Search Results

Search found 3087 results on 124 pages for 'chi ping lee'.

Page 101/124 | < Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108 | Next Page >

Need Help Accessing the Vista Wampserver localhost from Virtual PC 2007 running an XP VM.

- by Reg

(I had posted this on stack overflow but it was suggested there that I post it here instead). I have a Vista laptop on which I'm running wampserver. I have Virtual PC 2007 setup with Windows XP running on the VM. My goal is to be able to use the XP VM to run IE6 to view the localhost in the Vista wampserver. I'm not interested in having the XP VM have any access to the internet -- only to my Vista wampserver's localhost. The vista wampserver works fine. As suggested on a blog I read, I installed the loopback adapter on Vista and I set the loopback to 192.168.21.1 and I set the xp vm ip to 192.168.21.2. I am able to successfully ping the vista-loopback adapter from the xp vm. I've turned the wampserver to "server online", and I've disabled the firewalls in both the vista host and the xp vm. But for some reason, I still can't seem to get the virtual XP to see the localhost on the vista wampserver. I've tried using the vista //name, and I've tried the ip 192.168.21.1 directly and with the port. For whatever its worth, I'm not able to see anything under the XM VM's network places (though I don't know if I'm supposed to be able to see anything). So at this point I'm stuck and I'm still not sure how to get this XP VM to "talk" to my vista wampserver localhost. Any advice on how to fix this problem is much appreciated. Thanks in advance for your help. -R

Read the article
DrayTek 2820 configuration using public IP addresses

- by Kev

I have a /29 range of public IP addresses assigned to me by my ISP. I'm trying to configure a SIP VOIP handset to register with my VOIP provider who recommend using public IP addresses rather than NAT. I have a DrayTek 2820 router flashed with the latest firmware and have configured my router as per DrayTek's FAQ at: How do I use a public subnet on the LAN (non-NAT operation ) ? My IP range is: xx.xx.94.16 -> xx.xx.94.23 This gives a usable range of: xx.xx.94.17 -> xx.xx.94.22 My router's public IP address is: xx.xx.94.17, the SIP VOIP handset is allocated xx.xx.94.18. I have a second internet connection and via that I can ping the handset. However for some reason I can't seem to get it to register with the provider. I tried adding a new Firewall filter to pass through from WAN to LAN: Source: ANY, Destination: xx.xx.94.18, UDP - Ports 1024 -> 65535 Out of interest I also tried opening port 80 to see if I could browse to the phone's admin web interface but no joy. I know that my ISP aren't blocking inbound service ports because I NAT Port Forwarded port 80 to one of my internal web servers and it rendered a test page I had set up. All the NAT settings are reset to factory defaults, i.e. there are no Port Redirection, DMZ Host, Open Ports or Address Mappings configured. The handset I'm using is a GrandStream GXP-2000. Is there anything else I should be doing?

Read the article
IPMI not fucntioning with Network Bonding

- by muhammed sameer

Hey, I am having problems with running IPMI on my servers that have network bonding enabled. Platform: CentOS release 5.3 (Final) Kernel: 2.6.18-92.el5 64bit Dell PowerEdge 1950 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet I have bonded the interface eth0 and eth1 as active passive, with eth0 as the active interface, below is conf description from /proc Bonding Mode: fault-tolerance (active-backup) Primary Slave: eth0 Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 30 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cd Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:22:19:56:b9:cf My IPMI device is as follows IPMI Device Information Interface Type: KCS (Keyboard Control Style) Specification Version: 2.0 I2C Slave Address: 0x10 NV Storage Device: Not Present Base Address: 0x0000000000000CA8 (I/O) Register Spacing: 32-bit Boundaries I Have used openIPMI as well as freeipmi both to control the chassis via the IPMI card, but on servers which have bonding enabled, the command times out, below is the full run of the command with debug info. ipmi_lan_send_cmd:opened=[0], open=[4482848] IPMI LAN host 70.87.28.115 port 623 Sending IPMI/RMCP presence ping packet ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed ipmi_lan_send_cmd:opened=[1], open=[4482848] No response from remote controller Get Auth Capabilities command failed Error: Unable to establish LAN session Failed to open LAN interface Unable to get Chassis Power Status On the other hand I configured IPMI on a box with the same specs as mentioned above without bonding and IPMI works perfectly. Has anyone faced this problem with IPMI + Bonding ? I would be thankful is someone helps circumvent this issue. Muhammed Sameer

Read the article
EC2 Ubuntu - Force instance to use internal IP

- by Peter

I've just set up a micro instance on EC2 (AMI ID ami-e59ca991). I had hoped to avoid charges for a year as my usage falls well within the bound of the free tier. I have been charged $0.01 for "regional data transfer". I read here that this is because my instance is talking to its self via it's external IP address. From what I've Googled it looks like you can stop the charges by making sure that the instance uses its internal IP address. However, when I ping the hostname of my instance internally (via an ssh session) it resolves to the instances internal IP address. How can I configure my instance so that I do not get these charges? Is it as simple as adding a line to my hosts file? Additionally, is this the real reason for the charge? I'm concerned that I've misunderstood the pricing somewhere. I have Apace and MySQL (with phpmyadmin) running on the machine - could I be being charged for data transfer associated with these (I have only one flat HTML page and I have only logged in via phpmyadmin - I have no data in my database). Edit: Additionally, my user account on MySQL was declared as: grant all privileges on *.* to 'peter'@'localhost'; Should I have instead used the internal hostname for the instance? grant all privileges on *.* to '[email protected]'; Cheers, Pete

Read the article
PXE boot and DHCP server configuration Failing Auto Installation

- by Harihara Vinayakaram

I have a ISC DHCP Server installed on Ubuntu 9.10 . I have managed to successfully boot a PXE client , obtain a DHCP address and load the initrd.gz file. But I am facing a vague problem when the debian installer starts up and tries to get a DHCP server The client send a DHCP request and I verified that is the same MAC Address. But I get a DHCP DECLINE (The client declines the address ). It offers all the address in the pool and then there is a DHCP NAK (no more free leases ) I tried using the Option no-ping, and also option one-client-one-lease but it does not help . If I set the client to use a fixed-address then the above problem is not there and the installation proceeds smoothly Can you give me any clues on what should be the DHCP server configuration My dhcpd.conf looks like this { ddns-update-style none; option domain-name "hadoop-myorg.org"; option domain-name-servers 192.168.3.5; default-lease-time 600; max-lease-time 7200; group { filename "pxelinux.0"; next-server 192.168.13.184; host hadoop1 { hardware ethernet 90:e6:ba:d5:53:f8; } } subnet 192.168.13.0 netmask 255.255.255.0 { option routers 10.0.0.254; pool { option domain-name-servers 192.168.3.5; max-lease-time 3000; range 192.168.13.55 192.168.13.65; deny unknown-clients; } } }

Read the article
./rtnet start rteth0-mac: unknown interface: No such device ioctl: No such device

- by Anisha Kaul

I have installed the RTnet over Xenomai. RTnet compiled well, and I also tested loopback on the single machine and was able to ping. However I noticed ./rtnet start showing the following output: What should I interpret when all it says is "no such device"? What more info should I provide here for you to help me in getting rid of this error? linux-y3pi:/usr/local/rtnet/sbin # ./rtnet start rteth0: unknown interface: No such device rteth0-mac: unknown interface: No such device ioctl: No such device ioctl: No such device ioctl: No such device ioctl: No such device ioctl (add): No such device vnic0: unknown interface: No such device SIOCSIFADDR: No such device vnic0: unknown interface: No such device SIOCSIFNETMASK: No such device Waiting for all slaves...ioctl: No such device ioctl: No such device linux-y3pi:/usr/local/rtnet/sbin # lsmod: linux-y3pi:/usr/local/rtnet/sbin # lsmod Module Size Used by tdma 18281 0 rtmac 9274 1 tdma rtcfg 49485 0 rtcap 7216 0 rt_loopback 1563 2 rtpacket 5517 0 rtudp 10655 0 rt_8139too 11374 0 rtipv4 22842 2 rtcfg,rtudp rtnet 42130 9 tdma,rtmac,rtcfg,rtcap,rt_loopback,rtpacket,rtudp,rt_8139too,rtipv4 ip6t_LOG 8480 6 xt_tcpudp 3540 2 xt_pkttype 1176 3 ipt_LOG 8201 6 xt_limit 2159 12 snd_pcm_oss 44878 0 snd_mixer_oss 15151 1 snd_pcm_oss snd_seq 55731 0 s nd_seq_device 6698 1 snd_seq edd 8407 0 ip6t_REJECT 4306 3 nf_conntrack_ipv6 8186 4 nf_defrag_ipv6 10128 1 nf_conntrack_ipv6 ip6table_raw 1451 1 xt_NOTRACK 1112 4 ipt_REJECT 2397 3 xt_state 1314 8 iptable_raw 1478 1 iptable_filter 1706 1 ip6table_mangle 1756 0 nf_conntrack_netbios_ns 1678 0 nf_conntrack_ipv4 8957 4 nf_conntrack 80411 5 nf_conntrack_ipv6,xt_NOTRACK,xt_state,nf_conntrack_netbios_ns,nf_conntrack_ipv4 nf_defrag_ipv4 1561 1 nf_conntrack_ipv4 ip_tables 18872 2 iptable_raw,iptable_filter ip6table_filter 1679 1 ip6_tables 19066 4 ip6t_LOG,ip6table_raw,ip6table_mangle,ip6table_filter x_tables 24094 16 ip6t_LOG,xt_tcpudp,xt_pkttype,ipt_LOG,xt_limit,ip6t_REJECT,ip6table_raw,xt_NOTRACK,ipt_REJECT,xt_state,iptable_raw,iptable_filter,ip6table_mangle,ip_tables,ip6table_filter,ip6_tables fuse 69279 3 loop 17417 0 dm_mod 71671 0 snd_hda_codec_via 57768 1 snd_hda_intel 24871 2 snd_hda_codec 95006 2 snd_hda_codec_via,snd_hda_intel snd_hwdep 6540 1 snd_hda_codec snd_pcm 90716 3 snd_pcm_oss,snd_hda_intel,snd_hda_codec snd_timer 22050 2 snd_seq,snd_pcm snd 71410 14 snd_pcm_oss,snd_mixer_oss,snd_seq,snd_seq_device,snd_hda_codec_via,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer soundcore 7854 1 snd iTCO_wdt 11716 0 iTCO_vendor_support 2942 1 iTCO_wdt snd_page_alloc 8324 2 snd_hda_intel,snd_pcm sr_mod 13186 0 cdrom 37628 1 sr_mod i2c_i801 9677 0 pcspkr 1950 0 sg 28847 0 serio_raw 4534 0 ext4 361361 2 jbd2 82943 1 ext4 crc16 1699 1 ext4 i915 500199 2 drm_kms_helper 33537 1 i915 drm 211193 3 i915,drm_kms_helper sd_mod 33977 5 i2c_algo_bit 5625 1 i915 intel_agp 11529 1 i915 intel_gtt 16397 3 i915,intel_agp ata_generic 3787 0 ata_piix 22875 4 ahci 20097 0 libahci 22089 1 ahci libata 194812 4 ata_generic,ata_piix,ahci,libahci scsi_mod 204709 4 sr_mod,sg,sd_mod,libata linux-y3pi:/usr/local/rtnet/sbin #

Read the article
rr.com appended to URL and I don't know why

- by Steph

I've been having some pretty bad and intermittent internet connectivity issues. I keep getting timeouts on my browsers, or what appears to be timeouts on my browsers. In Chrome it's generally error 21. FF it times out. And so on. While this is happening, I can go into the command line and ping or traceroute the same domain and it works fine. I use my cellphone on the same network and it's fine connecting to the same domain. And when it fails, it's all domains that are down in all browsers, chrome, FF, etc. I also noticed that when I try to connect to 192.168.1.1 it says in chrome did you mean www.192.168.1.1rr.com but when I enter https://192.168.1.1 it's fine. It only seems to do this in Chrome. This is making me think I have a virus. I did some researching about something called road runner, but I can't find any related traces. I also ran a full virus scan using nod32 (eset) and nothing. Any suggestion or help would be greatly appreciated. The intermittent loss of total internet access is really annoying and I'm worried about why it's trying to append the rr.com domain in Chrome. I suspect I'm dealing with two different issues, but you never know. Also for the DNS I'm using Google's DNS servers, the famous 8.8.8.8 and 8.8.8.4

Read the article
Web server with static IP from cable provider

- by Dmitri

I have a subscription to 5 static IP addresses. I want to run a web server from behind a router. My network config is as follows: Server's local address is 10.1.10.2, has IIS running on it, port 80 and 443 (IIS is not my fault, had to be done) the server's ip address is static, the subnet mask is 255.255.255.0, gateway is 10.1.10.1, which is the local address of the cable modem / router / gateway thingy. All looks to be in textbook order as far as the LAN goes. I can get to anything on my LAN from any computer on my LAN, whether they have static IP or get it through DHCP from the cable modem/router thingy. however, I have no internet access form any of my LAN computers. I called Comcast tech support and they say they can connect to my modem/router just fine and can actually use it to ping any computer on the internet or any computer on my LAN from the router/modem (i checked, myself, this is in fact the case). However, nothing on my LAN has internet connectivity. I tried pinging the DNS servers, nothing. I tried directly typing in web sites' IP addresses, nothing, so doesn't seem to be a DNS issue. Any Ideas? What malfunction of a router could be causing such weird behavior? nay ideas or educated guesses are very much appreciated.

Read the article
Cannot connect to local network shares when connected to VPN. Error: "the user name could not be found"

- by Nick G

I keep finding that on our small company LAN (7 users, 3 servers) that some servers keep becoming "not accessible" for the purposes of file sharing. They display the message "\SERVER is not accessible. You might not have permission to use this network resource. The user name could not be found". But I don't know why "the user name could not be found" as all the machines are on the same domain and the PDC and BDC seem to be behaving OK. EDIT: VPN seems to be the cause: It turns out I can see the server if I use the IP address (\\1.2.3.4\ etc) or the FQ active directory name (eg \server.domainname.local) but not if I use the server name on its own or a mapped network drive originally created from the "short" name. Oddly though, my machine has no issue resolving the server's DNS name as I can ping the machine name OK and it immediately comes back with the IP, however nslookup seems to fail. It seems to be a problem with how Windows looks up machine names when connected to VPNs. When I'm connected to a VPN, windows seems to use the DNS assocated with the VPN and not the one on the domain controller. This behavior to me, seems incorrect as surely that would mean connecting to any VPN would break any ability to lookup local machine names for servers and printers etc. So I guess the real question now is, how can I make my machine still search the local Active Directory DNS (the PDC) even when connected to a VPN? More info in my comments below.

Read the article
Phpmyadmin location for nginx

- by multiformeinggno

I installed nginx and phpmyadmin. I set up a domain with these parameters to test phpmyadmin: server { listen 80; server_name domain.com; root /usr/share/phpmyadmin; index index.php; fastcgi_index index.php; location ~ \.php$ { include /etc/nginx/fastcgi.conf; fastcgi_param SCRIPT_FILENAME /usr/share/phpmyadmin$fastcgi_script_name; fastcgi_pass unix:/var/run/php5-fpm.sock; } } And everything works properly (if I visit the domain I can login to phpmyadmin). The problem is that it was just for testing phpmyadmin, now I'd like to move this to my 'default' site. But I can't figure out how to have it on /phpmyadmin. Here's the config for the 'default' nginx site (where I'd like to put this /phpmyadmin location): server { server_name blabla; access_log /var/log/nginx/$host.access.log; error_log /var/log/nginx/error.log; root /var/www/default; index index.php index.html; location / { try_files $uri $uri/ index.php; } location ~ \.php$ { include /etc/nginx/fastcgi.conf; fastcgi_pass unix:/var/run/php5-fpm.sock; } ### NginX Status location /nginx_status { stub_status on; access_log off; } ### FPM Status location ~ ^/(status|ping)$ { fastcgi_pass unix:/var/run/php5-fpm.sock; access_log off; } }

Read the article
Website does not resolve in browser but traceroute is successful

- by Colum

I am trying to figure out an issue. My internet is working fine, but this one website is not resolving. It works via a proxy, traceroute works: 1 192.168.1.1 (192.168.1.1) 4.205 ms 0.568 ms 0.510 ms 2 * * * 3 67.59.255.13 (67.59.255.13) 10.583 ms 7.949 ms 7.557 ms 4 67.59.255.61 (67.59.255.61) 10.256 ms 9.576 ms 13.083 ms 5 64.15.8.126 (64.15.8.126) 9.943 ms 11.929 ms 11.452 ms 6 64.15.0.217 (64.15.0.217) 14.655 ms 14.092 ms 13.771 ms 7 64.15.0.118 (64.15.0.118) 33.201 ms 34.875 ms 36.544 ms 8 xe-6-0-3.ar1.ord1.us.nlayer.net (69.31.111.169) 34.027 ms 34.957 ms 34.231 ms 9 ae1-30g.cr1.ord1.us.nlayer.net (69.31.111.133) 82.683 ms 35.138 ms 37.592 ms 10 xe-3-0-0.cr2.iad1.us.nlayer.net (69.22.142.26) 41.657 ms 34.063 ms 34.519 ms 11 ae2-30g.ar2.iad1.us.nlayer.net (69.31.31.186) 35.780 ms 36.361 ms 33.968 ms 12 as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 35.086 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.234) 38.031 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 36.833 ms 13 cr1.iad2.inforelay.net (66.231.176.246) 32.595 ms cr2.iad1.inforelay.net (66.231.176.10) 31.771 ms cr1.iad2.inforelay.net (66.231.176.246) 32.622 ms 14 cr1.iad2.inforelay.net (66.231.176.246) 32.956 ms 33.625 ms !X 41.058 ms 15 * cr1.iad2.inforelay.net (66.231.176.246) 35.312 ms !X * 16 * cr1.iad2.inforelay.net (66.231.176.246) 32.814 ms !X * 17 cr1.iad2.inforelay.net (66.231.176.246) 35.459 ms !X * 53.137 ms !X Ping returns this: Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 Request timeout for icmp_seq 3 Request timeout for icmp_seq 4 Request timeout for icmp_seq 5 Request timeout for icmp_seq 6 But what I can not figure out is why my browsers (Firefox, Safari, Opera) can not resolve the domain. I am on a Wifi connection. What could be the problem? BTW I am on a Mac (10.6.5)

Read the article
Website does not resolve in browser but traceroute is successful

- by Colum

I am trying to figure out an issue. My internet is working fine, but this one website is not resolving. It works via a proxy, traceroute works: 1 192.168.1.1 (192.168.1.1) 4.205 ms 0.568 ms 0.510 ms 2 * * * 3 67.59.255.13 (67.59.255.13) 10.583 ms 7.949 ms 7.557 ms 4 67.59.255.61 (67.59.255.61) 10.256 ms 9.576 ms 13.083 ms 5 64.15.8.126 (64.15.8.126) 9.943 ms 11.929 ms 11.452 ms 6 64.15.0.217 (64.15.0.217) 14.655 ms 14.092 ms 13.771 ms 7 64.15.0.118 (64.15.0.118) 33.201 ms 34.875 ms 36.544 ms 8 xe-6-0-3.ar1.ord1.us.nlayer.net (69.31.111.169) 34.027 ms 34.957 ms 34.231 ms 9 ae1-30g.cr1.ord1.us.nlayer.net (69.31.111.133) 82.683 ms 35.138 ms 37.592 ms 10 xe-3-0-0.cr2.iad1.us.nlayer.net (69.22.142.26) 41.657 ms 34.063 ms 34.519 ms 11 ae2-30g.ar2.iad1.us.nlayer.net (69.31.31.186) 35.780 ms 36.361 ms 33.968 ms 12 as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 35.086 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.234) 38.031 ms as33597.xe-3-0-7.ar2.iad1.us.nlayer.net (69.31.30.230) 36.833 ms 13 cr1.iad2.inforelay.net (66.231.176.246) 32.595 ms cr2.iad1.inforelay.net (66.231.176.10) 31.771 ms cr1.iad2.inforelay.net (66.231.176.246) 32.622 ms 14 cr1.iad2.inforelay.net (66.231.176.246) 32.956 ms 33.625 ms !X 41.058 ms 15 * cr1.iad2.inforelay.net (66.231.176.246) 35.312 ms !X * 16 * cr1.iad2.inforelay.net (66.231.176.246) 32.814 ms !X * 17 cr1.iad2.inforelay.net (66.231.176.246) 35.459 ms !X * 53.137 ms !X Ping returns this: Request timeout for icmp_seq 0 Request timeout for icmp_seq 1 Request timeout for icmp_seq 2 Request timeout for icmp_seq 3 Request timeout for icmp_seq 4 Request timeout for icmp_seq 5 Request timeout for icmp_seq 6 But what I can not figure out is why my browsers (Firefox, Safari, Opera) can not resolve the domain. I am on a Wifi connection. What could be the problem? BTW I am on a Mac (10.6.5)

Read the article
Openfiler iSCSI performance

- by Justin

Hoping someone can point me in the right direction with some iSCSI performance issues I'm having. I'm running Openfiler 2.99 on an older ProLiant DL360 G5. Dual Xeon processor, 6GB ECC RAM, Intel Gigabit Server NIC, SAS controller with and 3 10K SAS drives in a RAID 5. When I run a simple write test from the box directly the performance is very good: [root@localhost ~]# dd if=/dev/zero of=tmpfile bs=1M count=1000 1000+0 records in 1000+0 records out 1048576000 bytes (1.0 GB) copied, 4.64468 s, 226 MB/s So I created a LUN, attached it to another box I have running ESXi 5.1 (Core i7 2600k, 16GB RAM, Intel Gigabit Server NIC) and created a new datastore. Once I created the datastore I was able to create and start a VM running CentOS with 2GB of RAM and 16GB of disk space. The OS installed fine and I'm able to use it but when I ran the same test inside the VM I get dramatically different results: [root@localhost ~]# dd if=/dev/zero of=tmpfile bs=1M count=1000 1000+0 records in 1000+0 records out 1048576000 bytes (1.0 GB) copied, 26.8786 s, 39.0 MB/s [root@localhost ~]# Both servers have brand new Intel Server NIC's and I have Jumbo Frames enabled on the switch, the openfiler box as well as the VMKernel adapter on the ESXi box. I can confirm this is set up properly by using the vmkping command from the ESXi host: ~ # vmkping 10.0.0.1 -s 9000 PING 10.0.0.1 (10.0.0.1): 9000 data bytes 9008 bytes from 10.0.0.1: icmp_seq=0 ttl=64 time=0.533 ms 9008 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=0.736 ms 9008 bytes from 10.0.0.1: icmp_seq=2 ttl=64 time=0.570 ms The only thing I haven't tried as far as networking goes is bonding two interfaces together. I'm open to trying that down the road but for now I am trying to keep things simple. I know this is a pretty modest setup and I'm not expecting top notch performance but I would like to see 90-100MB/s. Any ideas?

Read the article
When I restart my virtual enviorment it does not re-bind to the IP address

- by RoboTamer

The IP does no longer respond to a remote ping With restart I mean: lxc-stop -n vm3 lxc-start -n vm3 -f /etc/lxc/vm3.conf -d -- /etc/network/interfaces auto lo iface lo inet loopback up route add -net 127.0.0.0 netmask 255.0.0.0 dev lo down route add -net 127.0.0.0 netmask 255.0.0.0 dev lo # device: eth0 auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.22.189.58 netmask 255.255.255.248 gateway 192.22.189.57 broadcast 192.22.189.63 bridge_ports eth0 bridge_fd 0 bridge_hello 2 bridge_maxage 12 bridge_stp off post-up ip route add 192.22.189.59 dev br0 post-up ip route add 192.22.189.60 dev br0 post-up ip route add 192.22.189.61 dev br0 post-up ip route add 192.22.189.62 dev br0 -- /etc/lxc/vm3.conf lxc.utsname = vm3 lxc.rootfs = /var/lib/lxc/vm3/rootfs lxc.tty = 4 #lxc.pts = 1024 # pseudo tty instance for strict isolation lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.mtu = 1500 #lxc.cgroup.cpuset.cpus = 0 # security parameter lxc.cgroup.devices.deny = a # Deny all access to devices lxc.cgroup.devices.allow = c 1:3 rwm # dev/null lxc.cgroup.devices.allow = c 1:5 rwm # dev/zero lxc.cgroup.devices.allow = c 5:1 rwm # dev/console lxc.cgroup.devices.allow = c 5:0 rwm # dev/tty lxc.cgroup.devices.allow = c 4:0 rwm # dev/tty0 lxc.cgroup.devices.allow = c 4:1 rwm # dev/tty1 lxc.cgroup.devices.allow = c 4:2 rwm # dev/tty2 lxc.cgroup.devices.allow = c 1:9 rwm # dev/urandon lxc.cgroup.devices.allow = c 1:8 rwm # dev/random lxc.cgroup.devices.allow = c 136:* rwm # dev/pts/* lxc.cgroup.devices.allow = c 5:2 rwm # dev/pts/ptmx lxc.cgroup.devices.allow = c 254:0 rwm # rtc # mounts point lxc.mount.entry=proc /var/lib/lxc/vm3/rootfs/proc proc nodev,noexec,nosuid 0 0 lxc.mount.entry=devpts /var/lib/lxc/vm3/rootfs/dev/pts devpts defaults 0 0 lxc.mount.entry=sysfs /var/lib/lxc/vm3/rootfs/sys sysfs defaults 0 0

Read the article
Cisco SG200 vlan issue in ESXi VSA cluster

- by George

I have three Cisco SG200-26 switches, and I also have two ESXi hosts that I have connected like shown in the below "best practice" map by VMware: http://communities.vmware.com/servlet/JiveServlet/previewBody/17393-102-1-22458/VSA_networking_map.pdf Even though I created the VLANs in the SG200 and I set the two VLANs (508 and 608) as allowed for these untagged ports (where my ESX NIC's are connected), I can not ping from host 1 to host 2 when configuring the NIC's to use 608 VLAN. Am I missing something? my IP's are all in the 192.168. range, and the only reason I need the VLANs is to isolate the traffic of VSA back-end internally, only the two hosts will be using the VLANs. So I think I do not have to create virtual interfaces on my router since that's the case, is my understanding correct? Also sending my switch config screenshot below.. all 3 switches have the latest firmware (it seems these were originally linksys and got rebranded as cisco after the acquisition) http://img31.imageshack.us/img31/2503/switch.gif Any ideas what to change on the Cisco SG200 to make this work , would be appreciated! The second VLAN (608) only needs two IP's: 192.168.0.1 and 192.168.0.2 The first VLAN (508) will have about 15 IP's for ESXi Management and VSA cluster service, I could use either 192.168.1.xx or 10.0.1.xx The rest of my network (about 50 clients) is in 192.168.1.xx range VMware also states that the VLAN protocol on the physical switch must be 802.1Q, not ISL, anyone knows which of the two my SG200-26 uses? In addition to that, the only requirement from VSA is that my two hosts: -Are in the same subnet. -Have static IP addresses set. -Have the same Default Gateway configured. If I need inter-vlan routing for this, I suppose I have to create virtual interfaces on my sonicwall, and assign an IP for each VLAN, and then set routes between them? Thank you for your time!

Read the article
Wifi Drops Connections with WPA2-PSK

- by graf_ignotiev

I run a small computer lab made up of 10 computers of identical hardware and software (Dell Latitudes with Windows 7 x64 Enterprise) and I use a ZyWALL 2WG as a router/firewall. Nine of the computers connect to the router over wifi using WPA2-PSK encryption while the last one is connected by ethernet cable. I'm having a problem where any computer connected to the wi-fi occasionally drops off the network (it cannot be pinged and the client cannot ping the gateway). It only happens on the wifi side and only when the encryption is WPA2-PSK or WPA-PSK. I tried using another router with a different make and model and had no problems. Thinking it could be a software error, I reset the router to factory defaults and installed the newest firmware (V4.04(AQI.8) | 04/09/2010), but still have the problem. The 802.1X log gives the following error User logout because of user disassociation. with this note WPA2-PSK:00242c582ece:logout where 00242c582ece is the mac address of the device. At this point I'm out of things to try and leads to follow. It looks like this user had the same or similar problem, but none of those proposed solutions work for me.

Read the article
Using virtual IP with stunnel and haproxy

- by beardtwizzle

Hi there, We have a load-balancer setup, in which an HTTPS Request flows through the following steps:- Client -> DNS -> stunnel on Load-Balancer -> HAProxy on LB -> Web-Server This setup works perfectly when stunnel is listening to the local IP of the Load-Balancer. However in our setup we have 2 load-balancers and we want to be able to listen to a virtual IP, which only ever exists on one LB at a time (keepalived flips the IP to the second LB if the first one falls over). HAProxy has no problem in doing this (and I can ping the assigned virtual IP on the load-balancer I'm testing), but it seems stunnel hates the concept. Has anyone achieved this before (below is my stunnel config - as you can see I'm actually listening for ALL traffic on 443):- cert= /etc/ssl/certs/mycert.crt key = /etc/ssl/certs/mykey.key ;setuid = nobody ;setgid = nogroup pid = /etc/stunnel/stunnel.pid debug = 3 output = /etc/stunnel/stunnel.log socket=l:TCP_NODELAY=1 socket=r:TCP_NODELAY=1 [https] accept=443 connect=127.0.0.1:8443 TIMEOUTclose=0 xforwardedfor=yes Sorry for the long-winded question!

Read the article
DD-WRT PPTP VPN problem

- by Tobias Tromm

I try to configure a DD-WRT as a PPTP client. The VPN Server is Windows Server 2003. This is my scenario: The Windows 2003 Server has set to give to the VPN Client the 10.0.0.81 fixed IP and to add a network route to the remote home. At the remote home I have changed the PPTP Options at DD-WRT to make the connection. The VPN connection is successfully established. ...and Windows successfully add the route to the remote home 192.168.2.X. From the remote home I can successfully access any computer from the VPN server side. The problem is when I try to access the remote home from the Server side. From Server side I only can access\ping DD-WRT ( by VPN Client IP - 10.0.0.81). What's wrong? How I need to do to be a site-to-site VPN? This is what happen when I try to tracert the remote home from local home.

Read the article
SQL Server 2008 cluster freezing

- by Ed Leighton-Dick

We have run into a strange situation in which a SQL Server 2008 single-node cluster hangs. As background, we are rebuilding a Windows Server 2003/SQL Server 2005 two-node cluster using Windows 2008 and SQL Server 2008. Here's the timeline: Evicted the passive node (server B) from the Windows 2003/SQL 2005 cluster. The active node now functions as a single-node cluster with no problems. Wiped server B's disks and installed Windows 2008 and SQL Server 2008 as a single-node cluster. Since we do not want to the two clusters to communicate yet, we left the cluster's private network "heartbeat" adapter unconfigured. The cluster comes up and functions normally. Moved all databases to the new cluster. Cluster continues to function normally. Turned off server A (old cluster) in preparation for rebuilding as the second node of the new cluster. SQL Server instance on server B (new cluster) locks up, even though it should have no knowledge of or interaction with server A. Restarted server A. SQL Server instance on server B (new cluster) immediately begins working again. Things we have tried: The new cluster's name responds to ping and NETBIOS requests, even while the SQL Server is hung. We have confirmed that no IP address is assigned to the old heartbeat adapter, and it is not pulling an IP address from DHCP. Disabling the heartbeat's network card has the same effect. No errors were generated in any logs - Windows or SQL. When the error first occurred, it sat in the hung state for quite some time (well over 10 minutes) before anyone figured out what was going on. This would seem to eliminate any sort of normal cluster timeout in which it would have been searching for the other node (even if one had been configured). Server B is running Windows 2008 SP2, fully patched, and SQL Server 2008 SP1 CU7 (10.0.2775).

Read the article
Can't make virtual host working

- by sica07

I have to create a virtual host on a server which, previously hosted a single website (domain name). Now I'm trying to add a second domain on this server (using the same nameserver). What I've done so far: Initially there was no virtual host so I've made one for the second domain: NameVirtualHost *:80 <VirtualHost *:80> DocumentRoot /var/www/bla ServerName www.blabla.com ServerAlias blabla.com <Directory /var/www/blabla> Order deny,allow Allow from all AllowOverride All </Directory> </VirtualHost *:80> Because nothing happend, I changed the DocumentRoot of the apache server to /var/www (initially was the root document of the first website -/var/www/html) and created a virtual host for the first domain too: <VirtualHost *:80> DocumentRoot /var/www/html ServerName www.first.com ServerAlias first.com <Directory /var/www/html> Order deny,allow Allow from all AllowOverride All </Directory> </VirtualHost *:80> In this case, first.com is working ok, but bla.com not. When I ping blabla.com I get the "unkown host" response. What am I doing wrong? Do I have to modify something in the DNS settings too? Thank you.

Read the article
Linux on Sony Vaio VPCEB1S1E

- by Jaakko

I bought Sony Vaio VPCEB1S1E and I was able to surf on net. Then I tried to install Ubuntu 9.04 and Linux Mint on it but neither allows me an access to the Internet. How can I configure Mint so that I can go to net and get updates via apt-get? jaakko@jaakko-laptop ~ $ ifconfig -a lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) pan0 Link encap:Ethernet HWaddr 46:83:d4:f4:36:bc BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 78:dd:08:c5:61:88 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster0 Link encap:UNSPEC HWaddr 78-DD-08-C5-61-88-00-00-00-00-00-00-00-00-00-00 UP RUNNING MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) jaakko@jaakko-laptop ~ $ ping 8.8.8.8 connect: Network is unreachable

Read the article
Weird routing issue

- by Joel Coel

I'm having some weird internet problems on campus. I know it's something simple, but it's a case where I need another set of eyes. I think I can explain the problem best by posting a tracert: Tracing route to google.com [74.125.45.147] over a maximum of 30 hops: 1 3 ms 3 ms 3 ms 192.168.8.1 2 1 ms 1 ms 1 ms elissaemily-pc.york.edu [192.168.10.5] 3 2 ms 2 ms 2 ms rrcs-76-79-19-33.west.biz.rr.com [76.79.19.33] 4 31 ms 3 ms 2 ms ge-1-1-0.lnclne00-mx41.neb.rr.com [76.85.220.109] 5 20 ms 17 ms 17 ms ge-7-3-0.chcgill3-rtr1.kc.rr.com [76.85.220.137] 6 20 ms 20 ms 19 ms ae-5-0.cr0.chi30.tbone.rr.com [66.109.6.112] 7 19 ms 19 ms 24 ms ae-1-0.pr0.chi10.tbone.rr.com [66.109.6.155] 8 26 ms 24 ms 24 ms 74.125.48.109 9 23 ms 24 ms 21 ms 216.239.46.246 10 39 ms 39 ms 55 ms 209.85.242.215 11 39 ms 39 ms 39 ms 209.85.254.243 12 39 ms 40 ms 96 ms 209.85.253.145 13 39 ms 39 ms 39 ms yx-in-f147.1e100.net [74.125.45.147] Trace complete. Note the second entry in there. Not only is the host name a student's computer, but the ip address doesn't exist. Dhcp shows that host as having a different address and you can't ping any 192.168.10.5. Yet somehow it's routing packets for us (and not very well, either — things are slow right now). The basic network routing table looks like this: Destination Subnet Mask Gateway --------------------------------------- Default Route -- 10.1.1.5 (our firewall) 10.0.0.0 255.0.0.0 -- 192.168.8.0 255.255.252.0 --

Read the article
How can a CentOS 6 guest running in VirtualBox be configured as a LAMP server that can be accessed from the Windows host?

- by jtt89

I was able to conect Centos6 on Virtual Box to Windows (I can ping in both directions) with Host-only Adapter (for connection between the two) and NAT Adapter (to enable Linux on VB to connect to the Internet). I want to set up httpd, mysql and vsftpd servers and in the end easily connect to httpd from Windows based browser and ftp server with a Windows based client as well. I would also want to have access through SSH. I have a general idea of the steps that are involved, but there is also a configuration that I am not sure about at this point. Lets say I follow these steps: yum install httpd yum install php php-pear php-mysql yum install mysql-server mysql_secure_installation yum install vsftpd yum install mod_ssl Technically I have everything installed, but what would be the next steps that I need to take (from the networking point of view, so to speak) to get it all working)? I know I need to configure, at least Apache, and ftp server, but I am not sure how is it gonna work; like where am I gonna be uloading the sites (I know this can vary), how am I gonna know what address to use in a browser if I wanna go to a website x, y, z on that installation etc. This sounds like I need to do some kind of DNS setup and I am kind of stuck at this point. If somebody could give me a general outline of what are the things that need to be done that would be great (I was looking at a lot of websites and I know about etc/sysconfig/network, httpd.config - not too much about it on Apache's site, hostname, hostname -f etc; but it is kind of hard to piece it all together at this point). I am gonna be looking at the books also, but they not always reflect the setup that I have too (VirtualBox). Thank you.

Read the article
How to make DD-WRT router's (configured like a repeater) devices be accessible on LAN? (i.e. integrate DHCP for both routers)

- by Annonomus Penguin

I have a D-Link DIR-600-A1 router running DD-WRT (using the 601's firmware: except for the model number, they are near identical). It has an Atheros chip, so there is no "repeater" option. You can bypass this by setting the main radio as a client to the main router, and adding a virtual radio configured as an AP. You can then set up the credentials for connecting to the main router and allowing devices to connect to the repeater/router. I have a few devices on my network: Ethernet computers Server with Samba running WiFi devices connected to the main router I then wanted to add a repeater. I have a couple of other things on the repeater: WiFi Computer Other WiFi devices. Anyway, I wanted to connect my WiFi computer to the share on my server via Samba. However, for some reason, my router treats the main router as WAN, not another device. I've tried disabling the SPI firewall: However, that doesn't work. I've tried pinging my WiFi computer from my server. However, I can ping my server from my WiFi computer. AFAIK, they are on the same subset, just using different IPs: the main one uses 192.168.0.x and the repeater uses 192.168.1.x (starting at 100 for some reason). It seems as I need to configure my router(s) to work together for DHCP. I noticed there was a "DHCP forwarder" option, but I have no idea what that would do. A quick note: for some reason (that's beyond me) my ISP disabled the capability to bridge a WiFi to ethernet connection with the router they provide (something about PPPoE or similar...). The service rep I talked to when I was having issues after I changed ISPs said that, but they couldn't explain exactly what they were "blocking." How can I get DD-WRT to not treat the client connection as WAN and the router to recognize the devices connected to the repeater?

Read the article
Is there any way for ME to improve routing to an overseas server?

- by Simon Hartcher

I am trying to make a connection to a gaming server in Asia from Australia, but my ISP routes my connection through the US. Tracing route to worldoftanks-sea.com [116.51.25.54]over a maximum of 30 hops: 1 <1 ms <1 ms <1 ms 192.168.1.1 2 34 ms 42 ms 45 ms 10.20.21.123 3 40 ms 40 ms 43 ms 202.7.173.145 4 51 ms 42 ms 36 ms syd-sot-ken-crt1-ge-6-0-0.tpgi.com.au [202.7.171.121] 5 175 ms 200 ms 195 ms ge5-0-5d0.cir1.seattle7-wa.us.xo.net [216.156.100.37] 6 212 ms 228 ms 229 ms vb2002.rar3.sanjose-ca.us.xo.net [207.88.13.150] 7 205 ms 204 ms 206 ms 207.88.14.226.ptr.us.xo.net [207.88.14.226] 8 207 ms 215 ms 220 ms xe-0.equinix.snjsca04.us.bb.gin.ntt.net [206.223.116.12] 9 198 ms 201 ms 199 ms ae-7.r20.snjsca04.us.bb.gin.ntt.net [129.250.5.52] 10 396 ms 391 ms 395 ms as-6.r20.sngpsi02.sg.bb.gin.ntt.net [129.250.3.89] 11 383 ms 384 ms 383 ms ae-3.r02.sngpsi02.sg.bb.gin.ntt.net [129.250.4.178] 12 364 ms 381 ms 359 ms wotsg1-slave-54.worldoftanks.sg [116.51.25.54] Trace complete. Since I think it will be unlikely that my ISP will do anything, are there any ways to improve my routing to the server without them having to intervene? NB. The game runs predominately over UDP, so I believe most low ping services are out of the question, as they rely on TCP traffic.

Read the article

< Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108 | Next Page >