Search Results

Search found 13537 results on 542 pages for 'installation failure'.

Page 99/542 | < Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >

• linux raid 1: right after replacing and syncing one drive, the other disk fails - understanding what is going on with mdstat/mdadm

  - by devicerandom

  We have an old RAID 1 Linux server (Ubuntu Lucid 10.04), with four partitions. A few days ago /dev/sdb failed, and today we noticed /dev/sda had pre-failure ominous SMART signs (~4000 reallocated sector count). We replaced /dev/sdb this morning and rebuilt the RAID on the new drive, following this guide: http://www.howtoforge.com/replacing_hard_disks_in_a_raid1_array Everything went smooth until the very end. When it looked like it was finishing to synchronize the last partition, the other old one failed. At this point I am very unsure of the state of the system. Everything seems working and the files seem to be all accessible, just as if it synchronized everything, but I'm new to RAID and I'm worried about what is going on. The /proc/mdstat output is: Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md3 : active raid1 sdb4[2](S) sda4[0] 478713792 blocks [2/1] [U_] md2 : active raid1 sdb3[1] sda3[2](F) 244140992 blocks [2/1] [_U] md1 : active raid1 sdb2[1] sda2[2](F) 244140992 blocks [2/1] [_U] md0 : active raid1 sdb1[1] sda1[2](F) 9764800 blocks [2/1] [_U] unused devices: <none> The order of [_U] vs [U_]. Why aren't they consistent along all the array? Is the first U /dev/sda or /dev/sdb? (I tried looking on the web for this trivial information but I found no explicit indication) If I read correctly for md0, [_U] should be /dev/sda1 (down) and /dev/sdb1 (up). But if /dev/sda has failed, how can it be the opposite for md3 ? I understand /dev/sdb4 is now spare because probably it failed to synchronize it 100%, but why does it show /dev/sda4 as up? Shouldn't it be [__]? Or [_U] anyway? The /dev/sda drive now cannot even be accessed by SMART anymore apparently, so I wouldn't expect it to be up. What is wrong with my interpretation of the output? I attach also the outputs of mdadm --detail for the four partitions: /dev/md0: Version : 00.90 Creation Time : Fri Jan 21 18:43:07 2011 Raid Level : raid1 Array Size : 9764800 (9.31 GiB 10.00 GB) Used Dev Size : 9764800 (9.31 GiB 10.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:27:33 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : a3b4dbbd:859bf7f2:bde36644:fcef85e2 Events : 0.7704 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 1 - faulty spare /dev/sda1 /dev/md1: Version : 00.90 Creation Time : Fri Jan 21 18:43:15 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:39:06 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 8bcd5765:90dc93d5:cc70849c:224ced45 Events : 0.1508280 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 18 1 active sync /dev/sdb2 2 8 2 - faulty spare /dev/sda2 /dev/md2: Version : 00.90 Creation Time : Fri Jan 21 18:43:19 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:46:44 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 2885668b:881cafed:b8275ae8:16bc7171 Events : 0.2289636 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 19 1 active sync /dev/sdb3 2 8 3 - faulty spare /dev/sda3 /dev/md3: Version : 00.90 Creation Time : Fri Jan 21 18:43:22 2011 Raid Level : raid1 Array Size : 478713792 (456.54 GiB 490.20 GB) Used Dev Size : 478713792 (456.54 GiB 490.20 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 3 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:19:20 2013 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 0 0 1 removed 2 8 20 - spare /dev/sdb4 The active sync on /dev/sda4 baffles me. I am worried because if tomorrow morning I have to replace /dev/sda, I want to be sure what should I sync with what and what is going on. I am also quite baffled by the fact /dev/sda decided to fail exactly when the raid finished resyncing. I'd like to understand what is really happening. Thanks a lot for your patience and help. Massimo

  Read the article

• Installing Ubuntu: root failed on restart

  - by Jokerboy

  I just installed Ubuntu. At the end, it tells me to keep away the CD and to restart. After I restart it tells me: searching for boot record form ide-0..not found searching for boot record form cdrom..not found root failure press any key to continue reboot or select proper boot device. I have just one CD-ROM and one IDE hard drive.

  Read the article

• My PC suddenly doesn't detect the primary drive (SSD)

  - by smoth190

  My computer has been working fine for months, and it worked today, but tonight I went to start it up to find that my OCZ Vertex 2 isn't being found. When I turn on my computer, the loading screen gets stuck at "Detecting IDE drives...". After a while, it keeps going and lists the drives it finds. The first one in the list should be my Vertex 2, but it just says "None". The computer proceeds to get stuck on "Loading operating system...", which is understandable because the drive with the OS is "gone". My first thought was drive failure, but every time drives have crashed on me, they're still detected--they just don't work. This drive is an SSD, it's pretty new, and I had no problems beforehand. I find it hard to believe it failed. I'm sure it's possible, but I hope this isn't the case. There has been nothing strange going on at all with my PC, it's been running perfect until now. I was just about to do my monthly dskchk and defrag today. I popped in my Windows 7 Home Premium disk and booted from it. When I launched the repair tool, it didn't list any operating systems (because the drive is 100% missing...). When I've had disks crash before, it still listed the OS, you just couldn't do anything with it. I tried to restore from an image, but I don't have any of those, either. I opened the command console and listed the drivers with wmic logicaldisk get name. Only C: and D: came up. C: was my 1TB storage driver (luckily, all my stuff is here--only the OS is on the SSD!) and D: was the disk driver. So I still had an MIA drive... The SSD didn't come with any driver disks, so I can't install drivers. If there's a way to do this from a CD I can burn with my other PC, please let me know. What the heck do I do? Although only the OS is on my SSD, a new SSD is expensive. I'll probably also have to buy a new copy of Windows (an upgrade would be nice, though...) because I've found it eats my registration key when my PC crashes (and my thousands of dollars of Adobe programs, I'll be on the phone with tech support for a week to get those keys back). And I'll lose my registry, all my settings, all sorts of other stuff that I'll spend weeks restoring. My computer is a pain in the butt to take out and open up, so if I can't fix it, I'll try fiddling with the plug or putting it into a new computer, but not right now. Any help is greatly appreciated! The day when they make crash-less drives will be the day I live without worry.

  Read the article

• A failed disk (Pay for professional service or SpinRite?)(new edit)

  - by huggie

  EDIT: After much negotiating and begging and seeing through promotion smoke screen, thanks to the nice representative who took my case, I now know that the engineer has already fixed my NTFS partition (I guess it might be a bad block in the partition table?). She told me that the problem was considered minor, and I should be able to boot normally and just copy stuff out. Whew..I'm glad I didn't agree to the NTD $16,000 deal. New question (should this be in a new thread?): is it safer to use the linux "dd" command or is it better to boot normally into Windows XP and just copy stuff out? EDIT2: Thanks to all the help. I give the best answer to Console as it's most directed related to my question. But many suggestion are helpful and informational. ---- ORIGINAL POST BELOW --- Hi, in my previous post (You don't need to read but it's at http://superuser.com/questions/48838/windows-xp-a-disk-read-error-occurred), I said that my hard disk was not booting and is showing "a disk read error occurred". I took it to a recovery professional. A representative responded today told me that the NTFS partitions have a "NTFS partition system crash". I have no idea what that means. The engineer handling my drive will not be available for contact till tomorrow. Now the company charges me NTD (New Taiwan Dollar) $16,000 to recover lost data, that's kind of a lot considering that my graduate student monthly stipend is currently NTD $32,000 (max. allowed by regulation, may be lower, may change depend on funding). Now I'm weighting in between the options. Option A: let the professional recovers it with the half of my monthly stipend. If file/directories I designated are not recovered I don't pay a penny. (other than the initial examination fee of NTD $1000 which I've already paid.) Option B: let me try SpinRite, if failed, back to Option A. I spoke to the representative at the company they recommended me not to handle it on my own (yeah of course that's what they all want to say, right?), and at the price tag the disk error is probably relatively minor and data recoverable. But the representative really did not have detailed information of the disk failure so I didn't take her recommendation readily. Though one thing I heed was that she said that what they would do is to duplicate the disk before attempting discovery, so there would be no data loss (Is this true? can't duplicating invoke further data loss?). That sounds very good to me. Or maybe a third option: Option C: Negotiate with them to pay them to duplicate the disk hopefully for a much smaller price tag. Let me try SpinRite, if failed, back to Option A. This is a difficult decision. Ultimately I want my data back, but if a cheaper way is available to achieve the same thing... Can operating with SpinRite also corrupt data in someway? I've no idea what happened to my drive. I'll attempt to contact the engineer and hope to get it clarified and make an edit here.

  Read the article

• Write-error on swap-device, Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK

  - by Jan

  My root server at 1&1 was unresponsive on HTTP and SSH, so I logged into the serial console . It flooded my connection with endless error messages like quoted below. I initiated a reboot and now everything seems to work properly. After googling, I installed smartctl and ran a short self test, which told me the device was healthy. Is this likely a disk failure soon to happen or could it be just some program going wild? I assume, the swap device could also grow full when huge amounts of memory get consumed by a buggy program? How can I find out for sure? The sever was already unresponsive a week ago when I just restarted it without proper investigation. The server is running on CentOS. Write-error on swap-device (8:16:8351055) Write-error on swap-device (8:16:8351063) Write-error on swap-device (8:16:8351071) Write-error on swap-device (8:16:8351079) Write-error on swap-device (8:16:8351087) Write-error on swap-device (8:16:8351095) Write-error on swap-device (8:16:8351103) Write-error on swap-device (8:16:8351111) Write-error on swap-device (8:16:8351119) Write-error on swap-device (8:16:8351127) Write-error on swap-device (8:16:8351135) Write-error on swap-device (8:16:8351143) Write-error on swap-device (8:16:8351151) Write-error on swap-device (8:16:8351159) Write-error on swap-device (8:16:8351167) Write-error on swap-device (8:16:8351175) Write-error on swap-device (8:16:8351183) Write-error on swap-device (8:16:8351191) sd 1:0:0:0: [sdb] Unhandled error code sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK sd 1:0:0:0: [sdb] CDB: Write(10): 2a 00 00 9c 00 ef 00 00 08 00 end_request: I/O error, dev sdb, sector 10223855 Write-error on swap-device (8:16:10223863) sd 1:0:0:0: [sdb] Unhandled error code sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK sd 1:0:0:0: [sdb] CDB: Write(10): 2a 00 00 9c 0e 97 00 00 10 00 end_request: I/O error, dev sdb, sector 10227351 Write-error on swap-device (8:16:10227359) Write-error on swap-device (8:16:10227367) sd 1:0:0:0: [sdb] Unhandled error code sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK sd 1:0:0:0: [sdb] CDB: Write(10): 2a 00 00 9c b0 1f 00 00 10 00 end_request: I/O error, dev sdb, sector 10268703 Write-error on swap-device (8:16:10268711) Write-error on swap-device (8:16:10268719) sd 1:0:0:0: [sdb] Unhandled error code sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK sd 1:0:0:0: [sdb] CDB: Write(10): 2a 00 00 a0 84 7f 00 00 08 00 end_request: I/O error, dev sdb, sector 10519679 Write-error on swap-device (8:16:10519687) sd 1:0:0:0: [sdb] Unhandled error code sd 1:0:0:0: [sdb] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK sd 1:0:0:0: [sdb] CDB: Write(10): 2a 00 00 a7 26 af 00 04 00 00 end_request: I/O error, dev sdb, sector 10954415 Write-error on swap-device (8:16:10954423) Write-error on swap-device (8:16:10954431) Write-error on swap-device (8:16:10954439) Write-error on swap-device (8:16:10954447) Write-error on swap-device (8:16:10954455) Write-error on swap-device (8:16:10954463) Write-error on swap-device (8:16:10954471) Write-error on swap-device (8:16:10954479) Write-error on swap-device (8:16:10954487) Write-error on swap-device (8:16:10954495) Write-error on swap-device (8:16:10954503) Write-error on swap-device (8:16:10954511) Write-error on swap-device (8:16:10954519) Write-error on swap-device (8:16:10954527) Write-error on swap-device (8:16:10954535) Write-error on swap-device (8:16:10954543) Write-error on swap-device (8:16:10954551) Write-error on swap-device (8:16:10954559) Write-error on swap-device (8:16:10954567) Write-error on swap-device (8:16:10954575) Write-error on swap-device (8:16:10954583) Write-error on swap-device (8:16:10954591) Write-error on swap-device (8:16:10954599) Write-error on swap-device (8:16:10954607) Write-error on swap-device (8:16:10954615) Write-error on swap-device (8:16:10954623) Write-error on swap-device (8:16:10954631) Write-error on swap-device (8:16:10954639) Write-error on swap-device (8:16:10954647) Write-error on swap-device (8:16:10954655) Write-error on swap-device (8:16:10954663) Write-error on swap-device (8:16:10954671) Write-error on swap-device (8:16:10954679) Write-error on swap-device (8:16:10954687) Write-error on swap-device (8:16:10954695) Write-error on swap-device (8:16:10954703) Write-error on swap-device (8:16:10954711) Write-error on swap-device (8:16:10954719) Write-error on swap-device (8:16:10954727) Write-error on swap-device (8:16:10954735) Write-error on swap-device (8:16:10954743) Write-error on swap-device (8:16:10954751) Write-error on swap-device (8:16:10954759) Write-error on swap-device (8:16:10954767) Write-error on swap-device (8:16:10954775) Write-error on swap-device (8:16:10954783) Write-error on swap-device (8:16:10954791) Write-error on swap-device (8:16:10954799) Write-error on swap-device (8:16:10954807) Write-error on swap-device (8:16:10954815) Write-error on swap-device (8:16:10954823) Write-error on swap-device (8:16:10954831) Write-error on swap-device (8:16:10954839) Write-error on swap-device (8:16:10954847) Write-error on swap-device (8:16:10954855) Write-error on swap-device (8:16:10954863) Write-error on swap-device (8:16:10954871) Write-error on swap-device (8:16:10954879) Write-error on swap-device (8:16:10954887) Write-error on swap-device (8:16:10954895) Write-error on swap-device (8:16:10954903) Write-error on swap-device (8:16:10954911) Write-error on swap-device (8:16:10954919) Write-error on swap-device (8:16:10954927) Write-error on swap-device (8:16:10954935) Write-error on swap-device (8:16:10954943) Write-error on swap-device (8:16:10954951) Write-error on swap-device (8:16:10954959) Write-error on swap-device (8:16:10954967) Write-error on swap-device (8:16:10954975) Write-error on swap-device (8:16:10954983) Write-error on swap-device (8:16:10954991) Write-error on swap-device (8:16:10954999) Write-error on swap-device (8:16:10955007) Write-error on swap-device (8:16:10955015) Write-error on swap-device (8:16:10955023) Write-error on swap-device (8:16:10955031) Write-error on swap-device (8:16:10955039) Write-error on swap-device (8:16:10955047) Write-error on swap-device (8:16:10955055) Write-error on swap-device (8:16:10955063) Write-error on swap-device (8:16:10955071) Write-error on swap-device (8:16:10955079) Write-error on swap-device (8:16:10955087) Write-error on swap-device (8:16:10955095) Write-error on swap-device (8:16:10955103) Write-error on swap-device (8:16:10955111) Write-error on swap-device (8:16:10955119) Write-error on swap-device (8:16:10955127) Write-error on swap-device (8:16:10955135) Write-error on swap-device (8:16:10955143) Write-error on swap-device (8:16:10955151) Write-error on swap-device (8:16:10955159) Write-error on swap-device (8:16:10955167) Write-error on swap-device (8:16:10955175) Write-error on swap-device (8:16:10955183)

  Read the article

• Macports irssi & perl5 installation issues

  - by Dmitri DB

  Long time reader, first time poster. Big, appreciative thanks for everyone's collective questioning and answering here and at stackoverflow, it's helped me quite a lot over the time I've been learning answers through these sites! Apologies in advance if I didn't search hard enough on posts already up on this site to find out what I could do about this issue, but I thought I'd just reach out for the sake of trying at least once. I've experienced this issue while starting up my macports-installed version of irssi: 13:25 -!- Irssi: Error in script dispatch: 13:25 Can't locate lib.pm in @INC (@INC contains: /opt/local/lib/perl5/site_perl/5.12.4/darwin-multi-2level /opt/local/lib/perl5/site_perl/5.12.4 /opt/local/lib/perl5/vendor_perl/5.12.4/darwin-multi-2level /opt/local/lib/perl5/vendor_perl/5.12.4 /opt/local/lib/perl5/5.12.4/darwin-multi-2level /opt/local/lib/perl5/5.12.4 /opt/local/lib/perl5/site_perl/5.12.3/darwin-multi-2level /opt/local/lib/perl5/site_perl/5.12.3 /opt/local/lib/perl5/site_perl /opt/local/lib/perl5/vendor_perl .) at (eval 18) line 1. 13:25 BEGIN failed--compilation aborted at (eval 18) line 1. 13:25 Huh, strange. I looked into it a bit: [email protected] /opt/local/lib/perl5 ?- find . -name "lib.pm" -ls 14673887 16 -r--r--r-- 1 root admin 6853 25 Jun 23:39 ./5.12.4/darwin-thread-multi- 2level/lib.pm [email protected] /opt/local/lib/perl5 ?- l 5.12.4/darwin-thread-multi-2level total 1864 drwxr-xr-x 55 root admin 1870 28 Jun 19:28 . drwxr-xr-x 158 root admin 5372 28 Jun 19:28 .. -rw-r--r-- 1 root admin 177814 25 Jun 23:39 .packlist drwxr-xr-x 6 root admin 204 28 Jun 19:28 B -r--r--r-- 1 root admin 25714 25 Jun 23:39 B.pm drwxr-xr-x 64 root admin 2176 28 Jun 19:28 CORE drwxr-xr-x 3 root admin 102 28 Jun 19:28 Compress -r--r--r-- 1 root admin 3000 25 Jun 23:39 Config.pm -r--r--r-- 1 root admin 228094 25 Jun 23:39 Config.pod -r--r--r-- 1 root admin 409 25 Jun 23:39 Config_git.pl -r--r--r-- 1 root admin 38759 25 Jun 23:39 Config_heavy.pl -r--r--r-- 1 root admin 21174 25 Jun 23:39 Cwd.pm -r--r--r-- 1 root admin 63535 25 Jun 23:39 DB_File.pm drwxr-xr-x 3 root admin 102 28 Jun 19:28 Data drwxr-xr-x 5 root admin 170 28 Jun 19:28 Devel drwxr-xr-x 4 root admin 136 28 Jun 19:28 Digest -r--r--r-- 1 root admin 25185 25 Jun 23:39 DynaLoader.pm drwxr-xr-x 22 root admin 748 28 Jun 19:28 Encode -r--r--r-- 1 root admin 29731 25 Jun 23:39 Encode.pm -r--r--r-- 1 root admin 6736 25 Jun 23:39 Errno.pm -r--r--r-- 1 root admin 5445 25 Jun 23:39 Fcntl.pm drwxr-xr-x 5 root admin 170 28 Jun 19:28 File drwxr-xr-x 3 root admin 102 28 Jun 19:28 Filter -r--r--r-- 1 root admin 1819 25 Jun 23:39 GDBM_File.pm drwxr-xr-x 4 root admin 136 28 Jun 19:28 Hash drwxr-xr-x 3 root admin 102 28 Jun 19:28 I18N drwxr-xr-x 11 root admin 374 28 Jun 19:28 IO -r--r--r-- 1 root admin 1404 25 Jun 23:39 IO.pm drwxr-xr-x 6 root admin 204 28 Jun 19:28 IPC drwxr-xr-x 4 root admin 136 28 Jun 19:28 List drwxr-xr-x 4 root admin 136 28 Jun 19:28 MIME drwxr-xr-x 3 root admin 102 28 Jun 19:28 Math -r--r--r-- 1 root admin 2519 25 Jun 23:39 NDBM_File.pm -r--r--r-- 1 root admin 4208 25 Jun 23:39 O.pm -r--r--r-- 1 root admin 15563 25 Jun 23:39 Opcode.pm -r--r--r-- 1 root admin 21011 25 Jun 23:39 POSIX.pm -r--r--r-- 1 root admin 58962 25 Jun 23:39 POSIX.pod drwxr-xr-x 5 root admin 170 28 Jun 19:28 PerlIO -r--r--r-- 1 root admin 2515 25 Jun 23:39 SDBM_File.pm drwxr-xr-x 4 root admin 136 28 Jun 19:28 Scalar -r--r--r-- 1 root admin 10837 25 Jun 23:39 Socket.pm -r--r--r-- 1 root admin 41003 25 Jun 23:39 Storable.pm drwxr-xr-x 4 root admin 136 28 Jun 19:28 Sys drwxr-xr-x 3 root admin 102 28 Jun 19:28 Text drwxr-xr-x 5 root admin 170 28 Jun 19:28 Time drwxr-xr-x 3 root admin 102 28 Jun 19:28 Unicode -r--r--r-- 1 root admin 14462 25 Jun 23:39 attributes.pm drwxr-xr-x 38 root admin 1292 28 Jun 19:28 auto -r--r--r-- 1 root admin 19892 25 Jun 23:39 encoding.pm -r--r--r-- 1 root admin 6853 25 Jun 23:39 lib.pm -r--r--r-- 1 root admin 11044 25 Jun 23:39 mro.pm -r--r--r-- 1 root admin 997 25 Jun 23:39 ops.pm -r--r--r-- 1 root admin 13945 25 Jun 23:39 re.pm drwxr-xr-x 3 root admin 102 28 Jun 19:28 threads -r--r--r-- 1 root admin 33283 25 Jun 23:39 threads.pm So, it sort of seems to me that the permissions which perl5 got installed with for these modules has gotten mixed up somehow? I'm not really a perl user beyond enjoying it for massive directory-recursive find/replace operations within text files, so I haven't much of an idea what the permissions here are supposed to look like, and I'm not really sure how to go about determining how macports has gone and installed perl this way when it's otherwise worked without failure for years now. Does anyone have any recommendations for the sanest path towards rectifying this issue? Also, is there any interesting reason as to why the macports default for the perl5 port installs 5.12.4, and not 5.16.0, which has to be explicitly installed via the perl5.16 port? Thanks again!

  Read the article

• CentOS 5.7 keeps rebooting after fresh installation

  - by Wagner Maestrelli

  I have just installed CentOS 5.7 x86_64 on a new computer. The installation went on without any issues. But, after it finnished, the machine started to show an awkward behaviour: it restarts every time it tries to boot. It happens after all the services have been started. The screen just goes black and it shows an error message from the monitor: Input not supported. And then it reboots. I took a look at the logs, but I couldn't manage to find anything. Any help? Update Before doing the hardware diagnosis, as pointed out, I decided to make some tests. First, I changed the runlevel to 3, adding the 3 parameter at the end of the kernel command. Then, after logging in in text mode, I checked the xorg.conf file out for some problems regarding the screen resolution. There was nothing unexpected set. Well, if there had to be a problem with it, I couldn't start the X server at the command line, right? So, I typed startx and Gnome started! So, probably, it's not an issue with the screen resolution, I suppose. Then I selected the Log Out root... Gnome menu option and something odd happened: the screen went black, the Input not supported monitor error message was displayed and the system rebooted. Yes, the same problem I was having while trying to boot! After that, I decided to try yet another test: I removed the rhgb quiet parameters from the kernel command to see if some error would show up. Well, to my surprise, the boot went on without problems! The Gnome login screen showed up, I logged in and the session started. But then I selected the Shut Down... menu option and guess what? Same problem: black screen, same monitor error and the system rebooted. Yes, it rebooted, it did not shut down. I repeated both of the tests and the behaviours were the same. I really don't know what's going on. It seems to be an issue regarding the changing of the screen mode or something like that. Any ideas? Could this be a hardware problem? Or does it seem to be something regarding the system configuration?

  Read the article

• HP F2180 driver installation fails on 64-bit Windows 7

  - by Noam Gal

  Hello; I am trying to install the HP Deskjet AIO (non-network) driver on my machine, which is running the 64-bit version of Windows 7. Before installing it, Windows detected my printer just fine... But I wanted to use the HP scanning application, because tt allows me to scan several photos at once. I ran the DJ_AIO_NonNetwork_ENU_NB file I got from their site, and the installation went almost without a problem... However, at the part where it should have detected the printer, it didn't, so I skipped it - telling the installer I'll connect the printer later. After it was finished I was able to use it regularly, and also scan using the wanted HP application. However, the installer kept popping at random intervals, and giving me an error message. Yesterday I tried removing all the installed HP Applications, and installing from scratch. Running the same installer setup, it now insists that it does not support my operating system, and that 64-bit Vista is the highest it can go... I just don't understand why this is occuring all of the sudden. Has anybody here successfully installed the AIO driver on the 64-bit version of Windows 7? UPDATE: Been chatting with HP chat support over the weekend. Managed to really mess up my windows. At first, they told me to uninstall using an "unintall_l3" batch file inside their installer package, and then reinstall. Didn't work. Also the "l4" batch didn't make any difference. Afterwards I was told to install "Windows install clean up" and remove many hp entries (most of which were not listed on my computer), and I also removed many other hp entries I bumped upon. Then my office 2k7 started failing. I searched around the web, and ran Security Restore, so now my office works, but my windows explorer is all buggy - can't seem to open windows explorer - it hangs while trying to load my hard drives, or completely ignores them and just shows my libraries. Anyone here has any idea how I can restore my win7 to normal, with or without the annoying scanner? UPDATE 2: Ok - explorer back to normal. I guess I just had to wait until it finishes searching while opening the windows explorer for the first time after the Security Restore. Scanner still not working though.

  Read the article

• Nvidia Drivers on Debian / Lenny (Stable) -> Installation successful -> Monitors gets black

  - by David

  I have successfully installed the proprietary drivers for my nvidia (geforce 7300 gt) graphics card on debian/lenny. I know its not the best way to chose for driver installation ( see this link: http://wiki.debian.org/NvidiaGraphicsDrivers#non-freedrivers ). but the two ways seem to be possible for me (nvidia-kernel module compilation). Now the problem is that the monitors gets black, the power light starts blinking after i launch the x-server. Have a short look a the logs (output truncated from /var/log/Xorg.0.log): (II) Setting vga for screen 0. (**) NVIDIA(0): Depth 24, (--) framebuffer bpp 32 (==) NVIDIA(0): RGB weight 888 (==) NVIDIA(0): Default visual is TrueColor (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0) (**) Jul 28 17:10:11 NVIDIA(0): Enabling RENDER acceleration (II) Jul 28 17:10:11 NVIDIA(0): Support for GLX with the Damage and Composite X extensions is (II) Jul 28 17:10:11 NVIDIA(0): enabled. (II) Jul 28 17:10:11 NVIDIA(0): NVIDIA GPU GeForce 7300 GT (G73) at PCI:1:0:0 (GPU-0) (--) Jul 28 17:10:11 NVIDIA(0): Memory: 262144 kBytes (--) Jul 28 17:10:11 NVIDIA(0): VideoBIOS: 05.73.22.25.00 (II) Jul 28 17:10:11 NVIDIA(0): Detected PCI Express Link width: 16X (--) Jul 28 17:10:11 NVIDIA(0): Interlaced video modes are supported on this GPU (--) Jul 28 17:10:11 NVIDIA(0): Connected display device(s) on GeForce 7300 GT at PCI:1:0:0: (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0) (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (CRT-0): 400.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): 165.0 MHz maximum pixel clock (--) Jul 28 17:10:11 NVIDIA(0): Samsung SyncMaster (DFP-0): Internal Single Link TMDS (II) Jul 28 17:10:11 NVIDIA(0): Assigned Display Device: CRT-0 (==) Jul 28 17:10:11 NVIDIA(0): (==) Jul 28 17:10:11 NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select" (==) Jul 28 17:10:11 NVIDIA(0): will be used as the requested mode. (==) Jul 28 17:10:11 NVIDIA(0): (II) Jul 28 17:10:11 NVIDIA(0): Validated modes: (II) Jul 28 17:10:11 NVIDIA(0): "nvidia-auto-select" (II) Jul 28 17:10:11 NVIDIA(0): Virtual screen size determined to be 1280 x 1024 (--) Jul 28 17:10:11 NVIDIA(0): DPI set to (85, 86); computed from "UseEdidDpi" X config (--) Jul 28 17:10:11 NVIDIA(0): option (==) Jul 28 17:10:11 NVIDIA(0): Enabling 32-bit ARGB GLX visuals. (--) Depth 24 pixmap format is 32 bpp Here is the complete /etc/X11/xorg.conf file as generated by nvidia-xconfig: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:59 PDT 2010 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "Module" Load "dbe" Load "extmod" Load "type1" Load "freetype" Load "glx" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" Hor

  Read the article

• Reinstall Acer OEM Windows 8, Windows 8 Recovery for Acer Aspire V5 122p

  - by stwindr

  My Acer Aspire V5-122P-61456G50NSS, model - MS2377, has crashed all together. It came preloaded with Windows 8 and I upgraded to windows 8.1 3-4 days before crash. Unfortunately I did not make any recovery media before the crash. While accessing the eRecovery on Acer store with my PC's serial no. it says nor RCD available for this. I tried recovery by loading recovery manager (Left Alt + F10) Various other advanced startup options (like holding shift key while turning on or pressing F8 key) returns nothing but no luck. However I am able to enter BIOS. After doing research on above condition on various PC forums, now my questions: I read that a 'Windows Recovery Drive' can be made on any PC running Windows 8 and could be used to repair another PC. Does anybody in SuperUser community have that (or a link to download the same from somewhere? as I'm unable to find anybody running windows 8 among my friends). I downloaded a window 8 Pro ISO and made a bootable USB. I was able to go to 'Repair Your Computer' option and after going to 'Reset your PC' option found that my recovery partition has gone/missing. I tried all options available but no luck. Then I tried to install with that Windows 8 Pro ISO but got message: "The product key entered does not match any of the Windows images available for installation. Enter a different product key". before this message I did not got any form to fill product key! Does this mean that the installer was picking up the key from BIOS (OEM Key)? and may be the installation did not succeeded because OEM Windows version was Window 8 and I was trying to install Windows 8 Pro. If that is the case then, could somebody please send me link to download an Windows 8 ISO? I am helpless and couldn't find anywhere on internet (without having to pay for a new key, but I should not pay as the installer will use OEM key).

  Read the article

• How do I install the latest version of packages in Ubuntu?

  - by Roman

  For example I want to install the latest version of "numpy". I type the following: "sudo apt-get install python-numpy". When I type this the first time it installs something and if I type this the second time it writes that I have already the latest version of numpy. However, I see that my version of numpy is 1.1.1. and I know that it NOT the latest version. Why it happens and how this problem can be solved? I can find the *tar.gz file with the latest version, I can extract files with the archive and than I need to rune one of the scripts which will be somewhere among the extracted files. But I do not like this way. It is too complicated. I do not know where I should put all these files, I do not know which dependencies I should install before I run the script for the installation of numpy, I do not know where numpy will be put after installation and so on. Is there an easy way to get the latest version of numpy?

  Read the article

• Group Policy Software Installs Too Silent on Windows 7

  - by jonblock

  I'm trying to migrate a Windows XP deployment process to Windows 7. The process has been surprisingly smooth, after figuring out how to bring up a base system. We rely heavily on Group Policy software installation, which in XP can mean long periods on any given morning sitting around watching the machine install new updates. At least the typical Windows Installer message shows the user that something is indeed happening. As far as I can tell, Windows 7 retains the startup installation process (good), but eliminates the on-screen message to indicate what's happening (bad). All a user will see, possibly for a half-hour or more if they haven't restarted for a while, is the electric hamster wheel and the words "Please wait...". I forsee a significant increase in support calls... If you're familiar with msiexec.exe parameters, XP behaves like /qb-, and 7 behaves like /qn. I want the /qb- behavior back. Is there a way to re-enable the Windows Installer notices for Group Policy startup installations?

  Read the article

• RHEL 5.2 installing on ProLiant BL460c - hangs at 'now booting the kernel'

  - by Dr Rocket Mr Socket

  As the title states, I have a problem. This server and the installation disc are also on the other side of the world to me so... So far, I have tried to start the install with the parameters: linux text noapic noacpi no=apic no=acpi which results in the same hang. I have also disabled a PCI ethernet adapter, I am uneasy about disabling the onboard ethernet adapter I do not know if ILO uses this. Anyone have any advice? Much appreciated. EDIT: full output after trying to begin the installation. boot: linux text Loading initrd.img.................. Loading vmlinuz....... Uncompressing Linux...done. Now booting the kernel stays on this for hours EDIT2: adding the 'mem=40960M' (server has 40 gigs of ram) parameter allows it to proceed but the following output directly after 'Now booting the kernal' Memory: sized by int13 0e801h initrd extends beyond end of memory (0x00ef2090 > 0x00000000) disabling initrd Console: 16 point font, 400 scans Console: colour VGA+ 80x25, 1 virtual console (max 63) pcibios_init : BIOS32 Service Directory Structure at 0x000ffee0 pcibios_init : BIOS32 Service Directory entry at 0xf0000

  Read the article

• How can I backup entire installations of a program, instead of just manually backing up individual f

  - by NoCatharsis

  It seems pretty straightforward to backup individual files, such as pictures, saved games, or settings files - just copy them straight over to your 2nd HDD or to an online service like DropBox. However, is there any way to backup entire installations of a program? For instance, my Firefox directory has a lot of personal customizations and add-ons. I don't want to go through each item and decide to back it up or let it go. So my next option is to copy out the entire directory for backup. But, if I copy the entire directory back onto the HD after a format, it is not an integrated installation and this seems like it could be troublesome. I would assume Windows cannot detect the directory for uninstallation, or would not let you choose Firefox as your default browser, right? I'm no pro, but this sounds like a bad idea. So my question is whether there is a good way to preserve all necessary files, while also preserving the full installation process of an application. This is not specific to Firefox - I would like to know how to do this for any application. Thank you.

  Read the article

• How do I fix error 1303 during TI Connect install?

  - by smoth190

  I recently purchased a TI-84 Plus graphing calculator, and I'm trying install the TI Connect software in order to connect the calculator to my computer via the USB cable. Unfortunately, I'm getting this error while trying to install the program: Error 1303. The installation has insufficient privileges to access this directory: E:\Data\Timothy\Documents\MyTIData. The installation cannot continue. Log on as administrator or contact your system administrator. However, my account is the only account on my PC, and it has administrative privileges. I've also tried running the installer with Run as Administrator, but with no luck. If I create the folder MyTIData manually, I receive this error: Error 1317. An error occurred while attempting to create the directory: E:\Data\Timothy\Documents\MyTIData I've reapplied the security settings to the E:\Data folder (and all its sub-directories) to Full for my account. I've also gone into Computer Management, and given SYSTEM full privileges for the entire disk. I've also logged out, logged back in, restarted, etc. but still, no luck. Now, I should mention that my Documents folder is not at the default location. I changed it due to my C: disk being a 90GB SSD, so I moved all my personal data onto the extra storage disk (which is ~1TB). I don't know if that is causing the issue, but it can't hurt throwing it out there. So why can't I install this program? Google'ing the problem brings up this error for various other installers (such as Visual Studio and Microsoft Office), but nothing for TI Connect. All the solutions are the same: Give the folder Full privileges...but I've already done this! I've also tried running the installer with and without the calculator plugged in, but it didn't change anything. In the prompt that contains the error, repeatedly clicking Retry or waiting a few moments before clicking Retry also produces no result.

  Read the article

• Windows 7 Install: No drives were found

  - by Albert Bori

  I was building a computer for my wife with an older SATA hard drive that I had lying around, and when attempting to do a new install of Windows 7 on it, the installer says: "No drives were found. Click Load Driver to provide a mass storage driver for installation." I ran the diskpart command: list volume, and it showed up as "Raw". So, I formatted it to NTFS and then it showed up as a healthy drive in diskpart. I also ran check disk on it with no errors. Windows 7 installer STILL can't find the drive. As far as BIOS settings, I have tried "Native IDE", AHCI, and Both AHCI/IDE mode (SATA slots 0-2 AHCI, 3-4 IDE). I tried all combinations... still "no drives were found". At this point, I'm just scratching my head. Using the installation dos window, I can see and talk to the drive just fine, but the installer just doesn't see it at all. I've even written folders and files to the drive, and it still "can't be seen". Any help would be great. Items of interest: Motherboard model: Gigabyte GA-A75M-UD2H - BIOS Version F5 (latest) Hard drive model: 80GB Seagate Barracuda 7200.7 ST380817AS (no other drives) Installing Windows 7 using a FAT32 formatted USB Drive, which I've used for other installs

  Read the article

• Problem with ubuntu 10.10 running from USB drive

  - by Surjya Narayana Padhi

  I recently downloaded Ubuntu 10.10 and created an USB drive with that. I started to run the Ubuntu from that USB drive. But I am facing so much problem. I am thinking why its not so much easy like Windows to do all my job in ubuntu. Always I get some error message or to install something. This time I am getting the following errors. I am trying to download and install Aircrack-ng. So used the command sudo apt-get install aircrack-ng. But the installation stops with the following error : update-initramfs: deferring update (trigger activated) cp: cannot stat `/vmlinuz': No such file or directory dpkg: error processing bcmwl-kernel-source (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: initramfs-tools bcmwl-kernel-source E: Sub-process /usr/bin/dpkg returned an error code (1) I don't even have the aptitude command installed till now. Are all these errors because of I am running the ubuntu from USB drive? Is there any simple and easy way to go to Ubuntu Software Center and download all the required essentials at one shot and then Aircrack-ng? I could not find the Aircrack-ng in Ubuntu Software Center Can anybody give me detail steps to solve all my problems above. I am frustrated searching for updates and installations. When something works and something does not work. Can anybody suggest me how I should proceed after installing ubuntu to run on a USB drive. So that I can use the OS like Windows. Like software download,wireless driver, sound, video, documents, C:, D: all things should be there. Please somebody help.

  Read the article

• My yum repository able to search packages, but not able to install it in RHEL?

  - by mandy

  I set up yum from dvd. Following is the containts of my .repo file: [dvd] name=Red Hat Enterprise Linux Installation DVD baseurl=file:///media/dvd enabled=0. I'm able to search packages. However while installation I'm getting below error: [root@localhost dvd]# yum install libstdc++.x86_64 Loaded plugins: rhnplugin, security This system is not registered with RHN. RHN support will be disabled. Setting up Install Process Nothing to do My Yum Search output: [root@localhost dvd]# yum search gcc Loaded plugins: rhnplugin, security This system is not registered with RHN. RHN support will be disabled. ============================================================================= Matched: gcc ============================================================================= compat-libgcc-296.i386 : Compatibility 2.96-RH libgcc library compat-libstdc++-296.i386 : Compatibility 2.96-RH standard C++ libraries compat-libstdc++-33.i386 : Compatibility standard C++ libraries compat-libstdc++-33.x86_64 : Compatibility standard C++ libraries cpp.x86_64 : The C Preprocessor. libgcc.i386 : GCC version 4.1 shared support library libgcc.x86_64 : GCC version 4.1 shared support library libgcj.i386 : Java runtime library for gcc libgcj.x86_64 : Java runtime library for gcc libstdc++.i386 : GNU Standard C++ Library libstdc++.x86_64 : GNU Standard C++ Library libtermcap.i386 : A basic system library for accessing the termcap database. libtermcap.x86_64 : A basic system library for accessing the termcap database. Please guide me on this, I want to install gcc on my RHEL.

  Read the article

• Problem with ubuntu 10.10 running from USB drive

  - by Surjya Narayana Padhi

  Hi Geeks, I recently downloaded Ubuntu 10.10 and created an USB drive with that. I started to run the Ubuntu from that USB drive. But I am facing so much problem. I am thinking why its not so much easy like Windows to do all my job in ubuntu. Always I get some error message or to install something. This time I am getting the following errors. I am trying to download and install Aircrack-ng. So used the command sudo apt-get install aircrack-ng. But the installation stops with the following error : update-initramfs: deferring update (trigger activated) cp: cannot stat `/vmlinuz': No such file or directory dpkg: error processing bcmwl-kernel-source (--configure): subprocess installed post-installation script returned error exit status 1 Errors were encountered while processing: initramfs-tools bcmwl-kernel-source E: Sub-process /usr/bin/dpkg returned an error code (1) I don't even have the aptitude command installed till now. Are all these errors because of I am running the ubuntu from USB drive? Is there any simple and easy way to go to Ubuntu Software Center and download all the required essentials at one shot and then Aircrack-ng? I could not find the Aircrack-ng in Ubuntu Software Center Can anybody give me detail steps to solve all my problems above. I am frustrated searching for updates and installations. When something works and something does not work. Can anybody suggest me how I should proceed after installing ubuntu to run on a USB drive. So that I can use the OS like Windows. Like software download,wireless driver, sound, video, documents, C:, D: all things should be there. Please somebody help.

  Read the article

• Troubles Installing Windows 7 via USB. Flat install?

  - by Brian

  Hi friends, I've been struggling with this for a while. Windows 7 64-bit Enterprise edition just will not install on my Shuttle K45 system via a USB key. It hangs out during the install while copying files or while creating the partitions. The system is pretty standard and low-tech: IDE hard drives, no CD, 2G RAM. I am not sure what of the problem. Other than the Shuttle, I have a Apple MacBook Pro. On the MPB, I am running OS X, and Mint Linux and Window XP over Parallels. I have an ISO of Win7 that works (I installed it as a Parallels VM to make sure). I have used UltraISO and MS Windows 7 USB/DVD Download Tool to write it to the 8G USB key. Both seem to copy all the files correctly (with UltraISO, I asked it to verify). It boots via USB and the install looks just fine. Until it hangs, most of the time with a copying error of 0x80070241. So now I am trying to figure out if there are other ways I can install Windows 7 on this Shuttle system that has no CD drive. I've heard about a flat installation, however those all seem to be doing something from within Windows. I do have access to a command prompt from the Windows 7 install. Does anyone know if/how I can prep the Shuttle hard drive with Windows 7 installation and have Windows 7 install from the hard disk. I do not have an external enclosure for the IDE HD and I do not have any other system I can hook up to the hard drives. I do have an external Maxtor OneTouch drive available.

  Read the article

• Cannot install windows. Compaq Presario CQ62

  - by Matthew

  I bought a used Compaq Presario CQ62 for cheap, and went to install windows on it. I formatted the partition and went to install when I got this error.... Windows cannot install required files. The file may be corrupt or missing. Make sure all files required for installation are available and restart the installation. Error code: 0x80070017 I have used this disk before with no problems, but internet searching suggested I burn one at 2x speed because that helps for some reason... I'm burning one now, but my question is, why would I get this error, OTHER than the disc being bad? I'm pretty certain this one isn't as I have used it before... (ok so the slowly burned cd (using imgburn) didn't work either so it's DEFINITELY not the disc) Thanks in advanced for any answers Also I took one stick of ram out because internet searching also suggested that, but it didn't make a difference. Also I ran memory and hard drive checks and they passed fine. Also I reset the motherboard options to default What could it be!? Help I'm completely stumped...

  Read the article

• Unable to install Management Studio Express 2008 due to Visual Studio 2008 installation

  - by Jamie

  I am attempting to install Managment Studio Express 2008 on a Win7 system that already has Visual Studio 2008 installed. I have installed VS 2008 SP1, which results in the About box for Visual Studio giving a version of 9.0.30792.1 SP. When I attempt the Management Studio installation I see a message that tells me that I must install SP1. However, this is already installed. After a fair bit of searching I came across the link below, where someone had commented with a command line option for the installation executable that forced it to skip the check. However, this simply pushed the error to later in the installation process. http://www.thushanfernando.com/index.php/2008/08/10/fix-rule-previous-releases-of-microsoft-visual-studio-2008-failed/. This seems to be a perennial problem for Microsoft. I can't remember a time when I've painlessly installed both Management Studio and Visual Studio. I can't imagine that this is an unusual combination, after all! Anyone had any success in solving this problem before I take on the day-long task of uninstalling and reinstalling Visual Studio and all its associated bits?

  Read the article

• Javassist failure in hibernate: invalid constant type: 60

  - by Kaleb Pederson

  I'm creating a cli tool to manage an existing application. Both the application and the tests build fine and run fine but despite that I receive a javassist failure when running my cli tool that exists within the jar: INFO: Bytecode provider name : javassist ... INFO: Hibernate EntityManager 3.5.1-Final Exception in thread "main" javax.persistence.PersistenceException: Unable to configure EntityManagerFactory at org.hibernate.ejb.Ejb3Configuration.configure(Ejb3Configuration.java:371) at org.hibernate.ejb.HibernatePersistence.createEntityManagerFactory(HibernatePersistence.java:55) at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java:48) at javax.persistence.Persistence.createEntityManagerFactory(Persistence.java:32) ... at com.sophware.flexipol.admin.AdminTool.<init>(AdminTool.java:40) at com.sophware.flexipol.admin.AdminTool.main(AdminTool.java:69) Caused by: java.lang.RuntimeException: Error while reading file:flexipol-jar-with-dependencies.jar at org.hibernate.ejb.packaging.NativeScanner.getClassesInJar(NativeScanner.java:131) at org.hibernate.ejb.Ejb3Configuration.addScannedEntries(Ejb3Configuration.java:467) at org.hibernate.ejb.Ejb3Configuration.addMetadataFromScan(Ejb3Configuration.java:457) at org.hibernate.ejb.Ejb3Configuration.configure(Ejb3Configuration.java:347) ... 11 more Caused by: java.io.IOException: invalid constant type: 60 at javassist.bytecode.ConstPool.readOne(ConstPool.java:1027) at javassist.bytecode.ConstPool.read(ConstPool.java:970) at javassist.bytecode.ConstPool.<init>(ConstPool.java:127) at javassist.bytecode.ClassFile.read(ClassFile.java:693) at javassist.bytecode.ClassFile.<init>(ClassFile.java:85) at org.hibernate.ejb.packaging.AbstractJarVisitor.checkAnnotationMatching(AbstractJarVisitor.java:243) at org.hibernate.ejb.packaging.AbstractJarVisitor.executeJavaElementFilter(AbstractJarVisitor.java:209) at org.hibernate.ejb.packaging.AbstractJarVisitor.addElement(AbstractJarVisitor.java:170) at org.hibernate.ejb.packaging.FileZippedJarVisitor.doProcessElements(FileZippedJarVisitor.java:119) at org.hibernate.ejb.packaging.AbstractJarVisitor.getMatchingEntries(AbstractJarVisitor.java:146) at org.hibernate.ejb.packaging.NativeScanner.getClassesInJar(NativeScanner.java:128) ... 14 more Since I know the jar is fine as the unit and integration tests run against it, I thought it might be a problem with javassist, so I tried cglib. The bytecode provider then shows as cglib but I still get the exact same stack trace with javassist present in it. cglib is definitely in the classpath: $ unzip -l flexipol-jar-with-dependencies.jar | grep cglib | wc -l 383 I've tried with both hibernate 3.4 and 3.5 and get the exact same error. Is this a problem with javassist?

  Read the article

• Debugging MinGW program with gdb on Windows, not terminating at assert failure

  - by devil

  How do I set up gdb on window so that it does not allow a program with assertion failure to terminate? I intend to check the stack trace and variables in the program. For example, running this test.cpp program compiled with MinGW 'g++ -g test.cpp -o test' in gdb: #include <cassert> int main(int argc, char ** argv) { assert(1==2); return 0; } Gives: $ gdb test.exe GNU gdb 6.8 Copyright (C) 2008 Free Software Foundation, Inc. License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html> This is free software: you are free to change and redistribute it. There is NO WARRANTY, to the extent permitted by law. Type "show copying" and "show warranty" for details. This GDB was configured as "i686-pc-mingw32"... (gdb) r Starting program: f:\code/test.exe [New thread 4616.0x1200] Error: dll starting at 0x77030000 not found. Error: dll starting at 0x75f80000 not found. Error: dll starting at 0x77030000 not found. Error: dll starting at 0x76f30000 not found. Assertion failed: 1==2, file test.cpp, line 2 This application has requested the Runtime to terminate it in an unusual way. Please contact the application's support team for more information. Program exited with code 03. (gdb) I would like to be able to stop the program from terminating immediately, like how Visual Studio's debugger and gdb on Linux does it. I have done a search and found some stuff on trapping signals but I can't seem to find a good post on how to set up gdb to do this.

  Read the article

• SSIS: "Failure inserting into the read-only column <ColumnName>"

  - by Cory

  I have an Excel source going into an OLE DB destination. I'm inserting data into a view that has an INSTEAD OF trigger that handles all inserts. When I try to execute the package I receive this error: "Failure inserting into the read-only column ColumnName" What can I do to let SSIS know that this view is safe to insert into because there is an INSTEAD OF trigger that will handle the insert? EDIT (Additional info): Some more additional info. I have a flat file that is being inserted into a normalized database. My initial problem was how do I take a flat file and insert that data into multiple tables while keeping track of all the primary/foreign key relationships. My solution was to create a VIEW that mimicked the structure of the flat file and then create an INSTEAD OF trigger on that view. In my INSTEAD OF trigger I would handle the logic of maintaining all the relationships between tables My view looks something like this. CREATE VIEW ImportView AS SELECT CONVERT(varchar(100, NULL) AS CustomerName, CONVERT(varchar(100), NULL) AS Address1, CONVERT(varchar(100), NULL) AS Address2, CONVERT(varchar(100), NULL) AS City, CONVERT(char(2), NULL) AS State, CONVERT(varchar(250), NULL) AS ItemOrdered, CONVERT(int, NULL) AS QuantityOrdered ... I will never need to select from this view, I only use it to insert data into it from this flat file I receive. I need someway to tell SQL Server that the fields aren't really read only because there is an INSTEAD OF trigger on this view.

  Read the article

< Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >