Search Results

Search found 3938 results on 158 pages for 'goal'.

Page 99/158 | < Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >

  • SSD cache to minimize HDD spin-up time?

    - by sirprize
    short version first: I'm looking for Linux compatible software which is able to transparently cache HDD writes using an SSD. However, I only want to spin up the HDD once or twice a day (to write the cached data to the HDD). The rest of the time, the HDD should not be spinning due to noise concerns. Now the longer version: I have built a completely silent computer running Xubuntu. It has a A10-6700T APU, huge fanless cooler, fanless PSU, SSD. The problem is: it also has (and needs) a noisy HDD and I want to forbid spinning it up during the night. All writes should be cached on the SSD, reads are not needed in the night. Throughout every day, this computer will automatically download about 5 GB of data which will be retained for about a year, giving a total needed disk capacity of slightly less than 2 TB. This data is currently stored on a 3 TB noisy hard disk drive which is spinning day and night. Sometimes, I'll need to access some data from several months ago. However, most times I'll only need data from the last 14 days, which would fit on the SSD. Ideally, I'd like a transparent solution (all data on one filesystem) which caches all writes to the SSD, writing to the HDD only once a day. Reads would be served by the cache if they were still on the SDD, else the HDD would have to spin up. I have tried bcache without much success (using cache_mode=writeback, writeback_running=0, writeback_delay=86400, sequential_cutoff=0, congested_write_threshold_us=0 - anything missing?) and I read about ZFS ZIL/L2ARC but I'm not sure I can achieve my goal with ZFS. Any pointers? If all else fails, I will simply use some scripts to automatically copy files over to the big drive while deleting the oldest files from the SSD.

    Read the article

  • IPSec for LAN traffic: Basic considerations?

    - by chris_l
    This is a follow-up to my Encrypting absolutely everything... question. Important: This is not about the more usual IPSec setup, where you want to encrypt traffic between two LANs. My basic goal is to encrypt all traffic within a small company's LAN. One solution could be IPSec. I have just started to learn about IPSec, and before I decide on using it and dive in more deeply, I'd like to get an overview of how this could look like. Is there good cross-platform support? It must work on Linux, MacOS X and Windows clients, Linux servers, and it shouldn't require expensive network hardware. Can I enable IPSec for an entire machine (so there can be no other traffic incoming/outgoing), or for a network interface, or is it determined by firewall settings for individual ports/...? Can I easily ban non-IPSec IP packets? And also "Mallory's evil" IPSec traffic that is signed by some key, but not ours? My ideal conception is to make it impossible to have any such IP traffic on the LAN. For LAN-internal traffic: I would choose "ESP with authentication (no AH)", AES-256, in "Transport mode". Is this a reasonable decision? For LAN-Internet traffic: How would it work with the internet gateway? Would I use "Tunnel mode" to create an IPSec tunnel from each machine to the gateway? Or could I also use "Transport mode" to the gateway? The reason I ask is, that the gateway would have to be able to decrypt packages coming from the LAN, so it will need the keys to do that. Is that possible, if the destination address isn't the gateway's address? Or would I have to use a proxy in this case? Is there anything else I should consider? I really just need a quick overview of these things, not very detailed instructions.

    Read the article

  • Migrating 10-15 Websites Running Linux, LAMP, RoR, WordPress

    - by Michael
    Task is to move 10-15 websites running Linux to new servers hosted by Amazon. These boxes are currently on dedicated servers. Some sites are running WordPress, some have custom CMS, and others might have RoR applications. Unfortunately, there is sparse documentation regarding each site and how services/files are dependent on each other which means there is a lot of detective work that needs to take place. My goal is to properly document each site, what makes them work, etc., so future admins have at least something to work with. Currently my strategy is to download each site so I have a backup of the files then scan through them looking for configuration files -- db connections, apache configs, etc. Then, create a nice spreadsheet with these findings and migrate these out to the new server. My question to ServerFault is this, are there things you would look out for? Easier ways to handle this task that I'm missing? Points will be awarded to answers that help with efficiency. Thanks in advance.

    Read the article

  • What do you upgrade to make games load faster? [on hold]

    - by Superbest
    Let's say you have a relatively modern game like Shogun 2. The loading screens take several minutes. This bothers you and you'd like to improve it. What is actually going on when loading screens are up? I'm guessing assets are being loaded into memory from disk, and possibly being decompressed first. However, what is actually causing the slow down? The memory? Mainboard? CPU? HDD? If you had $100 to spend on upgrades and your only goal is to speed up loading screens without reducing other performance, what component of the computer does it make sense to upgrade for maximum benefit? If your answer is "it depends on the existing setup", what sort of benchmarks would you run to determine what is causing the bottleneck? What if you had $500 instead? I give the two budgets for context. I am not asking for actual recommendations about which component to buy (nor are the numbers supposed to be rigid limits), but what features are important when shopping for components with small and large budgets (a large budget could allow buying multiple components which are not so good on their own, but work particularly well together). I mention Shogun 2 as an example, but I'm asking about reducing overall loading times, across all games, not just one game. Therefore, "put it on a solid state disk" probably won't be good solution, because putting every game on your SDD will quickly fill it up.

    Read the article

  • Performance Test and TCP tuning

    - by Mithir
    We are in the process of performance testing an application which receives tcp requests converts them to soap requests (WCF-httpBinding) which other services work on. The server is Windows Server 2008 R2. The TCP requests are received by TcpListener instance (.NET C#). There are 3 http-binded WCF services running on the same server. We have built a performance test client which goal is to simulate multiple concurrent requests(each request has to be different and recognizable by the application). We built a test running 150 requests that run on the same time (by 150 different threads), and we noticed straight away that some requests get the TCP connection slowly, but once they get it, they act fast. A single request writes twice on the same connection- request and an application ack. Although a single request+ack can take about 150ms, the 150 test takes about 7 seconds. The Problem When we try to run this test from 2 different computers we lose requests. some clients requests are getting no connection was made because the target machine actively refused it So I got here and got convinced it was because of the backlog. I changed the TcpListener parameters and did the registry AFD backlog changes written here but it still didn't work, so I inserted all of the TCP tuning suggested plus some netsh commands which were recommended, but still no change, we still get that error. Is there anything else I need to know? Are there any other solutions?

    Read the article

  • mount nfs subdirectory and still apply parent directory permissions

    - by Christophe Drevet
    A NFS server exports : /export/home computers /export/cont1 computers On the filesystem, there are these permissions : $ ls -al /export/cont1 drwxr-x--- 6 root group1 4096 2010-05-04 10:57 . drwxrwxrwx 5 root root 4096 2010-05-07 14:52 .. drwxrwxrwx 2 root root 4096 2010-05-06 20:33 .snapshot drwxr-xr-x 2 user1 group1 4096 2010-05-04 10:57 user1 drwxr-xr-x 2 user2 group1 4096 2010-05-04 10:57 user2 drwxr-xr-x 2 user3 group1 4096 2010-05-04 10:57 user3 So that user4, which is in not in the group1 can't access this directory and its subdirectories. Now, on its client machine, this user can do : $ sudo mount server:/export/cont1/user3 /mnt/temp and then access the directory without permissions on /export/cont1 : $ id uid=7943(user4) gid=7943(user4) groupes=1189(group4) $ ls -al /mnt/temp/ drwxr-xr-x 3 user3 group1 4096 2010-05-04 10:57 . drwxr-xr-x 7 root root 4096 2010-05-04 11:02 .. -rw-r--r-- 1 user3 group1 6 2010-05-04 10:56 README Is there a way to apply /export/cont1 permissions even if it is not mounted ? The goal is to enable users to mount /home/user3 and only access it if they can access /export/cont1 on the nfs server. Said in another way : how can I allow a machine to mount /export/cont1/user3 and still don't allow user4 to access it. Maybe NFSv4 and Kerberos can help ?

    Read the article

  • The bottlenecks of any computer, what to look for?

    - by WebDevHobo
    Whether it is a laptop or a desktop, any computer is made up of several pieces of hardware that communicate with each other. Sending data back and forth to ensure that the user gets the desired results. I have seen some theoretical stuff on computers & hardware, but I wonder how it all comes together. CPU RAM Graphics Card L1 CACHE L2 CACHE L3 CACHE FSB ... And all other things. Which is the biggest bottle neck? Why would a person not want/need a big value in one of those categories in certain situations? P.S.: when reading the specs of the i5 750 processor, I came across this description: In place of the FSB, one or more high speed, point-to-point buses called Quick Path Interconnect (QPI) are used, formerly known as Common Serial Interconnect Bus or CSI. QPI features higher bandwidth than the traditional FSB and is better suited to system scaling. What is this, and how does it compare to FSB? EDIT: I am not planning to buy a computer at all. The goal of this question is to understand the internal relation of various hardware pieces, their specific functions and how they work together. For instance, I have heard to a somewhat higher-than-usual amount of L2/L3 Cache can help speed up your computer. What's up with saying that? Also I forgot to mention Hard-disk RPM.

    Read the article

  • Apache: rewrite port 80 and 443 - multiple SSL vhosts setup

    - by Benjamin Jung
    SETUP: multiple SSL domains are configured on a single IP, by using vhosts with different port numbers (on which Apache listens) Apache 2.2.8 on Windows 2003 (no comments on this pls) too many Windows XP users so SNI isn't an option yet There may be reasons why it's wrong to use this approach, but it works for now. vhosts setup: # secure domain 1 <VirtualHost IP:443> SSL stuff specifying certificate etc. ServerName domain1.org </VirtualHost> # secure domain 2 <VirtualHost IP:81> SSL stuff for domain2.org ServerName domain2.org </VirtualHost> GOAL: Some folders inside the domain2.org docroot need to be secure. I used a .htaccess file to rewrite the URL to https on port 81: RewriteEngine On RewriteCond %{SERVER_PORT} !^81$ RewriteRule (.*) https://%{HTTP_HOST}:81%{REQUEST_URI} [R] Suppose I put the .htaccess in the folder 'secfolder'. When accessing http://domain2.org/secfolder this gets succesfully rewritten to https://domain2.org:81/secfolder. ISSUE: When accessing https://domain2.org/secfolder (without port 81), the certificate from the first vhost (domain1.org) is used and the browser complains that the site is insecure because the certificate is not valid for domain2.org. I thought that RewriteCond %{SERVER_PORT} !^81$ would also rewrite https://domain2.org to https://domain2.org:81, but it doesn't. It seems that the .htaccess file is not being used at all in this case. At this point I am not sure how to apply a RewriteRule to https://domain2.org. I tried creating an additional vhost for domain2 on port 443 before the one for domain1.org, but Apache seems to choke on that. I hope someone of you has an idea how to approach this. TIA.

    Read the article

  • Best way to convert episodic DVDs for Windows Media Center?

    - by Roger Lipscombe
    I'm archiving my DVD collection. My goal is to be able to play them back in Windows Media Center. For feature-length DVDs, I'm using AnyDVD and CloneDVD, which is working well. For playing back TV shows (and other episodic content), I'm using Media Browser, which doesn't support a VIDEO_TS folder per episode. It expects the shows to be broken up into one file per episode (e.g. "Willo the Wisp - S01E12.avi"). For this, I'm attempting to use Handbrake, which, for extracting the episodes from DVD (or already-ripped VIDEO_TS folder), is working pretty well. The problem that I have is that the default x264 encoder over-compresses the resulting video stream, which results in hideous artifacts in animated shows. The aforementioned Willo the Wisp is a particularly bad example, because the original DVD is particularly "noisy". If I switch to using the ffmpeg encoder, the artifacts are gone in Windows Media Player, but I can't get the resulting files to play back in Windows Media Center. I see the first frame, and then there's an error message. I've installed the CCCP codec collection, but it doesn't seem to have made any difference. So: what's the best way to convert VIDEO_TS to individual episode files for playback in Windows Media Center?

    Read the article

  • Desktop virtualization

    - by gurpal2000
    Is there currently a proper Type 1 "desktop" hypervisor? Either free or not? This is just for tinkering around at home on some beefy Phenom machines. Basically i want to be able to run say 2 OSs on the same PC but without loading windows or a heavy flavour of linux and then use a hotkey to switch between them. I should get full performance out of them. So do i need something better than vmware workstation and/or virtualbox. I think these are "Type 2"? I already run VMWare w/s and VBox but is there a more performant solution? I saw a YouTube video from Citrix where a laptop was running XP and Vista. With the touch of a hot key they could switch between them. There was no visible underlying OS (there might be a hypervisor)? I have access to Citrix XenDesktop 3 enterprise edition evaluation. I realise this isn't for desktops but can i achieve my goal (geekiness) ? If i use the free XenServer 5.5.0 how do my client PCs access windows/linux/whatever from the xenserver? Is it via a thin client RDP type application? If so if there one for both windows and linux? Also if i do use XenServer can i use USB in either direction? What is Citrix receiver can i use that for (3) ? If so, is there some hotkey i can configure? whatever client is used to access the server software (whether it be on a different server or local) can i get full opengl/directx acceleration? what about Xen? i tried the Xen LiveCD but no clue as how to configure it. As you can see much confusion. Any help/pointers welcome. Cheers.

    Read the article

  • Can I get ethernet out of my Verizon FIOS set-top box?

    - by Tom Hughes
    Setup: my home network is long & skinny, and the FIOS-connected router is all the way at one of the apartment. At the other end, far away (and a floor higher) is my HD TV, which gets a cable-TV signal from a Verizon set-top box that is coax-connected back to the FIOS on-premises equipment. Wi-Fi won't work, the apartment is too stretched out, with old, thick walls and floors. Goal: I think there are three ways to get ethernet back to where the HD TV is: 1) run a cable! this isn't crazy but isn't cheap either (my building won't let me do it, it involves hiring an electrician because the cable would run partly through the public hallway ceiling) 2) split the coax near the TV and put in... a MoCA device? 3) somehow tease the set-top box, which has an RJ-11 (ethernet) port on the back, to give me network access. Question: any other choices? and, is one choice better than the others? #3 is by far the most desirable because it would involve the least wiring -- but I can't find any resources to help make it happen. #2 is a bit scary, I don't want to degrade service to the TV or anywhere else for that matter.

    Read the article

  • Architecture for highly available MySQL with automatic failover in physically diverse locations

    - by Warner
    I have been researching high availability (HA) solutions for MySQL between data centers. For servers located in the same physical environment, I have preferred dual master with heartbeat (floating VIP) using an active passive approach. The heartbeat is over both a serial connection as well as an ethernet connection. Ultimately, my goal is to maintain this same level of availability but between data centers. I want to dynamically failover between both data centers without manual intervention and still maintain data integrity. There would be BGP on top. Web clusters in both locations, which would have the potential to route to the databases between both sides. If the Internet connection went down on site 1, clients would route through site 2, to the Web cluster, and then to the database in site 1 if the link between both sites is still up. With this scenario, due to the lack of physical link (serial) there is a more likely chance of split brain. If the WAN went down between both sites, the VIP would end up on both sites, where a variety of unpleasant scenarios could introduce desync. Another potential issue I see is difficulty scaling this infrastructure to a third data center in the future. The network layer is not a focus. The architecture is flexible at this stage. Again, my focus is a solution for maintaining data integrity as well as automatic failover with the MySQL databases. I would likely design the rest around this. Can you recommend a proven solution for MySQL HA between two physically diverse sites? Thank you for taking the time to read this. I look forward to reading your recommendations.

    Read the article

  • Using radvd to advertise ipv6 over VPN connection using DD-wrt

    - by Sean Madden
    My ultimate goal is to allow VPN users to have access to my internal IPv6 network from across the intertubes. I've got a linksys WRT54GSv2 running DD-WRTv24SP1 and have configured the little guy as specified here http://www.dd-wrt.com/wiki/index.php/IPv6 and it works wonderfully over the br0 interface (LAN/WLAN bridge). Here's the issue though, when I add an additional interface to the radvd config file on the router (specifically ppp0, for the VPN traffic), radvd refuses to start. The kicker is that on DDWRT, it doesn't give an error message, it just fails outright. Any suggestions on where to proceed from here? /jffs/radvd.conf: interface br0 { AdvSendAdvert on; prefix 0:0:0:1::/64 { AdvOnLink on; AdvAutonomous on; }; }; interface ppp0 { AdvSendAdvert on; prefix 0:0:0:1::/64 { AdvOnLink on; AdvAutonomous on; }; }; The documentation I've found for radvd is slim, but if anyone has a decent idea on how to proceed I'd love to hear it.

    Read the article

  • Force local IP traffic to an external interface

    - by calandoa
    I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to forward all the traffic sent to one of these local addresses through the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 should be not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. May be I could then do NAT forwarding of all traffic directed to fake 192.168.1.2 on eth1, rerouted to 192.168.1.1 internally? I am actually struggling with iptables, but it is too tough for me. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

    Read the article

  • Does the Lenovo t60p vga port support an s-video signal?

    - by Matthijs Wessels
    I just bought a new television. The problem is it turns out it doesn't have a VGA port. It does have: s-video, component, hdmi and scart. My Lenovo t60p only has vga. If have search frantically for a solution and even though it seems I have sooo many options they are all dead ends. Or I keep ending up having to buy a 100 euro box to convert the signal. However, I found that some video cards support s-video through the vga port. It says look it up in your video cards documentation. I have a Lenovo t60p laptop with a ATI MOBILITY FireGl v5250. But I can't seem to get my hands on any documentation where this is supposed to be documented. I found this website: http://forum.notebookreview.com/showthread.php?t=179529&highlight=s-video There this guy says he thinks it's in the t60 but dropped in the t61, but suggests to the guy with the t60 that it won't work. I can't really conclude anything from that. Furthermore, I am not looking for the best of the best quality. So when I found this: *http://www.amazon.com/VideoSecu-Computor-Presentation-Converter-VGA2TV/dp/B000X3FAJU/ref=pd_cp_e_3_img I woudl be quite happy with this. Except that I don't think I can order it because I don't live in the US. Can anybody give me a definite answer, to whether the vga port of my lenovo t60p ati firegl v5250 supports s-video? So that I can just by a vga to s-video cable to achieve my goal.

    Read the article

  • HAProxy "503 Service Unavailable" for webserver running on a KVM virtual machine

    - by Menda
    I'm setting up a server with KVM (IP 192.168.0.100) and I have created inside of it one virtual machine using network bridging at 192.168.0.194. This virtual machine has an nginx instance running, which I can access from the server or from any computer computer in the internal network just typing in the browser http://192.168.0.194. However, I try configure HAProxy in the same server that hosts KVM and looking the status page of HAProxy it always shows the virtual machine as "DOWN". If I try from the server http://localhost, it should be the same than if I go to http://192.168.0.194. My goal is to build a reverse proxy, but I tried this little example and won't work. What am I doing bad? This is my config file in the server: # /etc/haproxy/haproxy.cfg global maxconn 4096 user haproxy group haproxy daemon defaults log global mode http option httplog option dontlognull retries 3 option redispatch maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 listen ServerStatus *:8081 mode http stats enable stats auth haproxy:haproxy listen Server *:80 mode http balance roundrobin cookie JSESSIONID prefix option httpclose option forwardfor option httpchk HEAD /check.txt HTTP/1.0 server mv1 192.168.0.194:80 cookie A check Thanks.

    Read the article

  • Custom MS-DOS / FreeDOS

    - by user1801387
    Goal : Build a custom DOS to boot into. To automate tasks like formating a drive, or doing recovery. I've been using Grub4DOS to boot into these images. So far I've looking into taking a windows repair disk ISO and extracting. I can't seem to find the autoexec.bat in the disk. I really don't know where to look for the startup configuration file to change or how to add an autoexec.bat. I've tried MS-DOS 6.22. But it lacks the diskpart tool I require. I've tried extracting the images and adding it. Then I got a boot failed. I assume that after i added it. All the files when to lower case names and I assume that the OS is case sensitive. Then I've looking into using FreeDOS. But I don't know how it works at all. Partially because I can't seem to grasp the help/wiki's information. I looked into getting a bearbones release with just the kernel and I think it's the config.sys file. But I don't have any idea on how the packaging system works to incorporate diskpart into it. So really I'm in general looking for a small bootable DOS to where I can incorporate diskpart and setup an autoexec.bat for the actual function to carry out and to boot into. Thanks :) This is just for personal use also.

    Read the article

  • Apache virtualhost - only apply script if file does not exist in document root

    - by Brett Thomas
    Sorry for the newbie apache question. I'm wondering if it's possible to set up the following non-conventional apache virtualhost (for a Django app): -- If a file exists in the DocumentRoot (/var/www) it will be shown. So if /var/www/foo.html exists, then it can be seen at www.example.com/foo.html. -- If file does not exist, it is served via a virtualhost. I'm using mod_wsgi with a WSGIScriptAlias directive that points to a Django app. So if there is no /var/www/bar.html, www.example.com/bar.html will be passed to the Django app, which may or may not be a 404 error. One option is to create an Alias for each individual file/directory, but people want to be able to post a file without adding an alias, and we want to keep the above URL structure for legacy reasons. Simplified Virtualhost is: <VirtualHost *:80> ServerName www.example.com DocumentRoot /var/www WSGIScriptAlias / /path/to/django.wsgi <Directory /path/to/app> Order allow,deny Allow from all </Directory> Alias /hi.html /var/www/hi.html </VirtualHost> The goal is to have www.example.com/hi.html work as above, without the Alias line

    Read the article

  • network policy + WPA enterprise (tkip) Windows 2008 R2

    - by Aceth
    hi I've attempted the following guide and in a bit of a pickle. http://techblog.mirabito.net.au/?p=87 My main goal is to have a username / password based wireless authentication with active directory integration. I keep getting the error Network Policy Server denied access to a user. Contact the Network Policy Server administrator for more information. User: Security ID: domain\rhysbeta Account Name: rhysbeta Account Domain: domain Fully Qualified Account Name: domain\rhysbeta Client Machine: Security ID: NULL SID Account Name: - Fully Qualified Account Name: - OS-Version: - Called Station Identifier: 00-12-BF-00-71-3C:wirelessname Calling Station Identifier: 00-23-76-5D-1E-31 NAS: NAS IPv4 Address: 0.0.0.0 NAS IPv6 Address: - NAS Identifier: - NAS Port-Type: Wireless - IEEE 802.11 NAS Port: 2 RADIUS Client: Client Friendly Name: Belkin54g Client IP Address: x.x.x.10 Authentication Details: Connection Request Policy Name: Secure Wireless Connections Network Policy Name: Secure Wireless Connections Authentication Provider: Windows Authentication Server: srvr.example.com Authentication Type: EAP EAP Type: - Account Session Identifier: - Logging Results: Accounting information was written to the local log file. Reason Code: 22 Reason: The client could not be authenticated because the Extensible Authentication Protocol (EAP) Type cannot be processed by the server. ` I would love to have it so that non domain devices

    Read the article

  • windows 7: Event 55 The file system structure on the disk is corrupt and unusable

    - by Radio
    Here is a real bad one! Windows 7 RTM with SP1 installed [Version 6.1.7601]. Recently tried to delete some folder on my hard drive and Windows prompted "Error 0x80070570: The file or directory is corrupted and unreadable", and at the same time placed an Event 55 describing "The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on \Device\HarddiskVolume2." Ran chkdsk, first with /f option, then with /r option. Result in both cases was: no errors found, 0 bad sectors. No problems chkdsk found at all! Went through StackExchange, Google and spent over 6 hours on this. Still cannot figure out the problem. Re-installing/Re-Formatting is not an option! What did I try: Hotfix - Windows6.1-KB982927-x64.msu - gave me an error about incompatibility with my computer, however it totally matches my system. CRC of hotfix was ok. Windows Repair Console found startup errors and fixed those, but this didn't help an issue, even by running chkdsk c: /R from it. http://support.microsoft.com/kb/246026 does not promise anything good. sfc /scannow does not help too. Replaced hard drive by cloning an old one using True Image, repeated all steps above. At the same time, some minor glitches started to appear in my Windows, like side panel and notification area settings are getting reset. Goal is to delete the folder and get rid of Event 55. Sounds like NTFS bug. Please help. This is completely ridiculous.

    Read the article

  • Two DHCP servers on the same network

    - by CesarGon
    We are setting up a routing link between the Windows Server 2008 networks of two different buildings in my organisation. Each network uses a different IP addressing scheme (one uses public addresses, the other one uses private), but the goal is having a single Windows Server domain across the gap between the buildings. The link is provided by a 100-Mbps point-to-point line. I have always understood that you should not have more than one DHCP server on a network. However, we are planning to put a domain controller on each building, and each domain controller will be a DNS server and a DHCP server as well. The intention is that a machine booting up in building A gets its IP address from the DHCP server closer to it, in building A, while a machine booting up in building B gets an address from the DHCP server in building B. Since the two buildings will be linked and the network will be only one, will this work? How can I avoid that a machine booting up in building A gets an address from the DHCP server in building B (or vice versa)? Thanks.

    Read the article

  • Two DHCP servers on the same network

    - by CesarGon
    We are setting up a routing link between the Windows Server 2008 networks of two different buildings in my organisation. Each network uses a different IP addressing scheme (one uses public addresses, the other one uses private), but the goal is having a single Windows Server domain across the gap between the buildings. The link is provided by a 100-Mbps point-to-point line. I have always understood that you should not have more than one DHCP server on a network. However, we are planning to put a domain controller on each building, and each domain controller will be a DNS server and a DHCP server as well. The intention is that a machine booting up in building A gets its IP address from the DHCP server closer to it, in building A, while a machine booting up in building B gets an address from the DHCP server in building B. Since the two buildings will be linked and the network will be only one, will this work? How can I avoid that a machine booting up in building A gets an address from the DHCP server in building B (or vice versa)? Thanks.

    Read the article

  • Cannot Connect To VMWare Guest OS Using Either RDP or VNC

    - by Humanier
    Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

    Read the article

  • How do I format a text file for IIS Mailroot Pickup so that it sends an e-mail with attachments?

    - by Ben McCormack
    How do I need to format a text file so that it can be read by an SMTP service to send an e-mail that has an attachment? We have a server where we are using II6 SMTP to send mail from a Pickup folder. The goal is to drop a properly formatted text file into Mailroot\Pickup and then the file will be automatically processed and sent to the correct SMTP recipient. For simple files, this works correctly. Here's an example of a simple file that works (domain names changed): From:[email protected] To:[email protected] Subject:Hello World! Test Body Of The E-mail When I drop a text file containing the above contents into the Mailroot\Pickup folder, it sends correctly. However, I haven't been able to figure out how to get an attachment to work. I found some material that explained how to encode an SMTP attachment and another tool for simple base64 encoding conversion. Using the information on those pages, I came up with the following text: From:[email protected] To:[email protected] Subject:Hello World! MIME-Version: 1.0 Content-Type: text/plain; boundary="Attached" Content-Disposition: inline; --Attached Content-Transfer-Encoding: base64 Content-Type: text/plain; name="attachment.txt" Content-Disposition: attachment; filenamename="attachment.txt" VGhpcyBpcyBhIHRlc3Qgb2Ygc29tZXRoaW5nIHRvIGVuY29kZS4NCk5ldyBsaW5lDQpOZXcgTGlu ZQ0KIkhlbGxvdyIgISEhDQo9PT09ICcgZnNkZnNkZiAxMjM1NDU2MzQzNA== --Attached-- However, when I place the above text in a file and drop it into Mailroot\Pickup, it doesn't send an attachment correctly. Instead, an e-mail shows up with the following in the body of the e-mail: MIME-Version: 1.0 Content-Type: text/plain; boundary="Attached" Content-Disposition: inline; --Attached Content-Transfer-Encoding: base64 Content-Type: text/plain; name="attachment.txt" Content-Disposition: attachment; filenamename="attachment.txt" VGhpcyBpcyBhIHRlc3Qgb2Ygc29tZXRoaW5nIHRvIGVuY29kZS4NCk5ldyBsaW5lDQpOZXcgTGlu ZQ0KIkhlbGxvdyIgISEhDQo9PT09ICcgZnNkZnNkZiAxMjM1NDU2MzQzNA== --Attached-- I can't figure out what I need to do to format the text file so that the SMTP service correctly sends attachments.

    Read the article

  • Cannot Connect To VMWare Guest OS Using Either RDP or VNC

    - by Humanier
    Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

    Read the article

< Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >