Search Results

Search found 3018 results on 121 pages for 'plug in'.

Page 100/121 | < Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >

  • Output current with Teensy++ 2.0 (arduino-based hardware)

    - by omtinez
    I am working on a project with a Teensy++ 2.0 for testing, eventually the goal is to use a Teensy 2.0 (info on both available here) and mount it onto a robot R/C car along with a Raspberry Pi. I have been able to use and test one of the very cheap distance sensors that use ultrasound, which requires very little current. I was trying to power a motor, I don't know exactly what kind of motor but I assume a very low-power one which is what comes with the R/C car cheapo, but nothing is happening. When I plug the motor to GROUND and +5V it runs fine, but when I use GROUND and one of the GPIO pins then nothing happens with the motor. The same GPIO pins were tested to successfully power and run the ultrasound sensor, so the board is fine. My suspicion is that the GPIO pins don't output enough current to power the motor, but my knowledge of electronics is rather scarce (I am a computer scientist, not an electrical engineer). So please forgive me if I am asking something obvious or plain stupid, but does the board not have enough power to power the motor? If so, I could try to use a second power supply that would go straight into the motor and use the GPIO as a gate to turn that power on and off; would such thing work? Is there a better design that could be used?

    Read the article

  • Compiz and Desktop Effects on Netbook with External Monitor

    - by Nerdfest
    I have an Acer Aspire One AO150 and am having trouble plugging in an external monitor under Ubuntu 9.10. There were no problems under 9.04. If I plug in an external monitor once the machine is already up, then bring up the 'display' application to activate it, it basically hangs. There are no problem under these circumstances if I have desktop effects turned off. I've seen a few mentions of this problem on the Ubuntu forums, but never a solid solution. Any ideas? A few more details after a question below. The machine does not respond to its keyboard commands to switch to an external monitor, nor does it respond to Ctrl-Alt-F1, etc to switch out of X. The pointer is visible on the monitors (at the edge of each) and is frozen as a 'busy' cursor, but with no animation. The kernel does respond to SysReq commands (REISUB). In the latest attempt I had the external monitor active earlier, then removed it and activated desktop effects. Upon plugging in the eternal monitor then bringing up the display application, it hangs.

    Read the article

  • Network outage caused by SMC8013WG Cable Modem/Router ?

    - by mkocubinski
    At work, we have a basic Class C Network. The gateway/router is a SMC8013WG (stock comcast commercial cable modem), and simple unmanaged switch (HP Pro Curve 1400 24G). The SMC8013WG is our default gateway as well as DHCP server. Periodically, I'd say almost every other day.. the entire network will just stop responding. I won't be able to ping/see the gateway, any computers on our local network, or anything on the internet. The only way to fix this is to unplug the Comcast cable modem, wait, and plug back in. This unfailingly fixes the problem. But this doesn't make much sense to me.. shouldn't the network still be fine locally, since everything is plugged into the switch anyway? Why would resetting the router fix this? Can anyone suggest anything to check to in order to narrow this problem down? Just to be clear.. here is the basic topology: { Internet } -- (12.345.67.89) Comcast Cable Modem (192.168.1.1) -- Switch -- 192.168.1.2-254 P.S. Our IT guy is in about 3 hours a day every other week or so, so.. we're kind of on our own most of the time.

    Read the article

  • USB Hub vs. Dockinstation USB vs. Laptop USB

    - by Will
    I recently had thougts about my current setup in my office, especially about the UBS ports distribution. Here's my setup: I have a Lenovo T410 docked to a Lenovo Dockingstation Series 3, that providey me with 6 USB ports, which I use all (3 ext. drives, mouse, keyboard, USB Hub of monitor). The USB hub on my ext. monitor (most probably powered by the ext. monitor's power supply) provides me with 2 USB ports, where I use one for my webcam and another for USB sticks. On my T410 itself I have 4 USB slots, that are usually not used, as don't want to mess with USB plugs when undocking my laptop, now and then I plug my printer on one of these, just because I don't have any UBS ports left. Now I'm wondering how fast each of these slots are: I assume that all the 6 USB ports from the dockinstation somehow go through the docking connector on the bottom of my laptop. Does this connector has such a big bandwidth for all these 6 USB ports to perform like if they were dedicated ports as the 4 ones on my laptop? Also how is generally the performance of USB hubs (like the one on my ext. monitor?)?

    Read the article

  • How many bootable partitions are possible to have on one hard drive?

    - by draiden
    This may not be the correct place to post this; if that's the case, just let me know and point me in the right direction please! I'm thinking of building a box that needs to be lightweight and portable, and would need to be able to boot multiple installations of windows. I am needing to have multiple installations so that I can, for example, plug the box in to the network at one location, boot in to that location's partition, and have full access to everything I would normally need to do on a computer that has already been set up on that network. Then, when I go to the next client, I would be able to do the same thing, with the new location's partition, and have all of those network settings, drive mappings, etc., available there. Obviously I'd need to go through and set them all up on the different locations/networks, I'm not expecting it to magically know where I am and what I'm doing. It would be like I'm carrying around a computer that is configured for each place I need to go in one little box, instead of having to have multiple computers or having to reconfigure all the settings and such every time I go to another client. Or is there an easier way to do this that I haven't learned of?

    Read the article

  • Hard Reset USB in Ubuntu 10.04

    - by Cory
    I have a USB device (a modem) that is really finicky. Sometimes it works fine, but other times it refuses to connect. The only solution I have found to fix it once it gets into a bad state is to physically unplug the device and plug it back in. However, I don't always have physical access to the machine it is plugged in on, so I'm looking for a way to do this through the command line. This post suggests running: $ sudo modprobe -w -r usb_storage; sudo modprobe usb_storage However I get an "unknown option -w" output. This slightly modified command: $ sudo modprobe -r usb_storage Fails with the message FATAL: Module usb_storage is in use. If I try to kill -9 the processes marked [usb-storage] before running they refuse to die (I think because they are deeply tied to the kernel). Anyone know of a way to do this? NOTE: I cross-posted this on serverfault as I didn't know which was more appropriate. I will delete and/or link whichever one is answered first.

    Read the article

  • Need recommendation: which USB card (PCMCIA) works with external hard drive?

    - by Carl
    I have an HT-Link Cardbus/PCMCIA USB 2.0 2-port card (NEC / 32-bit). My external hard drive w/USB adapter won't work with it, and it will work plugged directly into a USB port on a different laptop. (My USB ports got fried.) I got the card off E-Bay. My MP3 player works plugged into that card. The drivers for the card say "Known limitations: High Speed Isochronus, USB Composite Devices." (No other details provided.) I don't know if the hard drive adapter is "isochronous" or "composite." I've read there are problems with too little power being supplied to the drive. The cable to the drive has two USB plugs on one end, and it doesn't make any difference if I plug both of them into the Cardbus card. What card should I get? I see many different brands on E-Bay. I need one that supplies sufficient power for an external hard drive, and doesn't have any "known limitations" in the way.

    Read the article

  • USB Diskdrive cannot be formatted nor accessed

    - by Dmolish
    So I have just recently bought and 8GB USB stick(Kingston DT 100 G2) on which I had installed Linux. However I needed to reinstall said Linux so I formatted the stick to "default" settings which includes FAT32 filesystem. Later when the install process kept getting errors, I got advice that the problem might be with the FAT filesystem. I decided to try and format the stick to NTSF (format G:/fs:ntsf) but the formatting failed and the drive broke down. And with breaking down I mean you cannot access the drive anymore and when you plug it in Windows asks if I want to format the drive but despite my will the format always fails. To fix this I tried changing it back to FAT32 (format G:/fs:fat32), but i get "Error in IOCTL-call". Second thing I tried was trying to reset the filesystem with some 3rd party application like HP USB Disk Storage Format Tool. But the programs didn´t regocnize any media on the drive. So now I´m in the situation that I haven´t got any idea on what to do next. Is the drive recoverable or did I just create a piece of waste metal.

    Read the article

  • CentOS: AJAX/jQuery not working

    - by Australiya
    In a nutshell, I have an unmanaged VPS. At one time, it had Ubuntu 10.10 server on it, then I reinstalled it with CentOS 6 and updated it to CentOS 6.2. Now, the problem is, the AJAX/jQuery shoutbox has ceased working (I assume it uses one of the two to inject itself into a div and then refresh when new messages are posted, I'm not sure, I didn't write these), and the plug-board script now shows me a lime green blank page. No changes to the source codes have been made, and they are in the location they expect themselves to be. I have Apache2, MySQL 5, PHP 5, and I did install the php-xml libraries. What am I missing? It's gotta be server side because the scripts themselves are fine, if I move them to a different server they work just fine. I'm not getting any errors related to this in the error_log file. Thanks in advance! Edit: If you want, you can look at the plugboard at kazeshini.net/plugboard and there's an installation of the chatbox at silverlotus.kazeshini.net/yshout/example, I know nothing about scripts and debugging so better someone else looks at it than someone that doesn't know what they're looking for.

    Read the article

  • How many bootable partitions are possible to have on one hard drive?

    - by draiden
    This may not be the correct place to post this; if that's the case, just let me know and point me in the right direction please! I'm thinking of building a box that needs to be lightweight and portable, and would need to be able to boot multiple installations of windows. I am needing to have multiple installations so that I can, for example, plug the box in to the network at one location, boot in to that location's partition, and have full access to everything I would normally need to do on a computer that has already been set up on that network. Then, when I go to the next client, I would be able to do the same thing, with the new location's partition, and have all of those network settings, drive mappings, etc., available there. Obviously I'd need to go through and set them all up on the different locations/networks, I'm not expecting it to magically know where I am and what I'm doing. It would be like I'm carrying around a computer that is configured for each place I need to go in one little box, instead of having to have multiple computers or having to reconfigure all the settings and such every time I go to another client. Or is there an easier way to do this that I haven't learned of?

    Read the article

  • Set up layer 2 vlan between 2 data centres

    - by user41679
    Hello, Our data centre provider operates 2 sites, and we currently have equipment in one and would like to have equipment in the second. They've told me that they operate a layer 2 vlan between the 2 sites over a 20gbit connection, and that they'd just give me ethernet cable at each end to connect the locations. At the current site, we have Cisco 2960 48TC-L switches, all the machines are on a 192.168.x.x subnet and we have cisco firewalls with which we connect to our internet provider with. My question is what would I need to do to connect the 2 sites? could I just plug the ethernet cables the provide into the cisco switches, and have the same switches the other end? would I need to set up a separate internal network on the other side and connect both through the firewalls? Would the cisco switches need special configuration? We expect to maintain a number of connections between the 2 sites, and each site would have its own internal dns name like dc1.xx.com. Sorry if I'm being vague or haven't included enough information, I've a fairly good knowledge of hardware but we're down a netops guy at the moment and I'd like to get both sites on-line ASAP! Thanks in advance!

    Read the article

  • How to minimize the risk of employees spreading critical information? [closed]

    - by Industrial
    What's common sense when it comes to minimising the risk of employees spreading critical information to rivalling companies? As of today, it's clear that not even the US government and military can be sure that their data stays safely within their doors. Thereby I understand that my question probably instead should be written as "What is common sense to make it harder for employees to spread business critical information?" If anyone would want to spread information, they will find a way. That's the way life work and always has. If we make the scenario a bit more realistic by narrowing our workforce by assuming we only have regular John Does onboard and not Linux-loving sysadmins , what should be good precautions to at least make it harder for the employees to send business-critical information to the competition? As far as I can tell, there's a few obvious solutions that clearly has both pros and cons: Block services such as Dropbox and similar, preventing anyone to send gigabytes of data through the wire. Ensure that only files below a set size can be sent as email (?) Setup VLANs between departments to make it harder for kleptomaniacs and curious people to snoop around. Plug all removable media units - CD/DVD, Floppy drives and USB Make sure that no configurations to hardware can be made (?) Monitor network traffic for non-linear events (how?) What is realistic to do in a real world? How does big companies handle this? Sure, we can take the former employer to court and sue, but by then the damage has already been caused... Thanks a lot

    Read the article

  • How to turn a DSL wireless modem to a wifi hub

    - by my_question
    I used to use DSL for my home internet and used Qwest Q1000 wireless modem. Now I switched to cable and use wireless router to cover the home. One problem is I just bought a desktop and I like to put it in a place far away from the router. The desktop only has cable interface, it does not receive wifi. The obvious solution is I go buy that little USB dongle which can receive wifi and plug it to the desktop. But before doig that, I am wondering if somehow I can re-use the Q1000 modem. The modem has 4 LAN ports and it has wifi antenna. I tried connecting the desktop to Q1000's LAN port, the system shows wire connection is in place, but I cannot access internet. It seems to me Q1000's wifi function is to broadcast the wifi signal out instead of receiving signal. I went to the Q1000 configuration page by going to web page of "192.168.0.1", it is not clear how to set it up. I also wonder one thing, my home wifi is encrypted, so if I want to let Q1000 to join the wifi, I need to somehow type in the password, I am not sure how to do that either. Anyway, maybe this thing cannot be used in this fashion. If you have any suggestion, please shed some light. Thanks.

    Read the article

  • Cannot open /dev/rfcomm1 : Host is down

    - by srj0408
    I am working on raspberry PI and on Bluetooth. I am using old raspberry pi kernel as the new one has got some bugs that were not resolved with respect to the bluez daemon. At present my kernel version is 3.6.11. I am using a USB bluetooth dongle and my sole purpose is to auto connect the bluetooth dongle when ever it is in range. For that i think i have to run a script in the backend on RPI that will keep on checking the existence of usb bluetooth dongle. I started from the very scratch. I installed bluez daemon using apt-get install bluetooth bluez utils blueman and then i used hciconfig which gives me that my bluetooth usb dongle is working fine. But when i did hcitool scan , it give me no device in range even though my Serial bluetooth Device was on. I wasn't able to find any device in vicinity. Also when i unplugged and plug the USB dongle again, i was able to scan the serial device , but when i repeat the process, i find the earlier condition of not finding any deice. I had find another useful link, but that need address of the bluetooth device that need to be connected. I want to automate this using hcitool scan, storing the output to the a file and then comparing it with already paired devices and their name. For that i need to figure out why hcitool scan is sometime working and sometime not. ? Can some one help me in figuring out why this is happening. Is there any problem on hardware side i.e Bluetooth dongle is buggy or i had some problem in bluez utils. Edit 1: While as of now, hcitool scan is giving me my remote device address but still i am getting the same issue of HOUST IS DOWN, '/dev/rfcomm1'. I am really not getting any idea of what to be done.

    Read the article

  • Including an embedded framework using a cross-project-reference: Header no such file or directory

    - by d11wtq
    I'm trying to create a Cocoa framework by using a cross-project reference in Xcode. I have 2 projects: one for the framework; one for the application that will use the framework. This framework is not intended to be stored within the system; it is an embedded framework that lives within the application bundle. I have successfully made the cross-project reference, marked the framework as being a dependency of my target, added a Copy Files build phase that puts the framework in Contents/Frameworks/ and added the framework to the linker phase (I checked the little "Target" checkbox; I've also done it manually by dragging the framework into the linker phase). My framework's install directory is correctly set to @executable_path/../Frameworks. However, when I try to build my app it: a) Correctly builds the framework first b) Correctly copies the framework c) Errors because it cannot find the master header file in my framework I have verified that the header is there. I can see it in the app product that is partially built. ls build/Debug/CioccolataTest.webapp/Contents/Frameworks/Cioccolata.framework/Headers/Cioccolata.h build/Debug/CioccolataTest.webapp/Contents/Frameworks/Cioccolata.framework/Headers/Cioccolata.h I have been able to successfully build the app by copying my framework into /Library/Frameworks (I can then delete it again after the successful build), but this is a workaround, I'm looking to find it out why Xcode doesn't find the framework's master header file without it being copied to a system directory. Is copying it to the app bundle during the build not sufficient? Here's the full build transcript if it's any help (it's just a Hello World app right now, so not much going on here): Build Cioccolata of project Cioccolata with configuration Debug SymLink /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Versions/Current A cd /Users/chris/Projects/Mac/Cioccolata /bin/ln -sf A /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Versions/Current SymLink /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Resources Versions/Current/Resources cd /Users/chris/Projects/Mac/Cioccolata /bin/ln -sf Versions/Current/Resources /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Resources SymLink /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Headers Versions/Current/Headers cd /Users/chris/Projects/Mac/Cioccolata /bin/ln -sf Versions/Current/Headers /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Headers SymLink /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Cioccolata Versions/Current/Cioccolata cd /Users/chris/Projects/Mac/Cioccolata /bin/ln -sf Versions/Current/Cioccolata /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Cioccolata ProcessInfoPlistFile /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Versions/A/Resources/Info.plist Info.plist cd /Users/chris/Projects/Mac/Cioccolata builtin-infoPlistUtility Info.plist -expandbuildsettings -platform macosx -o /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Versions/A/Resources/Info.plist CpHeader build/Debug/Cioccolata.framework/Versions/A/Headers/CWHelloWorld.h CWHelloWorld.h cd /Users/chris/Projects/Mac/Cioccolata /Developer/Library/PrivateFrameworks/DevToolsCore.framework/Resources/pbxcp -exclude .DS_Store -exclude CVS -exclude .svn -resolve-src-symlinks /Users/chris/Projects/Mac/Cioccolata/CWHelloWorld.h /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Versions/A/Headers CpHeader build/Debug/Cioccolata.framework/Versions/A/Headers/Cioccolata.h Cioccolata.h cd /Users/chris/Projects/Mac/Cioccolata /Developer/Library/PrivateFrameworks/DevToolsCore.framework/Resources/pbxcp -exclude .DS_Store -exclude CVS -exclude .svn -resolve-src-symlinks /Users/chris/Projects/Mac/Cioccolata/Cioccolata.h /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Versions/A/Headers CopyStringsFile /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Versions/A/Resources/English.lproj/InfoPlist.strings English.lproj/InfoPlist.strings cd /Users/chris/Projects/Mac/Cioccolata setenv ICONV /usr/bin/iconv /Developer/Library/Xcode/Plug-ins/CoreBuildTasks.xcplugin/Contents/Resources/copystrings --validate --inputencoding utf-8 --outputencoding UTF-16 English.lproj/InfoPlist.strings --outdir /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Versions/A/Resources/English.lproj ProcessPCH /var/folders/Xy/Xy-bvnxtFpiYBQPED0dK1++++TI/-Caches-/com.apple.Xcode.501/SharedPrecompiledHeaders/Cioccolata_Prefix-dololiigmwjzkgenggebqtpvbauu/Cioccolata_Prefix.pch.gch Cioccolata_Prefix.pch normal i386 objective-c com.apple.compilers.gcc.4_2 cd /Users/chris/Projects/Mac/Cioccolata setenv LANG en_US.US-ASCII /Developer/usr/bin/gcc-4.2 -x objective-c-header -arch i386 -fmessage-length=0 -pipe -std=gnu99 -Wno-trigraphs -fpascal-strings -fasm-blocks -O0 -Wreturn-type -Wunused-variable -isysroot /Developer/SDKs/MacOSX10.5.sdk -mfix-and-continue -mmacosx-version-min=10.5 -gdwarf-2 -iquote /Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/Cioccolata-generated-files.hmap -I/Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/Cioccolata-own-target-headers.hmap -I/Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/Cioccolata-all-target-headers.hmap -iquote /Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/Cioccolata-project-headers.hmap -F/Users/chris/Projects/Mac/Cioccolata/build/Debug -I/Users/chris/Projects/Mac/Cioccolata/build/Debug/include -I/Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/DerivedSources/i386 -I/Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/DerivedSources -c /Users/chris/Projects/Mac/Cioccolata/Cioccolata_Prefix.pch -o /var/folders/Xy/Xy-bvnxtFpiYBQPED0dK1++++TI/-Caches-/com.apple.Xcode.501/SharedPrecompiledHeaders/Cioccolata_Prefix-dololiigmwjzkgenggebqtpvbauu/Cioccolata_Prefix.pch.gch CompileC build/Cioccolata.build/Debug/Cioccolata.build/Objects-normal/i386/CWHelloWorld.o /Users/chris/Projects/Mac/Cioccolata/CWHelloWorld.m normal i386 objective-c com.apple.compilers.gcc.4_2 cd /Users/chris/Projects/Mac/Cioccolata setenv LANG en_US.US-ASCII /Developer/usr/bin/gcc-4.2 -x objective-c -arch i386 -fmessage-length=0 -pipe -std=gnu99 -Wno-trigraphs -fpascal-strings -fasm-blocks -O0 -Wreturn-type -Wunused-variable -isysroot /Developer/SDKs/MacOSX10.5.sdk -mfix-and-continue -mmacosx-version-min=10.5 -gdwarf-2 -iquote /Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/Cioccolata-generated-files.hmap -I/Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/Cioccolata-own-target-headers.hmap -I/Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/Cioccolata-all-target-headers.hmap -iquote /Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/Cioccolata-project-headers.hmap -F/Users/chris/Projects/Mac/Cioccolata/build/Debug -I/Users/chris/Projects/Mac/Cioccolata/build/Debug/include -I/Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/DerivedSources/i386 -I/Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/DerivedSources -include /var/folders/Xy/Xy-bvnxtFpiYBQPED0dK1++++TI/-Caches-/com.apple.Xcode.501/SharedPrecompiledHeaders/Cioccolata_Prefix-dololiigmwjzkgenggebqtpvbauu/Cioccolata_Prefix.pch -c /Users/chris/Projects/Mac/Cioccolata/CWHelloWorld.m -o /Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/Objects-normal/i386/CWHelloWorld.o Ld /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Versions/A/Cioccolata normal i386 cd /Users/chris/Projects/Mac/Cioccolata setenv MACOSX_DEPLOYMENT_TARGET 10.5 /Developer/usr/bin/gcc-4.2 -arch i386 -dynamiclib -isysroot /Developer/SDKs/MacOSX10.5.sdk -L/Users/chris/Projects/Mac/Cioccolata/build/Debug -F/Users/chris/Projects/Mac/Cioccolata/build/Debug -filelist /Users/chris/Projects/Mac/Cioccolata/build/Cioccolata.build/Debug/Cioccolata.build/Objects-normal/i386/Cioccolata.LinkFileList -install_name @executable_path/../Frameworks/Cioccolata.framework/Versions/A/Cioccolata -mmacosx-version-min=10.5 -framework Foundation -single_module -compatibility_version 1 -current_version 1 -o /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework/Versions/A/Cioccolata Touch /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework cd /Users/chris/Projects/Mac/Cioccolata /usr/bin/touch -c /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework Build CioccolataTest of project CioccolataTest with configuration Debug ProcessInfoPlistFile /Users/chris/Projects/Mac/CioccolataTest/build/Debug/CioccolataTest.webapp/Contents/Info.plist Info.plist cd /Users/chris/Projects/Mac/CioccolataTest builtin-infoPlistUtility Info.plist -expandbuildsettings -platform macosx -o /Users/chris/Projects/Mac/CioccolataTest/build/Debug/CioccolataTest.webapp/Contents/Info.plist PBXCp build/Debug/CioccolataTest.webapp/Contents/Frameworks/Cioccolata.framework /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework cd /Users/chris/Projects/Mac/CioccolataTest /Developer/Library/PrivateFrameworks/DevToolsCore.framework/Resources/pbxcp -exclude .DS_Store -exclude CVS -exclude .svn -resolve-src-symlinks /Users/chris/Projects/Mac/Cioccolata/build/Debug/Cioccolata.framework /Users/chris/Projects/Mac/CioccolataTest/build/Debug/CioccolataTest.webapp/Contents/Frameworks CopyStringsFile /Users/chris/Projects/Mac/CioccolataTest/build/Debug/CioccolataTest.webapp/Contents/Resources/English.lproj/InfoPlist.strings English.lproj/InfoPlist.strings cd /Users/chris/Projects/Mac/CioccolataTest setenv ICONV /usr/bin/iconv /Developer/Library/Xcode/Plug-ins/CoreBuildTasks.xcplugin/Contents/Resources/copystrings --validate --inputencoding utf-8 --outputencoding UTF-16 English.lproj/InfoPlist.strings --outdir /Users/chris/Projects/Mac/CioccolataTest/build/Debug/CioccolataTest.webapp/Contents/Resources/English.lproj CompileC build/CioccolataTest.build/Debug/CioccolataTest.build/Objects-normal/i386/main.o main.m normal i386 objective-c com.apple.compilers.gcc.4_2 cd /Users/chris/Projects/Mac/CioccolataTest setenv LANG en_US.US-ASCII /Developer/usr/bin/gcc-4.2 -x objective-c -arch i386 -fmessage-length=0 -pipe -std=gnu99 -Wno-trigraphs -fpascal-strings -fasm-blocks -O0 -Wreturn-type -Wunused-variable -isysroot /Developer/SDKs/MacOSX10.5.sdk -mfix-and-continue -mmacosx-version-min=10.5 -gdwarf-2 -iquote /Users/chris/Projects/Mac/CioccolataTest/build/CioccolataTest.build/Debug/CioccolataTest.build/CioccolataTest-generated-files.hmap -I/Users/chris/Projects/Mac/CioccolataTest/build/CioccolataTest.build/Debug/CioccolataTest.build/CioccolataTest-own-target-headers.hmap -I/Users/chris/Projects/Mac/CioccolataTest/build/CioccolataTest.build/Debug/CioccolataTest.build/CioccolataTest-all-target-headers.hmap -iquote /Users/chris/Projects/Mac/CioccolataTest/build/CioccolataTest.build/Debug/CioccolataTest.build/CioccolataTest-project-headers.hmap -F/Users/chris/Projects/Mac/CioccolataTest/build/Debug -I/Users/chris/Projects/Mac/CioccolataTest/build/Debug/include -I/Users/chris/Projects/Mac/CioccolataTest/build/CioccolataTest.build/Debug/CioccolataTest.build/DerivedSources/i386 -I/Users/chris/Projects/Mac/CioccolataTest/build/CioccolataTest.build/Debug/CioccolataTest.build/DerivedSources -include /Users/chris/Projects/Mac/CioccolataTest/prefix.pch -c /Users/chris/Projects/Mac/CioccolataTest/main.m -o /Users/chris/Projects/Mac/CioccolataTest/build/CioccolataTest.build/Debug/CioccolataTest.build/Objects-normal/i386/main.o In file included from <command-line>:0: /Users/chris/Projects/Mac/CioccolataTest/prefix.pch:13:35: error: Cioccolata/Cioccolata.h: No such file or directory /Users/chris/Projects/Mac/CioccolataTest/main.m: In function 'main': /Users/chris/Projects/Mac/CioccolataTest/main.m:13: error: 'CWHelloWorld' undeclared (first use in this function) /Users/chris/Projects/Mac/CioccolataTest/main.m:13: error: (Each undeclared identifier is reported only once /Users/chris/Projects/Mac/CioccolataTest/main.m:13: error: for each function it appears in.) /Users/chris/Projects/Mac/CioccolataTest/main.m:13: error: 'hello' undeclared (first use in this function)

    Read the article

  • TSQL Conditionally Select Specific Value

    - by Dzejms
    This is a follow-up to #1644748 where I successfully answered my own question, but Quassnoi helped me to realize that it was the wrong question. He gave me a solution that worked for my sample data, but I couldn't plug it back into the parent stored procedure because I fail at SQL 2005 syntax. So here is an attempt to paint the broader picture and ask what I actually need. This is part of a stored procedure that returns a list of items in a bug tracking application I've inherited. There are are over 100 fields and 26 joins so I'm pulling out only the mostly relevant bits. SELECT tickets.ticketid, tickets.tickettype, tickets_tickettype_lu.tickettypedesc, tickets.stage, tickets.position, tickets.sponsor, tickets.dev, tickets.qa, DATEDIFF(DAY, ticket_history_assignment.savedate, GETDATE()) as 'daysinqueue' FROM dbo.tickets WITH (NOLOCK) LEFT OUTER JOIN dbo.tickets_tickettype_lu WITH (NOLOCK) ON tickets.tickettype = tickets_tickettype_lu.tickettypeid LEFT OUTER JOIN dbo.tickets_history_assignment WITH (NOLOCK) ON tickets_history_assignment.ticketid = tickets.ticketid AND tickets_history_assignment.historyid = ( SELECT MAX(historyid) FROM dbo.tickets_history_assignment WITH (NOLOCK) WHERE tickets_history_assignment.ticketid = tickets.ticketid GROUP BY tickets_history_assignment.ticketid ) WHERE tickets.sponsor = @sponsor The area of interest is the daysinqueue subquery mess. The tickets_history_assignment table looks roughly as follows declare @tickets_history_assignment table ( historyid int, ticketid int, sponsor int, dev int, qa int, savedate datetime ) insert into @tickets_history_assignment values (1521402, 92774,20,14, 20, '2009-10-27 09:17:59.527') insert into @tickets_history_assignment values (1521399, 92774,20,14, 42, '2009-08-31 12:07:52.917') insert into @tickets_history_assignment values (1521311, 92774,100,14, 42, '2008-12-08 16:15:49.887') insert into @tickets_history_assignment values (1521336, 92774,100,14, 42, '2009-01-16 14:27:43.577') Whenever a ticket is saved, the current values for sponsor, dev and qa are stored in the tickets_history_assignment table with the ticketid and a timestamp. So it is possible for someone to change the value for qa, but leave sponsor alone. What I want to know, based on all of these conditions, is the historyid of the record in the tickets_history_assignment table where the sponsor value was last changed so that I can calculate the value for daysinqueue. If a record is inserted into the history table, and only the qa value has changed, I don't want that record. So simply relying on MAX(historyid) won't work for me. Quassnoi came up with the following which seemed to work with my sample data, but I can't plug it into the larger query, SQL Manager bitches about the WITH statement. ;WITH rows AS ( SELECT *, ROW_NUMBER() OVER (PARTITION BY ticketid ORDER BY savedate DESC) AS rn FROM @Table ) SELECT rl.sponsor, ro.savedate FROM rows rl CROSS APPLY ( SELECT TOP 1 rc.savedate FROM rows rc JOIN rows rn ON rn.ticketid = rc.ticketid AND rn.rn = rc.rn + 1 AND rn.sponsor <> rc.sponsor WHERE rc.ticketid = rl.ticketid ORDER BY rc.rn ) ro WHERE rl.rn = 1 I played with it yesterday afternoon and got nowhere because I don't fundamentally understand what is going on here and how it should fit into the larger context. So, any takers? UPDATE Ok, here's the whole thing. I've been switching some of the table and column names in an attempt to simplify things so here's the full unedited mess. snip - old bad code Here are the errors: Msg 102, Level 15, State 1, Procedure usp_GetProjectRecordsByAssignment, Line 159 Incorrect syntax near ';'. Msg 102, Level 15, State 1, Procedure usp_GetProjectRecordsByAssignment, Line 179 Incorrect syntax near ')'. Line numbers are of course not correct but refer to ;WITH rows AS And the ')' char after the WHERE rl.rn = 1 ) Respectively Is there a tag for extra super long question? UPDATE #2 Here is the finished query for anyone who may need this: CREATE PROCEDURE [dbo].[usp_GetProjectRecordsByAssignment] ( @assigned numeric(18,0), @assignedtype numeric(18,0) ) AS SET NOCOUNT ON WITH rows AS ( SELECT *, ROW_NUMBER() OVER (PARTITION BY recordid ORDER BY savedate DESC) AS rn FROM projects_history_assignment ) SELECT projects_records.recordid, projects_records.recordtype, projects_recordtype_lu.recordtypedesc, projects_records.stage, projects_stage_lu.stagedesc, projects_records.position, projects_position_lu.positiondesc, CASE projects_records.clientrequested WHEN '1' THEN 'Yes' WHEN '0' THEN 'No' END AS clientrequested, projects_records.reportingmethod, projects_reportingmethod_lu.reportingmethoddesc, projects_records.clientaccess, projects_clientaccess_lu.clientaccessdesc, projects_records.clientnumber, projects_records.project, projects_lu.projectdesc, projects_records.version, projects_version_lu.versiondesc, projects_records.projectedversion, projects_version_lu_projected.versiondesc AS projectedversiondesc, projects_records.sitetype, projects_sitetype_lu.sitetypedesc, projects_records.title, projects_records.module, projects_module_lu.moduledesc, projects_records.component, projects_component_lu.componentdesc, projects_records.loginusername, projects_records.loginpassword, projects_records.assistedusername, projects_records.browsername, projects_browsername_lu.browsernamedesc, projects_records.browserversion, projects_records.osname, projects_osname_lu.osnamedesc, projects_records.osversion, projects_records.errortype, projects_errortype_lu.errortypedesc, projects_records.gsipriority, projects_gsipriority_lu.gsiprioritydesc, projects_records.clientpriority, projects_clientpriority_lu.clientprioritydesc, projects_records.scheduledstartdate, projects_records.scheduledcompletiondate, projects_records.projectedhours, projects_records.actualstartdate, projects_records.actualcompletiondate, projects_records.actualhours, CASE projects_records.billclient WHEN '1' THEN 'Yes' WHEN '0' THEN 'No' END AS billclient, projects_records.billamount, projects_records.status, projects_status_lu.statusdesc, CASE CAST(projects_records.assigned AS VARCHAR(5)) WHEN '0' THEN 'N/A' WHEN '10000' THEN 'Unassigned' WHEN '20000' THEN 'Client' WHEN '30000' THEN 'Tech Support' WHEN '40000' THEN 'LMI Tech Support' WHEN '50000' THEN 'Upload' WHEN '60000' THEN 'Spider' WHEN '70000' THEN 'DB Admin' ELSE rtrim(users_assigned.nickname) + ' ' + rtrim(users_assigned.lastname) END AS assigned, CASE CAST(projects_records.assigneddev AS VARCHAR(5)) WHEN '0' THEN 'N/A' WHEN '10000' THEN 'Unassigned' ELSE rtrim(users_assigneddev.nickname) + ' ' + rtrim(users_assigneddev.lastname) END AS assigneddev, CASE CAST(projects_records.assignedqa AS VARCHAR(5)) WHEN '0' THEN 'N/A' WHEN '10000' THEN 'Unassigned' ELSE rtrim(users_assignedqa.nickname) + ' ' + rtrim(users_assignedqa.lastname) END AS assignedqa, CASE CAST(projects_records.assignedsponsor AS VARCHAR(5)) WHEN '0' THEN 'N/A' WHEN '10000' THEN 'Unassigned' ELSE rtrim(users_assignedsponsor.nickname) + ' ' + rtrim(users_assignedsponsor.lastname) END AS assignedsponsor, projects_records.clientcreated, CASE projects_records.clientcreated WHEN '1' THEN 'Yes' WHEN '0' THEN 'No' END AS clientcreateddesc, CASE projects_records.clientcreated WHEN '1' THEN rtrim(clientusers_createuser.firstname) + ' ' + rtrim(clientusers_createuser.lastname) + ' (Client)' ELSE rtrim(users_createuser.nickname) + ' ' + rtrim(users_createuser.lastname) END AS createuser, projects_records.createdate, projects_records.savedate, projects_resolution.sitesaffected, projects_sitesaffected_lu.sitesaffecteddesc, DATEDIFF(DAY, projects_history_assignment.savedate, GETDATE()) as 'daysinqueue', projects_records.iOnHitList, projects_records.changetype FROM dbo.projects_records WITH (NOLOCK) LEFT OUTER JOIN dbo.projects_recordtype_lu WITH (NOLOCK) ON projects_records.recordtype = projects_recordtype_lu.recordtypeid LEFT OUTER JOIN dbo.projects_stage_lu WITH (NOLOCK) ON projects_records.stage = projects_stage_lu.stageid LEFT OUTER JOIN dbo.projects_position_lu WITH (NOLOCK) ON projects_records.position = projects_position_lu.positionid LEFT OUTER JOIN dbo.projects_reportingmethod_lu WITH (NOLOCK) ON projects_records.reportingmethod = projects_reportingmethod_lu.reportingmethodid LEFT OUTER JOIN dbo.projects_lu WITH (NOLOCK) ON projects_records.project = projects_lu.projectid LEFT OUTER JOIN dbo.projects_version_lu WITH (NOLOCK) ON projects_records.version = projects_version_lu.versionid LEFT OUTER JOIN dbo.projects_version_lu projects_version_lu_projected WITH (NOLOCK) ON projects_records.projectedversion = projects_version_lu_projected.versionid LEFT OUTER JOIN dbo.projects_sitetype_lu WITH (NOLOCK) ON projects_records.sitetype = projects_sitetype_lu.sitetypeid LEFT OUTER JOIN dbo.projects_module_lu WITH (NOLOCK) ON projects_records.module = projects_module_lu.moduleid LEFT OUTER JOIN dbo.projects_component_lu WITH (NOLOCK) ON projects_records.component = projects_component_lu.componentid LEFT OUTER JOIN dbo.projects_browsername_lu WITH (NOLOCK) ON projects_records.browsername = projects_browsername_lu.browsernameid LEFT OUTER JOIN dbo.projects_osname_lu WITH (NOLOCK) ON projects_records.osname = projects_osname_lu.osnameid LEFT OUTER JOIN dbo.projects_errortype_lu WITH (NOLOCK) ON projects_records.errortype = projects_errortype_lu.errortypeid LEFT OUTER JOIN dbo.projects_resolution WITH (NOLOCK) ON projects_records.recordid = projects_resolution.recordid LEFT OUTER JOIN dbo.projects_sitesaffected_lu WITH (NOLOCK) ON projects_resolution.sitesaffected = projects_sitesaffected_lu.sitesaffectedid LEFT OUTER JOIN dbo.projects_gsipriority_lu WITH (NOLOCK) ON projects_records.gsipriority = projects_gsipriority_lu.gsipriorityid LEFT OUTER JOIN dbo.projects_clientpriority_lu WITH (NOLOCK) ON projects_records.clientpriority = projects_clientpriority_lu.clientpriorityid LEFT OUTER JOIN dbo.projects_status_lu WITH (NOLOCK) ON projects_records.status = projects_status_lu.statusid LEFT OUTER JOIN dbo.projects_clientaccess_lu WITH (NOLOCK) ON projects_records.clientaccess = projects_clientaccess_lu.clientaccessid LEFT OUTER JOIN dbo.users users_assigned WITH (NOLOCK) ON projects_records.assigned = users_assigned.userid LEFT OUTER JOIN dbo.users users_assigneddev WITH (NOLOCK) ON projects_records.assigneddev = users_assigneddev.userid LEFT OUTER JOIN dbo.users users_assignedqa WITH (NOLOCK) ON projects_records.assignedqa = users_assignedqa.userid LEFT OUTER JOIN dbo.users users_assignedsponsor WITH (NOLOCK) ON projects_records.assignedsponsor = users_assignedsponsor.userid LEFT OUTER JOIN dbo.users users_createuser WITH (NOLOCK) ON projects_records.createuser = users_createuser.userid LEFT OUTER JOIN dbo.clientusers clientusers_createuser WITH (NOLOCK) ON projects_records.createuser = clientusers_createuser.userid LEFT OUTER JOIN dbo.projects_history_assignment WITH (NOLOCK) ON projects_history_assignment.recordid = projects_records.recordid AND projects_history_assignment.historyid = ( SELECT ro.historyid FROM rows rl CROSS APPLY ( SELECT TOP 1 rc.historyid FROM rows rc JOIN rows rn ON rn.recordid = rc.recordid AND rn.rn = rc.rn + 1 AND rn.assigned <> rc.assigned WHERE rc.recordid = rl.recordid ORDER BY rc.rn ) ro WHERE rl.rn = 1 AND rl.recordid = projects_records.recordid ) WHERE (@assignedtype='0' and projects_records.assigned = @assigned) OR (@assignedtype='1' and projects_records.assigneddev = @assigned) OR (@assignedtype='2' and projects_records.assignedqa = @assigned) OR (@assignedtype='3' and projects_records.assignedsponsor = @assigned) OR (@assignedtype='4' and projects_records.createuser = @assigned)

    Read the article

  • An Introduction to ASP.NET Web API

    - by Rick Strahl
    Microsoft recently released ASP.NET MVC 4.0 and .NET 4.5 and along with it, the brand spanking new ASP.NET Web API. Web API is an exciting new addition to the ASP.NET stack that provides a new, well-designed HTTP framework for creating REST and AJAX APIs (API is Microsoft’s new jargon for a service, in case you’re wondering). Although Web API ships and installs with ASP.NET MVC 4, you can use Web API functionality in any ASP.NET project, including WebForms, WebPages and MVC or just a Web API by itself. And you can also self-host Web API in your own applications from Console, Desktop or Service applications. If you're interested in a high level overview on what ASP.NET Web API is and how it fits into the ASP.NET stack you can check out my previous post: Where does ASP.NET Web API fit? In the following article, I'll focus on a practical, by example introduction to ASP.NET Web API. All the code discussed in this article is available in GitHub: https://github.com/RickStrahl/AspNetWebApiArticle [republished from my Code Magazine Article and updated for RTM release of ASP.NET Web API] Getting Started To start I’ll create a new empty ASP.NET application to demonstrate that Web API can work with any kind of ASP.NET project. Although you can create a new project based on the ASP.NET MVC/Web API template to quickly get up and running, I’ll take you through the manual setup process, because one common use case is to add Web API functionality to an existing ASP.NET application. This process describes the steps needed to hook up Web API to any ASP.NET 4.0 application. Start by creating an ASP.NET Empty Project. Then create a new folder in the project called Controllers. Add a Web API Controller Class Once you have any kind of ASP.NET project open, you can add a Web API Controller class to it. Web API Controllers are very similar to MVC Controller classes, but they work in any kind of project. Add a new item to this folder by using the Add New Item option in Visual Studio and choose Web API Controller Class, as shown in Figure 1. Figure 1: This is how you create a new Controller Class in Visual Studio   Make sure that the name of the controller class includes Controller at the end of it, which is required in order for Web API routing to find it. Here, the name for the class is AlbumApiController. For this example, I’ll use a Music Album model to demonstrate basic behavior of Web API. The model consists of albums and related songs where an album has properties like Name, Artist and YearReleased and a list of songs with a SongName and SongLength as well as an AlbumId that links it to the album. You can find the code for the model (and the rest of these samples) on Github. To add the file manually, create a new folder called Model, and add a new class Album.cs and copy the code into it. There’s a static AlbumData class with a static CreateSampleAlbumData() method that creates a short list of albums on a static .Current that I’ll use for the examples. Before we look at what goes into the controller class though, let’s hook up routing so we can access this new controller. Hooking up Routing in Global.asax To start, I need to perform the one required configuration task in order for Web API to work: I need to configure routing to the controller. Like MVC, Web API uses routing to provide clean, extension-less URLs to controller methods. Using an extension method to ASP.NET’s static RouteTable class, you can use the MapHttpRoute() (in the System.Web.Http namespace) method to hook-up the routing during Application_Start in global.asax.cs shown in Listing 1.using System; using System.Web.Routing; using System.Web.Http; namespace AspNetWebApi { public class Global : System.Web.HttpApplication { protected void Application_Start(object sender, EventArgs e) { RouteTable.Routes.MapHttpRoute( name: "AlbumVerbs", routeTemplate: "albums/{title}", defaults: new { symbol = RouteParameter.Optional, controller="AlbumApi" } ); } } } This route configures Web API to direct URLs that start with an albums folder to the AlbumApiController class. Routing in ASP.NET is used to create extensionless URLs and allows you to map segments of the URL to specific Route Value parameters. A route parameter, with a name inside curly brackets like {name}, is mapped to parameters on the controller methods. Route parameters can be optional, and there are two special route parameters – controller and action – that determine the controller to call and the method to activate respectively. HTTP Verb Routing Routing in Web API can route requests by HTTP Verb in addition to standard {controller},{action} routing. For the first examples, I use HTTP Verb routing, as shown Listing 1. Notice that the route I’ve defined does not include an {action} route value or action value in the defaults. Rather, Web API can use the HTTP Verb in this route to determine the method to call the controller, and a GET request maps to any method that starts with Get. So methods called Get() or GetAlbums() are matched by a GET request and a POST request maps to a Post() or PostAlbum(). Web API matches a method by name and parameter signature to match a route, query string or POST values. In lieu of the method name, the [HttpGet,HttpPost,HttpPut,HttpDelete, etc] attributes can also be used to designate the accepted verbs explicitly if you don’t want to follow the verb naming conventions. Although HTTP Verb routing is a good practice for REST style resource APIs, it’s not required and you can still use more traditional routes with an explicit {action} route parameter. When {action} is supplied, the HTTP verb routing is ignored. I’ll talk more about alternate routes later. When you’re finished with initial creation of files, your project should look like Figure 2.   Figure 2: The initial project has the new API Controller Album model   Creating a small Album Model Now it’s time to create some controller methods to serve data. For these examples, I’ll use a very simple Album and Songs model to play with, as shown in Listing 2. public class Song { public string AlbumId { get; set; } [Required, StringLength(80)] public string SongName { get; set; } [StringLength(5)] public string SongLength { get; set; } } public class Album { public string Id { get; set; } [Required, StringLength(80)] public string AlbumName { get; set; } [StringLength(80)] public string Artist { get; set; } public int YearReleased { get; set; } public DateTime Entered { get; set; } [StringLength(150)] public string AlbumImageUrl { get; set; } [StringLength(200)] public string AmazonUrl { get; set; } public virtual List<Song> Songs { get; set; } public Album() { Songs = new List<Song>(); Entered = DateTime.Now; // Poor man's unique Id off GUID hash Id = Guid.NewGuid().GetHashCode().ToString("x"); } public void AddSong(string songName, string songLength = null) { this.Songs.Add(new Song() { AlbumId = this.Id, SongName = songName, SongLength = songLength }); } } Once the model has been created, I also added an AlbumData class that generates some static data in memory that is loaded onto a static .Current member. The signature of this class looks like this and that's what I'll access to retrieve the base data:public static class AlbumData { // sample data - static list public static List<Album> Current = CreateSampleAlbumData(); /// <summary> /// Create some sample data /// </summary> /// <returns></returns> public static List<Album> CreateSampleAlbumData() { … }} You can check out the full code for the data generation online. Creating an AlbumApiController Web API shares many concepts of ASP.NET MVC, and the implementation of your API logic is done by implementing a subclass of the System.Web.Http.ApiController class. Each public method in the implemented controller is a potential endpoint for the HTTP API, as long as a matching route can be found to invoke it. The class name you create should end in Controller, which is how Web API matches the controller route value to figure out which class to invoke. Inside the controller you can implement methods that take standard .NET input parameters and return .NET values as results. Web API’s binding tries to match POST data, route values, form values or query string values to your parameters. Because the controller is configured for HTTP Verb based routing (no {action} parameter in the route), any methods that start with Getxxxx() are called by an HTTP GET operation. You can have multiple methods that match each HTTP Verb as long as the parameter signatures are different and can be matched by Web API. In Listing 3, I create an AlbumApiController with two methods to retrieve a list of albums and a single album by its title .public class AlbumApiController : ApiController { public IEnumerable<Album> GetAlbums() { var albums = AlbumData.Current.OrderBy(alb => alb.Artist); return albums; } public Album GetAlbum(string title) { var album = AlbumData.Current .SingleOrDefault(alb => alb.AlbumName.Contains(title)); return album; }} To access the first two requests, you can use the following URLs in your browser: http://localhost/aspnetWebApi/albumshttp://localhost/aspnetWebApi/albums/Dirty%20Deeds Note that you’re not specifying the actions of GetAlbum or GetAlbums in these URLs. Instead Web API’s routing uses HTTP GET verb to route to these methods that start with Getxxx() with the first mapping to the parameterless GetAlbums() method and the latter to the GetAlbum(title) method that receives the title parameter mapped as optional in the route. Content Negotiation When you access any of the URLs above from a browser, you get either an XML or JSON result returned back. The album list result for Chrome 17 and Internet Explorer 9 is shown Figure 3. Figure 3: Web API responses can vary depending on the browser used, demonstrating Content Negotiation in action as these two browsers send different HTTP Accept headers.   Notice that the results are not the same: Chrome returns an XML response and IE9 returns a JSON response. Whoa, what’s going on here? Shouldn’t we see the same result in both browsers? Actually, no. Web API determines what type of content to return based on Accept headers. HTTP clients, like browsers, use Accept headers to specify what kind of content they’d like to see returned. Browsers generally ask for HTML first, followed by a few additional content types. Chrome (and most other major browsers) ask for: Accept: text/html, application/xhtml+xml,application/xml; q=0.9,*/*;q=0.8 IE9 asks for: Accept: text/html, application/xhtml+xml, */* Note that Chrome’s Accept header includes application/xml, which Web API finds in its list of supported media types and returns an XML response. IE9 does not include an Accept header type that works on Web API by default, and so it returns the default format, which is JSON. This is an important and very useful feature that was missing from any previous Microsoft REST tools: Web API automatically switches output formats based on HTTP Accept headers. Nowhere in the server code above do you have to explicitly specify the output format. Rather, Web API determines what format the client is requesting based on the Accept headers and automatically returns the result based on the available formatters. This means that a single method can handle both XML and JSON results.. Using this simple approach makes it very easy to create a single controller method that can return JSON, XML, ATOM or even OData feeds by providing the appropriate Accept header from the client. By default you don’t have to worry about the output format in your code. Note that you can still specify an explicit output format if you choose, either globally by overriding the installed formatters, or individually by returning a lower level HttpResponseMessage instance and setting the formatter explicitly. More on that in a minute. Along the same lines, any content sent to the server via POST/PUT is parsed by Web API based on the HTTP Content-type of the data sent. The same formats allowed for output are also allowed on input. Again, you don’t have to do anything in your code – Web API automatically performs the deserialization from the content. Accessing Web API JSON Data with jQuery A very common scenario for Web API endpoints is to retrieve data for AJAX calls from the Web browser. Because JSON is the default format for Web API, it’s easy to access data from the server using jQuery and its getJSON() method. This example receives the albums array from GetAlbums() and databinds it into the page using knockout.js.$.getJSON("albums/", function (albums) { // make knockout template visible $(".album").show(); // create view object and attach array var view = { albums: albums }; ko.applyBindings(view); }); Figure 4 shows this and the next example’s HTML output. You can check out the complete HTML and script code at http://goo.gl/Ix33C (.html) and http://goo.gl/tETlg (.js). Figu Figure 4: The Album Display sample uses JSON data loaded from Web API.   The result from the getJSON() call is a JavaScript object of the server result, which comes back as a JavaScript array. In the code, I use knockout.js to bind this array into the UI, which as you can see, requires very little code, instead using knockout’s data-bind attributes to bind server data to the UI. Of course, this is just one way to use the data – it’s entirely up to you to decide what to do with the data in your client code. Along the same lines, I can retrieve a single album to display when the user clicks on an album. The response returns the album information and a child array with all the songs. The code to do this is very similar to the last example where we pulled the albums array:$(".albumlink").live("click", function () { var id = $(this).data("id"); // title $.getJSON("albums/" + id, function (album) { ko.applyBindings(album, $("#divAlbumDialog")[0]); $("#divAlbumDialog").show(); }); }); Here the URL looks like this: /albums/Dirty%20Deeds, where the title is the ID captured from the clicked element’s data ID attribute. Explicitly Overriding Output Format When Web API automatically converts output using content negotiation, it does so by matching Accept header media types to the GlobalConfiguration.Configuration.Formatters and the SupportedMediaTypes of each individual formatter. You can add and remove formatters to globally affect what formats are available and it’s easy to create and plug in custom formatters.The example project includes a JSONP formatter that can be plugged in to provide JSONP support for requests that have a callback= querystring parameter. Adding, removing or replacing formatters is a global option you can use to manipulate content. It’s beyond the scope of this introduction to show how it works, but you can review the sample code or check out my blog entry on the subject (http://goo.gl/UAzaR). If automatic processing is not desirable in a particular Controller method, you can override the response output explicitly by returning an HttpResponseMessage instance. HttpResponseMessage is similar to ActionResult in ASP.NET MVC in that it’s a common way to return an abstract result message that contains content. HttpResponseMessage s parsed by the Web API framework using standard interfaces to retrieve the response data, status code, headers and so on[MS2] . Web API turns every response – including those Controller methods that return static results – into HttpResponseMessage instances. Explicitly returning an HttpResponseMessage instance gives you full control over the output and lets you mostly bypass WebAPI’s post-processing of the HTTP response on your behalf. HttpResponseMessage allows you to customize the response in great detail. Web API’s attention to detail in the HTTP spec really shows; many HTTP options are exposed as properties and enumerations with detailed IntelliSense comments. Even if you’re new to building REST-based interfaces, the API guides you in the right direction for returning valid responses and response codes. For example, assume that I always want to return JSON from the GetAlbums() controller method and ignore the default media type content negotiation. To do this, I can adjust the output format and headers as shown in Listing 4.public HttpResponseMessage GetAlbums() { var albums = AlbumData.Current.OrderBy(alb => alb.Artist); // Create a new HttpResponse with Json Formatter explicitly var resp = new HttpResponseMessage(HttpStatusCode.OK); resp.Content = new ObjectContent<IEnumerable<Album>>( albums, new JsonMediaTypeFormatter()); // Get Default Formatter based on Content Negotiation //var resp = Request.CreateResponse<IEnumerable<Album>>(HttpStatusCode.OK, albums); resp.Headers.ConnectionClose = true; resp.Headers.CacheControl = new CacheControlHeaderValue(); resp.Headers.CacheControl.Public = true; return resp; } This example returns the same IEnumerable<Album> value, but it wraps the response into an HttpResponseMessage so you can control the entire HTTP message result including the headers, formatter and status code. In Listing 4, I explicitly specify the formatter using the JsonMediaTypeFormatter to always force the content to JSON.  If you prefer to use the default content negotiation with HttpResponseMessage results, you can create the Response instance using the Request.CreateResponse method:var resp = Request.CreateResponse<IEnumerable<Album>>(HttpStatusCode.OK, albums); This provides you an HttpResponse object that's pre-configured with the default formatter based on Content Negotiation. Once you have an HttpResponse object you can easily control most HTTP aspects on this object. What's sweet here is that there are many more detailed properties on HttpResponse than the core ASP.NET Response object, with most options being explicitly configurable with enumerations that make it easy to pick the right headers and response codes from a list of valid codes. It makes HTTP features available much more discoverable even for non-hardcore REST/HTTP geeks. Non-Serialized Results The output returned doesn’t have to be a serialized value but can also be raw data, like strings, binary data or streams. You can use the HttpResponseMessage.Content object to set a number of common Content classes. Listing 5 shows how to return a binary image using the ByteArrayContent class from a Controller method. [HttpGet] public HttpResponseMessage AlbumArt(string title) { var album = AlbumData.Current.FirstOrDefault(abl => abl.AlbumName.StartsWith(title)); if (album == null) { var resp = Request.CreateResponse<ApiMessageError>( HttpStatusCode.NotFound, new ApiMessageError("Album not found")); return resp; } // kinda silly - we would normally serve this directly // but hey - it's a demo. var http = new WebClient(); var imageData = http.DownloadData(album.AlbumImageUrl); // create response and return var result = new HttpResponseMessage(HttpStatusCode.OK); result.Content = new ByteArrayContent(imageData); result.Content.Headers.ContentType = new MediaTypeHeaderValue("image/jpeg"); return result; } The image retrieval from Amazon is contrived, but it shows how to return binary data using ByteArrayContent. It also demonstrates that you can easily return multiple types of content from a single controller method, which is actually quite common. If an error occurs - such as a resource can’t be found or a validation error – you can return an error response to the client that’s very specific to the error. In GetAlbumArt(), if the album can’t be found, we want to return a 404 Not Found status (and realistically no error, as it’s an image). Note that if you are not using HTTP Verb-based routing or not accessing a method that starts with Get/Post etc., you have to specify one or more HTTP Verb attributes on the method explicitly. Here, I used the [HttpGet] attribute to serve the image. Another option to handle the error could be to return a fixed placeholder image if no album could be matched or the album doesn’t have an image. When returning an error code, you can also return a strongly typed response to the client. For example, you can set the 404 status code and also return a custom error object (ApiMessageError is a class I defined) like this:return Request.CreateResponse<ApiMessageError>( HttpStatusCode.NotFound, new ApiMessageError("Album not found") );   If the album can be found, the image will be returned. The image is downloaded into a byte[] array, and then assigned to the result’s Content property. I created a new ByteArrayContent instance and assigned the image’s bytes and the content type so that it displays properly in the browser. There are other content classes available: StringContent, StreamContent, ByteArrayContent, MultipartContent, and ObjectContent are at your disposal to return just about any kind of content. You can create your own Content classes if you frequently return custom types and handle the default formatter assignments that should be used to send the data out . Although HttpResponseMessage results require more code than returning a plain .NET value from a method, it allows much more control over the actual HTTP processing than automatic processing. It also makes it much easier to test your controller methods as you get a response object that you can check for specific status codes and output messages rather than just a result value. Routing Again Ok, let’s get back to the image example. Using the original routing we have setup using HTTP Verb routing there's no good way to serve the image. In order to return my album art image I’d like to use a URL like this: http://localhost/aspnetWebApi/albums/Dirty%20Deeds/image In order to create a URL like this, I have to create a new Controller because my earlier routes pointed to the AlbumApiController using HTTP Verb routing. HTTP Verb based routing is great for representing a single set of resources such as albums. You can map operations like add, delete, update and read easily using HTTP Verbs. But you cannot mix action based routing into a an HTTP Verb routing controller - you can only map HTTP Verbs and each method has to be unique based on parameter signature. You can't have multiple GET operations to methods with the same signature. So GetImage(string id) and GetAlbum(string title) are in conflict in an HTTP GET routing scenario. In fact, I was unable to make the above Image URL work with any combination of HTTP Verb plus Custom routing using the single Albums controller. There are number of ways around this, but all involve additional controllers.  Personally, I think it’s easier to use explicit Action routing and then add custom routes if you need to simplify your URLs further. So in order to accommodate some of the other examples, I created another controller – AlbumRpcApiController – to handle all requests that are explicitly routed via actions (/albums/rpc/AlbumArt) or are custom routed with explicit routes defined in the HttpConfiguration. I added the AlbumArt() method to this new AlbumRpcApiController class. For the image URL to work with the new AlbumRpcApiController, you need a custom route placed before the default route from Listing 1.RouteTable.Routes.MapHttpRoute( name: "AlbumRpcApiAction", routeTemplate: "albums/rpc/{action}/{title}", defaults: new { title = RouteParameter.Optional, controller = "AlbumRpcApi", action = "GetAblums" } ); Now I can use either of the following URLs to access the image: Custom route: (/albums/rpc/{title}/image)http://localhost/aspnetWebApi/albums/PowerAge/image Action route: (/albums/rpc/action/{title})http://localhost/aspnetWebAPI/albums/rpc/albumart/PowerAge Sending Data to the Server To send data to the server and add a new album, you can use an HTTP POST operation. Since I’m using HTTP Verb-based routing in the original AlbumApiController, I can implement a method called PostAlbum()to accept a new album from the client. Listing 6 shows the Web API code to add a new album.public HttpResponseMessage PostAlbum(Album album) { if (!this.ModelState.IsValid) { // my custom error class var error = new ApiMessageError() { message = "Model is invalid" }; // add errors into our client error model for client foreach (var prop in ModelState.Values) { var modelError = prop.Errors.FirstOrDefault(); if (!string.IsNullOrEmpty(modelError.ErrorMessage)) error.errors.Add(modelError.ErrorMessage); else error.errors.Add(modelError.Exception.Message); } return Request.CreateResponse<ApiMessageError>(HttpStatusCode.Conflict, error); } // update song id which isn't provided foreach (var song in album.Songs) song.AlbumId = album.Id; // see if album exists already var matchedAlbum = AlbumData.Current .SingleOrDefault(alb => alb.Id == album.Id || alb.AlbumName == album.AlbumName); if (matchedAlbum == null) AlbumData.Current.Add(album); else matchedAlbum = album; // return a string to show that the value got here var resp = Request.CreateResponse(HttpStatusCode.OK, string.Empty); resp.Content = new StringContent(album.AlbumName + " " + album.Entered.ToString(), Encoding.UTF8, "text/plain"); return resp; } The PostAlbum() method receives an album parameter, which is automatically deserialized from the POST buffer the client sent. The data passed from the client can be either XML or JSON. Web API automatically figures out what format it needs to deserialize based on the content type and binds the content to the album object. Web API uses model binding to bind the request content to the parameter(s) of controller methods. Like MVC you can check the model by looking at ModelState.IsValid. If it’s not valid, you can run through the ModelState.Values collection and check each binding for errors. Here I collect the error messages into a string array that gets passed back to the client via the result ApiErrorMessage object. When a binding error occurs, you’ll want to return an HTTP error response and it’s best to do that with an HttpResponseMessage result. In Listing 6, I used a custom error class that holds a message and an array of detailed error messages for each binding error. I used this object as the content to return to the client along with my Conflict HTTP Status Code response. If binding succeeds, the example returns a string with the name and date entered to demonstrate that you captured the data. Normally, a method like this should return a Boolean or no response at all (HttpStatusCode.NoConent). The sample uses a simple static list to hold albums, so once you’ve added the album using the Post operation, you can hit the /albums/ URL to see that the new album was added. The client jQuery code to call the POST operation from the client with jQuery is shown in Listing 7. var id = new Date().getTime().toString(); var album = { "Id": id, "AlbumName": "Power Age", "Artist": "AC/DC", "YearReleased": 1977, "Entered": "2002-03-11T18:24:43.5580794-10:00", "AlbumImageUrl": http://ecx.images-amazon.com/images/…, "AmazonUrl": http://www.amazon.com/…, "Songs": [ { "SongName": "Rock 'n Roll Damnation", "SongLength": 3.12}, { "SongName": "Downpayment Blues", "SongLength": 4.22 }, { "SongName": "Riff Raff", "SongLength": 2.42 } ] } $.ajax( { url: "albums/", type: "POST", contentType: "application/json", data: JSON.stringify(album), processData: false, beforeSend: function (xhr) { // not required since JSON is default output xhr.setRequestHeader("Accept", "application/json"); }, success: function (result) { // reload list of albums page.loadAlbums(); }, error: function (xhr, status, p3, p4) { var err = "Error"; if (xhr.responseText && xhr.responseText[0] == "{") err = JSON.parse(xhr.responseText).message; alert(err); } }); The code in Listing 7 creates an album object in JavaScript to match the structure of the .NET Album class. This object is passed to the $.ajax() function to send to the server as POST. The data is turned into JSON and the content type set to application/json so that the server knows what to convert when deserializing in the Album instance. The jQuery code hooks up success and failure events. Success returns the result data, which is a string that’s echoed back with an alert box. If an error occurs, jQuery returns the XHR instance and status code. You can check the XHR to see if a JSON object is embedded and if it is, you can extract it by de-serializing it and accessing the .message property. REST standards suggest that updates to existing resources should use PUT operations. REST standards aside, I’m not a big fan of separating out inserts and updates so I tend to have a single method that handles both. But if you want to follow REST suggestions, you can create a PUT method that handles updates by forwarding the PUT operation to the POST method:public HttpResponseMessage PutAlbum(Album album) { return PostAlbum(album); } To make the corresponding $.ajax() call, all you have to change from Listing 7 is the type: from POST to PUT. Model Binding with UrlEncoded POST Variables In the example in Listing 7 I used JSON objects to post a serialized object to a server method that accepted an strongly typed object with the same structure, which is a common way to send data to the server. However, Web API supports a number of different ways that data can be received by server methods. For example, another common way is to use plain UrlEncoded POST  values to send to the server. Web API supports Model Binding that works similar (but not the same) as MVC's model binding where POST variables are mapped to properties of object parameters of the target method. This is actually quite common for AJAX calls that want to avoid serialization and the potential requirement of a JSON parser on older browsers. For example, using jQUery you might use the $.post() method to send a new album to the server (albeit one without songs) using code like the following:$.post("albums/",{AlbumName: "Dirty Deeds", YearReleased: 1976 … },albumPostCallback); Although the code looks very similar to the client code we used before passing JSON, here the data passed is URL encoded values (AlbumName=Dirty+Deeds&YearReleased=1976 etc.). Web API then takes this POST data and maps each of the POST values to the properties of the Album object in the method's parameter. Although the client code is different the server can both handle the JSON object, or the UrlEncoded POST values. Dynamic Access to POST Data There are also a few options available to dynamically access POST data, if you know what type of data you're dealing with. If you have POST UrlEncoded values, you can dynamically using a FormsDataCollection:[HttpPost] public string PostAlbum(FormDataCollection form) { return string.Format("{0} - released {1}", form.Get("AlbumName"),form.Get("RearReleased")); } The FormDataCollection is a very simple object, that essentially provides the same functionality as Request.Form[] in ASP.NET. Request.Form[] still works if you're running hosted in an ASP.NET application. However as a general rule, while ASP.NET's functionality is always available when running Web API hosted inside of an  ASP.NET application, using the built in classes specific to Web API makes it possible to run Web API applications in a self hosted environment outside of ASP.NET. If your client is sending JSON to your server, and you don't want to map the JSON to a strongly typed object because you only want to retrieve a few simple values, you can also accept a JObject parameter in your API methods:[HttpPost] public string PostAlbum(JObject jsonData) { dynamic json = jsonData; JObject jalbum = json.Album; JObject juser = json.User; string token = json.UserToken; var album = jalbum.ToObject<Album>(); var user = juser.ToObject<User>(); return String.Format("{0} {1} {2}", album.AlbumName, user.Name, token); } There quite a few options available to you to receive data with Web API, which gives you more choices for the right tool for the job. Unfortunately one shortcoming of Web API is that POST data is always mapped to a single parameter. This means you can't pass multiple POST parameters to methods that receive POST data. It's possible to accept multiple parameters, but only one can map to the POST content - the others have to come from the query string or route values. I have a couple of Blog POSTs that explain what works and what doesn't here: Passing multiple POST parameters to Web API Controller Methods Mapping UrlEncoded POST Values in ASP.NET Web API   Handling Delete Operations Finally, to round out the server API code of the album example we've been discussin, here’s the DELETE verb controller method that allows removal of an album by its title:public HttpResponseMessage DeleteAlbum(string title) { var matchedAlbum = AlbumData.Current.Where(alb => alb.AlbumName == title) .SingleOrDefault(); if (matchedAlbum == null) return new HttpResponseMessage(HttpStatusCode.NotFound); AlbumData.Current.Remove(matchedAlbum); return new HttpResponseMessage(HttpStatusCode.NoContent); } To call this action method using jQuery, you can use:$(".removeimage").live("click", function () { var $el = $(this).parent(".album"); var txt = $el.find("a").text(); $.ajax({ url: "albums/" + encodeURIComponent(txt), type: "Delete", success: function (result) { $el.fadeOut().remove(); }, error: jqError }); }   Note the use of the DELETE verb in the $.ajax() call, which routes to DeleteAlbum on the server. DELETE is a non-content operation, so you supply a resource ID (the title) via route value or the querystring. Routing Conflicts In all requests with the exception of the AlbumArt image example shown so far, I used HTTP Verb routing that I set up in Listing 1. HTTP Verb Routing is a recommendation that is in line with typical REST access to HTTP resources. However, it takes quite a bit of effort to create REST-compliant API implementations based only on HTTP Verb routing only. You saw one example that didn’t really fit – the return of an image where I created a custom route albums/{title}/image that required creation of a second controller and a custom route to work. HTTP Verb routing to a controller does not mix with custom or action routing to the same controller because of the limited mapping of HTTP verbs imposed by HTTP Verb routing. To understand some of the problems with verb routing, let’s look at another example. Let’s say you create a GetSortableAlbums() method like this and add it to the original AlbumApiController accessed via HTTP Verb routing:[HttpGet] public IQueryable<Album> SortableAlbums() { var albums = AlbumData.Current; // generally should be done only on actual queryable results (EF etc.) // Done here because we're running with a static list but otherwise might be slow return albums.AsQueryable(); } If you compile this code and try to now access the /albums/ link, you get an error: Multiple Actions were found that match the request. HTTP Verb routing only allows access to one GET operation per parameter/route value match. If more than one method exists with the same parameter signature, it doesn’t work. As I mentioned earlier for the image display, the only solution to get this method to work is to throw it into another controller. Because I already set up the AlbumRpcApiController I can add the method there. First, I should rename the method to SortableAlbums() so I’m not using a Get prefix for the method. This also makes the action parameter look cleaner in the URL - it looks less like a method and more like a noun. I can then create a new route that handles direct-action mapping:RouteTable.Routes.MapHttpRoute( name: "AlbumRpcApiAction", routeTemplate: "albums/rpc/{action}/{title}", defaults: new { title = RouteParameter.Optional, controller = "AlbumRpcApi", action = "GetAblums" } ); As I am explicitly adding a route segment – rpc – into the route template, I can now reference explicit methods in the Web API controller using URLs like this: http://localhost/AspNetWebApi/rpc/SortableAlbums Error Handling I’ve already done some minimal error handling in the examples. For example in Listing 6, I detected some known-error scenarios like model validation failing or a resource not being found and returning an appropriate HttpResponseMessage result. But what happens if your code just blows up or causes an exception? If you have a controller method, like this:[HttpGet] public void ThrowException() { throw new UnauthorizedAccessException("Unauthorized Access Sucka"); } You can call it with this: http://localhost/AspNetWebApi/albums/rpc/ThrowException The default exception handling displays a 500-status response with the serialized exception on the local computer only. When you connect from a remote computer, Web API throws back a 500  HTTP Error with no data returned (IIS then adds its HTML error page). The behavior is configurable in the GlobalConfiguration:GlobalConfiguration .Configuration .IncludeErrorDetailPolicy = IncludeErrorDetailPolicy.Never; If you want more control over your error responses sent from code, you can throw explicit error responses yourself using HttpResponseException. When you throw an HttpResponseException the response parameter is used to generate the output for the Controller action. [HttpGet] public void ThrowError() { var resp = Request.CreateResponse<ApiMessageError>( HttpStatusCode.BadRequest, new ApiMessageError("Your code stinks!")); throw new HttpResponseException(resp); } Throwing an HttpResponseException stops the processing of the controller method and immediately returns the response you passed to the exception. Unlike other Exceptions fired inside of WebAPI, HttpResponseException bypasses the Exception Filters installed and instead just outputs the response you provide. In this case, the serialized ApiMessageError result string is returned in the default serialization format – XML or JSON. You can pass any content to HttpResponseMessage, which includes creating your own exception objects and consistently returning error messages to the client. Here’s a small helper method on the controller that you might use to send exception info back to the client consistently:private void ThrowSafeException(string message, HttpStatusCode statusCode = HttpStatusCode.BadRequest) { var errResponse = Request.CreateResponse<ApiMessageError>(statusCode, new ApiMessageError() { message = message }); throw new HttpResponseException(errResponse); } You can then use it to output any captured errors from code:[HttpGet] public void ThrowErrorSafe() { try { List<string> list = null; list.Add("Rick"); } catch (Exception ex) { ThrowSafeException(ex.Message); } }   Exception Filters Another more global solution is to create an Exception Filter. Filters in Web API provide the ability to pre- and post-process controller method operations. An exception filter looks at all exceptions fired and then optionally creates an HttpResponseMessage result. Listing 8 shows an example of a basic Exception filter implementation.public class UnhandledExceptionFilter : ExceptionFilterAttribute { public override void OnException(HttpActionExecutedContext context) { HttpStatusCode status = HttpStatusCode.InternalServerError; var exType = context.Exception.GetType(); if (exType == typeof(UnauthorizedAccessException)) status = HttpStatusCode.Unauthorized; else if (exType == typeof(ArgumentException)) status = HttpStatusCode.NotFound; var apiError = new ApiMessageError() { message = context.Exception.Message }; // create a new response and attach our ApiError object // which now gets returned on ANY exception result var errorResponse = context.Request.CreateResponse<ApiMessageError>(status, apiError); context.Response = errorResponse; base.OnException(context); } } Exception Filter Attributes can be assigned to an ApiController class like this:[UnhandledExceptionFilter] public class AlbumRpcApiController : ApiController or you can globally assign it to all controllers by adding it to the HTTP Configuration's Filters collection:GlobalConfiguration.Configuration.Filters.Add(new UnhandledExceptionFilter()); The latter is a great way to get global error trapping so that all errors (short of hard IIS errors and explicit HttpResponseException errors) return a valid error response that includes error information in the form of a known-error object. Using a filter like this allows you to throw an exception as you normally would and have your filter create a response in the appropriate output format that the client expects. For example, an AJAX application can on failure expect to see a JSON error result that corresponds to the real error that occurred rather than a 500 error along with HTML error page that IIS throws up. You can even create some custom exceptions so you can differentiate your own exceptions from unhandled system exceptions - you often don't want to display error information from 'unknown' exceptions as they may contain sensitive system information or info that's not generally useful to users of your application/site. This is just one example of how ASP.NET Web API is configurable and extensible. Exception filters are just one example of how you can plug-in into the Web API request flow to modify output. Many more hooks exist and I’ll take a closer look at extensibility in Part 2 of this article in the future. Summary Web API is a big improvement over previous Microsoft REST and AJAX toolkits. The key features to its usefulness are its ease of use with simple controller based logic, familiar MVC-style routing, low configuration impact, extensibility at all levels and tight attention to exposing and making HTTP semantics easily discoverable and easy to use. Although none of the concepts used in Web API are new or radical, Web API combines the best of previous platforms into a single framework that’s highly functional, easy to work with, and extensible to boot. I think that Microsoft has hit a home run with Web API. Related Resources Where does ASP.NET Web API fit? Sample Source Code on GitHub Passing multiple POST parameters to Web API Controller Methods Mapping UrlEncoded POST Values in ASP.NET Web API Creating a JSONP Formatter for ASP.NET Web API Removing the XML Formatter from ASP.NET Web API Applications© Rick Strahl, West Wind Technologies, 2005-2012Posted in Web Api   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

    Read the article

  • The Mysterious ARR Server Farm to URL Rewrite link

    - by OWScott
    Application Request Routing (ARR) is a reverse proxy plug-in for IIS7+ that does many things, including functioning as a load balancer.  For this post, I’m assuming that you already have an understanding of ARR.  Today I wanted to find out how the mysterious link between ARR and URL Rewrite is maintained.  Let me explain… ARR is unique in that it doesn’t work by itself.  It sits on top of IIS7 and uses URL Rewrite.  As a result, ARR depends on URL Rewrite to ‘catch’ the traffic and redirect it to an ARR Server Farm. As the last step of creating a new Server Farm, ARR will prompt you with the following: If you accept the prompt, it will create a URL Rewrite rule for you.  If you say ‘No’, then you’re on your own to create a URL Rewrite rule. When you say ‘Yes’, the Server Farm’s checkbox for “Use URL Rewrite to inspect incoming requests” will be checked.  See the following screenshot. However, I’m not a fan of this auto-rule.  The problem is that if I make any changes to the URL Rewrite rule, which I always do, and then make the wrong change in ARR, it will blow away my settings.  So, I prefer to create my own rule and manage it myself. Since I had some old rules that were managed by ARR, I wanted to update them so that they were no longer managed that way.  I took a look at a config in applicationHost.config to try to find out what property would bind the two together.  I assumed that there would be a property on the ServerFarm called something like urlRewriteRuleName that would serve as the link between ARR and URL Rewrite.  I found no such property.  After a bit of testing, I found that the name of the URL Rewrite rule is the only link between ARR and URL Rewrite.  I wouldn’t have guessed.  The URL Rewrite rule needs to be exactly ARR_{ServerFarm Name}_loadBalance, although it’s not case sensitive. Consider the following auto-created URL Rewrite rule: And, the link between ARR and URL Rewrite exists: Now, as soon as I rename that to anything else, for example, site.com ARR Binding, the link between ARR and URL Rewrite is broken. To be certain of the relationship, I renamed it back again and sure enough, the relationship was reestablished. Why is this important?  It’s only important if you want to decouple the relationship between ARR the URL Rewrite rule, but if you want to do so, the best way to do that is to rename the URL Rewrite rule.  If you uncheck the “Use URL Rewrite to inspect incoming requests” checkbox, it will delete your rule for you without prompting.  Conclusion The mysterious link between ARR and URL Rewrite only exists through the ARR Rule name.  If you want to break the link, simply rename the URL Rewrite rule.  It’s completely safe to do so, and, in my opinion, this is a rule that you should manage yourself anyway. 

    Read the article

  • PowerShell Control over Nikon D3000 Camera

    My wife got me a Nikon D3000 camera for Christmas last year, and Im loving it but still trying to wrap my head around some of its features.  For instance, when you plug it into a computer via USB, it doesnt show up as a drive like most cameras Ive used to, but rather it shows up as Computer\D3000.  After a bit of research, Ive learned that this is because it implements the MTP/PTP protocol, and thus doesnt actually let Windows mount the cameras storage as a drive letter.  Nikon describes the use of the MTP and PTP protocols in their cameras here. What Im really trying to do is gain access to the cameras file system via PowerShell.  Ive been using a very handy PowerShell script to pull pictures off of my cameras and organize them into folders by date.  Id love to be able to do the same thing with my Nikon D3000, but so far I havent been able to figure out how to get access to the files in PowerShell.  If you know, Id appreciate any links/tips you can provide.  All I could find is a shareware product called PTPdrive, which Im not prepared to shell out money for (yet).  (and yes you can do much the same thing with Windows 7s Import Pictures and Videos wizard, which is pretty good too) However, in my searching, I did find some really cool stuff you can do with PowerShell and one of these cameras, like actually taking pictures via PowerShell commands.  Credit for this goes to James ONeill and Mark Wilson.  Heres what I was able to do: Taking Pictures via PowerShell with D3000 First, connect your camera, turn it on, and launch PowerShell.  Execute the following commands to see what commands your device supports.  $dialog = New-Object -ComObject "WIA.CommonDialog" $device = $dialog.ShowSelectDevice() $device.Commands You should see something like this: Now, to take a picture, simply point your camera at something and then execute this command: $device.ExecuteCommand("{AF933CAC-ACAD-11D2-A093-00C04F72DC3C}") .csharpcode, .csharpcode pre { font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/ } .csharpcode pre { margin: 0em; } .csharpcode .rem { color: #008000; } .csharpcode .kwrd { color: #0000ff; } .csharpcode .str { color: #006080; } .csharpcode .op { color: #0000c0; } .csharpcode .preproc { color: #cc6633; } .csharpcode .asp { background-color: #ffff00; } .csharpcode .html { color: #800000; } .csharpcode .attr { color: #ff0000; } .csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em; } .csharpcode .lnum { color: #606060; } Imagine my surprise when this actually took a picture (with auto-focus): Imagine what you could do with a camera completely under the control of your computer  Time-lapse photography would be pretty simple, for instance, with a very simple loop that takes a picture and then sleeps for a minute (or whatever time period).  Hooked up to a laptop for portability (and an A/C power supply), this would be pretty trivial to implement.  I may have to give it a shot and report back. Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

    Read the article

  • Oracle Virtualization at Oracle OpenWorld 2012

    - by Chris Kawalek
    Mini-Series Entry 1 of 3: Hands-On Virtualization This is the first entry of a 3 part mini-series aimed at highlighting server and desktop virtualization at this year’s Oracle OpenWorld.  Oracle OpenWorld 2012 is fast approaching! If you are as excited as we are about the fascinating new Oracle virtualization content featured at Oracle OpenWorld 2012, you won’t want to miss this blog mini-series. We will be highlighting sessions that cover advances and innovations in our products, our product strategy and roadmap, and hands on labs for step-by-step instructions from our field and product experts. In the blog mini-series you will learn about: The Oracle Virtualization general keynote session Hands-on labs  Key Oracle server and desktop virtualization sessions In this entry, we will cover the Oracle Virtualization keynote session and the hands-on labs you won't want to miss. General Session: Oracle Virtualization Strategy and Roadmap Session ID: GEN8725 Oracle offers the industry’s most complete and integrated virtualization portfolio enabling organizations to realize benefits beyond simple consolidation as they transform their data centers into flexible cloud-based infrastructures. Join Oracle executives and experts to learn about Oracle’s desktop-to-data-center virtualization solutions, such as the OS, with built-in management integration at all layers that can help you virtualize and manage the complete computing environment, from physical servers to virtual servers and applications. This “don’t-miss” session offers details of the latest product updates and strategy; product roadmaps; integration with enterprise applications; and real-world examples of how Oracle server, desktop, and storage virtualization is benefiting customers. Here are our top picks for Hands-On Labs for Oracle OpenWorld 2012: Oracle Virtual Desktop Infrastructure Performance and Tablet Mobility Session ID: HOL9907 This hands-on lab demonstrates the performance (using an industry-standard load tester) and roaming capabilities of Oracle Virtual Desktop Infrastructure with Oracle’s Sun Ray Clients, Apple iPad and other clients. Deploying an IaaS Environment with Oracle VM: Hands-On Lab  Session ID: HOL9558 This hands-on lab takes you through the planning and deployment of an infrastructure as a service (IaaS) environment with Oracle VM as the foundation. It covers a range of topics, from planning storage capacity, LUN creation, network bandwidth planning, and best practices to designing and streamlining the environment for ease of management. Learn from deeply experienced field engineers and product experts. Virtualize and Deploy Oracle Applications in Minutes with Oracle VM: Hands-On Lab Session ID: HOL9559 This hands-on lab is for application architects or system administrators who will need to deploy and manage Oracle Applications. You’ll learn how Oracle VM Templates can turn you into a power user who can virtualize and deploy complex Oracle Applications in minutes. Longtime field-experienced engineers and product experts will show you, step by step, how to download and import templates and deploy the applications. x86 Enterprise Cloud Infrastructure with Oracle VM 3.x and Sun ZFS Storage Appliance Session ID: HOL9870 The purpose of this hands-on lab is to demonstrate the functionality and usage of Oracle’s enterprise cloud infrastructure for x86 with Oracle VM 3.x. It covers:  Creation of VMs Migration of VMs  Quick and easy deployment of Oracle applications with Oracle VM Templates  Usage of the Storage Connect plug-in for the Sun ZFS Storage Appliance You can find these and other great sessions on the Oracle OpenWorld 2012 Content Catalogue. Start checking now to better plan and organize your week at the conference. Then you’ll be ready to sign up for all of your sessions in mid-July when the scheduling tool goes live. While the hands-on labs allow you to directly interact with Oracle virtualization products, the conference sessions allow you to hear from a wide variety of industry experts on how they're using they technology in real world deployments, solving specific challenges, and more. In tomorrow's entry, we'll start talking about the many conference sessions related to Oracle server and desktop virtualization you can attend during the show. See you then! - The Oracle Virtualization marketing team

    Read the article

  • Updated Security Baseline (7u45) impacts Java 7u40 and before with High Security settings

    - by costlow
    The Java Security Baseline has been increased from 7u25 to 7u45.  For versions of Java below 7u45, this means unsigned Java applets or Java applets that depend on Javascript LiveConnect calls will be blocked when using the High Security setting in the Java Control Panel. This issue only affects Applets and Web Start applications. It does not affect other types of Java applications. The Short Answer Users upgrading to Java 7 update 45 will automatically fix this and is strongly recommended. The More Detailed Answer There are two items involved as described on the deployment flowchart: The Security Baseline – a dynamically updated attribute that checks to see which Java version contains the most recent security patches. The Security Slider – the user-controlled setting of when to prompt/run/block applets. The Security Baseline Java clients periodically check in to understand what version contains the most recent security patches. Versions are released in-between that contain bug fixes. For example: 7u25 (July 2013) was the previous secure baseline. 7u40 contained bug fixes. Because this did not contain security patches, users were not required to upgrade and were welcome to remain on 7u25. When 7u45 was released (October, 2013), this critical patch update contained security patches and raised the secure baseline. Users are required to upgrade from earlier versions. For users that are not regularly connected to the internet, there is a built in Expiration Date. Because of the pre-established quarterly critical patch updates, we are able to determine an approximate date of the next version. A critical patch released in July will have its successor released, at latest, in July + 3 months: October. The Security Slider The security slider is located within the Java control panel and determines which Applets & Web Start applications will prompt, which will run, and which will be blocked. One of the questions used to determine prompt/run/block is, “At or Above the Security Baseline.” The Combination JavaScript calls made from LiveConnect do not reside within signed JAR files, so they are considered to be unsigned code. This is correct within networked systems even if the domain uses HTTPS because signed JAR files represent signed "data at rest" whereas TLS (often called SSL) literally stands for "Transport Level Security" and secures the communication channel, not the contents/code within the channel. The resulting flow of users who click "update later" is: Is the browser plug-in registered and allowed to run? Yes. Does a rule exist for this RIA? No rules apply. Does the RIA have a valid signature? Yes and not revoked. Which security prompt is needed? JRE is below the baseline. This is because 7u45 is the baseline and the user, clicked "upgrade later." Under the default High setting, Unsigned code is set to "Don’t Run" so users see: Additional Notes End Users can control their own security slider within the control panel. System Administrators can customize the security slider during automated installations. As a reminder, in the future, Java 7u51 (January 2014) will block unsigned and self-signed Applets & Web Start applications by default.

    Read the article

  • Easily Add Facebook Chat to Pidgin

    - by Matthew Guay
    Want to keep in touch with your Facebook friends throughout the day?  Here we’ll show you how to easily add Facebook chat to the popular multi-protocol chat client Pidgin. Facebook has recently added support for XMPP chat, which means you can easily add it to popular chat clients such as Pidgin.  Previously you could only add Facebook chat to Pidgin through a plug-in that didn’t always work correctly.  Here we’ll walk you through setting up your Facebook account in Pidgin. Getting Started First, make sure you have a username for your Facebook account (link below).  This is a relatively new feature for Facebook, so if you’ve had your account for a while you may need to choose one.    If you already have one, you should see it listed instead. Now, open Pidgin, and click Manage Accounts. Click Add… Then select XMPP from the Protocol list. Now, enter your Facebook username without the facebook.com part (e.g your.facebook.username, not http://www.facebook.com/your.user.name).  Then, enter chat.facebook.com for the Domain, and enter your standard Facebook password.  You can check the “Remember password” box if you’d like Pidgin to automatically sign in to Facebook chat. Now, click on the Advanced tab, and uncheck the “Require SSL/TLS” box.  Also, make sure the Connect port is 5222.  Click Add, and your Facebook account is added to Pidgin. Now Facebook will show up in your list of accounts, with the username [email protected]. Your Facebook friends will show up directly in your Buddy list, complete with their full name and Facebook profile picture.  Any users that are not in a group will show under your standard list, while ones in a Facebook group will be shown in a separate group.  You can move which groups your Facebook friends show up in, just like you can with other chat contacts.   And no matter if your friend is logged in on the standard Facebook website or through another chat application, it will work the same as always.   This is a great way to keep in touch with your Facebook friends throughout the day.  If you like Facebook chat and already use Pidgin, now you can keep from switching between programs and just chat with all your friends from a central location. Links: Download Pidgin Set your Facebook username Similar Articles Productive Geek Tips The How-To Geek is No Longer on FacebookWin a Free iPod Touch in the How-To Geek Facebook Giveaway!Block Those Irritating Facebook Quiz & Application MessagesPut Your Pidgin Buddy List into the Windows Vista SidebarHow to Lock Down Your Facebook Account TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier Design Your Web Pages Using the Golden Ratio Worldwide Growth of the Internet How to Find Your Mac Address Use My TextTools to Edit and Organize Text

    Read the article

  • Best WordPress Shopping Cart & Ecommerce Plugins

    - by Edward
    A versatile WordPress Shopping Cart plugin can help you create a feature-rich online store on your WordPress-powered website or blog. Some are so advanced that you can get your store up and running in minutes. Some plugins allow you to take ecommerce to a next level with their high end customization tools. Here is a list of best WP shopping cart plugins available: Cart66 One of the best WordPress plugin with lots of features, great quality and ease of use. It accepts few more payment getways such as PayPal Website Payments Standard, PayPal Website Payments Professional, PayPal Express Checkout, eProcessing Network etc. It has flexible design options, recurring payments for subscriptions, memberships, and payment plans, Easy PCI Compliance – Safe and Secure. It is fast and efficient, one can sell digital and physical products and support is good. Price: Standard $49 & Professional $99 Details Download StorePress StorePress is a WordPress theme, which is fully coded. It comes with scripts that can change a WordPress blog into a veritable e-commerce virtual store. With this great premium WordPress theme, one can start affiliate stores, or promote affiliate products. Price: Single $59.99 & Developer License $119.99 Details Download WordPress eStore Plugin This shopping cart plugin comes with easy checkout, ease of design and use, automatic instant digital product delivery, Next Gen gallery integration, autoresponder integration etc. It is a lightweight shopping cart and allows multi site license. This plugin offers an amazingly comprehensive toolkit that will ensure your online shop is almost just plug-and-play. Price: $49.99 Details Download Shoppers Press Shoppers press is a premium cart for Word Press that comes with 20+ to choose from and 20+ built in payment gateways. It features one-click setups, personalized user accounts, easy management tools, detailed sales tracking, promotional options, a variety of product import tools, and many more features Price:$79 Details Download WordPress Shopping Cart plugin The WordPress Shopping Cart plugin by Tribulant quickly and seamlessly integrates an online shop with a fully functional shopping cart interface into any WordPress website. It has easy to use interface, which enables set up of multiple products and categorize and organizing them into multiple product categories. It also has many more attractive features. Price: $49.99 Details Download WP e-commerce WP e-commerce is a free full-featured shopping cart plugin for WordPress. It is a full featured shopping cart and boasts of easy checkout. It offers a wide range of features including SSL compatibility, customization and merchandising, integrated payment processing solutions including manual payment, Google Checkout and PayPal Payments, and email marketing. It is wordpress and social networking integrated. It is customizable by use of PHP template tag, wordpress shortcode and widgets. Details Download YAK for WordPress YAK is an open source shopping cart plugin for WordPress. It associates products with weblog entries (in other words, posts), so the post ID also becomes the product code. It supports both pages and posts as products, handles different types of product through categories. YAK supports downloadable products, so any e-books, plugins, or zip files you’re marketing can be easily purchased and dowloaded. Details Download Market Press It is another shopping cart full of many features. It offers following features such as assign categories and tags to products to make them easy to find, stock tracking with alerts, order management/alerts, fully customizable email messages, full support for most major currencies, fully customizable store urls/slugs, customers can checkout without being a site user etc. Expensive, but good option for those who can afford it. Price: $17.42/month Details Download Shopp It is an excellent shopping cart plugin for Word Press. This plugin is extremely easy to install and use. It has a cleaner interface. The customer support is good. Use can easily customize the look of the cart by using its amazing features. Price: $55 Details Download Related posts:8 PHP Shopping Cart Software for Reliable Ecommerce Solution Shopping Cart SEO 8 Free Open Source Shopping Carts

    Read the article

  • Integrate Google Docs with Outlook the Easy Way

    - by Matthew Guay
    Want to use Google Docs and Microsoft office together?  Here’s how you can use Harmony for Google Docs to integrates them seamlessly with Outlook. Harmony for Google Docs is an exciting new plugin for Outlook 2007 (a version for Outlook 2010 is in the works).  It lets you integrate your Google Docs account with Outlook via a sidebar.  From this, you can find any of your Google docs or upload a new document, and then you can open the document to view or edit it in Outlook. Getting Started Download Harmony for Google Docs (link below), and install as normal.  Make sure Outlook is closed before you run the install. Next time you open Outlook, the new Harmony sidebar will automatically open.  Enter your Google Account info, and click Sign In. Now, all of your Google Docs will show up in the sidebar. Double-click any file to open it in Outlook.  You may have to sign-in to Google Docs the first time you open a document. Here’s a Google Doc open in Outlook.  Notice that everything works, including full editing. All Google Docs features worked great in our tests except for the new drawings tool.  When we tried to insert a drawing, Outlook had a script error.  This was the only problem we had with Harmony, and could be due to an interaction between Google Drawings and Outlook’s rendering engine. Harmony makes it easy to find any file in your Google Docs account.  You can search for a file, or sort your files by type, recentness, and more. You can also easily add any document to Google Docs directly from Harmony.  You can drag and drop any document, including one attached to an email, to the Harmony sidebar, and it will directly upload to your Google Docs account. And, when you’re writing a new email or reply, click the Show Documents button to open the Harmony sidebar.  From here, you can add documents as usual and share it with email recipient. Conclusion We previously covered a similar app OffiSync which combines Google doc features with MS Office. However, Harmony makes it much easier to use Google Apps along with Outlook.  This gives you an easy and efficient way to collaborate on documents with coworkers, all without leaving Outlook.  And, if your company uses SharePoint instead of Google Docs, Harmony offers a SharePoint edition that integrates with Outlook just as easily! Link Download Harmony for Google Docs Similar Articles Productive Geek Tips How To Export Documents from Google Docs to Your ComputerView Your Google Calendar in Outlook 2007Sync Your Outlook and Google Calendar with Google Calendar SyncIntegrate Twitter With Microsoft OutlookSlacker Geek: Update Your Facebook Profile from Outlook TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Find That Elusive Icon with FindIcons Looking for Good Windows Media Player 12 Plug-ins? Find Out the Celebrity You Resemble With FaceDouble Whoa ! Use Printflush to Solve Printing Problems Icelandic Volcano Webcams

    Read the article

  • Collaborate10 &ndash; THEconference

    - by jean-pierre.dijcks
    After spending a few days in Mandalay Bay's THEHotel, I guess I now call everything THE... Seriously, they even tag their toilet paper with THEtp... I guess the brand builders in Vegas thought that once you are on to something you keep on doing it, and granted it is a nice hotel with nice rooms. THEanalytics Most of my collab10 experience was in a room called Reef C, where the BIWA bootcamp was held. Two solid days of BI, Warehousing and Analytics organized by the BIWA SIG at IOUG. Didn't get to see all sessions, but what struck me was the high interest in Analytics. Marty Gubar's OLAP session was full and he did some very nice things with the OLAP option. The cool bit was that he actually gets all the advanced calculations in OLAP to show up in OBI EE without any effort. It was nice to see that the idea from OWB where you generate an RPD is now also in AWM. I think it makes life so much simpler to generate these RPD's from your data model. Even if the end RPD needs some tweaking, it is all a lot less effort to get something going. You can see this stuff for yourself in this demo (click here). OBI EE uses just SQL to get to the calculations, and so, if you prefer APEX, you can build you application there and get the same nice calculations in an APEX application. Marty also showed the Simba MDX driver used with Excel. I guess we should call that THEcoolone... and it is very slick and wonderfully useful for all of you who actually know Excel. The nice thing is that you leverage pure Excel for all operations (no plug-ins). That means no new tools to learn, no new controls, all just pure Excel. THEdatabasemachine Got some very good questions in my "what makes Exadata fast" session and overall, the interest in Exadata is overwhelming. One of the things that I did try to do in my session is to get people to think in new patterns rather than in patterns based on Oracle 9i running on some random hardware configuration. We talked a little bit about the often over-indexing and how everyone has to unlearn all of that on Exadata. The main thing however is that everyone needs to get used to the shear size of some of the components in a Database machine V2. 5TB of flash cache is a lot of very fast data storage, half a TB of memory gets quite interesting as well. So what I did there was really focus on some of the content in these earlier posts on Upward ILM and In-Memory processing. In short, I do believe the these newer media point out a trend. In-memory and other fast media will get cheaper and will see more use. Some of that we do automatically by adding new functionality, but in some cases I think the end user of the system needs to start thinking about how to leverage all this new hardware. I think most people got very excited about these new capabilities and opportunities. THEcoolkids One of the cool things about the BIWA track was the hand-on track. Very cool to see big crowds for both OLAP and OWB hands-on. Also quite nice to see that the folks at RittmanMead spent so much time on preparing for that session. While all of them put down cool stuff, none was more cool that seeing Data Mining on an Apple iPAD... it all just looks great on an iPAD! Very disappointing to see that Mark Rittman still wasn't showing OWB on his iPAD ;-) THEend All in all this was a great set of sessions in the BIWA track. Lots of value to our guests (we hope) and we hope they all come again next year!

    Read the article

< Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >