Search Results

Search found 2591 results on 104 pages for 'dell powervault'.

Page 10/104 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

• Dell Inspiron 1520 Intermittent connection to wireless router

  - by ChuckNevol

  I have two computers in my home which are connected to a wireless router and a wireless printer. One computer is a Del XPS and the other a Dell laptop Inspiron 1520. In recent weeks we noticed the Inspiron had difficulty maintaining connection to the wireless router - web pages would suddenly have to be reloaded, or the computer rebooted while the other computer, the XPS, had no problems on the same network. So we connected a hard wire line from the Inspiron to the Verizon supplied wireless router. Problems still exist. could it be a bad driver?

  Read the article

• Beep code for Dell Poweredge T105

  - by Thomas

  I can't start my Poweredge T-105 just after two years. It does not display any on monitor but blue lights on 3 & 4 of system case. And it repeatedly beeps. At first, it beeps 1-3-3 and then repeats 1-1-3-4. As far as I can search on the net, Dell's beep code is 3 digit. So do I have to consider the beep code for my error is 1-3-3? Unfortunately, my warranty expired last year so any hint will be appreciated.

  Read the article

• Dell Latitude e6520 gaming capabilities?

  - by user1072185

  I am purchasing a very reduced Dell Latitude e6520 from a friend and was wondering what kinds of games I could play on it and what resolutions. I'm not buying it for gaming purposes, but I am curious. The specs are as follows: Intel® Core™ i7-2720QM (2.20GHz, 6M cache) with Turbo BoostTechnology 2.0 nVidia® NVS™ 4200M 512MB DDR3 Discrete Graphics for Quad Core upon further research, the CPU requires this graphic card. 4.0GB, DDR3-1333MHz SDRAM 500GB 7200rpm Hard Drive I may upgrade to 8GB memory, depending if I am bogged down, what do you guys think?

  Read the article

• dell poweredge 860 always pxe boot

  - by Berto

  Hi, We bought a dell poweredge 860, and installed windows server 2008 std. So far so good. Now everytime the server reboots, it try's the pxe boot, and hangs on "cant find pxe bootable, press f1 to continue or f2 to setup". Now, i tried all the settings in the bios (it's the latest - A05), i have the nic active without pxe (i also tried with the nic off)... well, i tried everyting off and on the bios and it still goes to pxe booting. I have one sata drive, that is boot's after the f1. I would like to keep the system updated, but i can't because of the reboot, can someone point me to some direction? Can i give any more information of the server? If yes, what do you want? It has been a week on google trying to figure out this one. Thx

  Read the article

• Laptop battery liftime from Dell specs?

  - by user26535

  Question: When I buy a Dell Laptop, I get the following choice for battery: (Lithium-Ion main battery with X cells and Y Wh [included in price/at additional $] Lithium-Ionen-Hauptakku mit 4 Zellen und 24 Wh [Im Preis enthalten] Lithium-Ionen-Hauptakku mit 9 Zellen und 85 Wh [zuzgl. CHF 120.01] Lithium-Ionen-Hauptakku mit 6 Zellen und 46 Wh [zuzgl. CHF 30.00 I figured that I can calculate that a 86 Wh offers +254% of the 24 Wh lifetime, but... Is there any way to calculate to what battery time this amounts in hours ? I mean how many hours will the 24 Wh last (at normal operation - eg. writing a document - not watching video), else the +254% is a pretty useless number... Also anybody knows whether 4 cells means 4 times 24 Wh, or 24 Wh in total?

  Read the article

• Function keys on Dell laptop work double as OEM keys

  - by Factor Mystic

  I'm working with a new Dell Studio 1555, and the F1-F12 keys at the top of the keyboard are dual function with OEM keys such as volume and screen brightness. The problem is, is that the OEM keys are the default, and you have to press the Fn key to get the F- key to work. For example, this means you have to hit Alt+Fn+F4 to close a window, instead of the regular Alt+F4. This is really annoying. Is there a way to reverse the default functions of the F- keys in Windows? Ideally this is possible without some kind of third party hotkey manager.

  Read the article

• Resizing RAID 1 Array on Dell PowerEdge with Perc 4/Di & Windows SBS 2003

  - by Scott McKinney

  I have a Dell PowerEdge 2600 with Perc 4/Di RAID card and Windows SBS 2003 installed. The original system drive was a set of 17GB drives in a RAID 1 array. Over the years, these drives have failed (individually) and been replaced by a set of 73GB drives, but the RAID array is still 17GB in size. Is there a safe procedure to resize the RAID 1 array to use the entire 73GB without destroying/corrupting the data on the array? The Perc documentation mentions a Reconstruct option with Online Capacity Expansion, but is a woefully short on the exact details. Has anyone performed this procedure successfully (or unsuccessfully)? What were the steps? Are there any gotchas I should watch out for?

  Read the article

• Remote Access Problems with DRAC 5 on Dell PowerEdge 1950

  - by Darin Peterson

  Today I received my first Dell PowerEdge 1950 server with a DRAC 5 card. On my local network I have static configurations on my Linux systems using this for instance: iface eth0 inet static address 192.168.1.210 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 8.8.8.8 8.8.4.4 For the DRAC card, I configured the LAN like this: address 192.168.1.215 netmask 255.255.255.0 gateway 192.168.1.1 For the advanced LAN settings I used dns-nameservers 8.8.8.8 8.8.4.4 I've tried many different IP addresses, but cannot communicate with the card. Is there anyone who might know if I have configuration issues, or maybe if the card might be bad?

  Read the article

• off-the-shelf HDD in Dell Optiplex 755 - Invalid Replacement - Press F1 when rebooting

  - by Eric Liprandi

  Hi, I recently put an SSD into my work Optiplex 755. Since then, every time the system boots or reboots, I get prompted to hit F1 to continue with a message like HDD replacement is not valid. The system works just fine. What I am gathering from Dell's website is that I left the original drive internally as a data drive. And apparently the Optiplex does not support 2 drives in the configuration we purchased originally and complains. Any suggestions on how to get rid of this message? some suggested the MEBx or whatever from Intel and to turn it off, but I did not succeed earlier. It's not a big deal 80% of the time, but I regularly work from home and occasionally need to fire a reboot and well, you don't get the BIOS screen remotely :) Regards, Eric.

  Read the article

• Dedicated GPU in Dell PowerEdge C1100

  - by Eli Gundry

  We recently purchased a Dell PowerEdge C1100 off lease with the initention of using it for graphics processing. We installed an AMD HD 7000 series GPU in it that runs off of board power and it sends video to the display. That said, the video is very choppy, leading us to belive that the onboard video is doing all the processing and sending it to the card. Is there any way to either disable the VGA on this server or tell the OS to only use the dedicated card. More info: The server is running REHL 6.4 The graphics running the proprietary AMD drivers The video card only works in OS and does not show the BIOS on boot (we know that it's impossible to change this) Any ideas, guys? Update We are now thinking that the GPU is doing the graphics processing, but not working at the full speed of the PCI bus. Which is odd, because it is an x16 slot, but probably optimized to use a RAID card (if that makes any sense). Is there any way to remedy the choppy graphics on this server?

  Read the article

• off-the-shelf HDD in Dell Optiplex 755 - Invalid Replacement - Press F1 when rebooting

  - by Eric Liprandi

  I recently put an SSD into my work Optiplex 755. Since then, every time the system boots or reboots, I get prompted to hit F1 to continue with a message like HDD replacement is not valid. The system works just fine. What I am gathering from Dell's website is that I left the original drive internally as a data drive. And apparently the Optiplex does not support 2 drives in the configuration we purchased originally and complains. Any suggestions on how to get rid of this message? some suggested the MEBx or whatever from Intel and to turn it off, but I did not succeed earlier. It's not a big deal 80% of the time, but I regularly work from home and occasionally need to fire a reboot and well, you don't get the BIOS screen remotely :) Regards, Eric.

  Read the article

• Dell SC1435 always requires F1 at boot

  - by David Mackintosh

  I have a Dell PowerEdge SC1435 that has come back after doing duty at a partner site. I am trying to configure it for local use. The only problem I have with it is that every time it boots it always requres a manual F1 press after the POST sequence. The last thing it does is give me the opportunity to configure the BMC, and then it says: Press F1 to continue or press F2 for Setup It will wait there forever (well, at least an hour). Pressing F1 starts the OS booting. I can't see the setting in the BIOS which controls this and I can't find it in the documentation. What am I missing?

  Read the article

• Dell Dimension 2400 problem

  - by murgatroid99

  I have a new problem with a Dell Dimension 2400 PC. Until yesterday or the day before, it was working fine, but today when I press the power button the light on the power button turns yellow instead of green, the fan behind the processor increases speed until it sounds like a jet engine, and the computer does not boot up. I cleaned out the dust in the computer so that is not the problem. Also, the fan was blowing cold air. Do any of you know what might be causing this and how I might be able to fix it?

  Read the article

• Very slow disk performance on Dell PowerEdge 2950 w/ PERC 6/i running RAID 10

  - by vocoder

  I recently set up a server running Ubuntu 10.04 LTS on a Dell PowerEdge 2950 server - it has 6 500 gb 7200RPM SATA drives setup in a RAID 10 config. I am seeing extremely poor disk performance - the RAID array reports all disks are normal and using MegaCLI, it looks like the BBU is fine. hdparm -tT /dev/sda reports: Timing cached reads: 90 MB in 2.05 seconds = 43.96 MB/sec Timing buffered disk reads: 24 MB in 3.11 seconds = 7.72 MB/sec So as you can see, it takes forever to something as simple as an apt-get upgrade and even logging into the server. How do I go about troubleshooting what is causing this? I upgraded the firmware on the PERC 6i RAID controller to the latest, but didn't see any improvements.

  Read the article

• Getting packets from one port to another on a Dell PowerConnect 2824 switch

  - by Arvo Bowen

  I have a dell PowerConnect 2824 and I have a cat 5 cable connected from port 1 to port 23. Port 1 is reserved for VLAN 1 (the only VLAN that can manage the switch) and port 18-23 belong to VLAN 112. I currently have the switch setup with ip 10.71.3.5/27 and a test machine plugged into port 22 with IP address 10.71.3.30/27. For some reason I can not ping 10.71.3.5 from my test machine (10.71.3.30). Note: When I try to ping the server plugged into port 21 (IP: 10.71.3.7/27) also VLAN 112, I get responses just fine. Note: When I plug my test machine directly into port 1, I can ping 10.71.3.5 just fine. Quick Recap: Switch IP: 10.71.3.5 Port 1 - dedicated to management - (VLAN1) Port 21 - SERVER (10.71.3.7/27) - (VLAN112) Port 22 - test machine (10.71.3.30/27) - (VLAN112) Port 23 - dedicated to management (to hop over to VLAN 1 from VLAN 112) - (VLAN112)

  Read the article

• How to set up Dell OMSA tools on Debian 6 (Squeeze) (PE2950)

  - by javano

  I assume I have set up them up incorrectly or am missing a library or dependency. When I log into the OMSA web interface I can't see anything Also, omreport tells me nothing; root@box:~# omreport storage controller No controllers found I assume these two will use the same source of information so what ever is wrong will fix them both. I set up OMSA as per these instructions. Also I have compiled MegaCLI (as this is a PowerEdge 2950 with a Perc 6/i controller) and I have used that to update the RAID firmware, so that works, but the Dell tools aren't. What have I missed during set up? root@kvm1:~# cat /etc/issue Debian GNU/Linux 6.0 \n \l root@kvm1:~# uname -a Linux kvm1.mivoice.cust.vostron.net 3.4.9 #1 SMP Wed Aug 22 19:08:46 BST 2012 x86_64 GNU/Linux

  Read the article

• Removing RAID on a DELL power-edge server

  - by Simon Callan

  We have a Dell Power-edge T110 server, with either a PERC S100 or S300 raid controller (I suspect S100), and 2 x 500GB SATA hard discs. These discs are running in RAID-1 configuration, (either 1 or 2 virtual discs), and on top of this, we have the C and D drives. As we are running low on disc space, we are looking at dropping the RAID to get some disc space back. Is it possible to split the discs back into 2 seperate hards discs that the OS can see, without losing all the data on the drives? Even better, would it be possible to split the D: drive, leaving the OS C: drive in RAID1 configuration?

  Read the article

• Dell poweredge 1850's - wont install os

  - by user1326789

  I have 3 of these dell 1850 rack servers. 1 has 3GB RAM and 2 73GB HDD's. 2 have 6GB RAM and each of them has 2 73GB HDD's. I am currently trying to install an os on them but when i boot with windows xp setup, it gives me an error saying no partition found. Now i have set these drives up in RAID on the server and i put them "online" so it should be working fine but they're not. Please assist me in installing an operating system on these, i have no clue as to if it's the BIOS or the RAID controller within it. Thanks in advance, -Matt.

  Read the article

• Installing W2K8 R2 on a Dell Poweredge 2850

  - by DerekT

  I'm a server novice and have been given a Dell 2850 (PERC 4e/Di). It has 3 blank HDs that I think are configured as RAID 5. I am trying to install W2K8 R2 SP1 on it. It doesn't have a DVD reader so I created an install USB. This works fine until it's time to copy files to the HD. It can't see a HD. There is an option to browse for drivers at this stage. Any idea what drivers I need and where to download them? I downloaded this driver RAID_DRVR_WIN_R227150.EXE but this failed with invalid signature. Thanks to dyasny for the link to LSI-LOGIC_MULTI-DEVICE_A00_R227150.exe.

  Read the article

• Dell U271 monitor DisplayPort suddenly not working

  - by Amir Latif

  My new(ish) Dell U271 took a bit of a knock and it now suddenly doesn't recognise the Macbook plugged into it via DisplayPort - this had been working great for several months up until now. When I "Scan Sources", it doesn't find anything on DisplayPort. However, one suspicious behaviour leads me to think all might not be lost. When the Mac is woken from sleep, this used to kick the monitor in (as an monitor would) and while it no longer does that, the light on the monitor does go from standby orange to blue briefly, then the monitor says it's going into "power save" mode. It seems like it gets some kinda signal. Any ideas on how I can diagnose the problem? I'm trying to find another mac but no one near me has one ...

  Read the article

• Dell 620 display is too bright to use

  - by keith

  I have a Dell D620 with a display problem. In windows 7 the display seems to be too bright, the text is broken up, the only way to see the mouse is at a very oblique angle. Changing the brightness with fn and brightness control has little/no effect. When I put it in high contrast mode I can see all the colors, but any windows pictures etc are still useless. I cannot get it to connect to an external monitor via VGA port or via a USB-VGA connector.

  Read the article

• dell vostro 1310 with nVidia 8400M display problem

  - by Arthur

  Hi everyone, i hope someone can help me with this problem. I have a Dell vostro 1310 Laptop with 32 bit vista and a 8400M nVidia chip. Recently i have noticed performance issues when my girlfriend was playing Sims 3, and then one day i turned it on and all i got was a thick white line at the bottom of the screen. i heard the OS start up so automatically i thought it was a damaged screen, but i had doubts so i plugged it into an external display via the vga port. it worked but everything appart worm the OS choice menu looks distorted beyond belief. even the bios screen had multicoloured lines running down the screen. The resolution is non existant, the screen only shows a 256 colour pallette and is heavily distorted. i barely managed to get to the device manager where i found the gfx card with an exclamation mark. does anybody have suggestions? should i buy a new mobo or are repairs possible? thanks in advance

  Read the article

• Dell EqualLogic vs. EMC VNXe [closed]

  - by Untalented

  We've been looking into SMB SANs and based on the competitive pricing I've been getting we're really liking these two array's. There are some pro's to both solutions, but I've unable to really decide which to choose. The EMC offers better expandability since you can buy an additional shelf (roughly $1200) and can add drives then to the array. However, the Dell unit is still very nice. Can anyone comment on their experiences with the two and thoughts on this? Also, to get the VMware Storage API support you need VMware Enterprise. How much additional performance does this provide? It's roughly $15k more than the Essentials Plus bundle we're looking at (this is a small environment [3 Hosts 1 Array].

  Read the article

• Dell Studio XPS 16 Runs Hot

  - by dtbarne

  Specs: 1920x1080 i7 1.6 GHz quad core 6GB RAM 1GB ATI Radeon HD 6570M/5700 Series 500GB 7200rpm Hard Drive Love this laptop for many reasons, but it constantly runs hot (CPU is low 70s with basic tasks and often 80+ is not uncommon) and I'm finding it too much to deal with. The laptop feels very hot (almost too hot for a lap) and often gets so hot that the OS slows down or freezes altogether. I've tried cleaning it out and even replacing the thermal paste. I often use an external cooler, but it only helps 3-5 degrees and it's a pain to have to use. I've come to the conclusion that it just runs hot. I have two questions: What is to blame? The i7 processor, the gfx card, or is it just that this laptop has poor cooling? Does the Dell XPS 15 run cooler? I'm looking at replacing my current laptop, but I don't want to run into the same problem.

  Read the article

• Dell docking station / Windows 7 not detecting HannsG JC199D via DVI

  - by user27150

  I have a laptop running Win7 that I use with a Dell docking station. I'd used it with XP for a couple years running dual monitors from the docking station, one from the VGA and one from the DVI. After upgrading to Win7, the monitor that's on the DVI out is not detected, using "rigorous detection" or otherwise. I've switched the cables to verify that it's not the monitor at fault-- but I can't find any info on why the monitor wouldn't be detected. I've got the latest and greatest Nvidia drivers installed (at least, as far as Windows update is aware). Leaving the laptop lid partly open does allow Windows to detect the laptop's native screen as well as the VGA monitor, but never the DVI. The monitors are HannsG JC199Ds. Any ideas? Thanks!

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >