Search Results

Search found 444 results on 18 pages for 'gordon bell'.

Page 1/18 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Terminal Bell Doesn't Work

    - by JoBu1324
    I'd like to get the terminal bell playing through my speakers, but so far I haven't had any luck. I've tried the suggestions in this question as well as a number of other sources, but I haven't had any luck. I've also gone the route of un-blacklisting pcspkr in modprobe, but that only works for the beep command, not the terminal bell, echo -e '\a', ping -a, etc. I don't have a "PC Beep" option in alsamixer

    Read the article

  • setting visual bell to flash in iTerm

    - by blackwing
    Hi, I am using iTerm on OSX (leopard) to ssh to a linux machine. I run screen on the dev machine to save my work between sessions. I am not a big fan of audio bell and I don't like screen's default 'Wuff Wuff' bell (or any other little message shown at bottom of the page). What I like though is to have flash (foreground and blackground colors swapped for a fraction of a second) as my visual bell. I used to use PuTTY and it is as simple as ticking a checkbox but I can't find such an option in iTerm. My question is how can I set my visual bell to flash? The ideal answer would work with iTerm on local computer, iTerm sshed to a linux server, and iTerm sshed to a linux server and ran screen.

    Read the article

  • per terminal bell in ubuntu classic

    - by Owen Maresh
    I'm using natty. I'm using classic. I use raw xterms (the latest build, 270, in fact). I've done xset b 100 pactl upload-sample /usr/share/sounds/ubuntu/stereo/message.ogg bell.ogg But I want something more fine grained than this: I want to say "if the bell originated in some particular pseudoterminal make a particular sound, but if it originated in some other particular pseudoterminal, generate some other sound"

    Read the article

  • packhard bell dot s netbook ubuntu 12.10

    - by Kermit
    sorry im absolutly linux beginner.... i bought a packhard bell netbook dots with Limpus.did not get along with limpus so wanted to install ubuntu. netbook: 2 GB RAM intel Atom N2600, intel graphics Media Accelerator 3600 I over installled ubuntu 12.10 (desktop version) like in the instruction (isofile over USB). Installation went fine. No problems. when starting after installation alot of text is coming.....starting xyz....with alot of okays at the end of line but nothing happends: ends with #Starting CPU interrups balancing daemon, stopping anachronics cron and blinking cursor... was reading in this forum, tried to do some things like #recoverymode# and nomodeset... but did not work or where do i get this graphic drivers from. Packard bell just offers windows drivers.and how do i install them? maybe its a completely diffrent cause for this? Thanks alot

    Read the article

  • 11.10 desktop alerts (volume change and terminal bell) stopped working but all other audio still works

    - by FlabbergastedPickle
    All, My sound works just fine in 11.10 64-bit install on HP dm1-4050 Sandy Bridge notebook (e.g. audio works in Banshee, flash, games, browser, Thunderbird email notification, etc.), but the core desktop notifications (e.g. pressing a tab in a terminal where there is more than one option should trigger a terminal bell, or changing volume using volume keys should be accompanied with the supporting "quack" that the volume app makes) do not work. I've intentionally disabled login sound as explained here on ask ubuntu but even enabling it back makes no difference. These notifications did work before just fine and I am not sure when did the actually stop working but it must've been fairly recently. Only things I did were trying to install some ppa edge xorg drivers for my intel card (a separate issue) but also reverted them all with ppa-purge once I discovered they did not improve anything. Other thing I did was check volume settings with alsamixer and did alsactl store for the soundcard after I did some experimenting with volume settings for PCM (on my laptop PCM at 100% crackles so I had to lower it and make pulseaudio ignore its setting as per ask ubuntu's page). That said, neither of these should have any bearing on the said notifications since the volume is up and they clearly work everywhere else but the core desktop events. The system ready drum sound when Ubuntu boots and user reaches the login screen also does not work. The guest login behaves exactly same as mine. Audio works (including the login sound since I've not disabled it for the guest account), but no quacks when changing the volume or terminal bell sounds... I've tried copying ubuntu sounds to /usr/share/sounds/ as suggested on ask ubuntu and that did not work. I also tried using dconf-editor to check sound theme settings and tried both freedesktop (which is what it was set to) and ubuntu, as suggested on ask ubuntu. This did not work either. I tried purging the ~/.pulse folder and the /tmp/*pulse* entries, rebooting and restarting pulseaudio with -D flag. While audio came back on and behaved just fine in all aspects (e.g. one can adjust volume levels, play music, games, in-browser sound stuff, and other app alerts) except for the system ready drum sound (at the login screen), and any system event (terminal bell and volume change quack sound). It is interesting that the quack sound works inside system settings-sound when adjusting levels there, but it does not when volume is changed via top bar's volume settings... I do recall that at one point yesterday when I was restarting pulseaudio the quacks that accompany volume change did start working but I have no idea what caused that. This was also when I first realized those alerts were not working. After rebooting it was again gone. I did compile my own 3.0.14-rt31 kernel a little while ago as instructed on one of the wiki's for the 11.10 rt kernel. Everything works as before except for the said sound alerts. I am not sure if this began happening since I started using the rt kernel though and yesterday's momentary ability to hear those quacks while changing the volume make me believe that the kernel is not one responsible for this problem. One more thing I can think of is that I used alsoft-conf tool to configure buffering on the OpenAL (due to TA Spring's choppy audio) and changed in there default audio device to ALSA. I also tried reverting it to Pulseaudio as the only allowed output but the bottom part of the Backend tab always reverts to ALSA even when I select Pulseaudio. The pulseaudio does remain as the only active choice on top. This, however, once again does not make any sense in terms of preventing desktop audio alerts when everything else including OpenAL games plays sound just fine... So, there you have it, as verbose as I could make it :-). I tried all I could find on this issue and had no luck so far... Any ideas?

    Read the article

  • Packard Bell TK11 Wifi not working (Ubuntu 12.10)

    - by Ingmar
    Hardware: Packard Bell EasyNote TK11BZ, BIOS version 1.15 Broadcom BCM43227 802.11 b/n/g Problem: Everything works as it should, except the wireless connection. The Wifi device is enabled in the "Additional Drivers" section of Software Sources, but does not even show up in the network manager drop-down. sudo lshw -C network: *-network UNCLAIMED description: Network controller product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0100000-f0103fff

    Read the article

  • Silverlight TV with Myself, John Papa, Shawn Wildermuth and Ward Bell

    - by dwahlin
    I had the chance to go on a live episode of Channel 9 while at DevConnections and had a lot of fun chatting about various Silverlight topics and answering some fairly unique questions posted on Twitter.  Here’s more info on the episode from John Papa’s blog: John interviews a panel of 3 well known Silverlight leaders including Shawn Wildermuth, Dan Wahlin, and Ward Bell at the Silverlight 4 launch event. The guest panel answers questions sent in from Twitter about the features in Silverlight 4, thoughts on MVVM, and the panel members' experiences developing Silverlight. This is a great chance to hear from some of the leading Silverlight minds. These guys are all experts at building business applications with Silverlight. Relevant links: John's Blog and on Twitter (@john_papa) Shawn's Blog and on Twitter (@shawnwildermuth) Dan's Blog and on Twitter (@danwahlin) Ward's Blog and on Twitter (@wardbell) Silverlight Training Course on Channel 9 Follow us on Twitter @SilverlightTV or on the web at http://silverlight.tv You can see the episode online by clicking the image below:

    Read the article

  • Packard Bell EasyNote MZ35 freezes when AC unplugged and wireless on

    - by Sense Hofstede
    I would like to ask for some help debugging an irritating problem I'm having with my Packard Bell EasyNote MZ35 and Ubuntu 10.10. Always when the laptop is connected to a wireless network and the AC power lead is unplugged—so it's running on battery power—the system freezes. The screen turns black and shows the error GLib-WARNING **: getpwuid_r(): failed due to unknown user id (0), although this error is completely unrelated to the actual problem. Previous searches on the internet indicate that this error is unrelated to the bug I'm experiencing. It is suggested that Ubuntu tries to hibernate or suspend and that you're seeing the black screen running 'behind' the X server. That would explain the fact that curiously you still see—but cannot move—the mouse cursor. I've already set all the values of the GConf keys in /apps/gnome-power-manager/actions/ to 'nothing', disabled all power management actions I could find, but it didn't solve the problem. It is important to note that the freeze doesn't happen immediately after you unplug the AC power lead. The icon in the notification area may have changed already, but the freeze only occurs when the Notify OSD bubble appears that tells you how many time is left with your battery. Does anyone here have a clue about this problem? A workaround or the cause? If anyone could help me with disabling possible suspend/hibernate behaviour that might be related to this issue, that would be appreciated too. This issue has been reported as bug #666852.

    Read the article

  • Packard Bell Easynote NJ65 not saving gamma Setup.

    - by Pablo Gomez
    Hi. There seems to be a issue with the Easynote range of PB laptops. Since Ubuntu 10.10 does not use a Xorg.conf file to save your gamma / resolution /brightness setting, everytime I turn on my laptop I have to open up a terminal window and use the x-gamma command to set it up to my personal preference. Is there a way to create a configuration file which can save that into the system everytime I load up the OS? When I used to have a Compaq Presario (an F564LA with integrated nVIDIA graphics), I could save a config. file into the system which loaded up everything on startup To those who don't know the spec's for a NJ65 laptop, I'll provide them Processor: Intel® Pentium Dual Core @ 2.2 GHZ Video: Integrated Intel® GMA 4500MHD graphics HDD: 320GB SATA RAM: 2GB DDR2

    Read the article

  • How to sound audible bell from crontab

    - by user1526251
    The command line: /bin/echo -e "\007" in bash will ring the bell. With the line: /bin/echo -e "\007" in my crontab I expected the bell to ring every minute, but it's silent. I know crontab is working because the line: /bin/touch $HOME/jkjkjk updates the file jkjkjk every minute as it should. I found a posting some years ago suggesting that standard output should be directed to /dev/tty1 in crontab. But the line: /bin/echo "\007" /dev/tty1 Still fails. What to try next?

    Read the article

  • How can I set a per terminal bell with xterms?

    - by Owen Maresh
    I'm using natty. I'm using classic. I use raw xterms (the latest build, 270, in fact). I've done xset b 100 pactl upload-sample /usr/share/sounds/ubuntu/stereo/message.ogg bell.ogg But I want something more fine grained than this: I want to say "if the bell originated in some particular pseudoterminal make a particular sound, but if it originated in some other particular pseudoterminal, generate some other sound"

    Read the article

  • Windows 8 Pro Remote Desktop issue

    - by Mike C.
    I have a weird issue here. I'm running Windows 8 Pro. The client computer is also running Windows 8 Pro. Remote Desktop works when I'm in the same network. I tried connecting using my external IP Address and my DynDNS account, neither works. I disabled Windows Firewall and setup DMZ for my computer on the router, still can't get remote desktop to work. I verified www.canyouseeme.org, port 3389 is open, which is obvious since I'm running DMZ! My ISP, Bell Canada (modem/router: Sagemcom F@st 2864), blocks port 80 and 25, but I don't need those for RDP, do I? The funny thing is RDP rejects the connection instantaneously for my IP or DynDNS while it takes a while for another address. Thank you, Michael

    Read the article

  • Ask How-To Geek: Fixing the Windows Boot Record, Sharing Mac Folders with Windows, and Reviving the Outlook Reminder Bell

    - by Jason Fitzpatrick
    You’ve got questions and we’ve got answers. Today we look at how to boot into Windows after uninstalling Linux, sharing folders between a Mac and a Windows computer, and how to reinstate the missing Outlook reminder bell. Once a week we dip into our mailbag and help readers solve their problems, sharing the useful solutions with you I the process. Read on to see our fixes for this week’s reader dilemmas.How To Make a Youtube Video Into an Animated GIFHTG Explains: What Are Character Encodings and How Do They Differ?How To Make Disposable Sleeves for Your In-Ear Monitors

    Read the article

  • Les 8 gestes de Windows 8 à connaitre sur le bout des doigts, pour l'utiliser en version tactile. Par Gordon Fowler

    Les 8 gestes de Windows 8 A connaitre sur le bout des doigts pour l'utiliser en version tactile Windows 8. Ses nouveautés. Son Start Screen. Son optimisation pour le tactile? Et ses gestes pas du tout instinctifs dans une utilisation sur tablette si l'on essaye de s'y prendre comme sur Android ou iOS. Je dois vous avouer que je ne suis pas le plus brillant des testeurs. Je veux dire par là qu'il peut m'arriver ? sous les regards moqueurs de certains de mes confrères ? de mettre plusieurs minutes à configurer un compte BBM ou à me demander ou peut bien être ce satané bouton on/off. L'avantage d'être ainsi "limité", c'est que je peux aider ceux qui comme moi ...

    Read the article

  • Cannot ping host stale ARP cache?

    - by gkchicago
    I am having a strange issue with a Debian (Lenny/Linux 2.6.26-2-amd64) that has been driving me nuts. On some machines within my network I can ping the host in question just fine, other times I have to manually hard-code the ARP ethernet address for the IP in order to establish connectivity. I've finally worked it down to somehow involving ARP. I just found how to fix it in a way that made it work but I'm looking for help explaining this issue and also I don't trust my fix to be permanent.. My thought process has been the following but I just can't make any sense out of it: Could it be the card? (Intel 82555 rev 4) Could it be because there are two network cards? (Default route is eth0) Could it be because of the network aliases? Lenny? AMD x86_64? Argh.. Thank you for any insight you might have // Ping doesn't go thru [gordon@ubuntu ~]$ ping 192.168.135.101 PING 192.168.135.101 (192.168.135.101) 56(84) bytes of data. --- 192.168.135.101 ping statistics --- 4 packets transmitted, 0 received, 100% packet loss, time 3014ms // Here's the ARP Table, sometimes the .151 address is good, sometimes it // also matches the Gateways MAC like .101 is doing right here. [gordon@ubuntu ~]$ cat /proc/net/arp IP address HW type Flags HW address Mask Device 192.168.135.15 0x1 0x2 00:0B:DB:2B:24:89 * eth0 192.168.135.151 0x1 0x2 00:0B:6A:3A:30:A6 * eth0 192.168.135.1 0x1 0x2 00:1A:A2:2D:2A:04 * eth0 192.168.135.101 0x1 0x2 00:1A:A2:2D:2A:04 * eth0 // Drop the bad arp table listing and set it manually based on /sbin/ifconfig [gordon@ubuntu ~]$ sudo arp -d 192.168.135.101 [gordon@ubuntu ~]$ sudo arp -s 192.168.135.101 00:0B:6A:3A:30:A6 // Ping starts going thru..?!? [gordon@ubuntu ~]$ ping 192.168.135.101 PING 192.168.135.101 (192.168.135.101) 56(84) bytes of data. 64 bytes from 192.168.135.101: icmp_seq=1 ttl=64 time=15.8 ms 64 bytes from 192.168.135.101: icmp_seq=2 ttl=64 time=15.9 ms 64 bytes from 192.168.135.101: icmp_seq=3 ttl=64 time=16.0 ms 64 bytes from 192.168.135.101: icmp_seq=4 ttl=64 time=15.9 ms --- 192.168.135.101 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3012ms rtt min/avg/max/mdev = 15.836/15.943/16.064/0.121 ms The following is my network config on this. gordon@db01:~$ /sbin/ifconfig eth0 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.151 Bcast:192.168.135.255 Mask:255.255.255.0 inet6 addr: fe80::20b:6aff:fe3a:30a6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15476725 errors:0 dropped:0 overruns:0 frame:0 TX packets:10030036 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18565307359 (17.2 GiB) TX bytes:3412098075 (3.1 GiB) eth0:0 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.150 Bcast:192.168.135.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0:1 Link encap:Ethernet HWaddr 00:0b:6a:3a:30:a6 inet addr:192.168.135.101 Bcast:192.168.135.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth1 Link encap:Ethernet HWaddr 00:e0:81:2a:6e:d0 inet addr:10.10.62.1 Bcast:10.10.62.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:81ff:fe2a:6ed0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10233315 errors:0 dropped:0 overruns:0 frame:0 TX packets:19400286 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1112500658 (1.0 GiB) TX bytes:27952809020 (26.0 GiB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:387 errors:0 dropped:0 overruns:0 frame:0 TX packets:387 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:41314 (40.3 KiB) TX bytes:41314 (40.3 KiB) gordon@db01:~$ sudo mii-tool -v eth0 eth0: negotiated 100baseTx-FD, link ok product info: Intel 82555 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD gordon@db01:~$ sudo route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface localnet * 255.255.255.0 U 0 0 0 eth0 10.10.62.0 * 255.255.255.0 U 0 0 0 eth1 default 192.168.135.1 0.0.0.0 UG 0 0 0 eth0

    Read the article

  • Python 3.2 est disponible avec des librairies standards améliorées

    Python 3.2 est disponible Avec des librairies standards améliorées Mise à jour du 21/02/11 par Gordon Fowler Depuis le gel de la syntaxe de Python, la branche des versions 2.x ne se verra plus ajouter que des corrections de bugs. Les réelles nouveautés, elles, seront intégrées directement dans le branche 3.x. C'est donc avec un certain intérêt que les développeurs verront la sortie de Python 3.2, rendu disponible pendant le week-end. [IMG]http://ftp-developpez.com/gordon-fowler/python-logo.gif[/IMG] Les efforts des équipes de développement de Python ...

    Read the article

  • The Science Behind Technological Moral Panics

    - by Jason Fitzpatrick
    Why do some new technologies cause ripples and reactionary backlash in society but others slip into our daily lives almost entirely uncontested? It turns out there’s a rather specific combination of things the new technology must do to upset the public. At Wired they highlight the work of Genevieve Bell and her studies of how society reacts to new technology: Genevieve Bell believes she’s cracked this puzzle. Bell, director of interaction and experience research at Intel, has long studied how everyday people incorporate new tech into their lives. In a 2011 interview with The Wall Street Journal‘s Tech Europe blog, she outlined an interesting argument: To provoke moral panic, a technology must satisfy three rules. First, it has to change our relationship to time. Then it has to change our relationship to space. And, crucially, it has to change our relationship to one another. Individually, each of these transformations can be unsettling, but if you hit all three? Panic! Why We Freak Out About Some Technologies but Not Others [Wired] How To Play DVDs on Windows 8 6 Start Menu Replacements for Windows 8 What Is the Purpose of the “Do Not Cover This Hole” Hole on Hard Drives?

    Read the article

  • email output of powershell script

    - by Gordon Carlisle
    I found this wonderful script that outputs the status of the current DFS backlog to the powershell console. This works great, but I need the script to email me so I can schedule it to run nightly. I have tried using the Send-MailMessage command, but can't get it to work. Mainly because my powershell skills are very weak. I believe most of the issue revolve around the script using the Write-Host command. While the coloring is nice I would much rather have it email me the results. I also need the solution to be able to specify a mail server since the dfs servers don't have email capability. Any help or tips are welcome and appreciated. Here is the code. $RGroups = Get-WmiObject -Namespace "root\MicrosoftDFS" -Query "SELECT * FROM DfsrReplicationGroupConfig" $ComputerName=$env:ComputerName $Succ=0 $Warn=0 $Err=0 foreach ($Group in $RGroups) { $RGFoldersWMIQ = "SELECT * FROM DfsrReplicatedFolderConfig WHERE ReplicationGroupGUID='" + $Group.ReplicationGroupGUID + "'" $RGFolders = Get-WmiObject -Namespace "root\MicrosoftDFS" -Query $RGFoldersWMIQ $RGConnectionsWMIQ = "SELECT * FROM DfsrConnectionConfig WHERE ReplicationGroupGUID='"+ $Group.ReplicationGroupGUID + "'" $RGConnections = Get-WmiObject -Namespace "root\MicrosoftDFS" -Query $RGConnectionsWMIQ foreach ($Connection in $RGConnections) { $ConnectionName = $Connection.PartnerName.Trim() if ($Connection.Enabled -eq $True) { if (((New-Object System.Net.NetworkInformation.ping).send("$ConnectionName")).Status -eq "Success") { foreach ($Folder in $RGFolders) { $RGName = $Group.ReplicationGroupName $RFName = $Folder.ReplicatedFolderName if ($Connection.Inbound -eq $True) { $SendingMember = $ConnectionName $ReceivingMember = $ComputerName $Direction="inbound" } else { $SendingMember = $ComputerName $ReceivingMember = $ConnectionName $Direction="outbound" } $BLCommand = "dfsrdiag Backlog /RGName:'" + $RGName + "' /RFName:'" + $RFName + "' /SendingMember:" + $SendingMember + " /ReceivingMember:" + $ReceivingMember $Backlog = Invoke-Expression -Command $BLCommand $BackLogFilecount = 0 foreach ($item in $Backlog) { if ($item -ilike "*Backlog File count*") { $BacklogFileCount = [int]$Item.Split(":")[1].Trim() } } if ($BacklogFileCount -eq 0) { $Color="white" $Succ=$Succ+1 } elseif ($BacklogFilecount -lt 10) { $Color="yellow" $Warn=$Warn+1 } else { $Color="red" $Err=$Err+1 } Write-Host "$BacklogFileCount files in backlog $SendingMember->$ReceivingMember for $RGName" -fore $Color } # Closing iterate through all folders } # Closing If replies to ping } # Closing If Connection enabled } # Closing iteration through all connections } # Closing iteration through all groups Write-Host "$Succ successful, $Warn warnings and $Err errors from $($Succ+$Warn+$Err) replications." Thanks, Gordon

    Read the article

  • Synching folders other than the default Ubuntu One folder doesn't seem to work on Windows

    - by Gordon
    I have installed Ubuntu One on two machines - one Windows 7 and one Windows XP. I have added a folder from the computer using the "Add Folder" button on the Windows 7 machine. The Ubuntu One dialog box tells me that file synch is finished and up to date. I now have two problems. If I log on to my Ubuntu One account on the web, I can see what appears to be a LINK to the synched folder - I cannot open the folder and see the contents. This is what I see in the Files page of my Ubuntu one account: ~/Documents/Computing/Test On the second machine, after synching is complete, I see the folder but NOT the contents. The folder is EMPTY. Can anyone provide a solution as to a) what is happening and b) how do I get this folder to synch properly on the other locations?

    Read the article

  • How much should I charge an hour for freelance iOS development?

    - by Tyler Bell
    I am a fairly competent developer who already holds a job developing iOS applications. This job is through the university which I attend. The producer of the apps that I develop is always trying to set me up with some freelance opportunities to get my work out there and to get me some more work/experience. What is a reasonable price to charge (either hourly or per app)? I'd be working by myself, on my own equipment, from start to finish in the design process. Just wondering what a reasonable price was...I've heard up to $30? Thanks

    Read the article

  • Why is a fully transparent pixel still rendered?

    - by Mr Bell
    I am trying to make a pixel shader that achieves an effect similar to this video http://www.youtube.com/watch?v=f1uZvurrhig&feature=related My basic idea is render the scene to a temp render target then Render the previously rendered image with a slight fade on to another temp render target Draw the current scene on top of that Draw the results on to a render target that persists between draws Draw the results on to the screen But I am having problems with the fading portion. If I have my pixel shader return a color with its A component set to 0, shouldn't that basically amount to drawing nothing? (Assuming that sprite batch blend mode is set to AlphaBlend) To test this I have my pixel shader return a transparent red color. Instead of nothing being drawn, it draws a partially transparent red box. I hope that my question makes sense, but if it doesnt please ask me to clarify Here is the drawing code public override void Draw(GameTime gameTime) { GraphicsDevice.SamplerStates[1] = SamplerState.PointWrap; drawImageOnClearedRenderTarget(presentationTarget, tempRenderTarget, fadeEffect); drawImageOnRenderTarget(sceneRenderTarget, tempRenderTarget); drawImageOnClearedRenderTarget(tempRenderTarget, presentationTarget); GraphicsDevice.SetRenderTarget(null); drawImage(backgroundTexture); drawImage(presentationTarget); base.Draw(gameTime); } private void drawImage(Texture2D image, Effect effect = null) { spriteBatch.Begin(0, BlendState.AlphaBlend, SamplerState.PointWrap, null, null, effect); spriteBatch.Draw(image, new Rectangle(0, 0, width, height), Color.White); spriteBatch.End(); } private void drawImageOnRenderTarget(Texture2D image, RenderTarget2D target, Effect effect = null) { GraphicsDevice.SetRenderTarget(target); drawImage(image, effect); } private void drawImageOnClearedRenderTarget(Texture2D image, RenderTarget2D target, Effect effect = null) { GraphicsDevice.SetRenderTarget(target); GraphicsDevice.Clear(Color.Transparent); drawImage(image, effect); } Here is the fade pixel shader sampler TextureSampler : register(s0); float4 PixelShaderFunction(float2 texCoord : TEXCOORD0) : COLOR0 { float4 c = 0; c = tex2D(TextureSampler, texCoord); //c.a = clamp(c.a - 0.05, 0, 1); c.r = 1; c.g = 0; c.b = 0; c.a = 0; return c; } technique Fade { pass Pass1 { PixelShader = compile ps_2_0 PixelShaderFunction(); } }

    Read the article

  • How to set TextureFilter to Point to make example Bloom filter work?

    - by Mr Bell
    I have simple app that renders some particles and now I am trying to apply the bloom shader from the xna samplers ( http://create.msdn.com/en-US/education/catalog/sample/bloom ) to it, but I am running into this exception: "XNA Framework HiDef profile requires TextureFilter to be Point when using texture format Vector4." When the BloomComponent tries to end the sprite batch in the DrawFullscreenQuad method: spriteBatch.Begin(0, BlendState.Opaque, SamplerState.PointWrap, null, null, effect); spriteBatch.Draw(texture, new Rectangle(0, 0, width, height), Color.White); spriteBatch.End(); //<------- Exception thrown here It seems to be related to the pixel shaders that I am using to animate the particle. In a nutshell, I have a texture2d in vector4 format that holds particle positions, and another one for velocities. Here is a snippet from that area: GraphicsDevice.SetRenderTarget(tempRenderTarget); animationEffect.CurrentTechnique = animationEffect.Techniques[technique]; spriteBatch.Begin(SpriteSortMode.Immediate, BlendState.Opaque, SamplerState.PointWrap, DepthStencilState.DepthRead, RasterizerState.CullNone, animationEffect); spriteBatch.Draw(randomValues, new Rectangle(0, 0, width, height), Color.White); spriteBatch.End(); What I comment out the code that calls the particle animation pixel shaders the bloom component runs fine. Is there some state that I need to reset to make the bloom work?

    Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >