cffb000 00038 (v01 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: APIC 000000009cffa000 0008C (v02 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: MCFG 000000009cff9000 0003C (v01 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: SLIC 000000009cfeb000 00176 (v01 HPQOEM SLIC-MPC 00000001 MSFT 01000013) [ 0.000000] ACPI: SSDT 000000009cfea000 00D52 (v01 HP 1670 00001000 MSFT 01000013) [ 0.000000] ACPI: BOOT 000000009cfe8000 00028 (v01 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: ASPT 000000009cfe5000 00034 (v07 HP 1670 00000001 MSFT 01000013) [ 0.000000] ACPI: SSDT 000000009cfe4000 00780 (v01 HP 1670 00003000 INTL 20100121) [ 0.000000] ACPI: SSDT 000000009cfe3000 00996 (v01 HP 1670 00003000 INTL 20100121) [ 0.000000] ACPI: SSDT 000000009cfdd000 0219F (v01 HP 1670 00001000 INTL 20100121) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled) [ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0]) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.005902] ACPI: Core revision 20110623 [ 0.536006] PM: Registering ACPI NVS region at 9cebf000 (1048576 bytes) [ 0.538423] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it [ 0.538429] ACPI: bus type pci registered [ 0.656088] ACPI: Added _OSI(Module Device) [ 0.656094] ACPI: Added _OSI(Processor Device) [ 0.656098] ACPI: Added _OSI(3.0 _SCP Extensions) [ 0.656103] ACPI: Added _OSI(Processor Aggregator Device) [ 0.660335] ACPI: EC: Look up EC in DSDT [ 0.664416] ACPI: Executed 1 blocks of module-level executable AML code [ 0.728303] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored [ 0.729536] ACPI: SSDT 000000009ce70798 00727 (v01 PmRef Cpu0Cst 00003001 INTL 20100121) [ 0.730622] ACPI: Dynamic OEM Table Load: [ 0.730630] ACPI: SSDT (null) 00727 (v01 PmRef Cpu0Cst 00003001 INTL 20100121) [ 0.760829] ACPI: SSDT 000000009ce71a98 00303 (v01 PmRef ApIst 00003000 INTL 20100121) [ 0.761992] ACPI: Dynamic OEM Table Load: [ 0.761998] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20100121) [ 0.792451] ACPI: SSDT 000000009ce6fd98 00119 (v01 PmRef ApCst 00003000 INTL 20100121) [ 0.793521] ACPI: Dynamic OEM Table Load: [ 0.793528] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20100121) [ 0.872981] ACPI: Interpreter enabled [ 0.872992] ACPI: (supports S0 S3 S4 S5) [ 0.873064] ACPI: Using IOAPIC for interrupt routing [ 0.882723] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62 [ 0.883072] ACPI: No dock devices found. [ 0.883084] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug [ 0.883882] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-fe]) [ 0.924187] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.924509] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] [ 0.924581] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] [ 0.924659] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT] [ 0.924758] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEG0._PRT] [ 0.924973] pci0000:00: Requesting ACPI _OSC control (0x1d) [ 0.925064] pci0000:00: ACPI _OSC request failed (AE_ERROR), returned control mask: 0x1d [ 0.925069] ACPI _OSC control for PCIe not granted, disabling ASPM [ 0.930212] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930327] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930436] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930547] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 *10 11 12 14 15) [ 0.930655] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled. [ 0.930764] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled. [ 0.930873] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 10 *11 12 14 15) [ 0.930979] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 10 11 12 14 15) *0, disabled. [ 0.932142] PCI: Using ACPI for IRQ routing [ 0.967119] pnp: PnP ACPI init [ 0.967151] ACPI: bus type pnp registered [ 0.968356] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.968516] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active) [ 0.968586] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active) [ 0.968818] pnp 00:03: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.968915] pnp 00:04: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.969206] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.969293] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.969418] pnp 00:07: Plug and Play ACPI device, IDs PNP0303 (active) [ 0.969528] pnp 00:08: Plug and Play ACPI device, IDs SYN1e3f SYN1e00 SYN0002 PNP0f13 (active) [ 0.969969] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.970574] system 00:0a: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.970617] pnp: PnP ACPI: found 11 devices [ 0.970622] ACPI: ACPI bus type pnp unregistered [ 1.138064] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.138331] ACPI: AC Adapter [ACAD] (off-line) [ 1.139068] ACPI: Lid Switch [LID0] [ 1.139176] ACPI: Power Button [PWRB] [ 1.139286] ACPI: Power Button [PWRF] [ 1.144637] ACPI: Thermal Zone [TZ01] (0 C) [ 1.144677] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 1.144693] ACPI: Battery Slot [BAT0] (battery present) [ 1.206926] ACPI: Battery Slot [BAT0] (battery present) [ 13.176993] acpi device:1a: registered as cooling_device4 [ 13.179931] acpi device:1b: registered as cooling_device5 [ 13.180221] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) [ 13.219589] acpi device:20: registered as cooling_device6 [ 13.220851] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 1649.915134] i8042 aux 00:08: wake-up capability disabled by ACPI [ 1649.915147] i8042 kbd 00:07: wake-up capability enabled by ACPI [ 1650.931028] r8169 0000:03:00.0: wake-up capability enabled by ACPI [ 1650.954743] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI [ 1650.978733] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI [ 1651.010950] ACPI: Preparing to enter system sleep state S3 [ 1652.251505] ACPI: Low-level resume complete [ 1652.360953] ACPI: Waking up from system sleep state S3 [ 1652.427581] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI [ 1652.435579] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI [ 1652.437887] r8169 0000:03:00.0: wake-up capability disabled by ACPI [ 1652.506660] i8042 kbd 00:07: wake-up capability disabled by ACPI [ 1661.238234] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [ 1661.238253] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [ 1661.238268] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [ 3151.784288] i8042 aux 00:08: wake-up capability disabled by ACPI [ 3151.784301] i8042 kbd 00:07: wake-up capability enabled by ACPI [ 3152.797676] r8169 0000:03:00.0: wake-up capability enabled by ACPI [ 3152.821379] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI [ 3152.845367] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI [ 3152.877600] ACPI: Preparing to enter system sleep state S3 [ 3154.313213] ACPI: Low-level resume complete [ 3154.422297] ACPI: Waking up from system sleep state S3 [ 3154.489692] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI [ 3154.497667] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI [ 3154.505947] r8169 0000:03:00.0: wake-up capability disabled by ACPI [ 3154.568985] i8042 kbd 00:07: wake-up capability disabled by ACPI [ 3162.745149] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [ 3162.745168] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [ 3162.745183] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [ 6775.723501] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [ 6775.723519] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [ 6775.723535] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [10388.004760] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [10388.004778] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [10388.004801] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/psparse-536) [10723.591930] i8042 aux 00:08: wake-up capability disabled by ACPI [10723.591942] i8042 kbd 00:07: wake-up capability enabled by ACPI [10724.607624] r8169 0000:03:00.0: wake-up capability enabled by ACPI [10724.631349] ehci_hcd 0000:00:1d.0: wake-up capability enabled by ACPI [10724.655339] ehci_hcd 0000:00:1a.0: wake-up capability enabled by ACPI [10724.687572] ACPI: Preparing to enter system sleep state S3 [10726.123176] ACPI: Low-level resume complete [10726.232181] ACPI: Waking up from system sleep state S3 [10726.303653] ehci_hcd 0000:00:1a.0: wake-up capability disabled by ACPI [10726.311648] ehci_hcd 0000:00:1d.0: wake-up capability disabled by ACPI [10726.315734] r8169 0000:03:00.0: wake-up capability disabled by ACPI [10726.379287] i8042 kbd 00:07: wake-up capability disabled by ACPI [10734.393523] ACPI Error: No handler for Region [CMS0] (ffff8801d5035558) [SystemCMOS] (20110623/evregion-373) [10734.393542] ACPI Error: Region SystemCMOS (ID=5) has no handler (20110623/exfldio-292) [10734.393557] ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPCB.EC0_._Q33] (Node ffff8801d5054de8), AE_NOT_EXIST (20110623/ps Continuous sound from the fan is very annoying, any help would highly appreciated.

  Read the article

• Triple boot vista xp ubuntu

  - by Artyom2033

  My partition table is pretty messed up from install/uninstall os and what I want to do now is to clear that and have vista/xp/ubuntu 12.04 on the same hard drive. I have create a new partition for xp on vista, everything was fine, but when I restarted my pc, I was getting the grub restore prompt. Even when I was trying to install xp, when the 'lunch windows' came, a wild BSOD appear. So I have deleted my partition for xp using gParted include in the 12.04 live cd. This haven't resolve the problem and I am still unable to boot in vista nor ubuntu. But I realy what this triple boot for LoL purpose (since my vista installation keep giving latency spike in this game and I hope this will not be the case in a fresh xp installation (I have tested it in ubuntu, the ping was good, but the fps wasn't). So what I want to do, is to install xp on a partition, then be able to boot on any of them without a problem from a nice installation of grub or something. gParted screenshot Thanks for help. Sorry for my English.

  Read the article

• System can't sleep, can't shutdown (might be networking related)

  - by Kevin Q

  I speculate it's networking related since I could only shut down my system if I do /etc/init.d/networking stop first. If I tried to put the system to sleep, it disconnect the network then reconnect it automatically, never goes to sleep. I uninstalled the network manager, then /etc/init.d/networking stop will not help shutdown the system anymore. When I boot into the OS, there were some warning about Unknown job:S20acpid,S20network-interface, S20network-manager . I got some advices to do update-rc.d -f to remove all those script, which I am not certain if it's right thing to do. The messages are gone but the problem remains. When I tried to restart, I used to get this message It doesn't seem to be the modem manager since I later removed it. Once upon a time, the fronze shutting down/restarting can be restarted when I presses Ctrl+Alt+Delete, and it says something like networking is stopped externally. If I log in single user mode, and shutdown or reboot, it show this screen I also tried GRUB_CMDLINE_LINUX_DEFAULT = "acpi=force" This is a Ubuntu 12.04 running on Thinkpad T520, not new installation, no such problems occurred before.

  Read the article

• Java installation problem

  - by Zxy

  I cannot install java on my ubuntu 12.04: zero@ghostrider:~$ sudo apt-get purge openjdk* [sudo] password for zero: Reading package lists... Done Building dependency tree Reading state information... Done Note, selecting 'openjdk-6-demo' for regex 'openjdk*' Note, selecting 'openjdk-7-jre-headless' for regex 'openjdk*' Note, selecting 'uwsgi-plugin-jwsgi-openjdk-6' for regex 'openjdk*' Note, selecting 'openjdk-jre' for regex 'openjdk*' Note, selecting 'openjdk-7-source' for regex 'openjdk*' Note, selecting 'openjdk-6-dbg' for regex 'openjdk*' Note, selecting 'openjdk7-jdk' for regex 'openjdk*' Note, selecting 'openjdk-6-doc' for regex 'openjdk*' Note, selecting 'openjdk-7-jre-zero' for regex 'openjdk*' Note, selecting 'openjdk-7-demo' for regex 'openjdk*' Note, selecting 'openjdk-6-jre-headless' for regex 'openjdk*' Note, selecting 'openjdk-6-jdk' for regex 'openjdk*' Note, selecting 'openjdk-6-jre' for regex 'openjdk*' Note, selecting 'openjdk-6-jre-lib' for regex 'openjdk*' Note, selecting 'openjdk-6-jre-zero' for regex 'openjdk*' Note, selecting 'openjdk-7-dbg' for regex 'openjdk*' Note, selecting 'openjdk-7-doc' for regex 'openjdk*' Note, selecting 'openjdk-7-jdk' for regex 'openjdk*' Note, selecting 'openjdk-7-jre' for regex 'openjdk*' Note, selecting 'openjdk-6-source' for regex 'openjdk*' Note, selecting 'openjdk-7-jre-lib' for regex 'openjdk*' Note, selecting 'uwsgi-plugin-jvm-openjdk-6' for regex 'openjdk*' Package uwsgi-plugin-jvm-openjdk-6 is not installed, so not removed Package uwsgi-plugin-jwsgi-openjdk-6 is not installed, so not removed Package openjdk-6-dbg is not installed, so not removed Package openjdk-6-demo is not installed, so not removed Package openjdk-6-doc is not installed, so not removed Package openjdk-6-jdk is not installed, so not removed Package openjdk-6-jre is not installed, so not removed Package openjdk-6-jre-headless is not installed, so not removed Package openjdk-6-jre-lib is not installed, so not removed Package openjdk-6-source is not installed, so not removed Package openjdk-6-jre-zero is not installed, so not removed Package openjdk-7-dbg is not installed, so not removed Package openjdk-7-demo is not installed, so not removed Package openjdk-7-doc is not installed, so not removed Package openjdk-7-jdk is not installed, so not removed Package openjdk-7-jre is not installed, so not removed Package openjdk-7-jre-headless is not installed, so not removed Package openjdk-7-jre-lib is not installed, so not removed Package openjdk-7-jre-zero is not installed, so not removed Package openjdk-7-source is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Setting up oracle-java7-installer (7u3-0~eugenesan~precise4) ... Downloading... --2012-06-11 23:56:42-- http://download.oracle.com/otn-pub/java/jdk/7u3-b04/jdk- 7u3-linux-i586.tar.gz Resolving download.oracle.com (download.oracle.com)... 64.209.77.18 Connecting to download.oracle.com (download.oracle.com)|64.209.77.18|:80... connected. HTTP request sent, awaiting response... 302 Moved Temporarily Location: https://edelivery.oracle.com/otn-pub/java/jdk/7u3-b04/jdk-7u3-linux-i586.tar.gz [following] --2012-06-11 23:56:42-- https://edelivery.oracle.com/otn-pub/java/jdk/7u3-b04/jdk-7u3-linux-i586.tar.gz Resolving edelivery.oracle.com (edelivery.oracle.com)... 95.101.122.174 Connecting to edelivery.oracle.com (edelivery.oracle.com)|95.101.122.174|:443... connected. HTTP request sent, awaiting response... 302 Moved Temporarily Location: http://download.oracle.com/errors/download-fail-1505220.html [following] --2012-06-11 23:56:44-- http://download.oracle.com/errors/download-fail-1505220.html Connecting to download.oracle.com (download.oracle.com)|64.209.77.18|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 5307 (5.2K) [text/html] Saving to: `./jdk-7u3-linux-i586.tar.gz' 0K ..... 100% 1007K=0.005s 2012-06-11 23:56:44 (1007 KB/s) - `./jdk-7u3-linux-i586.tar.gz' saved [5307/5307] Download done. sha256sum mismatch jdk-7u3-linux-i586.tar.gz Oracle JDK 7 is NOT installed. dpkg: error processing oracle-java7-installer (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already Errors were encountered while processing: oracle-java7-installer E: Sub-process /usr/bin/dpkg returned an error code (1) zero@ghostrider:~$ sudo add-apt-repository ppa:eugenesan/java You are about to add the following PPA to your system: More info: https://launchpad.net/~eugenesan/+archive/java Press [ENTER] to continue or ctrl-c to cancel adding it Executing: gpg --ignore-time-conflict --no-options --no-default-keyring --secret- keyring /tmp/tmp.uGcZHfsoNF --trustdb-name /etc/apt/trustdb.gpg --keyring /etc/apt/trusted.gpg --primary-keyring /etc/apt/trusted.gpg --keyserver hkp://keyserver.ubuntu.com:80/ --recv 4346FBB158F4022C896164EEE61380B28313A596 gpg: requesting key 8313A596 from hkp server keyserver.ubuntu.com gpg: key 8313A596: "Launchpad synergy+" not changed gpg: Total number processed: 1 gpg: unchanged: 1 zero@ghostrider:~$ sudo apt-get update Ign http://tr.archive.ubuntu.com precise InRelease Ign http://tr.archive.ubuntu.com precise-updates InRelease Ign http://tr.archive.ubuntu.com precise-backports InRelease Hit http://tr.archive.ubuntu.com precise Release.gpg Hit http://tr.archive.ubuntu.com precise-updates Release.gpg Hit http://tr.archive.ubuntu.com precise-backports Release.gpg Hit http://tr.archive.ubuntu.com precise Release Ign http://extras.ubuntu.com precise InRelease Ign http://security.ubuntu.com precise-security InRelease Hit http://tr.archive.ubuntu.com precise-updates Release Ign http://ppa.launchpad.net precise InRelease Hit http://tr.archive.ubuntu.com precise-backports Release Hit http://tr.archive.ubuntu.com precise/main Sources Hit http://tr.archive.ubuntu.com precise/restricted Sources Hit http://tr.archive.ubuntu.com precise/universe Sources Hit http://tr.archive.ubuntu.com precise/multiverse Sources Hit http://tr.archive.ubuntu.com precise/main i386 Packages Hit http://tr.archive.ubuntu.com precise/restricted i386 Packages Hit http://tr.archive.ubuntu.com precise/universe i386 Packages Hit http://extras.ubuntu.com precise Release.gpg Hit http://ppa.launchpad.net precise Release.gpg Hit http://security.ubuntu.com precise-security Release.gpg Hit http://tr.archive.ubuntu.com precise/multiverse i386 Packages Hit http://tr.archive.ubuntu.com precise/main TranslationIndex Hit http://tr.archive.ubuntu.com precise/multiverse TranslationIndex Hit http://tr.archive.ubuntu.com precise/restricted TranslationIndex Hit http://tr.archive.ubuntu.com precise/universe TranslationIndex Hit http://tr.archive.ubuntu.com precise-updates/main Sources Hit http://tr.archive.ubuntu.com precise-updates/restricted Sources Hit http://tr.archive.ubuntu.com precise-updates/universe Sources Hit http://tr.archive.ubuntu.com precise-updates/multiverse Sources Hit http://tr.archive.ubuntu.com precise-updates/main i386 Packages Hit http://extras.ubuntu.com precise Release Hit http://ppa.launchpad.net precise Release Hit http://security.ubuntu.com precise-security Release Hit http://tr.archive.ubuntu.com precise-updates/restricted i386 Packages Hit http://tr.archive.ubuntu.com precise-updates/universe i386 Packages Hit http://tr.archive.ubuntu.com precise-updates/multiverse i386 Packages Hit http://tr.archive.ubuntu.com precise-updates/main TranslationIndex Hit http://tr.archive.ubuntu.com precise-updates/multiverse TranslationIndex Hit http://tr.archive.ubuntu.com precise-updates/restricted TranslationIndex Hit http://tr.archive.ubuntu.com precise-updates/universe TranslationIndex Hit http://tr.archive.ubuntu.com precise-backports/main Sources Hit http://tr.archive.ubuntu.com precise-backports/restricted Sources Hit http://tr.archive.ubuntu.com precise-backports/universe Sources Hit http://tr.archive.ubuntu.com precise-backports/multiverse Sources Hit http://tr.archive.ubuntu.com precise-backports/main i386 Packages Hit http://tr.archive.ubuntu.com precise-backports/restricted i386 Packages Hit http://tr.archive.ubuntu.com precise-backports/universe i386 Packages Hit http://tr.archive.ubuntu.com precise-backports/multiverse i386 Packages Hit http://tr.archive.ubuntu.com precise-backports/main TranslationIndex Hit http://extras.ubuntu.com precise/main Sources Hit http://ppa.launchpad.net precise/main Sources Hit http://security.ubuntu.com precise-security/main Sources Hit http://tr.archive.ubuntu.com precise-backports/multiverse TranslationIndex Hit http://tr.archive.ubuntu.com precise-backports/restricted TranslationIndex Hit http://tr.archive.ubuntu.com precise-backports/universe TranslationIndex Hit http://tr.archive.ubuntu.com precise/main Translation-en Hit http://tr.archive.ubuntu.com precise/multiverse Translation-en Hit http://extras.ubuntu.com precise/main i386 Packages Ign http://extras.ubuntu.com precise/main TranslationIndex Hit http://tr.archive.ubuntu.com precise/restricted Translation-en Hit http://tr.archive.ubuntu.com precise/universe Translation-en Hit http://tr.archive.ubuntu.com precise-updates/main Translation-en Hit http://tr.archive.ubuntu.com precise-updates/multiverse Translation-en Hit http://tr.archive.ubuntu.com precise-updates/restricted Translation-en Hit http://ppa.launchpad.net precise/main i386 Packages Ign http://ppa.launchpad.net precise/main TranslationIndex Hit http://security.ubuntu.com precise-security/restricted Sources Hit http://security.ubuntu.com precise-security/universe Sources Hit http://security.ubuntu.com precise-security/multiverse Sources Hit http://security.ubuntu.com precise-security/main i386 Packages Hit http://security.ubuntu.com precise-security/restricted i386 Packages Hit http://tr.archive.ubuntu.com precise-updates/universe Translation-en Hit http://tr.archive.ubuntu.com precise-backports/main Translation-en Hit http://tr.archive.ubuntu.com precise-backports/multiverse Translation-en Hit http://tr.archive.ubuntu.com precise-backports/restricted Translation-en Hit http://tr.archive.ubuntu.com precise-backports/universe Translation-en Hit http://security.ubuntu.com precise-security/universe i386 Packages Hit http://security.ubuntu.com precise-security/multiverse i386 Packages Hit http://security.ubuntu.com precise-security/main TranslationIndex Hit http://security.ubuntu.com precise-security/multiverse TranslationIndex Hit http://security.ubuntu.com precise-security/restricted TranslationIndex Hit http://security.ubuntu.com precise-security/universe TranslationIndex Hit http://security.ubuntu.com precise-security/main Translation-en Hit http://security.ubuntu.com precise-security/multiverse Translation-en Hit http://security.ubuntu.com precise-security/restricted Translation-en Hit http://security.ubuntu.com precise-security/universe Translation-en Ign http://ppa.launchpad.net precise/main Translation-en_US Ign http://extras.ubuntu.com precise/main Translation-en_US Ign http://ppa.launchpad.net precise/main Translation-en Ign http://extras.ubuntu.com precise/main Translation-en Reading package lists... Done zero@ghostrider:~$ sudo apt-get install oracle-java7-installer Reading package lists... Done Building dependency tree Reading state information... Done oracle-java7-installer is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? Y Setting up oracle-java7-installer (7u3-0~eugenesan~precise4) ... Downloading... --2012-06-11 23:57:11-- http://download.oracle.com/otn-pub/java/jdk/7u3-b04/jdk- 7u3-linux-i586.tar.gz Resolving download.oracle.com (download.oracle.com)... 64.209.77.18 Connecting to download.oracle.com (download.oracle.com)|64.209.77.18|:80... connected. HTTP request sent, awaiting response... 302 Moved Temporarily Location: https://edelivery.oracle.com/otn-pub/java/jdk/7u3-b04/jdk-7u3-linux-i586.tar.gz [following] --2012-06-11 23:57:11-- https://edelivery.oracle.com/otn-pub/java/jdk/7u3-b04/jdk-7u3-linux-i586.tar.gz Resolving edelivery.oracle.com (edelivery.oracle.com)... 95.101.122.174 Connecting to edelivery.oracle.com (edelivery.oracle.com)|95.101.122.174|:443... connected. HTTP request sent, awaiting response... 302 Moved Temporarily Location: http://download.oracle.com/errors/download-fail-1505220.html [following] --2012-06-11 23:57:12-- http://download.oracle.com/errors/download-fail-1505220.html Connecting to download.oracle.com (download.oracle.com)|64.209.77.18|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 5307 (5.2K) [text/html] Saving to: `./jdk-7u3-linux-i586.tar.gz' 0K ..... 100% 976K=0.005s 2012-06-11 23:57:12 (976 KB/s) - `./jdk-7u3-linux-i586.tar.gz' saved [5307/5307] Download done. sha256sum mismatch jdk-7u3-linux-i586.tar.gz Oracle JDK 7 is NOT installed. dpkg: error processing oracle-java7-installer (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already Errors were encountered while processing: oracle-java7-installer E: Sub-process /usr/bin/dpkg returned an error code (1) zero@ghostrider:~$

  Read the article

• Errors Code: /var/cache/apt/archives/linux-image-3.8.0-19-generic_3.8.0-19.30~precise1_amd64.deb

  - by user286682

  $ sudo apt-get dist-upgrade Reading package lists... Done Building dependency tree Reading state information... Done Calculating upgrade... Done The following packages will be upgraded: linux-image-3.8.0-19-generic 1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 6 not fully installed or removed. Need to get 0 B/47.8 MB of archives. After this operation, 142 MB of additional disk space will be used. Do you want to continue [Y/n]? y (Reading database ... 164064 files and directories currently installed.) Preparing to replace linux-image-3.8.0-19-generic 3.8.0-19.29 (using .../linux-image-3.8.0-19-generic_3.8.0-19.30~precise1_amd64.deb) ... Done. Unpacking replacement linux-image-3.8.0-19-generic ... dpkg: error processing /var/cache/apt/archives/linux-image-3.8.0-19-generic_3.8.0-19.30~precise1_amd64.deb (--unpack): trying to overwrite '/lib/modules/3.8.0-19-generic/kernel/arch/x86/kvm/kvm-intel.ko', which is also in package linux-image-extra-3.8.0-19-generic 3.8.0-19.29 dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Examining /etc/kernel/postrm.d . run-parts: executing /etc/kernel/postrm.d/initramfs-tools 3.8.0-19-generic /boot/vmlinuz-3.8.0-19-generic run-parts: executing /etc/kernel/postrm.d/zz-update-grub 3.8.0-19-generic /boot/vmlinuz-3.8.0-19-generic Errors were encountered while processing: /var/cache/apt/archives/linux-image-3.8.0-19-generic_3.8.0-19.30~precise1_amd64.deb E: Sub-process /usr/bin/dpkg returned an error code (1) How can I get this update to work?

  Read the article

• Ubuntu 12.04 patched b43 driver compilation error

  - by Zed

  I tried this How do I install this patched b43 driver? guide to install patched b43 driver on Ubuntu 12.04 with 3.2.0-31-generic kernel but I can't pass compilation phase.Here is what I did: wget http://www.orbit-lab.org/kernel/compat-wireless-3-stable/v3.1/compat-wireless-3.1.1-1.tar.bz2 cd compat-wireless-3.1.1-1/ scripts/driver-select b43 make make -C /lib/modules/3.2.0-31-generic/build M=/home/marco/compat-wireless-3.1.1-1 modules make[1]: Entering directory `/usr/src/linux-headers-3.2.0-31-generic' CC [M] /home/marco/compat-wireless-3.1.1-1/compat/main.o In file included from /home/marco/compat-wireless-3.1.1-1/include/linux/compat-2.6.29.h:5:0, from /home/marco/compat-wireless-3.1.1-1/include/linux/compat-2.6.h:24, from <command-line>:0: include/linux/netdevice.h:1153:5: warning: "IS_ENABLED" is not defined [-Wundef] include/linux/netdevice.h:1153:15: error: missing binary operator before token "(" include/linux/netdevice.h: In function ‘netdev_uses_dsa_tags’: include/linux/netdevice.h:1421:9: error: ‘struct net_device’ has no member named ‘dsa_ptr’ include/linux/netdevice.h:1422:31: error: ‘struct net_device’ has no member named ‘dsa_ptr’ include/linux/netdevice.h: In function ‘netdev_uses_trailer_tags’: include/linux/netdevice.h:1431:9: error: ‘struct net_device’ has no member named ‘dsa_ptr’ include/linux/netdevice.h:1432:35: error: ‘struct net_device’ has no member named ‘dsa_ptr’ make[3]: *** [/home/marco/compat-wireless-3.1.1-1/compat/main.o] Error 1 make[2]: *** [/home/marco/compat-wireless-3.1.1-1/compat] Error 2 make[1]: *** [_module_/home/marco/compat-wireless-3.1.1-1] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.2.0-31-generic' make: *** [modules] Error 2 To fix that error I added #include <linux/kconfig.h> to /usr/src/linux-headers-3.2.0-31-generic/include/linux/netdevice.h but now I'm getting something else make make -C /lib/modules/3.2.0-31-generic/build M=/home/marco/compat-wireless-3.1.1-1 modules make[1]: Entering directory `/usr/src/linux-headers-3.2.0-31-generic' CC [M] /home/marco/compat-wireless-3.1.1-1/compat/main.o LD [M] /home/marco/compat-wireless-3.1.1-1/compat/compat.o CC [M] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.o In file included from /home/marco/compat-wireless-3.1.1-1/include/linux/bcma/bcma.h:9:0, from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/bcma_private.h:8, from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:8: /home/marco/compat-wireless-3.1.1-1/include/linux/ssb/ssb.h: In function ‘ssb_driver_register’: /home/marco/compat-wireless-3.1.1-1/include/linux/ssb/ssb.h:236:36: error: ‘THIS_MODULE’ undeclared (first use in this function) /home/marco/compat-wireless-3.1.1-1/include/linux/ssb/ssb.h:236:36: note: each undeclared identifier is reported only once for each function it appears in In file included from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/bcma_private.h:8:0, from /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:8: /home/marco/compat-wireless-3.1.1-1/include/linux/bcma/bcma.h: In function ‘bcma_driver_register’: /home/marco/compat-wireless-3.1.1-1/include/linux/bcma/bcma.h:170:37: error: ‘THIS_MODULE’ undeclared (first use in this function) /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c: At top level: /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:12:20: error: expected declaration specifiers or ‘...’ before string constant /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:13:16: error: expected declaration specifiers or ‘...’ before string constant /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:182:1: warning: data definition has no type or storage class [enabled by default] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:182:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’ [-Wimplicit-int] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:182:1: warning: parameter names (without types) in function declaration [enabled by default] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:188:1: warning: data definition has no type or storage class [enabled by default] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:188:1: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’ [-Wimplicit-int] /home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.c:188:1: warning: parameter names (without types) in function declaration [enabled by default] make[3]: *** [/home/marco/compat-wireless-3.1.1-1/drivers/bcma/main.o] Error 1 make[2]: *** [/home/marco/compat-wireless-3.1.1-1/drivers/bcma] Error 2 make[1]: *** [_module_/home/marco/compat-wireless-3.1.1-1] Error 2 make[1]: Leaving directory `/usr/src/linux-headers-3.2.0-31-generic' make: *** [modules] Error 2 Any suggestion what to try next?

  Read the article

• LPR printing in Ubuntu

  - by Ben

  I'm trying to set up printing to a networked LPR printer, but I can't seem to make it work. The connexion information that IT gives is: Print Spooler: printing.domain.edu Printer Name: PrinterName Print port: 515 Bidirectional: Disabled It's an HP LaserJet p4015x, and I'm using the "HP LaserJet p4015x, hpcups 3.10.6 (color, 2-sided printing)" driver, according to CUPS. I have tried installing via the CUPS admin interface as lpd://printing.domain.edu:515/PrinterName, lpd://printing.domain.edu/PrinterName, and http://printing.domain.edu:515/PrinterName, and none of these has worked (i.e. test pages show up as "stopped").

  Read the article

• 'Make' command compiling errors

  - by G_T

  Im trying to locally install a program which is written in C++. I have downloaded the program and am attempting to use the "make" command to compile the program as the programs instructions dictate. However when I do I get this error: /usr/include/stdc-predef.h:30:26: fatal error: bits/predefs.h: No such file or directory compilation terminated. Looking around on the internet some people seem to address this problem by sudo apt-get install libc6-dev-i386 I checked to see if this package was installed and it was not. When I try to install it I get E: Unable to locate package libc6-dev-i386 I have already run sudo apt get update Im sure this is a rookie question but any help is appreciated, I'm running 13.10 32-bit. UPDATE: I've tried other suggestions I've found on similar error. All I have managed is a different but similar error. Here is what I get. Geoffrey@Geoffrey-Latitude-E6400:/usr/local/src/trinityrnaseq_r2013_08_14$ make Using gnu compiler for Inchworm and Chrysalis cd Inchworm && (test -e configure || autoreconf) \ && ./configure --prefix=`pwd` && make install checking for a BSD-compatible install... /usr/bin/install -c checking whether build environment is sane... yes checking for gawk... no checking for mawk... mawk checking whether make sets $(MAKE)... yes checking for g++... g++ checking for C++ compiler default output file name... a.out checking whether the C++ compiler works... yes checking whether we are cross compiling... no checking for suffix of executables... checking for suffix of object files... o checking whether we are using the GNU C++ compiler... yes checking whether g++ accepts -g... yes checking for style of include used by make... GNU checking dependency style of g++... gcc3 checking for library containing cos... none required configure: creating ./config.status config.status: creating Makefile config.status: creating src/Makefile config.status: creating config.h config.status: config.h is unchanged config.status: executing depfiles commands make[1]: Entering directory `/usr/local/src/trinityrnaseq_r2013_08_14/Inchworm' Making install in src make[2]: Entering directory `/usr/local/src/trinityrnaseq_r2013_08_14/Inchworm/src' if g++ -DHAVE_CONFIG_H -I. -I. -I.. -pedantic -fopenmp -Wall -Wextra -Wno-long-long -Wno-deprecated -m64 -g -O2 -MT Fasta_entry.o -MD -MP -MF ".deps/Fasta_entry.Tpo" -c -o Fasta_entry.o Fasta_entry.cpp; \ then mv -f ".deps/Fasta_entry.Tpo" ".deps/Fasta_entry.Po"; else rm -f ".deps/Fasta_entry.Tpo"; exit 1; fi In file included from Fasta_entry.hpp:4:0, from Fasta_entry.cpp:1: /usr/include/c++/4.8/string:38:28: fatal error: bits/c++config.h: No such file or directory #include <bits/c++config.h> ^ compilation terminated. make[2]: *** [Fasta_entry.o] Error 1 make[2]: Leaving directory `/usr/local/src/trinityrnaseq_r2013_08_14/Inchworm/src' make[1]: *** [install-recursive] Error 1 make[1]: Leaving directory `/usr/local/src/trinityrnaseq_r2013_08_14/Inchworm' make: *** [inchworm] Error 2

  Read the article

• Installing Ubuntu 12.10 on Mac Mini (End 2009)

  - by Till Lange

  I am trying to installing Ubuntu 12.10 on my Mac Mini (End 2009). This sounds like a often asked question and I all ready read lots of stuff about it, but now I am confused. While some people say, there are heavy problems by installing Ubuntu on a Mac Mini, such as components (like Sound card, graphic card, …) don't work very well, others say, that it should work perfectly fine. I figured out that installing UBNTU on a Mac isn't as easy (can't just downld the .iso and use unetboot, …) as it is on a PC. So, is it possible to install Ubuntu 12.10 on a Mac Mini 2009 (end), so everything works well?

  Read the article

• How to increase screen resolution in Hyper-V

  - by Saad

  I am using Ubuntu 12.04 on Hyper-V in windows 8. I want to increase the resolution so that Ubuntu window can occupy my whole screen. Does anyone have any idea of how it can be done ? I found one solution http://nramkumar.org/tech/blog/2013/05/04/ubuntu-under-hyper-v-how-to-overcome-screen-resolution-issue/, I have installed OpenSSH server on Ubuntu and Xming and Putty on windows. I am not sure what hostname to use to connect to Ubuntu (running in Hyper-V), using [email protected] or username@localhost in the hostname field returns error "Network error:connection refused". Can someone help me figure out what i am doing wrong ?

  Read the article

• 12.04 upgrade broke grub? (not wubi related)

  - by kaare

  I just updated from 11.10 to 12.04, with no major problems (it took a while to get past a request to restart ssh, mysql and some other services, but I did no fiddling by myself, everything was done by the installer). However, after restarting, grub can't do anything. Picking the new linux installation (first entry), I just get error: no such partition error: no such partition error: no such partition and picking the recovery-version just gives 5 lines instead of 3. I have windows 7 installed on a different drive, and can run it by booting from that drive instead. Picking it from the grub menu gives the same error as above (can't remember how many lines, though). I'll be honest and say that I don't remember if win 7 could be booted from grub before the update, though. In short, nothing on the grub menu works. any solutions? The grub menu changed appearance - before it was on a purple background, small letters, now it's white-on-black, big letters, looking very basic. The original installation was from a usb-drive, and I hadn't heard about wubi until I started googling this problem, so I doubt there's any connection. I really hope there are some grub-savvy people out there :) EDIT: ok. so, I made a bootable usb, and am running from that right now. when I ran the bootinfoscript, it warned me that "gawk" could not be found, using "busybox awk" instead. This may lead to unreliable results. just so you know. The contents of RESULTS.txt are: Boot Info Script 0.61 [1 April 2012] ============================= Boot Info Summary: =============================== => Windows is installed in the MBR of /dev/sda. => Grub2 (v1.99) is installed in the MBR of /dev/sdb and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos3)/boot/grub on this drive. => Syslinux MBR (4.04 and higher) is installed in the MBR of /dev/sdc. sda1: __________________________________________ File system: vfat Boot sector type: Dell Utility: FAT16 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /DELLBIO.BIN /DELLRMK.BIN /COMMAND.COM sda2: __________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sda3: __________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe sda4: __________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sda5: __________________________________________ File system: vfat Boot sector type: Windows 7: FAT32 Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows XP Boot files: /boot.ini /bootmgr /ntldr /NTDETECT.COM sdb1: __________________________________________ File system: ntfs Boot sector type: Windows XP: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: sdb2: __________________________________________ File system: swap Boot sector type: - Boot sector info: sdb3: __________________________________________ File system: ext4 Boot sector type: Grub2 (v1.99) Boot sector info: Grub2 (v1.99) is installed in the boot sector of sdb3 and looks at sector 375893584 of the same hard drive for core.img. core.img is at this location and looks for (,msdos3)/boot/grub on this drive. Operating System: Ubuntu 12.04 LTS Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb4: __________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Boot files: sdc1: __________________________________________ File system: ntfs Boot sector type: SYSLINUX 4.06 4.06-pre1 Boot sector info: Syslinux looks at sector 4649656 of /dev/sdc1 for its second stage. SYSLINUX is installed in the directory. The integrity check of the ADV area failed. No errors found in the Boot Parameter Block. Operating System: Boot files: /boot/grub/grub.cfg /syslinux/syslinux.cfg /ldlinux.sys ============================ Drive/Partition Info: ============================= Drive: sda _______________________________________ Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 63 240,974 240,912 de Dell Utility /dev/sda2 241,664 21,213,183 20,971,520 7 NTFS / exFAT / HPFS /dev/sda3 * 21,213,184 483,151,863 461,938,680 7 NTFS / exFAT / HPFS /dev/sda4 483,151,872 488,394,751 5,242,880 f W95 Extended (LBA) /dev/sda5 483,153,920 488,394,751 5,240,832 dd Dell Media Direct Drive: sdb _______________________________________ Disk /dev/sdb: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders, total 488397168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdb1 63 345,886,749 345,886,687 7 NTFS / exFAT / HPFS /dev/sdb2 345,888,768 361,510,911 15,622,144 82 Linux swap / Solaris /dev/sdb3 * 361,510,912 390,807,786 29,296,875 83 Linux /dev/sdb4 390,809,600 488,394,751 97,585,152 83 Linux Drive: sdc _______________________________________ Disk /dev/sdc: 8015 MB, 8015282176 bytes 255 heads, 63 sectors/track, 974 cylinders, total 15654848 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdc1 * 2,048 15,652,863 15,650,816 7 NTFS / exFAT / HPFS "blkid" output: ____________________________________ Device UUID TYPE LABEL /dev/loop0 squashfs /dev/sda1 07D8-0411 vfat DellUtility /dev/sda2 E2765BBC765B9061 ntfs RECOVERY /dev/sda3 98DC5E54DC5E2D2E ntfs OS /dev/sda5 7061-9DF5 vfat MEDIADIRECT /dev/sdb1 01CBBB4C3374C3B0 ntfs Data1 /dev/sdb2 1ca45f3f-f888-43d1-8137-02699597189a swap /dev/sdb3 6bc1b599-ad4b-403c-a155-a5bc81211f5e ext4 /dev/sdb4 58e2b257-8608-4b11-b20b-dc162bb80b62 ext4 /dev/sdc1 0C02B64402B63316 ntfs PENDRIVE ================================ Mount points: ================================= Device Mount_Point Type Options /dev/loop0 /rofs squashfs (ro,noatime) /dev/sdb4 /media/58e2b257-8608-4b11-b20b-dc162bb80b62 ext4 (rw,nosuid,nodev,uhelper=udisks) /dev/sdc1 /cdrom fuseblk (rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other,blksize=4096) ================================ sda5/boot.ini: ================================ [boot loader] timeout=0 default=multi(0)disk(0)rdisk(0)partition(1)\WINDOWS [operating systems] multi(0)disk(0)rdisk(0)partition(1)\WINDOWS="Microsoft Windows XP Embedded" /fastdetect /KERNEL=NTOSBOOT.EXE /maxmem=1024 =========================== sdb3/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e set locale_dir=($root)/boot/grub/locale set lang=en_US insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="$1" if [ "$1" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ ${recordfail} != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "$linux_gfx_mode" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.2.0-24-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e linux /boot/vmlinuz-3.2.0-24-generic root=UUID=6bc1b599-ad4b-403c-a155-a5bc81211f5e ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-24-generic } menuentry 'Ubuntu, with Linux 3.2.0-24-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e echo 'Loading Linux 3.2.0-24-generic ...' linux /boot/vmlinuz-3.2.0-24-generic root=UUID=6bc1b599-ad4b-403c-a155-a5bc81211f5e ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.2.0-24-generic } submenu "Previous Linux versions" { menuentry 'Ubuntu, with Linux 3.0.0-19-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e linux /boot/vmlinuz-3.0.0-19-generic root=UUID=6bc1b599-ad4b-403c-a155-a5bc81211f5e ro quiet splash $vt_handoff initrd /boot/initrd.img-3.0.0-19-generic } menuentry 'Ubuntu, with Linux 3.0.0-19-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e echo 'Loading Linux 3.0.0-19-generic ...' linux /boot/vmlinuz-3.0.0-19-generic root=UUID=6bc1b599-ad4b-403c-a155-a5bc81211f5e ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.0.0-19-generic } } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd1,msdos3)' search --no-floppy --fs-uuid --set=root 6bc1b599-ad4b-403c-a155-a5bc81211f5e linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sda3)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos3)' search --no-floppy --fs-uuid --set=root 98DC5E54DC5E2D2E chainloader +1 } menuentry "Microsoft Windows XP Embedded (on /dev/sda5)" --class windows --class os { insmod part_msdos insmod fat set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root 7061-9DF5 drivemap -s (hd0) ${root} chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### =============================== sdb3/etc/fstab: ================================ # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sdb3 during installation UUID=6bc1b599-ad4b-403c-a155-a5bc81211f5e / ext4 errors=remount-ro 0 1 # /home was on /dev/sdb4 during installation UUID=58e2b257-8608-4b11-b20b-dc162bb80b62 /home ext4 defaults,user_xattr 0 2 # swap was on /dev/sdb2 during installation UUID=1ca45f3f-f888-43d1-8137-02699597189a none swap sw 0 0 =================== sdb3: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) = boot/grub/core.img 1 = boot/grub/grub.cfg 1 = boot/initrd.img-3.0.0-19-generic 2 = boot/initrd.img-3.2.0-24-generic 2 = boot/vmlinuz-3.0.0-19-generic 2 = boot/vmlinuz-3.2.0-24-generic 1 = vmlinuz 1 = vmlinuz.old 2 =========================== sdc1/boot/grub/grub.cfg: =========================== if loadfont /boot/grub/font.pf2 ; then set gfxmode=auto insmod efi_gop insmod efi_uga insmod gfxterm terminal_output gfxterm fi set menu_color_normal=white/black set menu_color_highlight=black/light-gray menuentry "Try Ubuntu without installing" { set gfxpayload=keep linux /casper/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper quiet splash -- initrd /casper/initrd.lz } menuentry "Install Ubuntu" { set gfxpayload=keep linux /casper/vmlinuz file=/cdrom/preseed/ubuntu.seed boot=casper only-ubiquity quiet splash -- initrd /casper/initrd.lz } menuentry "Check disc for defects" { set gfxpayload=keep linux /casper/vmlinuz boot=casper integrity-check quiet splash -- initrd /casper/initrd.lz } ========================= sdc1/syslinux/syslinux.cfg: ========================== # D-I config version 2.0 include menu.cfg default vesamenu.c32 prompt 0 timeout 50 # If you would like to use the new menu and be presented with the option to install or run from USB at startup, remove # from the following line. This line was commented out (by request of many) to allow the old menu to be presented and to enable booting straight into the Live Environment! # ui gfxboot bootlogo =================== sdc1: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) ?? = ?? boot/grub/grub.cfg 0 ================= sdc1: Location of files loaded by Syslinux: ================== GiB - GB File Fragment(s) ?? = ?? ldlinux.sys 1 ?? = ?? syslinux/chain.c32 1 ?? = ?? syslinux/gfxboot.c32 1 ?? = ?? syslinux/syslinux.cfg 0 ?? = ?? syslinux/vesamenu.c32 1 ============== sdc1: Version of COM32(R) files used by Syslinux: =============== syslinux/chain.c32 : COM32R module (v4.xx) syslinux/gfxboot.c32 : COM32R module (v4.xx) syslinux/vesamenu.c32 : COM32R module (v4.xx) =============================== StdErr Messages: =============================== xz: (stdin): Compressed data is corrupt xz: (stdin): Compressed data is corrupt awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in ./bootinfoscript: line 1646: [: 2.73495e+09: integer expression expected

  Read the article

• Merging /boot and rearranging grub2 entries

  - by Tobias Kienzler

  I have used 10.10 and now for testing purposes installed 10.04 to a separate partition. 10.10 is currently on a single partition, while for 10.04 I decided to separate /boot to a third partition. Now my questions: How can I move and merge 10.10's /boot on the new /boot partition What do I have to modify to rearrange the (automatic) entries? How can I have the entries contain the distribution name to reduce confusion? How can I make sure the grub configuration stays identical when either distribution updates?

  Read the article

• Backtrack installation interrupted once, installed another time

  - by Bernard

  I installed Backtrack 5 from a Live CD yesterday and while installing, i closed my laptop to let it run while I sleep. But then I remembered my friend told me the plastic of his computer melted this way, so i opened it again. It put it on power save, and somehow the installation was interrupted. The day after, I tried again and this time it worked. Now, I have a GRUB Menu With Win7 and twice the Ubuntu + Safe mode or whatever it's called. How can I remove the failed installation without deleting Win7 or the successful installation? Normally I would use EasyBCD and delete the partitions, but this time I couldn't start Backtrack then. Thanks in advance Bernard

  Read the article

• Errors when installing Open Office

  - by user109036

  I followed the first set of instructions on this page to install Open Office: How to install Open Office? However, the last step which says to change the CHMOD of a folder, I got an error saying that the directory does not exist. Open Office now appears in my Ubuntu start menu, but clicking on it does nothing. I tried a reboot. Below is what I could copy from my terminal. I am running the latest Ubuntu. I have not uninstalled Libreoffice as suggested somewhere. The reason is that in the Ubuntu software centre, Libre office appears to be made up of several components and I don't know which ones to remove (or all maybe?). They are Libreoffice Draw, Math, Writer, Calc. After this operation, 480 MB of additional disk space will be used. Do you want to continue [Y/n]? y Get:1 http://gb.archive.ubuntu.com/ubuntu/ quantal-updates/universe openjdk-6-jre-lib all 6b24-1.11.5-0ubuntu1~12.10.1 [6,135 kB] Get:2 http://ppa.launchpad.net/upubuntu-com/office/ubuntu/ quantal/main openoffice amd64 3.4~oneiric [321 MB] Get:3 http://gb.archive.ubuntu.com/ubuntu/ quantal/main ca-certificates-java all 20120721 [13.2 kB] Get:4 http://gb.archive.ubuntu.com/ubuntu/ quantal/main tzdata-java all 2012e-0ubuntu2 [140 kB] Get:5 http://gb.archive.ubuntu.com/ubuntu/ quantal/main java-common all 0.43ubuntu3 [61.7 kB] Get:6 http://gb.archive.ubuntu.com/ubuntu/ quantal-updates/universe openjdk-6-jre-headless amd64 6b24-1.11.5-0ubuntu1~12.10.1 [25.4 MB] Get:7 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libgif4 amd64 4.1.6-9.1ubuntu1 [31.3 kB] Get:8 http://gb.archive.ubuntu.com/ubuntu/ quantal-updates/universe openjdk-6-jre amd64 6b24-1.11.5-0ubuntu1~12.10.1 [234 kB] Get:9 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libatk-wrapper-java all 0.30.4-0ubuntu4 [29.8 kB] Get:10 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libatk-wrapper-java-jni amd64 0.30.4-0ubuntu4 [31.1 kB] Get:11 http://gb.archive.ubuntu.com/ubuntu/ quantal/main xorg-sgml-doctools all 1:1.10-1 [12.0 kB] Get:12 http://gb.archive.ubuntu.com/ubuntu/ quantal/main x11proto-core-dev all 7.0.23-1 [744 kB] Get:13 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libice-dev amd64 2:1.0.8-2 [57.6 kB] Get:14 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libpthread-stubs0 amd64 0.3-3 [3,258 B] Get:15 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libpthread-stubs0-dev amd64 0.3-3 [2,866 B] Get:16 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libsm-dev amd64 2:1.2.1-2 [19.9 kB] Get:17 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libxau-dev amd64 1:1.0.7-1 [10.2 kB] Get:18 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libxdmcp-dev amd64 1:1.1.1-1 [26.9 kB] Get:19 http://gb.archive.ubuntu.com/ubuntu/ quantal/main x11proto-input-dev all 2.2-1 [133 kB] Get:20 http://gb.archive.ubuntu.com/ubuntu/ quantal/main x11proto-kb-dev all 1.0.6-2 [269 kB] Get:21 http://gb.archive.ubuntu.com/ubuntu/ quantal/main xtrans-dev all 1.2.7-1 [84.3 kB] Get:22 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libxcb1-dev amd64 1.8.1-1ubuntu1 [82.6 kB] Get:23 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libx11-dev amd64 2:1.5.0-1 [912 kB] Get:24 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libx11-doc all 2:1.5.0-1 [2,460 kB] Get:25 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libxt-dev amd64 1:1.1.3-1 [492 kB] Get:26 http://gb.archive.ubuntu.com/ubuntu/ quantal/main ttf-dejavu-extra all 2.33-2ubuntu1 [3,420 kB] Get:27 http://gb.archive.ubuntu.com/ubuntu/ quantal-updates/universe icedtea-6-jre-cacao amd64 6b24-1.11.5-0ubuntu1~12.10.1 [417 kB] Get:28 http://gb.archive.ubuntu.com/ubuntu/ quantal-updates/universe icedtea-6-jre-jamvm amd64 6b24-1.11.5-0ubuntu1~12.10.1 [581 kB] Get:29 http://gb.archive.ubuntu.com/ubuntu/ quantal-updates/main icedtea-netx-common all 1.3-1ubuntu1.1 [617 kB] Get:30 http://gb.archive.ubuntu.com/ubuntu/ quantal-updates/main icedtea-netx amd64 1.3-1ubuntu1.1 [16.2 kB] Get:31 http://gb.archive.ubuntu.com/ubuntu/ quantal-updates/universe openjdk-6-jdk amd64 6b24-1.11.5-0ubuntu1~12.10.1 [11.1 MB] Fetched 374 MB in 9min 18s (671 kB/s) Extract templates from packages: 100% Selecting previously unselected package openjdk-6-jre-lib. (Reading database ... 143191 files and directories currently installed.) Unpacking openjdk-6-jre-lib (from .../openjdk-6-jre-lib_6b24-1.11.5-0ubuntu1~12.10.1_all.deb) ... Selecting previously unselected package ca-certificates-java. Unpacking ca-certificates-java (from .../ca-certificates-java_20120721_all.deb) ... Selecting previously unselected package tzdata-java. Unpacking tzdata-java (from .../tzdata-java_2012e-0ubuntu2_all.deb) ... Selecting previously unselected package java-common. Unpacking java-common (from .../java-common_0.43ubuntu3_all.deb) ... Selecting previously unselected package openjdk-6-jre-headless:amd64. Unpacking openjdk-6-jre-headless:amd64 (from .../openjdk-6-jre-headless_6b24-1.11.5-0ubuntu1~12.10.1_amd64.deb) ... Selecting previously unselected package libgif4:amd64. Unpacking libgif4:amd64 (from .../libgif4_4.1.6-9.1ubuntu1_amd64.deb) ... Selecting previously unselected package openjdk-6-jre:amd64. Unpacking openjdk-6-jre:amd64 (from .../openjdk-6-jre_6b24-1.11.5-0ubuntu1~12.10.1_amd64.deb) ... Selecting previously unselected package libatk-wrapper-java. Unpacking libatk-wrapper-java (from .../libatk-wrapper-java_0.30.4-0ubuntu4_all.deb) ... Selecting previously unselected package libatk-wrapper-java-jni:amd64. Unpacking libatk-wrapper-java-jni:amd64 (from .../libatk-wrapper-java-jni_0.30.4-0ubuntu4_amd64.deb) ... Selecting previously unselected package xorg-sgml-doctools. Unpacking xorg-sgml-doctools (from .../xorg-sgml-doctools_1%3a1.10-1_all.deb) ... Selecting previously unselected package x11proto-core-dev. Unpacking x11proto-core-dev (from .../x11proto-core-dev_7.0.23-1_all.deb) ... Selecting previously unselected package libice-dev:amd64. Unpacking libice-dev:amd64 (from .../libice-dev_2%3a1.0.8-2_amd64.deb) ... Selecting previously unselected package libpthread-stubs0:amd64. Unpacking libpthread-stubs0:amd64 (from .../libpthread-stubs0_0.3-3_amd64.deb) ... Selecting previously unselected package libpthread-stubs0-dev:amd64. Unpacking libpthread-stubs0-dev:amd64 (from .../libpthread-stubs0-dev_0.3-3_amd64.deb) ... Selecting previously unselected package libsm-dev:amd64. Unpacking libsm-dev:amd64 (from .../libsm-dev_2%3a1.2.1-2_amd64.deb) ... Selecting previously unselected package libxau-dev:amd64. Unpacking libxau-dev:amd64 (from .../libxau-dev_1%3a1.0.7-1_amd64.deb) ... Selecting previously unselected package libxdmcp-dev:amd64. Unpacking libxdmcp-dev:amd64 (from .../libxdmcp-dev_1%3a1.1.1-1_amd64.deb) ... Selecting previously unselected package x11proto-input-dev. Unpacking x11proto-input-dev (from .../x11proto-input-dev_2.2-1_all.deb) ... Selecting previously unselected package x11proto-kb-dev. Unpacking x11proto-kb-dev (from .../x11proto-kb-dev_1.0.6-2_all.deb) ... Selecting previously unselected package xtrans-dev. Unpacking xtrans-dev (from .../xtrans-dev_1.2.7-1_all.deb) ... Selecting previously unselected package libxcb1-dev:amd64. Unpacking libxcb1-dev:amd64 (from .../libxcb1-dev_1.8.1-1ubuntu1_amd64.deb) ... Selecting previously unselected package libx11-dev:amd64. Unpacking libx11-dev:amd64 (from .../libx11-dev_2%3a1.5.0-1_amd64.deb) ... Selecting previously unselected package libx11-doc. Unpacking libx11-doc (from .../libx11-doc_2%3a1.5.0-1_all.deb) ... Selecting previously unselected package libxt-dev:amd64. Unpacking libxt-dev:amd64 (from .../libxt-dev_1%3a1.1.3-1_amd64.deb) ... Selecting previously unselected package ttf-dejavu-extra. Unpacking ttf-dejavu-extra (from .../ttf-dejavu-extra_2.33-2ubuntu1_all.deb) ... Selecting previously unselected package icedtea-6-jre-cacao:amd64. Unpacking icedtea-6-jre-cacao:amd64 (from .../icedtea-6-jre-cacao_6b24-1.11.5-0ubuntu1~12.10.1_amd64.deb) ... Selecting previously unselected package icedtea-6-jre-jamvm:amd64. Unpacking icedtea-6-jre-jamvm:amd64 (from .../icedtea-6-jre-jamvm_6b24-1.11.5-0ubuntu1~12.10.1_amd64.deb) ... Selecting previously unselected package icedtea-netx-common. Unpacking icedtea-netx-common (from .../icedtea-netx-common_1.3-1ubuntu1.1_all.deb) ... Selecting previously unselected package icedtea-netx:amd64. Unpacking icedtea-netx:amd64 (from .../icedtea-netx_1.3-1ubuntu1.1_amd64.deb) ... Selecting previously unselected package openjdk-6-jdk:amd64. Unpacking openjdk-6-jdk:amd64 (from .../openjdk-6-jdk_6b24-1.11.5-0ubuntu1~12.10.1_amd64.deb) ... Selecting previously unselected package openoffice. Unpacking openoffice (from .../openoffice_3.4~oneiric_amd64.deb) ... Processing triggers for doc-base ... Processing 2 added doc-base files... Processing triggers for man-db ... Processing triggers for desktop-file-utils ... Processing triggers for bamfdaemon ... Rebuilding /usr/share/applications/bamf.index... Processing triggers for gnome-menus ... Processing triggers for hicolor-icon-theme ... Processing triggers for fontconfig ... Processing triggers for gnome-icon-theme ... Processing triggers for shared-mime-info ... Setting up tzdata-java (2012e-0ubuntu2) ... Setting up java-common (0.43ubuntu3) ... Setting up libgif4:amd64 (4.1.6-9.1ubuntu1) ... Setting up xorg-sgml-doctools (1:1.10-1) ... Setting up x11proto-core-dev (7.0.23-1) ... Setting up libice-dev:amd64 (2:1.0.8-2) ... Setting up libpthread-stubs0:amd64 (0.3-3) ... Setting up libpthread-stubs0-dev:amd64 (0.3-3) ... Setting up libsm-dev:amd64 (2:1.2.1-2) ... Setting up libxau-dev:amd64 (1:1.0.7-1) ... Setting up libxdmcp-dev:amd64 (1:1.1.1-1) ... Setting up x11proto-input-dev (2.2-1) ... Setting up x11proto-kb-dev (1.0.6-2) ... Setting up xtrans-dev (1.2.7-1) ... Setting up libxcb1-dev:amd64 (1.8.1-1ubuntu1) ... Setting up libx11-dev:amd64 (2:1.5.0-1) ... Setting up libx11-doc (2:1.5.0-1) ... Setting up libxt-dev:amd64 (1:1.1.3-1) ... Setting up ttf-dejavu-extra (2.33-2ubuntu1) ... Setting up icedtea-netx-common (1.3-1ubuntu1.1) ... Setting up openjdk-6-jre-lib (6b24-1.11.5-0ubuntu1~12.10.1) ... Setting up openjdk-6-jre-headless:amd64 (6b24-1.11.5-0ubuntu1~12.10.1) ... update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/java to provide /usr/bin/java (java) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/keytool to provide /usr/bin/keytool (keytool) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/pack200 to provide /usr/bin/pack200 (pack200) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/rmid to provide /usr/bin/rmid (rmid) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/rmiregistry to provide /usr/bin/rmiregistry (rmiregistry) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/unpack200 to provide /usr/bin/unpack200 (unpack200) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/orbd to provide /usr/bin/orbd (orbd) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/servertool to provide /usr/bin/servertool (servertool) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/tnameserv to provide /usr/bin/tnameserv (tnameserv) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/lib/jexec to provide /usr/bin/jexec (jexec) in auto mode Setting up ca-certificates-java (20120721) ... Adding debian:Deutsche_Telekom_Root_CA_2.pem Adding debian:Comodo_Trusted_Services_root.pem Adding debian:Certum_Trusted_Network_CA.pem Adding debian:thawte_Primary_Root_CA_-_G2.pem Adding debian:UTN_USERFirst_Hardware_Root_CA.pem Adding debian:AddTrust_Low-Value_Services_Root.pem Adding debian:Microsec_e-Szigno_Root_CA.pem Adding debian:SwissSign_Silver_CA_-_G2.pem Adding debian:ComSign_Secured_CA.pem Adding debian:Buypass_Class_2_CA_1.pem Adding debian:Verisign_Class_1_Public_Primary_Certification_Authority_-_G3.pem Adding debian:Certum_Root_CA.pem Adding debian:AddTrust_External_Root.pem Adding debian:Chambers_of_Commerce_Root_-_2008.pem Adding debian:Starfield_Root_Certificate_Authority_-_G2.pem Adding debian:Verisign_Class_1_Public_Primary_Certification_Authority_-_G2.pem Adding debian:Visa_eCommerce_Root.pem Adding debian:Digital_Signature_Trust_Co._Global_CA_3.pem Adding debian:AC_Raíz_Certicámara_S.A..pem Adding debian:NetLock_Arany_=Class_Gold=_Fotanúsítvány.pem Adding debian:Taiwan_GRCA.pem Adding debian:Camerfirma_Chambers_of_Commerce_Root.pem Adding debian:Juur-SK.pem Adding debian:Entrust.net_Premium_2048_Secure_Server_CA.pem Adding debian:XRamp_Global_CA_Root.pem Adding debian:Security_Communication_RootCA2.pem Adding debian:AddTrust_Qualified_Certificates_Root.pem Adding debian:NetLock_Qualified_=Class_QA=_Root.pem Adding debian:TC_TrustCenter_Class_2_CA_II.pem Adding debian:DST_ACES_CA_X6.pem Adding debian:thawte_Primary_Root_CA.pem Adding debian:thawte_Primary_Root_CA_-_G3.pem Adding debian:GeoTrust_Universal_CA_2.pem Adding debian:ACEDICOM_Root.pem Adding debian:Security_Communication_EV_RootCA1.pem Adding debian:America_Online_Root_Certification_Authority_2.pem Adding debian:TC_TrustCenter_Universal_CA_I.pem Adding debian:SwissSign_Platinum_CA_-_G2.pem Adding debian:Global_Chambersign_Root_-_2008.pem Adding debian:SecureSign_RootCA11.pem Adding debian:GeoTrust_Global_CA_2.pem Adding debian:Buypass_Class_3_CA_1.pem Adding debian:Baltimore_CyberTrust_Root.pem Adding debian:UbuntuOne-Go_Daddy_Class_2_CA.pem Adding debian:Equifax_Secure_eBusiness_CA_1.pem Adding debian:SwissSign_Gold_CA_-_G2.pem Adding debian:AffirmTrust_Premium_ECC.pem Adding debian:TC_TrustCenter_Universal_CA_III.pem Adding debian:ca.pem Adding debian:Verisign_Class_3_Public_Primary_Certification_Authority_-_G2.pem Adding debian:NetLock_Express_=Class_C=_Root.pem Adding debian:VeriSign_Class_3_Public_Primary_Certification_Authority_-_G5.pem Adding debian:Firmaprofesional_Root_CA.pem Adding debian:Comodo_Secure_Services_root.pem Adding debian:cacert.org.pem Adding debian:GeoTrust_Primary_Certification_Authority.pem Adding debian:RSA_Security_2048_v3.pem Adding debian:Staat_der_Nederlanden_Root_CA.pem Adding debian:Cybertrust_Global_Root.pem Adding debian:DigiCert_High_Assurance_EV_Root_CA.pem Adding debian:TDC_OCES_Root_CA.pem Adding debian:A-Trust-nQual-03.pem Adding debian:Equifax_Secure_CA.pem Adding debian:Digital_Signature_Trust_Co._Global_CA_1.pem Adding debian:GeoTrust_Global_CA.pem Adding debian:Starfield_Class_2_CA.pem Adding debian:ApplicationCA_-_Japanese_Government.pem Adding debian:Swisscom_Root_CA_1.pem Adding debian:Verisign_Class_2_Public_Primary_Certification_Authority_-_G2.pem Adding debian:Camerfirma_Global_Chambersign_Root.pem Adding debian:QuoVadis_Root_CA_3.pem Adding debian:QuoVadis_Root_CA.pem Adding debian:Comodo_AAA_Services_root.pem Adding debian:ComSign_CA.pem Adding debian:AddTrust_Public_Services_Root.pem Adding debian:DigiCert_Assured_ID_Root_CA.pem Adding debian:UTN_DATACorp_SGC_Root_CA.pem Adding debian:CA_Disig.pem Adding debian:E-Guven_Kok_Elektronik_Sertifika_Hizmet_Saglayicisi.pem Adding debian:GlobalSign_Root_CA_-_R3.pem Adding debian:QuoVadis_Root_CA_2.pem Adding debian:Entrust_Root_Certification_Authority.pem Adding debian:GTE_CyberTrust_Global_Root.pem Adding debian:ValiCert_Class_1_VA.pem Adding debian:Autoridad_de_Certificacion_Firmaprofesional_CIF_A62634068.pem Adding debian:GeoTrust_Primary_Certification_Authority_-_G2.pem Adding debian:spi-ca-2003.pem Adding debian:America_Online_Root_Certification_Authority_1.pem Adding debian:AffirmTrust_Premium.pem Adding debian:Sonera_Class_1_Root_CA.pem Adding debian:Verisign_Class_2_Public_Primary_Certification_Authority_-_G3.pem Adding debian:Certplus_Class_2_Primary_CA.pem Adding debian:TURKTRUST_Certificate_Services_Provider_Root_2.pem Adding debian:Network_Solutions_Certificate_Authority.pem Adding debian:Go_Daddy_Class_2_CA.pem Adding debian:StartCom_Certification_Authority.pem Adding debian:Hongkong_Post_Root_CA_1.pem Adding debian:Hellenic_Academic_and_Research_Institutions_RootCA_2011.pem Adding debian:Thawte_Premium_Server_CA.pem Adding debian:EBG_Elektronik_Sertifika_Hizmet_Saglayicisi.pem Adding debian:TURKTRUST_Certificate_Services_Provider_Root_1.pem Adding debian:NetLock_Business_=Class_B=_Root.pem Adding debian:Microsec_e-Szigno_Root_CA_2009.pem Adding debian:DigiCert_Global_Root_CA.pem Adding debian:VeriSign_Class_3_Public_Primary_Certification_Authority_-_G4.pem Adding debian:IGC_A.pem Adding debian:TWCA_Root_Certification_Authority.pem Adding debian:S-TRUST_Authentication_and_Encryption_Root_CA_2005_PN.pem Adding debian:VeriSign_Universal_Root_Certification_Authority.pem Adding debian:DST_Root_CA_X3.pem Adding debian:Verisign_Class_1_Public_Primary_Certification_Authority.pem Adding debian:Root_CA_Generalitat_Valenciana.pem Adding debian:UTN_USERFirst_Email_Root_CA.pem Adding debian:ssl-cert-snakeoil.pem Adding debian:Starfield_Services_Root_Certificate_Authority_-_G2.pem Adding debian:GeoTrust_Primary_Certification_Authority_-_G3.pem Adding debian:Certinomis_-_Autorité_Racine.pem Adding debian:Verisign_Class_3_Public_Primary_Certification_Authority.pem Adding debian:TDC_Internet_Root_CA.pem Adding debian:UbuntuOne-ValiCert_Class_2_VA.pem Adding debian:AffirmTrust_Commercial.pem Adding debian:spi-cacert-2008.pem Adding debian:Izenpe.com.pem Adding debian:EC-ACC.pem Adding debian:Go_Daddy_Root_Certificate_Authority_-_G2.pem Adding debian:COMODO_ECC_Certification_Authority.pem Adding debian:CNNIC_ROOT.pem Adding debian:NetLock_Notary_=Class_A=_Root.pem Adding debian:Equifax_Secure_eBusiness_CA_2.pem Adding debian:Verisign_Class_3_Public_Primary_Certification_Authority_-_G3.pem Adding debian:Secure_Global_CA.pem Adding debian:UbuntuOne-Go_Daddy_CA.pem Adding debian:GeoTrust_Universal_CA.pem Adding debian:Wells_Fargo_Root_CA.pem Adding debian:Thawte_Server_CA.pem Adding debian:WellsSecure_Public_Root_Certificate_Authority.pem Adding debian:TC_TrustCenter_Class_3_CA_II.pem Adding debian:COMODO_Certification_Authority.pem Adding debian:Equifax_Secure_Global_eBusiness_CA.pem Adding debian:Security_Communication_Root_CA.pem Adding debian:GlobalSign_Root_CA_-_R2.pem Adding debian:TÜBITAK_UEKAE_Kök_Sertifika_Hizmet_Saglayicisi_-_Sürüm_3.pem Adding debian:Verisign_Class_4_Public_Primary_Certification_Authority_-_G3.pem Adding debian:certSIGN_ROOT_CA.pem Adding debian:RSA_Root_Certificate_1.pem Adding debian:ePKI_Root_Certification_Authority.pem Adding debian:Entrust.net_Secure_Server_CA.pem Adding debian:OISTE_WISeKey_Global_Root_GA_CA.pem Adding debian:Sonera_Class_2_Root_CA.pem Adding debian:Certigna.pem Adding debian:AffirmTrust_Networking.pem Adding debian:ValiCert_Class_2_VA.pem Adding debian:GlobalSign_Root_CA.pem Adding debian:Staat_der_Nederlanden_Root_CA_-_G2.pem Adding debian:SecureTrust_CA.pem done. Setting up openjdk-6-jre:amd64 (6b24-1.11.5-0ubuntu1~12.10.1) ... update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/policytool to provide /usr/bin/policytool (policytool) in auto mode Setting up libatk-wrapper-java (0.30.4-0ubuntu4) ... Setting up icedtea-6-jre-cacao:amd64 (6b24-1.11.5-0ubuntu1~12.10.1) ... Setting up icedtea-6-jre-jamvm:amd64 (6b24-1.11.5-0ubuntu1~12.10.1) ... Setting up icedtea-netx:amd64 (1.3-1ubuntu1.1) ... update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/javaws to provide /usr/bin/javaws (javaws) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/jre/bin/itweb-settings to provide /usr/bin/itweb-settings (itweb-settings) in auto mode update-alternatives: using /usr/lib/jvm/java-7-openjdk-amd64/jre/bin/javaws to provide /usr/bin/javaws (javaws) in auto mode update-alternatives: using /usr/lib/jvm/java-7-openjdk-amd64/jre/bin/itweb-settings to provide /usr/bin/itweb-settings (itweb-settings) in auto mode Setting up openjdk-6-jdk:amd64 (6b24-1.11.5-0ubuntu1~12.10.1) ... update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/appletviewer to provide /usr/bin/appletviewer (appletviewer) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/extcheck to provide /usr/bin/extcheck (extcheck) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/idlj to provide /usr/bin/idlj (idlj) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jar to provide /usr/bin/jar (jar) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jarsigner to provide /usr/bin/jarsigner (jarsigner) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/javac to provide /usr/bin/javac (javac) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/javadoc to provide /usr/bin/javadoc (javadoc) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/javah to provide /usr/bin/javah (javah) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/javap to provide /usr/bin/javap (javap) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jconsole to provide /usr/bin/jconsole (jconsole) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jdb to provide /usr/bin/jdb (jdb) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jhat to provide /usr/bin/jhat (jhat) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jinfo to provide /usr/bin/jinfo (jinfo) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jmap to provide /usr/bin/jmap (jmap) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jps to provide /usr/bin/jps (jps) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jrunscript to provide /usr/bin/jrunscript (jrunscript) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jsadebugd to provide /usr/bin/jsadebugd (jsadebugd) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jstack to provide /usr/bin/jstack (jstack) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jstat to provide /usr/bin/jstat (jstat) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/jstatd to provide /usr/bin/jstatd (jstatd) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/native2ascii to provide /usr/bin/native2ascii (native2ascii) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/rmic to provide /usr/bin/rmic (rmic) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/schemagen to provide /usr/bin/schemagen (schemagen) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/serialver to provide /usr/bin/serialver (serialver) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/wsgen to provide /usr/bin/wsgen (wsgen) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/wsimport to provide /usr/bin/wsimport (wsimport) in auto mode update-alternatives: using /usr/lib/jvm/java-6-openjdk-amd64/bin/xjc to provide /usr/bin/xjc (xjc) in auto mode Setting up openoffice (3.4~oneiric) ... Setting up libatk-wrapper-java-jni:amd64 (0.30.4-0ubuntu4) ... Processing triggers for libc-bin ... ldconfig deferred processing now taking place philip@X301-2:~$ sudo apt-get install libxrandr2:i386 libxinerama1:i386 Reading package lists... Done Building dependency tree Reading state information... Done The following package was automatically installed and is no longer required: linux-headers-3.5.0-17 Use 'apt-get autoremove' to remove it. The following extra packages will be installed: gcc-4.7-base:i386 libc6:i386 libgcc1:i386 libx11-6:i386 libxau6:i386 libxcb1:i386 libxdmcp6:i386 libxext6:i386 libxrender1:i386 Suggested packages: glibc-doc:i386 locales:i386 The following NEW packages will be installed gcc-4.7-base:i386 libc6:i386 libgcc1:i386 libx11-6:i386 libxau6:i386 libxcb1:i386 libxdmcp6:i386 libxext6:i386 libxinerama1:i386 libxrandr2:i386 libxrender1:i386 0 upgraded, 11 newly installed, 0 to remove and 93 not upgraded. Need to get 4,936 kB of archives. After this operation, 11.9 MB of additional disk space will be used. Do you want to continue [Y/n]? y Get:1 http://gb.archive.ubuntu.com/ubuntu/ quantal/main gcc-4.7-base i386 4.7.2-2ubuntu1 [15.5 kB] Get:2 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libc6 i386 2.15-0ubuntu20 [3,940 kB] Get:3 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libgcc1 i386 1:4.7.2-2ubuntu1 [53.5 kB] Get:4 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libxau6 i386 1:1.0.7-1 [8,582 B] Get:5 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libxdmcp6 i386 1:1.1.1-1 [13.1 kB] Get:6 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libxcb1 i386 1.8.1-1ubuntu1 [48.7 kB] Get:7 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libx11-6 i386 2:1.5.0-1 [776 kB] Get:8 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libxext6 i386 2:1.3.1-2 [33.9 kB] Get:9 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libxinerama1 i386 2:1.1.2-1 [8,118 B] Get:10 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libxrender1 i386 1:0.9.7-1 [20.1 kB] Get:11 http://gb.archive.ubuntu.com/ubuntu/ quantal/main libxrandr2 i386 2:1.4.0-1 [18.8 kB] Fetched 4,936 kB in 30s (161 kB/s) Preconfiguring packages ... Selecting previously unselected package gcc-4.7-base:i386. (Reading database ... 146005 files and directories currently installed.) Unpacking gcc-4.7-base:i386 (from .../gcc-4.7-base_4.7.2-2ubuntu1_i386.deb) ... Selecting previously unselected package libc6:i386. Unpacking libc6:i386 (from .../libc6_2.15-0ubuntu20_i386.deb) ... Selecting previously unselected package libgcc1:i386. Unpacking libgcc1:i386 (from .../libgcc1_1%3a4.7.2-2ubuntu1_i386.deb) ... Selecting previously unselected package libxau6:i386. Unpacking libxau6:i386 (from .../libxau6_1%3a1.0.7-1_i386.deb) ... Selecting previously unselected package libxdmcp6:i386. Unpacking libxdmcp6:i386 (from .../libxdmcp6_1%3a1.1.1-1_i386.deb) ... Selecting previously unselected package libxcb1:i386. Unpacking libxcb1:i386 (from .../libxcb1_1.8.1-1ubuntu1_i386.deb) ... Selecting previously unselected package libx11-6:i386. Unpacking libx11-6:i386 (from .../libx11-6_2%3a1.5.0-1_i386.deb) ... Selecting previously unselected package libxext6:i386. Unpacking libxext6:i386 (from .../libxext6_2%3a1.3.1-2_i386.deb) ... Selecting previously unselected package libxinerama1:i386. Unpacking libxinerama1:i386 (from .../libxinerama1_2%3a1.1.2-1_i386.deb) ... Selecting previously unselected package libxrender1:i386. Unpacking libxrender1:i386 (from .../libxrender1_1%3a0.9.7-1_i386.deb) ... Selecting previously unselected package libxrandr2:i386. Unpacking libxrandr2:i386 (from .../libxrandr2_2%3a1.4.0-1_i386.deb) ... Setting up gcc-4.7-base:i386 (4.7.2-2ubuntu1) ... Setting up libc6:i386 (2.15-0ubuntu20) ... Setting up libgcc1:i386 (1:4.7.2-2ubuntu1) ... Setting up libxau6:i386 (1:1.0.7-1) ... Setting up libxdmcp6:i386 (1:1.1.1-1) ... Setting up libxcb1:i386 (1.8.1-1ubuntu1) ... Setting up libx11-6:i386 (2:1.5.0-1) ... Setting up libxext6:i386 (2:1.3.1-2) ... Setting up libxinerama1:i386 (2:1.1.2-1) ... Setting up libxrender1:i386 (1:0.9.7-1) ... Setting up libxrandr2:i386 (2:1.4.0-1) ... Processing triggers for libc-bin ... ldconfig deferred processing now taking place $ sudo chmod a+rx /opt/openoffice.org3/share/uno_packages/cache/uno_packages chmod: cannot access `/opt/openoffice.org3/share/uno_packages/cache/uno_packages': No such file or directory

  Read the article

• Ubuntu Installation Help for an IBM R31 Thinkpad

  - by David Taylor

  I recently acquired an old IBM R31 Thinkpad, and I'd figure I'd install Lubuntu on it. I've followed the quick steps for USB installation on the help wiki page, but I can't seem to get it to boot from my formatted flash drive. I've checked the boot priority on the BIOS page, but the option to boot from USB doesn't even seem to be there. The only bootable options are legacy and USB floppy drives. The CD drive is shot, so I can't install from there either. Do I have any other options for installation without having to pay for a floppy drive or a replacement CD drive? The wiki pages mentions something about installation from within Windows. Would it be possible to remove Windows using this option, or would it just create a partition? Thanks

  Read the article

• How to use Moonlight to play videos on rtlmost.hu?

  - by B. Roland

  Hi! In Hungary, the biggest TV channel is RTL Klub, they has a video archive site. They use Silverlight instead of Flash :( What is annoying, they use the lastest version of Silverlight, about 4.x. But Moonlight doesn't support it yet. I've been tried in Google Chrome (last dev version), and in Firefox (last stable version), and I've been used the both versions of Moonlight, the lastest stable, and the prerelease. The player loader is displayed, and loaded, but no player displayed after 30 mins waiting. If I want to swith to Ubuntu completly, how can I manage to play these videos? Thanks for your anwsers. Testvideo here. Debug info: Source: http://www.rtlklub.hu/most/player/soda/SodaMediaCenter.Player.Rtl.v3.5.xap Width: 555px Height: 490px Background: # RuntimeVersion: 4.0.50826.0 Windowless: no MaxFrameRate: 60 Codecs: ms-codecs Build configuration: debug, sanity checks

  Read the article

• Kdevelop 4.5.2 on Ubuntu 12.04 ? errors

  - by canatan

  I want to install kdevelop 4.5.2 on Ubuntu 12.04 I ran sudo apt-get install kdevelop 4.5 in the terminal and the installation had a few errors but things looked fine. if i run kdevelop i get the following error Could not find KTextEditor::Factory, check your installation: Make sure that Kate is installed, KDEDIRS is set properly and that you ran kbuildsycoca4. I tried to install kate but I got errors since ubuntu 12.04 does not support kdevelop 4.5.2 officially. Does that mean I'll have to build from source ?

  Read the article

• Lubuntu 13.10 unable to connect to cups localhost:631

  - by user142139

  I am using Lubuntu 13.10 (recently upgraded) and am trying to print to a network printer (HP photosmart 7960) through my router (US Robotics 5461). My printer is connected to the router via USB cable. Normally, I would use the cups configuration interface to set up the wireless connection to the printer. I was able to use the printer through the router wirelessly, using Ubuntu 12.04. Now, with my recently upgraded Lubuntu 13.10, I am unable to get the Cups config webpage (http://localhost:631) to come up. In Chromium, I get: This web page is not available. In Firefox, I get: Unable to connect. Firefox can't establish a connection to the server at localhost:631. The CUPS config file details are below. I have this website to help with the router connections for Linux: http://www.usr.com/support/5461/5461-files/printer_installation_linux/index.html My printer's address through the router is: http://192.168.2.1:1631/printers/My_Printer Can you tell me how to fix this? Or, what to add to the cups configuration file to make this work? Please help. Thanks psychicnut CUPS CONFIG FILE DETAILS: # Show general information in error_log. LogLevel warn MaxLogSize 0 SystemGroup lpadmin Listen /var/run/cups/cups.sock Listen /var/run/cups/cups.sock Listen 192.168.2.1:1631 Browsing Off BrowseLocalProtocols dnssd DefaultAuthType Basic WebInterface Yes <Location /> Order allow,deny </Location> <Location /admin> Order allow,deny </Location> <Location /admin/conf> AuthType Default Require user @SYSTEM Order allow,deny </Location> <Policy default> JobPrivateAccess default JobPrivateValues default SubscriptionPrivateAccess default SubscriptionPrivateValues default <Limit Create-Job Print-Job Print-URI Validate-Job> Order deny,allow </Limit> <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job Cancel-My-Jobs Close-Job CUPS-Move-Job CUPS-Get-Document> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default CUPS-Get-Devices> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After Cancel-Jobs CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit Cancel-Job CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy> <Policy authenticated> JobPrivateAccess default JobPrivateValues default SubscriptionPrivateAccess default SubscriptionPrivateValues default <Limit Create-Job Print-Job Print-URI Validate-Job> AuthType Default Order deny,allow </Limit> <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job Cancel-My-Jobs Close-Job CUPS-Move-Job CUPS-Get-Document> AuthType Default Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After Cancel-Jobs CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> <Limit Cancel-Job CUPS-Authenticate-Job> AuthType Default Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy> JobPrivateAccess default JobPrivateValues default SubscriptionPrivateAccess default SubscriptionPrivateValues default

  Read the article

• Ubuntu 12.04 LTS Wireless Asus USB-N53 (rt3572sta) driver installation issue

  - by Jake Thompson

  My purchase of the Asus USB-N53 just came in today and I spent several hours Googling and researching drivers for this device. When I first plugged the device in it connected fine to my open system, WEP, DHCP configured access point. I opened Google Chrome and a few pages loaded, everything seemed fine. 30 seconds later... Boom! It disconnected and showed attempts to reconnect and asked for the WEP key and just showed a state of infinite connection time until it asked me for the password again. I'm using amd64 (64 bit Ubuntu desktop 12.04 LTS) The official driver can be found here although I had no luck with it. lsusb: Bus 003 Device 002: ID 0b05:179d ASUSTek Computer, Inc. uname -a Linux Jake 3.2.0-31-generic #50-Ubuntu SMP Fri Sep 7 16:16:45 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux ----------------------------------------------------------------------------------Solved: I must of done something wrong when I originally installed the latest drivers from the chipset manufacturers website. I tried reinstalling and did modprobe rt3572sta and waited maybe 10 minutes??? and I connected then I rebooted and everything seems to be working so far. What I did do before hand is unplug the device and typed into the terminal (once for every source I attempted to install): cd '<directory of the driver source>' make uninstall make clean Then I went into the 2.5.0.0 directory and installed that with make make install Then I typed modprobe rt3572sta This was all in superuser. For those who don't know: sudo su

  Read the article

• Unable to ssh out anywhere - ssh_exchange_identification

  - by Chowlett

  I have a setup where I'm running Ubuntu 11.10 as a VirtualBox guest under a Windows 7 host, behind a restrictive corporate firewall. I have set up NAT from the host port 22 to Ubuntu's port 22; IT inform me that they have opened port 22 outbound for the host machine's IP address. I have run ssh-keygen -t rsa, and am trying to test the setup by connecting to github and another known ssh server. In both cases the connect is refused with ssh_exchange_identification: Connection closed by remote host. Full -vvv log is below. Is this possibly still due to the corporate firewall? If so, what else might I need to request from them? Any other ideas what might be wrong and how to fix it? ~$ ssh -Tvvv [email protected] OpenSSH_5.8p1 Debian-7ubuntu1, OpenSSL 1.0.0e 6 Sep 2011 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to github.com [207.97.227.239] port 22. debug1: Connection established. debug3: Incorrect RSA1 identifier debug3: Could not load "/home/chris/.ssh/id_rsa" as a RSA1 public key debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug2: key_type_from_name: unknown key type 'Proc-Type:' debug3: key_read: missing keytype debug2: key_type_from_name: unknown key type 'DEK-Info:' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /home/chris/.ssh/id_rsa type 1 debug1: Checking blacklist file /usr/share/ssh/blacklist.RSA-2048 debug1: Checking blacklist file /etc/ssh/blacklist.RSA-2048 debug1: identity file /home/chris/.ssh/id_rsa-cert type -1 debug1: identity file /home/chris/.ssh/id_dsa type -1 debug1: identity file /home/chris/.ssh/id_dsa-cert type -1 debug1: identity file /home/chris/.ssh/id_ecdsa type -1 debug1: identity file /home/chris/.ssh/id_ecdsa-cert type -1 ssh_exchange_identification: Connection closed by remote host Edit: Requested diagnostics: ~$ ls -la ~/.ssh total 16 drwx------ 2 chris chris 4096 2012-03-30 13:12 . drwxr-xr-x 29 chris chris 4096 2012-03-30 13:25 .. -rw------- 1 chris chris 1766 2012-03-30 13:12 id_rsa -rw-r--r-- 1 chris chris 409 2012-03-30 13:12 id_rsa.pub

  Read the article

• Bluetooth DUN Tethering fails

  - by tacone

  I have an HTC Desire HD, with Android Froyo (2.2) and PDANet installed. I am using Ubuntu 10.10. I cannot tether it over Bluetooth either with Network Manager or BlueMan. (note, I installed Blueman only after failing with NetWork manager, and I even tried the last version from the PPA). With both my device is discovered, paired, setup. But connecting always fail. Network manager says it cannot get the details of my device Blueman says Connection Refused (111) Here are some relevant entries from syslog. Mar 11 22:13:00 tacone-macbook bluetoothd[2242]: Bluetooth deamon 4.69 Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Starting SDP server Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Starting experimental netlink support Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Failed to find Bluetooth netlink family Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Failed to init netlink plugin Mar 11 22:13:00 tacone-macbook kernel: [ 158.284357] Bluetooth: L2CAP ver 2.14 Mar 11 22:13:00 tacone-macbook kernel: [ 158.284361] Bluetooth: L2CAP socket layer initialized Mar 11 22:13:00 tacone-macbook kernel: [ 158.446781] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Mar 11 22:13:00 tacone-macbook kernel: [ 158.446784] Bluetooth: BNEP filters: protocol multicast Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: HCI dev 0 registered Mar 11 22:13:00 tacone-macbook kernel: [ 158.569481] Bluetooth: SCO (Voice Link) ver 0.6 Mar 11 22:13:00 tacone-macbook kernel: [ 158.569484] Bluetooth: SCO socket layer initialized Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: HCI dev 0 up Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Starting security manager 0 Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: ioctl(HCIUNBLOCKADDR): Invalid argument (22) Mar 11 22:13:00 tacone-macbook kernel: [ 158.818600] Bluetooth: RFCOMM TTY layer initialized Mar 11 22:13:00 tacone-macbook kernel: [ 158.818607] Bluetooth: RFCOMM socket layer initialized Mar 11 22:13:00 tacone-macbook kernel: [ 158.818610] Bluetooth: RFCOMM ver 1.11 Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: probe failed with driver input-headset for device /org/bluez/2242/hci0/dev_F8_DB_7F_AF_6B_EE Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: Adapter /org/bluez/2242/hci0 has been enabled Mar 11 22:13:00 tacone-macbook pulseaudio[1757]: bluetooth-util.c: Error from ListDevices reply: org.freedesktop.DBus.Error.AccessDenied Mar 11 22:13:00 tacone-macbook NetworkManager[1247]: <warn> bluez error getting adapter properties: Rejected send message, 1 matched rules; type="method_call", sender=":1.4" (uid=0 pid=1247 comm="NetworkManager) interface="org.bluez.Adapter" member="GetProperties" error name="(unset)" requested_reply=0 destination="org.bluez" (uid=0 pid=2242 comm="/usr/sbin/bluetoothd)) Mar 11 22:13:00 tacone-macbook bluetoothd[2243]: return_link_keys (sba=00:23:6C:B5:03:6F, dba=00:23:6C:C0:F1:B0) Mar 11 22:13:00 tacone-macbook pulseaudio[1757]: bluetooth-util.c: Error from GetProperties reply: org.freedesktop.DBus.Error.AccessDenied Mar 11 22:15:02 tacone-macbook bluetoothd[2243]: Discovery session 0x2262d7c0 with :1.45 activated Mar 11 22:15:15 tacone-macbook bluetoothd[2243]: Stopping discovery Mar 11 22:15:15 tacone-macbook pulseaudio[1757]: bluetooth-util.c: Error from GetProperties reply: org.freedesktop.DBus.Error.AccessDenied Mar 11 22:15:16 tacone-macbook bluetoothd[2243]: link_key_request (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:15:16 tacone-macbook bluetoothd[2243]: io_capa_request (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:15:17 tacone-macbook bluetoothd[2243]: io_capa_response (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:15:18 tacone-macbook bluetoothd[2243]: Stopping discovery Mar 11 22:15:28 tacone-macbook bluetoothd[2243]: link_key_notify (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE, type=5) Mar 11 22:15:28 tacone-macbook kernel: [ 306.585725] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:15:28 tacone-macbook kernel: [ 306.630757] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:15:28 tacone-macbook bluetoothd[2243]: Authentication requested Mar 11 22:15:28 tacone-macbook bluetoothd[2243]: link_key_request (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:15:28 tacone-macbook kernel: [ 306.784829] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:15:28 tacone-macbook kernel: [ 306.857861] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:15:29 tacone-macbook bluetoothd[2243]: probe failed with driver input-headset for device /org/bluez/2242/hci0/dev_F8_DB_7F_AF_6B_EE Mar 11 22:15:29 tacone-macbook pulseaudio[1757]: bluetooth-util.c: Error from GetProperties reply: org.freedesktop.DBus.Error.AccessDenied Mar 11 22:15:29 tacone-macbook pulseaudio[1757]: last message repeated 8 times Mar 11 22:15:29 tacone-macbook bluetoothd[2243]: Stopping discovery Mar 11 22:15:30 tacone-macbook modem-manager: (tty/rfcomm0): could not get port's parent device Mar 11 22:15:30 tacone-macbook modem-manager: (rfcomm0) opening serial device... Mar 11 22:15:30 tacone-macbook modem-manager: (rfcomm0): probe requested by plugin 'Generic' Mar 11 22:15:43 tacone-macbook modem-manager: (rfcomm0) closing serial device... Mar 11 22:15:43 tacone-macbook modem-manager: (rfcomm0) opening serial device... Mar 11 22:15:49 tacone-macbook modem-manager: (rfcomm0) closing serial device... Mar 11 22:16:15 tacone-macbook modem-manager: (tty/rfcomm0): could not get port's parent device Mar 11 22:16:19 tacone-macbook kernel: [ 357.375108] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:16:24 tacone-macbook bluetoothd[2243]: link_key_request (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:16:24 tacone-macbook kernel: [ 362.169506] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:16:24 tacone-macbook kernel: [ 362.215529] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:16:24 tacone-macbook bluetoothd[2243]: link_key_request (sba=00:23:6C:B5:03:6F, dba=F8:DB:7F:AF:6B:EE) Mar 11 22:16:24 tacone-macbook kernel: [ 362.281559] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:16:24 tacone-macbook kernel: [ 362.330588] l2cap_recv_acldata: Unexpected continuation frame (len 0) Mar 11 22:16:24 tacone-macbook modem-manager: (tty/rfcomm0): could not get port's parent device Any help ? PS: tethering via USB or WiFi is not an option, I need to do it over Bluetooth.

  Read the article

• Building Awesome WM

  - by Dragan Chupacabrovic

  Hello, I am following these steps in order to build Awesome window manager on 10.04 I am building 3.4 while the tutorial is for 3.1 I installed all of the specified dependencies including cairo. After running cd awesome-3.4 && make I get the following missing dependencies error: Running cmake… -- cat - /bin/cat -- ln - /bin/ln -- grep - /bin/grep -- git - /usr/bin/git -- hostname - /bin/hostname -- gperf - /usr/bin/gperf -- asciidoc - /usr/bin/asciidoc -- xmlto - /usr/bin/xmlto -- gzip - /bin/gzip -- lua - /usr/bin/lua -- luadoc - /usr/bin/luadoc -- convert - /usr/bin/convert -- checking for modules 'glib-2.0;cairo;x11;pango=1.19.3;pangocairo=1.19.3;xcb-randr;xcb-xtest;xcb-xinerama;xcb-shape;xcb-event=0.3.6;xcb-aux=0.3.0;xcb-atom=0.3.0;xcb-keysyms=0.3.4;xcb-icccm=0.3.6;xcb-image=0.3.0;xcb-property=0.3.0;cairo-xcb;libstartup-notification-1.0=0.10;xproto=7.0.15;imlib2;libxdg-basedir=1.0.0' -- package 'xcb-xtest' not found -- package 'xcb-property=0.3.0' not found -- package 'libstartup-notification-1.0=0.10' not found -- package 'libxdg-basedir=1.0.0' not found CMake Error at /usr/share/cmake-2.8/Modules/FindPkgConfig.cmake:259 (message): A required package was not found Call Stack (most recent call first): /usr/share/cmake-2.8/Modules/FindPkgConfig.cmake:311 (_pkg_check_modules_internal) awesomeConfig.cmake:133 (pkg_check_modules) CMakeLists.txt:15 (include) CMake Error at awesomeConfig.cmake:157 (message): Call Stack (most recent call first): CMakeLists.txt:15 (include) -- Configuring incomplete, errors occurred! make: * [cmake] Error 1 I ran sudo apt-get install libxcb-xtest0 libxcb-property1 libxdg-basedir1 libstartup-notification0 but the problem is still there. It is probably because apt-get uses different names for these libraries. Please advise EDIT following enzotib's suggestion, I ran: sudo apt-get install libxcb-xtest0-dev libxcb-property1-dev libxdg-basedir-dev libstartup-notification0-dev and now it looks like I'm missing a library: awesome-3.4$ make Running cmake… -- cat - /bin/cat -- ln - /bin/ln -- grep - /bin/grep -- git - /usr/bin/git -- hostname - /bin/hostname -- gperf - /usr/bin/gperf -- asciidoc - /usr/bin/asciidoc -- xmlto - /usr/bin/xmlto -- gzip - /bin/gzip -- lua - /usr/bin/lua -- luadoc - /usr/bin/luadoc -- convert - /usr/bin/convert -- Configuring lib/naughty.lua -- Configuring lib/awful/tooltip.lua -- Configuring lib/awful/init.lua -- Configuring lib/awful/titlebar.lua -- Configuring lib/awful/key.lua -- Configuring lib/awful/mouse/init.lua -- Configuring lib/awful/mouse/finder.lua -- Configuring lib/awful/autofocus.lua -- Configuring lib/awful/screen.lua -- Configuring lib/awful/rules.lua -- Configuring lib/awful/widget/init.lua -- Configuring lib/awful/widget/taglist.lua -- Configuring lib/awful/widget/graph.lua -- Configuring lib/awful/widget/tasklist.lua -- Configuring lib/awful/widget/common.lua -- Configuring lib/awful/widget/prompt.lua -- Configuring lib/awful/widget/launcher.lua -- Configuring lib/awful/widget/button.lua -- Configuring lib/awful/widget/layoutbox.lua -- Configuring lib/awful/widget/layout/init.lua -- Configuring lib/awful/widget/layout/vertical.lua -- Configuring lib/awful/widget/layout/horizontal.lua -- Configuring lib/awful/widget/layout/default.lua -- Configuring lib/awful/widget/progressbar.lua -- Configuring lib/awful/widget/textclock.lua -- Configuring lib/awful/dbus.lua -- Configuring lib/awful/remote.lua -- Configuring lib/awful/client.lua -- Configuring lib/awful/prompt.lua -- Configuring lib/awful/completion.lua -- Configuring lib/awful/tag.lua -- Configuring lib/awful/util.lua -- Configuring lib/awful/button.lua -- Configuring lib/awful/menu.lua -- Configuring lib/awful/hooks.lua -- Configuring lib/awful/wibox.lua -- Configuring lib/awful/layout/init.lua -- Configuring lib/awful/layout/suit/init.lua -- Configuring lib/awful/layout/suit/floating.lua -- Configuring lib/awful/layout/suit/fair.lua -- Configuring lib/awful/layout/suit/spiral.lua -- Configuring lib/awful/layout/suit/magnifier.lua -- Configuring lib/awful/layout/suit/tile.lua -- Configuring lib/awful/layout/suit/max.lua -- Configuring lib/awful/placement.lua -- Configuring lib/awful/startup_notification.lua -- Configuring lib/beautiful.lua -- Configuring themes/zenburn//theme.lua -- Configuring themes/default//theme.lua -- Configuring themes/sky//theme.lua -- Configuring config.h -- Configuring awesomerc.lua -- Configuring awesome-version-internal.h -- Configuring awesome.doxygen -- Configuring done -- Generating done -- Build files have been written to: /home/druden/util/awesome-3.4/.build-vedroid-i486-linux-gnu-4.4.3 Running make Makefile… Building… [ 4%] Built target generated_sources [ 5%] Building C object CMakeFiles/awesome.dir/awesome.c.o In file included from /home/druden/util/awesome-3.4/spawn.h:25, from /home/druden/util/awesome-3.4/awesome.c:33: /home/druden/util/awesome-3.4/globalconf.h:57: error: expected specifier-qualifier-list before ‘xcb_event_handlers_t’ In file included from /home/druden/util/awesome-3.4/awesome.c:34: /home/druden/util/awesome-3.4/client.h: In function ‘client_stack’: /home/druden/util/awesome-3.4/client.h:212: error: ‘awesome_t’ has no member named ‘client_need_stack_refresh’ /home/druden/util/awesome-3.4/client.h: In function ‘client_raise’: /home/druden/util/awesome-3.4/client.h:227: error: ‘awesome_t’ has no member named ‘stack’ In file included from /home/druden/util/awesome-3.4/awesome.c:42: /home/druden/util/awesome-3.4/titlebar.h: In function ‘titlebar_update_geometry’: /home/druden/util/awesome-3.4/titlebar.h:150: error: ‘awesome_t’ has no member named ‘L’ /home/druden/util/awesome-3.4/titlebar.h:151: error: ‘awesome_t’ has no member named ‘L’ /home/druden/util/awesome-3.4/titlebar.h:152: error: ‘awesome_t’ has no member named ‘L’ In file included from /home/druden/util/awesome-3.4/awesome.c:47: /home/druden/util/awesome-3.4/common/xutil.h: In function ‘xutil_get_text_property_from_reply’: /home/druden/util/awesome-3.4/common/xutil.h:39: warning: ‘STRING’ is deprecated (declared at /usr/local/include/xcb/xcb_atom.h:83) /home/druden/util/awesome-3.4/common/xutil.h: At top level: /home/druden/util/awesome-3.4/common/xutil.h:60: error: expected ‘)’ before ‘*’ token /home/druden/util/awesome-3.4/awesome.c: In function ‘awesome_atexit’: /home/druden/util/awesome-3.4/awesome.c:65: error: ‘awesome_t’ has no member named ‘hooks’ /home/druden/util/awesome-3.4/awesome.c:66: error: ‘awesome_t’ has no member named ‘L’ /home/druden/util/awesome-3.4/awesome.c:66: error: ‘awesome_t’ has no member named ‘hooks’ /home/druden/util/awesome-3.4/awesome.c:68: error: ‘awesome_t’ has no member named ‘L’ /home/druden/util/awesome-3.4/awesome.c:73: error: ‘awesome_t’ has no member named ‘embedded’ /home/druden/util/awesome-3.4/awesome.c:76: error: ‘awesome_t’ has no member named ‘embedded’ /home/druden/util/awesome-3.4/awesome.c:77: error: ‘awesome_t’ has no member named ‘embedded’ /home/druden/util/awesome-3.4/awesome.c:89: error: ‘awesome_t’ has no member named ‘clients’ /home/druden/util/awesome-3.4/awesome.c:89: error: ‘awesome_t’ has no member named ‘clients’ /home/druden/util/awesome-3.4/awesome.c:89: error: ‘awesome_t’ has no member named ‘clients’ /home/druden/util/awesome-3.4/awesome.c:89: warning: type defaults to ‘int’ in declaration of ‘c’ /home/druden/util/awesome-3.4/awesome.c:89: error: ‘awesome_t’ has no member named ‘clients’ /home/druden/util/awesome-3.4/awesome.c:89: error: ‘awesome_t’ has no member named ‘clients’ /home/druden/util/awesome-3.4/awesome.c:89: error: ‘awesome_t’ has no member named ‘clients’ /home/druden/util/awesome-3.4/awesome.c:91: error: invalid type argument of ‘unary *’ (have ‘int’) /home/druden/util/awesome-3.4/awesome.c:92: error: invalid type argument of ‘unary *’ (have ‘int’) /home/druden/util/awesome-3.4/awesome.c:96: error: ‘awesome_t’ has no member named ‘L’ /home/druden/util/awesome-3.4/awesome.c: In function ‘a_xcb_check_cb’: /home/druden/util/awesome-3.4/awesome.c:223: warning: implicit declaration of function ‘xcb_event_handle’ /home/druden/util/awesome-3.4/awesome.c:223: error: ‘awesome_t’ has no member named ‘evenths’ /home/druden/util/awesome-3.4/awesome.c:230: error: ‘awesome_t’ has no member named ‘evenths’ /home/druden/util/awesome-3.4/awesome.c: In function ‘awesome_restart’: /home/druden/util/awesome-3.4/awesome.c:277: error: ‘awesome_t’ has no member named ‘argv’ /home/druden/util/awesome-3.4/awesome.c: In function ‘xerror’: /home/druden/util/awesome-3.4/awesome.c:305: error: ‘XCB_EVENT_ERROR_BAD_WINDOW’ undeclared (first use in this function) /home/druden/util/awesome-3.4/awesome.c:305: error: (Each undeclared identifier is reported only once /home/druden/util/awesome-3.4/awesome.c:305: error: for each function it appears in.) /home/druden/util/awesome-3.4/awesome.c:306: error: ‘XCB_EVENT_ERROR_BAD_MATCH’ undeclared (first use in this function) /home/druden/util/awesome-3.4/awesome.c:308: error: ‘XCB_EVENT_ERROR_BAD_VALUE’ undeclared (first use in this function) /home/druden/util/awesome-3.4/awesome.c: In function ‘main’: /home/druden/util/awesome-3.4/awesome.c:369: error: ‘awesome_t’ has no member named ‘keygrabber’ /home/druden/util/awesome-3.4/awesome.c:370: error: ‘awesome_t’ has no member named ‘mousegrabber’ /home/druden/util/awesome-3.4/awesome.c:376: error: ‘awesome_t’ has no member named ‘argv’ /home/druden/util/awesome-3.4/awesome.c:377: error: ‘awesome_t’ has no member named ‘argv’ /home/druden/util/awesome-3.4/awesome.c:381: error: ‘awesome_t’ has no member named ‘argv’ /home/druden/util/awesome-3.4/awesome.c:382: error: ‘awesome_t’ has no member named ‘argv’ /home/druden/util/awesome-3.4/awesome.c:424: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:425: error: ‘awesome_t’ has no member named ‘timer’ /home/druden/util/awesome-3.4/awesome.c:425: error: ‘awesome_t’ has no member named ‘timer’ /home/druden/util/awesome-3.4/awesome.c:425: error: ‘awesome_t’ has no member named ‘timer’ /home/druden/util/awesome-3.4/awesome.c:425: error: ‘awesome_t’ has no member named ‘timer’ /home/druden/util/awesome-3.4/awesome.c:425: error: ‘awesome_t’ has no member named ‘timer’ /home/druden/util/awesome-3.4/awesome.c:425: error: ‘awesome_t’ has no member named ‘timer’ /home/druden/util/awesome-3.4/awesome.c:431: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:432: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:433: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:434: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:435: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:436: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:443: error: ‘awesome_t’ has no member named ‘default_screen’ /home/druden/util/awesome-3.4/awesome.c:450: error: ‘awesome_t’ has no member named ‘have_xtest’ /home/druden/util/awesome-3.4/awesome.c:462: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:464: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:465: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:467: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:468: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:471: warning: implicit declaration of function ‘xcb_event_handlers_init’ /home/druden/util/awesome-3.4/awesome.c:471: error: ‘awesome_t’ has no member named ‘evenths’ /home/druden/util/awesome-3.4/awesome.c:472: warning: implicit declaration of function ‘xutil_error_handler_catch_all_set’ /home/druden/util/awesome-3.4/awesome.c:472: error: ‘awesome_t’ has no member named ‘evenths’ /home/druden/util/awesome-3.4/awesome.c:490: warning: implicit declaration of function ‘xcb_event_poll_for_event_loop’ /home/druden/util/awesome-3.4/awesome.c:490: error: ‘awesome_t’ has no member named ‘evenths’ /home/druden/util/awesome-3.4/awesome.c:493: error: ‘awesome_t’ has no member named ‘evenths’ /home/druden/util/awesome-3.4/awesome.c:496: error: ‘awesome_t’ has no member named ‘keysyms’ /home/druden/util/awesome-3.4/awesome.c:507: error: ‘awesome_t’ has no member named ‘colors’ /home/druden/util/awesome-3.4/awesome.c:510: error: ‘awesome_t’ has no member named ‘colors’ /home/druden/util/awesome-3.4/awesome.c:513: error: ‘awesome_t’ has no member named ‘font’ /home/druden/util/awesome-3.4/awesome.c:519: error: ‘awesome_t’ has no member named ‘keysyms’ /home/druden/util/awesome-3.4/awesome.c:519: error: ‘awesome_t’ has no member named ‘numlockmask’ /home/druden/util/awesome-3.4/awesome.c:520: error: ‘awesome_t’ has no member named ‘shiftlockmask’ /home/druden/util/awesome-3.4/awesome.c:520: error: ‘awesome_t’ has no member named ‘capslockmask’ /home/druden/util/awesome-3.4/awesome.c:521: error: ‘awesome_t’ has no member named ‘modeswitchmask’ /home/druden/util/awesome-3.4/awesome.c:563: error: ‘awesome_t’ has no member named ‘evenths’ /home/druden/util/awesome-3.4/awesome.c:572: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:575: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:576: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:577: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:578: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:579: error: ‘awesome_t’ has no member named ‘loop’ /home/druden/util/awesome-3.4/awesome.c:580: error: ‘awesome_t’ has no member named ‘loop’ make[3]: * [CMakeFiles/awesome.dir/awesome.c.o] Error 1 make[2]: [CMakeFiles/awesome.dir/all] Error 2 make[1]: [all] Error 2 make: * [cmake-build] Error 2

  Read the article

< Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >