Search Results

Search found 3018 results on 121 pages for 'plug in'.

Page 97/121 | < Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. Is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions?

  Read the article

• How to get data out of a Maxtor Shared Storage II that fails to boot?

  - by Jonik

  I've got a Maxtor Shared Storage II (RAID1 mode) which has developed some hardware failure, apparently: it fails to boot properly and is unreachable via network. When powering it on, it keeps making clunking/chirping disk noise and then sort of resets itself (with a flash of orange light in the usually-green LEDs); it then repeats this as if stuck in a loop. In fact, even the power button does nothing now – the only way I can affect the device at all is to plug in or pull out the power cord! (To be clear, I've come to regard this piece of garbage (which cost about 460 €) as my worst tech purchase ever. Even before this failure I had encountered many annoyances about the drive: 1) the software to manage it is rather crappy; 2) it is way noisier that what this type of device should be; 3) when your Mac comes out of sleep, Maxtor's "EasyManage" cannot re-mount the drive automatically.) Anyway, the question at hand is how to get my data out of it? As a very concrete first step, is there a way to open this thing without breaking the plastic casing into pieces? It is far from obvious to me how to get beyond this stage; it opens a little from one end but not from the other. If I somehow got the disks out, I could try mounting the disk(s) on one of the Macs or Linux boxes I have available (although I don't know yet if I'd need some adapters for that). (NB: for the purposes of this question, never mind any warranty or replacement issues – that's secondary to recovering the data.)

  Read the article

• Is there any way to force my Linux box to always boot up with a self-assigned IP address?

  - by Jeremy Friesner

  This is perhaps an unusual request: I'm trying to get a Debian Linux box to always give itself a self-assigned IP address (i.e. 169.254.x.y) on boot. In particular, I want it to do that even when there is a DHCP server present on the LAN. That is, it should not request an IP address from the DHCP server. From what I can see in the "man interfaces" text, there is an option for "manual", and an option for "dhcp". Manual assignment won't do, since I need multiple boxes to work on the same LAN without requiring any manual configuration... and "dhcp" does what I want, but only if there is no DHCP server on the LAN. (A requirement is that the functionality of these boxes should not be affected by the presence or absence of a DHCP server). Is there a trick that I can use to get this behavior? EDIT: By "no manual configuration", I mean that I should be able to take this box (headless) to any LAN anywhere, plug in the Ethernet cable, and have it do its thing. I shouldn't have to ssh to the box and edit files to get it working each time it is moved to a different LAN.

  Read the article

• Xbox Music ignores Asus FN media keys in Desktop Mode

  - by Ruud Lenders

  I have an Asus PRO64JQ laptop, and I recently upgraded to Windows 8. The FN keys stopped working, so I tried to install default drivers using the CD that came with my laptop. Unfortunately, the CD does not support Windows 8. Asus Support does not help me either. It seems that Asus does not support Windows 8 on my model, since I can't find it in their list of Windows 8 upgradable models. Also, the support page of my laptop does not allow me to select Windows 8 as OS. That's why I'm asking my question here. I fixed (most of) the FN keys by installing the ATKPackage, and I was happy to find out that the media keys (play/pauze, next, previous) works with the Xbox Music app. But the keys only work in the Metro UI. In Desktop Mode, pressing FN+? (play/pause) starts up Windows Media Player. Disabling Windows Media Player through the control panel stops it from popping up, but Xbox Music still only responds to them in the Metro UI. I remember that I had similar problems when I tried to make these media keys to work with iTunes on Windows 7. The fix there was a small iTunes plug-in. So tell me, do you know how to fix my problem? Thanks.

  Read the article

• I have a password protected USB drive with hidden partition, how to convert to normal USB drive?

  - by deddebme

  I have a generic USB drive which has password protection, and I want to stop this password protection mechanism and to use it as a normal 8GB USB drive. I received this USB drive as a gift in Hong Kong, and there was no instruction menu whatsoever, not even the manufacturer name. When I plug the drive in Windows XP, the removable drive comes up as a read only 5.28MB partition with two files. When I try to add or remove any files or formatting it, it will says the drive is write protected. After launching the Login.exe and typed in the password, a 8GB read/writeable partition will be shown, and I'm free to do anything to it. But once after the drive is unplugged and replugged, the same read only partition will still comes out no matter what I did to the hidden partition. Anyone knows about this kind if USB drive? What did the manufacturer do to hide the partition? Is there a way to "low-level" formatting this drive to convert (or revert) it to a normal drive? Before typing in the password: After typing in the password:

  Read the article

• Proper end of day sequence to maintain monitor config

  - by WarmBeer

  I've got an HP EliteBook 6930p that travels from home, where it is connected to individual cables, and work where there is a docking station. At both locations I have an external monitor as the secondary monitor and like to have the laptop screen as the primary, i.e. with the task bar. At the end of the day I close the laptop, which is supposed to set it to standby. When I get home I plug in the power cord and the external monitor cord and open the computer. When heading into work I close the computer and unplug everything. Inevitably when I open the computer at the new location the monitors are reversed, i.e. the primary, task bar display is on the external monitor and the laptop shows the secondary, even though when i click identify the laptop has the 1. I then have to disable the secondary display, switch the primary to the laptop and re-enable the secondary. I've tried locking the computer before closing and occasionally that works to keep the setup in place but not always. Any suggestions for how to keep the config in place during transport? ed

  Read the article

• Home Server: storage virtualisation, what to choose?

  - by Huygens

  I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on storage management. (I have another question related to the VM/compute instance management). Here my environement and wishes. Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) with 1 250GB system disk and up to 4 HDD (2 TB) for "data" OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine The 4 HDD is going to be a software RAID array, probably RAID 5. storage should be "virtualised/cloudified": easy to extend: if I add a NAS on the network, I can include the NAS space capacity within this storage space as one virtual disk. This can be a NAS, an external HDD or another server. cluster FS or S3 style space or OpenStack block storage? Whatever is easier to manage/maintain and easy to integrate/plug to VM/compute instance. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. Note: the VMs I intend to run on top of this server are one dedicated to backup, one for a "owncloud/dropbox"-like service and perhaps one for media server (hosting video and photos). I'm not sure if traditional VMs or compute instance are the most suitable for this.

  Read the article

• linux routing issue

  - by Duc To

  Hi! I have 2 linksys routers which has linux running on it and using tomato firmware.. both has internet lines plugged on but only 1 acts as DHCP server (router 1) What I am having to achieve is that all packets goes to router 1 from internal IPs want to access internet will go out to that internet line but from 1 specific port, if router 1 detects packets from a specific source port (for ex: http port: 80), it will redirect that packet to router 2 and goes out to the internet from there.. I have found some documents which give solution that I will need a linux servers with 2 ethernet cards and then we plug both internet lines on that server and routing base on it but I do not want to do that because my boss does not want to have an extra work mantaining that server, besides, he says that the router itself already a linux one so why.. I tend to agree his points.. Can it be done or a seperate linux server acting as a router is a must? Thank you all in advance and really look forward in your replies.. I am newbie to linux network and it seems to be something out of my capacity to solve :( Your sincerely! Duc To

  Read the article

• No sound out of headphone port on laptop

  - by Thanatos

  I cannot get sound out of the headphone port on a laptop. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller Some edits: Yes, the headphones are in all the way. This works in Windows: You plug headphones in, the internal speakers stop making noise, and noise comes out the head phones. Windows says I only have two sound cards: the HDMI port (which I don't care about) and the "sound card", which it claims is a "Conexant Pebble High Definition SmartAudio" In Windows, both the internal speakers and the headphone jack show up as one soundcard, which in my experience, is typical. (This is a laptop)

  Read the article

• USB question (how durable is it, how should I workaround this)

  - by Shiki

  The plot is quite simple. Got a Razer mouse. If I plug it in, it works. After a shutdown/hibernation, I have to replug it entirely at the back of the PC. (It works in my laptop even after severel shutdown, etc, so yes I guess it's my motherboard.. but it still got 2 years of warranty and it comes with quad SLI, its not an old motherboard at all. (MSI P7N SLI FI (bought it after a hungarian guy's recommendation)). So. I only could come up with one "solution". Get 3 USB cable (you know, USB-USB). If its possible the shortest ones (don't know if the responsibility/anything will worsen), AND replug only the middle+closest to the USB port junction, since those are replaceable. What do you think? Any other idea? (BIOS is updated, mouse driver ... doesn't really matter, the mouse won't even blink a bit after this happens. It lights up and goes totally dead.)

  Read the article

• Games, Windows 8.1 and 144Hz display

  - by Marioysikax

  So I have been having problems with few games after switching from 7 to 8.1, which seems to be related to my 144Hz monitor. Few examples: Shank, Shank 2, Blood of the Werewolf, Astebreed, the Sims 2 and Rayman Legends patch 1.2Had few other as well but it's been long and I have 600+ steam library. From those games at least the Sims 2 and Shank worked without any problems with same setup and Windows 7. So basically these games simply refuse to launch with basic setup. However if I plug 60Hz TV with HDMI instead everything magically starts to work. As for Astebreed and the Sims 2 using windowed mode seems to also work. As for Rayman Demo and version 1.0 works for some reason and 1.2 breaks settings menu. I have already tried contacting supports. EA support stated game simply shouldn't work with 8.1 at all (which is lie as it works with that TV and friend with 8 plays just fine), ubisoft support took few weeks and support said he will forward info for further processing, blood of the werewolf support had no idea what's going on and told me to just use my TV instead.Changing monitors refresh rate to 120Hz or forcing it to 60Hz doesn't do anything. I have DVI right now but I will try with DisplayPort when I get the cable. At PCGW Garrett said it may have something to do how listing resolutions work with 8 compared to earlier Windows versions but my googling skills don't bring anything up and compatibility mode for earlier windows version doesn't work either (not that I expected that to work). My system specs are on my steam profile. How do I get those work with my 144Hz monitor as well as possible future games having same problem? Downgrading to 7 would work but is far from practical and I don't own legit lisence for that one.

  Read the article

• How can I store logs and meet compliance requirements for free?

  - by Martin

  I am trying to keep long-term logs of an app in such a way, that it could plausibly demonstrated to third parties/court that the application has processed certain data at a given time. The data can be represented in XML or text format. A simple gzipped log is not plausible, as I may have added or modified data afterwards, whereas an external logging service would be an overkill. Cost is an issue, we are not dealing with financial data or so, but rather some simple user generated content, where some malicious users tried to blame the operator in the past when things escalated and went to court. My question: Is there some kind of signing software for Linux that signs each element of a log in such a way, that it can be easily shown that no element can be added or modified afterwards? Plug-Ins into some free Splunk Alternatives would be fine too. Ideally the software I am looking for should be under a GPL or similar license. I could probably achive something like this by using PGP/GPG sgning functions and including the previous elements signituares within the following element, but I would prefer to use some program where you do not have to argue about the validity of your own code. Note to mods: I am not asking this question on Stackoverflow, because I am not looking for writing own code for reasons described above. I think this question rather fits into serverfault than superuser, as server-side logging software is discussed rather here than on superuser.

  Read the article

• Completely unintuitive Apache/PHP memory-freeing behavior

  - by David

  Okay, this one's weird. I have a Turnkey Linux server with a gig of dedicated RAM. It's running WP3.2 with a boatload of plug-ins. It's a new site, so it has very limited traffic (other than search engines, maybe 20 hits a week). Now, for a few weeks, every few days, it would max out on main RAM, start eating up virtual RAM, and then crash. It's had this behavior for a while and I've been trying to figure out which element was causing the crash. Nine days ago, I pointed my external server monitor to this server. I wrote a 5-line HTML file (not PHP and not WP) that the server monitor accesses every minute, to see if the server is up. So, now, nine days later, the server has been rock solid, up all the time, no memory leak at all. I changed NOTHING on the server itself to see this behavior change. Have you EVER seen anything like this? All the server monitor is doing is retrieving a single, super-simple HTML file and all the memory leak problems have gone away. Weird, eh?

  Read the article

• Privacy, VPN and routers

  - by user123189

  Ever since this ACTA push-up the things are starting to heat up around torrents and privacy. I am using Tribler now, but this is not secure enough for me. Not enough privacy. I've been using in the past a swedish VPN PPTP connection. What I observed is that, when the VPN connection was down, Internet traffic wasn't cut off, rather the downloads were continuing, this time with my real IP, wearing off my protection. 1st : How to enforce a VPN connection that will cut all traffic when down? That is, the moment the connection is down, all internet traffic should cease as if I'd pull the network plug out. 2nd: Is PPTP good enough or should I ask for SSTP or IKEV2 ? 3rd: Should I disable IPv6 ? Is VPN no longer private if I keep IPv6 active? I 'heard some stuff' about dual vpn routers to be able to improve privacy; but nothing more about how to configure one for such a task. 4th: Is there any kind of "black box" hardware equipment that can be used in hiding IP, encrypting traffic and so on ?

  Read the article

• Switch to IPv6 and get rid of NAT? Are you kidding?

  - by Ernie

  So our ISP has set up IPv6 recently, and I've been studying what the transition should entail before jumping into the fray. I've noticed three very important issues: Our office NAT router (an old Linksys BEFSR41) does not support IPv6. Nor does any newer router, AFAICT. The book I'm reading about IPv6 tells me that it makes NAT "unnecessary" anyway. If we're supposed to just get rid of this router and plug everything directly to the Internet, I start to panic. There's no way in hell I'll put our billing database (With lots of credit card information!) on the internet for everyone to see. Even if I were to propose setting up Windows' firewall on it to allow only 6 addresses to have any access to it at all, I still break out in a cold sweat. I don't trust Windows, Windows' firewall, or the network at large enough to even be remotely comfortable with that. There's a few old hardware devices (ie, printers) that have absolutely no IPv6 capability at all. And likely a laundry list of security issues that date back to around 1998. And likely no way to actually patch them in any way. And no funding for new printers. I hear that IPv6 and IPSEC are supposed to make all this secure somehow, but without physically separated networks that make these devices invisible to the Internet, I really can't see how. I can likewise really see how any defences I create will be overrun in short order. I've been running servers on the Internet for years now and I'm quite familiar with the sort of things necessary to secure those, but putting something Private on the network like our billing database has always been completely out of the question. What should I be replacing NAT with, if we don't have physically separate networks?

  Read the article

• Two VGA monitors on Lenovo IdeaCentre H520 Desktop

  - by Sebastian-Laurentiu Plesciuc

  I recently bought a Lenovo IdeaCentre H520 computer and two VGA LED monitors. This particular PC has a dedicated NVIDIA Geforce GT630 video card and an integrated Intel HD Graphics 2500 video card. Both cards have VGA out. The Geforce card also has a HDMI out. I have installed Windows 8 and I can't seem to use both cards. I have connected both monitors, one to the VGA out of the Geforce card and one to the VGA out of the integrated card. I looked through the BIOS options for Video and I can only select the dedicated one, the integrate one or the Auto option. This kinda sucks. I was wondering what kind of options I have available. I have a VGA female to DVI A male adaptor, I was wondering if it could work if I can hook it to a DVI A female to HDMI male adaptor and plug one monitor into the VGA out of the Geforce video card and the other through both adapters to the HDMI out. Any chance this could work? I was looking online for a VGA to HDMI live cable but it's kind of expensive.

  Read the article

• Removing extended partition without deleting logical in it

  - by HisDudeness

  I'm running a Linux-based laptop, and in order to multi-boot several distros in it, I created an extended partition which contains a bunch of logical ones with GParted. Now, after quite a long time with this setup, I've changed my mind because of the consequent lack of storing space for my data partition. Now I want to keep one distro alone like it's normal, and eventually have some other operating systems stored in external supports to plug in and use if I want. Obviously, also this partition I want to keep (and to enlarge a little too) is just a logical inside the extended I want to keep. For what concerns the number I'm ok, meaning I currently have this big distro dedicated extended, the swap and the data partitions, so there's space for another primary before I delete the extended, but I don't know how to delete it without touching the logical in it, I don't want to reinstall the system losing all changes and settings, and I don't want to keep an extended partition for a logical alone. How can I do? Do I have to create a new primary, copy the logical content in it and then delete everything? Will the system boot and maintain exactly all the features it has now? Or is there a way to convert an extended into a primary once it contains just one logical? Or can I directly move a logical out of an extended turning it into a primary? Or, again, am I screwed?

  Read the article

• Set up Linux box as WAP for MyBookLive?

  - by AcidFlask

  I inherited an old Linux box as well as a MyBookLive and would like to make the MyBookLive available over my wireless, essentially using the Linux box as a wireless access point. I just wiped the Linux box (home) and installed Ubuntu 12.04 on it. My network setup currently looks like this: (192.168.0.1 netmask 255.255.255.0) ISP --- wireless router --- wlan0 on home (192.168.0.12) | eth0 on home --- MyBookLive MacBook (192.168.0.11) so that the MyBookLive is basically a glorified external hard drive. The router does have an Ethernet port, but it is being used by my roommate's computer so I can't plug the MyBookLive directly into it. Right now I can ping MyBookLive.local and MacBook.local from home, but I am having trouble understanding and figuring out what the correct iptables commands are to make my MacBook see my MyBookLive through the Bonjour network. Also, I'm not sure if I need to set up DNS to forward xxx.local Bonjour/Zeroconf addresses. I tried the following to forward my entire wired network (which has only my MyBookLive) to a single IP address: sysctl net.ipv4.ip_forward=1 iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT iptables -t nat -A PREROUTING -i eth0 -p tcp -j DNAT --to 192.168.0.66 iptables -t nat -A PREROUTING -i eth0 -p udp -j DNAT --to 192.168.0.66 but I can't ping this address from my MacBook. This is probably horribly wrong, but I am a complete noob at setting up this kind of network and could use some expert help with setting this up properly.

  Read the article

• Internet Troubles - PPPoE vs PPPoA?

  - by AkkA

  I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

  Read the article

• How do I share a complete XP disk so it can be seen from a Windows 7 system? (To move all files to a

  - by Ian Ringrose

  This should be easier! (both computers can see the internet etc so I know the network it’s self is working) I have a normal home network with a Windows XP machine on it and the new Windows 7 (64 bit) machine. So I can transfer the files to the new Windows 7 machine, I wish to share the complete disk (and all files) from the Windows XP machine and access them from the Windows 7 machine. Is there a step by step set of instructions for doing this anywhere? So fare I have: put both computers into the same workgroup put the windows 7 machine into work network mode so it can see the XP machine in the work group shared the XP disk as read only But when I try to access a lot of the folders on the XP disks, I am told I am not allowed to access them. (I was not asked for any passwords by the windows 7 machine when I accessed the XP machine. The XP machine just has its default account with no password set on it) The XP machine runs XP home and hence has "simple file shairing" turn on. So it seems that even if I create a admin account (with password) and connect with that account, it still comes in as "guest" on the XP machine. Chooseing to share the folder I want access to rather then the top of the disk drive seems to work, but is a pain as I need to share each user's folder with a different share name. If the new computer was not a laptop, I would just plug the hard disk from the old machine into it, but being a laptop I don't have that option.

  Read the article

• How to minimize the risk of employees spreading critical information?

  - by Industrial

  Hi everyone, What's common sense when it comes to minimising the risk of employees spreading critical information to rivalling companies? As of today, it's clear that not even the US government and military can be sure that their data stays safely within their doors. Thereby I understand that my question probably instead should be written as "What is common sense to make it harder for employees to spread business critical information?" If anyone would want to spread information, they will find a way. That's the way life work and always has. If we make the scenario a bit more realistic by narrowing our workforce by assuming we only have regular John Does onboard and not Linux-loving sysadmins , what should be good precautions to at least make it harder for the employees to send business-critical information to the competition? As far as I can tell, there's a few obvious solutions that clearly has both pros and cons: Block services such as Dropbox and similar, preventing anyone to send gigabytes of data through the wire. Ensure that only files below a set size can be sent as email (?) Setup VLANs between departments to make it harder for kleptomaniacs and curious people to snoop around. Plug all removable media units - CD/DVD, Floppy drives and USB Make sure that no configurations to hardware can be made (?) Monitor network traffic for non-linear events (how?) What is realistic to do in a real world? How does big companies handle this? Sure, we can take the former employer to court and sue, but by then the damage has already been caused... Thanks a lot

  Read the article

• Dell PowerEdge T710, add a new hard disk, how to?

  - by user1340802

  I need to add a new hard disk to a PowerEdge T710 running on Vmware EXSI 4. this hard disk is a 'normal' desktop hard disk 1TB (that is it is not coming from Dell, I also have no rack for it to plug it inside any of the front bay) I would like to add this disk for a virtual machine needing space, the most easily as possible. I have find that there is an avaiable sata cable with its electric power, so may I just add the disk plugging these and using the empty 5"1/4 slot available under the CD drive (with a 5"1/4 - 3"1/2 bay adaptater) ? (even if this way it seems that i bypass the raid controller that own the front bay with racks)) that way i think could be easier than adding the disk to the already defined Raid (btw i am also not sure on how to do these but i would not risk to mess the already working things) what are the other operations that i would have to do to ? (sorry I am a real beginner on Vmware EXSI and PowerEdge management :/ i have seen that there is some management from Bios (CTRL+R as start up) so that the disk will be seen or initialize it. I am really not sure of the steps needed...) thank you, best.

  Read the article

• How do I stop linux from trying to mount android phone as usb storage?

  - by user1160711

  When I plug in my Motorola Triumph to my fedora 17 linux box USB port, I get an endless series of errors on the linux box as it desperately attempts to mount the phone as a USB drive. Stuff like this: Jun 23 10:26:00 zooty kernel: [528926.714884] end_request: critical target error, dev sdg, sector 4 Jun 23 10:26:00 zooty kernel: [528926.715865] sd 16:0:0:1: [sdg] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jun 23 10:26:00 zooty kernel: [528926.715869] sd 16:0:0:1: [sdg] Sense Key : Illegal Request [current] Jun 23 10:26:00 zooty kernel: [528926.715872] sd 16:0:0:1: [sdg] Add. Sense: Invalid field in cdb Jun 23 10:26:00 zooty kernel: [528926.715876] sd 16:0:0:1: [sdg] CDB: Read(10): 28 20 00 00 00 00 00 00 04 00 If I go ahead and tell the phone to allow linux to mount the USB storage, the messages stop, and I get a mounted drive, but if all I want to do is use the debug bridge, my log on linux will continue to fill with this junk. Is there some udev magic I can do to make the system ignore this particular device as far as usb storage goes? I just noticed that if I tell the phone to enable USB storage, let linux recognize the new disk, then tell the phone to disable USB storage again, I get one additional log message about capacity changing to zero, but the endless spew of messages stops, so I guess one work around is to enable and disable USB right away.

  Read the article

• Are these three brand new sticks of RAM really dead?

  - by David Brown

  I'm working on a Dell Dimension 4700 desktop for a friend. It came with 512MB of DDR2 RAM (two sticks of 256MB). One morning, it started blue screening on startup with no helpful error messages. It refused to boot into any form of Windows installation, including Safe Mode, original recovery disk, and my custom Windows PE disk. It did boot into the Ultimate Boot CD, so I ran memtest86, which reported errors everywhere. I removed one stick of RAM and the system booted up just fine. I moved the remaining stick into each slot and the system continued to operate normally, so I came to the conclusion that the stick that I removed was dead. I ordered an exact replacement, along with 2 more sticks of 256MB DDR2 (again, exactly the same as the original), bringing the total system memory to 1GB. Upon installing the three brand new sticks, the system blue screened again, this time stating that win32k.sys attempted to write to read-only memory. I inserted my custom Windows PE disk in order to get a better look at the memory dump with BlueScreenView, but it refused to boot and produced another blue screen, but without an error message. I removed each new stick one-by-one, restarting each time. It continued to blue screen until I was left with only the original stick. I then tried inserting the new sticks in various different orders, but this only produced more blue screens. I reinserted all three sticks (along with the original) and ran memtest86 again, which reported errors all over the place. So, now I'm right back where I started. I don't think it could be the slots themselves, because I can plug the original stick into any slot and it works just fine. System setup reports each stick correctly and shows the total as 1GB, however. It just seems strange to me that all three brand new sticks of RAM could be dead on arrival. Is there something I missed? Or should I just go ahead and RMA them?

  Read the article

• Super slow opening my downloads folder

  - by Mark

  I have an exe file in my download folder that I half downloaded through utorrent (it's not piracy, a legit file from people who use bittorrent to distribute large files). I think I tried to open it while it was still sharing, that is, did not stop the upload. That actually froze my computer. When I restart in utorrent I set the file to be deleted. Unfortunately even though utorrent doesn't see that file anymore, it's still visible in my download folder. Whenever I try to open my download folder it literally takes 10 minutes or more. It opens, but is empty and the blue progress bar needs a long time to complete. After completion I can use the download folder normally, but opening and closing things in that folder takes a long time. I see the exe that I tried to download. I tried to delete it. But it was taking so long 30+ minutes that I eventually just hit cancel. That doesn't even work, and it was slowing down the computer. Couldn't figure out how to stop the delete so I just pulled the plug. Should I just forget about that dl folder and set a new one? Is there something I can do? Thanks.

  Read the article

< Previous Page | 93 94 95 96 97 98 99 100 101 102 103 104  | Next Page >