Search Results

Search found 19 results on 1 pages for 'xl2tpd'.

Page 1/1 | 1 

• Openswan + xl2tpd connections time out after a while

  - by Halfgaar

  I have a non-NATed Openswan+xl2tpd server (Ubuntu 12.04), to which I connect with a Windows 8 behind NAT. The client loses its connection after a while of doing nothing (between 30 and 60 minutes, but I didn't time it). The client doesn't have enabled that it should kill inactive connections. Nor does it ever go into sleep mode. I also tried setting the kill-after-time to 24 hours, but that didn't help. The NAT router behind which the client located is Debian Linux, and its router is a Cisco which connects us directly to the data center where the server is. None of our other connections, like SSH, get dropped with inactivity (because of cheap routers). I did however try turning on the keepalives in /etc/ipsec.conf: config setup (...snip...) nat_traversal=yes force_keepalive=yes keep_alive=10 but that didn't help. As you can see in the config later, dead peer detection's action is clear. That would be a first suggestion to fix, but I need clear, because people will be connecting from everwhere but the kitchen sink. Besides, as I said, in the test setup I have now, I can't see any device killing its connection. (edit: 'restart' also has the same effect) These are of one time it happened: Jul 18 16:18:06 host xl2tpd[1918]: Maximum retries exceeded for tunnel 49070. Closing. Jul 18 16:18:06 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 18359 Jul 18 16:18:06 host xl2tpd[1918]: Connection 4 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 16:18:11 host xl2tpd[1918]: Unable to deliver closing message for tunnel 49070. Destroying anyway. and these on another: Jul 18 17:44:39 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 xl2tpd[1918]: last message repeated 4 times Jul 18 17:44:43 host xl2tpd[1918]: Maximum retries exceeded for tunnel 10918. Closing. Jul 18 17:44:43 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:43 host xl2tpd[1918]: Terminating pppd: sending TERM signal to pid 26338 Jul 18 17:44:43 host xl2tpd[1918]: Connection 6 closed to 89.188.x.y, port 1701 (Timeout) Jul 18 17:44:44 host xl2tpd[1918]: udp_xmit failed to 89.188.x.y:1701 with err=-1:Operation not permitted Jul 18 17:44:48 xl2tpd[1918]: last message repeated 3 times Jul 18 17:44:48 host xl2tpd[1918]: Unable to deliver closing message for tunnel 10918. Destroying anyway. Jul 18 17:44:59 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:44:59 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:09 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:09 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:19 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:19 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:29 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:29 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:39 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:39 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Jul 18 17:45:49 host xl2tpd[1918]: Can not find tunnel 10918 (refhim=0) Jul 18 17:45:49 host xl2tpd[1918]: network_thread: unable to find call or tunnel to handle packet. call = 0, tunnel = 10918 Dumping. Versions: Ubuntu 12.04 Openswan: 2.6.37-1 xl2tpd: 3.1+dfsg-1 kernel: 3.2.0-49-generic configs: /etc/ipsec.conf: version 2.0 # conforms to second version of ipsec.conf specification config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:!10.152.2.0/24 oe=off protostack=netkey force_keepalive=yes keep_alive=10 conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=2 rekey=no dpddelay=30 dpdtimeout=120 dpdaction=clear ikelifetime=8h keylife=1h type=transport left=%defaultroute leftprotoport=17/1701 right=%any rightprotoport=17/%any /etc/xl2tpd/xl2tpd.conf [global] ipsec saref = no [lns default] ip range = 10.152.2.2-10.152.2.254 local ip = 10.152.2.1 refuse chap = yes refuse pap = yes require authentication = yes ppp debug = no pppoptfile = /etc/ppp/options.xl2tpd length bit = yes /etc/ppp/options.xl2tpd: require-mschap-v2 refuse-mschap ms-dns 10.152.2.1 asyncmap 0 auth crtscts idle 1800 mtu 1200 mru 1200 lock hide-password local #debug name l2tpd proxyarp lcp-echo-interval 30 lcp-echo-failure 4

  Read the article

• StrongSwan + xl2tpd client timeout between 2-5 minutes

  - by Howard Guo

  I run CentOS 6.4 on Amazon EC2, using xl2tpd-1.3.1 from EPEL repository together with StrongSwan 5.0.4. I setup a simple IPSec connection: conn l2tp type=transport keyexchange=ikev1 rekey=no authby=psk leftsubnet=0.0.0.0/0 rightsubnet=0.0.0.0/0 compress=yes auto=add And here is xl2tpd.conf: [global] ipsec saref = yes [lns default] ip range = 192.168.0.2-192.168.0.250 local ip = 192.168.0.1 ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes Here is options.xl2tpd: ms-dns 8.8.4.4 auth lock debug proxyarp There is only one client - Android 4.2 Android connects successfully: Oct 27 19:45:02 ip-172-31-17-30 xl2tpd[2706]: Connection established to x.x.x.x, 59578. Local: 18934, Remote: 29291 (ref=0/0). LNS session is 'default' Oct 27 19:45:02 ip-172-31-17-30 xl2tpd[2706]: Call established with x.x.x.x, Local: 36452, Remote: 29845, Serial: -1369754322 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: pppd 2.4.5 started by howard, uid 0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Using interface ppp0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Connect: ppp0 <--> /dev/pts/0 Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: peer from calling number x.x.x.x authorized Oct 27 19:45:02 ip-172-31-17-30 pppd[2709]: Deflate (15) compression enabled Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: Cannot determine ethernet address for proxy ARP Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: local IP address 192.168.0.1 Oct 27 19:45:03 ip-172-31-17-30 pppd[2709]: remote IP address 192.168.0.2 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 appeared on ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 disappeared from ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] 192.168.0.1 appeared on ppp0 Oct 27 19:45:03 ip-172-31-17-30 charon: 06[KNL] interface ppp0 activated In the meanwhile, Internet works perfectly on the Android client, the VPN connection is stable and fast. However, it always happens that within 2-5 minutes after the connection is established: Oct 27 19:47:07 ip-172-31-17-30 xl2tpd[2706]: Maximum retries exceeded for tunnel 18934. Closing. Oct 27 19:47:07 ip-172-31-17-30 xl2tpd[2706]: Connection 29291 closed to 95.91.227.224, port 59578 (Timeout) Oct 27 19:47:07 ip-172-31-17-30 charon: 06[KNL] interface ppp0 deactivated Oct 27 19:47:07 ip-172-31-17-30 charon: 06[KNL] interface ppp0 deleted Then the VPN connection is broken. So what might have gone wrong? The same L2TP service works flawlessly on iOS 7, MacOS 10.8, and Windows 7, there is no disconnection issue on those OSes. Thank you!

  Read the article

• L2TP connection fails!

  - by a.toraby

  I've installed l2tp-ipsec-vpn but when I try to connect to the vpn server I get error 500. Here are the logs: Jun 17 12:54:37.449 ipsec_setup: Stopping Openswan IPsec... Jun 17 12:54:38.858 Stopping xl2tpd: xl2tpd. Jun 17 12:54:38.859 xl2tpd[1511]: death_handler: Fatal signal 15 received Jun 17 12:54:38.872 ipsec_setup: Starting Openswan IPsec U2.6.37/K3.2.0-23-generic... Jun 17 12:54:39.027 ipsec__plutorun: Starting Pluto subsystem... Jun 17 12:54:39.033 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d Jun 17 12:54:39.037 recvref[30]: Protocol not available Jun 17 12:54:39.038 xl2tpd[2442]: This binary does not support kernel L2TP. Jun 17 12:54:39.038 xl2tpd[2444]: xl2tpd version xl2tpd-1.3.1 started on atp-ThinkPad-SL410 PID:2444 Jun 17 12:54:39.038 xl2tpd[2444]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. Jun 17 12:54:39.038 xl2tpd[2444]: Forked by Scott Balmos and David Stipp, (C) 2001 Jun 17 12:54:39.038 xl2tpd[2444]: Inherited by Jeff McAdams, (C) 2002 Jun 17 12:54:39.039 xl2tpd[2444]: Forked again by Xelerance (www.xelerance.com) (C) 2006 Jun 17 12:54:39.039 xl2tpd[2444]: Listening on IP address 0.0.0.0, port 1701 Jun 17 12:54:39.040 Starting xl2tpd: xl2tpd. Jun 17 12:54:39.062 ipsec__plutorun: 002 added connection description "L2TP" Jun 17 12:55:30.753 104 "L2TP" #1: STATE_MAIN_I1: initiate Jun 17 12:55:30.754 010 "L2TP" #1: STATE_MAIN_I1: retransmission; will wait 20s for response Jun 17 12:55:30.754 010 "L2TP" #1: STATE_MAIN_I1: retransmission; will wait 40s for response Jun 17 12:55:30.754 003 "L2TP" #1: ignoring Vendor ID payload [MS NT5 ISAKMPOAKLEY 00000008] Jun 17 12:55:30.754 003 "L2TP" #1: received Vendor ID payload [RFC 3947] method set to=109 Jun 17 12:55:30.754 003 "L2TP" #1: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 109 Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [FRAGMENTATION] Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [MS-Negotiation Discovery Capable] Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [IKE CGA version 1] Jun 17 12:55:30.755 106 "L2TP" #1: STATE_MAIN_I2: sent MI2, expecting MR2 Jun 17 12:55:30.755 010 "L2TP" #1: STATE_MAIN_I2: retransmission; will wait 20s for response Jun 17 12:55:30.755 003 "L2TP" #1: NAT-Traversal: Result using RFC 3947 (NAT-Traversal): i am NATed Jun 17 12:55:30.755 108 "L2TP" #1: STATE_MAIN_I3: sent MI3, expecting MR3 Jun 17 12:55:30.756 004 "L2TP" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=oakley_3des_cbc_192 prf=oakley_sha group=modp1024} Jun 17 12:55:30.756 117 "L2TP" #2: STATE_QUICK_I1: initiate Jun 17 12:55:30.756 010 "L2TP" #2: STATE_QUICK_I1: retransmission; will wait 20s for response Jun 17 12:55:30.756 003 "L2TP" #2: ignoring informational payload, type IPSEC_RESPONDER_LIFETIME msgid=6b03ff69 Jun 17 12:55:30.756 003 "L2TP" #2: NAT-Traversal: received 2 NAT-OA. ignored because peer is not NATed Jun 17 12:55:30.756 003 "L2TP" #2: our client subnet returned doesn't match my proposal - us:192.168.1.3/32 vs them:109.162.174.235/32 Jun 17 12:55:30.757 003 "L2TP" #2: Allowing questionable proposal anyway [ALLOW_MICROSOFT_BAD_PROPOSAL] Jun 17 12:55:30.757 004 "L2TP" #2: STATE_QUICK_I2: sent QI2, IPsec SA established transport mode {ESP=>0x23af21f8 <0xdb4a87b6 xfrm=AES_128-HMAC_SHA1 NATOA=none NATD=none DPD=none} Jun 17 12:55:31.759 xl2tpd[2444]: Connecting to host x.x.x.x, port 1701 Jun 17 12:55:32.021 xl2tpd[2444]: Connection established to x.x.x.x, 1701. Local: 4720, Remote: 200 (ref=0/0). Jun 17 12:55:32.023 xl2tpd[2444]: Calling on tunnel 4720 Jun 17 12:55:32.454 xl2tpd[2444]: Call established with x.x.x.x, Local: 9667, Remote: 3, Serial: 1 (ref=0/0) Jun 17 12:55:32.456 xl2tpd[2444]: start_pppd: I'm running: Jun 17 12:55:32.456 xl2tpd[2444]: "/usr/sbin/pppd" Jun 17 12:55:32.457 xl2tpd[2444]: "passive" Jun 17 12:55:32.458 xl2tpd[2444]: "nodetach" Jun 17 12:55:32.458 xl2tpd[2444]: ":" Jun 17 12:55:32.459 xl2tpd[2444]: "file" Jun 17 12:55:32.459 xl2tpd[2444]: "/etc/ppp/L2TP.options.xl2tpd" Jun 17 12:55:32.460 xl2tpd[2444]: "ipparam" Jun 17 12:55:32.461 xl2tpd[2444]: "x.x.x.x" Jun 17 12:55:32.462 xl2tpd[2444]: "/dev/pts/1" Jun 17 12:55:32.583 pppd[2711]: Plugin passprompt.so loaded. Jun 17 12:55:32.583 pppd[2711]: pppd 2.4.5 started by root, uid 0 Jun 17 12:55:32.619 pppd[2711]: Using interface ppp0 Jun 17 12:55:32.620 pppd[2711]: Connect: ppp0 <--> /dev/pts/1 Jun 17 12:55:33.693 pppd[2711]: /usr/bin/L2tpIPsecVpn exited with code 0 Jun 17 12:55:34.454 [ERROR 404] Authentication failed: closing connection to 'L2TP' Jun 17 12:55:34.456 pppd[2711]: MS-CHAP authentication failed: E=691 Authentication failure Jun 17 12:55:34.457 pppd[2711]: CHAP authentication failed Jun 17 12:55:34.461 Stopping xl2tpd: xl2tpd. Jun 17 12:55:34.462 xl2tpd[2444]: death_handler: Fatal signal 15 received Jun 17 12:55:34.463 pppd[2711]: Modem hangup Jun 17 12:55:34.463 pppd[2711]: Connection terminated. Jun 17 12:55:34.474 ipsec_setup: Stopping Openswan IPsec... Jun 17 12:55:34.482 pppd[2711]: Exit. Jun 17 12:55:35.587 ipsec_setup: ERROR: Module xfrm4_mode_transport is in use Jun 17 12:55:35.665 ipsec_setup: ERROR: Module esp4 is in use I had this problem by ubuntu 11.10 though I can easily connect to the server from windows. I use ubuntu 12.0 64bit

  Read the article

• xl2tpd[845]: parse_config: line 13: data 'ipsec sared=yes' occurs with no context

  - by mmc18

  When I executed xl2tpd I amhaving following error. # xl2tpd -D xl2tpd[845]: parse_config: line 13: data 'ipsec sared=yes' occurs with no context xl2tpd[845]: init: Unable to load config file When I remove the "line 13" I having same error with "Line 14" thefore I do not think that the problem is about "ipsec sared" Here is my configuration file xl2tpd.conf. LINUX Ubuntu 12.0.4 ;Openswan IPsec 2.6.37; xl2tpd version: xl2tpd-1.3.1 ; [global] ipsec sared=yes listen-addr=47.168.137.27 ; [lns default] ip range = 192.168.1.10-192.168.1.20 local ip = 192.168.1.1 require chap = yes refuse pap = yes require authentication = yes ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes name=LinuxIPSECVPN ANSWER:(since have not enough reputation I am writting it over here.) removing the ";" character at the beginning of [global] and [lns default] have solved the issue. At fist I tought that [global] and[lns default] were just a comment.

  Read the article

• l2tp server always 'sent [CCP ResetReq id=0x3]' when got compressed data request

  - by wilbur

  I have built a xl2tpd/ipsec server on my ubuntu 12.04.3, and I managed to make a l2tp vpn connection to the xl2tpd server from my android phone. The xl2tpd log said xl2tpd[10828]: Enabling IPsec SAref processing for L2TP transport mode SAs xl2tpd[10828]: IPsec SAref does not work with L2TP kernel mode yet, enabling forceuserspace=yes xl2tpd[10828]: setsockopt recvref[22]: Protocol not available xl2tpd[10828]: This binary does not support kernel L2TP. xl2tpd[10828]: xl2tpd version xl2tpd-1.2.8 started on atime.me PID:10828 xl2tpd[10828]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. xl2tpd[10828]: Forked by Scott Balmos and David Stipp, (C) 2001 xl2tpd[10828]: Inherited by Jeff McAdams, (C) 2002 xl2tpd[10828]: Forked again by Xelerance (www.xelerance.com) (C) 2006 xl2tpd[10828]: Listening on IP address 0.0.0.0, port 1701 xl2tpd[10828]: control_finish: Peer requested tunnel 39154 twice, ignoring second one. xl2tpd[10828]: Connection established to 117.136.8.59, 43149. Local: 25339, Remote: 39154 (ref=0/0). LNS session is 'default' However I cannot access the web in my browser. The pppd log said rcvd [Compressed data] 00 1d 82 c4 7c 04 d8 09 ... sent [CCP ResetReq id=0x7] I have googled a lot and found that this was mostly caused by a mppe decompression error. I have disabled BSD-Compress compression with nobsdcomp in /etc/ppp/xl2tpd-options but it did not work. I used openswan-2.6.33 and xl2tpd-1.2.8 which were built from source. And my configurations: /etc/ipsec.conf version 2.0 config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off protostack=netkey conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 rekey=no ikelifetime=8h keylife=1h type=transport left=106.186.121.214 leftprotoport=17/1701 right=%any rightprotoport=17/%any /etc/xl2tpd/xl2tpd.conf [global] ipsec saref = yes [lns default] local ip = 10.10.11.1 ip range = 10.10.11.2-10.10.11.245 refuse chap = yes refuse pap = yes require authentication = yes ppp debug = yes pppoptfile = /etc/ppp/xl2tpd-options length bit = yes /etc/ppp/xl2tpd-options require-mschap-v2 ms-dns 8.8.8.8 ms-dns 8.8.4.4 asyncmap 0 auth crtscts lock hide-password modem name l2tpd proxyarp lcp-echo-interval 30 lcp-echo-failure 4 debug nobsdcomp Any suggestions? Thanks in advance.

  Read the article

• OpenSwan IPsec connection drops after 30 seconds

  - by drcore

  I'm trying to connection from my Linux Mint 16 box to a CloudStack server. Building up the connection works (pings work across the tunnel). However 30 seconds later the IPsec tunnel gets terminated out of the blue. What could cause this consistent behaviour and how to fix it? The tunnel is setup using OpenSwan (U2.6.38/K(no kernel code presently loaded)) with the L2TP IPsec VPN manager from Werner Jaeger 1.0.9. The client is behind a NAT'ed router and the server is on public IP (CloudStack 4.2) Running ipsec verify complains about IPsec support in kernel. Not sure if this is a problem as the connection is being build up: Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K(no kernel code presently loaded) Checking for IPsec support in kernel [FAILED] SAref kernel support [N/A] Checking that pluto is running [FAILED] whack: Pluto is not running (no "/var/run/pluto/pluto.ctl") Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] Tunnel config: version 2.0 # conforms to second version of ipsec.conf specification config setup # plutodebug="parsing emitting control private" plutodebug=none strictcrlpolicy=no nat_traversal=yes interfaces=%defaultroute oe=off # which IPsec stack to use. netkey,klips,mast,auto or none protostack=netkey conn %default keyingtries=3 pfs=no rekey=yes type=transport left=%defaultroute leftprotoport=17/1701 rightprotoport=17/1701 conn Tunnel1 authby=secret right=37.48.75.97 rightid="" auto=add Log file of VPN connection build up: aug. 23 17:12:54.708 ipsec_setup: Starting Openswan IPsec U2.6.38/K3.11.0-12-generic... aug. 23 17:12:55.155 ipsec_setup: multiple ip addresses, using 192.168.178.32 on eth0 aug. 23 17:12:55.165 ipsec__plutorun: Starting Pluto subsystem... aug. 23 17:12:55.174 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d aug. 23 17:12:55.177 recvref[30]: Protocol not available aug. 23 17:12:55.177 xl2tpd[14339]: This binary does not support kernel L2TP. aug. 23 17:12:55.178 Starting xl2tpd: xl2tpd. aug. 23 17:12:55.178 xl2tpd[14345]: xl2tpd version xl2tpd-1.3.1 started on desktopmint PID:14345 aug. 23 17:12:55.178 xl2tpd[14345]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. aug. 23 17:12:55.179 xl2tpd[14345]: Forked by Scott Balmos and David Stipp, (C) 2001 aug. 23 17:12:55.179 xl2tpd[14345]: Inherited by Jeff McAdams, (C) 2002 aug. 23 17:12:55.179 xl2tpd[14345]: Forked again by Xelerance (www.xelerance.com) (C) 2006 aug. 23 17:12:55.180 xl2tpd[14345]: Listening on IP address 0.0.0.0, port 1701 aug. 23 17:12:55.214 ipsec__plutorun: 002 added connection description "Tunnel1" aug. 23 17:13:15.532 104 "Tunnel1" #1: STATE_MAIN_I1: initiate aug. 23 17:13:15.532 003 "Tunnel1" #1: ignoring unknown Vendor ID payload [4f45755c645c6a795c5c6170] aug. 23 17:13:15.532 003 "Tunnel1" #1: received Vendor ID payload [Dead Peer Detection] aug. 23 17:13:15.533 003 "Tunnel1" #1: received Vendor ID payload [RFC 3947] method set to=115 aug. 23 17:13:15.533 106 "Tunnel1" #1: STATE_MAIN_I2: sent MI2, expecting MR2 aug. 23 17:13:15.534 003 "Tunnel1" #1: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): i am NATed aug. 23 17:13:15.534 108 "Tunnel1" #1: STATE_MAIN_I3: sent MI3, expecting MR3 aug. 23 17:13:15.534 010 "Tunnel1" #1: STATE_MAIN_I3: retransmission; will wait 20s for response aug. 23 17:13:15.545 003 "Tunnel1" #1: received Vendor ID payload [CAN-IKEv2] aug. 23 17:13:15.547 004 "Tunnel1" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_128 prf=oakley_sha group=modp2048} aug. 23 17:13:15.547 117 "Tunnel1" #2: STATE_QUICK_I1: initiate aug. 23 17:13:15.547 010 "Tunnel1" #2: STATE_QUICK_I1: retransmission; will wait 20s for response aug. 23 17:13:15.548 004 "Tunnel1" #2: STATE_QUICK_I2: sent QI2, IPsec SA established transport mode {ESP=>0x0ecef28b <0x3e1fbe3b xfrm=AES_128-HMAC_SHA1 NATOA=none NATD=none DPD=none} aug. 23 17:13:16.549 xl2tpd[14345]: Connecting to host <VPN gateway>, port 1701 aug. 23 17:13:18.576 xl2tpd[14345]: Connection established to <VPN gateway>, 1701. Local: 21163, Remote: 12074 (ref=0/0). aug. 23 17:13:18.576 xl2tpd[14345]: Calling on tunnel 21163 aug. 23 17:13:18.577 xl2tpd[14345]: check_control: Received out of order control packet on tunnel 12074 (got 0, expected 1) aug. 23 17:13:18.577 xl2tpd[14345]: handle_packet: bad control packet! aug. 23 17:13:18.577 xl2tpd[14345]: check_control: Received out of order control packet on tunnel 12074 (got 0, expected 1) aug. 23 17:13:18.577 xl2tpd[14345]: handle_packet: bad control packet! aug. 23 17:13:18.599 xl2tpd[14345]: Call established with <VPN gateway>, Local: 39035, Remote: 57266, Serial: 1 (ref=0/0) aug. 23 17:13:18.605 xl2tpd[14345]: start_pppd: I'm running: aug. 23 17:13:18.605 xl2tpd[14345]: "/usr/sbin/pppd" aug. 23 17:13:18.606 xl2tpd[14345]: "passive" aug. 23 17:13:18.606 xl2tpd[14345]: "nodetach" aug. 23 17:13:18.606 xl2tpd[14345]: ":" aug. 23 17:13:18.606 xl2tpd[14345]: "file" aug. 23 17:13:18.606 xl2tpd[14345]: "/etc/ppp/Tunnel1.options.xl2tpd" aug. 23 17:13:18.606 xl2tpd[14345]: "ipparam" aug. 23 17:13:18.607 xl2tpd[14345]: "<VPN gateway>" aug. 23 17:13:18.607 xl2tpd[14345]: "/dev/pts/4" aug. 23 17:13:18.607 pppd[14438]: Plugin passprompt.so loaded. aug. 23 17:13:18.607 pppd[14438]: pppd 2.4.5 started by root, uid 0 aug. 23 17:13:18.608 pppd[14438]: Using interface ppp0 aug. 23 17:13:18.608 pppd[14438]: Connect: ppp0 <--> /dev/pts/4 aug. 23 17:13:21.650 pppd[14438]: CHAP authentication succeeded: Access granted aug. 23 17:13:21.651 pppd[14438]: CHAP authentication succeeded aug. 23 17:13:21.692 pppd[14438]: local IP address 10.1.2.2 aug. 23 17:13:21.693 pppd[14438]: remote IP address 10.1.2.1 aug. 23 17:13:21.693 pppd[14438]: primary DNS address 10.1.2.1 aug. 23 17:13:21.694 pppd[14438]: secondary DNS address 10.1.2.1 aug. 23 17:13:46.528 Stopping xl2tpd: xl2tpd. aug. 23 17:13:46.528 xl2tpd[14345]: death_handler: Fatal signal 15 received aug. 23 17:13:46.529 pppd[14438]: Modem hangup aug. 23 17:13:46.529 pppd[14438]: Connect time 0.5 minutes. aug. 23 17:13:46.529 pppd[14438]: Sent 1866 bytes, received 1241 bytes. aug. 23 17:13:46.529 pppd[14438]: Connection terminated. aug. 23 17:13:46.562 ipsec_setup: Stopping Openswan IPsec... aug. 23 17:13:46.576 pppd[14438]: Exit.

  Read the article

• installing OpenSwan xl2tpd for IPSEC/L2TP VPN

  - by Shanghai_Phil

  I have a VPS hosted with QuickWeb.co.nz Running Ubuntu 12.04 OpenVZ. I downloaded and unpacked OpenSwan, but I still cannot install: root@vps:~/openswan-2.6.35# apt-get install openswan xl2tpd ppp Reading package lists... Done Building dependency tree... Done Package ppp is not available, but is referred to by another package. This may mean that the package is missing, has been obsoleted, or is only available from another source E: Unable to locate package openswan E: Unable to locate package xl2tpd E: Package 'ppp' has no installation candidate I admit to being a novice, I am learning as I go. Thanks for your patience and help!! :)

  Read the article

• Problem connecting to isp server using xl2tpd as client. Ubuntu server 13.04

  - by Deon Pretorius

  I have followed guides found on google and ubuntu support pages and can get xl2tpd connection up but only under the following conditions: 1 - ADSL model must be configured and connected to the ISP or 2 - ADSL modem in bridge mode I must have an existing PPPoe connection established. If neither of the above are active xl2tpd wont trigger pppd and connect to the isp and thus tunnel connection fails to connect to the L2TP server of the ISP. Am I doing something wrong; /etc/ppp/options.l2tpd.axxess ipcp-accept-local ipcp-accept-remote refuse-eap refuse-chap require-pap noccp noauth idle 1800 mtu 1200 mru 1200 defaultroute usepeerdns debug lock connect-delay 5000 name (name used for ppp connection) /etc/ppp/pap-secrets # * password (name used for ppp connection as above) * (ppp password supplied by isp) /etc/xl2tpd/xl2tpd.conf [global] ; Global parameters: auth file = /etc/xl2tpd/l2tp-secrets ; * Where our challenge secrets are access control = yes ; * Refuse connections without IP match debug tunnel = yes [lac axxess] lns = 196.30.121.50 ; * Who is our LNS? redial = yes ; * Redial if disconnected? redial timeout = 5 ; * Wait n seconds between redials max redials = 5 ; * Give up after n consecutive failures hidden bit = yes ; * User hidden AVP's? length bit = yes ; * Use length bit in payload? require pap = yes ; * Require PAP auth. by peer require chap = no ; * Require CHAP auth. by peer refuse chap = yes ; * Refuse CHAP authentication require authentication = yes ; * Require peer to authenticate name = BLA85003@axxess ; * Report this as our hostname ppp debug = yes ; * Turn on PPP debugging pppoptfile = /etc/ppp/options.l2tpd.axxess ; * ppp options file for this lac /etc/xl2tpd/l2tp-secrets # Secrets for authenticating l2tp tunnels # us them secret # * marko blah2 # zeus marko blah # * * interop * vzb_l2tp (*** secret supplied by isp) ^ isp server host name Any help will be greatly appreciated

  Read the article

• L2TP over IPSec VPN with OpenSwan and XL2TPD can't connect, timeout on Centos 6

  - by Disco

  I'm setting up LT2p over IPSec on my Centos 6.3 fresh install. I have iptables flushed, permit all. Whenever I try to connect, i get a 'no reply from vpn' and nothi Here's my ipsec.conf file (Server is 1.2.3.4) : config setup nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off protostack=netkey conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 rekey=no ikelifetime=8h keylife=1h type=transport left=1.2.3.4 leftprotoport=17/1701 right=%any rightprotoport=17/%any My /etc/ipsec.secrets 1.2.3.4 %any: PSK "password" My sysctl.conf (appened lines) net.ipv4.ip_forward = 1 net.ipv4.conf.default.rp_filter = 0 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.default.send_redirects = 0 net.ipv4.conf.all.log_martians = 0 net.ipv4.conf.default.log_martians = 0 net.ipv4.conf.default.accept_source_route = 0 net.ipv4.conf.all.accept_redirects = 0 net.ipv4.conf.default.accept_redirects = 0 net.ipv4.icmp_ignore_bogus_error_responses = 1 Here's what 'ipsec verify' gives: # ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.32/K2.6.32-279.19.1.el6.x86_64 (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing for disabled ICMP send_redirects [OK] NETKEY detected, testing for disabled ICMP accept_redirects [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] And I see xl2tpd is listening on 1701/udp : udp 0 0 1.2.3.4:1701 0.0.0.0:* 2096/xl2tpd

  Read the article

• OpenSwan + xl2tpd VPN: How can I share Internet connection

  - by Michael

  I have an OpenSwan IPSec + L2TP VPN on Linux setup working from off of my server so I can connect to it from my laptop (roadwarrior setup). I am able to connect to the VPN remotely just fine, however the internet connection is not shared. I'm assuming there is some sort of masquerading I am supposed to be doing, but I have no idea how to go about doing that (iptables?). Any help getting this working so I can essentially use my VPN connection as a proxy would be great. Thanks

  Read the article

• Problem with setup VPN in Ubuntu Server 12.04

  - by Yozone W.

  I have a problem with setup VPN server on my Ubuntu VPS, here is my server environments: Ubuntu Server 12.04 x86_64 xl2tpd 1.3.1+dfsg-1 pppd 2.4.5-5ubuntu1 openswan 1:2.6.38-1~precise1 After install software and configuration: ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K3.2.0-24-virtual (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] /var/log/auth.log message: Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [RFC 3947] method set to=115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] meth=114, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-08] meth=113, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-07] meth=112, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-06] meth=111, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-05] meth=110, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-04] meth=109, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: ignoring Vendor ID payload [FRAGMENTATION 80000000] Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [Dead Peer Detection] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: responding to Main Mode from unknown peer [My IP Address] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R1: sent MR1, expecting MI2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): peer is NATed Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R2: sent MR2, expecting MI3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: Main mode peer ID is ID_IPV4_ADDR: '192.168.12.52' Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: switched from "L2TP-PSK-NAT" to "L2TP-PSK-NAT" Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: new NAT mapping for #5, was [My IP Address]:2251, now [My IP Address]:2847 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_256 prf=oakley_sha group=modp1024} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: the peer proposed: [My Server IP Address]/32:17/1701 -> 192.168.12.52/32:17/0 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: NAT-Traversal: received 2 NAT-OA. using first, ignoring others Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: responding to Quick Mode proposal {msgid:8579b1fb} Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: us: [My Server IP Address]<[My Server IP Address]>:17/1701 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: them: [My IP Address][192.168.12.52]:17/65280===192.168.12.52/32 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x08bda158 <0x4920a374 xfrm=AES_256-HMAC_SHA1 NATOA=192.168.12.52 NATD=[My IP Address]:2847 DPD=enabled} Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA(0x08bda158) payload: deleting IPSEC State #6 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: ERROR: netlink XFRM_MSG_DELPOLICY response for flow eroute_connection delete included errno 2: No such file or directory Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received and ignored informational message Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA payload: deleting ISAKMP State #5 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address]: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:51:16 vpn pluto[3963]: packet from [My IP Address]:2847: received and ignored informational message xl2tpd -D message: xl2tpd[4289]: Enabling IPsec SAref processing for L2TP transport mode SAs xl2tpd[4289]: IPsec SAref does not work with L2TP kernel mode yet, enabling forceuserspace=yes xl2tpd[4289]: setsockopt recvref[30]: Protocol not available xl2tpd[4289]: This binary does not support kernel L2TP. xl2tpd[4289]: xl2tpd version xl2tpd-1.3.1 started on vpn.netools.me PID:4289 xl2tpd[4289]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. xl2tpd[4289]: Forked by Scott Balmos and David Stipp, (C) 2001 xl2tpd[4289]: Inherited by Jeff McAdams, (C) 2002 xl2tpd[4289]: Forked again by Xelerance (www.xelerance.com) (C) 2006 xl2tpd[4289]: Listening on IP address [My Server IP Address], port 1701 Then it just stopped here, and have no any response. I can't connect VPN on my mac client, the /var/log/system.log message: Oct 16 15:17:36 azone-iMac.local configd[17]: SCNC: start, triggered by SystemUIServer, type L2TP, status 0 Oct 16 15:17:36 azone-iMac.local pppd[3799]: pppd 2.4.2 (Apple version 596.13) started by azone, uid 501 Oct 16 15:17:38 azone-iMac.local pppd[3799]: L2TP connecting to server 'vpn.netools.me' ([My Server IP Address])... Oct 16 15:17:38 azone-iMac.local pppd[3799]: IPSec connection started Oct 16 15:17:38 azone-iMac.local racoon[359]: Connecting. Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 started (Initiated by me). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 2). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 3). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 4). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 5). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 AUTH: success. (Initiator, Main-Mode Message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 Initiator: success. (Initiator, Main-Mode). Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 started (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local pppd[3799]: IPSec connection established Oct 16 15:17:59 azone-iMac.local pppd[3799]: L2TP cannot connect to the server Oct 16 15:17:59 azone-iMac.local racoon[359]: IPSec disconnecting from server [My Server IP Address] Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Anyone help? Thanks a million!

  Read the article

• Problem with setup VPN on Ubuntu Server 12.04

  - by Yozone W.

  I have a problem with setup VPN server on my Ubuntu VPS, here is my server environments: Ubuntu Server 12.04 x86_64 xl2tpd 1.3.1+dfsg-1 pppd 2.4.5-5ubuntu1 openswan 1:2.6.38-1~precise1 After install software and configuration: ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K3.2.0-24-virtual (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] /var/log/auth.log message: Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [RFC 3947] method set to=115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] meth=114, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-08] meth=113, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-07] meth=112, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-06] meth=111, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-05] meth=110, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-04] meth=109, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: ignoring Vendor ID payload [FRAGMENTATION 80000000] Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [Dead Peer Detection] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: responding to Main Mode from unknown peer [My IP Address] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R1: sent MR1, expecting MI2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): peer is NATed Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R2: sent MR2, expecting MI3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: Main mode peer ID is ID_IPV4_ADDR: '192.168.12.52' Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: switched from "L2TP-PSK-NAT" to "L2TP-PSK-NAT" Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: new NAT mapping for #5, was [My IP Address]:2251, now [My IP Address]:2847 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_256 prf=oakley_sha group=modp1024} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: the peer proposed: [My Server IP Address]/32:17/1701 -> 192.168.12.52/32:17/0 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: NAT-Traversal: received 2 NAT-OA. using first, ignoring others Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: responding to Quick Mode proposal {msgid:8579b1fb} Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: us: [My Server IP Address]<[My Server IP Address]>:17/1701 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: them: [My IP Address][192.168.12.52]:17/65280===192.168.12.52/32 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x08bda158 <0x4920a374 xfrm=AES_256-HMAC_SHA1 NATOA=192.168.12.52 NATD=[My IP Address]:2847 DPD=enabled} Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA(0x08bda158) payload: deleting IPSEC State #6 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: ERROR: netlink XFRM_MSG_DELPOLICY response for flow eroute_connection delete included errno 2: No such file or directory Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received and ignored informational message Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA payload: deleting ISAKMP State #5 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address]: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:51:16 vpn pluto[3963]: packet from [My IP Address]:2847: received and ignored informational message xl2tpd -D message: xl2tpd[4289]: Enabling IPsec SAref processing for L2TP transport mode SAs xl2tpd[4289]: IPsec SAref does not work with L2TP kernel mode yet, enabling forceuserspace=yes xl2tpd[4289]: setsockopt recvref[30]: Protocol not available xl2tpd[4289]: This binary does not support kernel L2TP. xl2tpd[4289]: xl2tpd version xl2tpd-1.3.1 started on vpn.netools.me PID:4289 xl2tpd[4289]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. xl2tpd[4289]: Forked by Scott Balmos and David Stipp, (C) 2001 xl2tpd[4289]: Inherited by Jeff McAdams, (C) 2002 xl2tpd[4289]: Forked again by Xelerance (www.xelerance.com) (C) 2006 xl2tpd[4289]: Listening on IP address [My Server IP Address], port 1701 Then it just stopped here, and have no any response. I can't connect VPN on my mac client, the /var/log/system.log message: Oct 16 15:17:36 azone-iMac.local configd[17]: SCNC: start, triggered by SystemUIServer, type L2TP, status 0 Oct 16 15:17:36 azone-iMac.local pppd[3799]: pppd 2.4.2 (Apple version 596.13) started by azone, uid 501 Oct 16 15:17:38 azone-iMac.local pppd[3799]: L2TP connecting to server 'vpn.netools.me' ([My Server IP Address])... Oct 16 15:17:38 azone-iMac.local pppd[3799]: IPSec connection started Oct 16 15:17:38 azone-iMac.local racoon[359]: Connecting. Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 started (Initiated by me). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 2). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 3). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 4). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 5). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 AUTH: success. (Initiator, Main-Mode Message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 Initiator: success. (Initiator, Main-Mode). Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 started (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local pppd[3799]: IPSec connection established Oct 16 15:17:59 azone-iMac.local pppd[3799]: L2TP cannot connect to the server Oct 16 15:17:59 azone-iMac.local racoon[359]: IPSec disconnecting from server [My Server IP Address] Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Anyone help? Thanks a million!

  Read the article

• Setup VPN issue on Ubuntu Server 12.04

  - by Yozone W.

  I have a problem with setup VPN server on my Ubuntu VPS, here is my server environments: Ubuntu Server 12.04 x86_64 xl2tpd 1.3.1+dfsg-1 pppd 2.4.5-5ubuntu1 openswan 1:2.6.38-1~precise1 After install software and configuration: ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K3.2.0-24-virtual (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] /var/log/auth.log message: Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [RFC 3947] method set to=115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] meth=114, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-08] meth=113, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-07] meth=112, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-06] meth=111, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-05] meth=110, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-04] meth=109, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 115 Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: ignoring Vendor ID payload [FRAGMENTATION 80000000] Oct 16 06:50:54 vpn pluto[3963]: packet from [My IP Address]:2251: received Vendor ID payload [Dead Peer Detection] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: responding to Main Mode from unknown peer [My IP Address] Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Oct 16 06:50:54 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R1: sent MR1, expecting MI2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): peer is NATed Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: STATE_MAIN_R2: sent MR2, expecting MI3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: Main mode peer ID is ID_IPV4_ADDR: '192.168.12.52' Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[5] [My IP Address] #5: switched from "L2TP-PSK-NAT" to "L2TP-PSK-NAT" Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: new NAT mapping for #5, was [My IP Address]:2251, now [My IP Address]:2847 Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_256 prf=oakley_sha group=modp1024} Oct 16 06:50:55 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: the peer proposed: [My Server IP Address]/32:17/1701 -> 192.168.12.52/32:17/0 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: NAT-Traversal: received 2 NAT-OA. using first, ignoring others Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: responding to Quick Mode proposal {msgid:8579b1fb} Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: us: [My Server IP Address]<[My Server IP Address]>:17/1701 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: them: [My IP Address][192.168.12.52]:17/65280===192.168.12.52/32 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: Dead Peer Detection (RFC 3706): enabled Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Oct 16 06:50:56 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #6: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x08bda158 <0x4920a374 xfrm=AES_256-HMAC_SHA1 NATOA=192.168.12.52 NATD=[My IP Address]:2847 DPD=enabled} Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA(0x08bda158) payload: deleting IPSEC State #6 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: ERROR: netlink XFRM_MSG_DELPOLICY response for flow eroute_connection delete included errno 2: No such file or directory Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received and ignored informational message Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address] #5: received Delete SA payload: deleting ISAKMP State #5 Oct 16 06:51:16 vpn pluto[3963]: "L2TP-PSK-NAT"[6] [My IP Address]: deleting connection "L2TP-PSK-NAT" instance with peer [My IP Address] {isakmp=#0/ipsec=#0} Oct 16 06:51:16 vpn pluto[3963]: packet from [My IP Address]:2847: received and ignored informational message xl2tpd -D message: xl2tpd[4289]: Enabling IPsec SAref processing for L2TP transport mode SAs xl2tpd[4289]: IPsec SAref does not work with L2TP kernel mode yet, enabling forceuserspace=yes xl2tpd[4289]: setsockopt recvref[30]: Protocol not available xl2tpd[4289]: This binary does not support kernel L2TP. xl2tpd[4289]: xl2tpd version xl2tpd-1.3.1 started on vpn.netools.me PID:4289 xl2tpd[4289]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. xl2tpd[4289]: Forked by Scott Balmos and David Stipp, (C) 2001 xl2tpd[4289]: Inherited by Jeff McAdams, (C) 2002 xl2tpd[4289]: Forked again by Xelerance (www.xelerance.com) (C) 2006 xl2tpd[4289]: Listening on IP address [My Server IP Address], port 1701 Then it just stopped here, and have no any response. I can't connect VPN on my mac client, the /var/log/system.log message: Oct 16 15:17:36 azone-iMac.local configd[17]: SCNC: start, triggered by SystemUIServer, type L2TP, status 0 Oct 16 15:17:36 azone-iMac.local pppd[3799]: pppd 2.4.2 (Apple version 596.13) started by azone, uid 501 Oct 16 15:17:38 azone-iMac.local pppd[3799]: L2TP connecting to server 'vpn.netools.me' ([My Server IP Address])... Oct 16 15:17:38 azone-iMac.local pppd[3799]: IPSec connection started Oct 16 15:17:38 azone-iMac.local racoon[359]: Connecting. Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 started (Initiated by me). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 2). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 3). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 4). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Main-Mode message 5). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 AUTH: success. (Initiator, Main-Mode Message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Main-Mode message 6). Oct 16 15:17:38 azone-iMac.local racoon[359]: IKEv1 Phase1 Initiator: success. (Initiator, Main-Mode). Oct 16 15:17:38 azone-iMac.local racoon[359]: IPSec Phase1 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 started (Initiated by me). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Oct 16 15:17:39 azone-iMac.local racoon[359]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Oct 16 15:17:39 azone-iMac.local racoon[359]: IPSec Phase2 established (Initiated by me). Oct 16 15:17:39 azone-iMac.local pppd[3799]: IPSec connection established Oct 16 15:17:59 azone-iMac.local pppd[3799]: L2TP cannot connect to the server Oct 16 15:17:59 azone-iMac.local racoon[359]: IPSec disconnecting from server [My Server IP Address] Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete IPSEC-SA). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKE Packet: transmit success. (Information message). Oct 16 15:17:59 azone-iMac.local racoon[359]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Anyone help? Thanks a million!

  Read the article

• Setting up VPN client: L2TP with IPsec

  - by zachar

  I've got to connect to vpn server. It works on Windows, but in Ubuntu 10.04 not. Number of options is confusing for me. There is the input that I have: IP Address of VPN Pre-shared key to authenticate Information that MS-CHAPv2 is used Login and Password to VPN I was trying to achive that with network manager and with L2TP IPsec VPN Manager 1.0.9 but at failed. There is some logged information from L2TP IPsec VPN Manager 1.0.9: Nov 09 15:21:46.854 ipsec_setup: Stopping Openswan IPsec... Nov 09 15:21:48.088 Stopping xl2tpd: xl2tpd. Nov 09 15:21:48.132 ipsec_setup: Starting Openswan IPsec U2.6.23/K2.6.32-49-generic... Nov 09 15:21:48.308 ipsec__plutorun: Starting Pluto subsystem... Nov 09 15:21:48.318 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d Nov 09 15:21:48.338 ipsec__plutorun: 002 added connection description "my_vpn_name" Nov 09 15:21:48.348 ipsec__plutorun: 003 NAT-Traversal: Trying new style NAT-T Nov 09 15:21:48.348 ipsec__plutorun: 003 NAT-Traversal: ESPINUDP(1) setup failed for new style NAT-T family IPv4 (errno=19) Nov 09 15:21:48.349 ipsec__plutorun: 003 NAT-Traversal: Trying old style NAT-T Nov 09 15:21:48.994 104 "my_vpn_name" #1: STATE_MAIN_I1: initiate Nov 09 15:21:48.994 003 "my_vpn_name" #1: received Vendor ID payload [RFC 3947] method set to=109 Nov 09 15:21:48.994 003 "my_vpn_name" #1: received Vendor ID payload [Dead Peer Detection] Nov 09 15:21:48.994 106 "my_vpn_name" #1: STATE_MAIN_I2: sent MI2, expecting MR2 Nov 09 15:21:48.994 003 "my_vpn_name" #1: NAT-Traversal: Result using RFC 3947 (NAT-Traversal): i am NATed Nov 09 15:21:48.994 108 "my_vpn_name" #1: STATE_MAIN_I3: sent MI3, expecting MR3 Nov 09 15:21:48.994 004 "my_vpn_name" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=oakley_3des_cbc_192 prf=oakley_sha group=modp1024} Nov 09 15:21:48.995 117 "my_vpn_name" #2: STATE_QUICK_I1: initiate Nov 09 15:21:48.995 004 "my_vpn_name" #2: STATE_QUICK_I2: sent QI2, IPsec SA established transport mode {ESP=>0x0c96795d <0x483e1a42 xfrm=AES_128-HMAC_SHA1 NATOA=none NATD=none DPD=none} Nov 09 15:21:49.996 [ERROR 210] Failed to open l2tp control file 'c my_vpn_name' and from syslog: Nov 9 15:21:46 o99 L2tpIPsecVpnControlDaemon: Opening client connection Nov 9 15:21:46 o99 L2tpIPsecVpnControlDaemon: Executing command ipsec setup stop Nov 9 15:21:46 o99 ipsec_setup: Stopping Openswan IPsec... Nov 9 15:21:48 o99 kernel: [ 4350.245171] NET: Unregistered protocol family 15 Nov 9 15:21:48 o99 ipsec_setup: ...Openswan IPsec stopped Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command ipsec setup stop finished with exit code 0 Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Executing command invoke-rc.d xl2tpd stop Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command invoke-rc.d xl2tpd stop finished with exit code 0 Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Opening client connection Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Closing client connection Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Executing command ipsec setup start Nov 9 15:21:48 o99 kernel: [ 4350.312483] NET: Registered protocol family 15 Nov 9 15:21:48 o99 ipsec_setup: Starting Openswan IPsec U2.6.23/K2.6.32-49-generic... Nov 9 15:21:48 o99 ipsec_setup: Using NETKEY(XFRM) stack Nov 9 15:21:48 o99 kernel: [ 4350.410774] Initializing XFRM netlink socket Nov 9 15:21:48 o99 kernel: [ 4350.413601] padlock: VIA PadLock not detected. Nov 9 15:21:48 o99 kernel: [ 4350.427311] padlock: VIA PadLock Hash Engine not detected. Nov 9 15:21:48 o99 kernel: [ 4350.441533] padlock: VIA PadLock not detected. Nov 9 15:21:48 o99 ipsec_setup: ...Openswan IPsec started Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command ipsec setup start finished with exit code 0 Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Executing command invoke-rc.d xl2tpd start Nov 9 15:21:48 o99 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d Nov 9 15:21:48 o99 pluto: adjusting ipsec.d to /etc/ipsec.d Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command invoke-rc.d xl2tpd start finished with exit code 0 Nov 9 15:21:48 o99 ipsec__plutorun: 002 added connection description "my_vpn_name" Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Executing command ipsec auto --ready Nov 9 15:21:48 o99 ipsec__plutorun: 003 NAT-Traversal: Trying new style NAT-T Nov 9 15:21:48 o99 ipsec__plutorun: 003 NAT-Traversal: ESPINUDP(1) setup failed for new style NAT-T family IPv4 (errno=19) Nov 9 15:21:48 o99 ipsec__plutorun: 003 NAT-Traversal: Trying old style NAT-T Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command ipsec auto --ready finished with exit code 0 Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Executing command ipsec auto --up my_vpn_name Nov 9 15:21:48 o99 L2tpIPsecVpnControlDaemon: Command ipsec auto --up my_vpn_name finished with exit code 0 Nov 9 15:21:49 o99 L2tpIPsecVpnControlDaemon: Closing client connection Can anyone tell me something more about that? Where is the mistake?

  Read the article

• Can't get the L2TP IPSEC up and running

  - by Maciej Swic

  i have an Ubuntu 11.10 (oneiric) server running on a ReadyNAS. Im planning to use this to accept ipsec+l2tp connections through a router. However, the connection is failing somewhere half through. Using Openswan IPsec U2.6.28/K3.0.0-12-generic and trying to connect with an iOS 5 iPhone 4S. This is how far i can get: auth.log: Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "PSK" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "L2TP-PSK-NAT" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "L2TP-PSK-noNAT" Jan 19 13:54:11 ubuntu pluto[1990]: added connection description "passthrough-for-non-l2tp" Jan 19 13:54:11 ubuntu pluto[1990]: listening for IKE messages Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: Trying new style NAT-T Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: ESPINUDP(1) setup failed for new style NAT-T family IPv4 (errno=19) Jan 19 13:54:11 ubuntu pluto[1990]: NAT-Traversal: Trying old style NAT-T Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 192.168.19.99:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 192.168.19.99:4500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo 127.0.0.1:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo 127.0.0.1:4500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface lo/lo ::1:500 Jan 19 13:54:11 ubuntu pluto[1990]: adding interface eth0/eth0 2001:470:28:81:a00:27ff:* Jan 19 13:54:11 ubuntu pluto[1990]: loading secrets from "/etc/ipsec.secrets" Jan 19 13:54:11 ubuntu pluto[1990]: loading secrets from "/var/lib/openswan/ipsec.secrets.inc" Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [RFC 3947] method set to=109 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] method set to=110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [8f8d83826d246b6fc7a8a6a428c11de8] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [439b59f8ba676c4c7737ae22eab8f582] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [4d1e0e136deafa34c4f3ea9f02ec7285] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [80d0bb3def54565ee84645d4c85ce3ee] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: ignoring unknown Vendor ID payload [9909b64eed937c6573de52ace952fa6b] Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 110 Jan 19 14:04:31 ubuntu pluto[1990]: packet from 95.*.*.233:500: received Vendor ID payload [Dead Peer Detection] Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: responding to Main Mode from unknown peer 95.*.*.233 Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Jan 19 14:04:31 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: STATE_MAIN_R1: sent MR1, expecting MI2 Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): both are NATed Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Jan 19 14:04:33 ubuntu pluto[1990]: "PSK"[1] 95.*.*.233 #1: STATE_MAIN_R2: sent MR2, expecting MI3 Jan 19 14:05:03 ubuntu pluto[1990]: ERROR: asynchronous network error report on eth0 (sport=500) for message to 95.*.*.233 port 500, complainant 95.*.*.233: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] Router config UDP 500, 1701 and 4500 forwarded to 192.168.19.99 (Ubuntu server for ipsec). Ipsec passthrough enabled. /etc/ipsec.conf # /etc/ipsec.conf - Openswan IPsec configuration file # This file: /usr/share/doc/openswan/ipsec.conf-sample # # Manual: ipsec.conf.5 version 2.0 # conforms to second version of ipsec.conf specification config setup nat_traversal=yes #charonstart=yes #plutostart=yes protostack=netkey conn PSK authby=secret forceencaps=yes pfs=no auto=add keyingtries=3 dpdtimeout=60 dpdaction=clear rekey=no left=192.168.19.99 leftnexthop=192.168.19.1 leftprotoport=17/1701 right=%any rightprotoport=17/%any rightsubnet=vhost:%priv,%no dpddelay=10 #dpdtimeout=10 #dpdaction=clear include /etc/ipsec.d/l2tp-psk.conf /etc/ipsec.d/l2tp-psk.conf conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT # # PreSharedSecret needs to be specified in /etc/ipsec.secrets as # YourIPAddress %any: "sharedsecret" authby=secret pfs=no auto=add keyingtries=3 # we cannot rekey for %any, let client rekey rekey=no # Set ikelifetime and keylife to same defaults windows has ikelifetime=8h keylife=1h # l2tp-over-ipsec is transport mode type=transport # left=192.168.19.99 # # For updated Windows 2000/XP clients, # to support old clients as well, use leftprotoport=17/%any leftprotoport=17/1701 # # The remote user. # right=%any # Using the magic port of "0" means "any one single port". This is # a work around required for Apple OSX clients that use a randomly # high port, but propose "0" instead of their port. rightprotoport=17/%any dpddelay=10 dpdtimeout=10 dpdaction=clear conn passthrough-for-non-l2tp type=passthrough left=192.168.19.99 leftnexthop=192.168.19.1 right=0.0.0.0 rightsubnet=0.0.0.0/0 auto=route /etc/ipsec.secrets include /var/lib/openswan/ipsec.secrets.inc %any %any: PSK "my-key" 192.168.19.99 %any: PSK "my-key" /etc/xl2tpd/xl2tpd.conf [global] debug network = yes debug tunnel = yes ipsec saref = no listen-addr = 192.168.19.99 [lns default] ip range = 192.168.19.201-192.168.19.220 local ip = 192.168.19.99 require chap = yes refuse chap = no refuse pap = no require authentication = no ppp debug = yes pppoptfile = /etc/ppp/options.xl2tpd length bit = yes /etc/ppp/options.xl2tpd pcp-accept-local ipcp-accept-remote noccp auth crtscts idle 1800 mtu 1410 mru 1410 defaultroute debug lock proxyarp connect-delay 5000 ipcp-accept-local /etc/ppp/chap-secrets # Secrets for authentication using CHAP # client server secret IP addresses maciekish * my-secret * * maciekish my-secret * I can't seem to find the problem. Other ipsec connections to other hosts work from the network im currently at.

  Read the article

• How do I limit one connection per user for L2TP/IPSec using OpenSwan?

  - by Han

  I've successfully set up a VPN server with openswan, pppd, and xl2tpd on Ubuntu. Everything works great, but I'm having trouble finding out how to only allow one VPN connection per user listed in the /etc/ppp/chap-secrets file? Right now a user can have unlimited connections which is worrisome to me as I've shared access to the VPN with some friends but am worried they might keep spreading the username/password.

  Read the article

• Windows 7 keep internet connection after IPSec established

  - by mmc18

  How I can keep internet connection after establishing IpSec connection to server? I have followed to following link to establihed IpSec server http://rootmanager.com/ubuntu-ipsec-l2tp-windows-domain-auth/setting-up-openswan-xl2tpd-with-native-windows-clients.html then following the below one to connect this server from Windows 7 machine. http://confoundedtech.blogspot.com/2012/07/windows-l2tp-ipsec-vpn-connection-to.html I am able to connect and properly sending data. But after establihing IpSec conenction, my internet conenction is dropped. How I can keep both connection alive?

  Read the article

• l2tp / ipsec debian Openswan U2.6.38 does not connect

  - by locojay

  i am trying to get ipsec/l2tp running on a debian server with an iphone as a client but always get: Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [RFC 3947] method set to=115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] meth=114, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-08] meth=113, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-07] meth=112, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-06] meth=111, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-05] meth=110, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-04] meth=109, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: ignoring Vendor ID payload [FRAGMENTATION 80000000] Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [Dead Peer Detection] Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: responding to Main Mode from unknown peer <clientip> Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: STATE_MAIN_R1: sent MR1, expecting MI2 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): both are NATed Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: STATE_MAIN_R2: sent MR2, expecting MI3 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: Main mode peer ID is ID_IPV4_ADDR: '10.2.210.176' Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: switched from "L2TP-PSK-noNAT" to "L2TP-PSK-noNAT" Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: deleting connection "L2TP-PSK-noNAT" instance with peer <clientip> {isakmp=#0/ipsec=#0} Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: new NAT mapping for #20, was <clientip>:43598, now <clientip>:49826 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_256 prf=oakley_sha group=modp1024} Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: Dead Peer Detection (RFC 3706): enabled Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: the peer proposed: <public ip>/32:17/1701 -> 10.2.210.176/32:17/0 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: NAT-Traversal: received 2 NAT-OA. using first, ignoring others Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: responding to Quick Mode proposal {msgid:311d3282} Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: us: 171.138.2.13<171.138.2.13>:17/1701 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: them: <clientip>[10.2.210.176]:17/61719 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: Dead Peer Detection (RFC 3706): enabled Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x05e23c9a <0x216077a9 xfrm=AES_256-HMAC_SHA1 NATOA=10.2.210.176 NATD=<clientip>:49826 DPD=enabled} Dec 2 21:00:26 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received Delete SA(0x05e23c9a) payload: deleting IPSEC State #21 Dec 2 21:00:26 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received and ignored informational message Dec 2 21:00:27 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received Delete SA payload: deleting ISAKMP State #20 Dec 2 21:00:27 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip>: deleting connection "L2TP-PSK-noNAT" instance with peer <clientip> {isakmp=#0/ipsec=#0} Dec 2 21:00:27 vpn pluto[22711]: packet from <clientip>:49826: received and ignored informational message Dec 2 21:00:27 vpn pluto[22711]: ERROR: asynchronous network error report on eth0 (sport=4500) for message to <clientip> port 49826, complainant <clientip>: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] my setup looks like this verizon fios actiontec -- DMZ-- ddwrt router -- debian xen instance actiontec : 192.168.1.1 ddwrt: 171.138.2.1 debian xen server: 171.138.2.13 forwarded udp 500, 4500, 1701 on ddwrt to debian xen instance. vpn passthrough is enabled /etc/ipsec.conf config setup dumpdir=/var/run/pluto/ nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:25.0.0.0/8,%v6:fd00::/8,%v6:fe80::/10,%v4:!171.138.2.0/24,%v4:!192.168.1.0/24 protostack=netkey # Add connections here conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 # we cannot rekey for %any, let client rekey rekey=no # Apple iOS doesn't send delete notify so we need dead peer detection # to detect vanishing clients dpddelay=30 dpdtimeout=120 dpdaction=clear # Set ikelifetime and keylife to same defaults windows has ikelifetime=8h keylife=1h # l2tp-over-ipsec is transport mode type=transport # left=171.138.2.13 # # For updated Windows 2000/XP clients, # to support old clients as well, use leftprotoport=17/%any leftprotoport=17/1701 # # The remote user. # right=%any # Using the magic port of "%any" means "any one single port". This is # a work around required for Apple OSX clients that use a randomly # high port. rightprotoport=17/%any #force all to be nat'ed. because of ios conn passthrough-for-non-l2tp type=passthrough left=171.138.2.13 leftnexthop=171.138.2.1 right=0.0.0.0 rightsubnet=0.0.0.0/0 auto=route /etc/xl2tp/xl2tp.conf [global] ipsec saref = no listen-addr = 171.138.2.13 ;port = 1701 ;debug network = yes ;debug tunnel = yes ;debug network = yes ;debug packet = yes [lns default] ip range = 171.138.2.231-171.138.2.239 local ip = 171.138.2.13 assign ip = yes require chap = no refuse pap = no require authentication = no ;name = OpenswanVPN ppp debug = yes pppoptfile = /etc/ppp/options.xlt2tpd lenght bit = yes /etc/ppp/options.xl2tpd ;require-mschap-v2 pcp-accept-local ipcp-accept-local ipcp-accept-remote ;ms-dns 171.138.2.1 ms-dns 192.168.1.1 ms-dns 8.8.8.8 name l2tpd noccp auth crtscts idle 1800 mtu 1410 mru 1410 lock proxyarp connect-delay 5000 debug dump logfd 2 logfile /var/log/xl2tpd.log ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K3.0.0-1-amd64 (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Two or more interfaces found, checking IP forwarding [FAILED] Checking NAT and MASQUERADEing [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] The failed can be ignored i guess since cat /proc/sys/net/ipv4/ip_forward returns 1 any help would be much appreciated as i don't have any idea why this is not working

  Read the article

• How to access remote lan machines through a ipsec / xl2ptd vpn (maybe iptables related)

  - by Simon

  I’m trying to do the setup of a IPSEC / XL2TPD VPN for our office, and I’m having some problems accessing the remote local machines after connecting to the VPN. I can connect, and I can browse Internet sites trough the VPN, but as said, I’m unable to connect or even ping the local ones. My Network setup is something like this: INTERNET eth0 ROUTER / VPN eth2 LAN These are some traceroutes behind the VPN: traceroute to google.com (173.194.78.94), 64 hops max, 52 byte packets 1 192.168.1.80 (192.168.1.80) 74.738 ms 71.476 ms 70.123 ms 2 10.35.192.1 (10.35.192.1) 77.832 ms 77.578 ms 77.865 ms 3 10.47.243.137 (10.47.243.137) 78.837 ms 85.409 ms 76.032 ms 4 10.47.242.129 (10.47.242.129) 78.069 ms 80.054 ms 77.778 ms 5 10.254.4.2 (10.254.4.2) 86.174 ms 10.254.4.6 (10.254.4.6) 85.687 ms 10.254.4.2 (10.254.4.2) 85.664 ms traceroute to 192.168.1.3 (192.168.1.3), 64 hops max, 52 byte packets 1 * * * 2 *traceroute: sendto: No route to host traceroute: wrote 192.168.1.3 52 chars, ret=-1 *traceroute: sendto: Host is down traceroute: wrote 192.168.1.3 52 chars, ret=-1 * traceroute: sendto: Host is down 3 traceroute: wrote 192.168.1.3 52 chars, ret=-1 *traceroute: sendto: Host is down traceroute: wrote 192.168.1.3 52 chars, ret=-1 These are my iptables rules: iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT # allow lan to router traffic iptables -A INPUT -s 192.168.1.0/24 -i eth2 -j ACCEPT # ssh iptables -A INPUT -p tcp --dport ssh -j ACCEPT # vpn iptables -A INPUT -p 50 -j ACCEPT iptables -A INPUT -p ah -j ACCEPT iptables -A INPUT -p udp --dport 500 -j ACCEPT iptables -A INPUT -p udp --dport 4500 -j ACCEPT iptables -A INPUT -p udp --dport 1701 -j ACCEPT # dns iptables -A INPUT -s 192.168.1.0/24 -p tcp --dport 53 -j ACCEPT iptables -A INPUT -s 192.168.1.0/24 -p udp --dport 53 -j ACCEPT iptables -t nat -A POSTROUTING -j MASQUERADE # logging iptables -I INPUT 5 -m limit --limit 1/min -j LOG --log-prefix "iptables denied: " --log-level 7 # block all other traffic iptables -A INPUT -j DROP And here are some firewall log lines: Dec 6 11:11:57 router kernel: [8725820.003323] iptables denied: IN=ppp0 OUT= MAC= SRC=192.168.1.81 DST=192.168.1.3 LEN=60 TOS=0x00 PREC=0x00 TTL=255 ID=62174 PROTO=UDP SPT=61910 DPT=53 LEN=40 Dec 6 11:12:29 router kernel: [8725852.035826] iptables denied: IN=ppp0 OUT= MAC= SRC=192.168.1.81 DST=224.0.0.1 LEN=44 TOS=0x00 PREC=0x00 TTL=1 ID=15344 PROTO=UDP SPT=56329 DPT=8612 LEN=24 Dec 6 11:12:36 router kernel: [8725859.121606] iptables denied: IN=ppp0 OUT= MAC= SRC=192.168.1.81 DST=224.0.0.1 LEN=44 TOS=0x00 PREC=0x00 TTL=1 ID=11767 PROTO=UDP SPT=63962 DPT=8612 LEN=24 Dec 6 11:12:44 router kernel: [8725866.203656] iptables denied: IN=ppp0 OUT= MAC= SRC=192.168.1.81 DST=224.0.0.1 LEN=44 TOS=0x00 PREC=0x00 TTL=1 ID=11679 PROTO=UDP SPT=57101 DPT=8612 LEN=24 Dec 6 11:12:51 router kernel: [8725873.285979] iptables denied: IN=ppp0 OUT= MAC= SRC=192.168.1.81 DST=224.0.0.1 LEN=44 TOS=0x00 PREC=0x00 TTL=1 ID=39165 PROTO=UDP SPT=62625 DPT=8612 LEN=24 I’m pretty sure that the problem should be related with iptables, but after trying a lot of different confs, I was unable to find the right one. Any help will be greetly appreciated ;). Kind regards, Simon. EDIT: This is my route table: default 62.43.193.33.st 0.0.0.0 UG 100 0 0 eth0 62.43.193.32 * 255.255.255.224 U 0 0 0 eth0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth2 192.168.1.81 * 255.255.255.255 UH 0 0 0 ppp0

  Read the article

1