Search Results

Search found 30127 results on 1206 pages for 'home network'.

Page 99/1206 | < Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• File/printer sharing issues on network with multiple OSes

  - by DanZ

  My workplace consists of computers running a variety of different operating systems, and I have been running into problems getting some of them to connect to a shared drive and printer over the network. Here is a brief description of the computers involved and the issues I have encountered: 1: Dell desktop, Windows Vista Business-- This is the computer I want the others to connect to. It has a USB printer and eSATA hard drive enclosure that I have set up for sharing, with different accounts for the various users. 2: Fujitsu laptop, Windows XP Tablet edition-- No problems. Can connect to both the shared printer and hard drive. 3: Lenovo laptop, Windows Vista Business 64 bit-- No problems. Can connect to both the shared printer and drive. 4: Apple MacBook, OS 10.4-- Can connect to the shared drive, but not to the shared printer. I am aware that the printer issue is due to a known incompatibility between Vista and OS 10.4 and earlier with regards to Samba. It is not a big problem, however, as this computer can access a network printer. 5: Sony laptop, Windows Vista Home Premium-- Can connect to the shared printer, but not the shared drive. It can see computer 1 and its shared drive on the network, and appears to successfully log in to user accounts. However, if you try to access the shared drive, it says you do not have permission. I have tried both standard and administrator accounts, and none can access the drive from this computer. 6: MacBook Pro, OS 10.5 (there are two of these)-- Can connect to the shared printer, but not the shared drive. They can't see computer 1 on the network. For that matter, they also can't see each other or the older Mac, but can see and access shared folders on the XP machine (computer 2) and can see other PCs in the building. I was able to add the shared printer manually by typing in its network location, but was unable to manually add the shared drive in the same way. So, what I am looking for is suggestions on how to get computers 5 and 6 to connect to the shared drive. Since they can already connect to the shared printer (which is on the same computer as the shared drive), it seems reasonable that they should be able to access the drive as well.

  Read the article

• Transient network dropout for Xen DomU's

  - by Stephen C

  We've got a CentOS server running a cluster of virtuals. Occasionally the cluster's internal network drops out for a minute or so ... and then comes back. The problem is somehow related to the actual network traffic, but it is not a simple load issue. (The system is generally lightly loaded, and the problem occurs irrespective of actual load.) The setup: CentOS 5.6 on Dom0, various CentOS on the DomU's Hardware - a Dell R710 with a BroadCom NextXpress 2 NIC (sigh) using the latest drivers for the NIC from BroadCom Xen configured to use network-bridge and vif-bridge Some iptable tweaks to route an unrelated port to one of the virtuals. The system has one externally visible IP address, and Dom0 runs an Apache httpd configured with a number of virtual hosts each of which reverse proxies to web servers running on the virtuals. (The virtuals have to be NAT'ed, primarily because we don't have enough allocated public IP addresses.) The symptoms: Works fine most of the time. When someone tries to UPLOAD a large file to one virtuals, the internal network drops out ... for all virtuals: The Dom0 httpd sees a network timeout talking to the backend server on the virtual and reports a 502. A previously established ssh connection from Dom0 to any of the DomU's freezes. Our monitoring shows ping failures for traffic between virtuals. The Xen consoles to the DomU's do not freeze. No log messages in any log files that I can see, on either Dom0 or the DomU's ... apart from the Dom0 httpd logs. After a minute or so, the problem clears by itself. This is 100% reproducible. What we've tried: Downloading, building and installing the latest BNX2 driver on Dom0 Turning off MSI on the NIC - adding "options bnx2 disable_msi=1" to /etc/modprobe.conf Turning off tcp segmentation offload - "ethtool -K eth0 tso off". Sacrificing a black rooster at midnight. I've exhausted all my options apart from switching to KVM ... or slaughtering more roosters. Any suggestions?

  Read the article

• Second network card configuration not working.

  - by Sebas

  I have 4 servers running Centos 5. All of them have two ethernet network cards. I have configured 192.168.1.x IP addresses on their eth0 card. They are all connected to the same switch using their eth0 card and they are all working. I have configured 10.72.11.x IP addresses on their eth1 card.They are all connected to the same switch - a different one from the switch used with eth0 card - using their eth1 card and they are NOT all working. Their configuration files is like: DEVICE=eth1 BOOTPROTO=static IPADDR=10.72.11.236 BROADCAST=10.72.11.191 NETMASK=255.255.255.192 NETWORK=10.72.11.128 HWADDR=84:2B:2B:55:4B:98 IPV6INIT=yes IPV6_AUTOCONF=yes ONBOOT=yes The interfase is starting and configured as I need. [root@sql1 network-scripts]# ifconfig eth0 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:97 inet addr:192.168.1.105 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::862b:2bff:fe55:4b97/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2981 errors:0 dropped:0 overruns:0 frame:0 TX packets:319 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:386809 (377.7 KiB) TX bytes:66134 (64.5 KiB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:98 inet addr:10.72.11.236 Bcast:10.72.11.191 Mask:255.255.255.192 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:48 Memory:dc000000-dc012800 I also added a route-eth1 file that looks like: 10.0.0.0/8 via 10.72.11.254 Routing looks fine to me: [root@sql1 network-scripts]# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.72.11.192 0.0.0.0 255.255.255.192 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.72.11.254 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 But I cannot ping one server from the other. [root@sql1 network-scripts]# ping 10.72.11.235 PING 10.72.11.235 (10.72.11.235) 56(84) bytes of data. From 10.72.11.236 icmp_seq=1 Destination Host Unreachable From 10.72.11.236 icmp_seq=2 Destination Host Unreachable From 10.72.11.236 icmp_seq=3 Destination Host Unreachable From 10.72.11.236 icmp_seq=4 Destination Host Unreachable From 10.72.11.236 icmp_seq=5 Destination Host Unreachable From 10.72.11.236 icmp_seq=6 Destination Host Unreachable ^C --- 10.72.11.235 ping statistics --- 7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6033ms , pipe 3 What am I doing wrong?

  Read the article

• D-Link DIR-300 slows down / loses network

  - by basic6

  there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

  Read the article

• Automation : Selenium iphone(Mobile) Driver To Capture Network using Xcode iPhone Simulator

  - by Sandeep

  I am using Xcode iPhone(Mobile) simulator to run Selenium iPhone WebDriver Automation scripts for mobile Websites. Is there anyway to capture Network-Traffic on iPhone simulator similar to Selenium RC Network capture or BrowserMob Proxy for Web Driver. Please let me know if you know way to capture Network traffic on iPhone simulator programmatically. I do see some tools like Wireshark or HTTPScoop to capture network traffic but I need in a pro grammatical way to automate. I need this scenario for pixel tracking. Thanks Sandeep

  Read the article

• Simulate Network Presence in dbus

  - by Evans

  Is there a way using Python to simulate the presence of an active network connection using dbus? If I call getstate() on the dbus, I'm able to get the current network state. I want to set the current state to 4 (Connection Present). This is because Network Manager is not able to connect using my modem and I use other tools to connect. Pidgin, Empathy and other software are not able to detect the network.

  Read the article

• Smallest sum of graph weight, where each node are connceted (like a network)

  - by Svisstack

  Hello, What algorithm I can use for problem like this: Have a graph positive weighted, i want to know a smallest possible sum of weights where each node are connected (connected like a network, where each node is a eg. network device). In this network each node can be connected with other node by some other other nodes in way. But all nodes from input graph must be in a network. Any one can help me with this?

  Read the article

• Mapping Drive Error - System Error 1808

  - by Julian Easterling

  A vendor is attempting to map and preserve a network drive using nt authority/system; so it stays persistent when the interactive session of the server is lost. They were able to do this on one server (Windows 2008 R2) but not a second computer (also Windows 2008 R2). D:\PsExec.exe -s cmd.exe PsExec v1.98 - Execute processes remotely Copyright (C) 2001-2010 Mark Russinovich Sysinternals - www.sysinternals.com Microsoft Windows [Version 6.1.7600] Copyright (c) 2009 Microsoft Corporation. all rights reserved. C:\Windows\system32>whoami nt authority\system C:\Windows\system32>net use New connections will be remembered. Status Local Remote Network -------------------------------------------------------------------- OK X: \\netapp1\share1 Microsoft Windows Network The command completed successfully. C:\Windows\system32>net use q: \\netapp1\share1 System error 1808 has occurred. The account used is a computer account. Use your global user account or local user account to access this server. C:\Windows\system32> I am unsure on how to set up a "machine account mapping" which will preserve the drive letter of the Netapp path being mapped, so that the service account running a Windows service can continue to access the share after interactive logon has expired on the server. Since they were able to do this on one server but not another, I'm not sure how to troubleshoot the problem? Any suggestions?

  Read the article

• Permission denied: /home/.htaccess pcfg_openfile: unable to check htaccess file

  - by phoebebright

  This domain was working this morning, now I get a 403 error and the message above in my error log. I'm not using .htaccess files but I have been doing some copy on the server so may have messed things up but no changes to this domain (unless by accident!). What is this pcfg_openfile thing anyway? Done lots of googleing but none of the solutions seemed to fit these circumstances. Server is ubuntu Hardy Heron.

  Read the article

• Existing open source software for wireless mesh networking?

  - by user70352

  Hello! My goal: Build a wireless mesh network with some ALIX 2D2 (500 MHz AMD Geode LX800 x86 CPU, 256MB RAM, Atheros wireless card) Aside from working like a normal wireless mesh network users should be able to read/write data from/to the ALIX Boxes and the ALIX boxes should be able to process data. Questions: Should I try to flash dd-wrt x86, voyage linux (linux.voyage.hk) or something else? What (open source) software should I look into before I start? Should I use a 'server' for data storage and processing instead of the ALIX boxes? Is it even possible to use the ALIX boxes for routing AND data storage and processing? Final notes: Data can be anything, for example, I want to setup a wireless mesh using the OLSRD protocol so my whole town gets wifi and can access songs on the network. It's not for that, but that's the idea. I'm not afraid of programing, compiling or working with *nix. This is mostly 'for fun' rather than for practicality. Thanks in advance for any feedback.

  Read the article

• "No more threads can be created in the system" in Network and Sharing Center

  - by Zell Faze

  A while back I noticed on one of our laboratory computers (Windows 7, very little extra software installed) that the network connection icon in the system tray would claim that it had no network connection, even though it did. This issue would go away after the computer was rebooted, but would surface again the next time I looked at the computer (a few days later). Upon opening the Network and Sharing Center I am shown an actual error message, but not one that seems to give me a lot of information about what the problem is. In the place of the usual information about network adapters and whether you are connected to the Internet it simply says: "No more threads can be created in the system." The Event Viewer shows hundreds of events from different services also with the same message. "Volume Shadow Copy Service error: Unexpected error calling routine CoCreateInstance. hr = 0x800700a4, No more threads can be created in the system."; "The WinHTTP Web Proxy Auto-Discovery Service service failed to start due to the following error: A thread could not be created for the service."; "The IP Helper service terminated with the following error: No more threads can be created in the system." As far as I can tell, this message seems to mean that there is some sort of resource leak in Windows where something is creating a large number of threads and those threads are not being killed off? I've tried restarting WMI and several services related to networking, without avail. Can anyone provide more information on what "No more threads can be created in the system" might mean and what I might be able to do to fix the issue? Currently the only solution appears to be restarting.

  Read the article

• Connection speed drops from 1 Gbps to 10 Mbps (Vista 64)

  - by Kevin Hakanson

  I recently got a Windows Home Server (HP MediaSmart Server EX490) setup so I could do backups and other things. However, I am having trouble on my Vista 64 PC. The backup will be making great progress, then it will just slow down. At one point, I noticed the lights on my Netgear GS105 indicated it was not using a 1000 Mbps connection, but a 10 Mbps one. I checked the Status of Local Area Connection (Intel(R) 82567V-2 Gigabit Network Connection) and that also showed the same slow speed. This has happened several times in the last couple days. When I disabled the network device, and then enabled it, it established the 1 Gpbs connection again. However, some of the times the Sent Bytes Activity on the Status windows indicate that the data flow is still slow (100 to 1000 bytes every couple seconds). Obviously, at this rate I could backup faster to floppy disk. :) My question is how to diagnose and fix this problem. When I look at the Administrative Events, I do a Errors: Bonjour Service 456: ERROR: read_msg errno 10054 (An existing connection was forcibly closed by the remote host.) And a Warning: e1yexpress Intel(R) 82567V-2 Gigabit Network Connection Link has been disconnected. I am suspicious there is some power saving mode. I found a post suggesting System Idle Power Saver(SIPS) may be the issue. I am going to try that, but looking for other suggestions or diagnostic advice. I have several new items in this configuration: server, client software, switch and cat6 cables.

  Read the article

• WRTU54G-TM T-Mobile@Home router with 3rd party firmware

  - by dlamblin

  I've been doing a lot of reading online about the Linksys WRTU54G-TM router model that I now own. It seems getting a custom firmware onto it is not a problem. But no one is talking about retaining the Voip features (yet). So far they're all disappointed that it's not a SIP machine and used GSM over IPSec. Personally I don't care about using it with non-t-mobile. If I take the original firmware, shouldn't I be able to extract it, and it's SquashFS image, and then move all of the t-mobile specific binaries for enabling the calling features over to a custom firmware installation (maybe OpenWRT)? You might ask why, and the reason is, that if I do this I could retain my calling features, which I do want, and ssh to the router and use it to run additional software, as any OpenWRT router could do. Does anyone know if this can be done, and how the firmware's binaries could be gotten at and installed correctly?

  Read the article

• Accessing network shares on Windows7 via SonicWall VPN client

  - by Jack Lloyd

  I'm running Windows7 x64 (fully patched) and the SonicWall 4.2.6.0305 client (64-bit, claims to support Windows7). I can login to the VPN and access network resources (eg SSH to a machine that lives behind the VPN). However I cannot seem to be able to access shared filesystems. Windows is refusing to do discovery on the VPN network. I suspect part of the problem is Windows persistently considers the VPN connection to be a 'public network'. Normally, you can open the network and sharing center and modify this setting, however it does not give me a choice for the VPN. So I did the expedient thing and turned on file sharing for public networks. I also disabled the Windows firewall for good measure. Still no luck. I can access the server directly by putting \\192.168.1.240 in the taskbar, which brings up the list of shares on the server. However, trying to open any of the shares simply tells me "Windows cannot access \\192.168.1.240\share You do not have permission to access ..."; it never asks for a domain password. I also tried Windows7 native VPN functionality - it couldn't successfully connect to the VPN at all. I suspect this is because SonicWall is using some obnoxious special/undocumented authentication system; I had similar problems trying to connect on Linux with the normal IPsec tools there. What magical invocation or control panel option am I missing that will let this work? Are there any reasonable debugging strategies? I'm feeling quite frustrated at Windows tendency to not give me much useful information that might let me understand what it is trying to do and what is going wrong.

  Read the article

• Intel Wireless 4965AGN not achieving N throughput when connected to an Airport Express N network

  - by BenA

  I have an Intel Wireless WiFi Link 4965AGN adaptor in my laptop (HP Pavillion dv2000 series) which is connecting to a 5Ghz-only 802.11n network provided by an Apple Airport Express. The network is using WPA2 encryption. My desktop is also connected the Airport, via a Linksys WUSB600N USB adaptor. Both are running with the latest drivers, and the Airport is running the latest firmware. The Airport is also configured to use wide channels. The problem I have is that I never get throughput above 4MB/s when transferring files between the two machines. Even a pessimistic calculation shows a 270Mbps network as being capable of transfer rates at well above 10MB/s. I'm pretty sure I've isolated the issue to being the Intel adaptor, as wiring the desktop to the AP, and using the Linksys adaptor on the laptop immediately yielded speeds limited by the 100MB/s ethernet connection. I know that 802.11n is still a draft standard, and so mixing kit from different manufacturers can easily lead to poor results, but I was just wondering if anybody else out there has had success with this Intel adaptor on an N network? Or even better, connecting it to an Airport Express? Can anybody give me any advice on how to troubleshoot this issue? I should also mention that the Airport Express doesn't allow you to manually specify channels when running in N mode, and that I've been able to rule out interference from other Wireless LANs by scanning. There aren't any other 5GHz networks in my area. All ideas welcome! Update: A while later, I've just updated to the most recent drivers for both the Intel chip in the laptop, and the USB adaptor. Unfortunately this hasn't improved things :(. If anybody has any advice it would be be gratefully received.

  Read the article

• Windows 8 unable to connect to WPA2 AES Wireless Network

  - by user170193

  I'm running Windows 8 and am unable to connect to my home wireless network. I've tried restarting the router, patching the drivers to the next version, patching the drivers to the last version, running windows update and patching the chipset drivers to the latest version. So far nothing has worked. My computer can get on the internet via USB tethering on my phone or an open WiFi connection, but it is unable to connect to my home WPA2 AES secured wireless network. It sees the network, attempts to connect, gets a limited connection and then drops the connection. All the other wireless devices in my household have no problems. I have the new Dell XPS 12, running Windows 8 using an Intel Centrino Advanced-N 6235 wireless adapter. I've refreshed windows twice now to try different driver configurations. I've tried uninstalling all the Dell software, I've tried uninstalling all the Intel software and reinstalling just the drivers. I've tried turning switching the ability for the Wireless driver to turn the computer off or on. I've tried setting up the connection manually from desktop mode. I've tried switching it on and off using the wireless button on the keyboard and in the software. So far nothing has allowed me to connect to the secured network. It just keeps getting a limited connection, dropping the connection and retrying. It's driving me crazy, any ideas, anything I missed? Thanks.

  Read the article

• DNS Piority in home-use Routers

  - by DucDigital

  Force DNS on router instead of ClientSide DNS like OpenDNS or GooglePublicDNS Im trying to implement some site blocking using DNS, the hardware is simple Routers like Linksys and Netgear that you use in house for family purpose. Currently I tried to set a computer to opendns, while my router set to something else, when check using opendns.com/welcome, the computer is identified as opendns. and Vice versa, this time the computer didn't identified as opendns. Is it posible to force user to use our DNS instead of their setting DNS?

  Read the article

• DNS Piority in home-use Routers

  - by DucDigital

  Force DNS on router instead of ClientSide DNS like OpenDNS or GooglePublicDNS Im trying to implement some site blocking using DNS, the hardware is simple Routers like Linksys and Netgear that you use in house for family purpose. Currently I tried to set a computer to opendns, while my router set to something else, when check using opendns.com/welcome, the computer is identified as opendns. and Vice versa, this time the computer didn't identified as opendns. Is it posible to force user to use our DNS instead of their setting DNS?

  Read the article

• Home CAT6 wiring: CMR vs CMP?

  - by Eddie Parker

  I'm planning on wiring my house with CAT6 cable. I'm finding a large jump in price between CMR and CMP cabling, and I'm confused by what counts as a 'plenum' and what does not. As I'm wiring my house, I'm planning on going through interior (hollow) walls, and through the attic and crawlspace to get to the points I wish to wire. I will be going between floors at one point, which leads me to believe I need at least CMR, and obviously CMP wouldn't hurt either. I don't mind spending the extra money if I need to, but is it overkill going for CMP if the bulk of the wires are either going vertical, or through a crawlspace or attic?

  Read the article

• Cisco SG 300-28P PoE switch appears to have damaged my domain server's network IF

  - by cdonner

  I just replaced the old HP ProCurve switch with a new Cisco SG 300-28P managed switch. It has PoE on all ports. Everything works, except for my domain server that went offline and the network interface appears to be dead. Windows says the network cable is disconnected, and no lights blink on the switch. Tried different cables and different ports on the switch. The Cisco PoE ports are supposed to be auto-sensing, i.e. not to send power to a device that cannot handle it. Is this technique not 100% reliable? The server is a SHUTTLE XS35V2 with an onboard network chip, so it is probably fried. My questions: is this plausible? who's fault is it - Shuttle or Cisco (i.e. which support line should I try first)? UPDATE: I did go back and tried another switch between the server and the Cisco switch, and indeed, the connection came back to live. When everything is powered down and I start fresh, with the server connected to the Cisco switch, the port light will blink for a while and the connection status is "No Internet connection" at first until it goes off after about 20 seconds and the connection status changes to "Network cable disconnected". On the other switch it works. Clearly not a PoE issue now. I will start looking into the Cisco's onboard diagnostic functions, but so far I have not noticed anything unusual in the log.

  Read the article

• pfsense 2.0.1 Firewall SMB Share not showing up under network

  - by atrueresistance

  I have a freenas NAS with a SMB share running at 192.168.2.2 of a 192.168.2.0/28 network. Gateway is 192.168.2.1. Originally this was running on a switch with my LAN, but now having upgraded to new hardware the Freenas has it's own port on the firewall. Before the switch the freenas would show up under Network on a windows 7 box and an OSX Lion box as freenas{wins} or CIFS shares on freenas{osx} so I know it doesn't have anything do to with the freenas. Here are my pfsense rules. ID Proto Source Port Destination Port Gateway Queue Schedule Description PASS TCP FREENAS net * LAN net 139 (NetBIOS-SSN) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 389 (LDAP) * none cifs lan passthrough PASS TCP FREENAS net * LAN net 445 (MS DS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 137 (NetBIOS-NS) * none cifs lan passthrough PASS UDP FREENAS net * LAN net 138 (NetBIOS-DGM) * none cifs lan passthrough BLOCK * FREENAS net * LAN net * * none BLOCK * FREENAS net * OPTZONE net * * none BLOCK * FREENAS net * 192.168.2.1 * * none PASS * FREENAS net * * * * none BLOCK * * * * * * none I can connect if I use \\192.168.2.2 and enter the correct login details. I would just like this to show up on the network. Nothing in the log seems to be blocked when I filter by 192.168.2.2. What port am I missing for SMB to show up under the network and not have to connect by IP? ps. Do I really need the LDAP rule?

  Read the article

• Vista home basic, "this folder is empty" problem

  - by peter m

  When I access my itunes folder in "my music" I see most but not all artist folders, when I access any of them I get "this folder is empty", When in Itunes all music plays and if I right click on a song and click show in folder I can see my full Itunes folder, so far I have done two system restores, scan disk, windows memory scan, defrag and tried ifixit. nothing has worked, I dont understand how I can see two different folders at the same address. Also have checked hidden files settings.

  Read the article

• Ripping a home video VCD on Linux or Windows with VLC or otherwise

  - by user259774

  I have a VCD with 22 minutes of video on it. I would like to retain this footage and throw away the VCD. I can play the whole thing with VLC ("open disc - vcd - /dev/sr0 - play"): all 22 minutes of the main track. I don't believe there's any other content aside from the main track. I can seek to anywhere I want to within the 22 minute track. If I mount /dev/sr0 /media/vcd and then try to copy the only file from the MPEGAV folder, I get an I/O error, with an empty destination file. VLC has a "convert" option in addition to "play". When I use this I actually get a good OGG file back, after it runs through the video in painful real-time. I guess it dubs it frame-by-frame. But the file is only 10 minutes long, leaving 12 minutes off of the track. Handbrake doesn't detect it's track titles, unfortunately. I don't know if I should start getting involved with GNU ddrescue or if it's because VCDs somehow encode their data sectors differently. Anyway, I'm in way over my head and if anyone knows how I could get that video track off the thing, feel free to share! Edit: I should note that I also have access to a Windows computer

  Read the article

• Looking for a list of compatible chipset, mobo with Windows Home Server/Windows 2003

  - by ronaldwidha

  I'm building a WHS and looking into finding a mini atx mobo for Pentium E5300 socket 775. I have a couple of mobo in mind and would like to check them against a list of compatible mobo/chipset with WHS/WIndows Server 2003. I've found http://www.windowsservercatalog.com/ but unfortunately it doesn't contain any mobo/chipset. Anyone know of such compatibility list?

  Read the article

< Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >