Search Results

Search found 788 results on 32 pages for 'tx'.

Page 10/32 | < Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >

• Network problems with Ubuntu on VMware

  - by svick

  I'm running Ubuntu 10.04 inside VMware Player running under Windows Vista and I can't connect to the internet or the host computer from the Ubuntu. I have set all the VMware services to “manual” (like VMware DHCP Service), but starting them manually doesn't help. In VMware, the network seems to work (there is a green dot beside the network icon) and I have tried both Bridged and NAT settings. ifconfig doesn't show the eth1 interface, unless I give it as a parameter (or use -a). I think this means that Ubuntu thinks that the network isn't connected at all. How do I fix this? ifconvadmin@ubu1004:~$ ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:56 errors:0 dropped:0 overruns:0 frame:0 TX packets:56 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:4192 (4.1 KB) TX bytes:4192 (4.1 KB) vadmin@ubu1004:~$ ifconfig eth1 eth1 Link encap:Ethernet HWaddr 00:0c:29:2d:a0:6f BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:18 Base address:0x2000

  Read the article

• EC2 instance is blocking all outbound connections, how to diagnose/fix?

  - by Fraggle

  My EC2 instance is blocking all outbound connections. wget http://www.google.com ==> Hangs ping google.com ==>hangs ssh user@anyserver ==>hangs I ran : sudo iptables -F to eliminate all rules to no avail AWS Management console shows Security Group for that instance has Inbound rule allowing ssh and port 80. Can't find anything about Outbound rules there. Rebooted instance, no change. If anyone knows how to diagnose or fix, please help. Adding info: [ec2-user@ip-10-112-62-73 ~]$ ifconfig eth0 Link encap:Ethernet HWaddr 12:31:3D:06:31:BB inet addr:10.112.62.73 Bcast:10.112.63.255 Mask:255.255.254.0 inet6 addr: fe80::1031:3dff:fe06:31bb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1933 errors:0 dropped:0 overruns:0 frame:0 TX packets:1764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:164075 (160.2 KiB) TX bytes:343256 (335.2 KiB) Interrupt:9 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:672 (672.0 b) TX bytes:672 (672.0 b) [ec2-user@ip-10-112-62-73 ~]$ ip route show 10.112.62.0/23 dev eth0 proto kernel scope link src 10.112.62.73 default via 10.112.62.1 dev eth0

  Read the article

• Change the order of IP addresses returned by ifconfig?

  - by erikcw

  I have an Ubuntu server with several IP addresses attached to it. 127.0.0.1 is listed as venet0 by ifconfig. I'm using Chef to configure the server. The problem is that chef is listing 127.0.0.1 as the IP address for the server instead of one of the server's "real" IPs. (apparent "ohai ipaddress" uses the first IP listed by ifconfig to determine the server's IP). How can I change the order so the servers main IP is listed first instead of the 127.0.0.1? Can venet0 be deleted and venet0:0 be "promoted" to take its place since 127.0.0.1 is already listed in the "lo" interface? lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:16700 (16.7 KB) TX bytes:16700 (16.7 KB) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.1 P-t-P:127.0.0.1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:7622207 errors:0 dropped:0 overruns:0 frame:0 TX packets:8183436 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2102750761 (2.1 GB) TX bytes:2795213667 (2.7 GB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX1 P-t-P:XXX.XXX.XXX.XX1 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:XXX.XXX.XXX.XX2 P-t-P:XXX.XXX.XXX.XX2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 route -n route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.0.2.1 0.0.0.0 255.255.255.255 UH 0 0 0 venet0 0.0.0.0 192.0.2.1 0.0.0.0 UG 0 0 0 venet0

  Read the article

• Amazon EC2 instance missing Network Interface

  - by Sergiks

  I am running Linux on a t1.micro instance at Amazon EC2. Once I noticed bruteforce ssh login attemtps from a certain IP, after litle Googling I issued the two following commands (other ip): iptables -A INPUT -s 202.54.20.22 -j DROP iptables -A OUTPUT -d 202.54.20.22 -j DROP Either this, or maybe some other actions like yum upgrade perhaps, caused the follwing fiasco: after rebooting the server, it came up without the Network Interface! I only can connect to it through AWS Management Console JAVA ssh client - via local 10.x.x.x address. Console's Attach Network Interface as well as Detach.. are greyed out for this instance. Network Interfaces item at the left does not offer any Subnets to choose from, to create a new N.I. Please advice, how can I recreate a Network Interface for the instance? Upd. The instance is not accessible from outside: cannot be pinged, SSH'ed or connected by HTTP on port 80. Here's the ifconfig output: eth0 Link encap:Ethernet HWaddr 12:31:39:0A:5E:06 inet addr:10.211.93.240 Bcast:10.211.93.255 Mask:255.255.255.0 inet6 addr: fe80::1031:39ff:fe0a:5e06/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1426 errors:0 dropped:0 overruns:0 frame:0 TX packets:1371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:152085 (148.5 KiB) TX bytes:208852 (203.9 KiB) Interrupt:25 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) What is also unusual: a new micro instance I created from scratch, with no relation to the troubled one, was not pingable too.

  Read the article

• debian 6 losing a large amount of packets

  - by Sc0rian

  I have a rather strange problem. We covered all the obvious hardware related issues (different nic, eth cable and switch) however I cannot seem to stop eth dropping packets. I have 4 servers all exactly the same. driver: e1000e version: 1.2.20-k2 firmware-version: 1.8-0 bus-info: 0000:06:00.0 They are all running the latest kernel(2.6.32-5-amd64). However they do this: RX packets:17073870634 errors:0 dropped:14147208 overruns:0 frame:0 another server: eth0 Link encap:Ethernet HWaddr e0:69:95:05:2f:cb inet addr:10.10.10.86 Bcast:10.10.10.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5455209277 errors:0 dropped:375445 overruns:0 frame:0 TX packets:3666134366 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6688414486673 (6.0 TiB) TX bytes:1611812171539 (1.4 TiB) Interrupt:20 Memory:d0600000-d0620000 eth1 Link encap:Ethernet HWaddr 00:1b:21:b7:7a:ce inet addr:10.10.0.86 Bcast:10.10.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15473695728 errors:0 dropped:5808325 overruns:0 frame:0 TX packets:20112364421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9192378766434 (8.3 TiB) TX bytes:20216368266761 (18.3 TiB) Interrupt:17 Memory:d0280000-d02a0000 A massive amount of dropped packets. I have tried to load on the latest driver, 1.9.5. This did nothing. I'm not sure what else to do.

  Read the article

• Configure static IPv6 on Ubuntu

  - by Charles Offenbacher

  I'm trying to configure IPv6 on a dedicated Ubuntu server. My provider gave me a "/64" (whatever that is - I'm still confused) of IPv6 addresses. However, when I try to use them, I can't ping anything. What do I do? :( # ping6 ipv6.google.com PING ipv6.google.com(vx-in-x63.1e100.net) 56 data bytes From fe80::219:d1ff:fefb:42d8 icmp_seq=1 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=2 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2014ms # tracepath6 ipv6.google.com 1?: [LOCALHOST] 0.025ms pmtu 1500 1: fe80::219:d1ff:fefb:42d8%eth0 2000.022ms !H Resume: pmtu 1500 # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 64.***.***.*** netmask 255.255.255.248 gateway 64.***.***.*** iface eth0 inet6 static pre-up modprobe ipv6 address 2607:F878:1:***::1 netmask 64 gateway 2607:F878:1:***(same as address)::1 # ifconfig eth0 Link encap:Ethernet HWaddr 00:19:d1:fb:42:d8 inet addr:64.***.***.*** Bcast:64.***.***.*** Mask:255.255.255.248 inet6 addr: fe80::219:d1ff:fefb:42d8/64 Scope:Link inet6 addr: 2607:f878:1:***::1/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:52451 errors:0 dropped:0 overruns:0 frame:0 TX packets:39729 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6817761 (6.8 MB) TX bytes:6153835 (6.1 MB) Interrupt:41 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:166 errors:0 dropped:0 overruns:0 frame:0 TX packets:166 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31714 (31.7 KB) TX bytes:31714 (31.7 KB)

  Read the article

• bond0:0 + define virtual IP

  - by yael

  hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• bond0:0 + define virtual IP

  - by yael

  hi all in my linux server I have the follwoing: Linux Version - RedHat-Linux- 5.3.0.0 (this linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it posible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• IPTables forward from only one ip on my server

  - by user1307079

  I was able to get my server to forward connections on a certain port to a different IP, but when I add -d to specify an IP to froward from, It does not work. This is what I am trying, iptables -t nat -A PREROUTING -d 173.208.230.107 -p tcp --dport 80 iptables -t nat -nvL-j DNAT --to-destination 38.105.20.226:80. It works fine without the -d. Here is my ifconfig dump: em1 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.106 Bcast:173.208.230.111 Mask:255.255.255.248 inet6 addr: fe80::2a0:d1ff:feed:d054/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:100058 errors:0 dropped:0 overruns:0 frame:0 TX packets:18941701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:12779711 (12.1 MiB) TX bytes:825498499 (787.2 MiB) Memory:fbde0000-fbe00000 em1:9 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.107 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:10 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.108 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:11 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.109 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 em1:12 Link encap:Ethernet HWaddr 00:A0:D1:ED:D0:54 inet addr:173.208.230.110 Bcast:173.208.230.111 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fbde0000-fbe00000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)

  Read the article

• Route web traffic through a separate iterface

  - by tkane

  I'd like to route web traffic through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• SSH Connection Error : No route to host

  - by dewbot

  There are three machines in this scenario: Desktop A : [email protected] Laptop A : [email protected] Machine B : [email protected] All the machines have Ubuntu 11.04 (Desktop A is a 64bit one) and have both openssh-server and openssh-client. Now when I try to connect Desktop A to Laptop A or vice-versa by ssh [email protected] I get an error as port 22: No route to host in both the cases. I own both the machines, now if I try same commands from my friend's machine, i.e. via Desktop B, I can access both my Laptop and Desktop. But if I try to access Desktop B from my Laptop or by Desktop I get port 22: Connection timed out I even tried changing ssh port no. in ssh_config file but no success. Note: that 'Laptop A' uses WiFi connection while 'Machine A' uses Ethernet Connection and 'Machine B' is on an entirely different network. Laptop A && Desktop A - Router/Nano_Rcvr provided to me by ISP. So to one Router two Machines are connected and can be accessed at the same time. here is my ifconfig output for both the machines :- Laptop wlan0 Link encap:Ethernet HWaddr X:X:X:X:00:bc inet addr:1.23.73.111 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::219:e3ff:fe04:bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:108409 errors:0 dropped:0 overruns:0 frame:0 TX packets:82523 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:44974080 (44.9 MB) TX bytes:22973031 (22.9 MB) Desktop eth0 Link encap:Ethernet HWaddr X:X:X:X:c5:78 inet addr:1.23.68.209 Bcast:1.23.95.255 Mask:255.255.224.0 inet6 addr: fe80::227:eff:fe04:c578/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10380 errors:0 dropped:0 overruns:0 frame:0 TX packets:4509 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1790366 (1.7 MB) TX bytes:852877 (852.8 KB) Interrupt:43 Base address:0x2000

  Read the article

• Ubuntu - wireless connection works great but wired is totally dead

  - by Dan

  I am running Ubuntu 10.04 on my Acer Aspire One netbook. The wireless connection works great, but the wired is totally dead. When I plug the Ethernet wire, the little led next to the port doesn't blink. If I do ifconfig, this is the output: lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1659 errors:0 dropped:0 overruns:0 frame:0 TX packets:1659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:132304 (132.3 KB) TX bytes:132304 (132.3 KB) wlan0 Link encap:Ethernet HWaddr 18:f4:6a:65:48:1f inet addr:192.168.1.7 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::1af4:6aff:fe65:481f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:94823 errors:0 dropped:0 overruns:0 frame:0 TX packets:81390 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:93028474 (93.0 MB) TX bytes:18002558 (18.0 MB) There is no eth0. Is that normal? In the "Network Connections" GUI there is an entry "Wired connection 1", its "MAC address" field is blank. How can I make the wired connection work?

  Read the article

• "Network is unreachable" When pinging google, can connect to internal computers on debian VM

  - by musher

  Similar to this SU question: "Network is unreachable" when attempting to ping google, but internal addresses work Actually, it's pretty much the same base issue. I went through that thread trying to find a solution, I changed my resolv.conf: before: domain [my work domain] search [my work domain] nameserver [my gateway] nameserver [my gateway2] I changed it to: after: domain [my work domain] search [my work domain] nameserver 8.8.8.8 nameserver 8.8.4.4 However, any time I reboot the computer the resolv.conf gets overwritten to the previous version (the 'before' above). The issues began after I installed virtualbox additions, X server and (specifically) LXDE: Cat of apt history.log: Start-Date: 2014-08-21 10:03:42 Commandline: apt-get install virtualbox-guest-utils virtualbox-guest-dkms Install: x11-xkb-utils:amd64 (7.7+1, automatic), libxaw7:amd64 (1.0.12-2, automatic), xfonts-utils:$ End-Date: 2014-08-21 10:03:56 Start-Date: 2014-08-21 10:18:39 Commandline: apt-get install lxde Install: desktop-base:amd64 (7.0.3, automatic), libgoa-1.0-0b:amd64 (3.12.4-1, automatic), lxmenu-d$ End-Date: 2014-08-21 10:21:52 Start-Date: 2014-08-21 10:26:40 Commandline: apt-get upgrade Upgrade: libio-socket-ssl-perl:am ifconfig on the guest: root@Peridot:~# ifconfig eth0 Link encap:Ethernet HWaddr 08:00:27:89:c9:20 og inet addr:172.31.2.102 Bcast:172.31.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe89:c920/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2281 errors:0 dropped:1 overruns:0 frame:0 TX packets:463 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:266507 (260.2 KiB) TX bytes:120554 (117.7 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240 (240.0 B) TX bytes:240 (240.0 B) The adapter in VBox is a bridged adapter directly onto my ethernet connection; as are my other 2 VMs (which work) Other SU questions I've tried: "connect: Network is unreachable" in VirtualBox VM

  Read the article

• Route web browsing through a separate iterface

  - by tkane

  I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• bond0:0 + define virtual IP

  - by yael

  in my Linux server I have the following: Linux Version - RedHat-Linux- 5.3.0.0 (this Linux server only only one LAN) more /etc/sysconfig/network-scripts/ifcfg-bond0:0 DEVICE=bond0:0 ONBOOT=yes BOOTPROTO=static IPADDR=10.10.10.12 NETMASK=255.255.255.0 ifconfig -a bond0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) bond0:0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 inet addr:10.10.10.12 Bcast:1.1.1.255 Mask:255.255.255.0 UP BROADCAST MASTER MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:0E:0C:C7:F8:92 inet addr:1.1.1.1 Bcast:1.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::20e:cff:fec7:f892/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:8600 errors:0 dropped:0 overruns:0 frame:0 TX packets:4764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:717979 (701.1 KiB) TX bytes:598620 (584.5 KiB) Memory:b8820000-b8840000 my problems: why I get HWaddr 00:00:00:00:00:00 and not the real MAC address I cant ping to other server with 10.10.10.11 from my server is it possible to define bond0:0 when I have only one LAN (eth0) other info: more /etc/modprobe.conf alias eth0 e1000e alias eth1 e1000e alias eth2 e1000e alias eth3 e1000e alias scsi_hostadapter mptbase alias scsi_hostadapter1 mptsas alias scsi_hostadapter2 ata_piix alias bond0 bonding alias bond1 bonding

  Read the article

• Centos VM serving multiple public IP: how to configure network interface?

  - by Glasnhost

  I have a Centos 5.6 VM (Vsphere client) already responding to two different public IPs on eth0 and eth0:1 and I'm trying to add eth0:2. I copied the eth0 config file and restarted the network service. I don't understand which other steps are needed... ifconfig eth0 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.10 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:163371837 errors:77 dropped:0 overruns:0 frame:0 TX packets:168210961 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1891221045 (1.7 GiB) TX bytes:855899500 (816.2 MiB) Interrupt:59 Base address:0x2000 eth0:1 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.11 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 eth0:2 Link encap:Ethernet HWaddr 00:40:46:B9:00:41 inet addr:10.1.12.12 Bcast:10.1.12.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:59 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:188976973 errors:0 dropped:0 overruns:0 frame:0 TX packets:188976973 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2015642664 (1.8 GiB) TX bytes:2015642664 (1.8 GiB) more /etc/resolv.conf nameserver 10.1.12.1 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.1.12.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.1.12.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• Atheros Wireless card shows up as two different models?

  - by geermc4

  Hi I've been fighting these wireless drivers for a few days and just recently i noticed that the model the Wireless controller appears in lspci is different sometimes. This is the data i have after installing Ubuntu Server 64 bit ~# lspci -k .... 04:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: AzureWave Device 1d89 Kernel driver in use: ath9k Kernel modules: ath9k ran some updates, restarted, all was good, all though it did say that linux-headers-server linux-image-server linux-server where beeing kept back. After that i installed ubuntu-desktop (aptitude install ubuntu-desktop --without-recommends) restarted and not only is the wireless not working anymore, but the hardware is listed as a different card ~# lspci -k .... 04:00.0 Ethernet controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) has no available drivers for it, still i tried to modprobe ath9k, they show up in lsmod as loaded, but still iw list shows nothing. this is what it looked like before the ubuntu-desktop instalation Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (14.0 dBm) * 2417 MHz [2] (15.0 dBm) * 2422 MHz [3] (15.0 dBm) * 2427 MHz [4] (15.0 dBm) * 2432 MHz [5] (15.0 dBm) * 2437 MHz [6] (15.0 dBm) * 2442 MHz [7] (15.0 dBm) * 2447 MHz [8] (15.0 dBm) * 2452 MHz [9] (15.0 dBm) * 2457 MHz [10] (15.0 dBm) * 2462 MHz [11] (15.0 dBm) * 2467 MHz [12] (15.0 dBm) (passive scanning) * 2472 MHz [13] (14.0 dBm) (passive scanning) * 2484 MHz [14] (17.0 dBm) (passive scanning) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor interface combinations are not supported Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS. What's with the hardware change? If it has 2, how can i make the AR9285 always load and disable AR5008, or, is it the same and it's just showing it different? :| Oh and I've tried this on Ubuntu 10.04 server, xubuntu 12.04, ubuntu 12.04 desktop and server. Thanks in advanced. -- Here's some more info, i have it setup in 2 hard drives, 1 works and the other one i'm using to figure it out The one that works... # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.147 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 74:2f:68:4a:26:73 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-18-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:fea00000-fea0ffff Here's where it doesn't # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.160 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network UNCLAIMED description: Ethernet controller product: AR5008 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:fea00000-fea0ffff Update I've noticed that if i blacklist the ath9k and ath9k_common modules lspci gives me the AR9285, but then I need to modprobe ath9k for it to work, does this make any sense? If so, why?

  Read the article

• Linux IPTables / routing issue

  - by Jon

  Hi all, EDIT 1/3/10 22:00 GMT - rewrote some of it after further investigation It has been a while since I looked at IPtables and I seem to be worse than before as I can not seem to get my webserver online. Below is my firewall rules on the gateway server that is running the dhcp server accessing the net. The webserver is inside my network on a static IP (192.168.0.98, default port). When I use Nmap or GRC.com I see that port 80 is open on the gateway server but when I browse to it, (via public URL. http://www.houseofhawkins.com) it always fails with a connection error, (nmap cannot connect and figure out what the web server is either). I can nmap the webserver and browse to it just fine via same IP inside my network. I believe it is my IPTable rules that are not letting it through. Internally I can route all my requests. Each machine can browse to the website and traffic works just fine. I can MSTSC / ssh to all the webservers internally and they inturn can connect to the web. IPTABLE: *EDIT - Added new firewall rules 2/3/10 * #!/bin/sh iptables="/sbin/iptables" modprobe="/sbin/modprobe" depmod="/sbin/depmod" EXTIF="eth2" INTIF="eth1" load () { $depmod -a $modprobe ip_tables $modprobe ip_conntrack $modprobe ip_conntrack_ftp $modprobe ip_conntrack_irc $modprobe iptable_nat $modprobe ip_nat_ftp echo "enable forwarding.." echo "1" > /proc/sys/net/ipv4/ip_forward echo "enable dynamic addr" echo "1" > /proc/sys/net/ipv4/ip_dynaddr # start firewall # default policies $iptables -P INPUT DROP $iptables -F INPUT $iptables -P OUTPUT DROP $iptables -F OUTPUT $iptables -P FORWARD DROP $iptables -F FORWARD $iptables -t nat -F #echo " Opening loopback interface for socket based services." $iptables -A INPUT -i lo -j ACCEPT $iptables -A OUTPUT -o lo -j ACCEPT #echo " Allow all connections OUT and only existing and related ones IN" $iptables -A INPUT -i $INTIF -j ACCEPT $iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A OUTPUT -o $EXTIF -j ACCEPT $iptables -A OUTPUT -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A FORWARD -i $EXTIF -o $INTIF -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A FORWARD -i $INTIF -o $EXTIF -j ACCEPT $iptables -A FORWARD -j LOG --log-level 7 --log-prefix "Dropped by firewall: " $iptables -A INPUT -j LOG --log-level 7 --log-prefix "Dropped by firewall: " $iptables -A OUTPUT -j LOG --log-level 7 --log-prefix "Dropped by firewall: " #echo " Enabling SNAT (MASQUERADE) functionality on $EXTIF" $iptables -t nat -A POSTROUTING -o $EXTIF -j MASQUERADE $iptables -A INPUT -i $INTIF -j ACCEPT $iptables -A OUTPUT -o $INTIF -j ACCEPT #echo " Allowing packets with ICMP data (i.e. ping)." $iptables -A INPUT -p icmp -j ACCEPT $iptables -A OUTPUT -p icmp -j ACCEPT $iptables -A INPUT -p udp -i $INTIF --dport 67 -m state --state NEW -j ACCEPT #echo " Port 137 is for NetBIOS." $iptables -A INPUT -i $INTIF -p udp --dport 137 -j ACCEPT $iptables -A OUTPUT -o $INTIF -p udp --dport 137 -j ACCEPT #echo " Opening port 53 for DNS queries." $iptables -A INPUT -p udp -i $EXTIF --sport 53 -j ACCEPT #echo " opening Apache webserver" $iptables -A PREROUTING -t nat -i $EXTIF -p tcp --dport 80 -j DNAT --to 192.168.0.96:80 $iptables -A FORWARD -p tcp -m state --state NEW -d 192.168.0.96 --dport 80 -j ACCEPT } flush () { echo "flushing rules..." $iptables -P FORWARD ACCEPT $iptables -F INPUT $iptables -P INPUT ACCEPT echo "rules flushed" } case "$1" in start|restart) flush load ;; stop) flush ;; *) echo "usage: start|stop|restart." ;; esac exit 0 route info: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 5e0412a6.bb.sky * 255.255.255.255 UH 0 0 0 eth2 192.168.0.0 * 255.255.255.0 U 0 0 0 eth1 default 5e0412a6.bb.sky 0.0.0.0 UG 100 0 0 eth2 ifconfig: eth1 Link encap:Ethernet HWaddr 00:22:b0:cf:4a:1c inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::222:b0ff:fecf:4a1c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:79023 errors:0 dropped:0 overruns:0 frame:0 TX packets:57786 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11580918 (11.5 MB) TX bytes:22872030 (22.8 MB) Interrupt:17 Base address:0x2b00 eth2 Link encap:Ethernet HWaddr 00:0c:f1:7c:45:5b inet addr:94.4.18.166 Bcast:94.4.18.166 Mask:255.255.255.255 inet6 addr: fe80::20c:f1ff:fe7c:455b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:57038 errors:0 dropped:0 overruns:0 frame:0 TX packets:34532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:21631721 (21.6 MB) TX bytes:7685444 (7.6 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1517 (1.5 KB) TX bytes:1517 (1.5 KB) EDIT OK so as requested I will try and expand on my infrastructure: I previously had it setup with a Sky broadband modem router that did the DHCP and I used its web interface to port forward the web across to the web server. The network looked something like this: I have now replaced the sky modem with a dlink modem which gives the IP to the gateway server that now does the DHCP. It looks like: The internet connection is a standard broadband connection with a dynamic IP, (use zoneedit.com to keep it updated). I have tried it on each of the webservers(one Ubuntu Apache server and one WS2008 IIS7). I think there must also be an issue with my IPTable rules as it can route to my win7 box which has the default IIS7 page and that would not display when I forwarded all port 80 to it. I would be really grateful for any and all help with this. Thanks Jon

  Read the article

• JBoss Seam project can not be run/deployed

  - by user1494328

  I created sample application in Seam framework (Seam Web Project) and JBoss Server 7.1. When I try run application, console dislays: 23:29:35,419 ERROR [org.jboss.msc.service.fail] (MSC service thread 1-3) MSC00001: Failed to start service jboss.deployment.unit."secoundProject-ds.xml".PARSE: org.jboss.msc.service.StartException in service jboss.deployment.unit."secoundProject-ds.xml".PARSE: Failed to process phase PARSE of deployment "secoundProject-ds.xml" at org.jboss.as.server.deployment.DeploymentUnitPhaseService.start(DeploymentUnitPhaseService.java:119) [jboss-as-server-7.1.1.Final.jar:7.1.1.Final] at org.jboss.msc.service.ServiceControllerImpl$StartTask.startService(ServiceControllerImpl.java:1811) [jboss-msc-1.0.2.GA.jar:1.0.2.GA] at org.jboss.msc.service.ServiceControllerImpl$StartTask.run(ServiceControllerImpl.java:1746) [jboss-msc-1.0.2.GA.jar:1.0.2.GA] at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:886) [rt.jar:1.6.0_24] at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:908) [rt.jar:1.6.0_24] at java.lang.Thread.run(Thread.java:662) [rt.jar:1.6.0_24] Caused by: org.jboss.as.server.deployment.DeploymentUnitProcessingException: IJ010061: Unexpected element: local-tx-datasource at org.jboss.as.connector.deployers.processors.DsXmlDeploymentParsingProcessor.deploy(DsXmlDeploymentParsingProcessor.java:85) at org.jboss.as.server.deployment.DeploymentUnitPhaseService.start(DeploymentUnitPhaseService.java:113) [jboss-as-server-7.1.1.Final.jar:7.1.1.Final] ... 5 more Caused by: org.jboss.jca.common.metadata.ParserException: IJ010061: Unexpected element: local-tx-datasource at org.jboss.jca.common.metadata.ds.DsParser.parseDataSources(DsParser.java:183) at org.jboss.jca.common.metadata.ds.DsParser.parse(DsParser.java:119) at org.jboss.jca.common.metadata.ds.DsParser.parse(DsParser.java:82) at org.jboss.as.connector.deployers.processors.DsXmlDeploymentParsingProcessor.deploy(DsXmlDeploymentParsingProcessor.java:80) ... 6 more 23:29:35,452 INFO [org.jboss.as.server.deployment] (MSC service thread 1-4) JBAS015877: Stopped deployment secoundProject-ds.xml in 1ms 23:29:35,455 INFO [org.jboss.as.server] (DeploymentScanner-threads - 2) JBAS015863: Replacement of deployment "secoundProject-ds.xml" by deployment "secoundProject-ds.xml" was rolled back with failure message {"JBAS014671: Failed services" => {"jboss.deployment.unit.\"secoundProject-ds.xml\".PARSE" => "org.jboss.msc.service.StartException in service jboss.deployment.unit.\"secoundProject-ds.xml\".PARSE: Failed to process phase PARSE of deployment \"secoundProject-ds.xml\""}} 23:29:35,457 INFO [org.jboss.as.server.deployment] (MSC service thread 1-1) JBAS015876: Starting deployment of "secoundProject-ds.xml" 23:29:35,920 ERROR [org.jboss.msc.service.fail] (MSC service thread 1-1) MSC00001: Failed to start service jboss.deployment.unit."secoundProject-ds.xml".PARSE: org.jboss.msc.service.StartException in service jboss.deployment.unit."secoundProject-ds.xml".PARSE: Failed to process phase PARSE of deployment "secoundProject-ds.xml" at org.jboss.as.server.deployment.DeploymentUnitPhaseService.start(DeploymentUnitPhaseService.java:119) [jboss-as-server-7.1.1.Final.jar:7.1.1.Final] at org.jboss.msc.service.ServiceControllerImpl$StartTask.startService(ServiceControllerImpl.java:1811) [jboss-msc-1.0.2.GA.jar:1.0.2.GA] at org.jboss.msc.service.ServiceControllerImpl$StartTask.run(ServiceControllerImpl.java:1746) [jboss-msc-1.0.2.GA.jar:1.0.2.GA] at java.util.concurrent.ThreadPoolExecutor$Worker.runTask(ThreadPoolExecutor.java:886) [rt.jar:1.6.0_24] at java.util.concurrent.ThreadPoolExecutor$Worker.run(ThreadPoolExecutor.java:908) [rt.jar:1.6.0_24] at java.lang.Thread.run(Thread.java:662) [rt.jar:1.6.0_24] Caused by: org.jboss.as.server.deployment.DeploymentUnitProcessingException: IJ010061: Unexpected element: local-tx-datasource at org.jboss.as.connector.deployers.processors.DsXmlDeploymentParsingProcessor.deploy(DsXmlDeploymentParsingProcessor.java:85) at org.jboss.as.server.deployment.DeploymentUnitPhaseService.start(DeploymentUnitPhaseService.java:113) [jboss-as-server-7.1.1.Final.jar:7.1.1.Final] ... 5 more Caused by: org.jboss.jca.common.metadata.ParserException: IJ010061: Unexpected element: local-tx-datasource at org.jboss.jca.common.metadata.ds.DsParser.parseDataSources(DsParser.java:183) at org.jboss.jca.common.metadata.ds.DsParser.parse(DsParser.java:119) at org.jboss.jca.common.metadata.ds.DsParser.parse(DsParser.java:82) at org.jboss.as.connector.deployers.processors.DsXmlDeploymentParsingProcessor.deploy(DsXmlDeploymentParsingProcessor.java:80) ... 6 more 23:29:35,952 INFO [org.jboss.as.controller] (DeploymentScanner-threads - 2) JBAS014774: Service status report JBAS014777: Services which failed to start: service jboss.deployment.unit."secoundProject-ds.xml".PARSE: org.jboss.msc.service.StartException in service jboss.deployment.unit."secoundProject-ds.xml".PARSE: Failed to process phase PARSE of deployment "secoundProject-ds.xml" My secoundProject-ds.xml: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE datasources PUBLIC "-//JBoss//DTD JBOSS JCA Config 1.5//EN" "http://www.jboss.org/j2ee/dtd/jboss-ds_1_5.dtd"> <datasources> <local-tx-datasource> <jndi-name>secoundProjectDatasource</jndi-name> <use-java-context>true</use-java-context> <connection-url>jdbc:mysql://localhost:3306/database</connection-url> <driver-class>com.mysql.jdbc.Driver</driver-class> <user-name>root</user-name> <password></password> </local-tx-datasource> </datasources> When I comment tags errors disappear, but application is disabled in browser (The requested resource (/secoundProject/) is not available.). What should I do to fix this problem?

  Read the article

• Crossover LAN connection between Ubuntu And Windows 7 is not working

  - by brett

  my question is closely related to: How do I connect Ubuntu 10.04 and Windows 7 with an Ethernet cable? What I am after is: Windows 7-------wireless-----\ Wifi router Ubuntu 10.04----wireless-----/ Windows 7-------wireless-----\ | cross_over_cable Wifi router | Ubuntu 10.04----wireless-----/ What I did was On Windows edit system32\drivers\etc\hosts Add the following line: 192.168.253.2 my_ubuntu_computer_name_&-wired //?not sure if this is right On Ubuntu: sudo gedit /etc/hosts Add the following line: 192.168.253.1 my_pc_computer_name&-wired //?not sure if this is right and then Ubuntu 12.04 as the host Right click on the Network Manager applet, click Edit Connections... In the Wired tab, click Auto eth0, then click Edit... In the IPv4 Settings tab, change Method: to Shared to other computers. Click Apply and enter your password when it asks you. Close everything and reboot. Plug the Ethernet cable into both computers. But, I can connect to my windows network folders from ubuntu via wifi I can't connect to my ubuntu network folders from windows via wifi(in fact this bit was working before - so my wifi connection is worse) my ubuntu Auto Ethernet seems to be on From Ubuntu eth0 Link encap:Ethernet HWaddr 00:11:2f:f3:43:8d inet addr:10.42.0.1 Bcast:10.42.0.255 Mask:255.255.255.0 inet6 addr: fe80::211:2fff:fef3:438d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:172 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:27279 (27.2 KB) Interrupt:19 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1147 errors:0 dropped:0 overruns:0 frame:0 TX packets:1147 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94380 (94.3 KB) TX bytes:94380 (94.3 KB) wlan0 Link encap:Ethernet HWaddr 00:03:c9:e9:6f:bf inet addr:10.1.1.7 Bcast:10.1.1.255 Mask:255.255.255.0 inet6 addr: fe80::203:c9ff:fee9:6fbf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13186 errors:0 dropped:0 overruns:0 frame:0 TX packets:12187 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1598882 (1.5 MB) TX bytes:1189555 (1.1 MB) From Windows: Windows IP Configuration Ethernet adapter Bluetooth Network Connection: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : Wireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : BoB Link-local IPv6 Address . . . . . : fe80::ecf7:c445:3725:b9c1%12 IPv4 Address. . . . . . . . . . . : 10.1.1.4 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.1.1.1 Tunnel adapter Local Area Connection* 15: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:1423:3ae3:f5fe:fefb Link-local IPv6 Address . . . . . : fe80::1423:3ae3:f5fe:fefb%23 Default Gateway . . . . . . . . . : :: Tunnel adapter isatap.BoB: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : BoB Tunnel adapter isatap.{D0C8EBA1-335D-4620-8570-6C36E8786D72}: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . :

  Read the article

• OpenVPN IPv6 over IPv4 tunnel

  - by user66779

  Today I installed OpenVPN 2.3rc2 on both my windows 7 client machine and centos 6 server. This new version of OpenVPN provides full compatibility for IPv6. The Problem: I am currently able to connect to the server (through the IPv4 tunnel) and ping the IPv6 address which is assigned to my client and I can also ping the tun0 interface on the server. However, I cannot browse to any IPv6 websites. My vps provider has given me this: 2607:f840:0044:0022:0000:0000:0000:0000/64 is routed to this server (2607:f840:0:3f:0:0:0:eda). This is ifconfig after setup with OpenVPN running: eth0 Link encap:Ethernet HWaddr 00:16:3E:12:77:54 inet addr:208.111.39.160 Bcast:208.111.39.255 Mask:255.255.255.0 inet6 addr: 2607:f740:0:3f::eda/64 Scope:Global inet6 addr: fe80::216:3eff:fe12:7754/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2317253 errors:0 dropped:7263 overruns:0 frame:0 TX packets:1977414 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1696120096 (1.5 GiB) TX bytes:1735352992 (1.6 GiB) Interrupt:29 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 inet6 addr: 2607:f740:44:22::1/64 Scope:Global UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:739567 errors:0 dropped:0 overruns:0 frame:0 TX packets:1218240 errors:0 dropped:1542 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:46512557 (44.3 MiB) TX bytes:1559930874 (1.4 GiB) So OpenVPN is sucessfully creating a tun0 interface and assigning clients IPv6 addresses using 2607:f840:44:22::/64. The first client to connect is getting 2607:f840:44:22::1000 and the second 2607:f840:44:22::1001, and so on... plus 1 each time. After connecting as the first client, I can ping from my windows client machine 2607:f740:44:22::1 and 2607:f740:44:22::1000. However, I have no access to IPv6 websites. I believe the problem is that the tun0 IPv6 addressees are not being forwarded to the eth0 interface. This is the firewall running on the server: #!/bin/sh # # iptables configuration script # # Flush all current rules from iptables # iptables -F iptables -t nat -F # # Allow SSH connections on tcp port 22 # iptables -A INPUT -i eth0 -p tcp --dport 22 -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22 -j ACCEPT # # Set access for localhost # iptables -A INPUT -i lo -j ACCEPT # # Accept connections on 1195 for vpn access from client # iptables -A INPUT -i eth0 -p udp --dport 1195 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p udp --sport 1195 -m state --state ESTABLISHED -j ACCEPT # # Apply forwarding for OpenVPN Tunneling # iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT iptables -t nat -A POSTROUTING -o eth0 -j SNAT --to 209.111.39.160 iptables -A FORWARD -j REJECT # # Enable forwarding # echo 1 > /proc/sys/net/ipv4/ip_forward # # Set default policies for INPUT, FORWARD and OUTPUT chains # iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT # # IPv6 # IP6TABLES=/sbin/ip6tables $IP6TABLES -F INPUT $IP6TABLES -F FORWARD $IP6TABLES -F OUTPUT echo -n "1" >/proc/sys/net/ipv6/conf/all/forwarding echo -n "1" >/proc/sys/net/ipv6/conf/all/proxy_ndp echo -n "0" >/proc/sys/net/ipv6/conf/all/autoconf echo -n "0" >/proc/sys/net/ipv6/conf/all/accept_ra $IP6TABLES -A INPUT -i eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT $IP6TABLES -A INPUT -i eth0 -p tcp --dport 22 -j ACCEPT $IP6TABLES -A INPUT -i eth0 -p icmpv6 -j ACCEPT $IP6TABLES -P INPUT ACCEPT $IP6TABLES -P FORWARD ACCEPT $IP6TABLES -P OUTPUT ACCEPT Server.conf: server-ipv6 2607:f840:44:22::/64 server 10.8.0.0 255.255.255.0 port 1195 proto udp dev tun ca ca.crt cert server.crt key server.key dh dh2048.pem ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" keepalive 10 60 tls-auth ta.key 0 cipher AES-256-CBC comp-lzo user nobody group nobody persist-key persist-tun status openvpn-status.log log-append openvpn.log verb 5 Client.conf: client dev tun nobind keepalive 10 60 hand-window 15 remote 209.111.39.160 1195 udp persist-key persist-tun ca ca.crt key client1.key cert client1.crt remote-cert-tls server tls-auth ta.key 1 comp-lzo verb 3 cipher AES-256-CBC I'm not sure where I am going wrong, it could be the firewall, or something missing from server or client.conf. This version of OpenVPN was only released yesterday, and there's little info on the internet about how to setup an IPv6 over IPv4 vpn tunnel. I've read the manual for this new version of OpenVPN (parts pertaining to IPv6) and it provides very little info too. Thanks for any help.

  Read the article

• If a cell contains a Symbol, then paste a Description into another cell

  - by Lola

  I'm working on rolling-up a series of charts. I'd like an easy way to summarize by category. The original looks like the sample below but by week for the entire year. I want to know all of the AD 1's, etc. I will need in CA (for each state) by Publication. so the end result would be CA AD 1 PUBLICATION 1 CA AD 2 PUBLICATION 1 CA AD 3 PUBLICATION 1 PUBLICATION 2 PUBLICATION 3 A B C D E 1 PUBLICATION1 CA TX NM AZ 2 AD 1 · 3 AD 2 · · · · 4 AD 3 · · · 5 PUBLICATION2 CA TX NM AZ 6 AD 1 7 AD 2 · · · 8 AD 3 · · · 9 PUBLICATION3 CA TX NM AZ 10 AD 1 11 AD 2 · · · 12 AD 3 · · · Thanks so much!

  Read the article

• Why are transactions not rolling back when using SpringJUnit4ClassRunner/MySQL/Spring/Hibernate

  - by Trevor

  I am doing unit testing and I expect that all data committed to the MySQL database will be rolled back... but this isn't the case. The data is being committed, even though my log was showing that the rollback was happening. I've been wrestling with this for a couple days so my setup has changed quite a bit, here's my current setup. LoginDAOTest.java: @RunWith(SpringJUnit4ClassRunner.class) @ContextConfiguration(locations={"file:web/WEB-INF/applicationContext-test.xml", "file:web/WEB-INF/dispatcher-servlet-test.xml"}) @TransactionConfiguration(transactionManager = "transactionManager", defaultRollback = true) public class UserServiceTest { private UserService userService; @Test public void should_return_true_when_user_is_logged_in () throws Exception { String[] usernames = {"a","b","c","d"}; for (String username : usernames) { userService.logUserIn(username); assertThat(userService.isUserLoggedIn(username), is(equalTo(true))); } } ApplicationContext-Text.xml: <?xml version="1.0" encoding="UTF-8"?> <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:p="http://www.springframework.org/schema/p" xmlns:aop="http://www.springframework.org/schema/aop" xmlns:tx="http://www.springframework.org/schema/tx" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans-2.5.xsd http://www.springframework.org/schema/aop http://www.springframework.org/schema/aop/spring-aop-2.5.xsd http://www.springframework.org/schema/tx http://www.springframework.org/schema/tx/spring-tx-2.5.xsd"> <bean id="dataSource" class="org.apache.commons.dbcp.BasicDataSource" destroy-method="close"> <property name="driverClassName" value="com.mysql.jdbc.Driver"/> <property name="url" value="jdbc:mysql://localhost:3306/test"/> <property name="username" value="root"/> <property name="password" value="Ecosim07"/> </bean> <tx:annotation-driven transaction-manager="transactionManager"/> <bean id="userService" class="Service.UserService"> <property name="userDAO" ref="userDAO"/> </bean> <bean id="userDAO" class="DAO.UserDAO"> <property name="hibernateTemplate" ref="hibernateTemplate"/> </bean> <bean id="sessionFactory" class="org.springframework.orm.hibernate3.LocalSessionFactoryBean"> <property name="dataSource" ref="dataSource"/> <property name="mappingResources"> <list> <value>/himapping/User.hbm.xml</value> <value>/himapping/setup.hbm.xml</value> <value>/himapping/UserHistory.hbm.xml</value> </list> </property> <property name="hibernateProperties"> <props> <prop key="hibernate.dialect">org.hibernate.dialect.SQLServerDialect</prop> <prop key="hibernate.show_sql">true</prop> </props> </property> </bean> <bean id="transactionManager" class="org.springframework.orm.hibernate3.HibernateTransactionManager" p:sessionFactory-ref="sessionFactory"/> <bean id="hibernateTemplate" class="org.springframework.orm.hibernate3.HibernateTemplate"> <property name="sessionFactory"> <ref bean="sessionFactory"/> </property> </bean> </beans> I have been reading about the issue, and I've already checked to ensure that the MySQL database tables are setup to use InnoDB. Also I have been able to successfully implement rolling back of transactions outside of my testing suite. So this must be some sort of incorrect setup on my part. Any help would be greatly appreciated :)

  Read the article

• Problem detaching entire object graph in GAE-J with JDO

  - by tempy

  I am trying to load the full object graph for User, which contains a collection of decks, which then contains a collection of cards, as such: User: @PersistenceCapable(detachable = "true") @Inheritance(strategy = InheritanceStrategy.SUBCLASS_TABLE) @FetchGroup(name = "decks", members = { @Persistent(name = "_Decks") }) public abstract class User { @PrimaryKey @Persistent(valueStrategy = IdGeneratorStrategy.IDENTITY) protected Key _ID; @Persistent protected String _UniqueIdentifier; @Persistent(mappedBy = "_Owner") @Element(dependent = "true") protected Set<Deck> _Decks; protected User() { } } Each Deck has a collection of Cards, as such: @PersistenceCapable(detachable = "true") @FetchGroup(name = "cards", members = { @Persistent(name = "_Cards") }) public class Deck { @PrimaryKey @Persistent(valueStrategy = IdGeneratorStrategy.IDENTITY) private Key _ID; @Persistent String _Name; @Persistent(mappedBy = "_Parent") @Element(dependent = "true") private Set<Card> _Cards = new HashSet<Card>(); @Persistent private Set<String> _Tags = new HashSet<String>(); @Persistent private User _Owner; } And finally, each card: @PersistenceCapable public class Card { @PrimaryKey @Persistent(valueStrategy = IdGeneratorStrategy.IDENTITY) private Key _ID; @Persistent private Text _Question; @Persistent private Text _Answer; @Persistent private Deck _Parent; } I am trying to retrieve and then detach the entire object graph. I can see in the debugger that it loads fine, but then when I get to detaching, I can't make anything beyond the User object load. (No Decks, no Cards). At first I tried without a transaction to simply "touch" all the fields on the attached object before detaching, but that didn't help. Then I tried adding everything to the default fetch group, but that just generated warnings about GAE not supporting joins. I tried setting the fetch plan's max fetch depth to -1, but that didn't do it. Finally, I tried using FetchGroups as you can see above, and then retrieving with the following code: PersistenceManager pm = _pmf.getPersistenceManager(); pm.setDetachAllOnCommit(true); pm.getFetchPlan().setGroup("decks"); pm.getFetchPlan().setGroup("cards"); Transaction tx = pm.currentTransaction(); Query query = null; try { tx.begin(); query = pm.newQuery(GoogleAccountsUser.class); //Subclass of User query.setFilter("_UniqueIdentifier == TheUser"); query.declareParameters("String TheUser"); List<User> results = (List<User>)query.execute(ID); //ID = Supplied parameter //TODO: Test for more than one result and throw if(results.size() == 0) { tx.commit(); return null; } else { User usr = (User)results.get(0); //usr = pm.detachCopy(usr); tx.commit(); return usr; } } finally { query.closeAll(); if (tx.isActive()) { tx.rollback(); } pm.close(); } This also doesn't work, and I'm running out of ideas...

  Read the article

• MSDTC - Communication with the underlying transaction manager has failed (Firewall open, MSDTC netwo

  - by SocialAddict

  I'm having problems with my ASP.NET web forms system. It worked on our test server but now we are putting it live one of the servers is within a DMZ and the SQL server is outside of that (on our network still though - although a different subnet) I have open up the firewall completely between these two boxes to see if that was the issue and it still gives the error message "Communication with the underlying transaction manager has failed" whenever we try and use the "TransactionScope". We can access the data for retrieval it's just transactions that break it. We have also used msdtc ping to test the connection and with the amendments on the firewall that pings successfully, but the same error occurs! How do i resolve this error? Any help would be great as we have a system to go live today. Panic :) Edit: I have created a more straightforward test page with a transaction as below and this works fine. Could a nested transaction cause this kind of error and if so why would this only cause an issue when using a live box in a dmz with a firewall? AuditRepository auditRepository = new AuditRepository(); try { using (TransactionScope scope = new TransactionScope()) { auditRepository.Add(DateTime.Now, 1, "TEST-TRANSACTIONS#1", 1); auditRepository.Save(); auditRepository.Add(DateTime.Now, 1, "TEST-TRANSACTIONS#2", 1); auditRepository.Save(); scope.Complete(); } } catch (Exception ex) { Response.Write("Test Error For Transaction: " + ex.Message + "<br />" + ex.StackTrace); } This is the ErrorStack we are getting when the problem occurs: at System.Transactions.TransactionInterop.GetOletxTransactionFromTransmitterPropigationToken(Byte[] propagationToken) at System.Transactions.TransactionStatePSPEOperation.PSPEPromote(InternalTransaction tx) at System.Transactions.TransactionStateDelegatedBase.EnterState(InternalTransaction tx) at System.Transactions.EnlistableStates.Promote(InternalTransaction tx) at System.Transactions.Transaction.Promote() at System.Transactions.TransactionInterop.ConvertToOletxTransaction(Transaction transaction) at System.Transactions.TransactionInterop.GetExportCookie(Transaction transaction, Byte[] whereabouts) at System.Data.SqlClient.SqlInternalConnection.GetTransactionCookie(Transaction transaction, Byte[] whereAbouts) at System.Data.SqlClient.SqlInternalConnection.EnlistNonNull(Transaction tx) at System.Data.SqlClient.SqlInternalConnection.Enlist(Transaction tx) at System.Data.SqlClient.SqlInternalConnectionTds.Activate(Transaction transaction) at System.Data.ProviderBase.DbConnectionInternal.ActivateConnection(Transaction transaction) at System.Data.ProviderBase.DbConnectionPool.GetConnection(DbConnection owningObject) at System.Data.ProviderBase.DbConnectionFactory.GetConnection(DbConnection owningConnection) at System.Data.ProviderBase.DbConnectionClosed.OpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory) at System.Data.SqlClient.SqlConnection.Open() at System.Data.Linq.SqlClient.SqlConnectionManager.UseConnection(IConnectionUser user) at System.Data.Linq.SqlClient.SqlProvider.get_IsSqlCe() at System.Data.Linq.SqlClient.SqlProvider.InitializeProviderMode() at System.Data.Linq.SqlClient.SqlProvider.System.Data.Linq.Provider.IProvider.Execute(Expression query) at System.Data.Linq.ChangeDirector.StandardChangeDirector.DynamicInsert(TrackedObject item) at System.Data.Linq.ChangeDirector.StandardChangeDirector.Insert(TrackedObject item) at System.Data.Linq.ChangeProcessor.SubmitChanges(ConflictMode failureMode) at System.Data.Linq.DataContext.SubmitChanges(ConflictMode failureMode) at System.Data.Linq.DataContext.SubmitChanges() at RegBook.classes.DbBase.Save() at RegBook.usercontrols.BookingProcess.confirmBookingButton_Click(Object sender, EventArgs e)

  Read the article

< Previous Page | 6 7 8 9 10 11 12 13 14 15 16 17  | Next Page >