Search Results

Search found 512 results on 21 pages for 'slave'.

Page 10/21 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

• Which hardware to VM ratio for Build-Server virtualization?

  - by Martin

  Let's start with saying that I'm a total noob wrt. to server virtualization. That is, I use VMs often during development, but they're simple desktop machine things for me. Now to my problem: We have two (physical) build servers, one master, one slave running Jenkins to do daily tasks and build (Visual C++ Builds) our release packages for our software. As such these machines are critical to our company, because we do lot's releases and without a controlled environment to create them, we can't ship fixes. (And currently there's no proper backup of these machines in place, because they do not hold any data as such - it just would be a major pain to setup them again should they go bust. (But setting up backup that I'd know would work in case of HW failure would even be more pain, so we have skipped that until now.)) Therefore (and for scaling purposes) we would like to go virtual with these machines. Outsourcing to the cloud is not an option, not at all, so we'll have to use on-premises hardware and VM hosts. Each Build-Server (master or slave) is a fully configured (installs, licenses, shares in case of the master, ...) Windows Server box. I would now ideally like to just convert the (two) existing physical nodes to VM images and run them. Later add more VM slave instances as clones of the existing ones. And here begin my questions: Should I go for one VM per one hardware-box or should I go for something where a single hardware runs multiple VMs? That would mean a single point of failure hardware wise and doesn't seem like a good idea ... or?? Since we're doing C++ compilation with Visual Studio, I assume that during a build the hardware (processor cores + disk) will be fully utilized, so going with more than one build-node per hardware doesn't seem to make much sense?? Wrt. to hardware options, does it make any difference which VM software we use (VMWare, MS, Virtualbox, ... ?) (We're using Windows exclusively for our builds.) Regarding budget: We have a normal small company (20 developers) budget for this. ;-) That is, if it's going to cost a few k$ it's going to cost. If it's free - the better. I strongly prefer solutions where there's no multi-k$ maintenance costs per year.

  Read the article

• How do I capture and playback http web requests against multiple web servers?

  - by KevM

  My overall goal is to not interrupt a production system while capturing HTTP Posts to a web application so that I can reverse engineer the telemetry coming from a closed application. I have control over the transmitter of the HTTP Posts but not the receiving web application. It seems like I need a request "forking" proxy. Sort of a reverse proxy that pushes the request to 2 endpoints, a master and slave, only relaying the response from the master endpoint back to the requester. I am not a server geek so something like this may exist but I don't know the term of art for what I am looking for. Another possibility could be a simple logging proxy. Capture a log of the web requests. Rewrite the log to target my "slave" web application. Playback the log with curl or something. Thank you for your assistance.

  Read the article

• How to divide work to a network of computers?

  - by Morpork

  Imagine a scenario as follows: Lets say you have a central computer which generates a lot of data. This data must go through some processing, which unfortunately takes longer than to generate. In order for the processing to catch up with real time, we plug in more slave computers. Further, we must take into account the possibility of slaves dropping out of the network mid-job as well as additional slaves being added. The central computer should ensure that all jobs are finished to its satisfaction, and that jobs dropped by a slave are retasked to another. The main question is: What approach should I use to achieve this? But perhaps the following would help me arrive at an answer: Is there a name or design pattern to what I am trying to do? What domain of knowledge do I need to achieve the goal of getting these computers to talk to each other? (eg. will a database, which I have some knowledge of, be enough or will this involve sockets, which I have yet to have knowledge of?) Are there any examples of such a system? The main question is a bit general so it would be good to have a starting point/reference point. Note I am assuming constraints of c++ and windows so solutions pointing in that direction would be appreciated.

  Read the article

• Software Architecture: How to divide work to a network of computers?

  - by Morpork

  Imagine a scenario as follows: Lets say you have a central computer which generates a lot of data. This data must go through some processing, which unfortunately takes longer than to generate. In order for the processing to catch up with real time, we plug in more slave computers. Further, we must take into account the possibility of slaves dropping out of the network mid-job as well as additional slaves being added. The central computer should ensure that all jobs are finished to its satisfaction, and that jobs dropped by a slave are retasked to another. The main question is: What approach should I use to achieve this? But perhaps the following would help me arrive at an answer: Is there a name or design pattern to what I am trying to do? What domain of knowledge do I need to achieve the goal of getting these computers to talk to each other? (eg. will a database, which I have some knowledge of, be enough or will this involve sockets, which I have yet to have knowledge of?) Are there any examples of such a system? The main question is a bit general so it would be good to have a starting point/reference point. Note I am assuming constraints of c++ and windows so solutions pointing in that direction would be appreciated.

  Read the article

• Running Ubuntu off a USB drive?

  - by Solignis

  I was wondering if a USB 2.0 Thumb drive has enough bandwidth to act as a primary system drive in an Ubuntu Linux server. More specifically an SAN server. I am running an iSCSI target, ZFS and NFS-kernel-server, BIND9 (Slave), and Openldap (Slave). I was thinking of resorting to a thumb drive because my new motherboard only has 4 SATA ports and I have 5 disks. 4 (ZFS Pool) 1 (System). And unless I get an expansion card there is no way to get more SATA ports. This "server" leans more twords a home server. I use in my lab with my VMware server. It provides storage, or atleast it did until it died. Would it still be better to go with the SATA hard disk?

  Read the article

• Big Data – Buzz Words: What is Hadoop – Day 6 of 21

  - by Pinal Dave

  In yesterday’s blog post we learned what is NoSQL. In this article we will take a quick look at one of the four most important buzz words which goes around Big Data – Hadoop. What is Hadoop? Apache Hadoop is an open-source, free and Java based software framework offers a powerful distributed platform to store and manage Big Data. It is licensed under an Apache V2 license. It runs applications on large clusters of commodity hardware and it processes thousands of terabytes of data on thousands of the nodes. Hadoop is inspired from Google’s MapReduce and Google File System (GFS) papers. The major advantage of Hadoop framework is that it provides reliability and high availability. What are the core components of Hadoop? There are two major components of the Hadoop framework and both fo them does two of the important task for it. Hadoop MapReduce is the method to split a larger data problem into smaller chunk and distribute it to many different commodity servers. Each server have their own set of resources and they have processed them locally. Once the commodity server has processed the data they send it back collectively to main server. This is effectively a process where we process large data effectively and efficiently. (We will understand this in tomorrow’s blog post). Hadoop Distributed File System (HDFS) is a virtual file system. There is a big difference between any other file system and Hadoop. When we move a file on HDFS, it is automatically split into many small pieces. These small chunks of the file are replicated and stored on other servers (usually 3) for the fault tolerance or high availability. (We will understand this in the day after tomorrow’s blog post). Besides above two core components Hadoop project also contains following modules as well. Hadoop Common: Common utilities for the other Hadoop modules Hadoop Yarn: A framework for job scheduling and cluster resource management There are a few other projects (like Pig, Hive) related to above Hadoop as well which we will gradually explore in later blog posts. A Multi-node Hadoop Cluster Architecture Now let us quickly see the architecture of the a multi-node Hadoop cluster. A small Hadoop cluster includes a single master node and multiple worker or slave node. As discussed earlier, the entire cluster contains two layers. One of the layer of MapReduce Layer and another is of HDFC Layer. Each of these layer have its own relevant component. The master node consists of a JobTracker, TaskTracker, NameNode and DataNode. A slave or worker node consists of a DataNode and TaskTracker. It is also possible that slave node or worker node is only data or compute node. The matter of the fact that is the key feature of the Hadoop. In this introductory blog post we will stop here while describing the architecture of Hadoop. In a future blog post of this 31 day series we will explore various components of Hadoop Architecture in Detail. Why Use Hadoop? There are many advantages of using Hadoop. Let me quickly list them over here: Robust and Scalable – We can add new nodes as needed as well modify them. Affordable and Cost Effective – We do not need any special hardware for running Hadoop. We can just use commodity server. Adaptive and Flexible – Hadoop is built keeping in mind that it will handle structured and unstructured data. Highly Available and Fault Tolerant – When a node fails, the Hadoop framework automatically fails over to another node. Why Hadoop is named as Hadoop? In year 2005 Hadoop was created by Doug Cutting and Mike Cafarella while working at Yahoo. Doug Cutting named Hadoop after his son’s toy elephant. Tomorrow In tomorrow’s blog post we will discuss Buzz Word – MapReduce. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Big Data, PostADay, SQL, SQL Authority, SQL Query, SQL Server, SQL Tips and Tricks, T SQL

  Read the article

• How to integrate Purify into Hudson CI?

  - by Martin

  Hello everybody! I have a Hudson CI system set up and for the moment it is used for building a project and running some unit tests. My next step is to integrate the memory leak detector Purify into the build cycle. Now I want to start the unit tests also inside purify and for this I have created a new batch task which runs following command: purify.exe /SaveTextData MyExecutable.exe --test TestLibrary.dll --output xml As I read in the Purify documentation the /SaveTextData option is used in order to run purify not in GUI mode. If I run this command on my local workstation in the command line it works perfectly. But in case it is started by Hudson, nothing happens. Unfortunetly there are no logs of purify... Has someone ever tried to start purify either by Hudson or any other CI system? Thanks in advance. Best regards Martin EDIT: I forgot to tell you, that I have Hudson running as master and slave on different computers. On the master I have configured a task which should start the unit tests within purify on the slave. I am running the slave via JNLP. EDIT 18.03.2010: Ok, so finally I am a bit closer the source of the problem. I have discovered, that running my unit tests in purify locally the log file EngineCmdLine.log contains three commands. I am starting purify with following command: purify.exe /SaveTextData TestRunnerConsoleWD.exe --test TestDemoWD.dll Output of EngineCmdLine.log when starting purify manually: File: D:\workspace\hudson\workspace\Purify_TestFW_CommonsCoreTest_Cpp_msvs9\TestRunnerConsoleWD.exe File: C:\WINDOWS\system32\ws2_32.dll File: D:\workspace\hudson\workspace\Purify_TestFW_CommonsCoreTest_Cpp_msvs9\TestDemoWD.dll Output when starting via Hudson: File: D:\workspace\hudson\workspace\Purify_TestFW_CommonsCoreTest_Cpp_msvs9\TestRunnerConsoleWD.exe File: C:\WINDOWS\system32\ws2_32.dll File: D:\workspace\hudson\workspace\Purify_TestFW_CommonsCoreTest_Cpp_msvs9\TestDemoWD.dll File: D:\workspace\hudson\workspace\Purify_TestFW_CommonsCoreTest_Cpp_msvs9\TestDemoWD.dll The error output of purify: Instrumenting: BtcTestDemoWD.dll 313856 bytes Purify: While processing file D:\workspace\hudson\workspace\Purify_TestFW_CommonsCoreTest_Cpp_msvs9\TESTFWWD.DLL: Error: Cannot replace file c:\Programme\IBM\RationalPurifyPlus\PurifyPlus\cache\BTCTESTFWWD$Purify_D_workspace_hudson_workspace_Purify_TestFW_CommonsCoreTest_Cpp_msvs9.DLL. Is it in use? TESTFWWD.DLL 505344 bytes Unable to instrument D:\workspace\hudson\workspace\Purify_TestFW_CommonsCoreTest_Cpp_msvs9\TestDemoWD.dll (0x1) Question is, why is purify starting twice a command with the TestDemoWD.dll library?

  Read the article

• post commit hook fail

  - by jarad mayers

  I have Master/Slave setup using Win2k8R with SVN 1.6.9 and using TortoiseSVN 1.6.7. The access is through Apache and using http. Everything works but when I commit I get the following message: Error: post-commit hook failed (exit code 1) with output: Error: The process cannot access the file because it is being used by another process. This happen when using multiple TortoiseSVN dialog for committing the files in rapid succession. If I use one TortoiseSVN dialog and wait till the commit reply is back then I won't see the problem. In other words, committing one at the time cause no issue. The post-commit script output is logged. Even though I get the above error but when I check the Master and Slave repository the files have been replicated okay with no issue. I am wondering how this issue can be solved.

  Read the article

• Workflow for statistical analysis and report writing

  - by ws

  Does anyone have any wisdom on workflows for data analysis related to custom report writing? The use-case is basically this: Client commissions a report that uses data analysis, e.g. a population estimate and related maps for a water district. The analyst downloads some data, munges the data and saves the result (e.g. adding a column for population per unit, or subsetting the data based on district boundaries). The analyst analyzes the data created in (2), gets close to her goal, but sees that needs more data and so goes back to (1). Rinse repeat until the tables and graphics meet QA/QC and satisfy the client. Write report incorporating tables and graphics. Next year, the happy client comes back and wants an update. This should be as simple as updating the upstream data by a new download (e.g. get the building permits from the last year), and pressing a "RECALCULATE" button, unless specifications change. At the moment, I just start a directory and ad-hoc it the best I can. I would like a more systematic approach, so I am hoping someone has figured this out... I use a mix of spreadsheets, SQL, ARCGIS, R, and Unix tools. Thanks! PS: Below is a basic Makefile that checks for dependencies on various intermediate datasets (w/ ".RData" suffix) and scripts (".R" suffix). Make uses timestamps to check dependencies, so if you 'touch ss07por.csv', it will see that this file is newer than all the files / targets that depend on it, and execute the given scripts in order to update them accordingly. This is still a work in progress, including a step for putting into SQL database, and a step for a templating language like sweave. Note that Make relies on tabs in its syntax, so read the manual before cutting and pasting. Enjoy and give feedback! http://www.gnu.org/software/make/manual/html%5Fnode/index.html#Top R=/home/wsprague/R-2.9.2/bin/R persondata.RData : ImportData.R ../../DATA/ss07por.csv Functions.R $R --slave -f ImportData.R persondata.Munged.RData : MungeData.R persondata.RData Functions.R $R --slave -f MungeData.R report.txt: TabulateAndGraph.R persondata.Munged.RData Functions.R $R --slave -f TabulateAndGraph.R report.txt

  Read the article

• What's the standard algorithm for syncing two lists of objects?

  - by Oliver Giesen

  I'm pretty sure this must be in some kind of text book (or more likely in all of them) but I seem to be using the wrong keywords to search for it... :( A common task I'm facing while programming is that I am dealing with lists of objects from different sources which I need to keep in sync somehow. Typically there's some sort of "master list" e.g. returned by some external API and then a list of objects I create myself each of which corresponds to an object in the master list. Sometimes the nature of the external API will not allow me to do a live sync: For instance the external list might not implement notifications about items being added or removed or it might notify me but not give me a reference to the actual item that was added or removed. Furthermore, refreshing the external list might return a completely new set of instances even though they still represent the same information so simply storing references to the external objects might also not always be feasible. Another characteristic of the problem is that both lists cannot be sorted in any meaningful way. You should also assume that initializing new objects in the "slave list" is expensive, i.e. simply clearing and rebuilding it from scratch is not an option. So how would I typically tackle this? What's the name of the algorithm I should google for? In the past I have implemented this in various ways (see below for an example) but it always felt like there should be a cleaner and more efficient way. Here's an example approach: Iterate over the master list Look up each item in the "slave list" Add items that do not yet exist Somehow keep track of items that already exist in both lists (e.g. by tagging them or keeping yet another list) When done iterate once more over the slave list Remove all objects that have not been tagged (see 4.) Update Thanks for all your responses so far! I will need some time to look at the links. Maybe one more thing worthy of note: In many of the situations where I needed this the implementation of the "master list" is completely hidden from me. In the most extreme cases the only access I might have to the master list might be a COM-interface that exposes nothing but GetFirst-, GetNext-style methods. I'm mentioning this because of the suggestions to either sort the list or to subclass it both of which is unfortunately not practical in these cases unless I copy the elements into a list of my own and I don't think that would be very efficient. I also might not have made it clear enough that the elements in the two lists are of different types, i.e. not assignment-compatible: Especially, the elements in the master list might be available as interface references only.

  Read the article

• How to generate Doctrine models/classes that extend a custom record class

  - by Shane O'Grady

  When I use Doctrine to generate classes from Yaml/db each Base class (which includes the table definition) extends the Doctrine_Record class. Since my app uses a master and (multiple) slave db servers I need to be able to make the Base classes extend my custom record class to force writes to go to the master db server (as described here). However if I change the base class manually I lose it again when I regenerate my classes from Yaml/db using Doctrine. I need to find a way of telling Doctrine to extend my own Base class, or find a different solution to a master/slave db setup using Doctrine. Example generated model: abstract class My_Base_User extends Doctrine_Record { However I need it to be automatically generated as: abstract class My_Base_User extends My_Record { I am using Doctrine 1.2.1 in a new Zend Framework 1.9.6 application if it makes any difference.

  Read the article

• Any way to select without causing locking in MySQL?

  - by Shore

  Query: SELECT COUNT(online.account_id) cnt from online; But online table is also modified by an event, so frequently I can see lock by running show processlist. Is there any grammar in MySQL that can make select statement not causing locks? And I've forgotten to mention above that it's on a MySQL slave database. After I added into my.cnf:transaction-isolation = READ-UNCOMMITTED the slave will meet with error: Error 'Binary logging not possible. Message: Transaction level 'READ-UNCOMMITTED' in InnoDB is not safe for binlog mode 'STATEMENT'' on query So, is there a compatible way to do this?

  Read the article

• How communicate with pty via minicom or screen?

  - by gscott2112

  I am trying to provide an AT/Modem-like interface around some hardware. Follwing this post I have the server setting up a pty using openpty(). Now I can communicate with the server as expected with a client app that open the slave and communicates via read() and write() calls. However I would also like to be able to use either the screen command or minicom to issue commands by hand to the slave. However the server never seems to receive any data when trying to do this. Is there something significant I am missing with this approach?

  Read the article

• Git doesn't sync files until committed, even if checked out in a different branch

  - by DertWaiter

  Okay, I have git 1.7.11.1 on Windows and I have a local test repository with 2 branches. One is master with index.php and help.php. I then create another branch called slave :) I run from git bash rm help.php and it disappears from the folder, but I don't stage anything. I switch to checkout master branch and it is supposed to restore file help.php because it is not modified in the master branch, isn't it? And it does not do it. When I go back to the slave branch and commit and then switch to checkout master then help.php appears. Is that the way it is supposed to to work? Why?

  Read the article

• How can I configure a Hudson job to use a specific JDK?

  - by rewbs

  I have a number of projects running on a Hudson slave. I'd like one of them to run Ant under Java6, rather than the default (which is Java5 in my environment). In the project configuration view, I was hoping to find either: An explicit option allowing me to set a custom JDK location to use for this project. A way to set custom environment variables for this project, which would allow me to set JAVA_HOME to the JDK6 location. The would make Ant pick up and run on Java6 as desired. Is there a way to do either of the above? If one of those facilities is available, I can't see how to access it. I'm running on Hudson 1.285. I would rather avoid using an "execute shell" operation instead of the "invoke Ant" operation if possible: my slave is on z/OS and Hudson doesn't seem to create the temporary shell scripts properly on this platform (probably an encoding issue).

  Read the article

• Looking for python lib to manage remote tasks

  - by Riz

  Hi, I have server with django on it, this server runs some manage.py commands and update database. Now I need to move some of this tasks to different servers. I don't want to allow remote db access and need some tool\lib to be able to start task on remote servers by main server's command and update tasks code/add new tasks. I have ssh access to every server, all servers run under debian and all code in python. I was thiking about creating my own xmpp based solution(server sends messages to slave servers with commands to execute, like "update task", "run task"), or maybe some low-level ssh based solution where main server logs to slave servers and executes bash commands. But I would be happy to hear any advices.

  Read the article

• How to use XDMCP+GDM and Xnest?

  - by João Pinto

  I have been trying to enable XDMCP on GDM without much success. Following some instructions I have edited /etc/gdm/custom.conf and added: [daemon] RemoteGreeter=/usr/lib/gdm/gdm-xdmcp-chooser-slave [xdmcp] Enable=true Then restarted gdm and tried to connect both locally and from a remote system with: Xnest :1 -query localhost Xnest :1 -query remote_system_hostname I just get a black screen instead of the GDM window as expected. I am missing something ?

  Read the article

• Setting MTU on Exalogic

  - by csoto

  For many reasons, a system administrator may want to change the MTU settings of a server. But in a system like Exalogic which contains lots of interconnected nodes and other various components, it's important to understand how this applies to the different networks. For example, when bringing up bonding of InfiniBand an error like the following may be thrown: Bringing up interface bond1: SIOCSIFMTU: Invalid argument Both scripts ifcfg-ib0 and ifcfg-ib1 (from the /etc/sysconfig/network-scripts/ direectory) have MTU set to 65500, which is a valid MTU value only if all IPoIB slaves operate in connected mode and are configured with the same value, so the line below must be added to both network scripts and then restart the network: CONNECTED_MODE=yes By the way, an error of the form “SIOCSIFMTU: Invalid argument” indicates that the requested MTU was rejected by the kernel. Typically this would be due to it exceeding the maximum value supported by the interface hardware. In that case you must either reduce the MTU to a value that is supported or obtain more capable hardware. This problem has been seen when trying to modify the MTU using the ifconfig command, like the output of the example below: [root@elxxcnxx ~]# ifconfig ib1 mtu 65520 SIOCSIFMTU: Invalid argument It's important to insist that in most cases the nodes must be rebooted after the MTU size has been changed. Although in some circumstances it may work without a reboot, it is not how it is typically documented. Now, in order to achieve a reduced memory consumption and improve performance for network traffic received on IPoIB related interfaces, it is recommend to reduce the MTU value in interface configuration files for IPoIB related bonds from 65520 to 64000. The change needs to be made to interface configuration files under the /etc/sysconfig/network-scripts directory and applies to the interface configuration files for bonds over IPoIB related slave devices, for example /etc/sysconfig/network-scripts/ifcfg-bond1. However, keep in mind that the numeric portion of the interface filenames that corresponding to IPoIB interfaces is expected to vary across compute nodes and vServers and so cannot be relied upon to identify which interface files are for bonds are over IPoIB rather than EoIB related slave interfaces. To fix these MTU values to the recommended settings, there are very useful instructions and a script on the MOS Note 1624434.1, and it's applicable physical and virtual configurations of Exalogic. Regarding the recommended MTU value for EoIB related interfaces, its maximum appropriate value is 1500. If for some reason a vServer has been created with a higher value (set on the /etc/sysconfig/network-scripts/ifcfg-bond0 file), then it must be fixed. An error like the following could be thrown under this circumstance: [root@vServer ~]# service network restart ... Bringing up interface bond0:  SIOCSIFMTU: Invalid argument Also an error like the one below can be seen on the /var/log/messages file of the vServer: kernel: T5074835532 [mlx4_vnic] eth1:vnic_change_mtu:360: failed: new_mtu 64000 2026 The MOS Note 1611657.1 is very useful for this purpose.

  Read the article

• Botnet Malware Sleeps Eight Months Activation, Child Concerns

  Daily Safety Check experts used a computer forensic analysis of a significant botnet that consisted of Carberp and SpyEye malware to come up with the details for their report. The analysis found that the botnet profiled the behavior of the slave computers it infected, similar to surveillance techniques used by law enforcement agencies, for an average of eight months. During the eight months, the botnet analyzed each computer's users and assigned ratings to certain activities to form a complete profile for each. Doing so allowed those behind the scheme to determine which were the most favora...

  Read the article

• Is a 1:* write:read thread system safe?

  - by Di-0xide

  Theoretically, thread-safe code should fix race conditions. Race conditions, as I understand it, occur because two threads attempt to write to the same location at the same time. However, what about a threading model in which a single thread is designed to write to a location, and several slave/worker threads simply read from the location? Assuming the value/timing at which they read the data isn't relevant/doesn't hinder the worker thread's outcome, wouldn't this be considered 'thread safe', or am I missing something in my logic?

  Read the article

• mysqld crashes on any statement

  - by ??iu

  I restarted my slave to change configuration settings to skip reverse hostname lookup on connecting and to enable the slow query log. I edited /etc/my.cnf making only these changes, then restarted mysqld with /etc/init.d/mysql restart All appeared to be well but when I connect to msyqld remotely or locally though it connects okay a slight problem is that mysqld crashes whenever you try to issue any kind of statement. The client looks like: Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 3 Server version: 5.1.31-1ubuntu2-log Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show tables; ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... Connection id: 1 Current database: mydb ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away Bus error The mysqld error log looks like: 101210 16:35:51 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:35:51 InnoDB: Assertion failure in thread 140245598570832 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:35:51 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=3 max_threads=600 threads_connected=3 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18209220 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f8d791580d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f902a76a080] /lib/libc.so.6(gsignal+0x35) [0x7f90291f8fb5] /lib/libc.so.6(abort+0x183) [0x7f90291fabc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f902a7623ba] /lib/libc.so.6(clone+0x6d) [0x7f90292abfcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18213c70 = thd->thread_id=3 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:35:51 mysqld_safe Number of processes running now: 0 101210 16:35:51 mysqld_safe mysqld restarted InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 101210 16:35:54 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 101210 16:35:56 InnoDB: Started; log sequence number 456 143528628 101210 16:35:56 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 16:35:56 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 16:35:56 [Note] Event Scheduler: Loaded 0 events 101210 16:35:56 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 16:36:11 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:36:11 InnoDB: Assertion failure in thread 139955151501648 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:36:11 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18588720 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f49d916f0d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f4c8a73f080] /lib/libc.so.6(gsignal+0x35) [0x7f4c891cdfb5] /lib/libc.so.6(abort+0x183) [0x7f4c891cfbc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f4c8a7373ba] /lib/libc.so.6(clone+0x6d) [0x7f4c89280fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18599950 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:36:11 mysqld_safe Number of processes running now: 0 101210 16:36:11 mysqld_safe mysqld restarted The config is [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_file_per_table innodb_buffer_pool_size=10G innodb_log_buffer_size=4M innodb_flush_log_at_trx_commit=2 innodb_thread_concurrency=8 skip-slave-start server-id=3 # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /DB2/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 128K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP max_connections = 600 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 32M # skip-federated slow-query-log skip-name-resolve Update: I followed the instructions as per http://dev.mysql.com/doc/refman/5.1/en/forcing-innodb-recovery.html and set innodb_force_recovery = 4 and the logs are showing a different error but the behavior is still the same: 101210 19:14:15 mysqld_safe mysqld restarted 101210 19:14:19 InnoDB: Started; log sequence number 456 143528628 InnoDB: !!! innodb_force_recovery is set to 4 !!! 101210 19:14:19 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 19:14:19 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 19:14:19 [Note] Event Scheduler: Loaded 0 events 101210 19:14:19 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 19:14:32 InnoDB: error: space object of table mydb/__twitter_friend, InnoDB: space id 1602 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/access_request, InnoDB: space id 1318 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/activity, InnoDB: space id 1595 did not exist in memory. Retrying an open. 101210 19:14:32 - mysqld got signal 11 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x1753c070 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f7a0b5800d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f7cbc350080] /usr/sbin/mysqld(ha_innobase::innobase_get_index(unsigned int)+0x46) [0x77c516] /usr/sbin/mysqld(ha_innobase::innobase_initialize_autoinc()+0x40) [0x77c640] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x3f3) [0x781f23] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f7cbc3483ba] /lib/libc.so.6(clone+0x6d) [0x7f7cbae91fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x1754d690 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash.

  Read the article

• award phoenix bios not recognizing my sata hdd.

  - by josh

  What am I doing wrong? I have a custom built comp with a Fatal1ty AA8XE mobo. It has 4 SATA ports and one IDE port. When i first got it, I had a really hard time putting in more than one hard drive. Right now i have one 120gb IDE HDD on master and my DVD+-RW on slave connected to the one IDE spot on the mobo. I ripped a bunch of movies and filled up my HDD, so I got a WD 80gb SATA drive. I plugged it into SATA1 and hooked up the power, turned on comp, went into bios. The only thing in any option in any of the menues in this crazy lookin bios is a thing that says "SATA mode". i put it on IDE, set it so PATA is primary, SATA is secondary. booted up my comp, nothin. Not recognizing the SATA. I went back into the bios and checked it all again. I saw that it says SATA2 and SATA4 are the secondaries so i put it on SATA2, booted, nothing, same with SATA4, same with SATA3, all same as SATA1. Bios and wt os are not recognizing the drive as being there at all. I even downloaded and printed the almost 100 page manual for the mobo, read the entire thing, and still can't figure it out. I know there are a lot of people out there smarter than me when it comes to computers. So please, somebody, anybody, please tell me something that I'm not seeing. Some setting somewhere that I didn't configure right. There is something, obviously, but I can't find it. As far as i can tell, everything is set perfectly fine for my 120gb to be the master and the SATA to be the slave. I don't know what I'm doing wrong but I'm seriously about to throw this computer out the window. thankyou in advance to whoever attempts to help.

  Read the article

• MySQL-Cluster or Multi-Master for production? Performance issues?

  - by Phillip Oldham

  We are expanding our network of webservers on EC2 to a number of different regions and currently use master/slave replication. We've found that over the past couple of months our slave has stopped replicating a number of times which required us to clear the db and initialise the replication again. As we're now looking to have servers in 3 different regions we're a little concerned about these MySQL replication errors. We believe they're due to auto_increment values, so we're considering a number of approaches to quell these errors and stabilise replication: Multi-Master replication; 3 masters (one in each region), with the relevant auto_increment offsets, regularly backing up to S3. Or, MySQL-Cluster; 3 nodes (one in each region) with a separate management node which will also aggregate logs and statistics. After investigating it seems they both have down-sides (replication errors for the former, performance issues for the latter). We believe the cluster approach would allow us to manage and add new nodes more easily than the Multi-Master route, and would reduce/eliminate the replication issues we're currently seeing. But performance is a priority. Are the performance issues of MySQL-Cluster as bad as people say?

  Read the article

• Accounting setup in freeradius with mikrotik and the "always" module

  - by Matt

  I have a freeradius setup that is being used to provide authentication for users on a wireless network. The access points are all Mikrotik hardware and the users are connected 24/7. We've been using Daloradius with mysql and freeradius 2. The boss wants to use the accounting information and while this is all set up and appears to be working, I've found that not all the accounting information is present. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly. So he started poking around at this link: http://wiki.mikrotik.com/wiki/RouterOs_MySql_Freeradius#Configuring_RouterOs_for_Radius_.26_PPP.2A_AAA And was looking specifically at the following section. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } However, that link references freeradius 1 and I can't find this in the radius.conf file for freeradius 2. What does it do and could it be a reason I'm missing data? EDIT: I have found one issue. We have a backup freeradius server that is also receiving the accounting packets. Although they are replicating, it's only a master/slave configuration. If the slave receives accounting packets it won't replicate them back to the master. Although I suspect this might solve it, the boss is not convinced due to the always module. Is there anything special I need to configure in the mikrotik AP's or freeradius 2 for clients connected 24/7.

  Read the article

• AuthBasicProvider: failover not working when the first LDAP is down?

  - by quanta

  I've been trying to setup redundant LDAP servers with Apache 2.2.3. /etc/httpd/conf.d/authn_alias.conf <AuthnProviderAlias ldap master> AuthLDAPURL ldap://192.168.5.148:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> <AuthnProviderAlias ldap slave> AuthLDAPURL ldap://192.168.5.199:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> /etc/httpd/conf.d/authz_ldap.conf # # mod_authz_ldap can be used to implement access control and # authenticate users against an LDAP database. # LoadModule authz_ldap_module modules/mod_authz_ldap.so <IfModule mod_authz_ldap.c> <Location /> AuthBasicProvider master slave AuthzLDAPAuthoritative Off AuthType Basic AuthName "Authorization required" AuthzLDAPMemberKey member AuthUserFile /home/setup/svn/auth-conf AuthzLDAPSetGroupAuth user require valid-user AuthzLDAPLogLevel error </Location> </IfModule> If I understand correctly, mod_authz_ldap will try to search users in the second LDAP if the first server is down or OpenLDAP on it is not running. But in practice, it does not happen. Tested by stopping LDAP on the master, I get the "500 Internal Server Error" when accessing to the Subversion repository. The error_log shows: [11061] auth_ldap authenticate: user quanta authentication failed; URI / [LDAP: ldap_simple_bind_s() failed][Can't contact LDAP server] Did I misunderstand?

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >