Search Results

Search found 268 results on 11 pages for 'txqueuelen'.

Page 10/11 | < Previous Page | 6 7 8 9 10 11 | Next Page >

Problems with wired ethernet connection Ubuntu 11.10

- by Andrew Fielden

After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

Read the article
There's IP but can't reach gateway

- by icky

I have just installed ubuntu 12.04 on my new laptop, and brought it back to home, but I found the wireless network does not work. Strangely, it has the correct ip, but can't connect to the gateway. ifconfig gives ip 192.168.64.36, with broadcast 192.168.79.255 and mask 255.255.240.0, this are all correct, the gateway is at 192.168.64.1 cat /etc/resolv.conf nameserver 192.168.64.1 nameserver 127.0.0.1 which i think it's also right. but when I ping 192.168.64.1, all packages are lost. Please help me with this, I really do not know what happened to my network settings. Huckle, Thank you for your reply ifconfig wlan0 Link encap:Ethernet Hwaddr 88:f9:af:2a:ca:1b inet addr:192.168.64.36 Bcast:192.168.79.255 Mask:255.255.240.0 inet6 addr: fe80::8a9f:faff:fea2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:376 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3950 TX byetes:60288 iwconfig wlan0 IEEE 802.11bgn ESSID:"Chiono" Mode:Managed Frequency:2.417 GHz Access Point: 82:54:99:94:6D:43 Bit Rate=13.5 Mb/s Tx-Power=13 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=70/70 Signal Level=-32 dBm Rx invalid nwid:0 Rx invalid crypt:0 RX invalid frag:0 Tx excessive retries: 9 Invalid misc:10 Missed beacon:0 route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.64.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.64.0 * 255.255.240.0 U 2 0 0 0 wlan0 Thank you very much

Read the article
Internet unusably slow with Realtek Semiconductor Co., Ltd. RTL8111/8168B card

- by user42424

So I have recently installed Ubuntu 11.10 for a dual boot with wind 7. After the install I had like 300 updates, so I installed them. At first I could use the internet, although it was extremely slow. However now I cannot, sometimes it will load and others it will simply time out. When I try to download something it will either take forever or will not at all. This is a wired system. On Windows side my speeds are fine. Any help would be greatly appreciated. Also like I said I am new to Linux/Ubuntu so please be nice. One last thing, I also installed 11.10 for same dual boot on my laptop, and wireless speed is the same as on Windows? Only the wired desktop gives me the problem? Hear is some hardware info.. Hope it helps. Mobo: Gigabyte GA=880GMA- AMD / CPU: AMD Phenom (tm) IIx4 965 / 16 GB Ram / Realtek PCIe GBE Family Controller / Cisco Linksys E2000 / Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) / eth0 Link encap:Ethernet HWaddr 50:e5:49:33:64:cf inet addr:192.168.1.118 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::52e5:49ff:fe33:64cf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:76722 errors:0 dropped:76722 overruns:0 frame:76722 TX packets:49692 errors:0 dropped:65 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107956638 (107.9 MB) TX bytes:4342553 (4.3 MB) Interrupt:44 Base address:0x2000 thanks to roadmr problem solved! I powered down PC, un plugged power from pc end, waited a few (maybe 3)minutes. plugged power back in, pushed and held power button for 30 + seconds. Let go, powered on PC, and my Internet is fine! downloads and web speed blaze, just like on my Win 7 boot, maybe even faster. Problem Solved, Thanks to all!! **

Read the article
Acer aspire 5735z wireless not working after upgrade to 11.10

- by Jon

I cant get my wifi card to work at all after upgrading to 11.10 Oneiric. I'm not sure where to start to fix this. Ive tried using the additional drivers tool but this shows that no additional drivers are needed. Before my upgrade I had a drivers working for the Rt2860 chipset. Any help on this would be much appreciated.... thanks Jon jon@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1d:72:ec:76:d5 inet addr:192.168.1.134 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21d:72ff:feec:76d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:7846 errors:0 dropped:0 overruns:0 frame:0 TX packets:7213 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8046624 (8.0 MB) TX bytes:1329442 (1.3 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:91 errors:0 dropped:0 overruns:0 frame:0 TX packets:91 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34497 (34.4 KB) TX bytes:34497 (34.4 KB) Ive included by dmesg output below [ 0.428818] NET: Registered protocol family 2 [ 0.429003] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.430562] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.436614] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.437409] TCP: Hash tables configured (established 524288 bind 65536) [ 0.437412] TCP reno registered [ 0.437431] UDP hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437482] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [ 0.437678] NET: Registered protocol family 1 [ 0.437705] pci 0000:00:02.0: Boot video device [ 0.437892] PCI: CLS 64 bytes, default 64 [ 0.437916] Simple Boot Flag at 0x57 set to 0x1 [ 0.438294] audit: initializing netlink socket (disabled) [ 0.438309] type=2000 audit(1319243447.432:1): initialized [ 0.440763] Freeing initrd memory: 13416k freed [ 0.468362] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.488192] VFS: Disk quotas dquot_6.5.2 [ 0.488254] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.488888] fuse init (API version 7.16) [ 0.488985] msgmni has been set to 5890 [ 0.489381] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.489413] io scheduler noop registered [ 0.489415] io scheduler deadline registered [ 0.489460] io scheduler cfq registered (default) [ 0.489583] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.489633] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X [ 0.489699] pcieport 0000:00:1c.1: setting latency timer to 64 [ 0.489741] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X [ 0.489800] pcieport 0000:00:1c.2: setting latency timer to 64 [ 0.489841] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X [ 0.489904] pcieport 0000:00:1c.3: setting latency timer to 64 [ 0.489944] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X [ 0.490006] pcieport 0000:00:1c.4: setting latency timer to 64 [ 0.490047] pcieport 0000:00:1c.4: irq 44 for MSI/MSI-X [ 0.490126] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.490149] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.490196] intel_idle: MWAIT substates: 0x1110 [ 0.490198] intel_idle: does not run on family 6 model 15 [ 0.491240] ACPI: Deprecated procfs I/F for AC is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.493473] ACPI: AC Adapter [ADP1] (on-line) [ 0.493590] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 0.496771] ACPI: Lid Switch [LID0] [ 0.496818] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input1 [ 0.496823] ACPI: Sleep Button [SLPB] [ 0.496865] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 0.496869] ACPI: Power Button [PWRF] [ 0.496900] ACPI: acpi_idle registered with cpuidle [ 0.498719] Monitor-Mwait will be used to enter C-1 state [ 0.498753] Monitor-Mwait will be used to enter C-2 state [ 0.498761] Marking TSC unstable due to TSC halts in idle [ 0.517627] thermal LNXTHERM:00: registered as thermal_zone0 [ 0.517630] ACPI: Thermal Zone [TZS0] (67 C) [ 0.524796] thermal LNXTHERM:01: registered as thermal_zone1 [ 0.524799] ACPI: Thermal Zone [TZS1] (67 C) [ 0.524823] ACPI: Deprecated procfs I/F for battery is loaded, please retry with CONFIG_ACPI_PROCFS_POWER cleared [ 0.524852] ERST: Table is not found! [ 0.524948] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 0.680991] ACPI: Battery Slot [BAT0] (battery present) [ 0.688567] Linux agpgart interface v0.103 [ 0.688672] agpgart-intel 0000:00:00.0: Intel GM45 Chipset [ 0.688865] agpgart-intel 0000:00:00.0: detected gtt size: 2097152K total, 262144K mappable [ 0.689786] agpgart-intel 0000:00:00.0: detected 65536K stolen memory [ 0.689912] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 0.691006] brd: module loaded [ 0.691510] loop: module loaded [ 0.691967] Fixed MDIO Bus: probed [ 0.691990] PPP generic driver version 2.4.2 [ 0.692065] tun: Universal TUN/TAP device driver, 1.6 [ 0.692067] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 0.692146] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.692181] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.692206] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 0.692210] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 0.692255] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 0.692289] ehci_hcd 0000:00:1a.7: debug port 1 [ 0.696181] ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported [ 0.696202] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xf8904800 [ 0.712014] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 0.712131] hub 1-0:1.0: USB hub found [ 0.712136] hub 1-0:1.0: 6 ports detected [ 0.712230] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.712243] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 0.712247] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 0.712287] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 0.712315] ehci_hcd 0000:00:1d.7: debug port 1 [ 0.716201] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 0.716216] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf8904c00 [ 0.732014] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 0.732130] hub 2-0:1.0: USB hub found [ 0.732135] hub 2-0:1.0: 6 ports detected [ 0.732209] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.732223] uhci_hcd: USB Universal Host Controller Interface driver [ 0.732254] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.732262] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 0.732265] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 0.732298] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 0.732325] uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001820 [ 0.732441] hub 3-0:1.0: USB hub found [ 0.732445] hub 3-0:1.0: 2 ports detected [ 0.732508] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 20 (level, low) -> IRQ 20 [ 0.732514] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 0.732518] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 0.732553] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 0.732577] uhci_hcd 0000:00:1a.1: irq 20, io base 0x00001840 [ 0.732696] hub 4-0:1.0: USB hub found [ 0.732700] hub 4-0:1.0: 2 ports detected [ 0.732762] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 0.732768] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 0.732772] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 0.732805] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 0.732829] uhci_hcd 0000:00:1a.2: irq 20, io base 0x00001860 [ 0.732942] hub 5-0:1.0: USB hub found [ 0.732946] hub 5-0:1.0: 2 ports detected [ 0.733007] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 0.733014] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 0.733017] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 0.733057] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 0.733082] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001880 [ 0.733202] hub 6-0:1.0: USB hub found [ 0.733206] hub 6-0:1.0: 2 ports detected [ 0.733265] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.733273] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 0.733276] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 0.733313] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 0.733351] uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018a0 [ 0.733466] hub 7-0:1.0: USB hub found [ 0.733470] hub 7-0:1.0: 2 ports detected [ 0.733532] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.733539] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 0.733542] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 0.733578] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 0.733610] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0 [ 0.733730] hub 8-0:1.0: USB hub found [ 0.733736] hub 8-0:1.0: 2 ports detected [ 0.733843] i8042: PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 0.751594] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.751605] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.751732] mousedev: PS/2 mouse device common for all mice [ 0.752670] rtc_cmos 00:08: RTC can wake from S4 [ 0.752770] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 0.752796] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 0.752907] device-mapper: uevent: version 1.0.3 [ 0.752976] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: [email protected] [ 0.753028] cpuidle: using governor ladder [ 0.753093] cpuidle: using governor menu [ 0.753096] EFI Variables Facility v0.08 2004-May-17 [ 0.753361] TCP cubic registered [ 0.753482] NET: Registered protocol family 10 [ 0.753966] NET: Registered protocol family 17 [ 0.753992] Registering the dns_resolver key type [ 0.754113] PM: Hibernation image not present or could not be loaded. [ 0.754131] registered taskstats version 1 [ 0.771553] Magic number: 15:152:507 [ 0.771667] rtc_cmos 00:08: setting system clock to 2011-10-22 00:30:48 UTC (1319243448) [ 0.772238] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 0.772240] EDD information not available. [ 0.774165] Freeing unused kernel memory: 984k freed [ 0.774504] Write protecting the kernel read-only data: 10240k [ 0.774755] Freeing unused kernel memory: 20k freed [ 0.775093] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 [ 0.779727] Freeing unused kernel memory: 1400k freed [ 0.801946] udevd[84]: starting version 173 [ 0.880950] sky2: driver version 1.28 [ 0.881046] sky2 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.881096] sky2 0000:02:00.0: setting latency timer to 64 [ 0.881197] sky2 0000:02:00.0: Yukon-2 Extreme chip revision 2 [ 0.881871] sky2 0000:02:00.0: irq 45 for MSI/MSI-X [ 0.896273] sky2 0000:02:00.0: eth0: addr 00:1d:72:ec:76:d5 [ 0.910630] ahci 0000:00:1f.2: version 3.0 [ 0.910647] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 0.910710] ahci 0000:00:1f.2: irq 46 for MSI/MSI-X [ 0.910775] ahci: SSS flag set, parallel bus scan disabled [ 0.910812] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x33 impl SATA mode [ 0.910816] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems sxs [ 0.910821] ahci 0000:00:1f.2: setting latency timer to 64 [ 0.941773] scsi0 : ahci [ 0.941954] scsi1 : ahci [ 0.942038] scsi2 : ahci [ 0.942118] scsi3 : ahci [ 0.942196] scsi4 : ahci [ 0.942268] scsi5 : ahci [ 0.942332] ata1: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904100 irq 46 [ 0.942336] ata2: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904180 irq 46 [ 0.942339] ata3: DUMMY [ 0.942340] ata4: DUMMY [ 0.942344] ata5: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904300 irq 46 [ 0.942347] ata6: SATA max UDMA/133 abar m2048@0xf8904000 port 0xf8904380 irq 46 [ 1.028061] usb 1-5: new high speed USB device number 2 using ehci_hcd [ 1.181775] usbcore: registered new interface driver uas [ 1.260062] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1.261126] ata1.00: ATA-8: Hitachi HTS543225L9A300, FBEOC40C, max UDMA/133 [ 1.261129] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 1.262360] ata1.00: configured for UDMA/133 [ 1.262518] scsi 0:0:0:0: Direct-Access ATA Hitachi HTS54322 FBEO PQ: 0 ANSI: 5 [ 1.262716] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.262762] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) [ 1.262824] sd 0:0:0:0: [sda] Write Protect is off [ 1.262827] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.262851] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.287277] sda: sda1 sda2 sda3 [ 1.287693] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.580059] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 1.581188] ata2.00: ATAPI: HL-DT-STDVDRAM GT10N, 1.00, max UDMA/100 [ 1.582663] ata2.00: configured for UDMA/100 [ 1.584162] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GT10N 1.00 PQ: 0 ANSI: 5 [ 1.585821] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.585824] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 1.585953] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 1.586038] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 1.632061] usb 6-1: new low speed USB device number 2 using uhci_hcd [ 1.908056] ata5: SATA link down (SStatus 0 SControl 300) [ 2.228065] ata6: SATA link down (SStatus 0 SControl 300) [ 2.228955] Initializing USB Mass Storage driver... [ 2.229052] usbcore: registered new interface driver usb-storage [ 2.229054] USB Mass Storage support registered. [ 2.235827] scsi6 : usb-storage 1-5:1.0 [ 2.235987] usbcore: registered new interface driver ums-realtek [ 2.244451] input: B16_b_02 USB-PS/2 Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb6/6-1/6-1:1.0/input/input4 [ 2.244598] generic-usb 0003:046D:C025.0001: input,hidraw0: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:1d.0-1/input0 [ 2.244620] usbcore: registered new interface driver usbhid [ 2.244622] usbhid: USB HID core driver [ 3.091083] EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null) [ 3.238275] scsi 6:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS [ 3.348261] sd 6:0:0:0: Attached scsi generic sg2 type 0 [ 3.351897] sd 6:0:0:0: [sdb] Attached SCSI removable disk [ 47.138012] udevd[334]: starting version 173 [ 47.177678] lp: driver loaded but no devices found [ 47.197084] wmi: Mapper loaded [ 47.197526] acer_wmi: Acer Laptop ACPI-WMI Extras [ 47.210227] acer_wmi: Brightness must be controlled by generic video driver [ 47.566578] Disabling lock debugging due to kernel taint [ 47.584050] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 47.620666] type=1400 audit(1319239895.347:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=624 comm="apparmor_parser" [ 47.620934] type=1400 audit(1319239895.347:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=624 comm="apparmor_parser" [ 47.621108] type=1400 audit(1319239895.347:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=624 comm="apparmor_parser" [ 47.633056] [drm] Initialized drm 1.1.0 20060810 [ 47.722594] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 47.722602] i915 0000:00:02.0: setting latency timer to 64 [ 47.807152] ndiswrapper (check_nt_hdr:141): kernel is 64-bit, but Windows driver is not 64-bit;bad magic: 010B [ 47.807159] ndiswrapper (load_sys_files:206): couldn't prepare driver 'rt2860' [ 47.807930] ndiswrapper (load_wrap_driver:108): couldn't load driver rt2860; check system log for messages from 'loadndisdriver' [ 47.856250] usbcore: registered new interface driver ndiswrapper [ 47.861772] i915 0000:00:02.0: irq 47 for MSI/MSI-X [ 47.861781] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 47.861783] [drm] Driver supports precise vblank timestamp query. [ 47.861842] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem [ 47.980620] fixme: max PWM is zero. [ 48.286153] fbcon: inteldrmfb (fb0) is primary device [ 48.287033] Console: switching to colour frame buffer device 170x48 [ 48.287062] fb0: inteldrmfb frame buffer device [ 48.287064] drm: registered panic notifier [ 48.333883] acpi device:02: registered as cooling_device2 [ 48.334053] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 48.334128] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 48.334203] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 48.334644] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334652] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 48.334673] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 48.334737] HDA Intel 0000:00:1b.0: irq 48 for MSI/MSI-X [ 48.334772] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 48.356107] Adding 261116k swap on /host/ubuntu/disks/swap.disk. Priority:-1 extents:1 across:261116k [ 48.380946] hda_codec: ALC268: BIOS auto-probing. [ 48.390242] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6 [ 48.390365] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 [ 48.490870] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr [ 48.917990] ppdev: user-space parallel port driver [ 48.950729] type=1400 audit(1319239896.675:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=941 comm="apparmor_parser" [ 48.951114] type=1400 audit(1319239896.675:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=941 comm="apparmor_parser" [ 48.977706] Synaptics Touchpad, model: 1, fw: 7.2, id: 0x1c0b1, caps: 0xd04733/0xa44000/0xa0000 [ 49.048871] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8 [ 49.078713] sky2 0000:02:00.0: eth0: enabling interface [ 49.079462] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 50.762266] sky2 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control rx [ 50.762702] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 54.751478] type=1400 audit(1319239902.475:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm-guest-session-wrapper" pid=1039 comm="apparmor_parser" [ 54.755907] type=1400 audit(1319239902.479:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1040 comm="apparmor_parser" [ 54.756237] type=1400 audit(1319239902.483:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1040 comm="apparmor_parser" [ 54.756417] type=1400 audit(1319239902.483:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1040 comm="apparmor_parser" [ 54.764825] type=1400 audit(1319239902.491:11): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=1041 comm="apparmor_parser" [ 54.768365] type=1400 audit(1319239902.495:12): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=1041 comm="apparmor_parser" [ 54.770601] type=1400 audit(1319239902.495:13): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=1041 comm="apparmor_parser" [ 54.770729] type=1400 audit(1319239902.495:14): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=1038 comm="apparmor_parser" [ 54.775181] type=1400 audit(1319239902.499:15): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1043 comm="apparmor_parser" [ 54.775533] type=1400 audit(1319239902.499:16): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1043 comm="apparmor_parser" [ 54.936691] init: failsafe main process (891) killed by TERM signal [ 54.944583] init: apport pre-start process (1096) terminated with status 1 [ 55.000373] init: apport post-stop process (1160) terminated with status 1 [ 55.005291] init: gdm main process (1159) killed by TERM signal [ 59.782579] EXT4-fs (loop0): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 [ 60.992021] eth0: no IPv6 routers present [ 61.936072] device eth0 entered promiscuous mode [ 62.053949] Bluetooth: Core ver 2.16 [ 62.054005] NET: Registered protocol family 31 [ 62.054007] Bluetooth: HCI device and connection manager initialized [ 62.054010] Bluetooth: HCI socket layer initialized [ 62.054012] Bluetooth: L2CAP socket layer initialized [ 62.054993] Bluetooth: SCO socket layer initialized [ 62.058750] Bluetooth: RFCOMM TTY layer initialized [ 62.058758] Bluetooth: RFCOMM socket layer initialized [ 62.058760] Bluetooth: RFCOMM ver 1.11 [ 62.059428] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 62.059432] Bluetooth: BNEP filters: protocol multicast [ 62.460389] init: plymouth-stop pre-start process (1662) terminated with status 1 '

Read the article
openvpn: after changing to server mode, client does not create TUN device

- by lurscher

i had a previously working configuration with the config files used in a previous question However, i've changed this now to the following configuration using server mode, everything on the logs seem fine, however the client doesn't create any tun interface, so i don't have anything to connect to, presumably, i need to add or push some route commands, but i don't have any idea at this point what i need to do. I am posting all my relevant configuration files server.conf: dev tun server 10.8.117.0 255.255.255.0 ifconfig-pool-persist ipp.txt tls-server dh /home/lurscher/keys/dh1024.pem ca /home/lurscher/keys/ca.crt cert /home/lurscher/keys/vpnCh8TestServer.crt key /home/lurscher/keys/vpnCh8TestServer.key status openvpn-status.log log openvpn.log comp-lzo verb 3 and client.conf: dev tun remote my.server.com tls-client ca /home/chuckq/keys/ca.crt cert /home/chuckq/keys/vpnCh8TestClient.crt key /home/chuckq/keys/vpnCh8TestClient.key ns-cert-type server ; port 1194 ; user nobody ; group nogroup status openvpn-status.log log openvpn.log comp-lzo verb 3 the server ifconfig shows a tun device: tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.117.1 P-t-P:10.8.117.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) However the client ifconfig does not show any tun interface! $ ifconfig tun0 tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 POINTOPOINT NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) the client log says: Tue May 17 23:27:09 2011 OpenVPN 2.1.0 i686-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 12 2010 Tue May 17 23:27:09 2011 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue May 17 23:27:09 2011 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Tue May 17 23:27:09 2011 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted> Tue May 17 23:27:09 2011 LZO compression initialized Tue May 17 23:27:09 2011 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue May 17 23:27:09 2011 TUN/TAP device tun0 opened Tue May 17 23:27:09 2011 TUN/TAP TX queue length set to 100 Tue May 17 23:27:09 2011 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue May 17 23:27:09 2011 Local Options hash (VER=V4): '41690919' Tue May 17 23:27:09 2011 Expected Remote Options hash (VER=V4): '530fdded' Tue May 17 23:27:09 2011 Socket Buffers: R=[114688->131072] S=[114688->131072] Tue May 17 23:27:09 2011 UDPv4 link local (bound): [undef] Tue May 17 23:27:09 2011 UDPv4 link remote: [AF_INET]192.168.0.101:1194 Tue May 17 23:27:09 2011 TLS: Initial packet from [AF_INET]192.168.0.101:1194, sid=8e8bdc33 f4275407 Tue May 17 23:27:09 2011 VERIFY OK: depth=1, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=Ubuntu_CA/name=lurscher/[email protected] Tue May 17 23:27:09 2011 VERIFY OK: nsCertType=SERVER Tue May 17 23:27:09 2011 VERIFY OK: depth=0, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=vpnCh8TestServer/name=lurscher/[email protected] Tue May 17 23:27:09 2011 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:09 2011 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:09 2011 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:09 2011 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:09 2011 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Tue May 17 23:27:09 2011 [vpnCh8TestServer] Peer Connection Initiated with [AF_INET]192.168.0.101:1194 Tue May 17 23:27:10 2011 Initialization Sequence Completed the client status log: OpenVPN STATISTICS Updated,Tue May 17 23:30:09 2011 TUN/TAP read bytes,0 TUN/TAP write bytes,0 TCP/UDP read bytes,5604 TCP/UDP write bytes,4244 Auth read bytes,0 pre-compress bytes,0 post-compress bytes,0 pre-decompress bytes,0 post-decompress bytes,0 END and the server log says: Tue May 17 23:18:25 2011 OpenVPN 2.1.0 x86_64-pc-linux-gnu [SSL] [LZO2] [EPOLL] [PKCS11] [MH] [PF_INET6] [eurephia] built on Jul 12 2010 Tue May 17 23:18:25 2011 IMPORTANT: OpenVPN's default port number is now 1194, based on an official port number assignment by IANA. OpenVPN 2.0-beta16 and earlier used 5000 as the default port. Tue May 17 23:18:25 2011 WARNING: --keepalive option is missing from server config Tue May 17 23:18:25 2011 NOTE: your local LAN uses the extremely common subnet address 192.168.0.x or 192.168.1.x. Be aware that this might create routing conflicts if you connect to the VPN server from public locations such as internet cafes that use the same subnet. Tue May 17 23:18:25 2011 NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Tue May 17 23:18:25 2011 Diffie-Hellman initialized with 1024 bit key Tue May 17 23:18:25 2011 /usr/bin/openssl-vulnkey -q -b 1024 -m <modulus omitted> Tue May 17 23:18:25 2011 TLS-Auth MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue May 17 23:18:25 2011 ROUTE default_gateway=192.168.0.1 Tue May 17 23:18:25 2011 TUN/TAP device tun0 opened Tue May 17 23:18:25 2011 TUN/TAP TX queue length set to 100 Tue May 17 23:18:25 2011 /sbin/ifconfig tun0 10.8.117.1 pointopoint 10.8.117.2 mtu 1500 Tue May 17 23:18:25 2011 /sbin/route add -net 10.8.117.0 netmask 255.255.255.0 gw 10.8.117.2 Tue May 17 23:18:25 2011 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue May 17 23:18:25 2011 Socket Buffers: R=[126976->131072] S=[126976->131072] Tue May 17 23:18:25 2011 UDPv4 link local (bound): [undef] Tue May 17 23:18:25 2011 UDPv4 link remote: [undef] Tue May 17 23:18:25 2011 MULTI: multi_init called, r=256 v=256 Tue May 17 23:18:25 2011 IFCONFIG POOL: base=10.8.117.4 size=62 Tue May 17 23:18:25 2011 IFCONFIG POOL LIST Tue May 17 23:18:25 2011 vpnCh8TestClient,10.8.117.4 Tue May 17 23:18:25 2011 Initialization Sequence Completed Tue May 17 23:27:22 2011 MULTI: multi_create_instance called Tue May 17 23:27:22 2011 192.168.0.104:1194 Re-using SSL/TLS context Tue May 17 23:27:22 2011 192.168.0.104:1194 LZO compression initialized Tue May 17 23:27:22 2011 192.168.0.104:1194 Control Channel MTU parms [ L:1542 D:138 EF:38 EB:0 ET:0 EL:0 ] Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel MTU parms [ L:1542 D:1450 EF:42 EB:135 ET:0 EL:0 AF:3/1 ] Tue May 17 23:27:22 2011 192.168.0.104:1194 Local Options hash (VER=V4): '530fdded' Tue May 17 23:27:22 2011 192.168.0.104:1194 Expected Remote Options hash (VER=V4): '41690919' Tue May 17 23:27:22 2011 192.168.0.104:1194 TLS: Initial packet from [AF_INET]192.168.0.104:1194, sid=8972b565 79323f68 Tue May 17 23:27:22 2011 192.168.0.104:1194 VERIFY OK: depth=1, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=Ubuntu_CA/name=lurscher/[email protected] Tue May 17 23:27:22 2011 192.168.0.104:1194 VERIFY OK: depth=0, /C=CA/ST=Out/L=There/O=Ubuntu/OU=Home/CN=Ubuntu_CA/name=lurscher/[email protected] Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Tue May 17 23:27:22 2011 192.168.0.104:1194 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Tue May 17 23:27:22 2011 192.168.0.104:1194 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Tue May 17 23:27:22 2011 192.168.0.104:1194 [vpnCh8TestClient] Peer Connection Initiated with [AF_INET]192.168.0.104:1194 Tue May 17 23:27:22 2011 vpnCh8TestClient/192.168.0.104:1194 MULTI: Learn: 10.8.117.6 -> vpnCh8TestClient/192.168.0.104:1194 Tue May 17 23:27:22 2011 vpnCh8TestClient/192.168.0.104:1194 MULTI: primary virtual IP for vpnCh8TestClient/192.168.0.104:1194: 10.8.117.6 finally, the server status log: OpenVPN CLIENT LIST Updated,Tue May 17 23:36:25 2011 Common Name,Real Address,Bytes Received,Bytes Sent,Connected Since vpnCh8TestClient,192.168.0.104:1194,4244,5604,Tue May 17 23:27:22 2011 ROUTING TABLE Virtual Address,Common Name,Real Address,Last Ref 10.8.117.6,vpnCh8TestClient,192.168.0.104:1194,Tue May 17 23:27:22 2011 GLOBAL STATS Max bcast/mcast queue length,0 END

Read the article
Why does my MySQL remote-connection fail (VLAN)?

- by Johannes Nielsen

ubuntu-community! Again I have a problem with my special friend MySQL :D I have got two servers - a database-server and a web-server - who are connected via VLAN. Now I want the web-server to have remote access to the database-server's MySQL. So I created the user user in mysql.user. user's Host is xxx.yyy.zzz.9 which is the internal IP-address of the web-server. xxx.yyy.zzz.0 is the network. I also created user with Host % . As long as I use MySQL on the database-server logging in as user, everything works fine. But trying to log in as user from xxx.yyy.zzz.9 using mysql -h xxx.yyy.zzz.8 -u user -p (where xxx.yyy.zzz.8 is the database-server's internal IP), I get ERROR 2003 (HY000): Can't connect to MySQL server on 'xxx.yyy.zzz.8' (110) So I tried to activate Bind-Address in the my.cnf file. Well, if I use xxx.yyy.zzz.8, nothing changes. But if I try xxx.yyy.zzz.9 and try to restart MySQL, I get mysql stop/waiting start: Job failed to start I checked the log files and found - nothing. The database-server's MySQL doesn't even register, that the web-server tries to connect remotely. My idea is, that maybe I didn't configure the VLAN properley, even though I asked someone who actually knows such stuff and he told me, I did everything right. What I wrote into /etc/networking/interfaces is: #The VLAN auto eth1 iface eth1 inet static address xxx.yyy.zzz..8 netmask 255.255.255.0 network xxx.yyy.zzz.0 broadcast xxx.yyy.zzz.255 mtu 1500 ifconfig returns eth1 Link encap:Ethernet HWaddr xxxxxxxxxxxxxx inet addr:xxx.yyy.zzz.8 Bcast:xxx.yyy.zzz.255 Mask:255.255.255.0 inet6 addr: xxxxxxxxxxxxxxx/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:241146 errors:0 dropped:0 overruns:0 frame:0 TX packets:9765 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:17825995 (17.8 MB) TX bytes:566602 (566.6 KB) Memory:fb900000-fb920000 for the eth1, what is, what I configured. (This is for the database-server, the web-server looks similar). ethtool eth1 returns: Settings for eth1: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000003 (3) drv probe Link detected: yes (This is for the database-server, the web-server looks similar). Actually I think, everything is right, but it still doesn't work. Is there someone with an idea? EDIT: I commented ou Bind-Address in my.cnf after it didn't work.

Read the article
Hostapd - WLAN as AP

- by BBK

I'm trying to start hostapd but without success. I'm using Headless Ubuntu 11.10 oneiric 3.0.0-16-server x86_64. WLAN driver is rt2800usb and my wireless nic card TP-Link TL-WN727N supports AP mode as shows below: us0# ifconfig wlan0 wlan0 Link encap:Ethernet HWaddr 00:27:19:be:cd:b6 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) us0# lsusb Bus 003 Device 003: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter us0# lshw -C network *-network:3 description: Wireless interface physical id: 4 bus info: usb@3:2 logical name: wlan0 serial: 00:27:19:be:cd:b6 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.0.0-16-server firmware=0.29 link=no multicast=yes wireless=IEEE 802.11bgn us0# hostapd /etc/hostapd/hostapd.conf Configuration file: /etc/hostapd/hostapd.conf Could not read interface wlan0 # The int flags: No such device nl80211 driver initialization failed. ELOOP: remaining socket: sock=4 eloop_data=0xd3e4a0 user_data=0xd3ecc0 handler=0x433880 ELOOP: remaining socket: sock=6 eloop_data=0xd411f0 user_data=(nil) handler=0x43cc10 us0# cat /etc/hostapd/hostapd.conf ssid=Home interface=wlan0 # The interface name of the card #driver=rt2800usb driver=nl80211 macaddr_acl=0 ieee80211n=1 channel=1 hw_mode=g auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_passphrase=88888888 wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP us0# iw list Wiphy phy0 Band 1: Capabilities: 0x172 HT20/HT40 Static SM Power Save RX Greenfield RX HT20 SGI RX HT40 SGI RX STBC 1-stream Max AMSDU length: 7935 bytes No DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 2 usec (0x04) HT RX MCS rate indexes supported: 0-7, 32 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (20.0 dBm) (passive scanning, no IBSS) * 2472 MHz [13] (20.0 dBm) (passive scanning, no IBSS) * 2484 MHz [14] (20.0 dBm) (passive scanning, no IBSS) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * Unknown command (68) * Unknown command (55) * Unknown command (57) * Unknown command (59) * Unknown command (67) * set_wiphy_netns * Unknown command (65) * Unknown command (66) * connect * disconnect The question is: Why the hostapd not starting?

Read the article
Why am I getting a "network is unreachable" error on Ubuntu Server?

- by jason328

I'm a completely new to Ubuntu server and am having a hard time connecting the server to the internet. I first ran ping -n 8.8.8.8 connect:Network is unreachable Then I ran ifconfig Link encap:Local Loopback inet addr:127.0.0.1 Mask 255.0.0.0 inet6 addr: ::1/28Scope:host UP LOOPBACK RUNNING MTU:16436 RX packets:192 errors:0 dropped:0 overruns:0 frame:0 TX packets:192 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:15360 (15.2KB) TX bytes:15360 (15.3KB) Here is ouput for sudo lspci -n 00:00.0 0600: 8086:2580 (rev 04) 00:02.0 0300: 8086:2582 (rev 04) 00:1d.0 0c03: 8086:2658 (rev 03) 00:1d.1 0c03: 8086:2659 (rev 03) 00:1d.0 0c03: 8086:265a (rev 03) 00:1d.0 0c03: 8086:265b (rev 03) 00:1d.0 0c03: 8086:265c (rev 03) 00:1e.0 0604: 8086:244e (rev d3) 00:1e.0 0401: 8086:266e (rev 03) 00:1f.0 0601: 8086:2640 (rev 03) 00:1f.0 0101: 8086:2651 (rev 03) 00:1f.0 0c05: 8086:266a (rev 03) 00:0b.0 0200: 8086:1654 (rev 03) lshw-c network returns WARNING: you should run this program as super-user. *-network DISABLED description:Ethernet interface product: NetXtreme BCM5705_2 Gigabit Ethernet vender: Broadcom Corporation physical id:b bus info:pci@0000:0a:0b.0 logical name: eth0 capabilities: bus_master_cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion= 3.121 firmware=5705-v3.18 latency=32 mingnt=64 multicast=yes port=twister pair lsmod code returned this Module Size Used By e100 37213 0 dm_crypt 23125 1 ppdev 17113 0 psmouse 87603 0 snd_intel8x0 38570 0 snd_ac97_codec 134826 1 snd_intel8x0 ac97_bus 12730 1 snd_ac97_codec snd_pcm 97188 2 snd_intel8x0, snd_ac97_codec serio_raw 13211 0 snd_timer 29990 1 snd_pcm snd 78855 4 snd_intel8x0, snd_ac97_codec, snd_pcm,snd_timer soundcore 15091 1 snd snd_page_alloc 18529 2 snd_intel8x0, snd_pcm ext2 73795 1 parport_pc 32866 1 mac_hid 13253 0 lp 17799 0 parport 46562 3 ppdev, parport_pc,lp usbhid 47199 0 hid 99559 1 usbhid tg3 152032 0 i915 468651 1 floppy 70365 0 drm_kms_helper 46978 1 i915 drm 242038 2 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 Again there is more but it's giving info on the driver itself. I know it works, I've used it. I assume then that my network got disabled when I installed Ubuntu Server. How do I enable it? I checked and the internet cable is connected to the D-link router. I have also used this same computer for internet access when I had Ubuntu Desktop installed so internet does work.

Read the article
Bind9 configured to start at boot, has to be started manually

- by antik

I've configured bind9 on my system and it works great when it runs. It's currently configured to be run at runlevel 2 by setting: $ sudo update-rc.d bind9 enable 2 This appears to have done its work: $ tree -f /etc/rc?.d | grep -e ".*bind9$" |-- /etc/rc0.d/K85bind9 -> ../init.d/bind9 |-- /etc/rc2.d/S15bind9 -> ../init.d/bind9 |-- /etc/rc3.d/S15bind9 -> ../init.d/bind9 |-- /etc/rc4.d/S15bind9 -> ../init.d/bind9 |-- /etc/rc5.d/S15bind9 -> ../init.d/bind9 |-- /etc/rc6.d/K85bind9 -> ../init.d/bind9 Booting the system, I believe I am at runlevel 2: $ runlevel N 2 Given the above configuration, when the system is rebooted, bind does not come up. Only on occasion, for some reason, can I resolve hostnames immediately after startup. Far more often than not however, I cannot. I can interrogate the service's status: $ sudo /etc/init.d/bind9 status * could not access PID file for bind9 When the service doesn't start, I can start it successfully via a terminal by issuing $ sudo /etc/init.d/bind9 start And it works great from then on. Loopback configuration: $ ifconfig lo lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1872 errors:0 dropped:0 overruns:0 frame:0 TX packets:1872 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:220205 (220.2 KB) TX bytes:220205 (220.2 KB) Do I have my startup misconfigured? (I'm used to Gentoo so Ubuntu's model is still a little new to me) I'm not seeing any log indication of a failed attempt to start at boot in syslog. Is there someplace else I should be looking? What else should I look into to get bind working at startup?

Read the article
can't find port 22 traffic under VirtualBox

- by telliott99

I'm trying to learn to use tcpdump. I thought I'd eavesdrop on my ssh login. The setup is a bit unusual, I have OS X Lion running VirtualBox, with Ubuntu running in the VM. I have ssh enabled and can login from OS X normally: > ssh -p 22 10.0.1.2 -l telliott Welcome to Ubuntu 11.10 (GNU/Linux 3.0.0-17-generic i686) * Documentation: https://help.ubuntu.com/ 0 packages can be updated. 0 updates are security updates. Last login: Sat Mar 31 19:54:36 2012 from toms-mac-mini.local telliott@U32:~$ logout Connection to 10.0.1.2 closed. > I have not obfuscated the ssh port on Ubuntu. From OS X, stroke gives what I expect: > ./stroke 10.0.1.2 22 22 Port Scanning host: 10.0.1.2 Open TCP Port: 22 ssh So from OS X I do: > sudo tcpdump -i en1 -v port 22 Password: tcpdump: listening on en1, link-type EN10MB (Ethernet), capture size 65535 bytes Then I login from OS X to Ubuntu using ssh, but I see nothing with tcpdump. Here is ifconfig from Ubuntu: telliott@U32:~$ ifconfig eth1 Link encap:Ethernet HWaddr 08:00:27:d7:ba:0e inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fed7:ba0e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:799 errors:0 dropped:0 overruns:0 frame:0 TX packets:465 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:96863 (96.8 KB) TX bytes:68638 (68.6 KB) Where are the packets I was hoping to see? Thanks for any help.

Read the article
Secondary IP (eth0:0) acts like main server IP

- by George Tasioulis

I have a CentOS server, configured with 4 consecutive IPs: eth0 5.x.x.251 eth0:0 5.x.x.252 eth0:1 5.x.x.253 eth0:2 5.x.x.254 The problem is that all traffic goes out to the internet with eth0:0 (5.x.x.252) as the source IP, instead of eth0. # curl ifconfig.me 5.x.x.252 How can I fix this, so that all traffic goes out via eth0, ie my main IP? PS: My server is VPS running on a Xen dom0, the latter being configured in routed mode networking. Thanks in advance! Server configuration # ifconfig eth0 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.251 Bcast:5.x.x.255 Mask:255.255.255.255 inet6 addr: fe80::x:x:x:x/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14675569 errors:0 dropped:0 overruns:0 frame:0 TX packets:9463227 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4122016502 (3.8 GiB) TX bytes:25959110751 (24.1 GiB) Interrupt:23 eth0:0 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.252 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 eth0:1 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.253 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 eth0:2 Link encap:Ethernet HWaddr 00:x:x:x:x:AE inet addr:5.x.x.254 Bcast:5.x.x.255 Mask:255.255.255.224 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:23 # cat /etc/hosts 127.0.0.1 localhost.localdomain localhost 5.x.x.251 [fqdn] [hostname] # cat ifcfg-eth0 DEVICE=eth0 BOOTPROTO=static ONBOOT=yes IPADDR=5.x.x.251 NETMASK=255.255.255.224 SCOPE="peer 5.x.y.82" # cat ifcfg-eth0:0 DEVICE=eth0:0 BOOTPROTO=static ONBOOT=yes IPADDR=5.x.x.252 NETMASK=255.255.255.224 # cat route-eth0 ADDRESS0=0.0.0.0 NETMASK0=0.0.0.0 GATEWAY0=5.x.y.82 # netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 5.x.y.82 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 5.x.x.224 0.0.0.0 255.255.255.224 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 5.x.y.82 0.0.0.0 UG 0 0 0 eth0

Read the article
Centos 6.2 Fresh 'Basic Server' install networking issues

- by RWC

I've had a /29 provisioned on a network port for a server and am trying to at least configure the machine so I can ssh into it. It's Centos 6.2 x64 with the Basic Server install. Currently not able to ping gateway or any address for that matter. For reference: Default Interface: em2 Network ID: 66.*.*.0/29 Gateway: 66.*.*.1 Broadcast: 66.*.*.7 Please see my following configs: /etc/sysconfig/network-scripts/ifcfg-em2 DEVICE=em2 NM_CONTROLLED=yes ONBOOT=yes HWADDR=Not Important TYPE=Ethernet BOOTPROTO=none IPADDR=66.*.*.2 PREFIX=29 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System em2" NETMASK=255.255.255.248 USERCTL=no $: route -n Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 0.0.0.0 255.255.255.248 U 0 0 0 em2 169.254.0.0 0.0.0.0 255.255.0.0 U 0 1003 0 em2 0.0.0.0 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: route Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 * 255.255.255.248 U 0 0 0 em2 link-local * 255.255.0.0 U 0 1003 0 em2 default 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: cat /etc/sysconfig/network NETWORKING=yes HOSTNAME=excalibur.domain.com GATEWAY=66.*.*.1 Keep in mind that I cannot even currently ping the gateway which is quite confusing for me. My /etc/hosts are configured correctly with the *.2 address. I'm not concerned with getting all of the addresses on the /29 up and running yet, just one so I can at least ssh in. Thanks! Edit: Adding in ifconfig. $: ifconfig em2 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:XX inet addr:66.*.*.2 Bcat:66.*.*.7 Mask:255.255.255.248 inet6 addr: UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5536 errors:0 dropped:0 overruns:0 frame:0 TX packets:10 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2599469 (2.4 MiB) TX bytes: 748 (748.0 b) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:34 errors:0 etc etc

Read the article
NFS high CPU usage

- by user269836

Hello, I have a very strange issue. I have next server: Intel(R) Xeon(TM) MP CPU 3.16GHz cat /proc/cpuinfo | grep proce | wc -l 8 free -m total used free shared buffers cached Mem: 28203 27606 596 0 10789 9714 -/+ buffers/cache: 7103 21100 Swap: 24695 0 24695 RAID card *-storage description: RAID bus controller product: MegaRAID vendor: LSI Logic / Symbios Logic physical id: 7 bus info: pci@0000:13:07.0 logical name: scsi2 version: 01 width: 32 bits clock: 66MHz capabilities: storage pm bus_master cap_list rom configuration: driver=megaraid latency=32 resources: irq:134 memory:d8ff0000-d8ffffff(prefetchable) memory:df600000-df60ffff(prefetchable) HDD: 10x148Gb SCSI U320 15k - RAID5 /dev/sdb1 807G 674G 93G 88% /storage /dev/sdb1 /storage ext4 defaults,usrjquota=aquota.user,grpjquota=aquota.group,jqfmt=vfsv0,noatime,nodiratime,noacl,errors=remount-ro 0 1 network cards ethtool -i eth0 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ethtool -i eth1 driver: tg3 version: 3.116 firmware-version: 5704-v3.36, ASFIPMIc v2.36 bus-info: 0000:10:02.0 ifconfig bond0 Link encap:Ethernet HWaddr 00:0f:1f:ff:d6:4d inet addr:192.168.15.71 Bcast:192.168.15.255 Mask:255.255.255.0 inet6 addr: fe80::20f:1fff:feff:d64d/64 Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:1062818202 errors:0 dropped:3918 overruns:0 frame:0 TX packets:1041317321 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10000 RX bytes:258867684559 (241.0 GiB) TX bytes:396569192650 (369.3 GiB) this server running only nfs-kernel-server uname -a Linux nas2-backup 2.6.32-5-amd64 #1 SMP Sun Sep 23 10:07:46 UTC 2012 x86_64 GNU/Linux Debian 6. What do I have, once per day or two, LA goes up, it can be reached around LA: 40 but if I do: nfs-kernel-server restart. Every thing is OK. But on the next day or a little bit later, LA goes up again. Servers are connected to d-link dgs 1016d with 24 GBits ports. I have tried everything to find out what the problem is. Why it's happening, but still I can not resolve this issue. Any ideas on what is happening here?

Read the article
NTOP gives warnings on startup

- by FR6

I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

Read the article
virtualisation with kvm: export services from guest to the host

- by ascobol

Hello, I would like to export some services from the guest os to the host os, via kvm, and by the same way learn some things about networking. I have tried the following commands: In the host (kubuntu 10.4): $ sudo tunctl -u ascobol Set 'tap0' persistent and owned by uid 2401 $ sudo ifconfig tap0 192.168.2.1 netmask 255.255.255.0 broadcast 192.168.2.255 The ifconfig command returns: $ /sbin/ifconfig tap0 Link encap:Ethernet HWaddr 3e:4e:e3:cc:bc:92 inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::3c4e:e3ff:fecc:bc92/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:17 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 Then I run the virtual machine (ubuntu server 10.4): $ sudo kvm -hda ubuntuserver104.qcow2 -net nic -net tap,name=tap0,script=no (I'm using sudo because without it fails with the following message:) warning: could not configure /dev/net/tun: no virtual network emulation With sudo the virtual machine boots, I just get this message: pci_add_option_rom: failed to find romfile "pxe-rtl8139.bin" In the virtual machine: $ ifconfig eth0 192.168.2.2 netmask 255.255.255.0 broadcast 192.168.2.255 Now if I run: $ ssh 192.168.2.2 I just get a No route to host What is wrong with this setup ? Thanks !

Read the article
Add IPv6 support to DirectAdmin server

- by George Boot

I just set up an new DirectAdmin, and I want to prepare it for IPv6 use. My ISP have gave me an range of IPv6 addresses that I can use. Lets say that address is 2a01:7c8:**:1f::. My neworkadapter user DHCP to resolves its IP-addresses. When i type ifoncig eth0 I get the following result: eth0 Link encap:Ethernet HWaddr 52:**:**:**:ce:f3 inet addr:37.**.**.44 Bcast:37.**.**.255 Mask:255.255.255.0 inet6 addr: 2a01:7c8:****:1f::/64 Scope:Global inet6 addr: fe80::5054:ff:fe87:cef3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38941 errors:0 dropped:0 overruns:0 frame:0 TX packets:29439 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3779534 (3.6 MiB) TX bytes:5089379 (4.8 MiB) As you can see, I have an IPv6 address set, but I can't ping6 an IPv6 host. I get the error: connect: Network is unreachable. I decided that I needed an gateway, so I tryed to add one: ip -6 route add default via 2a01:7c8:****::1 dev eth0 (2a01:7c8:**::1 is the gateway of my ISP). But it trows an error: RTNETLINK answers: No route to host. Does somebody know what to do, and how to solve this issue? Thanks a lot!

Read the article
Intel NIC X540-T1 non-functional in Ubuntu Server 12.04

- by Jeff Carr

I have installed three Intel X540-T1's in servers running Ubuntu Server 12.04, but all are non-functional, no link lights, no packets sent or received, and no connection on ip4 or ip6 whether set up as dhcp or static. Also, dmesg doesn't detect cable connection or disconnection. I updated the default ixgbe driver to Intel's latest version (3.11.33) with no change. The ethernet controller is being reported as X540-AT2 (which might be a problem that I can't figure out how to fix), but the subsystem is X540-T1 so I believe that might be intended. Does anyone have any experience with this that could assist? ifconfig eth2 eth2 Link encap:Ethernet HWaddr a0:36:9f:14:5f:ea inet addr:192.168.101.1 Bcast:192.168.101.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1<br> RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ethtool -i eth2 driver: ixgbe version: 3.11.33 firmware-version: 0x8000037c bus-info: 0000:08:00.0 supports-statistics: yes supports-test: yes supports-eeprom-access: yes supports-register-dump: yes lspci -vvnns 08:00.0 08:00.0 Ethernet controller [0200]: Intel Corporation Ethernet Controller 10 Gigabit X540-AT2 [8086:1528] (rev 01) Subsystem: Intel Corporation Ethernet Converged Network Adapter X540-T1 [8086:0002] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at e8000000 (64-bit, prefetchable) [size=2M] Region 4: Memory at e8200000 (64-bit, prefetchable) [size=16K] [virtual] Expansion ROM at e8280000 [disabled] [size=512K] Capabilities: <access denied> Kernel driver in use: ixgbe Kernel modules: ixgbe

Read the article
How does Windows 7 DNS client work?

- by Mark Allison

I am using a local DHCP and DNS server on my home network on a linux machine. It is running CentOS 6.3 with dnsmasq 2.48. It's all working fine except for local DNS lookups for Windows machines only. I have a mix of Ubuntu, CentOS and Windows machines on the network, some virtual, some physical. I have a machine called boron and the domain is called localdomain If I ping boron from any linux machine, I get [root@lithium lists]# ping -c3 boron PING boron.localdomain (10.0.0.5) 56(84) bytes of data. 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=1 ttl=64 time=0.740 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=2 ttl=64 time=0.478 ms 64 bytes from boron.localdomain (10.0.0.5): icmp_seq=3 ttl=64 time=0.458 ms --- boron.localdomain ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2000ms rtt min/avg/max/mdev = 0.458/0.558/0.740/0.131 ms If I do it from my Windows 7 machine, I get: Ping request could not find host boron. Please check the name and try again. If I try ping boron.localdomain I get: Pinging boron.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=16ms TTL=57 Reply from 67.215.65.132: bytes=32 time=188ms TTL=57 Reply from 67.215.65.132: bytes=32 time=15ms TTL=57 Reply from 67.215.65.132: bytes=32 time=14ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 14ms, Maximum = 188ms, Average = 58ms which is clearly wrong. Why is it going out to the internet? Why can't my windows machine resolve the boron hostname to a FQDN? My Windows machines and linux machines get their network config from DHCP. UPDATE If I do ipconfig /all in Windows, it looks as I would expect: Windows IP Configuration Host Name . . . . . . . . . . . . : lanthanum Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No DNS Suffix Search List. . . . . . : .localdomain Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : .localdomain Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller Physical Address. . . . . . . . . : 50-E5-49-38-FC-A2 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 10.0.0.57(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Lease Obtained. . . . . . . . . . : 23 August 2012 13:58:45 Lease Expires . . . . . . . . . . : 24 August 2012 07:58:48 Default Gateway . . . . . . . . . : 10.0.0.6 DHCP Server . . . . . . . . . . . : 10.0.0.6 DNS Servers . . . . . . . . . . . : 10.0.0.6 208.67.222.222 208.67.220.220 NetBIOS over Tcpip. . . . . . . . : Enabled When I do an nslookup I get: Server: carbon.localdomain Address: 10.0.0.6 *** carbon.localdomain can't find boron: Unspecified error However if I do ifconfig -a in Linux I get: [root@nitrogen ~]# ifconfig -a eth0 Link encap:Ethernet HWaddr 00:0C:29:AF:EC:2A inet addr:10.0.0.7 Bcast:10.0.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:187687 errors:0 dropped:0 overruns:0 frame:0 TX packets:5857 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:23910700 (22.8 MiB) TX bytes:712964 (696.2 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:329894 errors:0 dropped:0 overruns:0 frame:0 TX packets:329894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:67153143 (64.0 MiB) TX bytes:67153143 (64.0 MiB) and nslookup: [root@nitrogen ~]# nslookup boron Server: 10.0.0.6 Address: 10.0.0.6#53 Name: boron Address: 10.0.0.5 Both machines are on the same network using the same DHCP server. UPDATE 2 I thought the issue was resolved but I am getting intermittent DNS resolving issues but only on my Windows 7 machine. All my linux boxes are fine. This is what happens when I ping and nslookup from Windows to a Windows 2008 Server: C:\Users\mark>nslookup magnesium Server: carbon.localdomain Address: 10.0.0.6 Name: magnesium.localdomain Address: 10.0.0.12 C:\Users\mark>ping magnesium Pinging magnesium.localdomain [67.215.65.132] with 32 bytes of data: Reply from 67.215.65.132: bytes=32 time=267ms TTL=57 Reply from 67.215.65.132: bytes=32 time=162ms TTL=57 Reply from 67.215.65.132: bytes=32 time=510ms TTL=57 Reply from 67.215.65.132: bytes=32 time=146ms TTL=57 Ping statistics for 67.215.65.132: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 146ms, Maximum = 510ms, Average = 271ms And from Linux: [root@beryllium ~]# ping -c4 magnesium PING magnesium.localdomain (10.0.0.12) 56(84) bytes of data. 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=1 ttl=128 time=0.176 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=2 ttl=128 time=0.634 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=3 ttl=128 time=0.685 ms 64 bytes from magnesium.localdomain (10.0.0.12): icmp_seq=4 ttl=128 time=0.263 ms --- magnesium.localdomain ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3002ms rtt min/avg/max/mdev = 0.176/0.439/0.685/0.223 ms [root@beryllium ~]# nslookup magnesium Server: 10.0.0.6 Address: 10.0.0.6#53 Name: magnesium.localdomain Address: 10.0.0.12 UPDATE 3 I stopped the Windows DNS client on my Windows 7 machine with net stop dnscache and it is now working fine. It would be nice to get DNS working with the DNS client on, but I might be OK without it, what do you think?

Read the article
Ubuntu second static IP, ifconfig, /etc/network/interfaces

- by Schmoove

I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

Read the article
Debian/Ubuntu - No network connection

- by leviathanus

I have a very weird situation on my Ubuntu 12.04 LTS Server. I can not access (ping) my gateway, although I believe my config is ok - I attach the outputs. Any hints where to look? (I changed the beginning of the IP to something different, just obfuscation) ping 5.9.10.129 PING 5.9.10.129 (5.9.10.129) 56(84) bytes of data. From 5.9.10.129 (5.9.10.129) icmp_seq=2 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=3 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=4 Destination Host Unreachable uname -r 3.2.0-29-generic ifconfig eth0 eth0 Link encap:Ethernet HWaddr 3c:97:0e:0e:54:d7 inet addr:5.9.10.142 Bcast:5.9.10.159 Mask:255.255.255.224 inet6 addr: fe80::8e70:5aff:feda:c4ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1216 errors:0 dropped:0 overruns:0 frame:0 TX packets:490 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107470 (107.4 KB) TX bytes:34344 (34.3 KB) Interrupt:17 Memory:d2500000-d2520000 ip route default via 5.9.10.129 dev eth0 metric 100 5.9.10.128/27 via 5.9.10.129 dev eth0 5.9.10.128/27 dev eth0 proto kernel scope link src 5.9.10.142 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 5.9.10.129 0.0.0.0 UG 1000 0 0 eth0 5.9.10.128 5.9.10.129 255.255.255.224 UG 0 0 0 eth0 5.9.10.128 0.0.0.0 255.255.255.224 U 0 0 0 eth0 iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination UPD: Eric, this is how routing information looks on a working server: 0.0.0.0 78.47.198.49 0.0.0.0 UG 100 0 0 eth0 78.47.198.48 78.47.198.49 255.255.255.240 UG 0 0 0 eth0 78.47.198.48 0.0.0.0 255.255.255.240 U 0 0 0 eth0 As I understand it, Hetzner tries to ensure security by this, so I can not take over an IP by changing my MAC. But this is another server, which has another netmask (255.255.255.240) UPD2: BatchyX, on the working server: 78.47.198.49 dev eth0 src 78.47.198.60 cache on the broken: 5.9.10.129 dev eth0 src 5.9.10.142 cache

Read the article
Routing subnet over GRE tunnel

- by eMgz

Hi, Im trying to configure a GRE over IPSec connection between two subnets. The IPSec tunnel is opened and now I want to add a GRE tunnel over it: ip tunnel add GRE01 mode gre remote 10.244.0.1 local 10.244.245.32 ttl 255 ip link set GRE01 up ip addr add 10.244.248.126 dev GRE01 ip route add 10.244.248.125 dev GRE01 Now I have an interface GRE01 (ifconfig): GRE10 Link encap:UNSPEC HWaddr <h_addr> inet addr:10.244.248.126 P-t-P:10.244.248.126 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MTU:1476 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And the following routes (ip route list): 10.244.248.125 dev GRE10 scope link <pub_subnet> dev eth0 proto kernel scope link src <pub_ip> default via <pub_gw> dev eth0 metric 100 As a last step, I need now to route my subnet over the tunnel: ip route add 10.245.1.224/28 10.244.248.125 However, I am getting the error Error: either "to" is duplicate, or "10.244.248.125" is a garbage. So, what I didn't understand is why I can't route my subnet over the tunnel, once the only route I have there says that it should route the tunnel IP over the GRE01 interface. Any hint? Thanks.

Read the article
Debian can't connect to internet using LAN

- by tampe125

I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

Read the article
Debian can't connect to internet using LAN

- by tampe125

I have a headless Raspberry Pi using Debian Wheezy. I have a wifi dongle and if I connect my Raspberry using it, everything works fine: I can connect to the Internet, I can ping, I can update. However, if I get down my wifi and set up the lan interface, I lost my internet connection. I still can connect to it locally, using my laptop, but the connection doesn't exit (ie ping is not working). Some useful info: cat /etc/network/interfaces auto lo auto eth0 iface eth0 inet static address 192.168.0.105 netmask 255.255.255.0 gateway 192.168.0.1 ping www.google.com (nothing request timed out) ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:a2:b5:20 inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1130 errors:0 dropped:0 overruns:0 frame:0 TX packets:1116 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:97223 (94.9 KiB) TX bytes:146140 (142.7 KiB) ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. ^C --- 192.168.0.1 ping statistics --- 19 packets transmitted, 0 received, 100% packet loss, time 18007ms cat /etc/resolv.conf nameserver 8.8.8.8 netstat -r Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface default 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 well, I think that's all... Any ideas?

Read the article
NTOP gives warnings on startup

- by FR6

I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

Read the article
Connect linux server to VPN server via PPTP

- by wowpatrick

I'm trying to connect a Linux (Ubuntu 10.04 LST) server to a VPN server via the PPTP client to an VPN server. I configured the PPTP client as said in the documentation. The connection is correctly added as an interface, but somehow the connection dose not work. ping -I ppp0 google.com dose not return anything and traceroute -i ppp0 only shows the first hop, and then displays nothing. Any ideas of what is going wrong? Incorrect routing configuration? ifconfig output for the configured interface: ppp0 Link encap:Point-to-Point Protocol inet addr:xx.x.xxx.xxx P-t-P:10.0.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1496 Metric:1 RX packets:415 errors:0 dropped:0 overruns:0 frame:0 TX packets:468 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:31428 (31.4 KB) TX bytes:32394 (32.3 KB) route output Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.x.x.1 * 255.255.255.255 UH 0 0 0 ppp0 xx.xxx.xxx.xx sp.ip 255.255.255.255 UGH 0 0 0 eth1 192.168.3.0 * 255.255.255.0 U 0 0 0 eth2 192.168.2.0 * 255.255.255.0 U 0 0 0 eth1 default sp.ip 0.0.0.0 UG 100 0 0 eth1

Read the article

< Previous Page | 6 7 8 9 10 11 | Next Page >