Search Results

Search found 1073 results on 43 pages for 'firmware'.

Page 10/43 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

• very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

  - by gojira

  I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

  Read the article

• Freshly installed dd-wrt on dir-300 and no internet. What to do?

  - by Erik B

  With the d-link firmware I just connected the router and it worked, as is expected when using DHCP, but with dd-wrt I have no internet access. It is configured with DHCP, and dd-wrt's wan status page reports that it is connected and that it has an ip address. Yet it is impossible to reach the internet. If I disconnect the router and plugs the cable directly into my computer I get internet access, so it's obviously the dd-wrt software that isn't doing its job. However, I have no previous experience with the dd-wrt software and have no clue what to look for. I thought it would just work. By the way, the power led is orange, the internet led is off, and wireless+lan1 is green. They all used to be green with the d-link firmware. Not sure if it's relevant, but now you know. Does anyone have any idea what I should do to get internet access (besides reinstalling d-link's firmware)? EDIT: It's a version B1. I read that it is very different from the A1 version, so I thought it may be relevant.

  Read the article

• Cisco RV042 VPN with Dynamic IPs - Remote Gateway Not Resolving

  - by Rister

  I have an existing network setup that I inherited from my predecessor. Currently there are two sites, each with a Linksys RV042 VPN router running the 1.3.12.19-tm firmware. They are currently set up with a Gateway to Gateway VPN. One site has a static IP, the other has a Dynamic IP with a hostname set up on no-ip.com. My company is looking to set up another site so I purchased another RV042 only this one was Cisco branded and it is running the latest firmware. I had assumed that I would be able to configure a vpn from our main office (the dynamic ip) to the new site with this router quite easily. However when I set up a new VPN tunnel on either device, it stays on Waiting for Connection and the Remote Gateway shows an ip address of 0.0.0.0 rather than the remote ip address. The other VPN tunnel is still working and I don't see any obvious misconfiguration on the new router. It seems that the router is not resolving the Dynamic DNS address and therefore not giving me the option to connect the VPN. Does a Gateway to Gateway VPN work with Dynamic IP addresses on each end? Are the firmware versions not compatible? Is there something I've missed?

  Read the article

• RAID-capable 3.5" SATA Drives

  - by nroam

  I recently purchased a pair of 1TB Western Digital WD1002FBYS RE3 drives for use in an external RAID enclosure. I have found that they tend to drop out of the array after a while. Thinking it was the enclosure I tried them on another one but found the same issue. So a bit of googling and I found http://www.tomshardware.com/forum/251076-32-raid-issues-western-digital-hard-disk which suggests that: "WD's "RE" (RAID Edition) HDDs support Time-Limited Error Recovery ("TLER" ): http://www.wdc.com/en/products/productcatalog.asp?language=en As a non-TLER HDD fills up with data, the error detection firmware might take too long, and the RAID controller may drop that HDD from a RAID array." So now I wonder what SATA drives have firmware which is compatible with RAID arrays (esp. RAID 1, 5, but not 0)? I have not been able to come up with the magic set of keywords to ellicit the answer from Google. However, various sites suggest that Seagate & Hitachi are in general OK. Does anyone have any generic (or even specific) guidance on how to work out if a drive's firmware may harbour code that is potentially an issue in a RAID0 setting other than stating that it must be 'enterprise' ready?

  Read the article

• wii programming

  - by harald

  hello, my daughter just got a wii for christmas from her parents and her father has nothing better to do than looking for ways to dive into wii programming. i already read a lot about "homebrew" and wii. but i seem to be unable to find answers for the most important questions: do i have to modify the firmware to get the homebrew stuff to work? how likely is it, that the wii get's bricked, if for example there are any nintendo firmware updates? thanks very much!

  Read the article

• How To Make iPhone App For Multiple Firmwares

  - by Dyldo42

  With iOS4 coming out soon, I have already planned to include an iAd in a future update of an app of mine. I assume that this will make my app unusable for anyone on a firmware lower than 4.0. Is there a way to change that variables and the .xib file based on the user's firmware? Cheers.

  Read the article

• Lenovo V570 CPU fan running constantly, CPU core 1 running over 90%!

  - by Rabbit2190

  I have seen that a lot of people are having this same issue. I am running a Lenovo V570 i5 4 core, 6 gigs of ram, and am running 11.10 Onieric Ocelot. On my system monitor graph it shows CPU at 20%, when I open the monitor it shows core #1 at around 90%, the other cores fluctuate at or below 5-12% if even. Now this seems like a really terrible balance of power between the cores, especially with so much stress on one core only, when these things are designed to work with 4 cores and not at such high temps. My current readings say 64 degrees Celsius, this does not seem normal for any cpu, and I am seriously considering, working on my windows7 partition until I see a real solution to this issue or upgrading to 12.04 right away when it comes out... I have seen countless things saying it has something to do with the Kernel, the kernel on mine is the same as when I upgraded, I really do not like messing with it, as when I had 11.04, I did tinker with it due to the freeze issues I was having, and that just made worse issues. I like this version 11.10 and would like to keep it for a while, but without the fear that my core is going to fry! So any help would be much appreciated! I did try changing a couple things in ACPI, and restarting this did not help, and here I am. I tried one thing prior to that that was listed under a different computer brand, but it would not do a make on the file. I really need help with this, I rely on this computer for a lot of things, and love this OS! Please help so I do not need to resort to my Microsoft partition! PLEASE! Here is the fwts cpufrequ- output: rabbit@rabbit-Lenovo-V570:~$ sudo fwts cpufreq - 00001 fwts Results generated by fwts: Version V0.23.25 (Thu Oct 6 15 00002 fwts :12:31 BST 2011). 00003 fwts 00004 fwts Some of this work - Copyright (c) 1999 - 2010, Intel Corp. 00005 fwts All rights reserved. 00006 fwts Some of this work - Copyright (c) 2010 - 2011, Canonical. 00007 fwts 00008 fwts This test run on 02/04/12 at 17:23:22 on host Linux 00009 fwts rabbit-Lenovo-V570 3.0.0-17-generic-pae #30-Ubuntu SMP Thu 00010 fwts Mar 8 17:53:35 UTC 2012 i686. 00011 fwts 00012 fwts Running tests: cpufreq. 00014 cpufreq CPU frequency scaling tests (takes ~1-2 mins). 00015 cpufreq --------------------------------------------------------- 00016 cpufreq Test 1 of 1: CPU P-State Checks. 00017 cpufreq For each processor in the system, this test steps through 00018 cpufreq the various frequency states (P-states) that the BIOS 00019 cpufreq advertises for the processor. For each processor/frequency 00020 cpufreq combination, a quick performance value is measured. The 00021 cpufreq test then validates that: 00022 cpufreq 1) Each processor has the same number of frequency states 00023 cpufreq 2) Higher advertised frequencies have a higher performance 00024 cpufreq 3) No duplicate frequency values are reported by the BIOS 00025 cpufreq 4) Is BIOS wrongly doing Sw_All P-state coordination across cores 00026 cpufreq 5) Is BIOS wrongly doing Sw_Any P-state coordination across cores 00027 cpufreq Frequency | Speed 00028 cpufreq -----------+--------- 00029 cpufreq 2.45 Ghz | 100.0 % 00030 cpufreq 2.45 Ghz | 83.7 % 00031 cpufreq 2.05 Ghz | 69.2 % 00032 cpufreq 1.85 Ghz | 62.5 % 00033 cpufreq 1.65 Ghz | 55.2 % 00034 cpufreq 1400 Mhz | 48.6 % 00035 cpufreq 1200 Mhz | 41.8 % 00036 cpufreq 1000 Mhz | 34.5 % 00037 cpufreq 800 Mhz | 27.6 % 00038 cpufreq 9 CPU frequency steps supported 00039 cpufreq Frequency | Speed 00040 cpufreq -----------+--------- 00041 cpufreq 2.45 Ghz | 97.7 % 00042 cpufreq 2.45 Ghz | 83.7 % 00043 cpufreq 2.05 Ghz | 69.6 % 00044 cpufreq 1.85 Ghz | 63.3 % 00045 cpufreq 1.65 Ghz | 55.7 % 00046 cpufreq 1400 Mhz | 48.7 % 00047 cpufreq 1200 Mhz | 41.7 % 00048 cpufreq 1000 Mhz | 34.5 % 00049 cpufreq 800 Mhz | 27.5 % 00050 cpufreq Frequency | Speed 00051 cpufreq -----------+--------- 00052 cpufreq 2.45 Ghz | 97.7 % 00053 cpufreq 2.45 Ghz | 84.4 % 00054 cpufreq 2.05 Ghz | 69.6 % 00055 cpufreq 1.85 Ghz | 62.6 % 00056 cpufreq 1.65 Ghz | 55.9 % 00057 cpufreq 1400 Mhz | 48.7 % 00058 cpufreq 1200 Mhz | 41.7 % 00059 cpufreq 1000 Mhz | 34.7 % 00060 cpufreq 800 Mhz | 27.8 % 00061 cpufreq Frequency | Speed 00062 cpufreq -----------+--------- 00063 cpufreq 2.45 Ghz | 100.0 % 00064 cpufreq 2.45 Ghz | 82.6 % 00065 cpufreq 2.05 Ghz | 67.8 % 00066 cpufreq 1.85 Ghz | 61.4 % 00067 cpufreq 1.65 Ghz | 54.9 % 00068 cpufreq 1400 Mhz | 48.3 % 00069 cpufreq 1200 Mhz | 41.1 % 00070 cpufreq 1000 Mhz | 34.3 % 00071 cpufreq 800 Mhz | 27.4 % 00072 cpufreq Frequency | Speed 00073 cpufreq -----------+--------- 00074 cpufreq 2.45 Ghz | 96.2 % 00075 cpufreq 2.45 Ghz | 82.5 % 00076 cpufreq 2.05 Ghz | 69.3 % 00077 cpufreq 1.85 Ghz | 62.7 % 00078 cpufreq 1.65 Ghz | 55.0 % 00079 cpufreq 1400 Mhz | 47.4 % 00080 cpufreq 1200 Mhz | 41.1 % 00081 cpufreq 1000 Mhz | 34.0 % 00082 cpufreq 800 Mhz | 27.2 % 00083 cpufreq Frequency | Speed 00084 cpufreq -----------+--------- 00085 cpufreq 2.45 Ghz | 96.5 % 00086 cpufreq 2.45 Ghz | 83.6 % 00087 cpufreq 2.05 Ghz | 68.1 % 00088 cpufreq 1.85 Ghz | 61.7 % 00089 cpufreq 1.65 Ghz | 54.9 % 00090 cpufreq 1400 Mhz | 48.0 % 00091 cpufreq 1200 Mhz | 41.1 % 00092 cpufreq 1000 Mhz | 34.2 % 00093 cpufreq 800 Mhz | 27.8 % 00094 cpufreq Frequency | Speed 00095 cpufreq -----------+--------- 00096 cpufreq 2.45 Ghz | 96.4 % 00097 cpufreq 2.45 Ghz | 82.6 % 00098 cpufreq 2.05 Ghz | 68.8 % 00099 cpufreq 1.85 Ghz | 60.5 % 00100 cpufreq 1.65 Ghz | 52.4 % 00101 cpufreq 1400 Mhz | 48.8 % 00102 cpufreq 1200 Mhz | 41.1 % 00103 cpufreq 1000 Mhz | 34.2 % 00104 cpufreq 800 Mhz | 26.4 % 00105 cpufreq Frequency | Speed 00106 cpufreq -----------+--------- 00107 cpufreq 2.45 Ghz | 95.3 % 00108 cpufreq 2.45 Ghz | 82.5 % 00109 cpufreq 2.05 Ghz | 65.5 % 00110 cpufreq 1.85 Ghz | 62.8 % 00111 cpufreq 1.65 Ghz | 54.8 % 00112 cpufreq 1400 Mhz | 48.0 % 00113 cpufreq 1200 Mhz | 41.2 % 00114 cpufreq 1000 Mhz | 34.2 % 00115 cpufreq 800 Mhz | 27.3 % 00116 cpufreq Frequency | Speed 00117 cpufreq -----------+--------- 00118 cpufreq 2.45 Ghz | 96.3 % 00119 cpufreq 2.45 Ghz | 83.4 % 00120 cpufreq 2.05 Ghz | 68.3 % 00121 cpufreq 1.85 Ghz | 61.9 % 00122 cpufreq 1.65 Ghz | 54.9 % 00123 cpufreq 1400 Mhz | 48.0 % 00124 cpufreq 1200 Mhz | 41.1 % 00125 cpufreq 1000 Mhz | 34.2 % 00126 cpufreq 800 Mhz | 27.3 % 00127 cpufreq Frequency | Speed 00128 cpufreq -----------+--------- 00129 cpufreq 2.45 Ghz | 100.0 % 00130 cpufreq 2.45 Ghz | 77.9 % 00131 cpufreq 2.05 Ghz | 64.6 % 00132 cpufreq 1.85 Ghz | 54.0 % 00133 cpufreq 1.65 Ghz | 51.7 % 00134 cpufreq 1400 Mhz | 45.2 % 00135 cpufreq 1200 Mhz | 39.0 % 00136 cpufreq 1000 Mhz | 33.1 % 00137 cpufreq 800 Mhz | 25.5 % 00138 cpufreq Frequency | Speed 00139 cpufreq -----------+--------- 00140 cpufreq 2.45 Ghz | 93.4 % 00141 cpufreq 2.45 Ghz | 75.7 % 00142 cpufreq 2.05 Ghz | 64.5 % 00143 cpufreq 1.85 Ghz | 59.1 % 00144 cpufreq 1.65 Ghz | 51.4 % 00145 cpufreq 1400 Mhz | 45.9 % 00146 cpufreq 1200 Mhz | 39.3 % 00147 cpufreq 1000 Mhz | 32.7 % 00148 cpufreq 800 Mhz | 25.8 % 00149 cpufreq Frequency | Speed 00150 cpufreq -----------+--------- 00151 cpufreq 2.45 Ghz | 92.1 % 00152 cpufreq 2.45 Ghz | 78.1 % 00153 cpufreq 2.05 Ghz | 65.7 % 00154 cpufreq 1.85 Ghz | 58.6 % 00155 cpufreq 1.65 Ghz | 52.5 % 00156 cpufreq 1400 Mhz | 45.7 % 00157 cpufreq 1200 Mhz | 39.3 % 00158 cpufreq 1000 Mhz | 32.7 % 00159 cpufreq 800 Mhz | 24.3 % 00160 cpufreq Frequency | Speed 00161 cpufreq -----------+--------- 00162 cpufreq 2.45 Ghz | 88.9 % 00163 cpufreq 2.45 Ghz | 79.8 % 00164 cpufreq 2.05 Ghz | 58.4 % 00165 cpufreq 1.85 Ghz | 52.6 % 00166 cpufreq 1.65 Ghz | 46.9 % 00167 cpufreq 1400 Mhz | 41.0 % 00168 cpufreq 1200 Mhz | 35.1 % 00169 cpufreq 1000 Mhz | 29.1 % 00170 cpufreq 800 Mhz | 22.9 % 00171 cpufreq Frequency | Speed 00172 cpufreq -----------+--------- 00173 cpufreq 2.45 Ghz | 92.8 % 00174 cpufreq 2.45 Ghz | 80.1 % 00175 cpufreq 2.05 Ghz | 66.2 % 00176 cpufreq 1.85 Ghz | 59.5 % 00177 cpufreq 1.65 Ghz | 52.9 % 00178 cpufreq 1400 Mhz | 46.2 % 00179 cpufreq 1200 Mhz | 39.5 % 00180 cpufreq 1000 Mhz | 32.9 % 00181 cpufreq 800 Mhz | 26.3 % 00182 cpufreq Frequency | Speed 00183 cpufreq -----------+--------- 00184 cpufreq 2.45 Ghz | 92.9 % 00185 cpufreq 2.45 Ghz | 79.5 % 00186 cpufreq 2.05 Ghz | 66.2 % 00187 cpufreq 1.85 Ghz | 59.6 % 00188 cpufreq 1.65 Ghz | 52.9 % 00189 cpufreq 1400 Mhz | 46.7 % 00190 cpufreq 1200 Mhz | 39.6 % 00191 cpufreq 1000 Mhz | 32.9 % 00192 cpufreq 800 Mhz | 26.3 % 00193 cpufreq FAILED [MEDIUM] CPUFreqCPUsSetToSW_ANY: Test 1, Processors 00194 cpufreq are set to SW_ANY. 00195 cpufreq FAILED [MEDIUM] CPUFreqSW_ANY: Test 1, Firmware not 00196 cpufreq implementing hardware coordination cleanly. Firmware using 00197 cpufreq SW_ANY instead?. 00198 cpufreq 00199 cpufreq ========================================================= 00200 cpufreq 0 passed, 2 failed, 0 warnings, 0 aborted, 0 skipped, 0 00201 cpufreq info only. 00202 cpufreq ========================================================= 00204 summary 00205 summary 0 passed, 2 failed, 0 warnings, 0 aborted, 0 skipped, 0 00206 summary info only. 00207 summary 00208 summary Test Failure Summary 00209 summary ==================== 00210 summary 00211 summary Critical failures: NONE 00212 summary 00213 summary High failures: NONE 00214 summary 00215 summary Medium failures: 2 00216 summary cpufreq test, at 1 log line: 193 00217 summary "Processors are set to SW_ANY." 00218 summary cpufreq test, at 1 log line: 195 00219 summary "Firmware not implementing hardware coordination cleanly. Firmware using SW_ANY instead?." 00220 summary 00221 summary Low failures: NONE 00222 summary 00223 summary Other failures: NONE 00224 summary 00225 summary Test |Pass |Fail |Abort|Warn |Skip |Info | 00226 summary ---------------+-----+-----+-----+-----+-----+-----+ 00227 summary cpufreq | | 2| | | | | 00228 summary ---------------+-----+-----+-----+-----+-----+-----+ 00229 summary Total: | 0| 2| 0| 0| 0| 0| 00230 summary ---------------+-----+-----+-----+-----+-----+-----+ rabbit@rabbit-Lenovo-V570:~$

  Read the article

• apt-get upgrade stuck at the same package

  - by decibyte

  Current status I've started to suspect this is not an Ubuntu issue, but related to the internet connection here at my work. Until I'm sure, Im leaving my question below: Original question I'm stuck, can't upgrade my system. Running sudo apt-get upgrade gives me the following: mmm@alalunga:~$ sudo apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done The following packages have been kept back: ginn libgrip0 linux-generic-pae linux-headers-generic-pae linux-image-generic-pae The following packages will be upgraded: apport apport-gtk bind9-host build-essential dhcp3-client dhcp3-common dnsutils eog evince evince-common firefox firefox-branding firefox-dbg firefox-globalmenu firefox-gnome-support firefox-locale-en gimp gimp-data gir1.2-totem-1.0 glib-networking glib-networking-common glib-networking-services gnupg gpgv icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-6-plugin icedtea-netx icedtea-netx-common icedtea-plugin isc-dhcp-client isc-dhcp-common libapache2-mod-php5 libart-2.0-2 libbind9-80 libdns81 libevince3-3 libgimp2.0 libisc83 libisccc80 libisccfg82 liblwres80 libssl-dev libssl-doc libssl1.0.0 libtotem0 linux-firmware linux-libc-dev openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib openssl php-pear php5-cli php5-common php5-curl php5-dev php5-gd php5-mysql php5-xsl policykit-1-gnome python-apport python-django python-gst0.10 python-problem-report resolvconf thunderbird thunderbird-globalmenu thunderbird-gnome-support totem totem-common totem-mozilla totem-plugins xserver-xorg-input-synaptics 74 upgraded, 0 newly installed, 0 to remove and 5 not upgraded. Need to get 317 MB/327 MB of archives. After this operation, 1.481 kB of additional disk space will be used. Do you want to continue [Y/n]? Get:1 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:2 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:3 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:4 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:5 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:6 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:7 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] 9% [7 openjdk-6-jre-headless 27,3 MB/27,3 MB 100%] It keeps downloading the package openjdk-6-jre-headless, then does nothing for a while (hanging on what's the last line above), then download the package again. It's at its 13th download attempt at the moment of writing. The actual downloads seem to be done just fine, but whatever it does after downloading seems to be failing. I tried removing openjdk-6, but then it wanted to install openjdk-7 instead, with the same result, hanging at openjdk-7-jre-headless instead. I also tried changing servers from my local (Danish) to the main server. No luck. It's also keeping me from upgrading alle the other packages. What to do? Update After following instructions in the answer by @lpanebr, it is now stuck at the linux-firmware package. So, maybe it's a more general problem than being related to specific package(s)? Although it did download some packages without problems before getting stuck at linux-firmware.

  Read the article

• WiFi stops working after a while in Lenovo ThinkPad W520 (Ubuntu 12.04)

  - by el10780

  After several minutes(I do not know how many) there is no internet connection on my laptop via Wi-Fi.Ubuntu doesn't show any kind of message that my WiFi was disconnected neither there is a signal drop,but suddenly Firefox stops connecting to web pages.I checked my modem/router and it seems that it is working fine.I tried also to reboot the WiFi device and nothing happens.The only thing that it makes it work again is a reboot of the system and if I do not want to do a reboot then I am enforced to connect to the Internet using Ethernet cable.Does anybody know what is happening? ## Some Hardware info that might be helpful ## el10780@ThinkPad-W520:~$ sudo lshw -class network *-network description: Ethernet interface product: 82579LM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 04 serial: f0:de:f1:f1:be:10 size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k duplex=full firmware=0.13-3 ip=192.168.0.10 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:50 memory:f3a00000-f3a1ffff memory:f3a2b000-f3a2bfff ioport:6080(size=32) *-network description: Wireless interface product: Centrino Advanced-N + WiMAX 6250 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 5e serial: 64:80:99:63:14:74 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-26-generic firmware=41.28.5.1 build 33926 ip=192.168.0.6 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:52 memory:f3900000-f3901fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.3 logical name: wmx0 serial: 00:1d:e1:53:b2:e8 capabilities: ethernet physical configuration: driver=i2400m firmware=i6050-fw-usb-1.5.sbcf link=no el10780@ThinkPad-W520:~$ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:16.3 Serial controller: Intel Corporation 6 Series/C200 Series Chipset Family KT Controller (rev 04) 00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b4) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b4) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b4) 00:1c.4 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 (rev b4) 00:1c.6 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 7 (rev b4) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation QM67 Express Chipset Family LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation GF108 [Quadro 1000M] (rev a1) 03:00.0 Network controller: Intel Corporation Centrino Advanced-N + WiMAX 6250 (rev 5e) 0d:00.0 System peripheral: Ricoh Co Ltd Device e823 (rev 08) 0d:00.3 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 PCIe IEEE 1394 Controller (rev 04) 0e:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) el10780@ThinkPad-W520:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no 3: i2400m-usb:2-1.3:1.0: WiMAX Soft blocked: yes Hard blocked: no The weirdest thing is this screenshot which I took after running the **Additional Drivers** program.I mean I have a NVidia Quadro 1000M and my Intel Centrino WiFi Card and this shows that there are not proprietay drivers for my system. http://imageshack.us/photo/my-images/268/screenshotfrom201207062.png/

  Read the article

• My LAN USB NIC is not working in ubuntu 11.10?

  - by Gaurav_Java

  Today i start my system its seems that my LAN port is not working . so i buy one USB to LAN adapter and i plug in ubuntu system its doen't connect automatically .when i check result lsusb its shows me that there is one DM9601 Ethernet adapter is connected when i click on network information in panel its shows me that there is something " wired NEtwork (Broadcom NetLink BCM5784M gigabit Ethernet PCIe) I think want some driver for that .i don't have any idea how it can be used ? here output of sudo lspci -nn *00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07) 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07) 00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07) 00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03) 00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03) 00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03) 00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03) 00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03) 00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03) 00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03) 00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03) 00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03) 00:1d.3 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03) 00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93) 00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03) 00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03) 00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 03) 02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) 04:00.0 Network controller [0280]: Intel Corporation WiFi Link 5100 [8086:4232]* sudo lshw -class network *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 10 serial: 00:1f:16:9a:56:98 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=sb v2.19 latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:f4500000-f450ffff *-network DISABLED description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:22:fa:09:02:00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-17-generic firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:46 memory:f4600000-f4601fff *-network description: Ethernet interface physical id: 4 logical name: eth1 serial: 00:60:6e:00:f1:7d size: 100Mbit/s capacity: 100Mbit/s capabilities: ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=dm9601 driverversion=22-Aug-2005 duplex=full firmware=Davicom DM9601 USB Ethernet ip=192.168.1.34 link=yes multicast=yes port=MII speed=100Mbit/s I am using Wimax internet connection which i have to connect from browser . at that time my system is not showing that i am connected to any wired connection. but when i connect internet from other system after getting conneted to internet . when i plug again my USB LAN then its shows that you are conneted to wired connetion. here is screenshot for conneting wimax from browser after connecting to internet network connection shows

  Read the article

• Random Windows application crashes on Windows Server Hyper-V Core 2012

  - by Marlamin

  We're having some issues with our Hyper-V Core 2012 R2 installation on a HP DL360G8. We have an identical server with Hyper-V Core 2012 (not R2) that does not have these issues. When logging off from the physical server/via remote desktop, we sometimes get this error: Configure-SMRemoting.exe - Application Error : The application was unable to start correctly (0xc0000142). Click OK to close the application. We've also once or twice seen a "memory could not be read" error mentioning LoginUI.exe (another Windows app in System32) but have been unable to get an exact description. It's rather worrying to get such errors on a fresh install of Hyper-V 2012 R2. Is this even anything to worry about? Things we've done: Memtest86+, no memory errors Checksummed the file that is crashing with the one in the verified correct ISO, files match Server firmware upgrade to latest firmware of all present hardware, no visible changes Remade the RAID5 array , no change Reinstalled a few times, no change Reinstall without applying Windows updates after, no change

  Read the article

• Setting up dynamic DNS for linked router

  - by cherrun

  I have a 'main' router that receives the internet signal from the ISP and another one in my room, connected with a cable. The main router is running its original firmware and is very limited in its features, unfortunately I can not change this router, since my phone company has some hardcoded stuff in there and the internet will only work with this router. My second router is running DD-WRT firmware. Now I need to set up dynamic DNS, so I can access my NAS machine remotely, which is connected to the second router. As mentioned, this can't be done with the main router, due to its limited features. DHCP is turned off on the second router, since it gets its IP from the main one. Is there a possibility to set up dynamic DNS on the second router, without changing any (or much) on the main router? Maybe as a side note: I live in Germany, don't know if the set up of the routers are different in other countries.

  Read the article

• Setting up dynamic DNS for linked router

  - by cherrun

  I have a 'main' router that receives the internet signal from the ISP and another one in my room, connected with a cable. The main router is running its original firmware and is very limited in its features, unfortunately I can not change this router, since my phone company has some hardcoded stuff in there and the internet will only work with this router. My second router is running DD-WRT firmware. Now I need to set up dynamic DNS, so I can access my NAS machine remotely, which is connected to the second router. As mentioned, this can't be done with the main router, due to its limited features. DHCP is turned off on the second router, since it gets its IP from the main one. Is there a possibility to set up dynamic DNS on the second router, without changing any (or much) on the main router? Maybe as a side note: I live in Germany, don't know if the set up of the routers are different in other countries.

  Read the article

• Connection issues with Linksys WRT54GL / Tomato

  - by Phoshi

  So I recently purchased a new router, and decided to put Tomato on it for some of the fancy features, like graphs. Only problem is, now I've installed it I can't connect to the internet any more! What I've done so far is plug the router in, connect to it wirelessly, and upgrade the firmware to the right version for my router. This went swimmingly, the router restarted, and everything's Tomatoey. Except it won't, now, connect to the internet, and I'm entirely unsure what I've missed. My old router was a BT Homehub, my ISP is BT (British Telecommunications). I'm a bit lost, this is the first time I've done any of this 3rd party firmware stuff.

  Read the article

• Cannot set MemOpMode or ProcVirtualization with syscfg.exe

  - by EGr

  When attempting to set MemOpMode or ProcVirtualization with syscfg.exe, I get the following error: C:\Users\EGr>syscfg --MemOpMode=AdvEccMode System Services or CSIOR disabled In the past, I have been told that this can be resolved by forcefully reinstalling the Dell Lifecycle controller firmware, and then trying again; however, I cannot find my notes on how to do that. Has anyone ever run into this issue, and does anyone know how I can fix it? If it is possible to forcefully reinstall the firmware, how would I do that? I've tried running the installer, but it fails after running for ~2 min. I believe there is a way to fix this as well, by adding/modifying a registry value at HKLM\System\Control\CurrentControlSet\Services\IPMIDRV (that might not be the correct path, but I know it is IPMIDRV). Is this a common issue? What is the actual cause of it?

  Read the article

• Netgear Wireless-n 150 wrn1000v2

  - by Jordan

  I'm not sure if this is the place to ask this question, move it if it's not. I'm trying to fix a wireless network. It only connects to a few devices and when it does work the connection is spotty. The router is a netgear wireless-n 150 wrn1000v2. Connecting to the router isn't a big problem, but connecting to the internet via WiFi is. I can't upgrade the firmware becuase it is from Comcast and it seems as though they only allow their versions of the firmware. I've monitored the network with wireshark and I see that the devices that are having trouble connecting are constantly asking "who is 192.168.1.1 tell 192.168.1.x" where x is the ip for the device. 192.168.1.1 is the router. This is from running wireshark on the wireless device. What does this mean. At this point I feel like buying a new router is the only option.

  Read the article

• How to make a pxe bootable 10MegaByte or larger dos image?

  - by rjt

  Would like to make a "massive" DOS floppy disk image, say 10MegaBytes or more containing all the firmware updates i need for any system, harddrive, BIOS. i do not need the DOS image to be networkable as everything will be on the PXE booted image, but networking would be nice. Since ZipDisks were attached to the floppy disk controller and were over 100MegaBytes, this should be possible. i tried a long time ago to do this and spent too much time on it only to have it fail to boot. So if someone has reliable instructions on how to create such a nightmarish beast and edit it, please let me know. One image that can used for PXE and copied to a USB stick would be a plus. Too bad manufacturers don't supply a single bootable Linux ISO containing all their firmware updates, that would be easy to boot over-the-lan and have networking. HP servers do this and it is awesome.

  Read the article

• Problem with Jumbo Frames

  - by Spookyone

  Hello, I am trying to set up jumbo frames on my gigabit home LAN but no luck so far. My setup is: * D-Link DIR-655 router, HW Revision A3, Firmware 1.21 EU * Synology DS107+, Firmware 3.0-1337 * Laptop w/ Win7 x64, external PCIx NIC managed by "Generic Marvel Yukon 88E8053 based Ethernet Controller" The router is supposed to support jumbo frames but doesn't feature any relevant setting. I set the Jumbo Packet value to 9000 on both the NIC and the Synobox but it doesn't work, ping -f -l 8972 says "Packet needs to be fragmented but DF set". Is there any other setting I overlooked, the DIR-655 doesn't actually support jumbo frames, or what else could be the problem?

  Read the article

• Experience with AMCC 3ware 9650se raid cards? Ours seems dead

  - by antiduh

  We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated.

  Read the article

• Backup to disk, encrypted, without any installed local software

  - by user30064

  Hi, Ok, this is a tough one, and it might not even be possible, but no harm in asking I guess. I have a Buffalo Terastation file server that I use for network attached storage. After a couple of phone calls to customer services I realised that there is no way to backup to disk encrypted. In effect, I would be carrying unencrypted company data off-site daily, which is obviously unacceptable. I had a go at TrueCrypt, EncFS, and a few others, and as far as I could see all of them required that you install some software on the machine that is to use the file system, which makes sense. Unfortunately the firmware on the Terastation is closed and I cannot install any software (and I can't build from source either, since Buffalo didn't include a compiler). Are there any ways to copy files to disk, where as soon as they are written to the disk they are transparently encrypted, without having to install additional software? I'm not sure it matters too much, but the Terastation firmware is Linux based, although as I mentioned, closed. Many thanks, Andreas

  Read the article

• Boot disc isnt loading on MY system

  - by acidzombie24

  I am trying to update the firmware on my harddisk. I grabbed seagates windows setup tool which didnt boot into the app to update the firmware so I burned their iso image. Their ISO also doesnt boot and i vaguely remember something about windows not recognize my disc because of an EFI thing. It probably has nothing to do with it. Anyways, how do I boot into the disc? I tried going into advance options to boot directly to the disc and i get a blank screen. I can use ctrl+alt+del which reboot the system but other then that its blank and doesnt seem to load anything on the disc. The disc was a 7mb iso burnt using windows 7 built in iso burner (it suggest using it on seagates site). I have no idea what to do. Do any of you guys know what my problem may be? The media is DVD-R

  Read the article

• "custom" routers for VPN - useful or waste of money?

  - by Andrew Heath

  I use VPN in China and my current service contract expires soon so I was checking what sort of plans are out there now. I found that Witopia offers a "Cloak Box", what appears to be a Linksys wireless router with allegedly hacked/custom firmware to support VPN. Aside from allowing multiple computers to share one VPN connection, is there anything else at work here to justify that price when most new routers are $100 or less these days? Or is this something targeted towards the cd-rom cupholder crowd? And yes, I've contacted them, but haven't heard back yet... EDIT I've heard back from the company - here are the details if anyone else is interested: the router is a Linksys WRT54GL running TomatoVPN custom firmware the hardware waranty is one (1) year, from Linksys/Cisco the VPN is hard-set, so any device connected to the router MUST use the VPN (Witopia blocks torrents) I've decided it's not for me, but hopefully this information will prove useful to others.

  Read the article

• How to create an EFI System Partition?

  - by Alex Popov

  TL; DR How do I create an EFI system partition from scratch? How do I put the EFI firmware on it onces it is created? Long version I hava Toshiba T430 laptop. I received it with Windows 7 installed (but I think originally it has shipped with Windows 8). I installed Ubuntu on it, but deleted some partitions on the disk so that I ended up wiping out the Windows and only having Ubuntu. Among the deleted partitions was the EFI System partition. I discovered that Ubuntu now boots in Legacy mode (and not UEFI). I am trying to follow this guide on converting my Ubuntu installation from Legacy to UEFI. The problem - since there is no EFI partition whenever I choose from BIOS to boot using UEFI I cannot boot. That counts not only for the harddrive, but usb and DVD as well. I think this is logical - it expects an EFI partition and since it can't find it, it cannot continue booting futher, be it from HDD or DVD. So how do I recreate the EFI partition? The guide above says: Creating an EFI partition If you are manually partitioning your disk in the Ubuntu installer, you need to make sure you have an EFI partition set up. If your disk already contains an EFI partition (eg if your computer had Windows8 preinstalled), it can be used for Ubuntu too. Do not format it. It is strongly recommended to have only 1 EFI partition per disk. An EFI partition can be created via a recent version of GParted (the Gparted version included in the 12.04 disk is OK), and must have the following attributes: Mount point: /boot/efi (remark: no need to set this mount point when using the manual partitioning, the Ubuntu installer will detect it automatically) Size: minimum 100Mib. 200MiB recommended. Type: FAT32 Other: needs a "boot" flag. I had some trouble creating this partition: I boot from a live Ubuntu DVD, open GParted, create a 200MB partition and format it to FAT32. In GParted I cannot set the mount point and thus cannot set the bootflag. I didn't set the mount point in /etc/fstab since it's a live CD and fstab looked quite differently from what I expected compared to a normal boot. Anyway, I just didn't know what values to set. I booted again via the live DVD and then chose to install Ubuntu. I then created a partition with the mentioned criteria - mount point, 200MB, FAT32, boot flag. However, I continue to have this problem and I suppose it's because on that partition there is no EFI firmware, it's just an empty partition, which is suitable to have EFI firmware. So again, how do I create an EFI partition, which has the EFI software, so that the laptop can once again boot in UEFI mode?

  Read the article

• windows 7 wireless knocks off other computers on the network

  - by Sean

  I am trying to fix a wireless network issue. When a new windows 7 machine (we have 2 in the house) we have problems with any other windows xp machines connecting to the wireless network. I am using a linksys WRT110 running Firmware Version: 1.0.04 (which is not the latest firmware its Ver.1.0.07 but the router would not use the bin update file). I have tried a ton of variations in setting for the wireless network, changed the channel, the security level (none, wep wpa, wpa2), network type (g,bg mixed). I have also read some stuff about homegroup settings for windows 7 but have not seen any differences that make a difference. Basically windows 7 does not like to connect to our network but when I manage to get it to work the windows xp pro machines get kicked off. The windows xp pro machines are a few years old but both windows 7 machines are less than 6 months old.

  Read the article

• Two Routers - 1 Port Straight to First Router

  - by apples

  At my house we have two Wifi routers one's connected directly to the modem and the other is plugged in down stairs as a second network(Directly connected to the first router) Is there a way that I could make it so that I have the second router have its own network, but have one or two ports that would act as if they were directly connected to the first router? That way I can port forward to devices on the second router. Here are the information about the routers: Router 1 - Linksys WRT54G Running stock firmware Router 2 - Linksys E900 Running Tomato Firmware So to summarize what I'm asking is how would I have two networks from two routers but be able to connect directly to the first router through one of the ports on the second router. Here's a Visio Drawing of what I would like to look like

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >