Search Results

Search found 1051 results on 43 pages for 'nic foster'.

Page 10/43 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

  • Bind DHCP Server to Network Bridge

    - by Luke
    My wireless router died, so I decided to route everything through my server. So I installed a second NIC and a wireless card to be my new network: 1 NIC to the Modem, 1 NIC to the switch, and the Wireless to... Well, wireless. Anyways, I got far enough to get DHCP to work on just ONE adapter when I used Internet Connection Sharing (I couldn't get RRAS set up for the life of me), then I decided to try bridging the wireless and second NIC. Now, the DHCP server won't bind to the bridge, but I can enter manual IP's in my clients and it'll connect to the Internet. I also tried changing my wireless adapter's IP to 192.168.0.2, and to 192.168.1.1 to try to set up a separate scope, but to no avail. Running Windows Server 2003

    Read the article

  • No compatible network card

    - by sbintcliffe
    Motherboard: Asus K8N-E Deluxe with onboard NIC (nVidia nForce) Secondary NIC: I've tried using a standard NIC (Device Manager displays this as D-Link DFE-538TX 10/100, but under manufacturer in the General tab of the properties in Windows it states Realtek Semiconductor Corp.) I have downloaded ESXi 4.0.0 build 208167 and cooked to disc. I've booted from it, the .TGZ modules load from the yellow and grey screen, the progress bar reaches to about 60% and like a second later the screen changes and I have the following information on screen; "No compatible network adapter found. Please consult the HCG." I've checked the HCG and found that my motherboard is listed. I also get the same message with the secondary NIC. Any ideas please?

    Read the article

  • Packet drop measured by ethtool, tcpdump and ifconfig

    - by Rayne
    Hi all, I have a question regarding packet drops. I am running a test to determine when packet drops occur. I'm using a Spirent TestCenter through a switch (necessary to aggregate Ethernet traffic from 5 ports to one optical link) to a server using a Myricom card. While running my test, if the input rate is below a certain value, ethtool does not report any drop (except dropped_multicast_filtered which is incrementing at a very slow rate). However, tcpdump reports X number of packets "dropped by kernel". Then if I increase the input rate, ethtool reports drops but "ifconfig eth2" does not. In fact, ifconfig doesn't seem to report any packet drops at all. Do they all measure packet drops at different "levels", i.e. ethtool at the NIC level, tcpdump at the kernel level etc? And am I right to say that in the journey of an incoming packet, the NIC level is the "so-called" first level, then the kernel, then the user application? So any packet drop is likely to happen first at the NIC, then the kernel, then the user application? So if there is no packet drop at the NIC, but packet drop at the kernel, then the bottleneck is not at the NIC? Thank you. Regards, Rayne

    Read the article

  • NAT ports - how do they work?

    - by Davidoper
    I have the following network schema: Computer A: three nics: NIC 1 (eth0): dhcp, public internet NIC 2 (eth1): static 192.168.1.1, gateway for Computer B NIC 3 (eth2): static 192.168.2.1, gateway for Computer C Computer B: static 192.168.1.2, using gateway 192.168.1.1 (NIC 2). Computer C: static 192.168.2.2, using gateway 192.168.2.1 (NIC 3). So I applied this to get NAT working: iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE Every computer can connect to the internet now. I have been applying rules to the main computer (Computer A), like dropping connections to some ports, e.g ssh: iptables -A INPUT -p tcp --dport 22 -j DROP But for instance, now I would like only allow connections for ports 20,21,22,53 and 80 in Computer C, and ignore the outside traffic if it's not related to those ports. The allowed connections should be FROM Computer C to outside, but not from outside to Computer C (I mean - Computer C is not hosting any HTTP or SSH, but it is going to use them as a client). I guess this sould be done like this: iptables -A OUTPUT -i eth2 -o eth0 -p tcp --dport 21 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth2 -o eth0 -p tcp --sport 21 -m state --state ESTABLISHED -j ACCEPT The last rule (dropping any other traffic different from those) is at the end of the configuration, so -A should be working correctly. The thing is... it is not working. If I put the last rule like this: iptables -A FORWARD -i eth2 -o eth0 -j DROP It just drops everything and, for instance, port 21 (previously opened as you can see above) is not either working. Can you tell me what could I have done wrong? I have been struggling with this problem for some time and I am unable to solve it. Thanks!

    Read the article

  • Server 2008 NAT Internet Not Working

    - by Jack
    I'm trying to set up Routing and Remote Access on Windows Server 2008 R2, I have a network connection that I want to share the internet from to another private network. The server has two NICs which are configured as follows: External NIC (Dynamically assigned by ISP) IP:10.175.4.150 Subnet:255.255.192.0 Gateway:10.175.0.1 DNS:10.175.0.1 Internal NIC IP:172.16.254.1 Subnet:255.255.255.0 Gateway:None DNS:None I have set the external NIC to be the public interface and enabled NAT on it in the RRAS MMC and set the internal NIC to be a private interface. I have also set up the DNS forwarding or whatever it is in the NAT section. From a client (IP:172.16.254.2) I can ping the server and access files on it, when I try to browse the web with the default gateway set to the internal NIC ip I end up getting a 404 page which is returned from the ISPs default gateway. I'm guessing it's something to do with the double NAT possibly. Trying to ping the ISPs default gateway from a private network client just times out as does accessing it directly. I've disabled and reconfigured RRAS multiple times and that doesn't seem to have made a difference, so can anyone tell me what I'm doing wrong? Thanks.

    Read the article

  • Moving Farm to co-location hosting - network settings requirements

    - by Saariko
    I am moving my farm (2 Dell's R620) to a co-location hosting service. I am trying to figure out the secure way to have my network settings The requirements are: VM1 is the working HOST, includes: esxi 5.1, vSphere, 4 clients (w2008r2 all) VM2 has esxi 5.1 installed, and a single machine with Veeam Backup and copy 6.5 - keeping a copy of VM1 clients on the VM2 internal storage (this solution is due to a very small budget - in case of failure on Host 1 - can redirect IP's) Only 2 VM clients require network address and access from the WWAN - ISP provides IP's range for them (with Gateway and DNS) I need connection to the iDrac's from my office (option to create a VPN-SSL tunnel) Connection to the vSphere appliances I want to be able to RDP to the VM clients The current configuration is that each host has the iDrac dedicated nic connected , and another (NIC #1) connected - with a static IP on 192.168.3.x The iDrac's have a static IP from the same network range (19.168.3.x) It will look something like this: My thoughts: On NIC#2 of both hosts I will connected a crossed cable I will give each VM clients that needs internet access a 2ndry VM network with the assigned IP from the ISP open only to web - can not access from the My Question: Should I give IP's (external) to the machines who DO NOT require WWAN Access? - I can't see a way to RDP to them directly if not. Should I use the crossed cable? or just plug NIC #2 to the switch? Will this setup even work? What do I need to verify? What Virtual nic's and/or switches should I create on the Hosts?

    Read the article

  • How do you confirm network adapter is gigabit capable?

    - by StrandedPirate
    Upgrading my network to gigabit speeds and don't know how to determine if the NIC in one of the systems is capable of gigabit speed. The documentation from the manufacturer states this: Network adapter 10/100/1000 Ethernet LAN on system board However when I go to the properties of the NIC under Speed & Duplex my only options are: 10 Mb Full 10 Mb Half 100 Mb Full 100 Mb Half Auto Is there a command line I can run that will give me more detail about the NIC? Windows 7 x64 OS New Info: The new switch I just bought has a light to indicate 1000Mbps. I can tell from the light that this NIC is indeed negotiating at 1000Mbps but I'd still like to know how to determine this from the console in windows.

    Read the article

  • Do all routers really must know all routes to every router?

    - by Philipili
    This is my complicated and long question. First let's talk about the context. Network topology: PC A --- RT A --- RT C --- RT B --- PC B (RT C has a WAN NIC connected to "the cloud") With this situation : PC A must send a packet to PC B Default routes direct packets to the cloud We haven't access to RT C's configuration RT C only knows how to join network A, not network B RT A knows about network B RT B knows about network A RT C's routing table: Destination NIC Gateway 0.0.0.0 WAN Cloud Network A LAN A RT A's WAN RT A's routing table: Destination NIC Gateway 0.0.0.0 WAN LAN A Network B WAN LAN A RT B's routing table: Destination NIC Gateway 0.0.0.0 WAN LAN B Network A WAN LAN B I would like to permit PC A and PC B to communicate, but I don't have access to RT C. Networks B and BC are new. Can PC A send a packet to RT B's WAN NIC (which is possible) and "ask RT B to direct the packet to PC B" ? I believe replacing RT B with a VPN server should do the trick, but I would like to know if it is possible to make it without establishing a new connection.

    Read the article

  • How to remove an "extra" (unwanted) network from a windows 2008 failover cluster?

    - by Trondh
    Hi, We had a severe crash on one node of our 2-node Windows 2008 / Exchange 2007 CCR Cluster the other day, and i tried to rebuild the node from scratch. I'm using this as a rough outline: http://edmckinzie.spaces.live.com/Blog/cns!687C72A5909E4230!508.entry?sa=641979772 The problem: Our cluster was originally setup with only one NIC per host, as this is supposedly supported in Win2008 (no dedicated heartbeat NIC). When I add my freshly installed node to the cluster, it shows up with two cluster networks, "Cluster Network 1" & 2. The existing node's NIC has been placed in one cluster network and my fresh installed has ended up in the other. I can't find anywhere in the GUI to choose which cluster network each physical NIC should be part of, but i KNOW I have done this before. Time is of the essence on this one, so I was hoping someone in here had the answer on the top of their head... Thanks for any pointers. regards, Trond Hindenes

    Read the article

  • CentOS 5.8 dig is not resolving ip-address

    - by travisbotello
    I'm running centos 5.8 on a local machine at home. Today I was trying to analyze the DNS-Lookup via dig. $ dig +trace -t A www.heise.de. This is giving me something like this as a response de. 172800 IN NS f.nic.de. de. 172800 IN NS z.nic.de. de. 172800 IN NS s.de.net. de. 172800 IN NS n.de.net. de. 172800 IN NS a.nic.de. de. 172800 IN NS l.de.net. ;; Received 344 bytes from 192.58.128.30#53(192.58.128.30) in 49 ms In contrast my dedicated CentOS machine is returning the following de. 172800 IN NS a.nic.de. de. 172800 IN NS n.de.net. de. 172800 IN NS f.nic.de. de. 172800 IN NS z.nic.de. de. 172800 IN NS l.de.net. de. 172800 IN NS s.de.net. ;; Received 344 bytes from 192.58.128.30#53(j.root-servers.net) in 32 ms As you can see, the last line is different. Any idea why my dedicated machine is giving me the host name of the responding DNS-Server and my local machine is only returning the ip-address? Thanks in advance UPDATE The reverse DNS-Lookup is working without any problems. Also, I just checked this on my local mac and...exactly the same problem occurs. Is it possible that this has to do with the local router/modem/ISP?

    Read the article

  • Simple Linux program that takes any HTTP/HTTPS request and returns a single page?

    - by ultrasawblade
    I have a Linux box operating as router. There's a NIC that's connected to the internet (WAN), a NIC connected to an 8-port GbE switch (LAN), and a NIC connected to a Linksys wireless N-router (WLAN). Routing between everything is working perfectly. I have security completely disabled on the wireless router, but the WLAN NIC is firewalled such that it will only accept DNS queries and PPTP VPN connections. Currently HTTP/HTTPS traffic and everything else is blocked. I would like to run something that listens on port 80/443 of the WLAN NIC, and, for non VPN'ed connections, given any HTTP/HTTPS request it will return a single webpage saying "Unauthenticated" and explain how to sign into the VPN. A transparent proxy seems to be what I need, but my searches all seem to direct me to Squid, which is already running on my server and seems overkill for this simple task. Is there a simpler, lightweight program out there that does just this or should I just suck it up and run two instances of Squid (or figure out how to configure it)? Or, is this entire VPN thing I'm doing complete nonsense and I should just enable encryption on the wireless router?

    Read the article

  • Hyper-V networking....still not sure which way to go??

    - by CZhale
    We have our Hyper-V server up and running (Windows 2008 ENT SP2) and started to create some of our VMs. The server has 4 total nics. 2 onboard Broadcom 1gb nic cards and a pci dual port Intel Pro cards 1gb. Right now, I have setup 1 broadcom nic to be the hyper-v host nic, and setup the other broadcom nic for the VMs. We are not using the Intel Nics....should we be thinking about teaming?Link Aggregation?? I just want to achieve the best possible setup for the network, but have read many things for and against teaming the nics?? Thoughts?

    Read the article

  • Any program to help me check whether an ethernet channel can support full-length VLAN packet?

    - by Jimm Chen
    Sometimes, I have to face such a situation that I need to quickly and explicitly know whether a full length VLAN packet can traverse between two RJ45 ports. Yes, I mean 802.1Q ethernet frame with Etype=81 00 (diagram below). What I can do now is: Get two Windows PCs, for each PC, intall Intel Gigabit NIC and Intel specific driver to create a virtual NIC, with VLAN ID=3 assigned. Then connect the two PCs to each of the two RJ45 port. Finally execute ping to generate a full-length ethernet packet. ping -f -l 1472 <dest-IP> This way, I can be sure that the sent packet has the maximum "IP data payload" of 1500 bytes(8 bytes of ICMP header and 1472 bytes of ICMP data). If the ping gets reply, I know that the ethernet channel support full-length VLAN packet. From my experiment, some home switch or broad band routers(e.g. Linksys WRT54G) does not support full-length VLAN packet switching, so only ping -f -l 1468 succeeds. You see, I have to use an expensive Intel NIC to carry on that test, quite inconvenient. You know, for most laptop today, they do not equip an Intel NIC, and, even it is an Intel NIC, Intel VLAN driver, Intel has limitations on the models on which VLAN driver can be installed. So, my question is: Is there a small program that can let me send a full-length VLAN packet without installing a dedicated VLAN driver? Or better, the program has a stock feature that does the very job for my situation. Windows programs preferred, Linux solution welcome. Simpler the program, the better. Thank you.

    Read the article

  • Ubuntu 10.04 Windows2003 adding a route for GPO assignment

    - by David Carvalho
    I want the PC's that receive IP from my Ubuntu DHCP3-server to be able to retrieve the GPOs that are on my windows 2003 server. I'm using virtualbox and 3 virtual machines: 1 windows 2003 server 192.168.0.2 with 1 NIC (internal network). 1 ubuntu server 10.04 lts 192.168.0.1 with 1 NIC (internal network) and 3 aliases 192.168.21.0, 192.168.22.0, 192.168.100.0 1 Windows XP machine with 3 NIC's (internal network).

    Read the article

  • Very Slow DSL (ethernet) speed [New Interesting Update]

    - by Abhijit
    Very IMPORTANT and INTERESTING UPDATE: Due to some reason I just thought to do a complete new setup and this time I decided to again have openSUSE plus ubuntu. So I first reinstall lubuntu and then I installed OpenSUSE 12.2 (64 bit). Now, my DSL speed is working very normal and fine on opensuse. So this is very scary. Is it possible for any operating system to manipulate my NIC so that it will work fine only on that operating system and not on another os? Regarding positive thinking and not being paranoid, what is it that makes ONLY suse to get my NIC to work at normal speed but ubuntu can not do it? Not even fedora? Not even linux mint? What all these OS are lacking that enables suse to work great? == ORIGINAL QUESTION == I 'was' on opensuse 12.2 when my dsl speed was normal. Yesterday I switched from opensuse to ubuntu 12.04 and speed decreased. It came to range of 7-10-13-20-25-kbps. Then I switch to linux mint, and then to fedora. Still slow speed. When I was in ubuntu I disabled ipv6 but still no luck. Now I am in fedora but this time with DIFFERENT ISP. And still I am getting very slow sped. So my guess is this is nothing to do with os. What can be wrong? Is this problem of NIC? Does NIC speed decreases over time? Does NIC life ends over time as with keyboard or mouse? Help please All the os I used are 64 bit and my laptop is Compaq Presario A965Tu Intel Centrino DUal Core. Interesting thing to notice is I get normal speed while downloading torrent inside torrent client softwares. This slow speed issue applied to download from any web browser or installing software using terminal.

    Read the article

  • windows: force user to use specific network adapter

    - by Chad
    I'm looking for a configuration/hack to force a particular application or all traffic from a particular user to use a specific NIC. I have an legacy client/server app that has a "security feature" that limits connections based on IP address. I'm trying to find a way to migrate this app to a terminal server environment. The simple solution is for the development team to update the code in the application, however in this case that's not an option. I was thinking I might be able to install VMware NIC's installed for each user on the terminal server and do some type of scripting to force that user account to use a specific NIC. Anybody have any ideas on this? EDIT 1: I think I have a hack to work around my specific problem, however I'd love to hear of a more elegant solution. I got lucky in that the software reads the server IP address out of a config file. So I'm going to have to make a config file for each user and make a customer programs files for each user. Then add a VMware NIC for each user and make each server IP address reside on a different subnet. That will force the traffic for a particular user to a particular IP address, however its really messy and all the VM NIC's will slow down the terminal server. I'll setup a proof of concept Monday and let the group know how it affects performance.

    Read the article

  • Wireshark vs Netmon for precise time tagging

    - by Nic
    I'm using Wireshark to time tag and get some statistics on multicast traffic. When there is not much traffic, the stats looks good, but as soon as there is a bunch of packets arriving at the same time, I have stats that are not even possible (e.g. round trip time of 0ms) I'm wondering if Netmon could be more precise in time tagging packet because it is not relying on the Winpcap driver? Does anybody already faced the same situation? Thanks a lot, Nic

    Read the article

  • How to eliminate NULL fields in TSQL

    - by salvationishere
    I am developing a TSQL query in SSMS 2008 R2. I am trying to develop this query to identify one record / client. Because some of these values are NULL, I am currently doing LEFT JOINS on most of the tables. But the problem with the LEFT JOINs is that now I get 1 record for some clients. But if I change this to INNER JOINs then some clients are excluded entirely because they have NULL values for these columns. How do I limit the query result to just one record / client regardless of NULL values? And if there are non-NULL values then I want it to choose the record with non-NULL values. Here is some of my current output: group_profile_id profile_name license_number is_accepting is_accepting_placement managing_office region vendor_name vendor_id applicant_type Office Address status_description Cert Date2 race ethnicity_desc religion 9CD932F1-6BE1-4F80-AB81-0CE32C565BCF Atreides Foster Home 1 Atreides1 1 Yes Manchester, NH Gulf Atlantic Atreides1 00000007 Treatment Foster Home 4042 Arrakis Avenue, Springfield, VT 05156 Open/Re-opened 2011-06-01 00:00:00.000 NULL NULL NULL DCE354D5-A7CC-409F-B5A3-89BF664B7718 Averitte, Leon and Sandra 00000044 1 Yes Birmingham, AL Gulf Atlantic AL Averitte, Leon and Sandra 00000044 Treatment Foster Home 3816 5th Avenue, Bessemer, AL 35020, (205)482-4307 Open/Re-opened 2011-08-05 00:00:00.000 NULL NULL NULL DCE354D5-A7CC-409F-B5A3-89BF664B7718 Averitte, Leon and Sandra 00000044 1 Yes Birmingham, AL Gulf Atlantic AL Averitte, Leon and Sandra 00000044 Treatment Foster Home 3816 5th Avenue, Bessemer, AL 35020, (205)482-4307 Open/Re-opened 2011-08-05 00:00:00.000 Caucasian/White Non Hispanic NULL AD02A43C-6F38-4F35-8C9E-E12422690BFB Bass, Matthew and Sarah 00000076 1 Yes Jacks on, MS Central Gulf Coast MS Bass, Matthew and Sarah 00000076 Treatment Foster Home 506 Eagelwood Drive, Florence, MS 39073, (601)665-7169 Open/Re-opened 2011-04-01 00:00:00.000 NULL NULL NULL AD02A43C-6F38-4F35-8C9E-E12422690BFB Bass, Matthew and Sarah 00000076 1 Yes Jackson, MS Central Gulf Coast MS Bass, Matthew and Sarah 00000076 Treatment Foster Home 506 Eagelwood Drive, Florence, MS 39073, (601)665-7169 Open/Re-opened 2011-04-01 00:00:00.000 Caucasian/White NULL Baptist You can see that both Averitte and Bass profile names have one record with NULL race, ethnicity, religion. How do I eliminate these rows (rows 2 and 4)? Here is my query currently: select distinct gp.group_profile_id, gp.profile_name, gp.license_number, gp.is_accepting, case when gp.is_accepting = 1 then 'Yes' when gp.is_accepting = 0 then 'No ' end as is_accepting_placement, mo.profile_name as managing_office, regions.[region_description] as region, pv.vendor_name, pv.id as vendor_id, at.description as applicant_type, dbo.GetGroupAddress(gp.group_profile_id, null, 0) as [Office Address], gsv.status_description, ri.[description] as race, ethnicity.description as ethnicity_desc, religion.description as religion from group_profile gp With (NoLock) --Office Information inner join group_profile_type gpt With (NoLock) on gp.group_profile_type_id = gpt.group_profile_type_id and gpt.type_code = 'FOSTERHOME' and gp.agency_id = @agency_id and gp.is_deleted = 0 inner join group_profile mo With (NoLock) on gp.managing_office_id = mo.group_profile_id left outer join payor_vendor pv With (NoLock) on gp.payor_vendor_id = pv.payor_vendor_id left outer join applicant_type at With (NoLock) on gp.applicant_type_id = at.applicant_type_id and at.is_foster_home = 1 inner join group_status_view gsv With (NoLock) on gp.group_profile_id = gsv.group_profile_id and gsv.status_value = 'OPEN' and gsv.effective_date = (Select max(b.effective_date) from group_status_view b With (NoLock) where gp.group_profile_id = b.group_profile_id) left outer join regions With (NoLock) on isnull(mo.regions_id, gp.regions_id) = regions.regions_id left join enrollment en on en.group_profile_id = gp.group_profile_id join event_log el on el.event_log_id = en.event_log_id left join people client on client.people_id = el.people_id left join race With (NoLock) on el.people_id = race.people_id left join group_profile_race gpr with (nolock) on gpr.race_info_id = race.race_info_id left join race_info ri with (nolock) on ri.race_info_id = gpr.race_info_id left join ethnicity With(NoLock) On client.ethnicity = ethnicity.ethnicity_id left join religion on client.religion = religion.religion_id

    Read the article

  • Great Blogs About Oracle Solaris 11

    - by Markus Weber
    Now that Oracle Solaris 11 has been released, why not blog about blogs. There is of course a tremendous amount of resource and information available, but valuable insights directly from people actually building the product is priceless. Here's a list of such great blogs. NOTE: If you think we missed some good ones, please let us know in the comments section !  Topic Title Author Top 11 Things My 11 favourite Solaris 11 features Darren Moffat Top 11 Things These are 11 of my favorite things! Mike Gerdts Top 11 Things 11 reason to love Solaris 11     Jim Laurent SysAdmin Resources Solaris 11 Resources for System Administrators Rick Ramsey Overview Oracle Solaris 11: The First Cloud OS Larry Wake Overview What's a "Cloud Operating System"? Harry Foxwell Overview What's New in Oracle Solaris 11 Jeff Victor Try it ! Virtually the fastest way to try Solaris 11 (and Solaris 10 zones) Dave Miner Upgrade Upgrading Solaris 11 Express b151a with support to Solaris 11 Alan Hargreaves IPS The IPS System Repository Tim Foster IPS Building a Solaris 11 repository without network connection Jim Laurent IPS IPS Self-assembly – Part 1: overlays Tim Foster IPS Self assembly – Part 2: multiple packages delivering configuration Tim Foster Security Immutable Zones on Encrypted ZFS Darren Moffat Security User home directory encryption with ZFS Darren Moffat Security Password (PAM) caching for Solaris su - "a la sudo" Darren Moffat Security Completely disabling root logins on Solaris 11 Darren Moffat Security OpenSSL Version in Solaris Darren Moffat Security Exciting Crypto Advances with the T4 processor and Oracle Solaris 11 Valerie Fenwick Performance Critical Threads Optimization Rafael Vanoni Performance SPARC T4-2 Delivers World Record SPECjvm2008 Result with Oracle Solaris 11 BestPerf Blog Performance Recent Benchmarks Using Oracle Solaris 11 BestPerf Blog Predictive Self Healing Introducing SMF Layers Sean Wilcox Predictive Self Healing Oracle Solaris 11 - New Fault Management Features Gavin Maltby Desktop What's new on the Solaris 11 Desktop? Calum Benson Desktop S11 X11: ye olde window system in today's new operating system Alan Coopersmith Desktop Accessible Oracle Solaris 11 - released! Peter Korn

    Read the article

  • Networking in VirtualBox

    - by Fat Bloke
    Networking in VirtualBox is extremely powerful, but can also be a bit daunting, so here's a quick overview of the different ways you can setup networking in VirtualBox, with a few pointers as to which configurations should be used and when. VirtualBox allows you to configure up to 8 virtual NICs (Network Interface Controllers) for each guest vm (although only 4 are exposed in the GUI) and for each of these NICs you can configure: Which virtualized NIC-type is exposed to the Guest. Examples include: Intel PRO/1000 MT Server (82545EM),  AMD PCNet FAST III (Am79C973, the default) or  a Paravirtualized network adapter (virtio-net). How the NIC operates with respect to your Host's physical networking. The main modes are: Network Address Translation (NAT) Bridged networking Internal networking Host-only networking NAT with Port-forwarding The choice of NIC-type comes down to whether the guest has drivers for that NIC.  VirtualBox, suggests a NIC based on the guest OS-type that you specify during creation of the vm, and you rarely need to modify this. But the choice of networking mode depends on how you want to use your vm (client or server) and whether you want other machines on your network to see it. So let's look at each mode in a bit more detail... Network Address Translation (NAT) This is the default mode for new vm's and works great in most situations when the Guest is a "client" type of vm. (i.e. most network connections are outbound). Here's how it works: When the guest OS boots,  it typically uses DHCP to get an IP address. VirtualBox will field this DHCP request and tell the guest OS its assigned IP address and the gateway address for routing outbound connections. In this mode, every vm is assigned the same IP address (10.0.2.15) because each vm thinks they are on their own isolated network. And when they send their traffic via the gateway (10.0.2.2) VirtualBox rewrites the packets to make them appear as though they originated from the Host, rather than the Guest (running inside the Host). This means that the Guest will work even as the Host moves from network to network (e.g. laptop moving between locations), and from wireless to wired connections too. However, how does another computer initiate a connection into a Guest?  e.g. connecting to a web server running in the Guest. This is not (normally) possible using NAT mode as there is no route into the Guest OS. So for vm's running servers we need a different networking mode.... Bridged Networking Bridged Networking is used when you want your vm to be a full network citizen, i.e. to be an equal to your host machine on the network. In this mode, a virtual NIC is "bridged" to a physical NIC on your host, like this: The effect of this is that each VM has access to the physical network in the same way as your host. It can access any service on the network such as external DHCP services, name lookup services, and routing information just as the host does. Logically, the network looks like this: The downside of this mode is that if you run many vm's you can quickly run out of IP addresses or your network administrator gets fed up with you asking for statically assigned IP addresses. Secondly, if your host has multiple physical NICs (e.g. Wireless and Wired) you must reconfigure the bridge when your host jumps networks.  Hmm, so what if you want to run servers in vm's but don't want to involve your network administrator? Maybe one of the next 2 modes is for you... Internal Networking When you configure one or more vm's to sit on an Internal network, VirtualBox ensures that all traffic on that network stays within the host and is only visible to vm's on that virtual network. Configuration looks like this: The internal network ( in this example "intnet" ) is a totally isolated network and so is very "quiet". This is good for testing when you need a separate, clean network, and you can create sophisticated internal networks with vm's that provide their own services to the internal network. (e.g. Active Directory, DHCP, etc). Note that not even the Host is a member of the internal network, but this mode allows vm's to function even when the Host is not connected to a network (e.g. on a plane). Note that in this mode, VirtualBox provides no "convenience" services such as DHCP, so your machines must be statically configured or one of the vm's needs to provide a DHCP/Name service. Multiple internal networks are possible and you can configure vm's to have multiple NICs to sit across internal and other network modes and thereby provide routes if needed. But all this sounds tricky. What if you want an Internal Network that the host participates on with VirtualBox providing IP addresses to the Guests? Ah, then for this, you might want to consider Host-only Networking... Host-only Networking Host-only Networking is like Internal Networking in that you indicate which network the Guest sits on, in this case, "vboxnet0": All vm's sitting on this "vboxnet0" network will see each other, and additionally, the host can see these vm's too. However, other external machines cannot see Guests on this network, hence the name "Host-only". Logically, the network looks like this: This looks very similar to Internal Networking but the host is now on "vboxnet0" and can provide DHCP services. To configure how a Host-only network behaves, look in the VirtualBox Manager...Preferences...Network dialog: Port-Forwarding with NAT Networking Now you may think that we've provided enough modes here to handle every eventuality but here's just one more... What if you cart around a mobile-demo or dev environment on, say, a laptop and you have one or more vm's that you need other machines to connect into? And you are continually hopping onto different (customer?) networks. In this scenario: NAT - won't work because external machines need to connect in. Bridged - possibly an option, but does your customer want you eating IP addresses and can your software cope with changing networks? Internal - we need the vm(s) to be visible on the network, so this is no good. Host-only - same problem as above, we want external machines to connect in to the vm's. Enter Port-forwarding to save the day! Configure your vm's to use NAT networking; Add Port Forwarding rules; External machines connect to "host":"port number" and connections are forwarded by VirtualBox to the guest:port number specified. For example, if your vm runs a web server on port 80, you could set up rules like this:  ...which reads: "any connections on port 8080 on the Host will be forwarded onto this vm's port 80".  This provides a mobile demo system which won't need re-configuring every time you open your laptop lid. Summary VirtualBox has a very powerful set of options allowing you to set up almost any configuration your heart desires. For more information, check out the VirtualBox User Manual on Virtual Networking. -FB 

    Read the article

  • Ubunti 12.10 wake on lan not working with Realtek 8139

    - by f.cipriani
    My pc doesn't wake up when receiving a magic packet from a pc connected to the same router. ethtool: fcipriani@ubuntu:~$ sudo ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: MII PHYAD: 32 Transceiver: internal Auto-negotiation: on Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000007 (7) drv probe link Link detected: yes I have enabled all the wake up features in my bios, and I have verified the magic packet gets to the pc. I suspect the main problem is that the NIC light is completely turned off after the shutdown, but even after spending a lot of time researching I can't understand if this is a limit of my network card, my mobo, or something in the OS which needs to be configured correctly in order to leave the NIC in stand by mode with the light flashing. the NIC is Realtek 8139, the motherboard Asus P5L13L-X

    Read the article

  • how to access samba shares via nat?

    - by HSM
    I have setup a virtual machine in Virtual Box and installed a Samba Server. I changed the guest operating system's NIC from Bridged to NAT for a reason that I can't remember. I then added a additional NIC in "host only adapter" mode. The Windows host OS now can access the Ubuntu 10.10 virtual server via the Host Only NIC. However, I can not access the Samba server running on the Ubuntu guest OS. I am not sure what to do now. How can I get the widows Host OS to access the Guest OS' samba server.

    Read the article

  • Getting Started with Puppet on Oracle Solaris 11

    - by Glynn Foster
    One of the exciting enhancements with Oracle Solaris 11.2 has been the introduction of Puppet. While upstream Puppet did have some rudimentary support for Oracle Solaris 11, Drew Fisher and Ginnie Wray worked tirelessly to add enhance the Oracle Solaris Puppet offering. We've talked to customers over the past few years and asked them what their problems were and what technologies they were using, particularly for configuration management. Puppet came up time and time again, and it made a huge amount of sense bringing it as a 1st class citizen in the Oracle Solaris platform. So what is Puppet, and why is it useful? To quote from PuppetLabs, the guys who are responsible for creating Puppet: Puppet is a declarative, model-based approach to IT automation, helping you manage infrastructure throughout its lifecycle, from provisioning and configuration to orchestration and reporting. Using Puppet, you can easily automate repetitive tasks, quickly deploy critical applications, and proactively manage change, scaling from 10s of servers to 1000s, on-premise or in the cloud. What's more, with Puppet support for Oracle Solaris, administrators can now manage a completely heterogeneous data center from a single or series of Puppet masters. Better still, it's an excellent tool when combined with our new compliance framework to ensure you're meeting your compliance regulations. We're not stopping there of course, and we'll enhance our offerings over time, and work with PuppetLabs to get some of this support upstream (or into the Puppet Forge). So if you've heard some of the buzz around Puppet and never quite got started, and have some Oracle Solaris real estate that you'd love to manage, check out the Getting Started with Puppet on Oracle Solaris 11 guide.

    Read the article

  • Oracle Solaris at the OpenStack Summit in Atlanta

    - by Glynn Foster
    I had the fortune of attending my 2nd OpenStack summit in Atlanta a few weeks ago and it turned out to be a really excellent event. Oracle had many folks there this time around across a variety of different engineering teams - Oracle Solaris, Oracle ZFSSA, Oracle Linux, Oracle VM and more. Really great to see continuing momentum behind the project and we're very happy to be involved. Here's a list of the highlights that I had during the summit: The operators track was a really excellent addition, with a chance for users/administrators to voice their opinions based on experiences. Really good to hear how OpenStack is making businesses more agile, but also equally good to hear about some of the continuing frustrations they have (fortunately many of them are new and being addressed). Seeing this discussion morph into a "Win the enterprise" working group is also very pleasing. Enjoyed Troy Toman's keynote (Rackspace) about designing a planet scale cloud OS and the interoperability challenges ahead of us. I've been following some of the discussion around DefCore for a bit and while I have some concerns, I think it's mostly heading in the right direction. Certainly seems like there's a balance to strike to ensure that this effects the OpenStack vendors in such a way as to avoid negatively impacting our end users. Also enjoyed Toby Ford's keynote (AT&T) about his desire for a NVF (Network Function Virtualization) architecture. What really resonated was also his desire for OpenStack to start addressing the typical enterprise workload, being less like cattle and more like pets. The design summit was, as per usual, pretty intense for - definitely would get more value from these if I knew the code base a little better. Nevertheless, attended some really great sessions and got a better feeling of the roadmap for Juno. Markus Flierl gave a great presentation (see below) at the demo theatre for what we're doing with OpenStack on Oracle Solaris (and more widely at Oracle across different products). Based on the discussions that we had at the Oracle booth, there's a huge amount of interest there and we talked to some great customers during the week about their thoughts and directions in this respect. Undoubtedly Atlanta had some really good food. Highlights were the smoked ribs and brisket and the SweetWater brewing company. That said, I also loved the fried chicken, fried green tomatoes and collared greens, and wonderful hosting of "big momma" at Pitty Pat's Porch. Couldn't quite bring myself to eat biscuits and gravy in the morning though. Visiting the World of Coca-Cola just before flying out. A total brain washing exercise, but very enjoyable. And very much liked Beverly (contrary to many other opinions on the internet) - but then again, I'd happily drink tonic water every day of the year... Looking forward to Paris in November!

    Read the article

  • What happens after a packet is captured?

    - by Rayne
    Hi all, I've been reading about what happens after packets are captured by NICs, and the more I read, the more I'm confused. Firstly, I've read that traditionally, after a packet is captured by the NIC, it gets copied to a block of memory in the kernel space, then to the user space for whatever application that then works on the packet data. Then I read about DMA, where the NIC directly copies the packet into memory, bypassing the CPU. So is the NIC - kernel memory - User space memory flow still valid? Also, do most NIC (e.g. Myricom) use DMA to improve packet capture rates? Secondly, does RSS (Receive Side Scaling) work similarly in both Windows and Linux systems? I can only find detailed explanations on how RSS works in MSDN articles, where they talk about how RSS (and MSI-X) works on Windows Server 2008. But the same concept of RSS and MSI-X should still apply for linux systems, right? Thank you. Regards, Rayne

    Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >