Search Results

Search found 13752 results on 551 pages for 'ip protocol'.

Page 1/551 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• PPTP connection disconnect

  - by Vladimir Franciz S. Blando

  My pptp connection wont stay connected, it will disconnect in less than a minute here are some relevant log entries May 31 13:32:31 localhost NetworkManager[931]: <info> Starting VPN service 'pptp'... May 31 13:32:31 localhost NetworkManager[931]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 15216 May 31 13:32:31 localhost NetworkManager[931]: <info> VPN service 'pptp' appeared; activating connections May 31 13:32:31 localhost NetworkManager[931]: <info> VPN plugin state changed: init (1) May 31 13:32:31 localhost NetworkManager[931]: <info> VPN plugin state changed: starting (3) May 31 13:32:31 localhost NetworkManager[931]: <info> VPN connection 'Dynalabs' (Connect) reply received. May 31 13:32:31 localhost pppd[15221]: Plugin /usr/lib/pppd/2.4.5/nm-pptp-pppd-plugin.so loaded. May 31 13:32:31 localhost pppd[15221]: pppd 2.4.5 started by root, uid 0 May 31 13:32:31 localhost pptp[15224]: nm-pptp-service-15216 log[main:pptp.c:314]: The synchronous pptp option is NOT activated May 31 13:32:31 localhost pppd[15221]: Using interface ppp0 May 31 13:32:31 localhost pppd[15221]: Connect: ppp0 <--> /dev/pts/5 May 31 13:32:31 localhost NetworkManager[931]: SCPlugin-Ifupdown: devices added (path: /sys/devices/virtual/net/ppp0, iface: ppp0) May 31 13:32:31 localhost NetworkManager[931]: SCPlugin-Ifupdown: device added (path: /sys/devices/virtual/net/ppp0, iface: ppp0): no ifupdown configuration found. May 31 13:32:32 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 1 'Start-Control-Connection-Request' May 31 13:32:32 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_disp:pptp_ctrl.c:739]: Received Start Control Connection Reply May 31 13:32:32 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_disp:pptp_ctrl.c:773]: Client connection established. May 31 13:32:33 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 7 'Outgoing-Call-Request' May 31 13:32:34 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_disp:pptp_ctrl.c:858]: Received Outgoing Call Reply. May 31 13:32:34 localhost pptp[15235]: nm-pptp-service-15216 log[ctrlp_disp:pptp_ctrl.c:897]: Outgoing call established (call ID 0, peer's call ID 1536). May 31 13:32:37 localhost pppd[15221]: CHAP authentication succeeded May 31 13:32:37 localhost kernel: [54007.078553] PPP MPPE Compression module registered May 31 13:32:40 localhost pppd[15221]: MPPE 128-bit stateless compression enabled May 31 13:32:42 localhost pppd[15221]: local IP address 10.100.0.52 May 31 13:32:42 localhost pppd[15221]: remote IP address 10.100.0.1 May 31 13:32:42 localhost pppd[15221]: primary DNS address 4.2.2.1 May 31 13:32:42 localhost pppd[15221]: secondary DNS address 255.255.255.255 May 31 13:32:42 localhost NetworkManager[931]: <info> VPN connection 'Dynalabs' (IP Config Get) reply received. May 31 13:32:42 localhost NetworkManager[931]: <info> VPN Gateway: 103.28.219.2 May 31 13:32:42 localhost NetworkManager[931]: <info> Tunnel Device: ppp0 May 31 13:32:42 localhost NetworkManager[931]: <info> Internal IP4 Address: 10.100.0.52 May 31 13:32:42 localhost NetworkManager[931]: <info> Internal IP4 Prefix: 32 May 31 13:32:42 localhost NetworkManager[931]: <info> Internal IP4 Point-to-Point Address: 10.100.0.1 May 31 13:32:42 localhost NetworkManager[931]: <info> Maximum Segment Size (MSS): 0 May 31 13:32:42 localhost NetworkManager[931]: <info> Forbid Default Route: no May 31 13:32:42 localhost NetworkManager[931]: <info> Internal IP4 DNS: 4.2.2.1 May 31 13:32:42 localhost NetworkManager[931]: <info> Internal IP4 DNS: 255.255.255.255 May 31 13:32:42 localhost NetworkManager[931]: <info> DNS Domain: '(none)' May 31 13:32:43 localhost dnsmasq[2127]: exiting on receipt of SIGTERM May 31 13:32:43 localhost NetworkManager[931]: <info> DNS: starting dnsmasq... May 31 13:32:43 localhost NetworkManager[931]: <info> (ppp0): writing resolv.conf to /sbin/resolvconf May 31 13:32:43 localhost dnsmasq[15290]: error at line 2 of /var/run/nm-dns-dnsmasq.conf May 31 13:32:43 localhost dnsmasq[15290]: FAILED to start up May 31 13:32:43 localhost NetworkManager[931]: <info> VPN connection 'Dynalabs' (IP Config Get) complete. May 31 13:32:43 localhost NetworkManager[931]: <info> Policy set 'Dynalabs' (ppp0) as default for IPv4 routing and DNS. May 31 13:32:43 localhost NetworkManager[931]: <info> VPN plugin state changed: started (4) May 31 13:32:43 localhost NetworkManager[931]: <warn> dnsmasq exited with error: Configuration problem (1) May 31 13:32:43 localhost NetworkManager[931]: <info> (ppp0): writing resolv.conf to /sbin/resolvconf May 31 13:32:43 localhost dbus[872]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) May 31 13:32:43 localhost dbus[872]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' May 31 13:33:00 localhost ntpdate[15370]: step time server 91.189.94.4 offset -1.110301 sec May 31 13:33:21 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xd6d6 May 31 13:33:21 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x93aa May 31 13:33:21 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xcc83 May 31 13:33:21 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x2031 May 31 13:33:21 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x13d4 May 31 13:33:22 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x5b11 May 31 13:33:22 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x414b May 31 13:33:22 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x2f5f May 31 13:33:22 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xe9ff May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x8e20 May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x8f0 May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf166 May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x36e6 May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xdd19 May 31 13:33:23 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xda26 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xac5 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x53a5 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x507e May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x1dc5 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf87b May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x2f27 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xd10c May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x66ef May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xa294 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xb15 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x52a2 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xd863 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x8a96 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xde19 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x9763 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xb23 May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x83ca May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x964e May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xe8ae May 31 13:33:24 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf614 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x9b1 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf086 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xbff4 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x66c5 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xe42 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf295 May 31 13:33:25 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x86fe May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x3bc1 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xbaad May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x88b5 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xd7a May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x30d5 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x2d8f May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x3933 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x8d42 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x4b4 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xa205 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x7cc5 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x1b6a May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0xf004 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x21b6 May 31 13:33:26 localhost pppd[15221]: Protocol-Reject for unsupported protocol 0x51eb

  Read the article

• Static IP for dynamic IP

  - by scape279

  I have a dynamic IP address. I would like to have a static IP, but Virgin Media don't allow static IPs for residential broadband services, even if you ask them really nicely and offer to pay for it without switching to a business tariff. I am already registered with a dynamic DNS service which is updated by my router eg me.example.com will always resolve to my dynamic IP. This is fine for some circumstances, but not if you can only enter an IP address into configuration files/hardware etc like firewalls, subversion services etc etc. Is there a way I can have a static IP address 'forwarding' to my dynamic IP? Would a possible solution involve tunnelling? Setting up a private proxy? Please note the following: I am able to buy an IP address from my web host. I have access to a webserver and I am able to create custom DNS zones. I'm happy to have a webserver running at home if necessary also. I do not wish to change broadband providers. I have zero control over the services that require the IP address entering so I cannot tackle the problem that way round (services I need to access are at work). PS I've tried googling this issue, but it is very difficult to search for as most results are related to dynamic dns (which I already have set up and isnt quite what I'm after)

  Read the article

• Ethernet interface number changed, and old one does not exist, but does not leave IP address

  - by Sagar

  I have a virtual machine with Mandriva 2007.0 (yes, old - unfortunately we do not have a choice here). Anyway, the problem: Before reboot: active network interface = eth0. No other interfaces present, and network manager confirms this. Static IP address set to 172.31.2.22. No issues, everything working properly, routing et al. -------Reboot--------- After reboot: active network interface = eth1, with a DHCP address. Network manager shows eth0 as disconnected, and not connectable. When I try to set eth1 up with the static IP address (same one), it says "In Use". I then tried ifconfig eth0 172.31.2.29 just to free it up from the eth0 interface so I could use it with eth1 (since this is connected). Result: ifconfig eth0 172.31.2.29 SIOCSIFADDR: No such device eth0: unknown interface: No such device Nothing else changed. Any ideas what could be happening, or at least how I can get my IP address back?

  Read the article

• Static IP for dynamic IP

  - by scape279

  I have a dynamic IP address. I would like to have a static IP, but Virgin Media don't allow static IPs for residential broadband services, even if you ask them really nicely and offer to pay for it without switching to a business tariff. I am already registered with a dynamic DNS service which is updated by my router eg me.example.com will always resolve to my dynamic IP. This is fine for some circumstances, but not if you can only enter an IP address into configuration files/hardware etc like firewalls, subversion services etc etc. Is there a way I can have a static IP address 'forwarding' to my dynamic IP? Would a possible solution involve tunnelling? Setting up a private proxy? Please note the following: I am able to buy an IP address from my web host. I have access to a webserver and I am able to create custom DNS zones. I'm happy to have a webserver running at home if necessary also. I do not wish to change broadband providers. I have zero control over the services that require the IP address entering so I cannot tackle the problem that way round (services I need to access are at work). PS I've tried googling this issue, but it is very difficult to search for as most results are related to dynamic dns (which I already have set up and isnt quite what I'm after)

  Read the article

• access an IP restricted service from a dynamic IP (Broadband modem) on a windows machine

  - by Joel Alenchery

  Hi, I dont know if this is the correct place to ask this question but here goes .. (please note that I am pretty much a newbie in terms of networking and I work primarily on the windows platform) I have been working on accessing and consuming some web services in C#/ASP.Net, these web services that I consume are IP restricted. Currently they allow access only from my work network (we have a static ip set up through which all our internet requests are routed). Every now and then we have people who go out and about and are stuck with using a usb dongle based internet connection and hence are not able to now access these web services that they are working on. What I would like to do is to provide some way for these remote workers to access the IP restricted web services using the static ip at our office. For example when the remote worker tries to access a service say http://exampleService.com .. the request gets routed to some box at our office and then out to the actual service. That way the service always sees the static ip of the office and not the dynamic ip that the remote user is actually using. I have done a fair bit of googling and its difficult to search for it as most of the results come back for dynamic DNS which is not really what I am looking for. I have also looked at a couple of posts on here namely Accessing IP restricted server from dynamic IP which does provide some insight but the fellow seems to have access to the source that does the ip restriction and is able to change the restrictions. In my case i dont have that access. another one that looked interesting was Static IP for dynamic IP the first answer seems exactly what I need but I dont know how I would go about doing the same on a windows machine. any help would be really appreciated. (am sorry about being soo noob-ish) PS: Right now everyone is using RDC/LogMeIn to access an internet connected machine in the office to manually check the webservice and getting work done. Which is a very tedious process.

  Read the article

• access an IP restricted service from a dynamic IP (Broadband modem) on a windows machine

  - by Joel Alenchery

  Hi, I dont know if this is the correct place to ask this question but here goes .. (please note that I am pretty much a newbie in terms of networking and I work primarily on the windows platform) I have been working on accessing and consuming some web services in C#/ASP.Net, these web services that I consume are IP restricted. Currently they allow access only from my work network (we have a static ip set up through which all our internet requests are routed). Every now and then we have people who go out and about and are stuck with using a usb dongle based internet connection and hence are not able to now access these web services that they are working on. What I would like to do is to provide some way for these remote workers to access the IP restricted web services using the static ip at our office. For example when the remote worker tries to access a service say http://exampleService.com .. the request gets routed to some box at our office and then out to the actual service. That way the service always sees the static ip of the office and not the dynamic ip that the remote user is actually using. I have done a fair bit of googling and its difficult to search for it as most of the results come back for dynamic DNS which is not really what I am looking for. I have also looked at a couple of posts on here namely http://serverfault.com/questions/187231/accessing-ip-restricted-server-from-dynamic-ip which does provide some insight but the fellow seems to have access to the source that does the ip restriction and is able to change the restrictions. In my case i dont have that access. another one that looked interesting was http://serverfault.com/questions/136806/static-ip-for-dynamic-ip the first answer seems exactly what I need but I dont know how I would go about on a windows machine. any help would be really appreciated. (am sorry about being soo noob-ish) PS: Right now everyone is using RDC/LogMeIn to access an internet connected machine in the office to manually check the webservice and getting work done. Which is a very tedious process.

  Read the article

• Bind an ip address to Postfix as outgoing ip

  - by jack

  Is that possible to bind all available public ip addresses on a server to one Postfix instance as its outgoing ip pool and let it choose a random ip or specified ip from the pool each time it sends out an email? If above is not possible, can it be configured to listen on one public ip address per instance and each time it delivers a message, it use the binded one as outgoing ip address.

  Read the article

• Watchguard firebox: public IP addresses behind firewall with as much usable IP addresses as possible

  - by martinezpt

  Our ISP assigned us 16 public IP addresses that we want to assign to hosts behind a Watchguard firebox x750e. The IP addresses are: x.x.x.176/28 of which x.x.x.177 is the gateway. The hosts will be running software that needs to be directly assigned the public IP address so 1:1 NAT is not an option. I found this document that gives examples on how to assign public IP addresses to hosts behind the firewall, using an optional interface: http://www.watchguard.com/help/configuration-examples/public_IP_behind_XTM_configuration_example_(en-US).pdf However, I can't implement scenario 1 as it won't allow me to use the same subnet on both interfaces. As for scenario 2, splitting the address range into 2 subnets will decrease the usable hosts on the optional interface to 5 (8 - network - broadcast - optional interface ip). I'm convinced that there must be a better way to address this problem and maximize the number of usable IP addresses but I'm not very familiar with this specific firewall. Are there any suggestions on how to keep the hosts behind the firewall with public IP addresses while maximizing the usable IP addresses? thanks

  Read the article

• Getting USB Wifi device to work

  - by Lolwhites

  I have been trying to get an Olitec Wifi N USB dongle to work. At first it lit up but wouldn't connect. A little Googling suggested that it would need ndiswrapper to make it work. After installing and trying to add driver with ndisgtk, I got the error message FATAL: Module ndiswrapper not found., but the driver appears in the list of currently installed ones anyway. However, the situation appears even worse: The USB device doesn't even light up (which it does when plugged into my netbook), suggesting the thing isn't detected any more. How to I go about resolving this issue? I've tried uninstalling ndiswrapper but there seems to have been some permanent change as the device is still not lighting up, as it did at first. Edit: Contents of /etc/modprobe.d/ndiswrapper.conf alias usb:v04F2pAFF7d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v04F2pAFF8d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v04F2pAFF9d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v04F2pAFFAd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v04F2pAFFBd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v04F2pAFFCd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v050Dp1102d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v050Dp2102d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v050Dp2103d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0586p341Fd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v06F8pE033d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v07AAp0056d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v07B8p8178d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v07B8p8189d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0B05p17ABd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8170d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8176d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8177d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8178d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp817Ad*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp817Bd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp817Cd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp817Ed*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp817Fd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8186d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BDAp8192d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0BFFp8160d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0DF6p0052d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0DF6p005Cd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0DF6p0061d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v0EB0p9071d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v103Cp1629d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v13D3p3357d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v13D3p3358d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v13D3p3359d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2001p3307d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2001p3308d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2001p3309d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2001p330Ad*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019p1201d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019p4902d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019p4903d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019p4904d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019pAB2Ad*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019pAB2Bd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019pAB2Cd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019pAB2Ed*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v2019pED17d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v20F4p624Dd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v20F4p648Bd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v20F4p664Bd*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v4855p0090d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v4855p0091d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v4856p0091d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v7392p7811d*dc*dsc*dp*ic*isc*ip* ndiswrapper alias usb:v7392p7822d*dc*dsc*dp*ic*isc*ip* ndiswrapper

  Read the article

• multiple ip for a server not reachable

  - by andrewk

  FYI: I've read everything on Serverfault related to this question and have faced a different issue. Simply put, I've got one server (apache2) with couple of sites on it. It currently has 1 ip. I'm trying to assign/add another ip to that server, so I can give each site a different ip for ssl purposes. I am not lucking out. The new ip simply is unreachable, I've pinged it. This is what I've got below, what am I doing wrong. auto lo iface lo inet loopback auto eth0 eth0:0 eth0:1 iface eth0 inet static address 70.116.5.244 netmask 255.255.255.0 gateway 70.116.5.1 #THE NEW IP iface eth0:0 inet static address 26.175.217.102 netmask 255.255.255.0 #PRIVATE IP iface eth0:1 inet static address 192.168.158.88 netmask 255.255.128.0 NOTE: THESE IP'S ARE TWEAKED BUT RELATIVE I've read many questions here 90% similar to this but most actually have the IP respond, not this case. Thanks netstar -r output Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default gw-u6.linode.co 0.0.0.0 UG 0 0 0 eth0 70.116.5.0 * 255.255.255.0 U 0 0 0 eth0 26.175.217.0 * 255.255.255.0 U 0 0 0 eth0 192.168.128.0 * 255.255.128.0 U 0 0 0 eth0

  Read the article

• IP alias lost when changing main IP

  - by rmflow

  my /etc/network/interfaces: auto eth0 iface eth0 inet static address 192.168.3.75 netmask 255.255.255.0 gateway 192.168.3.0 Situation 1: After linux booted I set an IP alias: ifconfig eth0:0 192.168.3.111 Now ifconfig reports two IP addresses 192.168.3.75 at eth0 and 192.168.3.111 at eth0:0 When I change main IP to another network: ifconfig eth0 192.168.1.111 the alias eth0:0 is lost! Situation 2: After linux booted I set an IP alias: ifconfig eth0:0 192.168.4.111 Now ifconfig reports two IP addresses 192.168.3.75 at eth0 and 192.168.4.111 at eth0:0 When I change main IP to another network: ifconfig eth0 192.168.1.111 the alias eth0:0 stays! How do I properly change main IP, so all my aliases are not lost?

  Read the article

• Errors when switching to specific static IP

  - by michaelc

  I had a Fedora box running using my static IP 69.169.136.6, etc, all configured according to what the ISP required. Just recently the hard drive failed (and I should have been keeping better backups) - while it is being recovered I would like to put up a webpage on my Archlinux PC explaining the problem - I presently do not have sufficient access to change the DNS record assigned to the domain. When I change my ip address while my system is running to 69.169.136.6, ifconfig reports the new ip address, but http://whatismyip.com/ does not. When I change it and reboot, I can't ping - the message I recieve is "connect: Network is unreachable" (when given one of google.com 's IP addresses - hostnames give me ping: unknown host xxx). Until I have access to the DNS system, what can I do to make this work? Edit: With new IP address, same problem, IP is now 69.169.136.29. Some commands might be useful: #ping 69.169.136.1 PING 69.169.136.1 (69.169.136.1) 56(84) bytes of data. 64 bytes from 69.169.136.1: icmp_seq=1 ttl=64 time=0.377 ms #ping 69.169.190.211 connect: Network is unreachable #ping 208.72.160.67 connect: Network is unreachable #ifconfig eth0 Link encap:Ethernet HWaddr 00:E0:4D:97:23:9B inet addr:69.169.136.29 Bcast:69.169.137.255 Mask:255.255.254.0 inet6 addr: fe80::2e0:4dff:fe97:239b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:132091 errors:0 dropped:0 overruns:0 frame:0 TX packets:17 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9635179 (9.1 Mb) TX bytes:1322 (1.2 Kb) Interrupt:29 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:48 errors:0 dropped:0 overruns:0 frame:0 TX packets:48 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2480 (2.4 Kb) TX bytes:2480 (2.4 Kb) #ip route 69.169.136.0/23 dev eth0 proto kernel scope link src 69.169.136.29 #cat /etc/resolv.conf # Generated by dhcpcd #nameserver 208.67.222.222 #nameserver 208.67.220.220 nameserver 69.169.190.211 nameserver 208.72.160.67 # /etc/resolv.conf.tail can replace this line Update: have new static IP addresses, verified to work in Windows... Relevant portions of /etc/rc.conf below: #Static IP example #eth0="eth0 69.169.136.6 netmask 255.255.254.0 broadcast 69.169.136.1" #eth0="eth0 69.169.136.29 netmask 255.255.254.0 broadcast 69.169.137.255" eth0="eth0 69.169.136.32 netmask 255.255.254.0 broadcast 69.169.137.255" #eth0="dhcp" INTERFACES=(eth0) # Routes to start at boot-up (in this order) # Declare each route then list in ROUTES # - prefix an entry in ROUTES with a ! to disable it # #gateway="default gw 192.168.0.1" gateway="default gw 69.169.136.1" #gateway="69.169.136.1" ROUTES=(!gateway) #ROUTES=()

  Read the article

• VRF Internet Gateway Multiple External IP's 1 Internal IP to AWS

  - by user223903

  Trying to setup VRF for the first time and its not working for me even though I keep reading everything online. IP's are different to real life. I have an Internet connection which I can ping to my router in the current setup below 195.45.73.22 I have a block of ip addresses 195.45.121.0/27 I want to setup multiple VPN's to AWS so need to have multiple external ip's thus the block of IP addresses. I have setup the 2nd and 3rd IP address but can not ping them from external. Any help would be grateful. Bryan ip source-route ! ip vrf Internet rd 1:1 route-target export 1:1 route-target import 1:1 ip vrf AWSSydney1 rd 2:2 route-target export 2:2 route-target import 2:2 route-target import 1:1 ip vrf AWSSydney2 rd 3:3 route-target export 3:3 route-target import 3:3 route-target import 1:1 ip cef no ip domain lookup no ipv6 cef multilink bundle-name authenticated interface FastEthernet0/0 description Vocus Internet no ip address speed 100 full-duplex interface FastEthernet0/0.1 encapsulation dot1Q 1 native ip address 195.45.73.22 255.255.255.252 interface FastEthernet0/0.2 encapsulation dot1Q 2 ip vrf forwarding AWSSydney1 ip address 195.45.121.1 255.255.255.224 interface FastEthernet0/0.3 encapsulation dot1Q 3 ip vrf forwarding AWSSydney2 ip address 195.45.121.2 255.255.255.224 interface FastEthernet0/1 description LAN_SIDE ip address 10.0.0.5 255.255.255.0 speed 100 full-duplex no mop enabled ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 195.45.73.21 ip route vrf Internet 0.0.0.0 0.0.0.0 195.45.73.21

  Read the article

• Server can't set IP after power outage

  - by Ali

  The power went out all of a sudden and when we tried to restart everything when it came back on - our server can't be assigned an IP? We got an error stating that the IP for the server was already in use by another system. We then shut down all systems and restarted the server but then for some reason the server was assigned an IP but no one could connect to it - after restarting the server after setting it to have a dynamically assigned ip - the server now has no ip - just 0.0.0.0 - running an ipconfig/renew or ipconfig /release has no effect.. what should we do!!

  Read the article

• Finding all IP ranges blelonging to a specific ISP

  - by Jim Jim

  I'm having an issue with a certain individual who keeps scraping my site in an aggressive manner; wasting bandwidth and CPU resources. I've already implemented a system which tails my web server access logs, adds each new IP to a database, keeps track of the number of requests made from that IP, and then, if the same IP goes over a certain threshold of requests within a certain time period, it's blocked via iptables. It may sound elaborate, but as far as I know, there exists no pre-made solution designed to limit a certain IP to a certain amount of bandwidth/requests. This works fine for most crawlers, but an extremely persistent individual is getting a new IP from his/her ISP pool each time they're blocked. I would like to block the ISP entirely, but don't know how to go about it. Doing a whois on a few sample IPs, I can see that they all share the same "netname", "mnt-by", and "origin/AS". Is there a way I can query the ARIN/RIPE database for all subnets using the same mnt-by/AS/netname? If not, how else could I go about getting every IP belonging to this ISP? Thanks.

  Read the article

• Blocking an IP range without using .htaccess

  - by Chris

  I have a WordPress blog that I am hosting using NearlyFreeSpeech.net. Recently, Russians found it and have been comment spamming me. I don't want to have to trash 30+ Cyrillic comments/day, and I don't want to pay for that bandwidth either. I did a little research, and all the commentors are originating from RIPE delegated IP ranges. Because my blog can only interest people living in the American Southeast, I figured the quick and dirty solution would be to use .htaccess to deny connections coming from 62.0.0.0/8 and 80.0.0.0/8 - 91.0.0.0/8. I wrote a .htaccess file that did just this, but the Russians were still getting through! According to NearlyFreeSpeech.net's FAQ, they can't support IP blocking through .htaccess (dirt cheap hosting comes with a price). I can block comments by IP through Wordpress (I think), but I can't figure out a way to block IP ranges or wildcards. Does anybody know of any other way?

  Read the article

• IP failover with 2 nodes on different subnet: cannot ping virtual IP from second node?

  - by quanta

  I'm going to setup redundant failover Redmine: another instance was installed on the second server without problem MySQL (running on the same machine with Redmine) was configured as master-master replication Because they are in different subnet (192.168.3.x and 192.168.6.x), it seems that VIPArip is the only choice. /etc/ha.d/ha.cf on node1 logfacility none debug 1 debugfile /var/log/ha-debug logfile /var/log/ha-log autojoin none warntime 3 deadtime 6 initdead 60 udpport 694 ucast eth1 node2.ip keepalive 1 node node1 node node2 crm respawn /etc/ha.d/ha.cf on node2: logfacility none debug 1 debugfile /var/log/ha-debug logfile /var/log/ha-log autojoin none warntime 3 deadtime 6 initdead 60 udpport 694 ucast eth0 node1.ip keepalive 1 node node1 node node2 crm respawn crm configure show: node $id="6c27077e-d718-4c82-b307-7dccaa027a72" node1 node $id="740d0726-e91d-40ed-9dc0-2368214a1f56" node2 primitive VIPArip ocf:heartbeat:VIPArip \ params ip="192.168.6.8" nic="lo:0" \ op start interval="0" timeout="20s" \ op monitor interval="5s" timeout="20s" depth="0" \ op stop interval="0" timeout="20s" \ meta is-managed="true" property $id="cib-bootstrap-options" \ stonith-enabled="false" \ dc-version="1.0.12-unknown" \ cluster-infrastructure="Heartbeat" \ last-lrm-refresh="1338870303" crm_mon -1: ============ Last updated: Tue Jun 5 18:36:42 2012 Stack: Heartbeat Current DC: node2 (740d0726-e91d-40ed-9dc0-2368214a1f56) - partition with quorum Version: 1.0.12-unknown 2 Nodes configured, unknown expected votes 1 Resources configured. ============ Online: [ node1 node2 ] VIPArip (ocf::heartbeat:VIPArip): Started node1 ip addr show lo: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet 192.168.6.8/32 scope global lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever I can ping 192.168.6.8 from node1 (192.168.3.x): # ping -c 4 192.168.6.8 PING 192.168.6.8 (192.168.6.8) 56(84) bytes of data. 64 bytes from 192.168.6.8: icmp_seq=1 ttl=64 time=0.062 ms 64 bytes from 192.168.6.8: icmp_seq=2 ttl=64 time=0.046 ms 64 bytes from 192.168.6.8: icmp_seq=3 ttl=64 time=0.059 ms 64 bytes from 192.168.6.8: icmp_seq=4 ttl=64 time=0.071 ms --- 192.168.6.8 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3000ms rtt min/avg/max/mdev = 0.046/0.059/0.071/0.011 ms but cannot ping virtual IP from node2 (192.168.6.x) and outside. Did I miss something? PS: you probably want to set IP2UTIL=/sbin/ip in the /usr/lib/ocf/resource.d/heartbeat/VIPArip resource agent script if you get something like this: Jun 5 11:08:10 node1 lrmd: [19832]: info: RA output: (VIPArip:stop:stderr) 2012/06/05_11:08:10 ERROR: Invalid OCF_RESK EY_ip [192.168.6.8] http://www.clusterlabs.org/wiki/Debugging_Resource_Failures Reply to @DukeLion: Which router receives RIP updates? When I start the VIPArip resource, ripd was run with below configuration file (on node1): /var/run/resource-agents/VIPArip-ripd.conf: hostname ripd password zebra debug rip events debug rip packet debug rip zebra log file /var/log/quagga/quagga.log router rip !nic_tag no passive-interface lo:0 network lo:0 distribute-list private out lo:0 distribute-list private in lo:0 !metric_tag redistribute connected metric 3 !ip_tag access-list private permit 192.168.6.8/32 access-list private deny any

  Read the article

• finding IP address using Linux command prompt

  - by John Kube

  I'm looking for a way to get my IP address using the command prompt in Linux. I know when you type "ifconfig" you can get your local IP address (i.e. 192.168.0.103), but I'm looking for my IP address that I get from my ISP. How can I get this from Linux without having to visit some website?

  Read the article

• Same netmask or /32 for secondary IP on Linux

  - by derobert

  There appear to be (at least) two ways to add a secondary IP address to an interface on Linux. By secondary, I mean that it'll accept traffic to the IP address, and responses to connections made to that IP will use it as a source, but any traffic the box originates (e.g., an outgoing TCP connection) will not use the secondary address. Both ways start with adding the primary address, e.g., ip addr add 172.16.8.10/24 dev lan. Then I can add the secondary address with either a netmask of /24 (matching the primary) or /32. If I add it with a /24, it gets flagged secondary, so will not be used as the source of outgoing packets, but that leaves a risk of the two addresses being added in the wrong order by mistake. If I add it with /32, wrong order can't happen, but it doesn't get flagged as secondary, and I'm not sure what the bad effects of that may be. So, I'm wondering, which approach is least likely to break? (If it matters, the main service on this machine is MySQL, but it also runs NFSv3. I'm adding a second machine as a warm standby, and hope to switch between them by changing which owns the secondary IP.)

  Read the article

• Likeliness of obtaining same IP address after restarting a router

  - by ?affael

  My actual objective is to simulate logged IPs of web-site users who are all assumed to use dynamically assigned IPs. There will be two kinds of users: good users who only change IP when the ISP assignes a new one bad users who will restart their router to obtain a new IP So what I would like to understand is what assignment mechanics are usually at work here deciding from what pool of IPs one is chosen and whether the probability is uniformly distributed. I know there is no definite and global answer as this process can be adjusted be the ISP but maybe there is something like a technological frame and common process that allows some plausible assumptions. UPDATE: A bad user will restart the router as often as possible if necessary. So here the central question is how many IP changes on average are necessary to end up with a previously used IP.

  Read the article

• Howto find internal IP server by external IP

  - by HWTech

  I've got 12 servers in datacenter, but can login by SSH into one of them (facade server), other servers available only from it. In hosts file we have ip list each of available servers. milkov@devel:/var/www/davel$ cat /etc/hosts 192.168.1.4 data1 192.168.1.7 data2 192.168.1.5 bground1 192.168.1.6 bground2 192.168.1.10 frontend1 192.168.1.11 frontend2 ... Also I've domain megaplan.tvigle.ru (IP 79.142.100.36). Question: How to know which one of servers serve this domain? How to find servers internal ip-address by external IP. PS: Sorry about my Eng. lng

  Read the article

• What is the necessity of IP-in-IP?

  - by Claudiu

  There is even a standard for IP in IP encapsulation. What is the use case here? I can understand stuff like TCP over DNS, where IP might be unavailable, but if you can do IP in IP, couldn't you simply do regular IP?

  Read the article

• Cisco 800 series won't forward port

  - by sam

  Hello ServerFault, I am trying to forward port 444 from my cisco router to my Web Server (192.168.0.2). As far as I can tell, my port forwarding is configured correctly, yet no traffic will pass through on port 444. Here is my config: ! version 12.3 service config no service pad service tcp-keepalives-in service tcp-keepalives-out service timestamps debug uptime service timestamps log uptime service password-encryption no service dhcp ! hostname QUESTMOUNT ! logging buffered 16386 informational logging rate-limit 100 except warnings no logging console no logging monitor enable secret 5 -removed- ! username administrator secret 5 -removed- username manager secret 5 -removed- clock timezone NZST 12 clock summer-time NZDT recurring 1 Sun Oct 2:00 3 Sun Mar 3:00 aaa new-model ! ! aaa authentication login default local aaa authentication login userlist local aaa authentication ppp default local aaa authorization network grouplist local aaa session-id common ip subnet-zero no ip source-route no ip domain lookup ip domain name quest.local ! ! no ip bootp server ip inspect name firewall tcp ip inspect name firewall udp ip inspect name firewall cuseeme ip inspect name firewall h323 ip inspect name firewall rcmd ip inspect name firewall realaudio ip inspect name firewall streamworks ip inspect name firewall vdolive ip inspect name firewall sqlnet ip inspect name firewall tftp ip inspect name firewall ftp ip inspect name firewall icmp ip inspect name firewall sip ip inspect name firewall fragment maximum 256 timeout 1 ip inspect name firewall netshow ip inspect name firewall rtsp ip inspect name firewall skinny ip inspect name firewall http ip audit notify log ip audit po max-events 100 ip audit name intrusion info list 3 action alarm ip audit name intrusion attack list 3 action alarm drop reset no ftp-server write-enable ! ! ! ! crypto isakmp policy 1 authentication pre-share ! crypto isakmp policy 2 encr 3des authentication pre-share group 2 ! crypto isakmp client configuration group staff key 0 qS;,sc:q<skro1^, domain quest.local pool vpnclients acl 106 ! ! crypto ipsec transform-set tr-null-sha esp-null esp-sha-hmac crypto ipsec transform-set tr-des-md5 esp-des esp-md5-hmac crypto ipsec transform-set tr-des-sha esp-des esp-sha-hmac crypto ipsec transform-set tr-3des-sha esp-3des esp-sha-hmac ! crypto dynamic-map vpnusers 1 description Client to Site VPN Users set transform-set tr-des-md5 ! ! crypto map cm-cryptomap client authentication list userlist crypto map cm-cryptomap isakmp authorization list grouplist crypto map cm-cryptomap client configuration address respond crypto map cm-cryptomap 65000 ipsec-isakmp dynamic vpnusers ! ! ! ! interface Ethernet0 ip address 192.168.0.254 255.255.255.0 ip access-group 102 in ip nat inside hold-queue 100 out ! interface ATM0 no ip address no atm ilmi-keepalive dsl operating-mode auto ! interface ATM0.1 point-to-point pvc 0/100 encapsulation aal5mux ppp dialer dialer pool-member 1 ! ! interface Dialer0 bandwidth 640 ip address negotiated ip access-group 101 in no ip redirects no ip unreachables ip nat outside ip inspect firewall out ip audit intrusion in encapsulation ppp no ip route-cache no ip mroute-cache dialer pool 1 dialer-group 1 no cdp enable ppp pap sent-username -removed- password 7 -removed- ppp ipcp dns request crypto map cm-cryptomap ! ip local pool vpnclients 192.168.99.1 192.168.99.254 ip nat inside source list 105 interface Dialer0 overload ip nat inside source static tcp 192.168.0.2 444 interface Dialer0 444 ip nat inside source static tcp 192.168.0.51 9000 interface Dialer0 9000 ip nat inside source static udp 192.168.0.2 1433 interface Dialer0 1433 ip nat inside source static tcp 192.168.0.2 1433 interface Dialer0 1433 ip nat inside source static tcp 192.168.0.2 25 interface Dialer0 25 ip classless ip route 0.0.0.0 0.0.0.0 Dialer0 ip http server no ip http secure-server ! ip access-list logging interval 10 logging 192.168.0.2 access-list 1 remark The local LAN. access-list 1 permit 192.168.0.0 0.0.0.255 access-list 2 permit 192.168.0.0 access-list 2 remark Where management can be done from. access-list 2 permit 192.168.0.0 0.0.0.255 access-list 3 remark Traffic not to check for intrustion detection. access-list 3 deny 192.168.99.0 0.0.0.255 access-list 3 permit any access-list 101 remark Traffic allowed to enter the router from the Internet access-list 101 permit ip 192.168.99.0 0.0.0.255 192.168.0.0 0.0.0.255 access-list 101 deny ip 0.0.0.0 0.255.255.255 any access-list 101 deny ip 10.0.0.0 0.255.255.255 any access-list 101 deny ip 127.0.0.0 0.255.255.255 any access-list 101 deny ip 169.254.0.0 0.0.255.255 any access-list 101 deny ip 172.16.0.0 0.15.255.255 any access-list 101 deny ip 192.0.2.0 0.0.0.255 any access-list 101 deny ip 192.168.0.0 0.0.255.255 any access-list 101 deny ip 198.18.0.0 0.1.255.255 any access-list 101 deny ip 224.0.0.0 0.15.255.255 any access-list 101 deny ip any host 255.255.255.255 access-list 101 permit tcp 67.228.209.128 0.0.0.15 any eq 1433 access-list 101 permit tcp host 120.136.2.22 any eq 1433 access-list 101 permit tcp host 123.100.90.58 any eq 1433 access-list 101 permit udp 67.228.209.128 0.0.0.15 any eq 1433 access-list 101 permit udp host 120.136.2.22 any eq 1433 access-list 101 permit udp host 123.100.90.58 any eq 1433 access-list 101 permit tcp any any eq 444 access-list 101 permit tcp any any eq 9000 access-list 101 permit tcp any any eq smtp access-list 101 permit udp any any eq non500-isakmp access-list 101 permit udp any any eq isakmp access-list 101 permit esp any any access-list 101 permit tcp any any eq 1723 access-list 101 permit gre any any access-list 101 permit tcp any any eq 22 access-list 101 permit tcp any any eq telnet access-list 102 remark Traffic allowed to enter the router from the Ethernet access-list 102 permit ip any host 192.168.0.254 access-list 102 deny ip any host 192.168.0.255 access-list 102 deny udp any any eq tftp log access-list 102 permit ip 192.168.0.0 0.0.0.255 192.168.99.0 0.0.0.255 access-list 102 deny ip any 0.0.0.0 0.255.255.255 log access-list 102 deny ip any 10.0.0.0 0.255.255.255 log access-list 102 deny ip any 127.0.0.0 0.255.255.255 log access-list 102 deny ip any 169.254.0.0 0.0.255.255 log access-list 102 deny ip any 172.16.0.0 0.15.255.255 log access-list 102 deny ip any 192.0.2.0 0.0.0.255 log access-list 102 deny ip any 192.168.0.0 0.0.255.255 log access-list 102 deny ip any 198.18.0.0 0.1.255.255 log access-list 102 deny udp any any eq 135 log access-list 102 deny tcp any any eq 135 log access-list 102 deny udp any any eq netbios-ns log access-list 102 deny udp any any eq netbios-dgm log access-list 102 deny tcp any any eq 445 log access-list 102 permit ip 192.168.0.0 0.0.0.255 any access-list 102 permit ip any host 255.255.255.255 access-list 102 deny ip any any log access-list 105 remark Traffic to NAT access-list 105 deny ip 192.168.0.0 0.0.0.255 192.168.99.0 0.0.0.255 access-list 105 permit ip 192.168.0.0 0.0.0.255 any access-list 106 remark User to Site VPN Clients access-list 106 permit ip 192.168.0.0 0.0.0.255 any dialer-list 1 protocol ip permit ! line con 0 no modem enable line aux 0 line vty 0 4 access-class 2 in transport input telnet ssh transport output none ! scheduler max-task-time 5000 ! end any ideas? :)

  Read the article

• Rapidly changing public IP addresses on certain networks?

  - by zenblender

  I run/develop an online game where many of our users are in southeast asia. I recently went to southeast asia and made an alarming discovery. Anywhere I got internet access, whether it was via 3G, a LAN in a hotel, or wifi in a cafe, both in Singapore and the Philippines, I noticed that my IP address was changing CONSTANTLY. I mean the public IP address, not the private one. I could load a page like whatismyip.com and just hit reload and see a new IP address show up every 5-10 seconds! This has lots of consequences for my online game, as many things "break" if the IP address changes for a given user. Basically, I would like to know more about this. Is there a name for the kind of network or router or paradigm that causes this, so I can read up on it? I don't understand WHY a network would function this way. Does it do this on purpose? Is it for security reasons? Is it to anonymize and protect the identity of the users? Or is it just an "old" method that is mostly obsolete in the rest of the world? Thanks for any info that will help me to understand.

  Read the article

• Creating Hosting Accounts in WHM on a Single IP

  - by Daniel Hanly

  I've just purchased a VPS with the hope of transferring multiple shared hosting accounts onto it. The problem is that I've only got 2 IP addresses with my VPS. I can create an account and assign it an IP address, but once I've done this once, I can't do it again. (1 IP address is my main root WHM IP, the other is my new hosting account IP). Can I create multiple hosting accounts and use the same IP? How would I manage multiple hosting accounts in this way? The domain for this hosting account has been purchased by the client, and they hold it (can't transfer for 60 days), so I need to adjust the DNS settings to redirect to my newly created hosting area - how can I do this without a dedicated IP address?

  Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >