Search Results

Search found 2962 results on 119 pages for 'cisco vpn'.

Page 100/119 | < Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >

• SBS 2008 DNS issues in BPA

  - by evesirim

  I'm gettng constant Critical Issue events in the Small Business Server Best Practices Analyser & resulting SBS Console reports that begin "The DNS client is not configured to point only to the internal IP address of the server.". When I check the DNS Manager, there are two separate IPs listed, one ***.***.***.2 and the other ***.***.***.28. I have checked online after an ipconfig /all and have found the reason for this to be that the second IP is created by DHCP for RAS & VPN purposes. It seems to cause no conflicts of any detrimental result apart from constantly sending me error messages and alerted reports. Does anyone know of a way that I can change settings somewhere so that Windows accepts this second IP, or at least stops alerting me of its prescence? Perhaps a registry hack of some kind...? Many thanks in advance

  Read the article

• Windows Server 2012 Essentials - Trying to setup "Anywhere Access" but the "Computer Access" list for users is blank

  - by tetranz

  I have a new installation of Windows Server 2012 Essentials and I'm trying to setup "Anywhere Access" for both VPN and remote desktop. The basic setup is all working. Shared folders is working but remote desktop has no computers available. On the server, if I edit a user with the Essentials Dashboard and go to "Computer access", the list is empty. The desktop computers have been joined to the domain. I can see them in AD under "Computers". I think our mistake was that we didn't use the connector tool to join the domain. We moved from a previous domain and went to Computer / Properties, changed the domain and started with a new profile. Is there something I can do now to make these desktops available for remote desktop? I can access a desktop directly no problem by going directly to it with the RDP client on port 3389. I do that from the outside world through an SSH tunnel.

  Read the article

• XDMCP works for Solaris, not for RHEL

  - by joshxdr

  I have some old RHEL4 servers that until recently I was able to connect to remotely with Exceed (remote desktop using XDMCP) from my windowsXP PC. My PC is connected to our network by wired LAN. Recently it seems something has changed in our network. I can still connect to all the old Solaris and HPUX servers with Exceed, but for some reason I can no longer connect to the RHEL4 servers. I assume this is some kind of "security" feature turned on in our network. Does anyone know what this might be, and how I can tell IT to re-enable it? Update: A colleague has found that he can connect (very slowly) to these RHEL4 boxes with XDMCP if he is using our VPN from home, but when he is in the office using wired LAN he cannot connect to them. So it seems that there is some kind of firewall or ???, part of our wired LAN network, that is blocking XDMCP traffic from RHEL4.

  Read the article

• Corporate IM with video that actually works, suggestions?

  - by Erik P. Skaalerud

  Hi. Does anyone here have a suggestion for a cross-platform IM solution wich will work with voip/video on both Windows (XP and 7) and Mac OS X from 10.4 and upwards? Right now were in a kind of mixed enviroment, with some Mac users using iChat server since they need video support (conference across several offices over VPN), but it wont't work on windows clients. The rest of us are happily using Openfire+Spark, but there's no VoIP or video avaible from what i've found, unless you want to add in several 3rd party software (like red5 and asterisk). Requirements: As said before; must work on both Windows and Mac Internal server (no Skype etc) File transfer between platforms SSO (Single Sign-On) via Active Directory authentication Some sort of screen sharing would be a plus, like switching over to a screen capture (powerpoint, software training etc) We can afford to buy software if that's needed to get this working without any hiccups across platforms. Pre-thanks to anyone who gives suggestions.

  Read the article

• What does a red icon in XP's "Unlock Computer" dialog mean?

  - by wikiti

  A user was working from home and had a colleague turn on her computer so she could remote desktop to it. All worked fine, but when she came into the office and used her computer for a while then locked it the computer icon had a red screen, instead of blue. Like in the following mockup: Mockup of red computer screen. It didn't cause any problems and it went away when she rebooted, but I was intrigued to find out whether there was something that caused it or if it was just a windows oddity. I believe she just closed the remote desktop session (without really logging off) from home and then disconnected from the VPN before coming to the office. Any ideas?

  Read the article

• How can I use dynamic routing with openvpn tunnels?

  - by pQd

  i'm thinking about using dynamic routing [ OSPF or RIP ] via OpenVPN tunnels. right now i have few offices connected in full mesh, but this is not scalable solution as we add more locations. i would like to avoid situation when plenty of internal traffic is affected if one of two vpn termination points that i plan to use is down. do you have similar configuration working in production? if so - what routing daemon did you use - quagga? something else? did you encounter any problems? thanks!

  Read the article

• Encrypt LAN and wifi traffic on small private network

  - by Grimlockz

  I need some advice about encrypt all traffic on a small private network running wi-fi and LAN traffic on 192.168.0.x network. The network would comprise of client laptops connecting to the wi-fi router (192.168.0.254) via ethernet connection or wireless. The main purpose of the server is for the client laptops to talk to two servers on different IP's (192.168.0.200 and 192.168.0.201) on ports 80 and 433. My main concern is having packet sniffers and what not getting access to the data. The only ways I see at the moment is to have VPN running on the network or use IPSec policy's to do this. Any other ways guys?

  Read the article

• firefox: getting access to the list of tabs/windows to restore on startup

  - by robb

  Sometimes ffox fails to restore the previously open tabs/windows. This might be happening when some of the urls to be opened are no longer reachable (e.g. behind a vpn) or after the underlying OS (Windows) has been forcibly restarted (e.g. to complete an automated patch installation). Anyway, after restarting, can this list of urls be recovered somehow? Say for example, I was daft enough to have clicked on "start new session". Can I still get access to the old list of open urls? There is the browser history of course, but it contains a lot of stuff - the urls that were open when ffox last exited are not obvious. It would be neat if they were marked in some way - tagged for example. .robb

  Read the article

• SBS 2011 on different subnet than domain computers

  - by Ravi

  The setup is as follows: SBS 2011 in datacentre on subnet A Domain PCs at another location on subnet B There is a site-to-site VPN. The domain PCs have joined the domain and have the SBS as their primary DNS server. The domain PCs can ping the DC but the problem is that the DC cannot ping any of the remote subnet (subnet B) SBS --Switch -- Router A ------------------- Router B -- Switch -- Domain PCs What is strange is that router A can ping any host on the subnet B. Another host on Subnet A can also ping any host on subnet B. It's only the DC which cannot ping anything to that specific remote subnet B. I did a tracert from the SBS to router B. The packet reaches Router A from the SBS but then it fails. Am I missing some specific settings that needs to be done when SBS is on a different subnet than its member pcs ?

  Read the article

• clam anti-virus is slowing down my server performance significantly

  - by Scarface

  Hey guys, I just installed clam av http://sourceforge.net/projects/php-clamav/ for scanning file uploads on my linux VPN running php. The problem is that for some reason just initiating the extension in the php ini file slows down my entire network. Regular requests such as changing pages that should take less than 1 second take 5. Has anyone ever experienced this before or have a good virus scanning alternative for scanning file uploads? extension=clamav.so [clamav] clamav.dbpath="/usr/share/clamav" clamav.keeptmp=20 clamav.maxreclevel=16 clamav.maxfiles=10000 clamav.maxfilesize=26214400 clamav.maxscansize=104857600 clamav.keeptmp=0

  Read the article

• rpd over https using a linux client

  - by Nils

  My employer switched from vpn and rdp to using what our admin calls "rdp over https". Since that switch I find myself unable to connect to the "new" rdp server. I think the progress is as follows: A rdp gateway-server is connected via tls the requested sever (different from the gateway-server) is then connected through the tls connection. In windows mstsc-settings the server name is the "internal network name" of the machine I wish to connect. And on the last tab (in German it is called "leistung" - could be activity) I go to the "connection from everywhere" settings and set the gateway-server under gateway-server. Now: Is there any way to use this scenario under linux (apart from a virtual machine running Windows)? I am interested in free ideas (e.g. is it possible to create a tls tunnel and connect through that using freerdp/rdesktop?) non-free ideas. As long as they work I'll worry about the costs later. Free ideas would be better :-)

  Read the article

• dd-wrt Bonjour/ netbios etc on two subnets

  - by user72182

  Hi I was wondering if any clever people out there could help me. I have a network setup with two different subnets 192.168.1.0 and 192.168.0.0 one router is connected to a VPN (via OpenVPN) the other is not. Both routers have static routes to each other and a device on one can communicate to another without issues when using IP addresses. My problem is I want to use services like Bonjour, Netbios and Apple Talk across the two networks, which currently does not work. A laptop connected on one subnet will not see a laptop connected on another. Is there anyway that you can connect the two networks together so these sort of local service will work??? I guess I have to forward the boardcast packets but I have no idea how to do this. Thanks for any help...

  Read the article

• Why does WebDAV fail from inside home network

  - by Claus

  On my OSX server there is a folder that is configured in the Server App to be accessible via WebDAV. This folder is used to sync OmniFocus. On my router, I have set up a dynamic dns. When I am outside my home network (physically away or when connected via a vpn), I can connect and sync fine via: https://<server name from dyndns>/<username>/<path to WebDAV folder> However, when I am in my home network, the connection to WebDAV does not work (other connections, AFP, f.ex, do work). What could be some reasons why I can't connect to WebDAV from within my home network? What log files could give hints and where are they stored? I am running OSX server 10.9.3. and server.app. Thanks for your help.

  Read the article

• router propogation usng OSPF

  - by liv2hak

  I am using Juniper J-series routers to emulate a small telco and VPN customer.I need to use OSPF so that the path to each internal subnet is propogated to all PE nodes.The network topology is given below. To achieve this I am planning to run the following commands in UOW-TAU and UOW-HAM. set protocols ospf area 0.0.0.0 interface ge-0/0/0 set protocols ospf area 0.0.0.0 interface lo0.0 Do I need to do any additional configuration in TAU-PE1 and HAM-PE1 routers for it to receive the OSPF paths.? I am a beginner at the routing.Any help is appreciated.

  Read the article

• Streaming media from linux server - low footprint is crucial

  - by Mike Haye

  I recently pre-ordered the Raspberry Pi. http://www.raspberrypi.org/faqs For those of you who don't know it, it's a machine with 256 mb ram and a 700 MHz processor for $35. I plan to run linux on an SD card on this machine and have it act as both a htpc, VPN and media server. In regard to the media server part, I need to find some linux software that has a small footprint, but allows me to stream media to other devices connected to the internet (preferably without having to install any additional software on the client machines) Also, I would love if the video could be compressed, so the data usage wouldn't be so big for the client machine (e.g. when I'm using my data plan on my smartphone ;) ) Thanks in advance for any answers :) Mike.

  Read the article

• AFP / Apple Filling Protocol aka Netatalk access over Internet

  - by PJJ

  I got a simple cloud server and thought it would be nice to have mac native afp Volumes accesss. Installed Netatalk and this seems to work pretty nice. No sensitive data or something but I don't like to wake up someday and have my www docs rm-rfed by some kid h4x0r. Q1: Is afp encrypted? Q2: How can I make it (semi)secure? Q3: Does VPN makes sense for this? Q4: What would you do to get afp working over net? Opening any service meant for Lan only is a basic flaw, i know - but me be ignorant about it. According to Apple Dev only the authentication is encrypted or am I mssing something?

  Read the article

• How can I connect to a CIFS/SMB share on a non-default port?

  - by fsckin

  I'm trying to get a contractor connected to a CIFS share (port 445). He's not a big shop (so no go on using VPN). His ISP blocks outgoing connections on port 445. I've been doing some rsync to ftp madness as a workaround to have the share available to him, but it's getting out of control -- we're syncing nearly 40GB a day to an external ftp site and it's going to be much easier just to have him connect and only grab the stuff he needs. So... I can have the CIFS share open to the internet (filtered to allow access to his IP only) on port 446. How the heck can he connect to that? I looked through "net use" and didn't see anything about using another port.

  Read the article

• unusual webpage access problem

  - by user28163

  This is one of the weirdest problems I've ever seen and I'm out of ideas. I cannot access a couple of websites from my home pc (for 3-4 days now), or at least they go really really slow ~700b/s I can access these same websites fine from my laptop from same IP address. - The websites originate from different countries and are huge popular sites. - I have tried both my PC's network cards. - I have reformatted my PC. - I have reset my router to factory settings. - I have created virtual computers on my PC, and from inside those I cannot access the webpages. - I have flushed my dns. - I tried specifying my dns server addresses to 8.8.8.8 and 8.8.4.4. I can only access the webpages using my PC, if I first connect to an outside VPN. Again, these sites work fine on the 2 other pcs in this house (same ISP and internet connection). help plz :)

  Read the article

• Is there a convenient way to manually copy the Log Shipping *.trn files from one SQL 2008 server to

  - by Rick

  We have a remote SQL 2008 server (ServerB) that needs to keep a warm (15 minute interval is OK) copy of production data (ServerA). ServerA is also SQL 2008. Log Shipping looks like it will do the job. We can only get to the destination ServerB with remote desktop. Is there a way to set this up when we can't get to both servers from one Management Studio? We want to be able to temporarily (until a VPN is setup between our network and the ServerB network) manually export a small .trn file, copy it via remote desktop to ServerB and then manually import those transactions from the .trn file. My supervisor says he saw a post saying this is possible. We were just trying to avoid doing a full database backup and copying that every time. Thanks in advance for any suggestions on this.

  Read the article

• IP Tunneling for Spotify? [closed]

  - by everwicked

  I was in the UK and enjoyed Spotify relentlessly. Now I've moved back to Greece and I can't even pay for the darn thing. So my idea was this- I have a server in France and it has a fail-over IP in the UK. So I installed a proxy server on it and made it listen to the UK IP. So far so good. Then, I played Spotify for a while through the proxy server just fine, and it thought I was in the UK. But now... it gives me an error message that I'm in another country than the one on my profile (UK). I don't really understand why - maybe they also geolocate the IP address of the client, not just the proxy server? Either way, I'm kinda stuck - is there a way to tunnel Spotify's network traffic through my server transparently? Maybe a VPN or something similar? Thanks

  Read the article

• How can I set up OpenVPN to accept more than 60 connections?

  - by Robin

  Greetings! We're using OpenVPN and today hit an unexpected connection limit of 60 - even though max-clients is set to the source code default 1024. Server log: Tue Dec 21 13:49:41 2010 MULTI: new incoming connection would exceed maximum number of clients (60) We're slowly adding new clients to the VPN and expect to hit 200 some time next year, if we can get it working. We're running the server on a Win2003 R2. OpenVPN 2.0.9 Server config as follows: local 192.168.10.211 port 1195 proto tcp dev tun dev-node OpenVPN_Vision ca vision_ca.crt cert vision_server.crt key vision_server.key # This file should be kept secret dh vision_dh1024.pem server 192.168.211.0 255.255.255.0 ifconfig-pool-persist vision_ipp.txt ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 ;client-to-client keepalive 10 120 comp-lzo ;max-clients 100 # Default in source code is 1024 persist-key persist-tun status openvpn-status-vision.log log vision.log verb 3 I would greatly appreciate any help or input on this one. Thanks! Best regards, Robin

  Read the article

• How can I restrict SSH access when the source IP is dynamic

  - by Supratik

  Hi I want to protect SSH access to our live web server from all IP's except our office static IP. There are some employees who connects to this live server from their dynamic IP's. So, it is not always possible for me to change in the iptables rule in live server whenever the dynamic IP of the employee changes. I tried to put them in office VPN and allowed only SSH access from office IP but the office connection is slow in compared to our employee's private internet connection, moreover it adds an extra overhead to our office network. Is there any way I can solve this problem ?

  Read the article

• How come I can't ping my home computer?

  - by bikefixxer

  I'm trying to set up a vpn into my home computer in order to access files from wherever. I have the home computer set up with a no-ip dynamic dns program so I can always connect, and have also tried using the actual ip address. However, when I try to connect or even ping from anywhere outside of my house I can't get through. I've tried putting that particular computer in the dmz, turned off the computers firewall and anti-virus, and I still don't get anything. I have comcast as my home internet provider. I have also tried from two different locations. Are there any other solutions I can try or is comcast the issue? I used to be able to do this when I ran a small web server at home for fun but now nothing works. Thanks in advance for any suggestions!

  Read the article

• Windows Server 2008: Terminal Services / VDI

  - by JohnyD

  I have a Dell R710 with 72GB of memory running Hyper-V. Within Hyper-V I have a Windows 2008 (32-bit) VM running Terminal Services. How do I allocate memory so that any user who connects to this Terminal Server (from their thin-client) is allocated 2GB (or whatever amount I choose) of memory? Currently I have provisioned the TS with 2GB of memory but it seems that this is shared among all that connect. Please let me know if there is further information I can provide. Thank you. Update 1: What I'm looking to accomplish with this server is setting up a VDI to allow users to connect from thin-clients from within our network. They will also have to connect from outside our network via VPN which is already in place. Am I able to set this up using Windows Server 2008 (not R2) because I have a 16-bit application which needs to be supported. Unfortunately it's not a candidate as a Remote App.

  Read the article

• How do I keep multiple copies of Outlook in sync when using RPC over HTTP?

  - by Don

  I use Outlook 2007 at work with our Exchange 2003 server. I just setup my home system with Outlook 2007 so that I could use the RPC over HTTP to access Exchange without having to use a VPN. It works fine. I can get mail, send mail, etc. What it doesn't seem to be doing is staying in sync. For example, I read a few messages at home, moved them into different folders from the Inbox, etc. That all seemed fine. When I login to my work machine and look at the copy of Outlook there, the mail is still unread and nothing has been moved. Am I missing something simple here? I would have to assume that my home machine should be telling Exchange where these messages belong and that they've been read. Both machines are running Windows 7, if that matters. Ideas?

  Read the article

< Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >