Search Results

Search found 11 results on 1 pages for 'svrguy'.

Page 1/1 | 1 

  • HP ProCurve Port Mode Configuration Question

    - by SvrGuy
    We have a ProCurve Switch 2810-48G (J9022A). We need to disable auto negotiation on two ports and manually configure them to be full duplex gige ports. From the web GUI, Configuration Tab, Port Configuration sub tab, I am only presented with the option to configure the port as Auto - 1000. I take this to mean, auto negotiate duplex, manually configure the speed to be gige. How do I manually configure the port such that it is manually configured to use full duplex, 1000 mbs?

    Read the article

  • Are Colocation Cross Connects Worth While

    - by SvrGuy
    We currently operate three clusters of collocated machines in different data centers. Recently, I became aware that our newest data center will offer to cross connect us to a bandwidth provider free of charge. In the past, I never really investigated a cross connect for bandwidth because I figured that the rates would be similar to what we are paying the colo now and that it would reduce our resiliency (because we would only be using one or two carriers for IP, where as the colo uses, say 8 different providers). Then I saw an ad for hurricane electric internet services (http://he.net/cgi-bin/ip_transit_quote) that gave a price for IP transit at $1/Mbs, which is much better than the $30/Mb we pay for the blended bandwidth. What are people out there typically paying for bandwith via cross connect and how hard is to setup? Is my understanding that what you do is open agreemetns with two or three ISPs, cross connect to them and then configure your top of rack router on their network. Can you really get IP transit down to a couple of dollars per megabit per month just by doing the routing yourself? Or, is my understanding of cross connection fundamentally wrong?

    Read the article

  • HP ProCurve Port Mode Configuration Question Mark 2

    - by SvrGuy
    We have a ProCurve Switch 2810-48G (J9022A). We need to disable auto negotiation on two ports and manually configure them to be full duplex gige ports. From the web GUI, Configuration Tab, Port Configuration sub tab, I am only presented with the option to configure the port as Auto - 1000. I take this to mean, auto negotiate duplex, manually configure the speed to be gige. From the CLI when I try to set 1000-full I get the following error: Value 1000-full is not applicable to port 39 (or whatever port I try) The exact commands I have entered are: config interface 39 speed-duplex 1000-full BTW: speed-duplex auto-1000 works ( I also tried full-1000 and that did not work either) How do I manually configure the port such that it is manually configured to use full duplex, 1000 mbs?

    Read the article

  • PFSense VPN Routing

    - by SvrGuy
    We use PFSense firewalls at three installations with the following LAN networks: 1.) Datacenter #1: 10.0.0.0/16 2.) Datacenter #2: 10.1.0.0/16 3.) HQ: 10.2.0.0/16 All of these locations are linked via an IPSEC tunnel that works properly. Hosts in any of the above networks can communicate with hosts in any other of the above networks. Now, for our laptops etc. we established a road warrior network 10.3.0.0/16 and have implemented OpenVPN to link the laptops etc. to Datacenter #1. This works great too, so our laptops can connect and communicate with any host in Datacenter #1 (anything on 10.0.0.0/16) The problem is the laptops can't communicate with any hosts that Datacenter #1 can reach by its IPSEC tunnel to Datacenter #2 (and/or the HQ for that matter). Does anyone know what to do configuration wise on the PFSense box in Datacenter #1 to configure to route packets received on the OpenVPN tunnel to Datacenter #2 over the IPSEC tunnel? It could be a setting on the OpenVPN or some sort of static route or some such. Any ideas?

    Read the article

  • Symantect (Veritas) Storage Foundation for Windows [closed]

    - by SvrGuy
    Does anyone out their have rough (I don't need exact) pricing for Symantec (used to be Veritas) Storage Foundation for Windows? Its for Windows Server 2008 R2. Ideally, I would love to know the cost of Storange Foundation For Windows, and also the price of the options (like VRR, HA etc. ) if you happen to know them. Getting the information out of a reseller is like pulling teeth. They want to meet with us and discuss our needs etc. My needs are just to know whether its $100, $500, $1,000 or $10,000 per server in small qtys (i.e. less than 20 licences). Arghh. Anyone know the rough prices?

    Read the article

  • Forcing rsync to convert file names to lower case

    - by SvrGuy
    We are using rsync to transfer some (millions) files from a Windows (NTFS/CYGWIN) server to a Linux (RHEL) server. We would like to force all file and directory names on the linux box to be lower case. Is there a way to make rsync automagically convert all file and directory names to lower case? For example, lets say the source file system had a file named: /foo/BAR.gziP Rsync would create (on the destination system) /foo/bar.gzip Obviously, with NTFS being a case insensitive file system there can not be any conflicts... Failing the availability of an rsync option, is there an enhanced build or some other way to achieve this effect? Perhaps a mount option on CYGWIN? Perhaps a similar mount option on Linux? Its RHEL, in case that matters.

    Read the article

  • PFSence VPN Routing

    - by SvrGuy
    We use PFSense firewalls at three installations with the following LAN networks: 1.) Datacenter #1: 10.0.0.0/16 2.) Datacenter #2: 10.1.0.0/16 3.) HQ: 10.2.0.0/16 All of these locations are linked via an IPSEC tunnel that works properly. Hosts in any of the above networks can communicate with hosts in any other of the above networks. Now, for our laptops etc. we established a road warrior network 10.3.0.0/16 and have implemented OpenVPN to link the laptops etc. to Datacenter #1. This works great too, so our laptops can connect and communicate with any host in Datacenter #1 (anything on 10.0.0.0/16) The problem is the laptops can't communicate with any hosts that Datacenter #1 can reach by its IPSEC tunnel to Datacenter #2 (and/or the HQ for that matter). Does anyone know what to do configuration wise on the PFSense box in Datacenter #1 to configure to route packets received on the OpenVPN tunnel to Datacenter #2 over the IPSEC tunnel? It could be a setting on the OpenVPN or some sort of static route or some such. Any ideas?

    Read the article

  • Permissions Issue with Files Generated by PerfMon

    - by SvrGuy
    We are trying to implement some data logging to CSV files using a Data Collector Set in PerfMon (on a windows Server 2008R2 system). The issue we are running into is that we (seemingly) can't control the permissions being set on the log files created by perfmon. What we want is for the log files created by perfmon to have Everyone:F permissions (Full Control for Everyone). So, we have a directory structure setup where all logs go into a folder: c:\vms\PerfMonLogs\%MACHINENAME% (e.g. c:\vms\PerfMonLogs\EvaluationG2) In the above example, c:\vms\PerfMonLogs\EvaluationG2 has permissions Everyone:F (below is the icacls for this directory) EVALUATIONG2/ Everyone:(OI)(CI)(F) NT AUTHORITY\SYSTEM:(OI)(CI)(F) BUILTIN\Administrators:(OI)(CI)(F) BUILTIN\Performance Log Users:(OI)(R) When the data collector set runs, it creates new sub folders and files within c:\vms\PerfMonLogs\EvaluationG2, e.g. (C:\vms\PerfMonLogs\EVALUATIONG2\M11d26y2012N3) Each of these directories and files has the following permissions: M11d26y2012N3 NT AUTHORITY\SYSTEM:(OI)(CI)(F) BUILTIN\Administrators:(OI)(CI)(F) BUILTIN\Performance Log Users:(OI)(R) So these new folders and not simply inheriting permissions from the parent folder (don't know why). Now, we tried adding Everyone:F using the security tab on the collector set (No dice). Any ideas? How do we control the permissions on the log files generated by perfmon data collector set?

    Read the article

  • Java api to get windows Special folders

    - by SvrGuy
    I once found a nifty little library that used JNI to allow java applications on Windows to get the locations of various "special" directories on windows. I can't for the life of me find it again... In particular, I need to get the location of the "All Users" (shared) "Application Data" directory. So, anyone have a bullet proof way in Java to locate the "All Users" "Application Data" folder? It needs to be bullet proof.

    Read the article

  • HTML Rendering Engine as a Java Control

    - by SvrGuy
    Hi All, We have a client side application (Java/Swing) that we need an HTML rendering control for. What I want to find is the most widely adopted, most heavily developed, easiest to deploy solution to get Gecko or WebKit into a Swing app (Needs to run OS X and Windows). The limited (crappy?) JEditPane type solutions are not robust enough for our needs. We would really like to use either WebKit or Gecko. Some libraries seems to exist that would allow this: (QT WebKit) http://trac.webkit.org/wiki/QtWebKit (JRex) [can not post URL because I am new] etc. Whats the best library to achieve this?

    Read the article

  • Finding Errant Output to System.out in Large Java Program

    - by SvrGuy
    Hi, We have a large java code base [~1 M Lines]. Buried (somewhere) in the code base is some old debug output to System.out that we want to remove (its cluttering things up). The problem is: out code base is so large that we can't easily find where the output is coming from. What we want is a way to see where System.out.println is getting called from (like a stack trace from an exception or some such). Its not suitable to debugging -- the errant output is coming from some errant thread somewhere etc. Any ideas on how to track the source of this errant output down? PS: 99.99% of calls to System.out are legit, and we have thousands of them, so simply searching the code base for System.out calls is not a solution!

    Read the article

1