Search Results

Search found 10 results on 1 pages for 'db9'.

Page 1/1 | 1 

  • USB TO DB9 Adapter

    - by Ioudas
    I have a USB-to-DB9 adapter, no FCC serial visible anywhere, that I need drivers for. I can't seem to get any relevant info searching on Google. Does anyone have any good ideas where I might be able to get a lead on some drivers? I'll even upload a picture of it.

    Read the article

  • What does opening a serial port do?

    - by reve_etrange
    What does opening the standard PC serial port do, in electrical terms (i.e. what voltages on which pins)? For example, the ancient VB6 program which controls an apparatus I am tasked with maintaining toggles .PortOpen to control some TTL. The connection only used 2 pins (bad solders fell apart), so which pins do I solder to? The only labels / documentation refer to pins 7 and 9, saying 0V and 5V parenthetically, but does .PortOpen really just put 5V between RI and RTS?. As a post script, this isn't the weirdest thing about the set up. The TTL I referred to above also connects to an instrument via a BNC to DB9 (!), with only 1 pin used. I guess there was an assumption about a common ground, since the BNC shielding isn't connected to the GND pin? The connection is to the instrument's 'foot pedal' pin, it was a way to remotely trigger the device. Update According to this page, the DTR and RTS pins can go high when the port is opened. If they were so configured, they will subsequently go low when the port is closed. If DTR and RTS are not enabled, opening the port should set both to low (and keep them low).

    Read the article

  • Does a USB to RJ-45 console cable exist?

    - by Carl Flippin
    I am aware of the RJ-45 to DB9 adapter commonly used on cisco routers to access console. I am aware of the USB to DB9 adapters to allow laptops without serial to get a serial port. I am looking for a USB to RJ-45 adapter so I don't have to chain two adapters together. I have searched everywhere but even the pre-packaged solutions seem to have the two adapters chained together. Does such a thing exist? If it doesn't is there some technical reason it cannot? It seems like a manufacturer would just have to wire the DB9 end of the USB adapter differently and it would work just fine plugged straight into the console port of the router.

    Read the article

  • Connecting a USB laptop to a RJ45 serial port

    - by Jon
    We are about to get our first managed switch at work (Procurve 2520G-24-PoE), and this lowly programmer gets to put on his admin hat and try to configure it. The switch has an RJ45 serial port for console access. My laptop has USB ports but no serial port. In fact, there isn't a single computer in the office with a serial port. I've seen USB-to-DB9 adapters, but I need to go from USB to RJ45 (serial). How would I go about accomplishing this? Do I need two adapters? Will USB-to-DB9 and then DB9-to-RJ45 work? Thanks in advance.

    Read the article

  • Snow Leopard Compatible Drivers for Moschip MCS7720 USB-to-Serial Controller

    - by Kristopher Johnson
    We are using Cables Unlimited USB-2925 USB-to-Dual-DB9 serial cables, which use the Moschip MCS7720 controller. We have downloaded the newest driver from http://www.moschip.com/mcs7720.php, but that driver was last updated in 2005. It does not seem to be working with Macs running OS X 10.6 Snow Leopard. Does anyone know of any updates for this driver, or are there any ways to get the driver to work with Snow Leopard?

    Read the article

  • Snow Leopard Compatible Drivers for Moschip MCS7720 USB-to-Serial Controller

    - by Kristopher Johnson
    We are using Cables Unlimited USB-2925 USB-to-Dual-DB9 serial cables, which use the Moschip MCS7720 controller. We have downloaded the newest driver from http://www.moschip.com/mcs7720.php, but that driver was last updated in 2005. It does not seem to be working with Macs running OS X 10.6 Snow Leopard. We have sent emails to the support addresses for both Cables Unlimited and Moschip. Cables Unlimited says they are checking with Moschip. No responses from Moschip yet. Does anyone know of any updates for this driver, or are there any ways to get the driver to work with Snow Leopard?

    Read the article

  • Laptop with internal serial port in 2009 (and 2010)

    - by Vincent Demeester
    Are there any computer vendors (like Dell, Lenovo, or..) that still sell laptops with an internal serial port? We are using several modem and other kind of box at work that have to be used (and/or programmed) with serial port (RS232, DB9, ..). We tried many usb/pcmcia serial adapter which run fine when used to load programs on the boxes but not with modems. The protocol behind the RTC connection (with modem) need timer we are not able to reach when using an adapter (maybe until we find a very good adapter), and that leads to my question..

    Read the article

  • How do I connect to the serial console port os a Sunfire 280R?

    - by DrStalker
    We have a Sunfire 280R (old SPARC/Solaris server) that is refusing to come up after being relocated. We're trying to connect to the serial console port, but all we get is random gibberish on the screen. We've tried both connecting with a DB25DB9 adapter and using a DB-25-RJ45 adapter with a cisco RJ45-DB9 adapter to a windows laptop. We're configuring the laptop to 9600 baud, 8 bit, 1 stop bit, no parity. We've tried both no flow control and Xon/Xoff. We get the same results hooking up to the serial port on a working SPARC server, so it's probably something in our setup rather than a fault with the server. How do we get access to to serial console so we can work out what is stopping this box from getting to the network? Is there a special sun adapter we need to get/make to get the serial link working?

    Read the article

  • Text on Cisco ASA console is garbled/missing letters

    - by Some Linux Nerd
    I've actually looked up a number of solutions for this problem and none of them work. There's this Cisco ASA 5505 that I'd like to use, that outputs mildly garbled text with missing characters. I did some googling and found that the most likely problem is a bad baud rate, so I tried all the baud rates, 7N1, 8N2... basically every possibility minicom had. Then I figured (since I can type ok, just not read) that if I factory reset it that it would fix whatever is set wrong with the terminal. That didn't work either. This usb-db9 adapter and console cable work fine on the catalyst switch in our office. My serial settings are 9600 8N1 with no flow control. Anyone know how to fix this? I have an example of the text on pastebin: http://pastebin.com/MAJF0mVU - it's just lots of "Dfaut cnfiuraionfil cotais 1enty." instead of "Default configuration blah blah"

    Read the article

1