Search Results

Search found 168 results on 7 pages for 'iwconfig'.

Page 3/7 | < Previous Page | 1 2 3 4 5 6 7  | Next Page >

• slow speed transfering files to a local network device

  - by F. Ariel Jung

  I'm having troubles copying files from my pc(ubuntu 13.04 64 bits) to a Media Center(WDTV Live: with an SATA2 HDD attached) through the local network. the speed is to slow, it's up to 2.0 MB/s image: http://s11.postimg.org/g1nuai92b/Captura_de_pantalla_de_2013_06_24_07_46_55.png (I don't use image tag because it is a big image) my PC has a wifi network card Tp Link TL-WN951N and it is connected to a TP Link TL-WDR3500 router via wifi, and the WDTV Live is connected via LAN here is a iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TL-WDR3500" Mode:Managed Frequency:2.462 GHz Access Point: A0:F3:C1:6C:3B:F1 Bit Rate=39 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:33521 Invalid misc:2245290 Missed beacon:0 if more data is required I'll post it as needed. I can't figure this out, needed help. please

  Read the article

• WIFI card intel r 2200 will not work

  - by Telemarkhero

  I have installed 12.04 on a Fujitsu Siemens Amilo Pro. Wifi card does not work. Have tried various threads but none have the same problem. Think I have the correct firmware but the following comes up: gill@ubuntu:~$ iwconfig lo no wireless extensions. eth1 IEEE 802.11bg ESSID:off/any Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power=off Sensitivity=8/0 Retry limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 eth0 no wireless extensions. Also gill@ubuntu:~$ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes There is a power switch for wifi but it does not do anything in Ubuntu. Any pointers greatfully received.

  Read the article

• Broadcom 4365 wireless driver on 12.04 with 3.4 / 3.5 kernel

  - by zaid

  I used this package to install the driver on 3.2 Kernel and it was working perfectly. Unfortunately the system used to freeze randomly with 3.2 kernel so I installed 3.4 kernel, now there is no freezing, the only problem is that my wifi card is not working, I tried to re-install the package, but didn't work. I can see the driver in the "additional drivers" and it say that it is active, but when I execute iwconfig it doesn't show up. I've even tried ndiswraper and that didn't work either. my lspci: 01:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01)

  Read the article

• How to fix slow wireless with Intel 4965 AGN? [closed]

  - by mikewhatever

  Possible Duplicate: Slow wireless with an Intel 4965 We run Ubuntu 12.04, 32bit, with the current kernel 3.2.27-generic on an MSI EX700. I've already added the 11n_disable=1 tweek, without whcih, wireless has been unusable. Now, it works OK, but speedtest shows: Windows XP - down 11.68mbps, up 2.07mbps Ubuntu 12.04 - down 2.06mbps up 2.0mbps We've disabled ipv6, tried static and dinamic IPs, tried both swcrypto=0 and swcrypto=1 options, none of whcih made any difference. The problem may be the symptom of high packet loss. For example, here's the output of iwconfig after booting and testing the speeds: wlan0 IEEE 802.11abg ESSID:"amu" Mode:Managed Frequency:2.462 GHz Access Point: 00:78:9E:FA:32:C8 Bit Rate=54 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=58/70 Signal level=-52 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:11 Invalid misc:3627 Missed beacon:0 I've posted a help request before with lots of technical info and outputs.

  Read the article

• What software is responsible for connecting to the wireless net specified in /etc/network/interfaces?

  - by zuba

  I'm curious what software (package, utility in bin's) handle interface parameters in /etc/network/interfaces and decides to connect to the specified wireless net. I use wifi usb stick dlink DWL-110 attached to wlan0 with ndiswrapper driver. Sometimes wlan0 sees my wifi net - iwlist wlan0 scan shows it, but does not connect to it - iwconfig shows AP Not-Associated, until I replug the stick. Neither reinserting module with ndiswrapper, not ifdown/ifup or restarting networking helps. That is why I need to know what OS entity handles connection/reconnection to wireless net. EDIT: shame on me, I use wireless-tool package with wep encryption

  Read the article

• Wireless Not Working with Drivers Installed

  - by Haoran

  I'm new to Linux. I installed Ubuntu 12.10 on my old Compaq/Hp Preario V3000 to replace Windows XP. Every thing works fine except I'm getting no wireless network options in the network drop down menu. I'm using a cable at the moment. Wirless chipset is: 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) 08:08.0 Ethernet controller: Intel Corporation PRO/100 VE Network Connection (rev 02) I ran rfkill: 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no I also ran iwconfig and got this lo no wireless extensions. eth0 no wireless extensions. In the additional drivers it says: "Using Broadcom 802.11 Linux STA wireless driver source from bcmwl-kernel-source (proprietary)" Any help to resolve the problem would be greatly appreciated.

  Read the article

• Wireless problems on HP

  - by Sat93

  I'm not able to enable Wireless using the hardware switch on my HP ProBook4430s. Because of this the Enable Wireless option is greyd out and I cannot enable it. The greyd out option can be seen in the screenshot below. The results of iwconfig for my system are as follows, lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. Also I tried to do the following, sudo ifconfig wlan0 up but I got an error as below, SIOCSIFFLAGS: Operation not possible due to RF-kill Also the result of sudo rfkill list all for my system is as follows, 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: hp-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no How do I fix this problem? Thanku!

  Read the article

• Installing Broadcom Wireless Drivers

  - by Fer1805

  I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. What are the steps to install Broadcom wireless drivers for a BCM43xx card? I'm a user with no advance knowledge in Linux, so I would need clear explanations on how to make, compile, etc. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] iwconfig showed: lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• D-Link DWA-125 Wireless network card not working after upgrade from 10.04 to 12.04

  - by dava2788

  I upgraded to Ubuntu 12.04 and now the wireless network card D-Link DWA-125 doesn't work. I have the drivers from the official website, But neither recognized during installation. iwconfig: lo no wireless extensions. vmnet8 no wireless extensions. ra0 Ralink STA Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. vmnet1 no wireless extensions. dava@Dava-Ubuntu:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 006: ID 07d1:3c0d D-Link System DWA-125 Wireless N 150 Adapter(rev.A1) [Ralink RT3070] And the chipset: ralink 2870/3070 (rt3070)

  Read the article

• knetworkmanager not starting at all

  - by yoshi

  It seems that my knetworkmanager is not starting anymore. Read: In KDE4's sys tray I don't have a icon to manage my networks. Also when starting it from terminal or kick off menu literally "nothing" happens. I don't know what's wrong with it. Sadly after reading this answer on superuser.com it seems I can not connect to wifi via iwconfig 'cause my network is WPA2 encrypted. (Basically I can not set they passphrase - invalid argumenterror.) So it seems I've to get knetworkmanger running again as I also can't download other tools. I've tried stuff like sudo service network-manager restart but it didn't seem to help. I'm kinda puzzled so any help for this would be appreciated. PS: If it hasn't become clear: The whole drama of is simply I can't connect to wifi and internet :o)

  Read the article

• Wireless access through command line interface

  - by hfranco

  Is there a CLI command or program that will list available wireless access points? I'm running Ubuntu 9.04 on a laptop and sometimes I boot straight into the CLI instead of a GUI. I know iwconfig can configure a connection but will not list available AP's.

  Read the article

• unable to sniff traffic despite network interface being in monitor or promiscuous mode

  - by user65126

  I'm trying to sniff out my network's wireless traffic but am having issues. I'm able to put the card in monitor mode, but am unable to see any traffic except broadcasts, multicasts and probe/beacon frames. I have two network interfaces on this laptop. One is connected normally to 'linksys' and the other is in monitor mode. The interface in monitor mode is on the right channel. I'm not associated with the access point because, as I understand, I don't need to if using monitor mode (vs promiscuous). When I try to ping the router ip, I'm not seeing that traffic show up in wireshark. Here's my ifconfig settings: daniel@seasonBlack:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:29:9e:b2:89 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8518 (8.5 KB) TX bytes:8518 (8.5 KB) wlan0 Link encap:Ethernet HWaddr 00:21:00:34:f7:f4 inet addr:192.168.1.116 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:ff:fe34:f7f4/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:9758 errors:0 dropped:0 overruns:0 frame:0 TX packets:4869 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3291516 (3.2 MB) TX bytes:677386 (677.3 KB) wlan1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-33-34-00-00-00-00-00-00-00-00 UP BROADCAST NOTRAILERS PROMISC ALLMULTI MTU:1500 Metric:1 RX packets:112754 errors:0 dropped:0 overruns:0 frame:0 TX packets:101 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:18569124 (18.5 MB) TX bytes:12874 (12.8 KB) wmaster0 Link encap:UNSPEC HWaddr 00-21-00-34-F7-F4-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster1 Link encap:UNSPEC HWaddr 00-02-72-7B-92-53-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Here's my iwconfig settings: daniel@seasonBlack:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:"linksys" Mode:Managed Frequency:2.437 GHz Access Point: 00:18:F8:D6:17:34 Bit Rate=54 Mb/s Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=68/70 Signal level=-42 dBm Noise level=-69 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 wmaster1 no wireless extensions. wlan1 IEEE 802.11bg Mode:Monitor Frequency:2.437 GHz Tx-Power=27 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Here's how I know I'm on the right channel: daniel@seasonBlack:~$ iwlist channel lo no frequency information. eth0 no frequency information. wmaster0 no frequency information. wlan0 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6) wmaster1 no frequency information. wlan1 11 channels in total; available frequencies : Channel 01 : 2.412 GHz Channel 02 : 2.417 GHz Channel 03 : 2.422 GHz Channel 04 : 2.427 GHz Channel 05 : 2.432 GHz Channel 06 : 2.437 GHz Channel 07 : 2.442 GHz Channel 08 : 2.447 GHz Channel 09 : 2.452 GHz Channel 10 : 2.457 GHz Channel 11 : 2.462 GHz Current Frequency=2.437 GHz (Channel 6)

  Read the article

• 13.10 - Weird WiFi connection problems - WMP300N - Broadcom BCM4321

  - by user1898041

  Just installed 13.10 on my desktop and I really like it. After having problems with getting the wifi to work, I installed it connected to the internet with an ethernet cable and added in the 3rd party software and updates as per the installation procedure. After installation was completed, I saw the wifi icon in the upper right hand corner, but it was not seeing any wifi networks. Some Googling brought me to use the 'Additional Drivers' application. It found the WMP300N Broadcom BDM4321 based pci wifi card and installed the proprietary Broadcom STA wireless driver, which may have been installed before. I'm not sure. Here is the weird part: when I start my system, wifi seems to be in some sort of suspended state where the system sees that the card exists but the card will not detect any wifi networks. It will work after booting once I 'Additional Drivers' application and then start FireFox. I know it seems weird, but this is the process I've got down to get the card to recognize wifi networks. After those applications are open for a few seconds, the card starts to function like normal (although maintaining the wifi connection is problem but most likely a seperate issue). The reason this is a problem is because this is supposed to just be a headless box managed through SSH. Here are the readouts from the common network diagnosis programs BEFORE I open 'Additional Drivers' and 'FireFox'. All commands were done with sudo. lspci 00:00.0 Host bridge: Intel Corporation 82G35 Express DRAM Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 82G35 Express PCI Express Root Port (rev 03) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 01:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 220] (rev a2) 01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1) 02:00.0 Ethernet controller: Qualcomm Atheros Attansic L1 Gigabit Ethernet (rev b0) 03:00.0 IDE interface: JMicron Technology Corp. JMB368 IDE controller 05:00.0 Network controller: Broadcom Corporation BCM4321 802.11b/g/n (rev 01) 05:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) - lshw *-network description: Ethernet interface product: Attansic L1 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: b0 serial: 00:22:15:00:a8:12 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1 driverversion=2.1.3 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:feac0000-feafffff memory:feaa0000-feabffff *-network description: Wireless interface product: BCM4321 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 00:23:69:d8:2b:16 width: 32 bits clock: 33MHz capabilities: bus_master ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) latency=64 multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:febfc000-febfffff - ifconfig eth0 Link encap:Ethernet HWaddr 00:22:15:00:a8:12 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:23:69:d8:2b:16 inet6 addr: fe80::223:69ff:fed8:2b16/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:24 errors:0 dropped:0 overruns:0 frame:0 TX packets:24 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1856 (1.8 KB) TX bytes:1856 (1.8 KB) - iwconfig eth1 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=200 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off - iwlist scan eth1 No scan results - Here are the various commands AFTER I open 'Additional Drivers' and 'FireFox' lspci 00:00.0 Host bridge: Intel Corporation 82G35 Express DRAM Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 82G35 Express PCI Express Root Port (rev 03) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) 00:1c.4 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 (rev 02) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 02) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IR (ICH9R) LPC Interface Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6 port SATA Controller [AHCI mode] (rev 02) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) 01:00.0 VGA compatible controller: NVIDIA Corporation GT216 [GeForce GT 220] (rev a2) 01:00.1 Audio device: NVIDIA Corporation High Definition Audio Controller (rev a1) 02:00.0 Ethernet controller: Qualcomm Atheros Attansic L1 Gigabit Ethernet (rev b0) 03:00.0 IDE interface: JMicron Technology Corp. JMB368 IDE controller 05:00.0 Network controller: Broadcom Corporation BCM4321 802.11b/g/n (rev 01) 05:03.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6306/7/8 [Fire II(M)] IEEE 1394 OHCI Controller (rev c0) - lshw *-network description: Ethernet interface product: Attansic L1 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: b0 serial: 00:22:15:00:a8:12 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1 driverversion=2.1.3 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:feac0000-feafffff memory:feaa0000-feabffff *-network description: Wireless interface product: BCM4321 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: 01 serial: 00:23:69:d8:2b:16 width: 32 bits clock: 33MHz capabilities: bus_master ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.30.223.141 (r415941) ip=192.168.1.103 latency=64 multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:febfc000-febfffff - ifconfig eth0 Link encap:Ethernet HWaddr 00:22:15:00:a8:12 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr 00:23:69:d8:2b:16 inet addr:192.168.1.103 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:69ff:fed8:2b16/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:85 errors:0 dropped:0 overruns:0 frame:11901 TX packets:132 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:52641 (52.6 KB) TX bytes:19058 (19.0 KB) Interrupt:16 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:76 errors:0 dropped:0 overruns:0 frame:0 TX packets:76 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6084 (6.0 KB) TX bytes:6084 (6.0 KB) - iwconfig eth1 IEEE 802.11abg ESSID:"BU" Mode:Managed Frequency:2.447 GHz Access Point: 00:26:F2:1F:81:02 Bit Rate=54 Mb/s Tx-Power=200 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=59/70 Signal level=-51 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 - iwlist scan A LOT OF SSIDs FOUND! - I'd like to have this problem fixed, but I'm not quite sure where to go. Been Googling a lot and can't seem to find anyone else with this problem.

  Read the article

• Unable to connect to Wireless after installing Ubuntu 12.10

  - by Moulik

  I am using Asus U56E laptop and after installing Ubuntu 12.10 alongside Windows 8, I am unable to connect to the Wireless. I have been trying to solve this problem since two weeks and couldn't solve it. Please help. Any answer would be appreciated. Here are some command-line results. lspci -v | grep -iA 7 network ubuntu@ubuntu:~$ lspci -v | grep -iA 7 network 02:00.0 Network controller: Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Subsystem: Intel Corporation Centrino Wireless-N + WiMAX 6150 BGN Flags: bus master, fast devsel, latency 0, IRQ 52 Memory at de800000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi lsmod | grep iwlwifi ubuntu@ubuntu:~$ lsmod | grep iwlwifi iwlwifi 386826 0 mac80211 539908 1 iwlwifi cfg80211 206566 2 iwlwifi,mac80211 ubuntu@ubuntu:~$ dmesg | grep iwlwifi [ 57.846261] iwlwifi: Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [ 57.846264] iwlwifi: Copyright(c) 2003-2012 Intel Corporation [ 57.846336] iwlwifi 0000:02:00.0: >pci_resource_len = 0x00002000 [ 57.846338] iwlwifi 0000:02:00.0: >pci_resource_base = ffffc90000c7c000 [ 57.846341] iwlwifi 0000:02:00.0: >HW Revision ID = 0x67 [ 57.846438] iwlwifi 0000:02:00.0: >irq 52 for MSI/MSI-X [ 59.558335] iwlwifi 0000:02:00.0: >loaded firmware version 41.28.5.1 build 33926 [ 59.558514] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUG disabled [ 59.558516] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEBUGFS enabled [ 59.558517] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TRACING enabled [ 59.558519] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_DEVICE_TESTMODE enabled [ 59.558520] iwlwifi 0000:02:00.0: >CONFIG_IWLWIFI_P2P disabled [ 59.558522] iwlwifi 0000:02:00.0: >Detected Intel(R) Centrino(R) Wireless-N + WiMAX 6150 BGN, REV=0x84 [ 59.558583] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 59.569083] iwlwifi 0000:02:00.0: >device EEPROM VER=0x557, CALIB=0x6 [ 59.569085] iwlwifi 0000:02:00.0: >Device SKU: 0x150 [ 59.569087] iwlwifi 0000:02:00.0: >Valid Tx ant: 0x1, Valid Rx ant: 0x3 [ 59.569100] iwlwifi 0000:02:00.0: >Tunable channels: 13 802.11bg, 0 802.11a channels [ 70.208469] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.208648] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 [ 70.366319] iwlwifi 0000:02:00.0: >L1 Disabled; Enabling L0S [ 70.366470] iwlwifi 0000:02:00.0: >Radio type=0x1-0x2-0x0 sudo lshw -c network ubuntu@ubuntu:~$ sudo lshw -c network *-network description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 67 serial: 40:25:c2:84:99:c4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.5.0-17-generic firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:de800000-de801fff *-network description: Ethernet interface product: AR8151 v2.0 Gigabit Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c0 serial: 54:04:a6:2b:6a:ef capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:54 memory:dd400000-dd43ffff ioport:a000(size=128) ifconfig ubuntu@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 54:04:a6:2b:6a:ef UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:176 errors:0 dropped:0 overruns:0 frame:0 TX packets:176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:14368 (14.3 KB) TX bytes:14368 (14.3 KB) wlan0 Link encap:Ethernet HWaddr 40:25:c2:84:99:c4 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) iwconfig ubuntu@ubuntu:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off iwlist scan ubuntu@ubuntu:~$ iwlist scan eth0 Interface doesn't support scanning. lo Interface doesn't support scanning. wlan0 No scan results nm-tool ubuntu@ubuntu:~$ nm-tool NetworkManager Tool State: disconnected - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 54:04:A6:2B:6A:EF Capabilities: Carrier Detect: yes Wired Properties Carrier: off - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: disconnected Default: no HW Address: 40:25:C2:84:99:C4 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points hypeness2: Infra, 00:21:29:DA:08:4F, Freq 2462 MHz, Rate 54 Mb/s, Strength 42 WPA love: Infra, 68:7F:74:17:02:66, Freq 2412 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 DIRECT-MwSCX-3400Pamela: Infra, 02:15:99:A3:3F:AC, Freq 2412 MHz, Rate 54 Mb/s, Strength 22 WPA2 router: Infra, 1C:AF:F7:D6:76:F3, Freq 2417 MHz, Rate 54 Mb/s, Strength 20 WPA2 wing: Infra, E8:40:F2:34:E4:F7, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 132LINKSYS: Infra, 00:1A:70:80:1F:E9, Freq 2437 MHz, Rate 54 Mb/s, Strength 57 WEP VMITTAL: Infra, E0:46:9A:3C:F0:C4, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 WEP HP-Print-10-LaserJet 1025: Infra, 7C:E9:D3:7E:F8:10, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 ACNBB: Infra, 00:26:75:22:A6:2F, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 SATKAIVAL: Infra, 00:18:E7:CE:69:A6, Freq 2412 MHz, Rate 54 Mb/s, Strength 69 WPA WPA2 hypeness: Infra, B8:E6:25:24:C3:B1, Freq 2437 MHz, Rate 54 Mb/s, Strength 54 WPA WPA2 CSNetwork: Infra, BC:14:01:58:C5:88, Freq 2437 MHz, Rate 54 Mb/s, Strength 25 WPA WPA2 tharma: Infra, BC:14:01:E2:06:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 15 WPA WPA2 Active2.4: Infra, 10:6F:3F:0E:F3:8E, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 ACNBB: Infra, 00:26:75:58:4E:7A, Freq 2437 MHz, Rate 54 Mb/s, Strength 85 KO: Infra, BC:14:01:2E:AF:A8, Freq 2452 MHz, Rate 54 Mb/s, Strength 22 WPA WPA2 FEAR: Infra, 00:18:4D:C0:BC:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA Pamela: Infra, BC:14:01:52:F6:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 24 WPA WPA2 bvrk2: Infra, 78:CD:8E:7B:3C:79, Freq 2457 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 BELL030: Infra, D8:6C:E9:17:AF:09, Freq 2462 MHz, Rate 54 Mb/s, Strength 22 WPA2 Desai: Infra, 00:1D:7E:52:FB:C5, Freq 2437 MHz, Rate 54 Mb/s, Strength 14 WEP Sritharan: Infra, BC:14:01:E5:59:78, Freq 2462 MHz, Rate 54 Mb/s, Strength 19 WPA WPA2 PFN: Infra, 00:13:10:8B:CF:45, Freq 2437 MHz, Rate 54 Mb/s, Strength 19 WEP rfkill list all ubuntu@ubuntu:~$ rfkill list all 0: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: asus-wimax: WiMAX Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no so these are some more results sudo modprobe -r iwlwifi ubuntu@ubuntu:~$ sudo modprobe -r iwlwifi sudo modprobe iwlwifi 11n_disable=1 ubuntu@ubuntu:~$ sudo modprobe iwlwifi 11n_disable=1 echo "blacklist asus_wmi" | sudo tee -a /etcmodprobe.d/blacklist.conf ubuntu@ubuntu:~$ echo "blacklist asus_wmi" | sudo tee -a /etc/modprobe.d/blacklist.conf blacklist asus_wmi echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf ubuntu@ubuntu:~$ echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi ubuntu@ubuntu:~$ sudo modprobe -rfv iwlwifi rmmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko sudo modprobe -v iwlwifi ubuntu@ubuntu:~$ sudo modprobe -v iwlwifi insmod /lib/modules/3.5.0-17-generic/kernel/net/wireless/cfg80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/net/mac80211/mac80211.ko insmod /lib/modules/3.5.0-17-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko 11n_disable=1

  Read the article

• How to configure wireless in gentoo?

  - by Absolute0

  I have a single access point which i want to connect to on interface ra0, when I run /etc/init.d/ra0 restart I get the following output: gentoo ~ # /etc/init.d/net.ra0 restart * Starting ra0 * Configuring wireless network for ra0 Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" Error for wireless request "Set Encode" (8B2A) : SET failed on device ra0 ; Network is down. * ra0 does not support setting keys * or the parameter "mac_key_roswell" or "key_roswell" is incorrect Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" * WEP key is not set for "BAY_WiFi" - not connecting * Couldn't associate with any access points on ra0 * Failed to configure wireless for ra0 when I run iwlist ra0 scan I get "roswell" and "bay-wifi" I want to connect to only roswell. Here is my /etc/conf.d/net: modules= ( "iwconfig" ) key_roswell="ffff-ffff-ff" # no s: means a hex key preferred_aps=( "roswell" ) what am i doing wrong?

  Read the article

• How to configure wireless in gentoo?

  - by Absolute0

  I have a single access point which i want to connect to on interface ra0, when I run /etc/init.d/ra0 restart I get the following output: gentoo ~ # /etc/init.d/net.ra0 restart * Starting ra0 * Configuring wireless network for ra0 Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" Error for wireless request "Set Encode" (8B2A) : SET failed on device ra0 ; Network is down. * ra0 does not support setting keys * or the parameter "mac_key_roswell" or "key_roswell" is incorrect Error for wireless request "Set Mode" (8B06) : SET failed on device ra0 ; Network is down. * ra0 does not support setting the mode to "managed" * WEP key is not set for "BAY_WiFi" - not connecting * Couldn't associate with any access points on ra0 * Failed to configure wireless for ra0 when I run iwlist ra0 scan I get "roswell" and "bay-wifi" I want to connect to only roswell. Here is my /etc/conf.d/net: modules= ( "iwconfig" ) key_roswell="ffff-ffff-ff" # no s: means a hex key preferred_aps=( "roswell" ) what am i doing wrong?

  Read the article

• ndiswrapper wlan driver installed, but wlan still does not work

  - by mugetsu

  I'm trying to get my Atheros AR1111 EB-WG PCI wireless adapter to work. Right now wifi is not even detected. I'm on ubuntu 12.04 64bit and I managed to find a xp64bit driver. I followed the exact steps here: https://help.ubuntu.com/community/WifiDocs/Driver/Ndiswrapper And where I do ndiswrapper -l I get something like : {name of driver} : driver installed device ({Chipset ID}) present which shows that the driver installed properly However, after I load the new module : sudo modprobe ndiswrapper nothing happens, and iwconfig shows that I still have no wlan. I tried to do dmseg | grep ndiswrapper, but there were no driver loading errors or anything strange. I also have blacklist ath5k, ath8k in /etc/modprobe.d/blacklist.conf What am I doing wrong? What could be causing this?

  Read the article

• Can't set-up Wifi Adhoc on my Raspberry Pi with an USB dongle

  - by Wouter

  I am trying to set-up an access point (ad-hoc) for my Raspberry Pi. That means I'm trying to "share" the ethernet connection over Wi-Fi. I am doing this using my Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter. When following a tutorial (or actually every tutorial), it immediately goes wrong. root@pinkypi:/home/pi# iwconfig wlan0 mode ad-hoc Error for wireless request "Set Mode" (8B06) : SET failed on device wlan0 ; Device or resource busy. I already tried ifdown and not having it in the USB port at the startup. If it helps, every action with the thing fail (or at least setting the mode). I am using Debian. I'm sure I'm overseeing something, but I can't find out what. What is wrong?

  Read the article

• How to know my wireless card has injection enabled?

  - by shrimpy

  I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

  Read the article

• Rate limit a wireless interface

  - by Jamie Hankins

  I have access to my routers SSH and IPTables. I want to rate limit my guest network to 1Mb/s so they can't guzzle my bandwidth. rai1 RTWIFI SoftAP ESSID:"GuestNetwork" Nickname:"" Mode:Managed Channel=6 Access Point: :F9 Bit Rate=300 Mb/s wdsi0 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: :F8 Bit Rate=300 Mb/s wdsi1 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: :F9 Bit Rate=300 Mb/s wdsi2 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: Not-Associated Bit Rate:300 Mb/s wdsi3 RTWIFI SoftAP ESSID:"YouCan'tTouchThis" Nickname:"" Mode:Managed Channel=6 Access Point: Not-Associated Bit Rate:300 Mb/s I'm just wondering the command I need to limit it. I tried the iwconfig limit command but it failed. Thanks

  Read the article

• How do you add a certificate for WLAN in Linux, at the command-line?

  - by Neil

  I'm using Maemo on a Nokia n810 Internet tablet, and when given a list of installed certificates to choose from when connecting to a PEAP wireless network, it's always blank. I've already installed a couple of certificates through the gui on the device, and only the certificate authorities show up. I've confirmed that Maemo's connection software that handles certificates is buggy, in such a way that certificates are never added, or properly added certificates cannot be found. Is there a way to add WLAN certificates at the command-line, and connect to a wireless network at the command-line as well? I used to use iwconfig to connect, but I never used it with PEAP. Note: I have nothing in /etc/ssl/certs

  Read the article

• How do you add a certificate for WLAN in Linux, at the command-line?

  - by Neil

  I'm using Maemo on a Nokia n810 Internet tablet, and when given a list of installed certificates to choose from when connecting to a PEAP wireless network, it's always blank. I've already installed a couple of certificates through the gui on the device, and only the certificate authorities show up. I've confirmed that Maemo's connection software that handles certificates is buggy, in such a way that certificates are never added, or properly added certificates cannot be found. Is there a way to add WLAN certificates at the command-line, and connect to a wireless network at the command-line as well? I used to use iwconfig to connect, but I never used it with PEAP. Note: I have nothing in /etc/ssl/certs

  Read the article

• strange behaviour - dhclient needs to be run twice in order to connect to wireless

  - by splicer

  I am trying to connect my to my wlan without the use of NetworkManager. I run the following commands after boot: iwconfig wlan0 enc <WEP passwd> mode managed essid <name> channel 6 ifconfig wlan0 up dhclient wlan0 At this point, dhclient stalls for ages (perhaps 2 minutes), then it returns with PING 192.168.1.254 (192.168.1.254) from 192.168.1.65 wlan0: 56(84) bytes of data. --- 192.168.1.254 ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3000ms pipe 3 .. The strange thing is that when I run pkill dhclient; dhclient wlan0 right after this, it connects in about <3 seconds. Any idea what could be the cause of this problem? Edit: oh, and I did try using the -timeout flag on dhclient but that didn't seem to make any difference (it still stalled for ages).

  Read the article

• b43 module loaded, but no interface showed up

  - by Eduardo Bezerra

  I'm using CentOS 6.3 x86_64 on a hardware with a BCM43224 chip for wi-fi. I installed the b43-fwcutter module and then run modprobe b43, with no error messages. However, no new network interface showed up, and the return of iwconfig is: lo no wireless extensions. eth0 no wireless extensions. lspci -nn | grep 43224 returns: 03:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) and uname -a: Linux localhost.localdomain 2.6.32-279.14.1.el6.x86_64 #1 SMP Tue Nov 6 23:43:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Any ideas of how to make the wireless device work?

  Read the article

• Wireless router not connection -> AP Not associated

  - by candido

  I can not connect to internet by wireless router after some months with ubuntu 10.04. I can connect with the same portable but with win OS. My SO is ubuntu 10.04 linux 2.6.32-41 arch SMP i686. The internet wireless network controller is Atheros AR9285 chipset (pci express) Kernel module ath9k I have tried a command line connection: $ sudo /etc/init.d/network-manager stop #stop gui network manager $ iwconfig wlan0 essid WLAN_3C key s:C001D20550B3C $ ifconfig Access Point: NOT-ASSOCIATED $dmesg ... AP 00:1a:2b:08:60:49 associated Is the SO has connected to router for booting long ( associated message), after boot and login why the connection to router is not possible by network-manager or command line (NOT associated message)? Thanks in advance

  Read the article

< Previous Page | 1 2 3 4 5 6 7  | Next Page >