Search Results

Search found 10 results on 1 pages for 'hsrp'.

Page 1/1 | 1 

  • Colocation and HSRP setup

    - by WinkyWolly
    My colocation provider has setup HSRP for us and has provided us 2 drops (plugged into 1/1/1 and 1/1/2) from their routers as well as a /29 with 2 HSRP IP's and the rest of the /29 usable for the switch. I know that HSRP should be pretty much plug and play as long as the ports are in the same VLAN. However I'm confused as to how to the IP setup should work. Currently I've assigned port 1/1/1 the full /29 however I think this is incorrect because if I were to unplug it port 1/1/2 wouldn't work as it has no IP assignment. What's the proper way to do this?

    Read the article

  • Confusion about HSRP Groups

    - by Kyle Brandt
    If I have a router that has several LANs on it, and each of these LAN is attached to a second router, do I need to use different HSRP groups for each LAN? With this set up, each virtual gateway will be on a Layer 2 segment. And within a router, no interface will have multiple gateways. So, For example: Router 1: F0/0: ip address 192.168.1.2 255.255.255.0 standby ip 192.168.1.1 F2/0: ip address 192.168.2.2 255.255.255.0 standby ip 192.168.2.1 Router 2: F0/0: ip address 192.168.1.3 255.255.255.0 standby ip 192.168.1.1 F2/0: ip address 192.168.2.3 255.255.255.0 standby ip 192.168.2.1 Will this work, or do I need standby 1 ip 192.168.2.1 on the F2/0 interfaces? Since according to the RFC, the group number of the packet is in the HSRP multicast packets, my guess is that I don't need different groups, and that multiple groups are only needed when they are all on the same Layer 2 segment. However, I haven't been able to find this setup....

    Read the article

  • Cisco Switching Module and HSRP interface Tracking

    - by Kyle Brandt
    When using 4 port switching module where each port is configured to switchport access vlan ##, for HRSP should I track the vlan interface or the FastEthernet interface? interface FastEthernet0/0/0 switchport access vlan 10 interface Vlan10 ip address 12.12.12.1 255.255.255.0 int FastEthernet0/1 ip address 192.168.1.2 255.255.255.0 standyby ip 192.168.128.1 standby track ?? ! FastEthernet 0/0/0 or Vlan 10?

    Read the article

  • cisco 2900xl - SNMP - Get mac address of device connected to an interface

    - by ankit
    Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

    Read the article

  • NIC Teaming HP Server running Win2003

    - by Colm
    Hello everyone. I'm new to server NIC TEaming. I have a HP ProLiant DL360 G4p running Win2003 with 2 NICs , only one is currently active. I'd like to activate the 2nd NIC connected (in a active/passive state) to a 2nd switch with only one IP address and ideally only one mac layer address. The 1st switch is a Cisco 2960G and the 2nd is a Cisco C3560G. There are VLANS, RSTP and PAGP in use already. Can someone give me an idea, in broad terms , of what technology/protocols I should be investigating (HSRP, SLB/TLB Teaming etc.) ? I can provide more info if needed. Thanks, Colm.

    Read the article

  • Dual Home HP Server running Win2003

    - by Colm
    Hello everyone. I'm new to server dual homing. I have a HP ProLiant DL360 G4p running Win2003 with 2 NICs , only one is currently active. I'd like to activate the 2nd NIC connected (in a active/passive state) to a 2nd switch with only one IP address and ideally only one mac layer address. The 1st switch is a Cisco 2960G and the 2nd is a Cisco C3560G. There are VLANS, RSTP and PAGP in use already. Can someone give me an idea, in broad terms , of what technology/protocols I should be investigating (HSRP, SLB Teaming etc.) ? I can provide more info if needed. Thanks, Colm.

    Read the article

  • Configure Cisco Pix 515 with DMZ and no NAT

    - by Rickard
    I hope that someone could shed some light over my situation, as I am fairly new to PIX configurations. I will be getting a new net for my department, which I am going to configure. At my hands, I have a Cisco PIX 515 (not E), a Cisco 2948 switch (and if needed, I can bring up a 2621XM router, but this is my private and not owned by my dept.). The network I will be getting is the following: 10.12.33.0/26 Link net between the ISP routers and my network will be 10.12.32.0/29 where GW is .1 and HSRP roututers are .2 and .3 The ISP has asked me not to NAT the addresses on my side, as they will set it up to give 10.12.33.2 as a one-to-one nat to a public IP. The rest of the IP's will be a many-to-one NAT to another public IP. 10.12.33.2 is supposed to be my server placed on the DMZ, the rest of the IP's will be used for my clients and the AD server (which is currently also acting as a DHCP server in the old network config with another ISP). Now, the question is, how would I best configure this? I mean, am I thinking wrong here, I am expected to put the PIX first from the ISP outlet, then to the switch which will connect my clients. But with the ISP routers being on a different network, how will the firewall forward the packets to the other network, it's a firewall, not a router. I have actually never configured a pix before, and fortunately, this is more like a lab network, not a production network, so if something goes wrong it's not the end of the world, if though annoying. I am not asking for a full configuration from anyone, just some directions, or possibly some links which will give me some hints. Thank you very much!

    Read the article

  • How to know the source of certain TCP traffic on AIX

    - by A.Rashad
    We have two AIX boxes, one for production system and another for testing. both systems are running ATM machine switches, where the ATM device is connected via TCP socket. we had an issue on production system where the machine would power off or get disconnected but the netstat -na | grep <IP of machine > would still mention that the socket is up when simulated that case on the UAT environment, the problem did not happen, where the socket would terminate in 3 to 5 minutes. when sniffed on the traffic between the machine and ATM we found that no traffic takes place on production while there is some sort of heartbeat on UAT. but it is not initiated by the application. $>tcpdump | grep -v "10.2.2.71" | grep -v "HSRP" | grep "10.3.1.30" tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on en6, link-type 1, capture size 96 bytes 09:08:13.323421 IP server073.afs3-callback > 10.3.1.30.impera: . 278204201:278204202(1) ack 3307884029 win 164 09:08:13.335334 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:08:23.425771 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:08:23.425789 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 09:09:13.628985 IP server073.afs3-callback > 10.3.1.30.impera: . 0:1(1) ack 1 win 164 09:09:13.633900 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:09:23.373634 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:09:23.373647 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 while on production, that traffic is not there. we want to know where this traffic is initiated from to implement on production to sense disconnection our comms parameters are: tcp_keepcnt = 2 tcp_keepidle = 100 tcp_keepinit = 150 tcp_keepintvl = 150 tcp_finwait2 = 1200 can anyone help? Editing Question: One point I missed because I was rushing to a meeting. the difference between the Production and UAT in setup is that in Production we have an application called F5 working as load balancer between the ATMs and the AIX box, while it is a direct connection through MPLS in case of UAT. note: we had one MPLS and one GPRS connected ATMs on UAT, and both connections terminated when unplugged in about 4 minutes Edit 2 the no -o tcp_timewait command returns 1 in both Production and UAT

    Read the article

  • How to know the source of certain TCP traffic on AIX

    - by A.Rashad
    We have two AIX boxes, one for production system and another for testing. both systems are running ATM machine switches, where the ATM device is connected via TCP socket. we had an issue on production system where the machine would power off or get disconnected but the netstat -na | grep <IP of machine > would still mention that the socket is up when simulated that case on the UAT environment, the problem did not happen, where the socket would terminate in 3 to 5 minutes. when sniffed on the traffic between the machine and ATM we found that no traffic takes place on production while there is some sort of heartbeat on UAT. but it is not initiated by the application. $>tcpdump | grep -v "10.2.2.71" | grep -v "HSRP" | grep "10.3.1.30" tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on en6, link-type 1, capture size 96 bytes 09:08:13.323421 IP server073.afs3-callback > 10.3.1.30.impera: . 278204201:278204202(1) ack 3307884029 win 164 09:08:13.335334 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:08:23.425771 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:08:23.425789 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 09:09:13.628985 IP server073.afs3-callback > 10.3.1.30.impera: . 0:1(1) ack 1 win 164 09:09:13.633900 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:09:23.373634 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:09:23.373647 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 while on production, that traffic is not there. we want to know where this traffic is initiated from to implement on production to sense disconnection our comms parameters are: tcp_keepcnt = 2 tcp_keepidle = 100 tcp_keepinit = 150 tcp_keepintvl = 150 tcp_finwait2 = 1200 can anyone help?

    Read the article

1