Search Results

Search found 168 results on 7 pages for 'iwconfig'.

Page 1/7 | 1 2 3 4 5 6 7  | Next Page >

• Wireless iwconfig rate auto too low

  - by Jamie Kitson

  Hi, left to its own devices my wireless connects at too low a speed. I have a 20meg internet connection and my wireless is slowing it down to like 3meg. When I reboot into windows it's fine. When I run iwconfig eth1 rate 24M or even 48M the connection is much faster and runs fine, why won't it automatically go higher? Is this the fault of the driver? I am running Broadcom's driver compiled from source. Would adding iwconfig eth1 rate 24M to rc.local be the right way to force it at boot? Output from iwconfig when rate=auto: eth1 IEEE 802.11 ESSID:"honeypot" Mode:Managed Frequency:2.417 GHz Access Point: xxx Bit Rate=1 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=5/5 Signal level=-47 dBm Noise level=-91 dBm Rx invalid nwid:0 Rx invalid crypt:2 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Thanks, Jamie

  Read the article

• iwconfig usage for WEP access point?

  - by johan elmander

  I would like to use my wifi doggle in my pc (ubuntu 12.04). I am able to connect to my access point through the GUI. I would like to do the same in the terminal. My access point uses WEP. So I typed the following commands iwconfig wlan0 mode managed key 6d6f6e6579 iwconfig wlan0 essid "AccessPoint" dhclient wlan0 after typing dhclient wlan0 it waits like 1-2 min then outputs nothing and cannot connect to the Access Point. iwconfig output: wlan0 IEEE 802.11bgn ESSID:"AccessPoint" Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long timit:7 RTS thr=2347 B Fragment thr:off Encryption key:6D6F-6E65-79 Power Management:off I would appreciate any suggestion

  Read the article

• parsing ssid with iwconfig in c

  - by user1781595

  I am about building a bar for DWM (ubuntu linux), showing wifi details such as the ssid. Thats my code: #include <stdio.h> #include <stdlib.h> int main( int argc, char *argv[] ) { FILE *fp; int status; char path[1035]; /* Open the command for reading. */ fp = popen("iwconfig", "r"); if (fp == NULL) { printf("Failed to run command\n" ); exit; } char s[500]; /* Read the output a line at a time - output it. */ while (fgets(path, sizeof(path)-1, fp) != NULL) { sprintf(s,"%s%s",s, path); } //printf("%s",s); /* close */ pclose(fp); char delimiter[1] = "s"; char *ptr; ptr = strtok(s, delimiter); printf("SSID: %s\n", ptr); return 0; } i am getting overflowerrors and dont know what to do. I dont think, thats a good way to get the ssid either... :/ Suggestions?

  Read the article

• iwconfig, iw not displaying wireless information

  - by Srivatsa Kanchi

  after fresh install to 12.10, the wireless information is not shown by both iwconfig and iw. The wireless sets up successfully and able to connect This is what i get $ iwconfig wlan0 wlan0 IEEE 802.11abgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off $ iw wlan0 link Not connected. $ uname -a Linux srivatsa-ThinkPad-T61 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux

  Read the article

• Can't control connection bit rate using iwconfig with Atheros TL-WN821N (AR7010)

  - by Paul H

  I'm trying to reduce the connection bit rate on my Atheros TP-Link TL-WN821N v3 usb wifi adapter due to frequent instability issues (reported connection speed goes down to 1Mb/s and I have to physically reconnect the adapter to regain a connection). I know this is a common problem with this device, and I have tried everything I can think of to fix it, including using drivers from linux-backports; compiling and installing a custom firmware (following instructions on https://wiki.debian.org/ath9k_htc#fw-free) and (as a last resort) using ndiswrapper. When using ndiswrapper, the wifi adapter is stable and operates in g mode at 54Mb/s (whilst when using the default ath9k_htc module, the adapter connects in n mode and the bit rate fluctuates constantly). Unfortunately, with this setup I have to run my processor using only one core, since using SMP with ndiswrapper causes a kernel oops on my system. So I want to lock my bit rate to 54Mb/s (or less, if need be) for connection stability, using the ath9k_htc module. I've tried 'sudo iwconfig wlan0 rate 54M'; the command runs with no error but when I check the bit rate with 'sudo iwlist wlan0 bitrate' the command returns: wlan0 unknown bit-rate information. Current Bit Rate:78 Mb/s Any ideas? Here's some info (hopefully relevant) on my setup: Xubuntu (12.04.3) 64bit (kernel 3.2.0-55.85-generic) using Network Manager. My Router is from Virgin Media, the VMDG480. lshw -C network : *-network description: Wireless interface physical id: 1 bus info: usb@1:4 logical name: wlan0 serial: 74:ea:3a:8f:16:b6 capabilities: ethernet physical wireless configuration: broadcast=yes driver=ath9k_htc driverversion=3.2.0-55 firmware=1.3 ip=192.168.0.9 link=yes multicast=yes wireless=IEEE 802.11bgn lsusb -v: Bus 001 Device 003: ID 0cf3:7015 Atheros Communications, Inc. TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 idVendor 0x0cf3 Atheros Communications, Inc. idProduct 0x7015 TP-Link TL-WN821N v3 802.11n [Atheros AR7010+AR9287] bcdDevice 2.02 iManufacturer 16 ATHEROS iProduct 32 UB95 iSerial 48 12345 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 60 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 6 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 0 bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 1 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 255 Vendor Specific Class bDeviceSubClass 255 Vendor Specific Subclass bDeviceProtocol 255 Vendor Specific Protocol bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) iwlist wlan0 scanning: wlan0 Scan completed : Cell 01 - Address: C4:3D:C7:3A:1F:5D Channel:1 Frequency:2.412 GHz (Channel 1) Quality=37/70 Signal level=-73 dBm Encryption key:on ESSID:"my essid" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s Mode:Master Extra:tsf=00000070cca77186 Extra: Last beacon: 5588ms ago IE: Unknown: 0007756E69636F726E IE: Unknown: 010882848B962430486C IE: Unknown: 030101 IE: Unknown: 2A0100 IE: Unknown: 2F0100 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 32040C121860 IE: Unknown: 2D1AFC181BFFFF000000000000000000000000000000000000000000 IE: Unknown: 3D1601080400000000000000000000000000000000000000 IE: Unknown: DD7E0050F204104A0001101044000102103B00010310470010F99C335D7BAC57FB00137DFA79600220102100074E657467656172102300074E6574676561721024000631323334353610420007303030303030311054000800060050F20400011011000743473331303144100800022008103C0001011049000600372A000120 IE: Unknown: DD090010180203F02C0000 IE: WPA Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00 iwconfig: lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"my essid" Mode:Managed Frequency:2.412 GHz Access Point: C4:3D:C7:3A:1F:5D Bit Rate=78 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0,

  Read the article

• The meaning of the first line output in the iwconfig command in Linux

  - by John Smith

  When I'm using the iwconfig command on my current wifi interface , wlan0 , the first line I get as output is wlan0 IEEE 802.11bgn. When I try to do this when I am connected to other WiFi's, I sometimes get other versions, like IEEE 802.11bg or IEEE 802.11abgn. I want to ask, what's the meaning of this output? if the output is IEEE 802.11bgn then it means that this WiFi supports both the b , g and n standards or it means something else? Thnaks :)

  Read the article

• Ad-Hoc mode and Cell (how does it work)?

  - by Ori Cohen

  hello, I am setting up a wireless Ad-Hoc network manually in linux using iwconfig and ifconfig. I have gotten everything working, and I think I understand it all except access point. The part that confused me is this: If I have essid='some_id', channel=11, Mode=Ad-Hoc and appropriate routing/ip on both laptops, why do I need to make sure the Cell is the same? I was under the impression that Ad-Hoc worked independently of the access point. I can easily get around this, I just use iwconfig wlan0 ap 00:00:00:00:00:01 Why is this necessary? I've been unable to find a good tutorial on this. If anyone can clear this up I'd appreciate it. Thanks

  Read the article

• Can you explain how to understand what the 'iwconfig' command displays in Ubuntu-9.04?

  - by Shawn

  I'm having trouble making my wireless connection work, and I realized I don't really know how to use the tools I have, in this case, the iwconfig command in Ubuntu-9.04. Here is what I get: ***iwconfig*** - lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Network" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=20 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 vboxnet0 no wireless extensions. pan0 no wireless extensions. "Network" is the name of my wireless network, btw. But what does this all mean? How can this information help me aquire a working wireless connection? When I try associating a key using sudo iwconfig wlan0 key s:my_key I get the following error message: Error for wireless request "Set Encode" (8B2A) : SET failed on device wlan0 ; Invalid argument. I do have the right key though, so what's the problem?

  Read the article

• Can you explain how to understand what the 'iwconfig' command displays in Ubuntu-9.04?

  - by Shawn

  I'm having trouble making my wireless connection work, and I realized I don't really know how to use the tools I have, in this case, the iwconfig command in Ubuntu-9.04. Here is what I get: ***iwconfig*** - lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Network" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=20 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 vboxnet0 no wireless extensions. pan0 no wireless extensions. "Network" is the name of my wireless network, btw. But what does this all mean? How can this information help me aquire a working wireless connection? When I try associating a key using sudo iwconfig wlan0 key s:my_key I get the following error message: Error for wireless request "Set Encode" (8B2A) : SET failed on device wlan0 ; Invalid argument. I do have the right key though, so what's the problem?

  Read the article

• Atheros AR928X wireless connection makes neighbourhood machine drop off line

  - by funicorn

  I have an Acer laptop with Atheros AR928X wireless card installed, supported by ath9k driver in the linux kernel. There are other 5 computers sharing wireless connection via a TPLink 150Mbit/s wireless router. At first I found the network is a little bit slower than it's in Windows7, which I accepted as it should be. However a very strange thing is, each time I connected to the router and downloaded stuff for a while, one of the computers running Windows7 in my local network dropped off from the router. And if I run my laptop under Windows7, everything is fine. What's even stranger is although the network becomes slower, only the certain computer drops and totally freezes in connection with the router. I'm not willing to conclude it's due to the unhealthy connection from my laptop to the router, however we have confirmed this for more than one times and there is no problem with the network when I'm running WIndows7. I'm extremely confused about what's going on. As a Linux user running Ubuntu over 5 years, I am awared that wireless driver in Linux is badly notorious of lack of stability and slow speed. But is it so bad that the unhealthy wireless connection can do damage to another computer in the same local network? I do see a lot of "Tx excessive retries" in iwconfig output. But how exactly does this happen ? Thanks for your help. I guess I have to use this answer box to show the outputs $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=47/70 Signal level=-63 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:2 Invalid misc:23 Missed beacon:0 To show what's wrong with the wireless connection, I ran iwconfig again within 3 minutes, during which time I hardly did anything and the network was not much busy than being nearly idle $ sudo iwconfig wlan0 IEEE 802.11bgn ESSID:"TP-LINK111" Mode:Managed Frequency:2.427 GHz Access Point: E0:05:C5:E8:A9:92 Bit Rate=121.5 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=48/70 Signal level=-62 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:9 Invalid misc:28 Missed beacon:0 You can see Tx excessive retires and Invalid misc increase very quickly. $ sudo iwlist wlan0 modu wlan0 unknown modulation information. $ sudo iwlist wlan0 channel wlan0 13 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Channel 12 : 2.467 GHz Channel 13 : 2.472 GHz Current Frequency:2.427 GHz (Channel 4)

  Read the article

• Only run CRON job if connected to specific wifi network

  - by Herbert

  I am a newbie to scripting on Linux (Lubuntu), but I would like to make a script that runs a cron job only if my laptop is connected to my home wifi. Is this possible? I guess, I could do something with iwconfig and pull the ESSID from there with grep? So far, I tried this and it seems to work: #!/bin/bash # CRON, connected to specific WIFI clear netid=HOFF216 if iwconfig | grep $netid then clear echo "True, we are connected to $netid" rsync ........... else clear echo "False, we are not connected to $netid" fi

  Read the article

• Wirelss card not being detected in backtrack 5

  - by Jesse Nelson

  I just installed backtrack 5 and I am unable to detect my wireless card. iwconfig doesn't list my interface. I can see that the hardware is present in lspci -vnn (see below) but I can't get the interface detected. I have tried to reinstall the compat-wireless package but I get errors during the build (see below) I have done a ton of researching and I keep hitting a brick wall, mostly because the wiki for backtrack is down and I can't find any good resources. Does anyone know how to fix the issue? Also, does anyone no how I can scan the hardware to determine what NIC is assigning my interface? If I can figure out the interface name I think I can set it up manually by putting up the link and using wireless-tools to manually configure the connection, this is what I had to do in arch on my mac. As stated the wiki for backtrack is down and I can't find any help on the issue. I tried to do the full kernel upgrade suggested in my software update but after the update was complete and I logged back in I had a new log in manager and the only thing I was able to log into was window managers. However, after this update my wireless was working fine. Please help I am new to Linux and the wiki is down, I have nowhere else to turn. Forgot to mention I am using the KDE version, not Gnome. Thanks in advance for any help or support. Attempt at make: root@bt:/usr/src/compat-wireless-3.3-rc1-2# make /usr/src/compat-wireless-3.3-rc1-2/config.mk:254: "WARNING: CONFIG_CFG80211_WEXT will be deactivated or not working because kernel was compiled with CONFIG_WIRELESS_EXT=n. Tools using wext interface like iwconfig will not work. To activate it build your kernel e.g. with CONFIG_LIBIPW=m." make -C /lib/modules/2.6.38/build M=/usr/src/compat-wireless-3.3-rc1-2 modules make: *** /lib/modules/2.6.38/build: No such file or directory. Stop. make: *** [modules] Error 2 lspci output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn -i net lspci: I/O error at net, line 0 root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn 02:00.0 Network controller [0280]: Atheros Communications Inc. Device [168c:0032] (rev ff) (prog-if ff) !!! Unknown header type 7f ( This is the problem but I can't find the solution) Kernel modules: ath9k iwconfig output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• Wifi Direct P2P-go and P2P-client support in ubuntu

  - by giri

  I am trying to get wifi direct working on a laptop with ubuntu 12.04 When I type the command 'iw list' it doesn't show P2P-client or P2P-go under 'supported interface modes.From http://wireless.kernel.org/en/users/Documentation/iw/replace-iwconfig I found that 'iwconfig' was replaced with 'iw'.Does it mean that my hardware doesn't have support for wifi-direct or is it just the software(drivers) issue? If is it just sofware issue please help me to find the right drivers which support wifi-direct. Here is the info about my ethernet controller from the output of 'lspci' 02:00.0 Ethernet controller: Atheros Communication Inc. AR242x / AR542x Wreless Network Adapter (PCI-Express) (rev 01) 06:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8055 PCI-E Gigabit Ethernet Controller (rev 13)

  Read the article

• Two Wifi Icons in Panel [Solved]

  - by Alex

  I have the exact problem in 13.10 as this user Two Wifi indicators in panel. Here are some screenshots: Here are some screenshots from another user: http://ubuntuforums.org/showthread.php?t=2183020&p=12825563 ifconfig and iwconfig outputs $ ifconfig lo Link encap:Local Loopback inet addr:XXXXXX Mask:XXXXXXX inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2243 errors:0 dropped:0 overruns:0 frame:0 TX packets:2243 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:209889 (209.8 KB) TX bytes:209889 (209.8 KB) wlan0 Link encap:Ethernet HWaddr XXXXXXXXX inet addr:XXXXXX Bcast:XXXXXXXX Mask:XXXXXXX inet6 addr: XXXXXXX Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5925 errors:0 dropped:0 overruns:0 frame:0 TX packets:3361 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2951818 (2.9 MB) TX bytes:630579 (630.5 KB) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"XXXXX" Mode:Managed Frequency:2.437 GHz Access Point: XXXXXXXX Bit Rate=72.2 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:153 Invalid misc:472 Missed beacon:0

  Read the article

• Wireless acting weird ubuntu 12.04 LTS

  - by Philip Yeldhos

  I'm kinda new here, so please bear with me. My wireless driver is acting very weird. It shows my router's name, but when it is connecting (after entering the correct password), the icon on the tray is like, refreshing every once in a second, while showing the animation that it is connecting. And after a few seconds, error message come up saying that wireless network is disconnected. I installed the drive through "additional drivers". What info do you need? Somebody please help. philip@philip-HP-Mini-110-3100:~$ sudo iwconfig lo no wireless extensions. eth1 IEEE 802.11 ESSID:"" Mode:Managed Frequency:2.472 GHz Access Point: Not-Associated Bit Rate:72 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-96 dBm Rx invalid nwid:0 Rx invalid crypt:11 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. here's what lspci -v gave me: 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Hewlett-Packard Company Device 1483 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at 52000000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information: Len=78 <?> Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 00-00-82-ff-ff-3f-e0-2a Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, bcma, brcmsmac okay, i removed the driver additional drivers gave me. now, this is what has happened: lsmod gave me: philip@philip-HP-Mini-110-3100:~$ lsmod | grep brc brcmsmac 540875 0 mac80211 436455 1 brcmsmac brcmutil 14675 1 brcmsmac cfg80211 178679 2 brcmsmac,mac80211 crc8 12781 1 brcmsmac cordic 12487 1 brcmsmac and iwconfig gave me: philip@philip-HP-Mini-110-3100:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. and lspci -v gave me: 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Hewlett-Packard Company Device 1483 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at 52000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

  Read the article

• Two Wifi Icons in Panel

  - by Alex

  I have the exact problem in 13.10 as this user Two Wifi indicators in panel. Here are some screenshots: Here are some screenshots from another user: http://ubuntuforums.org/showthread.php?t=2183020&p=12825563 ifconfig and iwconfig outputs $ ifconfig lo Link encap:Local Loopback inet addr:XXXXXX Mask:XXXXXXX inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2243 errors:0 dropped:0 overruns:0 frame:0 TX packets:2243 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:209889 (209.8 KB) TX bytes:209889 (209.8 KB) wlan0 Link encap:Ethernet HWaddr XXXXXXXXX inet addr:XXXXXX Bcast:XXXXXXXX Mask:XXXXXXX inet6 addr: XXXXXXX Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5925 errors:0 dropped:0 overruns:0 frame:0 TX packets:3361 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2951818 (2.9 MB) TX bytes:630579 (630.5 KB) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"XXXXX" Mode:Managed Frequency:2.437 GHz Access Point: XXXXXXXX Bit Rate=72.2 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:153 Invalid misc:472 Missed beacon:0

  Read the article

• WiFi on Ubuntu 12.04 custom: downloading unbearably slow

  - by Mark

  iwconfig reports 11 Mbps, yet I've seen as low as <1 KBps. This is the latest in my laundry list of Ubuntu problems in a dual-boot machine (cyberpowerpc custom, intel i7-3820, nvidia gtx 570). I received it two days ago, Windows 7 running fine, still having problems with Ubuntu. The browsing is intermittent but unacceptable. e.g. I could get to this site last night but I couldn't post this question. The downloading is unbearably slow, I can't download anything or install any packages because the speed is so slow. e.g. I am trying to install vim which is inexplicably missing from my 12.04 install (add another one to the problems list) and my download speed reported in the terminal was 241 B/s. Yes, bytes. iwconfig reports 11 Mbps, which further adds to the confusion. User@ubuntu:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:39:76:2C:A1 Bit Rate=11 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=36/70 Signal level=-74 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:54 Invalid misc:18 Missed beacon:0 eth0 no wireless extensions. Any ideas? I see this is a problem a lot of people, but none of the on line solutions have worked for me so far. e.g. one site recommends editing the ath9k.conf file in /etc/modprobe.d, yet this file isn't even in the folder: User@ubuntu:/$ cd etc/modprobe.d User@ubuntu:/etc/modprobe.d$ ls alsa-base.conf blacklist-oss.conf blacklist-ath_pci.conf blacklist-rare-network.conf blacklist.conf blacklist-watchdog.conf blacklist-firewire.conf dkms.conf blacklist-framebuffer.conf nvidia-current_hybrid.conf blacklist-modem.conf nvidia-graphics-drivers.conf I think the nvidia gpu might be mucking things up. I had the "blinking cursor" problem when installing in the first place, and then I had the monitor out of range problem as well. I have my faithful Asus laptop, which is running Ubuntu 12.04 just fine. The only difference is executing host -t SOA local in the terminal gives User@ubuntu:~$ host -t SOA local local has SOA record local. nobody.localhost. 42 86400 43200 604800 10800 in my new machine, and the command reports Host local. not found in the laptop. Help would be most welcome, as I am in danger of reverting back to Windows. I'm seriously considering it. Sorry for the length, trying to show my effort in resolving the issue and include terminal snippets that might be helpful.

  Read the article

• Ubuntu Server 12.04, Wifi problems

  - by brievolz84

  When I installed Ubuntu Server 12.04, I selected the ethernet adapter because I will use that most often; however, I would like to use wifi sometimes as well. This is how far I've gotten with this problem. lspci 02:00.0 Network Controller: Intel Corporation PRO/Wireless 5100 AGN [Shiloh] Network Connection iwconfig wlan0 IEEE a/b/g/n BSSID=off/any Mode=Managed Access Point=Not-Associated TX-Power=off Retry Long Limit:7 RTS thr:off Fragment thr:off Power Management:off I tried to do iwconfig wlan0 up but that doesn't work either. The error message said something along the lines of rfkill but I'm not connected to the Internet to download that particular program. Any help here would be great

  Read the article

• Connect to WEP Wireless Network by command line on Ubuntu

  - by Tim

  Hi, I am a newbie to both network and Linux. I am now trying to connect to a WEP wireless network by command line on my Ubuntu 8.10, because the Network Manager does not support 64 bit WEP. (1) I firstly bring down the Network Manager and then try to connect to a wireless network, whose essid is candy and password is 5673212741. But it fails as shown in the following. I wonder why and how to do it correctly? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwconfig wlan0 essid candy opendo iwconfig wlan0 key 18018ce78e open $ sudo iwconfig wlan0 key 5673212741 open $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 9971 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 20 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 13 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9 No DHCPOFFERS received. No working leases in persistent database - sleeping. $ ping www.bbc.co.uk ping: unknown host www.bbc.co.uk (2) A less important question: why the scan for wireless networ does not work after I bring down the Network Manager? $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo iwlist wlan0 scan wlan0 Interface doesn't support scanning : Network is down Thanks and regards!

  Read the article

• Can't enable wireless lan on Fujitsu Siemens A1665G with Ubuntu 11.10 installed

  - by Theo

  I saw my old Notebook yesterday and wanted to make that work again. On Windows XP the wireless worked still fine. Then I installed new Ubuntu 11.10 32bit and I'm sadly not able to make the wireless enabled. [I replaced Win XP entirely] lspci lists following network: 08:0a.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) So after recommendation from this link I installed the b43 firmware module. iwconfig prints the following: wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associatd Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management: off As you can see, my wireless lan adapter is not turned on. sudo iwconfig wlan0 txpower auto Doesn't change anything. Then I tried to make it work with rfkill. rfkill list 0: phy0: Wirless LAN Soft blocked: no Hard blocked: yes sudo rfkill unblock all rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes remains the same. The question is now, how I could enable the hard blocked wireless LAN. There is no hardware switch for wlan integrated. However there is a button to change the state. I always thought this would be software sided, but it seems to make some hardware changes as well... The wireless LED is also not blinking (as it did on windows xp) I reset bios and searched for some settings in there, but it has only a few options and nothing to do with wireless settings, nothing works here.. At last I tried to install the acer hotkeys but I was not able to manage that. I installed the acerhkgui package, but in initializing progress, it was not able to compile acer hotkeys for my machine. There was a message that asm/linkage.h was not found while compiling. Do you have any ideas what I could do to make this hard blocked stuff disabled and my wireless card work? PS: I also tried sudo rm /dev/rfkill and a reboot to reinit that stuff... No success :(

  Read the article

• Troubleshooting wireless network connectivity

  - by taserian

  I'm currently running Ubuntu 10.10, and I'm running into trouble keeping my wireless connection alive. After rebooting, I get about 5-10 minutes of a good speed connection; afterwards, the connection just zeroes out. I've gotten around to stirring up a shell script that gives me another 10 minutes or so of connectivity. Script contents below: #! /bin/bash sudo ifconfig wlan0 up echo "Enabling wireless device . . ." sleep 5 sudo iwconfig wlan0 essid MyNetworkName echo "Connecting to network. . ." sleep 10 sudo dhclient wlan0 echo "Getting IP address. . ." sleep 5 echo "Done. Closing window. . ." sleep 5 Shortly after running the line "sudo iwconfig wlan0 essid MyNetworkName" from the script, I notice the speed pick up. Other computers in my home running Windows XP are not affected by this problem, so all indications point to my Ubuntu machine. Does anyone have any pointers as to how to resolve this?

  Read the article

• Connecting to wireless networks from command line

  - by Balaji

  I need to write a shell script which connects to one of the two available wi-fi connections. One is a un secure connection and the other is secure connection. My question has 2 parts- 1.How to connect to the un-secure (un-encrypted and no password required) connection from command line (or by executing a shell script) when I'm connected to the secure connection? I followed the steps in http://www.ubuntugeek.com/how-to-troubleshoot-wireless-network-connection-in-ubuntu.html for in-secure connection. I put all the commands in a script and executed it (I made sure that interface name and essid are correct) - sudo dhclient -r wlan0 - sudo ifconfig wlan0 up - sudo iwconfig wlan0 essid "UAPublic" - sudo iwconfig wlan0 mode Managed - sudo dhclient wlan0 But nothing happens - I'm not disconnected from the current network and connected to the new one 2.When I want to connect to the secure wi-fi network, I understand from http://askubuntu.com/a/138476/70665 that I need to use wpa_supplicant. But I enter a lot of details in the interface when I connect via UI security : wpa and wpa2 enterprise Authentication : PEAP CA certificate : Equifax... PEAP version : automatic inner authentication : MSCHAPv2 username : password : How to use wpa_supplicant to mention all these details in the command line? The conf file network={ ssid="ssid_name" psk="password" } doesn't work for me.

  Read the article

• Making bash script to check connectivity and change connection if necessary. Help me improve it?

  - by cypherpunks

  My connection is flaky, however I have a backup one. I made some bash script to check for connectivity and change connection if the present one is dead. Please help me improve them. The scripts almost works, except for not waiting long enough to receive an IP (it cycles to next step in the until loop too quick). Here goes: #!/bin/bash # Invoke this script with paths to your connection specific scripts, for example # ./gotnet.sh ./connection.sh ./connection2.sh until [ -z "$1" ] # Try different connections until we are online... do if eval "ping -c 1 google.com" then echo "we are online!" && break else $1 # Runs (next) connection-script. echo fi shift done echo # Extra line feed. exit 0 And here is an example of the slave scripts: #!/bin/bash ifconfig wlan0 down ifconfig wlan0 up iwconfig wlan0 key 1234567890 iwconfig wlan0 essid example sleep 1 dhclient -1 -nw wlan0 sleep 3 exit 0

  Read the article

• RealTek RTL8188CE WiFi adapter doesn't connect reliably

  - by ken.ganong

  I recently bought a new system76 laptop which came pre-installed with Ubuntu 11.10. I've been having trouble with my wireless connectivity. It seems that my connection with my wireless network keeps going in and out. It is not my network--I have seen the same problem on multiple WiFi networks and at different distances and reported link qualities. OS version: Ubuntu 11.10 oneiric kernel version: 3.0.0-14-generic lspci: lspci -nnk | grep -iA2 net 04:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:9196] Kernel driver in use: rtl8192ce -- 05:00.0 Ethernet controller [0200]: JMicron Technology Corp. JMC250 PCI Express Gigabit Ethernet Controller [197b:0250] (rev 05) Subsystem: CLEVO/KAPOK Computer Device [1558:2500] Kernel driver in use: jme iwconfig: iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"peppermintpatty" Mode:Managed Frequency:2.462 GHz Access Point: 98:FC:11:6C:E0:22 Bit Rate=72.2 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Power Management:off Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:1103 Missed beacon:0 lshw: sudo lshw -class network *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 00:1c:7b:a1:95:04 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.0.0-14-generic firmware=N/A ip=192.168.1.106 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:18 ioport:e000(size=256) memory:f7d00000-f7d03fff *-network description: Ethernet interface product: JMC250 PCI Express Gigabit Ethernet Controller vendor: JMicron Technology Corp. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 00:90:f5:c0:42:b3 size: 10Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm pciexpress msix msi bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=jme driverversion=1.0.8 duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:56 memory:f7c20000-f7c23fff ioport:d100(size=128) ioport:d000(size=256) memory:f7c10000-f7c1ffff memory:f7c00000-f7c0ffff Any help would be appreciated. The last time I've dealt with wireless issues, the most given solution was NDIS wrapper and I seem sorely out-of-date.

  Read the article

• Getting WLAN on my Laptop to work (Medion MD98300)

  - by Anand Böhmer

  Dear Ubuntu Community, I am having difficulties to get the WLAN Adapter on my Medion 98300 Laptop to work. The WLAN Card seems to be connected through an internal USB Interface and the Card itself had shown up as a wirelles Network while installing Ubuntu. I have tried a few things earlier, but none of my google reasearches have brought me to a working solution... I am quite new to the Linux System and only knoew a couple of terminal commands so far, so I probably have missed out on a few possible solutions. Maybe you can help me? Thank you very much in advance! A fre minimal technical Details: AMD Turion 64 X2 Dual-Core Mobile Technolgie TL-50 NVIDIA GeForce Go 6150 SanDisk 64GB SSD 2GB RAM DDR2 667 nForce Chipset (I forgt the Version, but deductable from the GPU I guess) WiFi: ZyDAS ZD1211B 802.11g Thank's a lot again! :) UPDATE: I tried around myself a little and found a guide on the Linux Mint forums that helped! I already had tried to install the linux backport modules etc. What I finally did was update the linux firmware and run the following command: echo "options acer_wmi wirelles=1" sudo tee /etc/modprobe.d/acer_wmi.conf and rebooted now I found and could connect to networks, but unfortunately I found, that the link quality was very bad, around 40 to 50. Eventhough my Router is running at high power and is only 6 Meters away! I then switched a few channels, but that did not improve much. Before, under Windows, I had a very good link quality and had the entire 16mbit/s internet connection at disposal, now I can only get about 3-5Mbit/s. better then nothing, but still pretty bad! The "TX power" is fixed on 20dBm and iwconfig says, that the "Power Management" is off... Maybe the power of the module is set too low?... UPDATE2: I figured that 20dBm is a normal power output. I even tried to change the power using iwconfig wlan0 txpower INTEGERHERE but, obviously my "Card" does not support more then 20. More would probably be illegal as well, so I won't even use more then 20. I guess that I will have to figure out a way, or maybe just switch cards. Are the Mailboard-USB-Connectors on a laptop of the same property as the standard external ones? If so, I could simply solder a micro Wirelless N Adapter onto the board :)

  Read the article

1 2 3 4 5 6 7  | Next Page >