Search Results

Search found 150 results on 6 pages for 'slowness'.

Page 1/6 | 1 2 3 4 5 6  | Next Page >

• Slowness on Exchange 2007 Server (network related we think)

  - by Az

  We are seeing some odd behavior out of our exchange 2007 server. I believe it is network related as during the slowness in response from the exchange server. During these times downloading files to server is fraught with connection resets and extreme slow download speeds that are not affecting other servers right on the same subnet with the same gateway and ISP. We have about 50 users at a time using Outlook 2003 from a terminal server not displaying any other signs of slowness, all network slowness is confirmed trying downloads on the exchange server itself. Checked for virus issues, there are none. Checked for hardware issues, none found I am noticing between 200-400 TCPv4 connections established I am seeing around 100k tcpv4(active) connections according to perfmon are these numbers odd? Has anyone run into anything similar? Our server has a gigbabit NIC linked to a gigabit switch using cat6 so I do not believe it is "physical". Thanks!

  Read the article

• Realtime website slowness (PHP/MYSQL)

  - by 3s2ng

  We got a website with realtime transactions. The past few days we experienced some slowness during a period of time. Usually the slowness last for 5 minutes. And also during the slowness we noticed that sometimes we can not connect to SSH and FTP or sometimes very slow to connect to those services. Currently we are trying to identify the issue. We already setup database monitoring tool. Now are about to signup with pingdom.com My question is. If the website is too slow due to the database (table or row lock) will it affect the other services like SSH and FTP? Does the ping correlates the page load and the connection between my PC and server? Thanks, Mark

  Read the article

• MacBook Pro Late 2009 SATA Resets, Slowness

  - by A Student at a University

  My MacBook Pro runs slower the longer it's on. I am getting kernel warnings. The resets correlate with AC power connects and disconnects. I don't know if the warnings do. (How do I tell?) Are these bus CRC errors? Or something else? Can this damage the drive or corrupt data? What is it seeing that motivates these? 02:37:16 :[ 0.791992] ahci 0000:00:0b.0: PCI INT A -> Link[LSI0] -> GSI 20 (level, low) -> IRQ 20 02:37:16 :[ 0.792053] ahci 0000:00:0b.0: controller can't do PMP, turning off CAP_PMP 02:37:16 :[ 0.792104] ahci 0000:00:0b.0: AHCI 0001.0200 32 slots 6 ports 1.5 Gbps 0x3 impl IDE mode 02:37:16 :[ 0.792107] ahci 0000:00:0b.0: flags: 64bit ncq sntf pm led pio slum part boh 02:37:16 :[ 0.813473] scsi0 : ahci 02:37:16 :[ 0.823340] scsi1 : ahci 02:37:16 :[ 0.848164] ata1: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484100 irq 43 02:37:16 :[ 0.848166] ata2: SATA max UDMA/133 abar m8192@0xe7484000 port 0xe7484180 irq 43 02:37:16 :[ 1.190132] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.190153] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.213568] ata1.00: ATA-8: OCZ-VERTEX2, 1.23, max UDMA/133 02:37:16 :[ 1.213572] ata1.00: 195371568 sectors, multi 1: LBA48 NCQ (depth 31/32) 02:37:16 :[ 1.227293] ata2.00: ATA-8: ST9500420ASG, 0002SDM1, max UDMA/133 02:37:16 :[ 1.227297] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) 02:37:16 :[ 1.229570] ata2.00: configured for UDMA/133 02:37:16 :[ 1.240133] ata2: hard resetting link 02:37:16 :[ 1.260738] ata1.00: configured for UDMA/133 02:37:16 :[ 1.280122] ata1: hard resetting link 02:37:16 :[ 1.470125] usb 2-5: new high speed USB device using ehci_hcd and address 3 02:37:16 :[ 1.550165] firewire_core: created device fw0: GUID 58b035fffea99f5c, S800 02:37:16 :[ 1.631306] Initializing USB Mass Storage driver... 02:37:16 :[ 1.631392] scsi6 : usb-storage 2-5:1.0 02:37:16 :[ 1.631454] usbcore: registered new interface driver usb-storage 02:37:16 :[ 1.631455] USB Mass Storage support registered. 02:37:16 :[ 1.960128] usb 4-1: new full speed USB device using ohci_hcd and address 2 02:37:16 :[ 1.990101] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 1.994215] ata2.00: configured for UDMA/133 02:37:16 :[ 1.994220] ata2: EH complete 02:37:16 :[ 2.030097] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:16 :[ 2.090773] ata1.00: configured for UDMA/133 02:37:16 :[ 2.090778] ata1: EH complete 02:37:16 :[ 2.090931] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX2 1.23 PQ: 0 ANSI: 5 02:37:16 :[ 2.091045] sd 0:0:0:0: Attached scsi generic sg0 type 0 02:37:16 :[ 2.091121] sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB) 02:37:16 :[ 2.091159] scsi 1:0:0:0: Direct-Access ATA ST9500420ASG 0002 PQ: 0 ANSI: 5 02:37:16 :[ 2.091163] sd 0:0:0:0: [sda] Write Protect is off 02:37:16 :[ 2.091183] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16 :[ 2.091252] sd 1:0:0:0: Attached scsi generic sg1 type 0 02:37:16 :[ 2.091337] sda: 02:37:16 :[ 2.091446] sd 1:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) 02:37:16 :[ 2.091580] sd 1:0:0:0: [sdb] Write Protect is off 02:37:16 :[ 2.091637] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 02:37:16 :[ 2.091756] sdb: sda1 sda2 02:37:16 :[ 2.093140] sd 0:0:0:0: [sda] Attached SCSI disk 02:37:16 :[ 2.093505] sdb1 sdb2 sdb3 02:37:16 :[ 2.093773] sd 1:0:0:0: [sdb] Attached SCSI disk 02:37:16 :[ 2.693899] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) 02:37:16 :[ 5.483492] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro 02:37:16 :[ 7.905040] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null) 02:37:25 :[ 19.553095] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:25 :[ 19.555266] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:25 :[ 19.641533] ata1: hard resetting link 02:37:25 :[ 19.642084] ata2: hard resetting link 02:37:26 :[ 20.392606] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26 :[ 20.392610] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:26 :[ 20.396697] ata2.00: configured for UDMA/133 02:37:26 :[ 20.396703] ata2: EH complete 02:37:26 :[ 20.451491] ata1.00: configured for UDMA/133 02:37:26 :[ 20.451498] ata1: EH complete 02:37:30 :[ 24.563725] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:37:30 :[ 24.565939] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:37:30 :[ 24.627246] ata1: hard resetting link 02:37:30 :[ 24.632250] ata2: hard resetting link 02:37:31 :[ 25.372582] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31 :[ 25.382615] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) 02:37:31 :[ 25.386782] ata2.00: configured for UDMA/133 02:37:31 :[ 25.386788] ata2: EH complete 02:37:31 :[ 25.431668] ata1.00: configured for UDMA/133 02:37:31 :[ 25.431674] ata1: EH complete 02:45:54 :[ 529.141844] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:55 :[ 529.544529] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:55 :[ 529.622561] ata1: limiting SATA link speed to 1.5 Gbps 02:45:55 :[ 529.622583] ata1: hard resetting link 02:45:55 :[ 529.622609] ata2: limiting SATA link speed to 1.5 Gbps 02:45:55 :[ 529.622624] ata2: hard resetting link 02:45:56 :[ 530.380135] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56 :[ 530.380157] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:56 :[ 530.384305] ata2.00: configured for UDMA/133 02:45:56 :[ 530.384314] ata2: EH complete 02:45:56 :[ 530.399225] ata1.00: configured for UDMA/133 02:45:56 :[ 530.399233] ata1: EH complete 02:45:58 :[ 532.395990] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:45:58 :[ 532.518270] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:45:58 :[ 532.590983] ata1: hard resetting link 02:45:58 :[ 532.591045] ata2: hard resetting link 02:45:59 :[ 533.340147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59 :[ 533.340168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:45:59 :[ 533.344416] ata2.00: configured for UDMA/133 02:45:59 :[ 533.344424] ata2: EH complete 02:45:59 :[ 533.360839] ata1.00: configured for UDMA/133 02:45:59 :[ 533.360847] ata1: EH complete 02:45:59 :[ 533.584449] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:45:59 :[ 533.586999] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:45:59 :[ 533.660132] ata2: hard resetting link 02:45:59 :[ 533.660151] ata1: hard resetting link 02:46:00 :[ 534.412536] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00 :[ 534.412562] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:00 :[ 534.416768] ata2.00: configured for UDMA/133 02:46:00 :[ 534.416777] ata2: EH complete 02:46:00 :[ 534.431396] ata1.00: configured for UDMA/133 02:46:00 :[ 534.431401] ata1: EH complete 02:46:03 :[ 537.384649] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:03 :[ 537.504214] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:03 :[ 537.586002] ata1: hard resetting link 02:46:03 :[ 537.586036] ata2: hard resetting link 02:46:04 :[ 538.330147] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04 :[ 538.330168] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:04 :[ 538.334389] ata2.00: configured for UDMA/133 02:46:04 :[ 538.334398] ata2: EH complete 02:46:04 :[ 538.343511] ata1.00: configured for UDMA/133 02:46:04 :[ 538.343519] ata1: EH complete 02:46:04 :[ 538.456413] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:04 :[ 538.459404] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:04 :[ 538.540138] ata1.00: limiting speed to UDMA/100:PIO4 02:46:04 :[ 538.540159] ata1: hard resetting link 02:46:04 :[ 538.540202] ata2.00: limiting speed to UDMA/100:PIO4 02:46:04 :[ 538.540220] ata2: hard resetting link 02:46:05 :[ 539.290054] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05 :[ 539.290041] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:05 :[ 539.294100] ata2.00: configured for UDMA/100 02:46:05 :[ 539.294106] ata2: EH complete 02:46:05 :[ 539.314125] ata1.00: configured for UDMA/100 02:46:05 :[ 539.314132] ------------[ cut here ]------------ 02:46:05 :[ 539.314140] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:05 :[ 539.314144] Hardware name: MacBookPro5,3 02:46:05 :[ 539.314146] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:05 :[ 539.314221] Pid: 202, comm: scsi_eh_0 Tainted: P 2.6.35-25-generic #44-Ubuntu 02:46:05 :[ 539.314224] Call Trace: 02:46:05 :[ 539.314233] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:05 :[ 539.314237] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:05 :[ 539.314242] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:05 :[ 539.314246] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:05 :[ 539.314256] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:05 :[ 539.314261] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:05 :[ 539.314266] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:05 :[ 539.314270] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:05 :[ 539.314275] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:05 :[ 539.314280] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:05 :[ 539.314284] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:05 :[ 539.314288] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:05 :[ 539.314291] ---[ end trace 76dbffc2d5d49d9b ]--- 02:46:05 :[ 539.314296] ata1: EH complete 02:46:12 :[ 547.040117] ata1: hard resetting link 02:46:13 :[ 547.390144] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:13 :[ 547.408430] ata1.00: configured for UDMA/100 02:46:13 :[ 547.408438] ------------[ cut here ]------------ 02:46:13 :[ 547.408447] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 02:46:13 :[ 547.408451] Hardware name: MacBookPro5,3 02:46:13 :[ 547.408453] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 02:46:13 :[ 547.408528] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 02:46:13 :[ 547.408531] Call Trace: 02:46:13 :[ 547.408540] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 02:46:13 :[ 547.408544] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 02:46:13 :[ 547.408549] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 02:46:13 :[ 547.408553] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 02:46:13 :[ 547.408563] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 02:46:13 :[ 547.408567] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 02:46:13 :[ 547.408572] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 02:46:13 :[ 547.408577] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 02:46:13 :[ 547.408582] [<ffffffff8107f266>] kthread+0x96/0xa0 02:46:13 :[ 547.408587] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 02:46:13 :[ 547.408591] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 02:46:13 :[ 547.408595] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 02:46:13 :[ 547.408598] ---[ end trace 76dbffc2d5d49d9c ]--- 02:46:13 :[ 547.408620] ata1: EH complete 02:46:13 :[ 547.562470] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:13 :[ 547.671380] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:13 :[ 547.738198] ata1.00: limiting speed to UDMA/33:PIO4 02:46:13 :[ 547.738218] ata1: hard resetting link 02:46:13 :[ 547.738274] ata2: hard resetting link 02:46:14 :[ 548.482561] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14 :[ 548.484083] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:14 :[ 548.486809] ata2.00: configured for UDMA/100 02:46:14 :[ 548.486818] ata2: EH complete 02:46:14 :[ 548.498998] ata1.00: configured for UDMA/33 02:46:14 :[ 548.499004] ata1: EH complete 02:46:18 :[ 552.410499] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:18 :[ 552.522521] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:18 :[ 552.529684] ata1: hard resetting link 02:46:18 :[ 552.529723] ata2: hard resetting link 02:46:19 :[ 553.280059] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19 :[ 553.280068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:19 :[ 553.284141] ata2.00: configured for UDMA/100 02:46:19 :[ 553.284150] ata2: EH complete 02:46:19 :[ 553.301629] ata1.00: configured for UDMA/33 02:46:19 :[ 553.301637] ata1: EH complete 02:46:21 :[ 556.078830] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:21 :[ 556.180361] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:22 :[ 556.262612] ata1: hard resetting link 02:46:22 :[ 556.262617] ata2: hard resetting link 02:46:22 :[ 557.010050] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:22 :[ 557.010070] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:22 :[ 557.014069] ata2.00: configured for UDMA/100 02:46:22 :[ 557.014075] ata2: EH complete 02:46:22 :[ 557.023646] ata1.00: configured for UDMA/33 02:46:22 :[ 557.023654] ata1: EH complete 02:46:30 :[ 565.047438] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:46:30 :[ 565.051554] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:46:30 :[ 565.108332] ata1: hard resetting link 02:46:30 :[ 565.108389] ata2.00: limiting speed to UDMA/33:PIO4 02:46:30 :[ 565.108406] ata2: hard resetting link 02:46:31 :[ 565.850048] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:31 :[ 565.850068] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:31 :[ 565.854304] ata2.00: configured for UDMA/33 02:46:31 :[ 565.854313] ata2: EH complete 02:46:31 :[ 565.868477] ata1.00: configured for UDMA/33 02:46:31 :[ 565.868485] ata1: EH complete 02:46:35 :[ 569.265469] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 02:46:35 :[ 569.268139] EXT4-fs (dm-2): re-mounted. Opts: commit=0 02:46:35 :[ 569.340079] ata1: hard resetting link 02:46:35 :[ 569.340113] ata2: hard resetting link 02:46:35 :[ 570.092568] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:35 :[ 570.092589] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:46:35 :[ 570.096828] ata2.00: configured for UDMA/33 02:46:35 :[ 570.096837] ata2: EH complete 02:46:35 :[ 570.110727] ata1.00: configured for UDMA/33 02:46:35 :[ 570.110735] ata1: EH complete 02:47:04 :[ 598.528232] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 02:47:04 :[ 598.653973] EXT4-fs (dm-2): re-mounted. Opts: commit=600 02:47:04 :[ 598.730854] ata1: hard resetting link 02:47:04 :[ 598.730910] ata2: hard resetting link 02:47:05 :[ 599.480136] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:47:05 :[ 599.480159] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 02:47:05 :[ 599.484206] ata2.00: configured for UDMA/33 02:47:05 :[ 599.484213] ata2: EH complete 02:47:05 :[ 599.496699] ata1.00: configured for UDMA/33 02:47:05 :[ 599.496707] ata1: EH complete 04:45:59 :[ 7733.756548] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 04:45:59 :[ 7733.882748] EXT4-fs (dm-2): re-mounted. Opts: commit=0 04:45:59 :[ 7733.960142] ata1: hard resetting link 04:45:59 :[ 7733.960189] ata2: hard resetting link 04:46:00 :[ 7734.701926] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 04:46:00 :[ 7734.719939] ata1.00: configured for UDMA/33 04:46:00 :[ 7734.719946] ata1: EH complete 04:46:00 :[ 7734.722547] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 04:46:00 :[ 7734.726652] ata2.00: configured for UDMA/33 04:46:00 :[ 7734.726659] ata2: EH complete 04:46:02 :[ 7736.656465] ACPI: EC: GPE storm detected, transactions will use polling mode 13:38:49 :[39704.188621] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 13:38:49 :[39704.280588] EXT4-fs (dm-2): re-mounted. Opts: commit=600 13:38:49 :[39704.360819] ata1: hard resetting link 13:38:49 :[39704.360882] ata2: hard resetting link 13:38:50 :[39705.112956] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 13:38:50 :[39705.114435] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 13:38:50 :[39705.118673] ata2.00: configured for UDMA/33 13:38:50 :[39705.118682] ata2: EH complete 13:38:50 :[39705.127076] ata1.00: configured for UDMA/33 13:38:50 :[39705.127084] ata1: EH complete 13:39:49 :[39764.142463] applesmc: F1Mn: write arg fail 13:48:11 :[40267.025145] applesmc: FS! : read arg fail 13:52:53 :[40548.596735] applesmc: FS! : read arg fail 13:53:58 :[40613.972856] applesmc: FS! : read arg fail 13:54:08 :[40624.057339] applesmc: FS! : read arg fail 13:58:20 :[40875.397749] applesmc: TC0D: read data fail 14:16:56 :[41991.722054] applesmc: Th2H: read data fail 14:22:32 :[42327.991522] applesmc: light sensor data length set to 10 14:26:19 :[42554.788886] applesmc: F1Mn: write arg fail 14:32:36 :[42931.860443] applesmc: TC0F: read data fail 14:34:32 :[43048.041469] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 14:34:33 :[43048.185850] EXT4-fs (dm-2): re-mounted. Opts: commit=0 14:34:33 :[43048.270184] ata1: hard resetting link 14:34:33 :[43048.270224] ata2: hard resetting link 14:34:33 :[43049.030049] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:33 :[43049.030065] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:33 :[43049.034106] ata2.00: configured for UDMA/33 14:34:33 :[43049.034112] ata2: EH complete 14:34:33 :[43049.056952] ata1.00: configured for UDMA/33 14:34:33 :[43049.056959] ------------[ cut here ]------------ 14:34:33 :[43049.056968] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 14:34:33 :[43049.056971] Hardware name: MacBookPro5,3 14:34:33 :[43049.056973] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 14:34:33 :[43049.057048] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 14:34:33 :[43049.057052] Call Trace: 14:34:33 :[43049.057060] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 14:34:33 :[43049.057064] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 14:34:33 :[43049.057069] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 14:34:33 :[43049.057074] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 14:34:33 :[43049.057083] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 14:34:33 :[43049.057088] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 14:34:33 :[43049.057093] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 14:34:33 :[43049.057097] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 14:34:33 :[43049.057102] [<ffffffff8107f266>] kthread+0x96/0xa0 14:34:33 :[43049.057107] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 14:34:33 :[43049.057111] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 14:34:33 :[43049.057115] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 14:34:33 :[43049.057118] ---[ end trace 76dbffc2d5d49d9d ]--- 14:34:33 :[43049.057123] ata1: EH complete 14:34:41 :[43057.012698] ata1: hard resetting link 14:34:42 :[43057.362780] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:42 :[43057.381432] ata1.00: configured for UDMA/33 14:34:42 :[43057.381441] ------------[ cut here ]------------ 14:34:42 :[43057.381450] WARNING: at /build/buildd/linux-2.6.35/drivers/ata/libata-eh.c:3638 ata_eh_finish+0xdf/0xf0() 14:34:42 :[43057.381453] Hardware name: MacBookPro5,3 14:34:42 :[43057.381455] Modules linked in: michael_mic arc4 xt_multiport binfmt_misc rfcomm sco bnep l2cap parport_pc ppdev nvidia(P) ipt_REJECT xt_recent snd_hda_codec_cirrus xt_limit xt_tcpudp ipt_addrtype xt_state snd_hda_intel snd_hda_codec snd_hwdep snd_pcm snd_seq_midi applesmc led_class ip6table_filter lib80211_crypt_tkip snd_rawmidi snd_seq_midi_event ip6_tables input_polldev hid_apple snd_seq wl(P) snd_timer snd_seq_device snd joydev bcm5974 usbhid mbp_nvidia_bl uvcvideo btusb videodev v4l1_compat v4l2_compat_ioctl32 nf_nat_irc hid nf_conntrack_irc soundcore snd_page_alloc i2c_nforce2 coretemp lib80211 bluetooth nf_nat_ftp nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack_ftp nf_conntrack lp parport iptable_filter ip_tables x_tables usb_storage firewire_ohci firewire_core forcedeth crc_itu_t ahci libahci 14:34:42 :[43057.381530] Pid: 202, comm: scsi_eh_0 Tainted: P W 2.6.35-25-generic #44-Ubuntu 14:34:42 :[43057.381533] Call Trace: 14:34:42 :[43057.381542] [<ffffffff8106091f>] warn_slowpath_common+0x7f/0xc0 14:34:42 :[43057.381546] [<ffffffff8106097a>] warn_slowpath_null+0x1a/0x20 14:34:42 :[43057.381551] [<ffffffff813dc77f>] ata_eh_finish+0xdf/0xf0 14:34:42 :[43057.381556] [<ffffffff813e441e>] sata_pmp_error_handler+0x2e/0x40 14:34:42 :[43057.381565] [<ffffffffa00021bf>] ahci_error_handler+0x1f/0x90 [libahci] 14:34:42 :[43057.381569] [<ffffffff813dd6d2>] ata_scsi_error+0x492/0x5e0 14:34:42 :[43057.381575] [<ffffffff813b24cd>] scsi_error_handler+0x10d/0x190 14:34:42 :[43057.381579] [<ffffffff813b23c0>] ? scsi_error_handler+0x0/0x190 14:34:42 :[43057.381584] [<ffffffff8107f266>] kthread+0x96/0xa0 14:34:42 :[43057.381589] [<ffffffff8100aee4>] kernel_thread_helper+0x4/0x10 14:34:42 :[43057.381594] [<ffffffff8107f1d0>] ? kthread+0x0/0xa0 14:34:42 :[43057.381598] [<ffffffff8100aee0>] ? kernel_thread_helper+0x0/0x10 14:34:42 :[43057.381601] ---[ end trace 76dbffc2d5d49d9e ]--- 14:34:42 :[43057.381624] ata1: EH complete 14:34:42 :[43057.557887] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 14:34:42 :[43057.560517] EXT4-fs (dm-2): re-mounted. Opts: commit=600 14:34:42 :[43057.621194] ata1: hard resetting link 14:34:42 :[43057.621252] ata2: hard resetting link 14:34:43 :[43058.370141] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:43 :[43058.370162] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:43 :[43058.374407] ata2.00: configured for UDMA/33 14:34:43 :[43058.374415] ata2: EH complete 14:34:43 :[43058.381989] ata1.00: configured for UDMA/33 14:34:43 :[43058.381996] ata1: EH complete 14:34:43 :[43058.616228] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=600 14:34:43 :[43058.618931] EXT4-fs (dm-2): re-mounted. Opts: commit=600 14:34:43 :[43058.626687] ata1: hard resetting link 14:34:43 :[43058.626731] ata2: hard resetting link 14:34:44 :[43059.372908] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:44 :[43059.372932] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 14:34:44 :[43059.376997] ata2.00: configured for UDMA/33 14:34:44 :[43059.377003] ata2: EH complete 14:34:44 :[43059.392576] ata1.00: configured for UDMA/33 14:34:44 :[43059.392585] ata1: EH complete 15:48:19 :[47474.710860] ata1: hard resetting link 15:48:19 :[47474.710882] ata2: hard resetting link 15:48:20 :[47475.460144] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 15:48:20 :[47475.460169] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 15:48:20 :[47475.473709] ata1.00: configured for UDMA/33 15:48:20 :[47475.473717] ata1: EH complete 15:48:20 :[47475.727960] ata2.00: configured for UDMA/33 15:48:20 :[47475.727969] ata2: EH complete 16:29:39 :[49954.295017] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro,commit=0 16:29:39 :[49954.622307] EXT4-fs (dm-2): re-mounted. Opts: commit=0 16:29:39 :[49954.710139] ata1: hard resetting link 16:29:39 :[49954.710174] ata2: hard resetting link 16:29:40 :[49955.460046] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 16:29:40 :[49955.460062] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) 16:29:40 :[49955.464138] ata2.00: configured for UDMA/33 16:29:40 :[49955.464144] ata2: EH complete 16:29:40 :[49955.473251] ata1.00: configured for UDMA/33 16:29:40 :[49955.473258] ata1: EH complete

  Read the article

• Dell OpenManage Causing Periodic Slowness

  - by Zorlack

  Today we diagnosed the cause of a Periodic slowness issue: see here. Dell OpenManage Server Administrator seems to have been causing hourly slowness. It would occasionally peg one of the CPUs for upwards of two minutes. Disabling it drastically improved the performance of the SQL Server. The server hardware: Dell R710 Dual Quad Core 2.9GHz Processors 96GB Memory 2 Disk RAID 1 SAS System Disk (Internal) 4 Disk RAID 10 SAS Log Disk (Internal) 14 Disk RAID 10 SAS Data Disk (External DAS MD1000) Windows 2008 Enterprise R2 x64 We installed the OS using Dell OpenManage Server Assistant, so I assume that it was correctly configured. For now we have disabled OMSA to alleviate the performance issues it was causing, but I'd like to be able to re-enable it. Has anyone had a similar experience that can shed a little light on the nature of this problem?

  Read the article

• Hourly SQL Server 2005 Slowness (Possibly caused by SYSTEM)

  - by Zorlack

  We're trying to diagnose the cause of slowness on our Database server. We're running the latest rev SQL Server 2005 on Windows 2008x64. The behavior that we're seeing is this: We see the SYSTEM process spike one of the CPUs for about 2 minutes, during this time SQL server slows down by a factor of 10. The slowness lasts until SYSTEM is done, then in an hour everything starts again. During these slowdowns disk writes don't spike, paging doesn't spike, the only noticeable precursor we see is that SYSTEM maxes out one of the sixteen (HT)CPUs. Note that this doesn't happen at the top of the hour, it just happens once an hour, and it shifts a bit depending on the length of the incident. At the moment this is causing intermittent slowdowns, but when the server is really busy it can cause Worker Thread starvation. The server is a Dual Quad Dell R710 with 96GB of RAM and RAID10 data/log disks. Has anyone experienced this kind of problem? Does anyone know where we should look?

  Read the article

• Hourly SQL Server 2005 Slowness (Possibly caused by SYSTEM)

  - by Zorlack

  We're trying to diagnose the cause of slowness on our Database server. We're running the latest rev SQL Server 2005 on Windows 2008x64. The behavior that we're seeing is this: We see the SYSTEM process spike one of the CPUs for about 2 minutes, during this time SQL server slows down by a factor of 10. The slowness lasts until SYSTEM is done, then in an hour everything starts again. During these slowdowns disk writes don't spike, paging doesn't spike, the only noticeable precursor we see is that SYSTEM maxes out one of the sixteen (HT)CPUs. Note that this doesn't happen at the top of the hour, it just happens once an hour, and it shifts a bit depending on the length of the incident. At the moment this is causing intermittent slowdowns, but when the server is really busy it can cause Worker Thread starvation. The server is a Dual Quad Dell R710 with 96GB of RAM and RAID10 data/log disks. Has anyone experienced this kind of problem? Does anyone know where we should look? Edit: SQL Server Version is 9.0.4035

  Read the article

• Windows Server 2012 R2 application installation slowness

  - by Eric

  Good afternoon, Windows Server 2012 R2 as host fully up to date Windows Server 2012 R2 as guest fully up to date Whether I am running it as a host or guest, whenever I am installing an application that should take a couple minutes it always ends up 3x-5x longer than it should. If I take the same applications and install it on any other OS (IE 2k8, 7,) it they install very quickly. Dell server management software took 30 minutes or so when it takes 5 minutes or so on 2k8. Even a clean install not joined to domain I still experience this same slowness on applications I attempt to install. So my question to everyone is, are you or anyone else experiencing this? I cannot find anything on google so this is why I am here

  Read the article

• extreme slowness with a remote database in Drupal

  - by ceejayoz

  We're attempting to scale our Drupal installations up and have decided on some dedicated MySQL boxes. Unfortunately, we're running into extreme slowness when we attempt to use the remote DB - page load times go from ~200 milliseconds to 5-10 seconds. Latency between the servers is minimal - a tenth or two of a millisecond. PING 10.37.66.175 (10.37.66.175) 56(84) bytes of data. 64 bytes from 10.37.66.175: icmp_seq=1 ttl=64 time=0.145 ms 64 bytes from 10.37.66.175: icmp_seq=2 ttl=64 time=0.157 ms 64 bytes from 10.37.66.175: icmp_seq=3 ttl=64 time=0.157 ms 64 bytes from 10.37.66.175: icmp_seq=4 ttl=64 time=0.144 ms 64 bytes from 10.37.66.175: icmp_seq=5 ttl=64 time=0.121 ms 64 bytes from 10.37.66.175: icmp_seq=6 ttl=64 time=0.122 ms 64 bytes from 10.37.66.175: icmp_seq=7 ttl=64 time=0.163 ms 64 bytes from 10.37.66.175: icmp_seq=8 ttl=64 time=0.115 ms 64 bytes from 10.37.66.175: icmp_seq=9 ttl=64 time=0.484 ms 64 bytes from 10.37.66.175: icmp_seq=10 ttl=64 time=0.156 ms --- 10.37.66.175 ping statistics --- 10 packets transmitted, 10 received, 0% packet loss, time 8998ms rtt min/avg/max/mdev = 0.115/0.176/0.484/0.104 ms Drupal's devel.module timers show the database queries aren't running any slower on the remote DB - about 150 microseconds whether it's the local or the remote server. Profiling with XHProf shows PHP execution times that aren't out of whack, either. Number of queries doesn't seem to make a difference - we seem the same 5-10 second delay whether a page has 12 queries or 250. Any suggestions about where I should start troubleshooting here? I'm quite confused.

  Read the article

• Windows 7 Slowness following Virtual PC and Visual Studio Install

  - by Elliot Hughes

  I'm running Windows 7 32bit on a 3.2ghz Pentium D with 2gb RAM and a 1TB SATA hard drive. My system was running as fast as it ever has until I installed Visual Studio and Virtual PC a few days ago. Ever since - regardless of whether either application has been running the system has been running incredibly slowly. For example flash video plays jumpily, 3D games that used to run fine are now unplayable and even the smallest amount of multitasking makes the system unusable. I'm confident there is no virus or other such things present following scans in safemode and I'm fairly confident I've made no other changes to my system. Any ideas - I've run out of things to try!

  Read the article

• Ubuntu 9.10 x86_32 with PAE causes graphics issues, mainly slowness

  - by widgisoft

  I've tried the 64bit version and found I was constantly hitting a brick wall trying to get 32bit stuff to run; I'd previously used PAE on 9.04 without any issues so figured I'd give it a shot. However, on 9.10 it seems PAE or the process of enabling PAE breaks the nvidia drivers/module somewhat as performance is terrible; I can't even enable desktop effects and there's lots of artifacting on random controls. Disabling the pae image and rebooting fixes the issue however I'm then stuck with "only" 2.7Gb of ram and unable to use the full 8gb that's installed. Is there somthing special I need to do when using pae and nVidia drivers or should I be using 64bit and just figure out how to force run 32bit packages? :-p

  Read the article

• Performance: Nginx SSL slowness or just SSL slowness in general?

  - by Mauvis Ledford

  I have an Amazon Web Services setup with an Apache instance behind Nginx with Nginx handling SSL and serving everything but the .php pages. In my ApacheBench tests I'm seeing this for my most expensive API call (which cache via Memcached): 100 concurrent calls to API call (http): 115ms (median) 260ms (max) 100 concurrent calls to API call (https): 6.1s (median) 11.9s (max) I've done a bit of research, disabled the most expensive SSL ciphers and enabled SSL caching (I know it doesn't help in this particular test.) Can you tell me why my SSL is taking so long? I've set up a massive EC2 server with 8CPUs and even applying consistent load to it only brings it up to 50% total CPU. I have 8 Nginx workers set and a bunch of Apache. Currently this whole setup is on one EC2 box but I plan to split it up and load balance it. There have been a few questions on this topic but none of those answers (disable expensive ciphers, cache ssl, seem to do anything.) Sample results below: $ ab -k -n 100 -c 100 https://URL This is ApacheBench, Version 2.3 <$Revision: 655654 $> Copyright 1996 Adam Twiss, Zeus Technology Ltd, http://www.zeustech.net/ Licensed to The Apache Software Foundation, http://www.apache.org/ Benchmarking URL.com (be patient).....done Server Software: nginx/1.0.15 Server Hostname: URL.com Server Port: 443 SSL/TLS Protocol: TLSv1/SSLv3,AES256-SHA,2048,256 Document Path: /PATH Document Length: 73142 bytes Concurrency Level: 100 Time taken for tests: 12.204 seconds Complete requests: 100 Failed requests: 0 Write errors: 0 Keep-Alive requests: 0 Total transferred: 7351097 bytes HTML transferred: 7314200 bytes Requests per second: 8.19 [#/sec] (mean) Time per request: 12203.589 [ms] (mean) Time per request: 122.036 [ms] (mean, across all concurrent requests) Transfer rate: 588.25 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 65 168 64.1 162 268 Processing: 385 6096 3438.6 6199 11928 Waiting: 379 6091 3438.5 6194 11923 Total: 449 6264 3476.4 6323 12196 Percentage of the requests served within a certain time (ms) 50% 6323 66% 8244 75% 9321 80% 9919 90% 11119 95% 11720 98% 12076 99% 12196 100% 12196 (longest request)

  Read the article

• Work around for yahoo mail slowness (using 100% cpu)

  - by Tony Lee

  My yahoo mail is very slow sometimes. When it is, I notice that IE8 is using 100% cpu. Using sysinternals process explorer I discovered the thread using all the cpu in IE8 has Flash in the stackwalk. I upgraded flash from 9 to 10, but the problem persists. I'm about to edit hosts to block the flash content by redirecting the yahoo and ad click dns entries. Is there some easier way to get flash to behave? The fix for the long run will be switching to gmail.

  Read the article

• Template loading slowness on VPN

  - by Mesut

  Hi All We have got lots of Word templates on our network. They are perfectly working on local area network. However, if users try to create a new word document from a template when they are connected to VPN outside of the office, it takes nearly 20 minutes to create a word file which is not reasonable at all. Have you guys ever come across with this type of issue? if yes, any suggestion or help would be appreciated. Many Thanks from now on. Best Regards Mesut

  Read the article

• Debugging SQL Server Slowness: Same Database, Different Servers

  - by Craig Walker

  For a while now we've been having anecdotal slowness on our newly-minted (VMWare-based) SQL Server 2005 database servers. Recently the problem has come to a head and I've started looking for the root cause of the issue. Here's the weird part: on the stored procedure that I'm using as a performance test case, I get a 30x difference in the execution speed depending on which DB server I run it on. This is using the same database (mdf) and log (ldf) files, detached, copied, and reattached from the slow server to the fast one. This doesn't appear to be a (virtualized) hardware issue: he slow server has 4x the CPU capacity and 2x the memory as the fast one. As best as I can tell, the problem lies in the environment/configuration of the servers (either operating system or SQL Server installation). However, I've checked a bunch of variables (SQL Server config options, running services, disk fragmentation) and found nothing that has made a difference in testing. What things should I be looking at? What tools can I use to investigate why this is happening?

  Read the article

• BackupExec 12 + RALUS - VERY slow backups

  - by LVDave

  We use Backup Exec 12 and the Remote Agent for Linux/Unix Servers (RALUS) to backup a large RHEL5 system. For various reasons we need to do a daily working set job. These working-set jobs run abysmally slow. The link between the target machine and the BE server is gigabit, and any other type of job runs 1-3GB/min. These working-set jobs start out at perhaps 40MB/min and over the course of the backup job slowly drops down so low that the BE job rate display in the "current jobs" goes blank.. Since we usually are only doing changed-files for one day, the job is usually small and finishes overnight and we don't worry abotu the slowness, but we had some issues with the backup server, and missed about 6 days of fairly heavy work on the Linux box, so this working-set job will be a doozy.. We have support with Symantec, and I've pestered them a lot about this, they've had me run RALUS in debug mode, sent them that log and a VXgather from the BE host and they had no fix/workaround.. To give an idea, I have the mentioned working-set job running for the last 3 1/2 hours and it's backed up just under 10MEGAbytes.... I'm posting this here to see if anybody in the "real world" has seen this/and/or has any ideas what might be causing these abysmally slow jobs, since Symantec seems to be clueless...

  Read the article

• Slowness of Netbeans Platform Apps - how to mitigate?

  - by user559298

  Hi, We are developing a commerical application (pretty complex) in java using Netbeans IDE. We have 2 options in netbeans to create it- 1. Develop Java desktop app 2. Netbeans Platform app We have requirement that application startup and response times should be very very fast, should be modular etc. We did Proof of Technology by creating apps using both approaches mentioned above. We found Netbeans platform apps are very slow during startup and during screen navigation compared to pure Swing based desktop apps. We tried to implement suggestions provided at http://wiki.netbeans.org/Category:Performance:FAQ and in other blogs and forums to improve on speed of the app but were not successful. We feel for creating a complex desktop app Netbeans platform app would be better suited, but its not meeting our performance requirements (startup and response times, memory footprints, CPU usage guidelines etc). Can any one guide us on how to mitigate our problem of improving performance of Netbeans Platforms apps? Thanks in advance for your help. -bhan

  Read the article

• slowness in IE 8 IE9 while drawing tables in a html page

  - by GustlyWind

  My HTML page contains many tables,with numerous tr and td. While rendering in IE8/IE9 the its very slow but in Firefox its fast. I had read somewhere while drawing tables if the tables are not of fixed width, IE calculates the width every time and renders so usually slow. Right now i am adding Table style="table-layout:fixed" which made me feel its faster. Are there any similar styles that can be added to tr and td as well.Also suggest if there any other attribtes that can be added to a table

  Read the article

• Relative slowness of SVN compared to perforce when showing revision logs

  - by Reddy

  I have used Perforce previously and in current project we are using SVN. I noticed that it is very slow seeing revision logs and to see its comparisons in SVN relative to Perforce. Is it because Perforce is a commercial solution or is it something with my SVN client(Smart SVN)?

  Read the article

• Xenserver 5.5 U2 a bit unstable with an unstable W2003 VM

  - by twistedbrain

  In the last week I had to reboot the host system twice and the second one by means of the power button. The system is a Dell PE 6950 (4 Opteron dual core, 2,8 Ghz, 16 GB RAM, 900 GB disk in a RAID 10 array composed by 4 450GB 15000 rpm disks) with XenServer 5.5 U2. We're installing it and at now there are working in production a 2003 32 bit Windows server VM with 2 GB RAM, 3 vcpu and about 200 GB disk in 4 partition (12 GB boot, 20 GB program, 80 GB user data, 80 GB other data). The first time I was compressing many Windows 2003 folders (some tens GB by means of W2003 compressed folder option) from a Windows remote console and some hours before my colleague installed Backup Exec agent that was alredy installed and that required a reboot (that was pending). The console stopped responding, it was no more possible to connect by means of remote console or by means of the console of the XenCentre, it was still possible from the network to use the shared folder of the VM and the programs on it (2 db and a GIS program), but the print server didn't work any more and I couldn't give remote reboot from other domain controller hosts. I couldn't stop the virtual machine neither from the XenCentre, neither from the command line of the host also forcing the reboot. I had to reboot the host server. Yesterday it has been worst. I installed a template of another VM, CentOS 5.3 and then, put the DVD in the drive of the host. Then, before the install and after the boot I checked for defect the DVD and the W2003 VM began to respond slowly (I was connected by means of an administration remote console) the task manager showed only mid or low load, it is, only the first of the 3 vcpu was loaded (about 70%), while the other two were about at 20% and also the disk I/O was not so heavy. Then the users were not so happy because they couldn't any more use the MS word docs on the server. I immediately stopped the check of the DVD (to do that I had to force the stop of such Centos 5.3 VM), then some users could again use their docs, but other had still problems, so I decided to reboot the VM, but it doesn't stopped, neither from XenCenter, neither from command line, neither forcing the reboot. Then I tried to reboot of the host, but it didn't worked, neither from the XenCentre, neither from the host prompt (shutdown -r now as root: it told that it was shutting down, but then it didn't did that). So I had to power off by means of the power button of the server (before I tried some Magic SyS REQ, but I saw that Xen isn't compiled with this option enabled). What could you suggest about my problem, what can I look, search and see? In the W2003 VM logs there are no errors or warning to explain what happened. Some more exciting, amusing and inspiring words of poetry (the facts happened around 11 am): \# egrep -i 'err|warning' xensource.log [20100219 10:32:05.597|debug|culo|6301 unix-RPC|VBD.plug R:c81bcda701f6|xenops] watch: watching xenstore paths: [ /xapi/0/frontend/vbd/51712/hotplug; /local/domain/0/backend/vbd/0/51712/tapdisk-error ] with timeout 1200.000000 seconds [20100219 10:32:05.597|debug|culo|6301 unix-RPC|VBD.plug R:c81bcda701f6|xenops] watch: fired on /local/domain/0/backend/vbd/0/51712/tapdisk-error [20100219 10:32:14.314|debug|culo|6335 unix-RPC|VBD.unplug R:9258f54578d6|xenops] watch: watching xenstore paths: [ /local/domain/0/backend/vbd/0/51712/shutdown-done; /local/domain/0/error/device/vbd/51712/error ] with timeout 1200.000000 seconds [20100219 10:32:14.337|debug|culo|6335 unix-RPC|VBD.unplug R:9258f54578d6|xenops] xenstore-rm /local/domain/0/error/backend/vbd/0 [20100219 10:32:14.337|debug|culo|6335 unix-RPC|VBD.unplug R:9258f54578d6|xenops] xenstore-rm /local/domain/0/error/device/vbd/51712 [20100219 10:32:14.338|debug|culo|6335 unix-RPC|VBD.unplug R:9258f54578d6|xenops] watch: fired on /local/domain/0/error/device/vbd/51712/error [20100219 10:53:48.903|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|helpers] Ignoring exception: INTERNAL_ERROR: [ Xb.Noent ] while Vmops.destroy_domain: Destroying domid 14 guest session [20100219 10:53:52.048|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/tap/14 [20100219 10:53:52.048|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vbd/51744 [20100219 10:53:52.085|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/tap/14 [20100219 10:53:52.086|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vbd/51728 [20100219 10:53:52.122|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/tap/14 [20100219 10:53:52.122|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vbd/51712 [20100219 10:53:52.127|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/vbd/14 [20100219 10:53:52.128|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vbd/51760 [20100219 10:53:52.496|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] Device.Vif.hard_shutdown about to blow away backend and error paths [20100219 10:53:52.497|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/vif/14 [20100219 10:53:52.497|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vif/0 [20100219 10:53:53.385|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] Device.Vif.hard_shutdown about to blow away backend and error paths [20100219 10:53:53.386|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/0/error/backend/vif/14 [20100219 10:53:53.386|debug|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|xenops] xenstore-rm /local/domain/14/error/device/vif/1 [20100219 10:53:53.389| warn|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|hotplug] Warning, deleting 'vif' entry from /xapi/14/hotplug/vif/0 [20100219 10:53:53.391| warn|culo|6418|Async.VM.hard_shutdown R:88d2095678f7|hotplug] Warning, deleting 'vif' entry from /xapi/14/hotplug/vif/1 [20100219 11:20:49.766|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|helpers] Ignoring exception: INTERNAL_ERROR: [ Xb.Noent ] while Vmops.destroy_domain: Destroying domid 11 guest session [20100219 11:20:50.339|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/0/error/backend/tap/11 [20100219 11:20:50.339|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/11/error/device/vbd/832 [20100219 11:20:50.360|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/0/error/backend/tap/11 [20100219 11:20:50.360|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/11/error/device/vbd/768 [20100219 11:20:50.366|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/0/error/backend/vbd/11 [20100219 11:20:50.366|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/11/error/device/vbd/5696 [20100219 11:20:50.753|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] Device.Vif.hard_shutdown about to blow away backend and error paths [20100219 11:20:50.754|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/0/error/backend/vif/11 [20100219 11:20:50.754|debug|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|xenops] xenstore-rm /local/domain/11/error/device/vif/1 [20100219 11:20:50.757| warn|culo|6484|Async.VM.clean_shutdown R:78d3c3e28cb6|hotplug] Warning, deleting 'vif' entry from /xapi/11/hotplug/vif/1 [20100219 11:28:13.803|debug|culo|6610 inet-RPC|Connection to VM console R:e9f8b76e8975|console] error: INTERNAL_ERROR: [ Unix.Unix_error(63, "connect", "") ]

  Read the article

• Ubuntu server very slow out of the blue sky (Rails, passenger, nginx)

  - by snitko

  I run Ubuntu server 8.04 on Linode with multiple Rails apps under Passenger + nginx. Today I've noticed it takes quite a lot of time to load a page (5-10 secs). And it's not only websites, ssh seems to be affected too. Having no clue why this may be happening, I started to check different things. I checked how the log files are rotated, I checked if there's enough free disk space and memory. I also checked IO rate, here's the output: $ iostat avg-cpu: %user %nice %system %iowait %steal %idle 0.17 0.00 0.02 0.57 0.16 99.07 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvda 2.25 39.50 16.08 147042 59856 xvdb 0.00 0.05 0.00 192 0 xvdc 2.20 25.93 24.93 96530 92808 xvdd 0.01 0.12 0.00 434 16 xvde 0.04 0.23 0.35 858 1304 xvdf 0.37 0.31 4.12 1162 15352 Rebooting didn't help either. Any ideas where should I be looking?

  Read the article

• How do I troubleshoot system slowness seen when viewing PDFs or videos?

  - by asp

  Whenever I watch videos, either online of local via Totem and/or open PDF files using evince. The system gets really, really bogged down. All apps get really slow, menus take forever to display, switching windows gives me time to make a coffee, etc. I have a couple of bug reports open on this, but what do I need to do to really troubleshoot the issue? I've purged Adobe Flash from the system, but YouTube HTML5 videos still have the issue. A bunch of PDFs saved locally trigger the problem. And to (temporarily) remove the slowness, I need to shutdown the computer, breath for a few minutes, then restart. A simple reboot does not do the trick. How can I identify the cause? This only started on 13.04. I've had Ubuntu on this machine for a year without a problem until "upgrading" to 13.04. I am not a programmer, but I suspect an issue with the Intel video driver. Is there something I can run which will diagnose this, or are there concrete steps I can follow to find the culprit?

  Read the article

• Hitching and Slowness Due to HDD Activity on Ubuntu, But Not Windows?

  - by Espionage724

  It's been bothering me for months now, but I've noticed in Ubuntu (or any distro of Linux I've tried), any major I/O activity will cause hitching and general slowness. For example, if I try doing a file transfer from my network computer to the computer I'm using and try moving the mouse after a while, it might not respond for a second or so. Similar incidents occur in other cases too (right-clicking to get a context menu takes a few seconds, hitting the drop-down application bar takes a while, etc). My HDD isn't top-notch (a WD Blue 500GB 7200RPM drive) but I don't recall it being nearly this bad in Windows 7, 8, or 8.1. CPU activity during file transfers is relatively low (less than 10-20% on all cores of a Phenom II X4 @ 3.3Ghz). I'm using Gnome System Monitor (on Xubuntu) and can't seem to see what kind of HDD activity is occurring though. I have 8GB of RAM too, which is moderately being used (2.5GB), but shouldn't be a problem either. Any ideas what's up? I've tried kernels between 3.8 and 3.11 (i'm using saucy currently with 3.11).

  Read the article

• Why is postgresql update query so slow sometimes, even with index

  - by Matija

  i have a simple update query (foo column type is BOOLEAN (default false)): update tablename set foo = true where id = 234; which "id" is set to (primary) key, and if i run "explain analyze" i got: Index Cond: (id = 234) Total runtime: 0.358 ms but still, i have plenty of unexplained queries at slow log (pgfouine), which took more than 200s (?!): Times executed: 99, Av. duration (s): 70 can anyone please explain, whats the reason for that? (1.5 mio rows in table, postgresql 8.4)

  Read the article

• c# - SQL - speed up code to DB

  - by user228058

  I have a page with 26 sections - one for each letter of the alphabet. I'm retrieving a list of manufacturers from the database, and for each one, creating a link - using a different field in the Database. So currently, I leave the connection open, then do a new SELECT by each letter, WHERE the Name LIKE that letter. It's very slow, though. What's a better way to do this? TIA

  Read the article

• Is there an objective way to measure slowness of PC/WINDOWS?

  - by ekms

  We've a lot of users that usually complain about that his PC is "slow". (we use win XP). We usually check startup programs, virus, fragmentation, disk health and common problems that causes slowness (Symantec AV drops disk to 1mb/s , or a seagate HD firmware error in certain models), but in those cases the slowness is pretty evident. In other hand, the most common is the user complaining about his pc but for us looks OK, even in 6 years old desktops. People sometimes even complains about his new quad core desktops speed!!! So, we are asking if there's a way to OBJECTIVELY check that a computer didn't dropped its performance, compared with similar ones o previous measures, specially for work use (I don't think that 3dmark benchmark o similar may help). The only thing that I found that was useful is HDTune, but it only check hard disk performance. Basically, what we want is something that enable us to say to our users "see? your PC is as slow as was three years ago! stop complaining! Is all in your head!"

  Read the article

1 2 3 4 5 6  | Next Page >