What am I doing wrong with this cat 6 patch panel wiring?

Posted by Max Hodges on Server Fault See other posts from Server Fault or by Max Hodges
Published on 2013-04-17T17:23:25Z Indexed on 2014/05/29 3:31 UTC
Read the original article Hit count: 528

Filed under:

lan

|

wiring

|

cable

|

cat

top number is transmitter bottom number is remote terminator

12345678
36145278

is this because I could be mixing T568A and T568B wiring? how do I know if my patch cord is A or B? Do I just look at the plug and match it up with the diagram on the back of the panel somehow?

plug wired patch panel

EDIT I read that 36145278 indicates a cross over cable, but I'm not trying to make a cross over. Where did I go wrong? I'm guessing the cable plug is T568A but I wired it to the panel using T568B. So I need to redo it as T568A. But in the future how do I know if I cable is A or B?

Cheers!

© Server Fault or respective owner

Related posts about lan

Which LAN card / module combinations proven to work with Wake on LAN

as seen on Ask Ubuntu - Search for 'Ask Ubuntu'
I've got a 12.04 headless server that I've been trying to get to work with wake-on-lan. The card is Marvel 88E8053 using the sky2 module. Although WOL is enabled in BIOS and ethtool shows the card as WOL enabled, it refuses to wake when I send the magic packet. I have verified that the packet is being… >>> More
How does cross domain authentication work in a firewalled environment?

as seen on Server Fault - Search for 'Server Fault'
This is a simplification and the names have been changed to protect the innocent. The assets: Active Directory Domains corp.lan saas.lan User accounts user01@corp.lan user02@corp.lan Servers dc.corp.lan (domain controller) dc.saas.lan (domain controller) server.saas.lan A one way trust exists… >>> More
Setting up Lan within a Lan

as seen on Server Fault - Search for 'Server Fault'
How unreasonable would it be to setup a small LAN within an existing LAN? I'm setting up a series of video surveillance servers and a number of IP cameras in a client's location and cannot have my equipment on the same network as their local machines. My network is essentially self-contained and… >>> More
OpenVPN Bridge LAN-to-LAN Configuration?

as seen on Super User - Search for 'Super User'
I'm trying to configure an OpenVPN bridge LAN-to-LAN setup. Currently, I have the OpenVPN bridge Server/Client setup up running. On the server-side my br-lan interface has tap0, eth0, and wlan0 in the bridge group. On the client-side the br-lan interface has eth0 and wlan0 in the bridge group,… >>> More
Cisco ASA (Client VPN) to LAN - through second VPN to second LAN

as seen on Server Fault - Search for 'Server Fault'
We have 2 site that is linked by an IPSEC VPN to remote Cisco ASAs: Site 1 1.5Mb T1 Connection Cisco(1) 2841 Site 2 1.5Mb T1 Connection Cisco 2841 In addition: Site 1 has a 2nd WAN 3Mb bonded T1 Connection Cisco 5510 that connects to same LAN as Cisco(1) 2841. Basically, Remote Access (VPN)… >>> More

Related posts about wiring

Motherboard Wiring

as seen on Super User - Search for 'Super User'
HI All, I bought a new case to put a motherboard in. Everything fits, I have done this before, but not in a long time! The case has wires for - Power SW - Reset SW - Power LED - HDD LED On the motherboard (ASUS M2NPV-VM) it is clearly labeled where these go, but I cannot remember where the black… >>> More
Home CAT6 wiring: CMR vs CMP?

as seen on Super User - Search for 'Super User'
I'm planning on wiring my house with CAT6 cable. I'm finding a large jump in price between CMR and CMP cabling, and I'm confused by what counts as a 'plenum' and what does not. As I'm wiring my house, I'm planning on going through interior (hollow) walls, and through the attic and crawlspace to… >>> More
Using pre-made patch cables on a punch down block?

as seen on Server Fault - Search for 'Server Fault'
I need to add a 24 port switch to my wiring closet. In the (distant) past, I usually just punched each port of the switch to a 110 block on the wall (using hand-made cables), and cross connect between that and the 110 block that has the runs to each workstation. To save time, I'm thinking of buying… >>> More
Motherboard wiring

as seen on Server Fault - Search for 'Server Fault'
I am putting a new motherboard in a chenbro chasis and I dont get how to plugin the wires for powerSW resetSW, etc. It is a SuperMicro P4DP6 motherboard. ** I cant post an image yet, but here is a long to the spot on the mobo where this goes: http://andrewslack.info/mobo.png The powerSW lead is… >>> More
Junit: Test Spring (auto)wiring with reflection?

as seen on Stack Overflow - Search for 'Stack Overflow'
Hi, Is it possible to JUnit test if wiring by Spring is succesfully? I would like to do this by reflection. Like: get all beans with id *Controller and test if the fields *services are not null? Thank you! >>> More