-
as seen on Pro Webmasters
- Search for 'Pro Webmasters'
This is my scenario:
I have a vps with two domains (example1.com, example2.com). When I started with this vps I set example1.com as primary domain and the nameserver were configured with the pattern ns1.example.com, ns2.example1.com. The domains were brought in name.com.
Across the time, I usually…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
I bought vps on santrex.net but can't receive any reply from support. My Problem: I have 5 ip but it pings only 1!!! I can't setup DNS because I need 2 ip minimum .
Could you help me to activate other my IPs?
root@spnova:~# ifconfig
eth0 Link encap:Ethernet HWaddr aa:00:b9:4f:19:01
…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Hi guys!
I'm new to VPS managing and I need to chose which OS to install on my VPS. I have the following alternatives:
CentOS 5.2
Ubuntu 9.10
Ubuntu Server edition 8.10
Debian 5.0 Lenny
Debian 4.0 Etch
Gentoo Minimal 10.0
I tried to install couple of them, I've also installed Webmin and doesn't…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
I attempted to open up a port on my VPS, but I can't connect to my website after opening up that port. Below are the commands I issued to open the port. I didn't get an error or anything after setting this up. I just can't connect to my website after doing this.
[root@vps ~]# iptables -F
[root@vps…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Hi,
i created a vps on vps.net and installed CentOS 5.4 x64 LAMP , i choosed the root password and the server start running, i added my domain name in the vps domain section, also i added the two name servers on where i bought the domain name.
the problem is that i still can't access the domain…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Hello, i have some troubles with setting up a nameserver in PLESK for months now. I have tried all possible scenario's but i can not get this to work.
I am really in need for some help, and if you can i will really appreciate it.
Basically what i want is to just set up a nameserver in PLESK. I have…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Hello i have a nameserver with a primary domain configured. Now i added a second domain, I have set NS records of the second domain to use the first domain, but i get some strange error.
When i do the nameserver check at SIDN, for domains in the netherlands, i sais everything is right configured:
Errors=0…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Up until now, I was pretty confident that it was pretty much impossible to list all the domains handled by a nameserver.
But apparently, there exists a couple of websites on the Internet that are able to list all the domains registered in a namerserver.
For example:
http://www.gwebtools.com/ns-spy/udns1…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
I'm trying to change nameservers for some of my domains at GoDaddy, but I occasionally run into "Nameserver not registered" problems, and then I'm not allowed to set the nameservers. Here are the cases I've tried, and I still don't understand what it takes to have a registered nameserver.
With ns1…
>>> More
-
as seen on Server Fault
- Search for 'Server Fault'
Hello, i have a dedicated with a primary ip and domain name. I added nameserver settings for this domain, and mx records.
n1.mydomain.com
ns2.mydomain.com
etc.
Now i want to add more domain with websites to my server. Now what is the best way to do this.
Should i add the domain, and use the mydomain…
>>> More
