Search Results

Search found 3589 results on 144 pages for 'hp mini'.

Page 101/144 | < Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >

• Multiple VLAN on one switch port

  - by Macropus

  I have a HP ProCurve 1810G-8 which I currently use as a normal switch between 3 servers and a firewall. 2 of the servers are ESXi hosts, and one is a Nexentastor box with 2 iSCSI target LUNs. As the iSCSI traffic is on the same LAN as all other traffic, I would like to switch this to use a SAN for iSCSI traffic and the LAN for all other traffic. The Nexentastor box only has 2 NICs, and as such, with a physical arrangement, I presume that one must be plugged into the SAN VLAN and one on the LAN VLAN ports of the switch. Is there a way to have multiple VLANs over the same port? e.g. the Nexentsator box has 2 NICs, both plugged into the switch, both ports with access to both of the VLANs?

  Read the article

• RHEL 5.1 loses changes to /etc/hosts above lines for `localhost`

  - by warren

  Is there a known fix (other than upgrading from 5.1) to fix /etc/hosts from being replaced on reboot? I discovered this behavior when running HP's Server Automation tools. HPSA sets-up a variety of local aliases for itself to use for different components to communicate wit each other. However, after reboot, the hosts files is reverted to a quasi-plain-vanilla version: all lines above the entry for localhost are removed. Manually re-adding those needed lines below the entries for localhost works, but is non-ideal. Is there a fix for this behavior? I do realize that RHEL 5u1 is not officially supported for HPSA 7.8, but the hosts file resetting is not good for a variety of other reasons, too.

  Read the article

• Software RAID 10 on Linux

  - by vpetersson

  For a long time, I've been thinking about switching to RAID 10 on a few servers. Now that Ubuntu 10.04 LTS is live, it's time for an upgrade. The servers I'm using are HP Proliant ML115 (very good value). It has four internal 3.5" slots. I'm currently using one drive for the system and a RAID5 array (software) for the remaining three disks. The problem is that this creates a single-point-of-failure on the boot drive. Hence I'd like to switch to a RAID10 array, as it would give me both better I/O performance and more reliability. The problem is only that good controller cards that supports RAID10 (such as 3Ware) cost almost as much as the server itself. Moreover software-RAID10 does not seem to work very well with Grub. What is your advice? Should I just keep running RAID5? Have anyone been able to successfully install a software RAID10 without boot issues?

  Read the article

• Cisco FC SAN switch decision

  - by Chopper3

  I've got to buy a bunch of FC SAN switches in the next week or so, I have to, and want to, buy Cisco MDSs. Servers are HP BL490c G6's in C7000 chassis with Virtual-Connect Flex-10 ethernet interconnects and VC FC interconnects (Emulex HBAs btw), all running ESX 3.5U4 (for now). I think I've only really got two choices; MDS 9509's with dual-supervisors with a single 48-port 4Gb FC card MDS 9222i's with single supervisor and the built-in 18-FC-port/4-GigE-FCIP-port option Both have the same functionality (I think, buying the enterprise licence btw), both have plenty enough performance and adequate ports for now and the next three years. The 9222i's are about 55% the price of the 9509's - logic says get the 'i's but will I really miss the dual-supervisors? I've got lots of 9509's with dual-supervisors that I'm very happy with but I'm not sure I've every benefitted from the dual-sups in the past and they are nearly twice the price - but if I don't buy them and miss them I can't retrofit them later. What are your thoughts?

  Read the article

• Good Linux Distro for Disconnected Netbook

  - by MrWizard54

  I'm deployed to Afghanistan with the Army and I have a friend who's netbook had his hard drive take a dump on him. He ordered a new hard drive and I was able to download and burn a copy of Ubuntu to disk from work. However the default install doesn't support most of the media that he wants to watch (AVI files, probably some DIVX video) without installing extra packages. We don't have internet in the tent and really don't have a vaiable option for downloading additional packages through the package manager anywhere here. The computer is a small HP netbook. All my friend wants is to watch ripped movies. Does anyone know of a good way to do either of the following: Download packages seperately and install them via CD A distro that is going to come preloaded with all of the packages and needed to watch just about any type of video file you can think of? Thanks in advance, Andy

  Read the article

• Windows 8 slow after refreshing and rebooting

  - by Dan Drews

  First, I apologize if this is in the wrong place. I use S/O a lot but not the other sites much. I have an HP Split X2 that has been very choppy as of late (takes several seconds to respond to any form of input), so I went ahead and did a system refresh. After the refresh everything ran very fast as it should, then when I went to download my old apps I needed to reboot. After rebooting, it went back to the choppiness. Does anybody have any thoughts on what this could be?

  Read the article

• Is it possible to download minimal drivers on Windows, without the extra software packages?

  - by Anton Gogolev

  The situation in all its glory: 30 megs for ATIs' "Display Driver Only". Almost 100 megs for NVidias' GeForce/Ion bloatware. 300 megs for an HP printer driver with immense amount of crap 30 megs for a Realtek integrated sound card driver. 50 megs for a mouse driver ...and dozens and dozens of other similar examples Additinally, UI/UX on vendors' sites is really terrible: I have to carefully pick and choose the exact model of my whatever, although this packages do contain drivers for pretty much every possible hardware model out there. My question is: How and where can I download true minimal drivers without all these ATI "Installation Managers", Realtek GUIs, ASUS tools, etc.?

  Read the article

• Which is better for running Ubuntu and other Linux OSes, Chromebook or Windows, why? [on hold]

  - by Serge

  I'm learning programming and I would like to switch to a Linux OS, perhaps Ubuntu, to continue this, but the current machine is generally getting pretty old and slow and Windows is the least favorite option for production, and I can manage getting something new right around the price range of the nicest Chromebook on the market right now. However, I have compared specs of HP Chromebook 14 with those of regular PC laptops that roughly cost the same, and the latter consistently have approximately the same and sometimes higher (like the processor speed) specs. Yet usage of Chromebooks for this purpose is pretty widespread nowadays. Is this because they were initially built for a Linux OS - and is it really THAT crucial - or are there other major factors at play here?

  Read the article

• How have you saved green by going green?

  - by Bob

  For the purpose of this question, I am interested in server/datacenter related hardware. Have you had any measureable amount of ROI by swapping existing hardware to more "green" or energy efficient hardware? For example, VMWare says you can reduce energy consumption by up to 80% by using virtualization. I have also heard of a cooling solution from HP which is suppose to reduce a small amount of engery usage (<25% I think). Google has also done something by integrating a UPS into their power supplies to reduce energy consumption. Any real world experiences would be great, but if you have any details on initial cost, savings and pay off time about what changes were make that would fantastic. I am not only interested in virtualization, I am interested in anything.

  Read the article

• Scripts on UNC paths take very long to run

  - by Álvaro G. Vicario

  I have several scripts in UNC paths (from Windows batch files to PHP scripts). No matter how I run them (double click on explorer, my editor's run command menu or Windows command prompt) they take really long to start running (like 14 seconds). Once they get started they run normally. This doesn't happen if I run them from mapped drives. I'm using Windows XP Professional SP3 inside an Active Directory domain and files are hosted in a Windows Server box (not sure about the version, it's an HP dedicated file server with bundled OS). Why does it happen? Is there a way to speed up things while using UNC paths?

  Read the article

• Can I use a display driver from Windows 8 in Windows 7?

  - by adam0101

  My latest display driver doesn't support WDDM 1.0, and I need it to be at least version 1.1. I've been attempting to get the Windows Phone 7 SDK working on my HP Pavillion dv9000, but the phone emulator requires 1.1 or higher. My drivers are as up-to-date as they can get. I even tried a modded driver found here, but no go. Then, while evaluating Windows 8 Developer Preview on a different partition I noticed that dxdiag.exe showed it was using WDDM 1.2. I tried installing Windows Phone 7 SDK on Windows 8, but I get an "Internal Error" popup and "Connection failed because of invalid command-line arguments" in the error window in Visual Studio. I'm guessing because Windows Phone 7 SDK isn't supported on Windows 8 yet. So my question is this: Can I get Windows 7 to use the display driver Windows 8 is using to get WDDM 1.2 on Windows 7 and how would I go about doing it?

  Read the article

• How to force a resolution in linux?

  - by hi

  I have a HP LP3065 that requires a dual link dvi cable to go up to 2560x1600 resolution. However, I do not have that cable, but I want to use 1920x1200 resolution. However, my nVidia Display Settings (also system display settings) will only go up to 1280x1024, which looks horribly pixelated on the 30". How do I force the 1920x1200 resolution? I tried adding the mode into my xorg.conf file, but it still would not take it. I know my vid card can do 1920x1200 since it works on the 24" monitor with the same dvi cable. Here are my specs: Fedora 12 Nvidia Quadro NVS 420 Intel Xenon E5530 cpu 6gig memory Thanks

  Read the article

• How can I set my wireless router to run on a time schedule?

  - by Joshua Robison

  I have a Buffalo AirStation WZR-HP-G301NH I am able to access it's settings via 192.168.11.1 I'm connecting wirelessly with toshiba i686 laptop on Linux Mint Debian with service pack 3 and i686 dual core kernel This is just my home network but I know that there must be a way for large industries to shut their networks down or lock out their network access temporarily based on a time schedule, automatically. Like mon - fri the network provides access from 8am to 10pm and then automatically shuts down. I want this to affect all the computers accessing this netowork... basically all my families computers so that the internet just automatically shuts down at bedtime. I am running Linux Mint Debian and so maybe I need to make a cron job or something but does anyone know how big industries implement this and how I can do it privately? TIA

  Read the article

• Configuring Server with no monitor

  - by Scandalist

  Sitting in front of me is an HP DL 380 Generation 4 with no monitor. I'd like to install an OS on the thing but for reasons obvious, I can't. I got excited when I found the ILO port on the back but unless you have a subscription it has limited functionality. I was thinking maybe there was some software out there that booted into some kind of remote access server? When I tested it with a monitor (A friends) I set the BIOS to boot from USB so anything I can load onto a stick should boot. Ideas? Hacks?

  Read the article

• What all laptops can replace a compaq presario v2000's monitor ?

  - by Nishant

  I am planning to buy laptop for parts/repair from Ebay to replace by broken LCD of Compaq presario v2000 . I know the monitor is 14" WXGA and LTNW140-l01 model made by samsung . I have removed the LCD panel and I can see 2 cables , one power and other video signal Can I buy a 14.1" LAPTOP and fit to this ? 14.1 WXGA seems very common . Please can any one tell which all laptops can replace this monitor ? I know HP DV 1000 does ? Any advices would be great .

  Read the article

• Laptop Touch-pad stops working after reattaching parts

  - by kb67

  I was trying to replace my LCD screen for the first time, and it was a very hard process to do. I had to unscrew everything from the bottom of the laptop (Ram, HD, etc) and detach everything that was under the keyboard. After reattaching the LCD, putting everything back together, the touch-pad has stop working. Everything works except for that. Anybody know why it stopped working? I have an HP G61-429WM Laptop. Sorry if this was the wrong place to ask.

  Read the article

• Why is windows 7 marking all my extra RAM as "hardware reserved"?

  - by pinkmuppet

  I have a new HP Z800 Workstation, running Windows 7 Enterprise 64 bit. The machine has 4GB of RAM -- windows reported 1.99GB available, 2GB was "hardware reserved". I added another 2 GB and windows reports that there is 6GB of physical RAM, but now 4GB is "hardware reserved". The BIOS sees the full RAM amount as well. The video card is an nVida Quadro FX 580, so it shouldn't be using any shared memory at all. whats going on? Z800 Specs are here.

  Read the article

• Which driver for "ATI Mobility Radeon HD 3650" in a laptop?

  - by Lasse V. Karlsen

  We have some HP laptops here that comes equipped with a video card that identifies itself as "ATI Mobility Radeon HD 3650", like this one. However, which drivers do we choose? As far as we can tell, HD 3650 is desktop cards, or at least there are no drivers listed for that series with "Mobility" in their name. If I pick the following on the ATI Driver Download page: Graphics Windows Vista 32-bit Edition Mobility Radeon Then the dropdown for the card model contains X300, X600, X700, X800, X1300, X1400, X1600, X1800, 9600, 9700 and 9800 models, but no "HD" nor "36xx series". However, if I change to just "Radeon" for the last selection there, I can find a "Radeon HD 3600 Series" model in the list. Also, if I pick "Windows 7" as the operating system, I can find a "Mobility Radeon HD 3000 series" card, but no 3600. So, which one to pick? The main reason I ask is that they all seem to have some kind of problem installing, so neither seems to be the right one (they all crash with "Catalyst Install Manager has stopped working".)

  Read the article

• Is anyone else using OpenBSD as a router in the enterprise? What hardware are you running it on?

  - by Kamil Kisiel

  We have an OpenBSD router at each of our locations, currently running on generic "homebrew" PC hardware in a 4U server case. Due to reliability concerns and space considerations we're looking at upgrading them to some proper server-grade hardware with support etc. These boxes serve as the routers, gateways, and firewalls at each site. At this point we're quite familiar with OpenBSD and Pf, so hesitant at moving away from the system to something else such as dedicated Cisco hardware. I'm currently thinking of moving the systems to some HP DL-series 1U machines (model yet to be determined). I'm curious to hear if other people use a setup like this in their business, or have migrated to or away from one.

  Read the article

• Mutli-processor workstation as a workstation/server

  - by posdef

  I work in a research institute and a number of programs we use are computationally intensive (I actually wrote one of them). Right now we have one computer that is dedicated for one of these programs (with local accounts only, as in users physically sitting in front of that pc) and the other programs are run on individual workstations assigned to people. I have been looking around to common brands such as Dell and HP, for a some sort of a small/medium scale server, which can be used as a workhorse by sending tasks remotely. It appears as if there is nothing in between workstations with one 6-core processor and a bunch of extras (like fancy graphics etc) and rack mount servers with ridiculous amount of RAM and HDD expansion capabilities but still relatively little number of processors/cores. I wonder if what I am looking for is such a small niche product? Are there other solutions that I might not be aware of? Does anyone know of a multi proc- multi-core workstation/server that is still within the reasonable

  Read the article

• VMXNET3 nic loses the ability to update ARP table after N hours

  - by Peter

  I have a fedora 18 VM that stops updating the arp table on eth1 after running for a number of hours to days. There are other VMs on the same hypervisor that can access all of the same networks without issue. A tcpdump of the offending NIC shows only ARP broadcasts but no responses. None of the other VMs on the vDS see the ARP broadcasts from the offending NIC. The only way I can currently solve the problem is to reboot the VM and then everything works for a while. I've tried changing the port on the vDS and even flipping the network configurations after I lose eth1's ARP table, but the ARP problem follows eth1 but I can access the machines that were originally on eth1. If I statically add the arp entries for machines on the same subnet I have no problems with connectivity. The Hypervisor is an HP BL49X series with flex-10 network modules. Has anyone seen anything like this before?

  Read the article

• Separating user resources - Windows Server 2008 (Terminal Server)

  - by Christopher Wilson

  At the moment I am running a Windows Terminal Server 2008 for around 10 clients that use the server to run programs and access data. Is there anyway to separate the resources of each user so that they do not impact each other in terms of resources. User 1: Opens program User 2: Notices slow down I have looked into using Windows System Resource Manager but do not know if it provides what I need and if there are any other 3rd party tools that also provide this functionality. Any answer is appreciated. Server Specs: HP ProLiant ML110 G7 Processor: Intel® Xeon® E3-1220 (4 core, 3.1 GHz, 8MB, 80W, 1333/t) RAM: 12GB DDR3 ECC 1TB HDD

  Read the article

• cloud/grid computing

  - by tom smith

  Hi guys. I'm appologizing in advance to the guys who will tell me this isn't a tech/server/IT issue! But I've been beating my head around this for a couple of days now. I'm trying figure out who to talk to, or which company I can approach to try to see if there are Grid/Cloud Computing companies who have programs setup to deal with colleges. I'm dealing with a compsci course, and we're looking at a few projects that would require a great deal of computing/computational resources. But in calling different companies (HP/Rackspace/etc..) I'm either not getting through to the right depts, or to the right people, or the companies just aren't setup for this. There are plenty of companies who have discounts for desktop software/hardware, but who in the biz deals with discounts/offerings for Cloud/Grid Computing solutions?? Any thoughts/pointers would be greatly appreciated. Thanks -tom

  Read the article

• Unable to edit CIFS Share permissions

  - by Datapimp23

  Hi, I have this backup Disk to disk device HP Storageworks 2540i. Managing the device is via a web interface. I joined the device into our AD domain in the CIFS server configuration. I then created a CIFS share called backupdata. If I try to access it I'm prompted for a login. The permissions tab in the web interface is empty. The following message is displayed. "CIFS Authentication is managed through Active Directory" However I do not find the share in AD. I forced replication between all DCs and I do not find it. Is there another way to edit the permissions?

  Read the article

• Windows 2008 Print Server issue

  - by HokieMike

  I have a dedicated windows 2008 server I use as a file server and print server at my home office. Whenever I print documents from one of my clients, I see the document hit the queue on the server immediately (says its in "printing" status), but it takes FOREVER to print out (like over 5 minutes). But, printing the same document locally from the server takes 4 seconds. It's an HP 1006P laser printer. I am running 32-bit 2008 Server. Installed the Vista drivers ( updated to latest version ). Tried updating the drivers on the clients too and no dice. Any ideas on how to troubleshoot?

  Read the article

< Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >