How do i Change a Dammage Disk in a Raid 5

Posted by Egakagoc2xI on Server Fault See other posts from Server Fault or by Egakagoc2xI
Published on 2010-05-26T19:00:41Z Indexed on 2010/05/26 19:03 UTC
Read the original article Hit count: 201

Filed under:

raid

|

raid5

Hi,

I have a 4 drives Raid 5 Server, which one of them is dammage, all drivers are hot plugged. My Question is, I Want to replace the dammage with a new one, Do I have to shutdown the server or just change the hard drives with the server on a it'll rebuild the every or there is a procedure to follow? My Server is a HP.

Regards.

© Server Fault or respective owner

Related posts about raid

Booting from integrated RAID controller when another RAID controller is installed in a PCIe slot

as seen on Server Fault - Search for 'Server Fault'
I have a GA MA785GT UD3H motherboard with Windows Server 2008 R2 installed on a RAID1 using the on-board RAID controller. I have now installed a RocketRaid 2680 controller and set up a RAID5 for all my data to be stored on. Unfortunately I now cannot boot from the RAID1 anymore, the PC is trying… >>> More
Onboard RAID vs Software RAID

as seen on Server Fault - Search for 'Server Fault'
My motherboard, an Asus M4a79t Deluxe, advertises RAID 0/1/5 capabilities. My limited understanding is that onboard RAID is better than software RAID. Is this necessarily true? Is an onboard RAID controller closer in performance to a software controller or a dedicated hardware controller? >>> More
RAID-1 and regular drive removal (using RAID-1 as a backup measure)

as seen on Super User - Search for 'Super User'
Is using mdadm's RAID-1 of 2 partitions (one on laptop's internal HDD, one on external HDD) a good idea. I want the system to work as RAID-1 if both drives are present, work as regular volume (degradad RAID-1) if external HDD is unplugged and quickly resync when I plug external HDD again. Questions: Is… >>> More
Explain difference in SQLIO numbers for RAID 0 versus RAID 5 over 6 disks

as seen on Stack Overflow - Search for 'Stack Overflow'
When using the SQLIO benchmark tool on a 4-core Dell server with 6 15k 450GB (fast) drives, RAID 0, we found the max throughput was 2MB per second. But when configured as RAID 5, we get 30 MB per second. It seems that the RAID controller, Dell Perc 5i integrated controller, is maxing out the… >>> More
RAID 5 RECONSTRUCT with RAID Reconstructor

as seen on Server Fault - Search for 'Server Fault'
I have Dell Poweredge server 2600 with Raid 5 in 3 hard drive Scsi 36gb each, it was fail to boot sinc the third drive is offline. I attached Sata card adapter to Sata hard drive and install OS SERVER 2003 to it, downloaded drivers for Raid and everything goes fine when I use recovery data software… >>> More

Related posts about raid5

Server 2008 RAID5 resynching

as seen on Server Fault - Search for 'Server Fault'
I built a W2K8 R2 server last weekend, and built a R5 array using Disk Management, 5x 1TB drives. For the next 60 hours the status said 'Resynching (X%)' as it built the array. during this time i did read and write to the drive (slowly) and once the rebuild was complete speeds were quite fast. I… >>> More
HP DL380 RAID5 Mistake

as seen on Server Fault - Search for 'Server Fault'
I had drives fail in both logical drives on a server. When I replaced failed 146GB drive in Raid 5 array with four (4) 146GB drives. On reboot the Smart Array controller asked if I wanted to accept data loss. Guess mistake to choose yes. Can't seem to find a way to get system to repair RAID5 but… >>> More
How to stop RAID5 array while it is shown to be busy?

as seen on Super User - Search for 'Super User'
I have a raid5 array and need to stop it, but while trying to stop it getting error. # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sde1[3](F) sdc1[4](F) sdf1[2] sdd1[1] 2120320 blocks level 5, 32k chunk, algorithm… >>> More
How can I create a 4TB partition on my software RAID5 device?

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
I have set up a RAID5 device with three 2TB hard drives using mdadm. The device was successfully created, but I cannot seem to create a partition on the device. When I try to make an ext3 or ext4 partition via Disk Utility, I get the following error Error creating partition: helper exited with exit… >>> More
Installing raid 5 on a pre-installed ubuntu server. 12.04

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
I have a ubuntu server with samba already set up and installed with a 1tb hdd. I am wanting to now install 3 more 1tb drives and create a raid array using raid 5. I have found a lot of documentation about installing raid when installing and setting up ubuntu server for the first time. However, I… >>> More